Calculation of fees for hot water. Just about the complicated stuff: calculating the cost of hot water

In order to pay for cold and hot water supply services, data on the water used by the meter must be transferred to the appropriate authorities. Before transmitting information, you need to learn how to take readings from a water meter. We will help solve this problem.

Types of water meters

There are only two types of water meters; understanding them will not be difficult. They differ from each other in the color of the markings and inscriptions on them:

Black or blue. The counter is designed for accounting cold water.
Red. The counter is designed for accounting hot water.

The use of a red meter for cold water metering is not prohibited, so two identical meters can be located nearby at the same time. In order to take readings correctly and transfer them to the water utility service, you need to determine which meter belongs to cold and which to hot water.

How to determine which meter is cold and which is hot

If both water meters have red markings, then you should determine which one belongs to what. To do this, there are two ways to determine whether the meter belongs to a hot or cold water supply:

Location relative to each other. According to the standard, the cold water meter should be located lower than the hot one. This condition is not mandatory, so during installation the meters can be located in a way that is convenient for the master. This can make it difficult to determine which meter is which.
Turning on the water. To accurately determine which meter belongs to cold water, regardless of their location relative to each other, you should open the cold water tap. After opening the tap, one of the meters will begin to rotate, this will be the cold water meter.

Numbers on the meter

Water meters have 8 rotating cells on which numbers are displayed, which constitute the meter readings necessary for the transfer of water.

The last three cells display liters of water used. The first five refer to cubic meters.

After reaching the numbers 999 on the last three cells, they are reset to zero, and the fifth cell is wound up to the number 1. As water is used, reaching the number 9 on the cell leads to the transition of the left sector to +1.

What numbers to consider when transmitting meter readings

When transmitting meter readings to the water utility service, you should record the data in the first five cells. The last three do not need to be written down, but you can round off the fifth digit to account for them.

Example. If the following data is marked on the meter: 00213 621, then the following data can be submitted to the water utility service: 00213 or the following: 00214 in favor of rounding to the nearest liter.

Water consumption accounting

If you are using a new meter, then you do not need to calculate the monthly water consumption; it is displayed in the first five cells and corresponds to cubic meters. If readings are not taken for the first time, then the previous ones should be subtracted from the new meter readings.

Example. If the following data is marked on the meter: 00213 621, and in the last reading period it was: 00208 002, then the consumption can be calculated by simple subtraction: 00214 (taking into account rounding to liters) – 00208 = 6 cubic meters.

When transmitting data about used water, the readings from the cold and hot meter are summed up, and the readings from the hot meter are indicated as water heating in cubic meters.

Example. If the water consumption according to the cold meter is 6 cubic meters. m, and hot 2 cubic meters. m, then the cold water consumption is calculated as follows: 6 cubic meters. m + 2 cu. m = 8 cu. m. Water heating is installed in a volume of 2 cubic meters. m.

Payment for sewerage is carried out for the volume of hot and cold water used together, i.e. will be 8 cubic meters. m.

Video about correct water meter readings

It is not difficult to take into account water consumption according to the meter readings yourself. The readings transmitted to the water utility should be recorded for ease of accounting for consumption in the next period.

Every month you have to pay bills, including payment for water supplied to your home. To save money and control the consumption of this necessary resource, special meters are installed. In addition, there are such counting devices separately for hot (DHW) and cold (CW) water.

In this case, the counters will tell you how to count; they differ in color: red is for a hot resource, blue is for a cold resource. There are eight digits on the dial of the device, the last three of which are marked in red, the rest – in black. Liters consumed are marked in red. Next, you should calculate the water using the meter.

How to count water using a meter: example

Many users are concerned about the question of how to calculate water using a meter. The first five digits, which are black, are transmitted to the controlling company. These are cubes of water consumption for a certain time. If a new device was installed, and at the end of the reporting period the value on it, for example, is 00024843, then this means that consumers in this house used 24 cubic meters and 843 liters of water. So how to correctly calculate how much to pay? When transmitting readings to the monitoring company, it is advisable to round them up, that is, transfer 24 cubic meters. If after another month the meter readings correspond to 000495900, in order to calculate how much to pay, the readings of the previous month should be subtracted from them. Here's how to calculate it:

49 — 24= 25

The calculation system is not at all complicated. That is, the consumption of the last month is 25 cubic meters, therefore, we will find out how much to pay after multiplying by the tariff for 1 cubic meter. In subsequent billing months, payment is also calculated.

How many Gcal in 1 m3 of hot water

How to calculate hot water? You have to pay more for hot water supply, because it uses heat to heat it up. So how many Gcal are in 1 m3 of hot water? In today's difficult living conditions, the topic of saving is extremely acute.

Important! 1 Gcal is the amount of heat required to warm a thousand cubic meters by one degree. It follows from this that there are 0.001 Gcal in one cubic meter. When calculating, this value is added to the total losses in the house, which are caused by the inevitable cooling of the water while it reaches the payer’s apartment. The pipes through which this resource passes are a common property, so everyone must also pay for these losses.

The price of hot water especially increases where it passes through heated towel rails in bathrooms, in fact heating the entire room. In this case, up to thirty-five percent of heat can be lost. Rather, these heat costs relate to heating. But the meter doesn’t know this; it only calculates the flow rate that has reached it.

Unfortunately, it is impossible to change the existing pipe layout. It is not recommended to throw away heated towel rails, because they are a component heating system, without them, the normal circulation of the resource through the pipes will be disrupted. In this case, it will need to be drained for a long time, which will definitely cost a pretty penny.

There is another concept of 1 cubic meter of hot water - for heating. The amount of heat for DHW does not change in this case either. But usual way The calculation in this case is incorrect. What do these columns mean on the receipt and what does the payment consist of?

The consumer divides the indicators from column Q by column V1, i.e. Gcal per m3, resulting in a huge value. This is especially true for those who have volatile automation installed. In this case, the figures are significantly overestimated. The user is perplexed why they have to pay so much more for a cubic meter of water. Why was it necessary to bear the costs of installation and a new device if the price for the consumed water supply has not decreased? Is the company lying?

Important! One Gcal is the volume of heat that is needed to heat a thousand cubic meters of water by one degree (it would be more correct to say thousands of tons). The note about tons was not made in vain, because the density of water at different pressures and temperatures is not the same. When heated, it expands and its quantity increases. But when she went around all the apartments, her temperature drops and the volume decreases, but in tons it remains unchanged.

The error may be caused by the inaccuracy of the measuring instruments themselves. A discrepancy may occur when heat consumption is less than 0.5 Gcal hourly, since reprogramming is possible based on the actual pressure in the IHP. Pressure does not have a significant impact on overall accounting (no more than 0.1 percent of overall accuracy). An error may also be made when calculating the temperature difference between the hot water supply and return data.

How to challenge water heating regulations

What to do if the consumer does not agree with the standard for heating water, and is it possible to challenge it? Of course you can. For example, if a water heater breaks down, the water supply organization must repair it urgently. All residents must pay for the repairs if it is an apartment building.

If you need to resolve the issue individually, you should call the organization responsible for the water supply and call an inspector who will draw up a malfunction report. If you cannot reach an understanding with the company by any means, you can go to court. But in such cases, litigation is rarely resolved in favor of the residents.

A water meter helps you save money cash, but it is important to be able to correctly interpret his testimony and calculate payment. Determining how much to pay for each of the meters (for hot and cold water supply) is not at all difficult. You need to independently take into account the cubic meters consumed each month and compare them with the data in the housing and communal services receipt. As with all utilities, payments for water are made monthly. The Internet will help you find out what the tariff is this year.

When all this is finished, the actual exploitation begins. And here the question arises: how to pay for water using the meter, where to go, and how is water consumption calculated in general?

How to take readings from the meter?

Five black and three red. For example, initially the counter showed the following data: 00000174. Here 174 is the number of liters of water used. As you know, readings must be taken in cubic meters, so it is too early to transmit them. In other words, the readings from the meter are taken based on the first five digits, so you can wait a month.

A month later, look again - the readings are already different: 00001174. In this case, they can already be taken, because there are more than three digits. It turns out that you use a little more than 1 cubic meter of water per month. When sending indicators, the amount is rounded, you pay only per cubic meter. Another month later we see on the water meter: 00012566. Now it turns out that 12 cubic meters were used. Subtract 12-1=11. This month you pay for 11 cubic meters of water.

Calculation of water consumption by meter

For calculations you will need two things:

meter readings;
current tariffs for hot and cold water.

After installing the meter, record its initial readings.
Report the data to the management company.
After a month, you take the readings again, determine the difference and report it (we’ll talk about reporting the readings later).
To independently calculate the amount to be paid, use the tariff table.

Important! Tariffs change annually, and they are also set by the city administration. Therefore, in the future, periodically inquire about them by calling the management company.

To determine hot water consumption, multiply the water meter readings by the tariff. This will give you the amount you need to pay for water consumption this month. WITH cold water the procedure is similar.

Remember that in some cities there is a certain the minimum you have to pay monthly. In this case, even if you used an amount of water less than this minimum, for example, 10 liters with a minimum of 1.5 cubic meters, you will pay for the entire 1.5 cubic meters. But next month the company will take into account the overpayment and you will pay less.

If you are interested, how to pay for water in the village, then we hasten to reassure you - the procedure there is no different from paying for water in the city. The only difference can be in the tariffs, and as already mentioned, you can find out about them from the management company.

Procedure for paying for water by meter

In order to pay for water supply services, you must submit monthly meter readings to the Unified Information and Calculation Center (hereinafter referred to as EIRC). There are several ways to do this:

call the EIRC and provide the data to the dispatcher;
do this via the Internet by visiting the resource of the management company (the vast majority of them have their own websites);
personally visit the EIRC and leave an entry in the appropriate journal;
send the indicators by mail to the EIRC.

Payment center employees will calculate the amount and send it to you using a special payment document. This happens once a month; a personal visit to the center is not necessary. Remember that the building maintenance directorate may check from time to time how well the readings you give correspond to the real ones.

Important! If a water meter is installed in a communal apartment, then the amount payable is equally distributed among all registered residents.

If several water meters are installed in the apartment, then provide readings for each of them separately. It is not recommended to interfere with the operation of the meter, slow it down, etc., since if such violations are detected, you will face a fine.

Checking the correctness of the readings

It happens that the counter shows incorrect data. To check this, write down the indicators of the three red numbers. Then take a ten-liter bucket, fill it with water and pour it out. Repeat the procedure three times. Look at the water meter. If the numbers show that more or less than 30 liters have been used, then your water meter needs to be checked.

If the counter is lying

If you notice that the meter is showing false information, you should check it. The verification will be carried out at your expense. If the meter is under warranty, then the certified company that sold it will pay. During this time, you will pay for water according to your average monthly consumption. After the check is completed, it is carried out or replaced. If you overpaid, a recalculation occurs and the overpayment amount is returned to you.

Now about the cause of the malfunction. Your guilt is determined if the seal on the meter is damaged, the glass is broken, or the arrows are missing, if a scheduled check was not done. Then you will face a fine.

What happens if you don't pay for water?

Payment for water supply services must be made by the tenth day of the next month. If payments are not made within three months, you will receive a first warning from the utility company. If you do not pay for six months, then the utility companies have every right to go to court in order to collect the debt from you.

In general, the Housing Code of the Russian Federation is very treats defaulters harshly. The sanctions provided for them begin with fines and end with eviction from the apartment with confiscation of valuables. So be careful.

Video – Water debtors face trial

In the near future, residents will begin to pay for hot water according to a new principle: separately for the water itself and separately for heating it.
So far, enterprises and organizations are already using the new rules, but for residents the old accounting remains. Due to communal confusion, housing services companies are refusing to pay heat energy companies. Fontanka understood the complexities of the two-part tariff.

Earlier

Until 2014, the population and businesses paid for hot water as follows. For the calculation it was necessary to know only the consumed number of cubic meters. It was multiplied by the tariff and by the figure artificially derived by officials - 0.06 Gcal. This is exactly the amount of thermal energy, according to their calculations, that is needed to heat one cubic meter of water. As Deputy Chairman of the Tariff Committee Irina Bugoslavskaya told Fontanka, the indicator “0.06 Gcal” was derived based on the following data: the temperature of the hot water provided should be 60 - 75 degrees, the temperature of the cold water used to prepare hot water should be 15 degrees in winter, 5 degrees in summer. According to Bugoslavskaya, committee officials made several thousand measurements, taking information from metering devices - the artificially derived figure was confirmed.

In connection with the use of this payment method, a problem arose with risers and heated towel rails connected to the hot water supply system. They heat the air, that is, they consume Gcal. From October to April this thermal energy is added to heating; in the summer this cannot be done. For a year now, a system has been in place in St. Petersburg according to which payments for heat supply can be charged only during the heating season. As a result, unaccounted heat is generated.

Solution

In May 2013, federal officials came up with a way out of the situation of unaccounted for heating with heated towel rails and risers. To achieve this, it was decided to introduce a two-component tariff. Its essence lies in separate payment for cold water and its heating - thermal energy.

There are two types of heating systems. One implies that the hot water pipe comes from the one intended for heating, the other implies that for hot water, water is taken from the cold water supply system and heated.

If hot water is taken from the same pipe as heating, then payment for it will be calculated taking into account the costs associated with chemical treatment, staff salaries, and equipment maintenance. If cold water from the State Unitary Enterprise “Vodokanal of St. Petersburg” is used for heating, then the payment for it is taken according to the tariff - now it is a little more than 20 rubles.

The heating tariff is calculated based on how many resources were spent on the production of thermal energy.

Confused housing residents

From January 1, 2014, a two-component tariff was introduced for consumers who do not belong to the “population” group, that is, for organizations and enterprises. In order for citizens to be able to pay according to the new principle, it is necessary to make changes to regulations. Pay by new system provision rules prohibit utilities. Since residents are still paying old scheme, housing organizations serving buildings with non-residential premises have received a new headache.

Charging for hot water supply consists of two parts, or components, each of which is highlighted in a separate line on the receipt - DHW and DHW heating. This is due to the fact that in Academichesky houses, water preparation is carried out directly by the management company in individual heating points of each house. In the process of preparing hot water, two types of utility resources are used - cold water and thermal energy.

The first component, the so-called

DHW supply- this is directly the volume of water that passed through the hot water supply meter and was consumed indoors in a month. Or, if the readings were not taken, or the meter turned out to be faulty or its verification period has expired - the volume of water determined by calculation according to the average or standard for the quantity prescribed.. The procedure for calculating the volume of hot water supply is exactly the same as for To calculate the cost of this service, the tariff for cold water is applied, since in this case it is cold water that is purchased from the supplier.

The second component

DHW heating- this is the amount of thermal energy that was expended to heat the volume of cold water provided to the apartment to hot temperature. This amount is determined based on the readings of the common house heat energy meter.

In general, the fee for hot water supply is calculated using the following formula:

P i gv = Vi gv × T hv+ (V v cr × Vi gv/ ∑ Vi gv × T v cr)

Vi Guards- the volume of hot water consumed during the billing period (month) in an apartment or non-residential premises

T xv- tariff for cold water

V v cr- the volume of thermal energy used during the billing period for heating cold water at independent production hot water management company

∑ Vi gv- the total volume of hot water consumed during the billing period in all rooms of the house

T v cr- tariff for thermal energy

Calculation example:

Let's assume that hot water consumption in an apartment for a month is 7 m3. Hot water consumption throughout the house is 465 m3. The amount of thermal energy spent on heating hot water according to a common house meter is 33.5 Gcal

7 m 3 * 33.3 rub. + (33.5 Gcal * 7 m 3 / 465 m 3 * 1331.1 rub.) = 233.1 + 671.3 = 904.4 rub.

Of which:

233.1 rub. - payment for actual water consumption (DHW line in the receipt)

671.3 - payment for thermal energy spent on heating water to the required temperature (DHW heating line in the receipt)

In this example, 0.072 gigacalories of thermal energy were spent to heat one cube of hot water.

IN the value showing how many gigacalories were required to heat 1 cubic meter of water in the calculation period is called DHW heating coefficient

The heating coefficient is not the same from month to month and largely depends on the following parameters:

Cold water supply temperature. IN different time During the year, the cold water temperature ranges from +2 to +20 degrees. Accordingly, in order to heat water to the required temperature, different amounts of thermal energy will have to be expended.

The total volume of water consumed per month in all areas of the house. This value is largely influenced by the number of apartments that submitted their testimony in the current month, recalculations, and, in general, the discipline of residents in submitting their testimony.

Thermal energy consumption for hot water circulation. Water circulation in the pipes occurs continuously, including during the hours of minimum water consumption. That is, for example, at night, hot water is practically not used by residents, but thermal energy for heating water is still spent to maintain the required temperature of hot water in heated towel rails and at the entrances to apartments. This figure is especially high in new, sparsely populated buildings and stabilizes as the number of residents increases.

The average values of DHW heating coefficients for each block are given in the section “Tariffs and calculation coefficients”

With the arrival of cold weather, many Russians are concerned about how to pay for utilities. For example, To How to calculate hot water and how often you should pay for these services. To answer all these questions, you first need to clarify whether a water meter is installed in this home. If the meter is installed, then the calculation is made according to a certain scheme.

The first thing you need to do is look at the receipt for housing and communal services that came last month. In this document you should find a column that indicates the amount of water consumed for the last month; we will need figures with indicators at the end of the last reporting period.

The first thing you need to do is look at the receipt for housing and communal services that came last month

After these readings are written out, they should be entered into a new document. In this case, we are talking about a receipt for payment for housing and communal services for the next reporting period. As you can see, the answers to the questions of how to calculate the cost of hot water using a meter and how to determine its consumption are quite simple. It is necessary to take all water meter readings promptly and correctly.

By the way, many management companies themselves enter the above information into the payment document. In this case, you won’t have to look for data in old receipts. You also need to remember that in situations where the water meter has just been installed and these are the first readings, the previous ones will be zeros.

The initial readings of some modern meters may contain some other numbers rather than zeros

I would also like to clarify that the initial readings of some modern meters may contain not zeros, but some other numbers. In this case, in the receipt in the column where you need to indicate the previous readings, you need to leave exactly these numbers.

The process of searching for previous meter readings is very important if you need to understand the question of how to calculate hot water according to the meter. Without this data, it will not be possible to correctly calculate how many cubic meters of water were used in a given reporting period.

So, before you start studying the question of how to calculate the cost of hot water, you should learn how to take water meter readings.

Symbols on the meter

Almost all modern meters have a scale with at least 8 digits. The first 5 of which are black, but the second 3 are red.

Important

It is important to understand that only the first 3 digits, which are black, are displayed on the receipt. Because these are cubic meters data, and it is based on them that the cost of water is calculated. But the data that is colored red is liters. They do not need to be indicated on receipts. Although these data make it possible to estimate how many liters of water a particular family consumes over a certain reporting period. In this way, you can understand whether it is worth saving on this benefit or whether the consumption is within normal limits. And of course, you can determine how much water is spent on bathing procedures, and how much on washing dishes, and so on.

It is important to understand that the receipt displays only the first 3 digits, which are black.

To correctly understand how to calculate the tariff for hot water, you should know on what day of the month the readings of this device are taken. Here, you need to remember that water meter data must be taken at the end of each reporting period, after which it must be transferred to the appropriate authority. This can be done through phone call or via the Internet.

On a note! It should be remembered that the figures are always indicated at the beginning of the reporting period (that is, those that were taken last month) and at the end (these are those that are being taken now).

This regulation is prescribed in the Decree of the Government of the Russian Federation dated May 6, 2011, number 354.

How to calculate the service correctly?

It is no secret that the legislation of our country is constantly changing, and therefore citizens are beginning to worry about the question of how to calculate hot water or any other utility costs.

If we talk specifically about water, then we should take into account the fact that payment consists of certain components:

indicators of a water meter, which is located in the room and controls the flow of cold water;
indicators of the meter, which shows the consumption of hot water in a given apartment;
indicators of a device that calculates the cold water consumption of all tenants;
data from the meter that monitors the consumption of the residents of the house; it is installed in the basement of the house;
the share of a specific apartment in the total expense;
the share that corresponds to a specific apartment in this building.

The penultimate indicator is the most incomprehensible, although in fact everything is quite accessible. It is taken into account when determining the amount of resource that was spent on everyone. It is also called “general house needs”. This, by the way, also applies to the last indicator; it is calculated when general house needs are calculated.

Calculation of hot water consumption

As for the first two indicators, they are quite understandable. They depend on the residents themselves, because a person can choose for himself whether to save the consumption of a particular resource or not. But in other cases, it all depends on how often wet cleaning is done in the entrance of the house, on the number of riser leaks, and so on.

The worst thing about this calculation system is that almost the entire part of the general household needs is fictitious. After all, in every building there are residents who incorrectly indicate their individual indicators, or, for example, one person is registered in their apartment, but five live. Then the general house needs had to be calculated based on the fact that 3 people live in apartment No. 5, and not 1. In this case, everyone else would have to pay a little less. As you can see, the question of how to calculate hot water still needs careful research.

That is why our officials are still trying to figure out how to calculate the fee for hot water and which mechanism would be the most successful.

Do everyone have the same rates?

To save money, you should always tighten the tap if this moment no need to use water

To do this, just go to the website of the management company or just call them. Also, similar information is contained on the receipt that comes to each resident.

After this data has been found, the cost of the consumed cubic meters of resource should be calculated. Next, calculating the payment for hot water is quite simple; this is done in the same way as in the case of all other resources. You should take the number of cubic meters spent and multiply by the specific tariff.

It should be noted that today there are many ways you can save hot water consumption, thereby reducing your costs for paying for it. To do this, you can use special nozzles on the faucet; they will help you not spray water so much and control the pressure power. You should also open the tap valve not at full strength, so the stream will flow under less pressure, but the water will not fly out in all directions. And of course, you should always turn on the tap if you don’t need to use water at the moment. For example, when a person brushes his teeth or washes his hair (while his head is being soaped or his toothbrush is being lubricated, the water tap can be closed).

All these tips will help reduce the cost of paying for hot or cold water, thereby helping to correctly calculate hot water consumption.

Difference between hot and cold water calculations

Of course, this formula, as well as the one that takes into account hot water consumption, has many flaws. Due to the fact that general house indicators are taken into account, it is difficult to control where the difference went between the individual indicators of all residents and the data that was taken from the water meter installed on the house. Perhaps this is really true, and all this water was used to clean the entrance. But this is hard to believe. Of course, there are residents who deceive the state and give incorrect data, but there are also errors in the operation of the pipeline system itself (the sewer pipes in most houses are old and can leak, so the water goes nowhere).

Hot water invoice

For a long time now, our government has been thinking about how to correctly calculate hot and cold water and how to improve the existing mechanism.

For example, in 2013, our authorities came to the conclusion that it was necessary to establish standard norms for general house needs and it is this data that should be taken into account when calculating the cost of one cubic meter water. This helped to slightly restrain the zeal of our management companies and help the citizens of the country. You can find out these numbers from the management company. But this only applies to those cases where residents have entered into an agreement with the management company. If we are talking about Vodokanal, then each locality will have its own separate fixed minimum payment. And, for example, an overpayment in a given reporting period may cover expenses in the next one.

As you can see, there is a whole diagram that makes it clear how to calculate hot water heating or how to calculate how much to pay for cold water consumption.

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2017:

January-April 0.0366 Gcal/sq. m * 1197.50 rub/Gcal = 43.8285 rub/sq.m.

May 0.0122 Gcal/sq. m * 1197.50 rub./Gcal = 14.6095 rub./sq.m

October 0.0322 * 1211.33 rubles/Gcal = 39.0048 rubles/sq.m.

November-December 0.0366 Gcal/sq. m * 1211.33 rub./Gcal = 44.3347 rub./sq.m

Calculation of the cost of service for hot water supply per person in 2017:

January-June 0.2120 Gcal/per person. per month *1197.50 rub./Gcal = 253.87 rub./person.

July-December 0.2120 Gcal/per person. per month *1211.33 rub./Gcal = 256.80 rub./person.

Calculation of the cost of service for hot water supply using a domestic hot water meter in 2017:

January – June 0.0467 Gcal/cub. m * 1197.50 rub./Gcal = 55.9233 rub./cubic. m.

July-December 0.0467 Gcal/cu.m. m * 1211.33 rub./Gcal = 56.5691 rub./cubic. m

2016

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2016:

January-April 0.0366 Gcal/sq. m * 1170.57 rub/Gcal = 42.8429 rub/sq.m.

May 0.0122 Gcal/sq. m * 1170.57 rub./Gcal = 14.2810 rub./sq.m

October 0.0322 * 1197.50 rubles/Gcal = 38.5595 rubles/sq.m.

November-December 0.0366 Gcal/sq. m * 1197.50 rub./Gcal = 43.8285 rub./sq.m

Calculation of the cost of hot water supply services per person in 2016:

January-June 0.2120 Gcal/per person. per month *1170.57 rub./Gcal = 248.16 rub./person.

July-December 0.2120 Gcal/per person. per month *1197.50 rub./Gcal = 253.87 rub./person.

Calculation of the cost of service for hot water supply using a domestic hot water meter in 2016:

January – June 0.0467 Gcal/cub. m * 1170.57 rub./Gcal = 54.6656 rub./cubic. m

July-December 0.0467 Gcal/cu.m. m * 1197.50 rub./Gcal = 55.9233 rub./cubic. m

2015

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2015:

Heating consumption standard * Thermal energy tariff = cost of thermal energy for heating 1 sq. m:

January-April 0.0366 Gcal/sq. m * 990.50 rub./Gcal = 36.2523 rub./sq.m

May 0.0122 Gcal/sq. m * 990.50 rub./Gcal = 12.0841 rub./sq.m

October 0.0322 * 1170.57 rubles/Gcal = 37.6924 rubles/sq.m.

November-December 0.0366 Gcal/sq. m * 1170.57 rub./Gcal = 42.8429 rub./sq.m

Calculation of the cost of hot water supply services per person in 2015:

DHW consumption standard * Heat energy tariff = cost of DHW service per 1 person

An example of calculating the cost of a hot water supply service for 1 person with a fully equipped apartment (from 1 to 10 storeys, equipped with a sink, washbasin, bathtub 1500-1700 mm long with shower) in the absence of hot water meters:

January-June 0.2120 Gcal/per person. per month *990.50 rub./Gcal = 209.986 rub./person.

July-December 0.2120 Gcal/per person. per month *1170.57 rub./Gcal = 248.1608 rub./person.

Calculation of the cost of service for hot water supply using a domestic hot water meter in 2015:

The standard thermal energy consumption for heating is 1 cubic meter. m of water * Tariff for thermal energy = cost of service for heating 1 cubic meter. m

January – June 0.0467 Gcal/cub. m * 990.50 rub./Gcal = 46.2564 rub./cubic. m

July-December 0.0467 Gcal/cu.m. m * 1170.57 rub./Gcal = 54.6656 rub./cubic. m

year 2014

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2014:

Heating consumption standard * Thermal energy tariff = cost of thermal energy for heating 1 sq. m:

January-April 0.0366 Gcal/sq. m * 934.43 rub./Gcal = 34.2001 rub./sq.m

May 0.0122 Gcal/sq. m * 934.43 rub./Gcal = 11.4000 rub./sq.m

October 0.0322 Gcal/sq. m * 990.50 rub./Gcal = 31.8941 rub./sq. m

November – December 0.0366 Gcal/sq. m * 990.50 rub./Gcal = 36.2523 rub./sq.m

Calculation of the cost of service for hot water supply per 1 person in 2014:

DHW consumption standard * Heat energy tariff = cost of DHW service per 1 person

January-June 0.2120 Gcal/per person. per month * 934.43 rub./Gcal = 198.0991 rub./person.

July – December 0.2120 Gcal/per person. per month * 990.50 rub./Gcal = 209.986 rub./person.

Calculation of the cost of service for hot water supply using a domestic hot water meter in 2014:

The standard thermal energy consumption for heating is 1 cubic meter. m of water * Tariff for thermal energy = cost of service for heating 1 cubic meter. m

January – June 0.0467 Gcal/cub. m * 934.43 rub./Gcal = 43.6378 rub./cubic. m

July – December 0.0467 Gcal/cubic. m * 990.50 rub./Gcal = 46.2564 rub./cubic. m

year 2013

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2013:

Heating consumption standard

January-April 0.0366 Gcal/sq. m * 851.03 rub./Gcal = 31.1477 rub./sq.m
May 0.0122 Gcal/sq. m *851.03 rub./Gcal =10.3826 rub./sq.m
October 0.0322 Gcal/sq. m * 934.43 rub./Gcal = 30.0886 rub./sq. m
November – December 0.0366 Gcal/sq. m * 934.43 rub./Gcal = 34.2001 rub./sq.m

Calculation of the cost of service for hot water supply per 1 person in 2013:

DHW consumption standard

January-June 0.2120 Gcal/per person. per month * 851.03 rub./Gcal = 180.4184 rub./person.
July – December 0.2120 Gcal/per person. per month * 934.43 rub./Gcal = 198.0991 rub./person.

Calculation of the cost of service for hot water supply using a domestic hot water meter in 2013:

The standard thermal energy consumption for heating is 1 cubic meter. m of water

January – June 0.0467 Gcal/cub. m * 851.03 rub./Gcal = 39.7431 rub./cubic. m
July – December 0.0467 Gcal/cubic. m * 934.43 rub./Gcal = 43.6378 rub./cubic. m

year 2012

Calculation of the cost of thermal energy for heating 1 sq. meters of total area in 2012:

Heating consumption standard * Thermal energy tariff (supplier MUP "ChKTS" or Mechel-Energo LLC) = The cost of thermal energy for heating 1 sq. m

January-April 0.0366 Gcal/sq. m * 747.48 rub./Gcal = 27.3578 rub./sq. m
May 0.0122 Gcal/sq. m * 747.48 rub./Gcal = 9.1193 rub./sq. m
October 0.0322 Gcal/sq. m * 851.03 rub./Gcal = 27.4032 rub./sq. m
November - December 0.0366 Gcal/sq. m * 851.03 rub./Gcal = 31.1477 rub./sq. m

Calculation of the cost of hot water supply services per person in 2012:

DHW consumption standard * Heat energy tariff (supplier MUP "ChKTS" or Mechel-Energo LLC) = cost of DHW service per 1 person

January - June 0.2120 Gcal/per person. per month * 747.48 rub./Gcal = 158.47 rub./person.
July - August 0.2120 Gcal/per person. per month * 792.47 rub./Gcal = 168.00 rub./person.
September - December 0.2120 Gcal/per person. per month * 851.03 rub./Gcal = 180.42 rub./person.

Calculation of the cost of hot water supply services using a domestic hot water meter in 2012:

The standard thermal energy consumption for heating is 1 cubic meter. m of water * Tariff for thermal energy (supplier MUP "ChKTS" or LLC "Mechel-Energo") = cost of service for heating 1 cubic. m

January – June 0.0467 Gcal/cub. m * 747.48 rub./Gcal = 34.9073 rub./cubic. m
July – August 0.0467 Gcal/cubic. m * 792.47 rub./Gcal = 37.0083 rub./cubic. m
September–December 0.0467 Gcal/cubic. m * 851.03 rub./Gcal = 39.7431 rub./cubic. m

Almost all housing conditions nowadays are equipped with water supply systems. However, not every apartment has a meter for cold and hot water supply. In such situations, the water tariff is calculated monthly depending on the number of people living in the house.

Therefore, if you count without control readings, the bills for drainage will have exorbitant amounts. We suggest that you quickly install a metering device so that payments are made correctly and without additional charges to the water meter according to the consumption of the number of liters of liquid.

To calculate the water supply correctly, it is necessary to take the readings indicated on the dial of the device. This will help clarify the exact use of liters in the allotted period. We recommend using a calculator to get accurate values.

Each device has an individual design, so each unit will differ in color and number arrangement. This principle is typical for both hot pipelines and cold water. In order to easily read the values, the water meter must be in an accessible place.

It should be noted that the readings located at the end are used for measurement. Let's say your water meter shows 000408, without paying attention to the numbers that are constantly rotating, we determine that we have used 408 cubic meters of liquid. Preliminary numbers (zeros) are intended for further readings, liters counted

How to calculate water bills

Let's perform calculations using the example of the Crimean tariff for water supply and sewerage, which then must be paid. Also, by analyzing all the data, you can find out for yourself how many liters of cold liquid were consumed. The main thing is to correctly take the values, the unit of measurement of which is considered to be a cubic meter.

In order to calculate hot or cold supplies, you will need the existing water supply tariff and meter readings. According to our data, the water meter reading is 408 units per cubic meter, the current tariff for water supply and sewerage is 17 rubles. 63 kopecks

Now we look in the payment account book for the previous water meter readings of 403 cubic meters. From the larger value we subtract the smaller one, that is, 408 units per cubic meter - 403 cubic meters = 5 cubic meters. m. We multiply the resulting difference by the tariff: 5 * 17.63 = 90 rubles. for only 5 units per cube. You can use a calculator for the procedure.

Note! The calculation of water supply and sewerage services is carried out jointly, so the tariff will seem high, regardless of the liters consumed. Every six months you will have to calculate expenses according to new tariffs.

After completing all the required calculations in the cube, we take the water payment book and go to the nearest bank where utility bills are accepted in order to pay for the services. You can also make payments via terminals and the Internet. We advise you to note that the tariff for supplying hot and cold water changes once every year or six months, so it is recommended to periodically familiarize yourself with the price of water.

Excerpt from legislation or how to pay for water by meter

Let's consider how many nuances there are when calculating the liters by which you can pay for drinking liquid in an apartment or private house. To date, these data have already been approved, but are quite far from ideal. Therefore, in different regions, such a calculation may vary in amount.

Basically, the amount we receive in the receipt is measured from the following terms:

For an apartment with cold water, you often have to pay for hot liquid suitable for drinking and separately for bathing, which can be labor-intensive to calculate on your own. Here, payment is made for two services at the same time: when providing water supply and sanitation.

When paying incoming bills, it is recommended to save all receipts and stubs. Since if inspectors come to take readings, they have the right to demand payment receipts. A visit log must also be provided, where you will put your signature.

General building meters can be installed in entrances; when calculating the amount of cost, it is divided among all residents.

ODN: duty or whim of utility workers?

Citizens, tenants and owners of living space must pay utility bills monthly, so payments should be made regularly. The slightest delay costs a penalty for the service. Often you can find additional payment figures in the stubs.

It is noted that one must be paid by residents when living in apartment building and using community services. Payment is specified in Federal law, involving the provision of water supply and sanitation services in multi-apartment buildings residential buildings. To date, there is no compliance with the standards of liquid intended for public needs, how many liters should be used.

When providing communications for household and other needs, the organization must be guided by a special formula to determine the calculation for one. Often, payment for such a service is calculated for each residential area individually. This will also be affected by whether the house has a water meter.

It is necessary to take the correct readings as shown by the general building meter and subtract the volume that was consumed by non-residential apartments, apartments that calculate payment according to the standard and premises that have an installed meter.
The number of cubic meters that was obtained for use for general house needs is multiplied by the area of a certain apartment and divided by the area that constitutes all residential and non-residential premises in an apartment building. Such conditions are also established for hot water if it is supplied to the house.

Standard consumption for each individual region is approved by the regional administration and government. The price is set depending on hot and other types of collateral. Ultimately, the receipt indicates the tariff at which everything needs to be calculated.

What exactly do you have to pay for?

Now the requirement to pay for general house needs often causes confusion among residents. In this section we will try to figure out what the calculation for the service one for hot and cold water supply is. If this requirement is not met, housing and communal services workers have the right to remove the meter and seal the pipeline.

In the matter of providing water, a similar combination of letters refers to such general house needs as washing floors and stairwells between floors, washing courtyards and windows. Watering front gardens in the courtyard area and caring for lawns is also included in the water supply tariff for one person.

For example, residents apartment building decided to clean the area themselves, water land, monitor the condition of the entrances, and also fulfill other needs. They should first be calculated. For all this, a certain consumption of liquid (possibly a certain number of hot liters) is used for general house needs. There is a certain standard for how many cubes there should be.

Typically, for one, a separate water intake valve is used, on which a liquid metering and control meter is installed, on which the entire expended volume is recorded, and as a result, a calculation is carried out.

Is it possible to reduce water consumption and payment for one?

The method of correctly saving water for general household needs always exists, but each individual case has its own rules and principles, regardless of what the tariff for the service will be. As for one, then you can follow these recommendations:

When living in an apartment building where cold water is used, try to insist that each apartment owner has a water meter; it is also necessary to demand from companies providing water supply services and joint sanitation if necessary