How to hang the door on a gorenje refrigerator. How to hang a refrigerator door with your own hands

Most refrigerators are equipped with a door on the right side. This is due to the fact that the majority of the population belongs to the category of right-handers, and it is more convenient for them to operate with their right hand when opening and closing. Left-sided opening is much less common, and such a model must be specifically looked for.

However, the need to rehang the refrigerator doors is often caused by other reasons.

Why do you need to replace doors?

Activity of the right or left hand is quite a sufficient reason for resetting. The door leaf of a refrigerator, especially a large one designed for a fairly large load, is quite heavy. Constantly using the “wrong” hand to open and hold the door is not very convenient.
The second reason is much more common. When choosing and purchasing a device, pay attention to its specifications and ease of use, as well as size, but, as a rule, it is not taken into account that a hinged door will require space to open.
Repair – rearrangement in the kitchen caused by the installation, for example, of a sink or washing machine, required moving and a refrigerator. And, since the kitchen area is usually small, it turns out that the door does not open in the new place, but rearrange refrigerator nowhere else.

The problem can be resolved by reinstalling the sash.

How to replace a refrigerator door.

Before reinstallation, you need to make sure that it is possible: plugs should be placed on the body of the device and on the door on the left side. Some models require the use of additional parts, in which case they should be included in the kit.

How to properly replace the sash is usually described in detail in the manufacturer's instructions. But if it is lost due to the passage of time, then general principles can be used.

Before you move door leaf, you should turn off the unit - it is recommended to completely disconnect it, remove the shelves and containers, and also dismantle the handle.

Using a flat-head screwdriver, lift up and remove the plugs from the bolts.
The fastenings on the body are unscrewed. In this case, you should hold the sash so as not to damage the lower hinge. The photo shows the moment of dismantling the hinge.
The sash rises and is removed from the lower hinge.
The swivel hinges are removed. All existing plugs on the left side are installed on the right side at the mounting points.
If the model does not provide for the use of additional parts, then all removed hinges are mounted on the left side in a mirror image. It is recommended to start installation from the top hinge.
In order to hang the door, you should install it in the lower hinge, and then bolt the upper one. The fabric is adjusted until a tight fit is achieved around the entire perimeter.

The video shows the reinstallation process in a single-chamber refrigerator in more detail.

Replacement features

A huge number of models provide many nuances - hence the advice, first of all, to refer to the instructions.

A two-chamber device with separate fastening - the doors are installed on separate hinges, and by and large, changing the side of one door is not necessary to change the second. In this case, each is dismantled separately, as an independent element.
Two-chamber refrigerator with common fastening - device door hinge such that on one axial rod the hinges of the sash of both the freezer and refrigeration chamber. In this case, re-hanging the door is somewhat more difficult, since simultaneous dismantling and installation of both parts will be required.

Single-chamber refrigeration cabinet with decorative plugs - all fastenings in this case are hidden by decorative panels and, before hanging the doors, you need to unscrew the fastenings and remove the top panel from the lid of the device to gain access to the upper canopies. The same operation must be carried out with the lower mount.

When replacing hinges, you should pay attention to the fundamental possibility of right and left fastening. For example, on many models of Atlant refrigerators, the upper canopy is simply rearranged from the right side to the left. But there is no corresponding hole in the bottom one, so you will need to either buy a left-sided bottom hinge or drill a hole in the existing one yourself.

How to rehang the doors on a refrigerator with a display

The device differs from the regular model in the presence of a display cable located near the top hinge. On models where reinstallation is permitted, the cable has a connector for disconnection.

The bolts holding the door leaf are unscrewed decorative panel. The panel is removed.
The fastening bolt on the top hinge is unscrewed, and the guide with the cable is removed.
The display cable becomes disconnected.
The fasteners on the top or central (depending on the model) hinge are unscrewed, the sash is raised and removed from the hinges.
The top cover of the refrigerator is removed - the control panel is located under it. The cable is routed through the left hole in the panel. The photo shows the control panel on the lid.
The loops are transferred from the right side to the left and secured. According to the instructions, in some models it is necessary to change the mounting post from top to bottom.
The cable is connected and the wire guide is installed.
The top cover and the top panel of the sash are fixed in their original place. All plugs on the left side are placed on the right.

The video explains how to replace doors with a display in more detail.

How to hang a refrigerator door?

The refrigerator door in the vast majority of models is hung on the right side. However, it happens that due to the specific layout of the room, such a door location is extremely inconvenient. In this case, the problem can be solved by rehanging the door. And today we’ll talk about how to hang the refrigerator door.

Beginning of work

Let's start, of course, by determining the very possibility of hanging the door. You can determine whether it exists by looking at the rotary hinges and plastic plugs. Rotary hinges and plastic plugs intended for fastening the door must be located on the opposite side of the door, as well as on the refrigerator body. Some additional parts may also be required, which are usually supplied by the manufacturer. If all the components are in place, prepare the tools. To do this, we only need a couple of screwdrivers (regular and Phillips) and, in some cases, wrenches (usually #8 and #10 wrenches are required). Now turn off the refrigerator and unplug it from the socket to completely cut off the power. After this, you need to pull out all the shelves so that they do not interfere with the rearrangement, and also remove the refrigerator door handle. Next, use a flathead screwdriver to remove the plastic caps from the bolts. After this, unscrew the fasteners from the refrigerator body. At the same time, hold the door and, as soon as you unscrew the bolts, carefully remove the door and place it on the floor.

Door removal process

Now we need to free the door from the rotary hinges, which we remove with a screwdriver. Then we change the plugs from the mounting location, installing them in the old place - where the mounting bolts were previously located. If the model of your refrigerator provides for the use of the same parts in case of rehanging, simply screw the hinges to the door in the opposite way, that is, in a mirror manner. However, this is not always possible, and other parts may be needed to secure the door on the opposite side - in this case, I recommend that you study the operating instructions for your refrigerator model. Having decided on this, we remove the plugs for the rotary hinges from the left side of the refrigerator and move them to the right side. Well, now all we have to do is lift the door itself and, placing it in a suitable manner against the refrigerator, screw on the hinges and, if necessary, adjust them. It should be noted that it is best to start screwing the hinges from the top - this way you will protect yourself from parts breaking. After you screw the door, don't forget to put the handle and shelves back. If your refrigerator door is equipped with a sensor, then sometimes you may need to re-hang it, for which there should also be holes on the opposite side.

We rehang doors in specific models

We described the procedure in general, but did not dwell on specific cases, since there are many models of refrigerators and it is not possible to describe this procedure for all brands. However, we have prepared for you some useful links on how to hang the door on various popular refrigerator models.

Instructions

Make sure your refrigerator door can be moved. Inspect the refrigerator. You should find plastic plugs that are designed to secure the handle, as well as the rotary hinges located on the door. There should also be fastenings on the refrigerator body.

Unplug the refrigerator to protect yourself from electric shock.

Empty the refrigerator of all food and remove the shelves.

Remove the door handle.

Remove the door plugs using a flathead screwdriver.

Unscrew the fasteners from the side of the refrigerator while holding its door.

Carefully remove the refrigerator door.

Unscrew the hinges from the door. On the opposite side of the door, remove the caps for the hinge holes.

Screw the hinges to the opposite side of the door, mirroring the previous position.

Locate the hinge plugs on the left side of the refrigerator body. Take them out, then replace them in the holes on the right side that were used previously.

Place the door against the refrigerator and tighten the hinges. Adjust them if necessary.

note

To rehang the doors of some models of Indesit refrigerators, additional parts are required. For example, sometimes other loops are needed. They come complete with the device. Before you begin reinstallation, check your refrigerator's instruction manual to ensure that these parts are included.

Helpful advice

Some refrigerator models require reinstallation of the door opening sensor after rehanging. This is indicated in the operating instructions. To reinstall the sensor there are special mounting holes, made from the opposite side.

Sources:

Re-hanging the refrigerator door
re-hanging the refrigerator door

It happens that the door in the apartment is hung in such a way that when opened it blocks the window, and you look at the blank wall with displeasure. Naturally, it will be much better if, with open doors you will see a window. However, there are other cases when it is advisable to hang the door so that it opens outward rather than inward.

You will need

Screwdrivers, knife, metal ruler, chisel, mallet, thin-headed hammer, plane, thin wire nails, wood glue, wood putty

Instructions

For reweighing doors you will need to move the latch release plate, make new slots for the hinges in the box and in the doors, and also seal up old nests. If you intend to change the opening direction doors, then you will need to move the door stop, or even rearrange the handles. It is possible that the door will have to be repainted.

Find the plugs on the refrigerator body for fastening the rotary hinges on the left side of the refrigerator. Take them out and place them in the previously used holes on the right side. Lift the door, place it against the refrigerator and screw on the hinges, starting with the top ones. Adjust them if necessary.

Please note: on some models, after re-hanging the door, the door opener must also be re-installed. For this purpose, mounting holes must also be provided on the side opposite to the current position of the sensor.

Video on the topic

Sources:

how to change refrigerator doors

It happens that door It doesn't open in the direction you would like. At the same time, it can block something or simply take up extra space in small room, if it opens inward. To get rid of such inconveniences, you can door just outweigh.

Instructions

First of all, remove door. Remove the screws of the lower hinges and the screws of the upper (except one). Then remove the loops from door frame. Put door onto the pretend block and secure it. Using a chisel, cut out the socket and, applying the loop, mark its position, and then install.

After this, you need to turn the latch so that the bevel can enter the lock plate. Secure to the heel block door. Door handles and faceplate must be removed.

Remove the latch from the hole, rotate it 180 degrees and insert it into the hole, attaching the faceplate with screws. Now let's install door handles.

Then you should remove the brass retainer plate from the box, cut the same one out of wood and glue it to the same place.

Now place it vertically door so that the heel beam is at right angles to the box, and secure with wedges. Mark the location of the hinges on the box. You need to go over these marks with a knife, making a groove and then a nest. Finally door You can hang and insert the latch in the right place.

Sources:

Sometimes it is necessary to turn the door so that it does not open

Arranging furniture in the kitchen sometimes requires re-hanging the door refrigerator to make it more convenient to get food. This operation can be performed by store employees before issuing a warranty or by special repair services, or you can also try to rehang it yourself door refrigerator « Atlant».

Instructions

Contact the employees of the store where you purchased the refrigerator " Atlant" Let them know you need to weigh on it door. This will be provided absolutely. After which you will be able to receive a warranty sheet with the relevant information. This method can only be performed until the purchase is finalized. Otherwise, store employees will direct you to service department where this service will cost certain.

Empty the refrigerator of all food items, remove shelves and drawers. Turn off the device and defrost. After this you can start repair work. Stack the refrigerator Atlant» on the floor with the door facing up, making sure that the upper supports have not moved and the radiator is not damaged.

Find the bolts in the recesses that hold the front supports. Unscrew them and free access to the stoppers that secure the door axles freezer. Remove them to reposition the lower door axis to the opposite side. After that, remove door freezer compartment and move the end caps to the other side.

Open door refrigerator compartment to reach two screws. By unscrewing them, you can mask refrigerator. Remove the bracket from the top axle and unscrew it, then move it to the other side. Replace the plastic plug and reinstall the mask refrigerator.

Press the latch that is located inside the handle refrigerator « Atlant", and try to push her out. You must act carefully, as this part can easily break. Using a screwdriver, feel for the latch inside the device to remove the handles. Swap the plugs on the side ends of the door refrigerator and set the handle to the opposite position.

Sources:

how to change a refrigerator door

Most models of modern refrigerators provide the ability to rearrange the doors. Sometimes, especially if the kitchen is not large, this can be very convenient. Re-hanging doors requires certain knowledge and skills. Therefore, it is recommended to invite specialists from the service center to carry out this work. However, if you are completely confident in your abilities, you can try rearranging the doors yourself.

Instructions

Unplug the refrigerator from electrical network. Get all the products. Remove shelves and drawers.

Tilt the refrigerator at an angle of 45 degrees and lock it in this position. This is necessary in order to gain access to the lower hinges.

Remove the decorative panel. Unscrew the mounting bolts using a screwdriver and remove the lower hinge and washers. Remove the bottom door.

In standard refrigerator models, the door opens on the right side, but some manufacturers provide design features, allowing you to move the door leaf to the opposite side. This makes it possible to make the model ergonomic and comfortable to use. You can do such manipulations yourself with a basic set of tools.

Situations that require reversing the doors to the other side:

Left activity, not right hand- a good reason for outweighing.
When choosing a model, we pay attention to technical features, dimensions, ease of use, but we forget that space is needed for the sash.
Rearrangement in the kitchen associated with the repair or installation of a sink or washing machine.

Idea to implement rehanging refrigerator doors This problem has recently arisen among manufacturers. It is better to replace the doors in models with two chambers. It is more difficult to do this with single-chamber representatives; you have to simultaneously hang the freezer door. Convex handles are inconvenient for installation. There is an opinion that when moving, a door that does not close tightly is corrected, but the likelihood of this is minimal. More often the cause is a damaged rubber band. It should be replaced to get rid of the problem. If the problem is deformation or loose fasteners, then reweighing helps. The operation of rehanging the refrigerator doors is simple. All you need is flat screwdriver and wrench . The fastening elements on different models are different, and the size of the tools is selected for them. It wouldn't hurt either regular tape. Before starting work, turn off the power to the refrigerator and remove food and shelves. The doors themselves are bulky, heavy, but fragile, which can lead to damage. Get the job done gloved. U two-chamber refrigerators The doors are mounted on three brackets. One is installed on top, the second - in the space between the doors, the third - on the bottom. First make sure you have the reverse side plugs and swivel hinges. Mounting parts are included in the package. If not, buy them from the right company. Work process:

Using a screwdriver, remove the plugs from the bolts and disconnect the fastening. To prevent the lower hinge from becoming deformed, it should be held after detaching the fastener.
Before removing the door, secure it with tape. Thanks to this simple procedure, the door will not swing open and fall in the middle of the process.
The rotation axis mechanism is installed on the middle bracket. Remove it carefully.
Remove the bolts on the middle bracket. After removing it, disconnect the door from the bottom.
Remove the last bracket and install it mirrored on the opposite side, into the existing holes. If there are cover bolts there, install them in the vacant space.
Next, change the handles. They are attached with screws. Often the fastening mechanism is hidden by a plug. Carefully pry it open with a sharp object or a miniature screwdriver. Be extremely careful, because the handles are made of plastic; using excessive force when screwing in can deform the material.
Move the stoppers (metal parts located at the ends that prevent the doors from swinging open) in a mirror image to the other side.
Reinstall all parts on the other side in reverse order. Attach the brackets conscientiously, they are the ones that hold the entire weight of the doors with products.
Reposition the sensor if necessary open door.

For models with an electronic scoreboard, it is better to invite professionals, because you will have to move the display cable, and this is difficult. If the doors are rearranged incorrectly, they will leak warm air, and the compressor will start working harder, eventually causing a breakdown. To avoid this, after installation, tilt the refrigerator back slightly and the door will begin to close more tightly. If the refrigerator is under warranty, remember that your intervention will void it.

In the modern world, a refrigerator, if the door cannot be moved to the other side, has little chance of withstanding competition. Let’s say a piece of furniture should be placed near a window. A chair was placed opposite. The location is good - comfortable to read. The refrigerator door opens: you have to walk past the rider, reaching the window. Uncomfortable? The answer is yes. Let's see how to hang a refrigerator door.

Solution: moving the refrigerator door

It’s easier to type a search query, looking for something that resembles what you have at hand. Today we will look at the process, using the example of Atlant refrigerators. Stop hoping that the sequence of actions clearly resembles an arbitrary pattern. Read the recommendations above (YouTube).

So, the door usually just starts opening to the other side. It may seem unusual. Previously, the street light fell into the freezer of the refrigerator, now you have to be content with the kitchen. Otherwise, the ability to move the door to the other side is difficult to overestimate.

Re-hanging the Atlant refrigerator door

An approximate sequence of actions awaiting the owner, who is racking his brains and planning to rehang the refrigerator door:

External inspection of the refrigerator to determine access and fastening. If necessary, you will need to remove unnecessary things. Applies to products decorated with door trays.
Typically the top trim panel blocks access to the top hinge. You will have to dismantle the interfering (decorative) parts.
Dismantling the top hinge, rearranging the plugs. Removing the top door.
Dismantling the central hinge, working with plugs. Removing the lower door.
Rearranging the bottom loop.
Reassemble the entire structure in reverse order.

Now let’s see how it all looks using the example of two-chamber Atlant refrigerators, where the freezer is on top.

Removing the doors of the upper decorative panel of the Atlant refrigerator

The process begins with the top decorative panel of the refrigerator. The hiding bracket that forms the top hinge of the freezer door (located at the top). The decorative panel of the refrigerator is held in place by two self-tapping screws; the heads can be easily found if you take the trouble to look. Unscrew with a barrel. A screwdriver equipped with a thick short handle. Those using the “barrel” do not move the refrigerator away from the wall. The distance is small, but a screwdriver will fit there.

We remind you: Atlants have wall stops attached to a decorative panel. It seems absurd, but it works in practice. To remove the stops or not, decide for yourself. First, the top of the refrigerator must be cleared of all sorts of feminine items and jewelry. Flowers, tablecloths, TV. We suggest taking photos from several angles of the refrigerator before starting work. Believe me, it helps to put it back together.

The screws are unscrewed, you need to pull them decorative element refrigerator forward. The trailing edge rises up. You have a chance to see a sheet of foam plastic under the panel. Thermal insulation of the refrigerator. Proceed with caution for fear of harm. The panel must be carefully removed to the side. In many refrigerators you can see a front steel threshold that acts as a support for the panel. There is usually no need to remove it; the part is powerless to prevent the removal of the freezer door.

Doctor Aibolit is finalizing a medical refrigerator

Removing the upper hinges of the Atlant refrigerator

The upper hinge is represented by a plate with a pin screwed into the corner that holds the door. On the opposite side of the refrigerator we see a completely similar detail. The pin is missing, but the thread is present. In the video instructions, it is recommended to seal the refrigerator door with tape. Let's add that in most cases it is enough to hold it with your hand. The door adhered well with a rubber seal to the body of the refrigerator.

The bolts holding the plates are completely ordinary. Take them both off. The pin needs to be unscrewed; the design is not symmetrical. Based on the circumstances, carry out the necessary operations. You will need a hex wrench. Now is the time to move the door hole plug from a previously unused area. Easier to do with a thin slotted screwdriver. Please note that the hole on the developed side is thicker; you will have to seal the plug with a layer of paper. It is important to push the decorative element in completely, preventing the door from catching the top panel of the Atlant refrigerator.

To remove the top door of the refrigerator, use both hands to open it wide and lift it up.

Dismantling the central hinge of the Atlant refrigerator

The center hinge is held in place with Torx bolts. Two pieces each. The loop is asymmetrical, no need to disassemble. Just flip it over. It's time to discuss gaskets. They look like randomly shaped pieces of plastic attached to a central loop. Carefully remove and place aside. Each set is formed by two lower gaskets, the same number on top. Total, four.

With the help of spacers, the technician adjusts the height of the refrigerator door hanger. Although the original purpose is to reduce friction. The hinge is set aside; when removing, hold the bottom door of the refrigerator. Surely it will begin to fall; eggs that have mastered the trays will fall out differently. Hold the door constantly while removing the central hinge. Barring an unexpected fall.

The bottom door of the refrigerator is removed from its hinge and set aside. Note that it hides another set of gaskets. Set the parts aside; you'll need them later. Now we take out the plugs from the opposite side and stick the loops in instead. There are no problems. The plugs are still removed using a thin screwdriver. With the bottom door of the refrigerator, you will have to use the previously tried newspaper trick. Otherwise, the plug will refuse to stand up.

Dismantling the bottom hinge of the Atlant refrigerator

The bottom hinge of the refrigerator is represented by a single threaded rod. It is secured to the bracket from below with a nut. To get there, remove the decorative panel. It is held in place by two Torx head bolts. The size often follows the central loop. Look for access from the front.

Hold the end of the stud in a hexagon shape until the nut opens from below. The nut is typical. Use any type of key. The limitation is caused by the proximity of the floor - it is difficult to crawl up.

Installation of the lower hinge of the Atlant refrigerator and the door

Move the pin to the other side of the refrigerator (a similar bracket) strictly symmetrically, screw it in, holding the hexagonal end on top. Make sure it is securely tightened, then return the plastic spacers you removed earlier. Place the door on top. It is advisable to consolidate or start immediately...

Installation of the middle loop of the Atlant refrigerator

When flipped 180 degrees, the geometry of the relative position of the hinge and doors remains the same. The lower gaskets are at the bottom, the upper ones are still where they were. With one hand, insert the hinge into place, with the other, begin to align the door with the body of the refrigerator, achieving a strictly vertical position. It's clear, building level It won't help much here. Make sure that the upper and lower edges of the door protrude at the same distance relative to the side of the cabinet.

Take it Torx screwdriver, begin tightening the bolts while keeping the door in position. Make final adjustments using a key.

Installation of the top hinge and door of the Atlant refrigerator

Place the spacers on the middle loop
Install the freezer door.
Close the sash with pressure. To keep the door stronger.

Now the door is stuck with the “suction cup” of the seal, we begin to install the top hinge. Let's agree that we have already assembled and tried on, as was said at the beginning. We put on the gaskets, stick the pin into the door, and begin to tighten the bolts. The far one is strong, the near one is light. We align the position of the door so that in the future the upper decorative panel does not catch. A difficult moment... the panel will be pressed down by the weight of the flowers that were removed earlier. When trying on, press firmly from above with your hand.

Here our readers will say a lot of kind words to different addresses, try to avoid breaking the foam sheet. Keep it away from the refrigerator while trying on. It will be easier to put the decorative panel in place. They forgot to glue the foam sheet. Just set it aside. Below is reflective insulation, try to protect.

All that remains is to put the decorative panel back. Guided by the photo, we place the flowers, lay out the tablecloth, and level the TV. Headache you can forget about how to hang the refrigerator door. The review will help readers solve the issue simply, as the authors did with the Belarusian Atlas.