How to easily clean the toilet, remove rust and limescale? How to wash the toilet properly

It is necessary to take care of the cleanliness of the toilet to maintain an aesthetic appearance and for hygienic purposes. Pollution and damage should be removed in a timely manner so as not to suffer later, trying to remove difficult stubborn stains. Cleaning the toilet at home is easy if you know what products are needed from different types raid.

Causes of toilet contamination

Due to hard water, rust and malfunctions, plaque forms on the toilet

The toilet bowl usually gets dirty for the following reasons:

Limescale, which is formed due to the content of mineral salts and silicon in the water.
Urinary stone, which is the most difficult to clear. Substances contained in urine are resistant to detergents and have a high strength.
Rust. Often appears due to water quality, which may not be good enough if you live in a house with old plumbing.
Tank malfunction. A constantly running jet leads to the formation of yellowness.

Cleaning the toilet is half the battle. It is important to try to eliminate the reason why it got dirty, otherwise you will soon have to fight the yellow coating again.

Cleaning from different types of pollution

Plumbing should be washed at least once a week. For cleansing, a sufficient amount of products is produced, using them regularly, you can easily maintain cleanliness and shine.

The surface of almost all toilet bowls is covered with a glaze similar to enamel. It is very resistant and withstands most cleaning products well. But should not be used for washing too hot water so that cracks do not appear on the surface, in which dirt and microbes will accumulate.

It is best to remove plaque from the toilet with non-abrasive products that can leave scratches. To wash the surface, you need to use a brush of medium hardness or a brush.

Cleaning a not-so-dirty toilet is easy. Need to pour inside disinfectant. Leave it for a while for it to take effect, then rub it well with a brush and rinse.

Removal of contaminants in a place where water

To clean the inside of the toilet, the water must be removed from it.

To wash the toilet inside, where the water is, you need to flush it, and scoop out the rest disposable glass or a special device. Treat the contaminated area with a cleaning agent and wait for about an hour. Then scrub the stains, then walk with a brush and rinse with water.

Limescale removal

Best for limescale removal strong drugs with acid. You can use battery electrolyte. Its composition includes distilled water and sulfuric acid, which has a strong detergent quality and is able to remove even stubborn dirt.

To remove plaque, you should pump out the water from the toilet, process inner surface preparation, leave for half an hour, if the pollution is very strong - for 2-3 hours. Then rinse with water. It is better to wash the surface several times. If after the first treatment the plaque was not completely removed, the procedure should be repeated.

Car electrolyte can be used to clean a very dirty toilet bowl. But you need to work with it only with gloves, so as not to damage the skin of the hands with acid.

How to remove a urinary stone

Whiteness removes urinary stone well. It is necessary to pour a bottle of the product into the toilet, after removing the water, and leave for 12 hours. In the morning, wash well with a brush and rinse. Instead of Whiteness, you can use products specifically designed for cleaning the toilet. They work more efficiently and faster.

Blackness Removal

In case of old pollution, you will have to use acid or strong cleaning agents. Therefore, you should wash the device as often as possible for prevention purposes. To wash the blackened toilet bowl will help special tablets that are placed in the tank or glued next to the hole where the drain comes from. In addition to the cleansing effect, they are disinfectant and deodorant and fill the toilet with a pleasant smell. Well eliminate black plaque and rust, help prevent the formation of urinary and calcareous stones.

Toilet clog cleaning

Strong blockage can only be removed with a special cable

Sometimes the toilet becomes clogged, resulting in poor drainage. To clean your device, follow these steps:

In case of light blockage, pour a bucket of boiling water into the toilet bowl. You need to do this quickly to get a strong pressure.
Good for removing blockages baking soda. You need to pour half a pack, let stand for a while, then rinse and clean the toilet with a brush.
You can clean your device with chemicals, such as "Mole". They perfectly dissolve dirt and quickly cope with the cork.
You can break through the blockage using a plunger.

If you cannot fix the problem yourself, you should use the services of a plumber. He will remove the cork with a special cable.

Tank cleaning

The composition of the water includes mineral salts, which are deposited inside the tank and eventually damage its parts. You need to turn off the water and remove the cover. Open the tank if necessary. Treat all its components and walls with special means: Domestos, Cillit, Tyron. With light pollution, you can use the usual Whiteness. Then assemble everything and set it in place.

If you don’t know how to disassemble the tank, study its diagram, which should have been issued along with the product passport upon purchase.

Toilet bowl cleaners

You can clean the toilet in a couple of minutes so that it shines like new with the help of household products. Chemistry, like acid, will help to clean well old toilet with embedded contaminants. The most famous drugs include:

Domestos;
Toilet duck;
comet;
Cillit;
Sanox Ultra;
Sanita Gel anti-rust;
Sarma Gel.

Before buying a drug, read the instructions for what kind of pollution it helps.

Folk methods

Although there are enough household preparations to help clean the toilet bowl white at home, improvised means can be used for this purpose. They do not harm the health and family budget. In addition, they have good cleaning qualities, thanks to which the toilet will sparkle. Applying certain rules folk remedies you can achieve an effect no worse than using chemistry.

Vinegar

Heat to 50°C and add 1 tbsp. l. soda for greater efficiency. Then remove the water from the toilet bowl and cover the contaminated area with napkins soaked in the solution. Leave for 2-6 hours depending on the degree of contamination, then remove the remaining plaque. You need to scrub them with a plastic scraper or brush.

Soda

Thanks to soda, you can remove dirt and whiten the toilet bowl. Places of plaque should be treated with powder. Do not rinse, but leave overnight to allow the cleaning agent to dissolve the dirt. In the morning, rub the surface of the plumbing with a brush and rinse with water.

Coca Cola

3 liters of Coca Cola will easily remove plaque from the toilet

Washing with cola helps to remove plaque and blockages in pipes. It is necessary to drain the water, pour in soda and leave overnight. It is recommended to pour about 3 liters of cola. Then rinse and clean the surface with a brush, removing any remaining dirt.

Lemon acid

Using citric acid, you can wash the toilet so that it becomes snow-white. To do this, you need to apply the powder on the surface of the device, especially on dirty places and leave it for 2-5 hours, preferably all night. Then clean with a brush and rinse.

It is not necessary to process the toilet from the outside, it is enough to wash the outside clean water with a little lemon.

Oxalic acid

You need to work with this powder with gloves. Apply the product to a moistened sponge and rub the place of contamination well. Leave for an hour, then clean with a brush and rinse with water.

Prevention of pollution on the toilet

A bottle in the toilet bowl will reduce the amount of water during flushing

Types of pollution

The main problem that people face in their bathrooms and toilets is the yellowness of plumbing and its sloppy appearance. It also forms ugly smudges of dirt, a crust of limescale, traces of corrosion and biological contaminants.

Do not stop cleaning regularly and do not leave plumbing in a state of disrepair, otherwise you will have to work very hard to get rid of many problems. Sometimes plumbing just has to be thrown away.

Long-term operation of the toilet bowl entails the formation of limescale and urinary stone, which are extremely difficult to remove. Therefore, in the arsenal of fighting a urinary stone, you should always keep a few effective ways removal of such contaminants.

Fortunately, modern plumbing pleases its consumers with new technologies, becoming ergonomic, aesthetic and simple. Not so long ago, the plumbing market was conquered by "smart plumbing" with infrared sensor and auto flush. But unfortunately, even these innovations are not immune to problems with pollution and stone formation.

Limescale, like stone, is associated with exploitation and does not manifest itself immediately. Only at the end of a long time under the rim of the toilet bowl and in the places where the water is drained, an unaesthetic plaque becomes noticeable. That's why it is important to clean the toilet as often as possible, this will relieve years of plaque accumulation, and the removal of urinary stone will not be so problematic.

Urinary stone accumulates over the entire surface of the toilet due to the deposition of salts. Over time, it becomes impossible to clean it with a regular brush or brush. Limescale on the walls of the toilet bowl, an unpleasant smell - a consequence of the rare cleaning of the toilet bowl and its unsanitary conditions. Therefore, to avoid unnecessary expenses and keep plumbing clean, you need to get rid of deep problems first:

Eliminate all leaks from the drain tank. To avoid overfilling the tank, you just need to adjust the float. And in some cases, you need to completely replace the tank with a new one.
Adding water softener tablets to the drain tank will help to avoid further problems with odor and urinary stone.
At least once a week, it is necessary to clean the toilet bowl with an antibacterial agent. It will be enough to apply it on the walls of the toilet, brush a little and rinse with water.

Some owners prefer not to wage a "war" with such problems and decide to purchase a new toilet. But fortunately, there are many ways that will allow you to easily remove raids and save the family budget. Each method of cleaning the toilet should correspond to the degree of its contamination.

What can be washed?

With ordinary pollution can be easily and quickly dealt with Domestos or "Toilet Duck" only if they are used regularly. To avoid the appearance of traces of a urinary stone, you should clean the toilet from yellow plaque with your own hands at least once every seven days.

Take care of your toilet and wipe the plumbing with a washcloth and special detergent or regular laundry detergent.

Here are a few options available:

Help clean the toilet regular vinegar. It must be poured into water and left somewhere for 3 hours. After that, you just need to press the drain button. So simple and affordable way will allow you to get rid of a slight accumulation of urinary stone after the first application.
Lemon acid- another component that allows you to remove urinary stone and limescale without extra costs funds and time. two sachets citric acid fall asleep in the toilet and leave there for 3-5 hours. After that, the agent is washed off with water, and the remnants of plaque are cleaned off with a brush. If after the first cleaning the expected result is not achieved, this simple procedure should be repeated.
"White"- far from a harmless remedy, however, it is quite effective in the fight against urinary stone. A plunger removes all the water from the knee of the toilet bowl, after which a bottle of "Whiteness" is poured out, the toilet bowl is closed with a lid and left for the whole night. In the morning, you need to wash off the product several times and evaluate the result. If desired or unsatisfactory result, repeat the procedure again.

33% brine used when cleaning the toilet only if the plumbing is not made of plastic. Removal of a urinary stone with acid should only be performed with protective gloves, thereby protecting skin from possible chemical burns. Pour the dry walls of the toilet with plenty of acid, then leave for half an hour. Before washing, clean the places of contamination with an unnecessary brush and rinse several times with clean water. The method, although quite toxic, is extremely effective.
Electrolyte- another method that is prohibited if you have plastic pipes. However, the electrolyte is the most radical and effective in methods of cleaning the toilet from urinary stone. The electrolyte is simply poured into the toilet, left there for a couple of hours and washed off with water.
Perhaps in every house you can find oxygen bleach, which can also be useful in getting rid of a urinary stone. The agent is poured onto the urinary stone, then this place is intensively rubbed with a stiff brush and washed with clean warm water.

Abrasive cleaners, such as "Domestos", "Komet". Their method of application is simple, although unpleasant. All the water is scooped out of the toilet, the walls are covered with a product and rubbed with a rag or sponge until it is crystal white. The only disadvantage of this method is that the glossy surface of the toilet bowl can become rough due to the formation of scratches after cleaning with such products. And scratches, in turn, contribute to the rapid accumulation of plaque and urinary stone on the walls of the toilet.
Dry oxalic acid used more often in the chemical industry to clean the surface before the enamel coating procedure. But a small amount of such acid can successfully cope with the elimination of pollution in the toilet bowl. To do this, the substance is applied to a rag (the use of gloves is mandatory), with which the contaminated areas are wiped. Even easier is to pour the acid into the water, clean with a ruff and rinse with water.
Carbonated drinks, such as Cola, Sprite. Although the purpose of these drinks does not at all imply cleaning the toilets, but as practice has shown, they cope with this task quite well. Only after that it becomes scary for what these drinks can do to the human stomach. A couple bottles of sparkling water poured down the toilet. Due to the content of citric acid in the drink, plaque corrodes extremely quickly.

It must be remembered that a new and expensive toilet is much easier and more profitable to keep clean. Do not forget about prophylactic agents that can clean the drain from all kinds of raids and deposits.

No need to pour and throw away food debris, garbage into the toilet, thereby reducing the service life and drain system, and the operation of the toilet in general, and sometimes it is even fraught with blockage in the general sewer system.

How to get rid of blockage?

If you notice that the toilet has become reluctant and problematic to flush even a small amount of household waste, then most likely it is simply clogged, and you risk flooding the neighbors from below. The water from the drain can rise from the inside to the rim of the toilet bowl and pour out onto the floor of the toilet. The water will of course contain fecal particles, wet wads of toilet paper, etc.

What to do in such an emergency? Do not write off the conclusions and do not panic. It is not necessary to immediately contact the Housing Office. First, try to do all the dirty work yourself, for example, with the help of the good old air vent.

They used it even when no one heard about imported products like "Tiret" or "Komet". The wad of debris was simply pushed deep into the sewers.

Nowadays, a different method is much more effective. With the help of acid, the lump of debris dissolves, and thus the blockage is eliminated. He will go on his own sewer pipe with water flow.

Pump out the water, but not completely. Let there be a little bit left inside. Pour half a pack of baking soda down the drain. With the help of pushes of the air vent, we push the baking soda further into the sewer and pour one glass of table vinegar into it.

Pipes tired of clogging will only be happy with such a “cocktail”. The chemical reaction takes about twenty minutes. Then you need to pour about one and a half to two liters of boiling water into the toilet drain. The result is guaranteed.

You can also remove the blockage with the help of household chemicals for cleaning various pipes, for example, it may be familiar from childhood "Mole". Foreign "Tiret Turbo", "Debucher" are also good. Sometimes, when the blockage is small, it will be enough to pour 2 liters of Coca-Cola into the drain. True, it is not always at hand.

Nevertheless, in the difficult fight against blockage, all means are good. At home, you can correctly and quickly get rid of the blockage by using the means recommended by us.

Cleaning methods

There are several effective ways to wipe off pollution:

Bring kitchen vinegar to forty degrees, then pour baking soda into it, mix well. Apply the resulting gruel to the dirt and leave it there for ten hours. Clean up at night.
Citric acid has long been successfully used by many housewives to successfully clean their toilets and bathrooms. Take a couple of sachets of this acid, sprinkle the contaminated areas. Make sure that the citric acid covers the dirt completely. After two hours, wash and rinse the toilet with a large number hot water.
Sprinkle ethanedioic acid on urinary stone and limescale. Wait two hours. Then you need to wash the toilet with warm water.
Flush all the water out of the toilet. Then throw a few liters of Coca-Cola into it. Leave sweet water to sleep in your toilet bowl. Just do not immediately drain the water! This will have to be done in the morning. Then, at the same time, wash the walls of the toilet bowl with a brush.
A simple baking soda will help you remove the limescale. Take a pack of soda, pour it into the toilet and leave it for 30 minutes. Then pour table vinegar into it. You will see a chemical reaction between substances. Then scrub the toilet with a brush.

The result will pleasantly surprise you. Be sure to regularly wash and clean the bathroom and toilet in your apartment. Then they will remain in excellent condition for many more years.

In order not to face every day with the problem of getting rid of urinary stone, limescale, unpleasant smell in the toilet, you need to monitor its cleanliness. Remove all deposits in the drain tank. This procedure should be carried out at least once every six months.

Here are some tips to help you keep your toilet clean:

Use cleaning gels that have bleaching and disinfecting properties.
Wash the toilet not only from the inside, but also from the outside. To clean the toilet, use a special brush. Keep the toilet brush in perfect cleanliness. As it gets dirty, buy a new one from the store.
You can easily clean the toilet in hard-to-reach places with your old toothbrush. The lid and seat of the toilet are wiped with paper napkins or a piece of dry toilet paper.
Fill the neck of the toilet with a special washing gel and leave it there for half an hour. You need to do this in order to get rid of all the dirt. Then scrub the dirt with a toilet brush. Clean the drain with a special gel. Always wear rubber gloves, this will protect the skin of your hands.
For external cleaning of the toilet, use napkins or paper towels. Pour required amount disinfectants, soak a towel and wipe the sides of your toilet.

Every housewife dreams of her house shining with cleanliness. But the modern life of women does not always provide this opportunity. Work, children, family - now there is absolutely no time for cleaning. If the toilet is not cleaned for a long time, a urinary stone may form on its surface. A urinary stone is a build-up of minerals that, along with urine, get on the walls of the toilet. Usually, a urinary stone forms under the rim of the toilet, as well as in the place of stagnant water.

Why does a urinary stone form?

Most often, a urinary stone is formed on the toilets with untimely and insufficient draining. This is especially true in families with small children. Babies don't always remember to flush and the minerals from the urine eat into the walls of the toilet bowl.
If the drain barrel is defective, this also contributes to the formation of limescale and urinary stone.
Plumbing with a defect or a rough surface is an ideal place for the accumulation of dirt, germs, plaque and stone.
Old toilets with a long service life are most prone to the formation of urinary stone.

The urinary stone tends to grow and increase in size. If you do not fight it, it significantly narrows the lumen of the toilet bowl and pipes. Therefore, if you are faced with such a problem, you do not need to delay its solution. With a urinary stone, you need to fight here and now!

First you need to drain the water from the toilet. This is easy to do with a mug with a handle - just scoop out the water. After all, any tool works much more effectively without water.
Then put on gloves and a respiratory mask. Most modern chemicals quite aggressive.
Take any cleanser that says on the label that it can fight urinary stones. For example, Toilet Duck, made from hydrochloric acid, is very effective even in still water. In the line of household chemicals Domestos there is a special tool designed specifically for urinary stone. According to the manufacturer, this tool completely destroys even chronic one-year-old growths. Very effective in the fight against urinary stone and Cillit, its effectiveness is noted by many housewives. Another powerful household cleaner is Mr. Muscle in granules. It not only cleans the toilet from urinary stone, but also whitens the surface. The choice of professional household chemicals is up to you.
Apply the product of your choice to the rim of the toilet bowl and to the places where the urinary stone has grown. Leave for a couple of hours. You can't use the toilet during this time.
After the indicated time, rub the walls and rim of the toilet with a brush. It is better not to use metal brushes, they can scratch the plumbing, which leads to the re-formation of plaque.
Of course, it will not be possible to get rid of a dense and thick coating at a time. If necessary, the procedure can be repeated. Thus, over and over again, you will get rid of the thickness of the urinary stone until you remove it completely.
Please note that children and animals must not be in the bathroom during treatment. Chlorine-containing household chemicals highly toxic.

How to get rid of a urinary stone with improvised means

If there are no specialized gels at hand, you can use what you have at home. Here are a few effective ways getting rid of urinary stones.

Vinegar. This is a great recipe for removing a urinary stone. For this we need vinegar, baking soda and iodine. These ingredients can be found in every home. A glass of vinegar must be slightly warmed up. Take not very strong, 9% is usually enough. Be careful - do not inhale the vapors of the heated liquid. After that add to hot vinegar a spoonful of baking soda and a teaspoon of iodine. Mix the composition and pour it into the toilet. It is best to do this at night so that the prepared remedy has time to take effect. In the morning, go through the toilet with a brush and rinse everything thoroughly.
Bleach. This is a very aggressive and very effective remedy for fighting urinary stone. However, it does not work in water, it must first be scooped out. Pour a glass of any chlorine bleach and leave for a few hours.
Lemon acid. This is another effective way to get rid of plaque. You don’t need to do anything, just pour 3-4 sachets of citric acid into the toilet. Leave for a while. This will not completely remove the stone, but small growths can be easily removed.
Bleach. Buy a bag of bleach and pour it down the toilet. It is best to leave the product overnight. Chlorine not only helps to destroy the stone, but also disinfects the surface, which is also important. In addition, after chlorine-containing products, the toilet bowl will again shine with whiteness, like new.
Anticalc. This universal remedy to remove any type of plaque - scale, urinary stone, calcareous formations. Pour a packet of this powder down the toilet at night. In the morning you will find that the urinary stone has begun to fall off by itself, right in pieces. Residues of dirt will need to be cleaned with a brush or brush.
Oxalic acid. This tool is suitable for hard-to-remove and chronic growths. Oxalic acid can be bought at hardware stores, it is a powder white color. When using oxalic acid, it is very important to wear a respirator and gloves, as the agent is very toxic and corrosive. If the urinary stone is localized only at the drain site, the acid must be poured into the water. If the stone has formed on the rim of the toilet, you need to put a little powder on a cloth and gently wipe the contaminated areas. Leave the toilet for a while, then once again walk on it with a brush and press the drain button.
Carbonated drinks. This is a modern, but very effective means of getting rid of urinary stones. Take a couple of bottles of Coca-Cola, Sprite or Fanta and pour it down the toilet. Leave for three to four hours. A high concentration of citric acid breaks down the stone and cleans the toilet bowl.
Electrolyte. This is the most thermonuclear remedy for urinary stone. The electrolyte is used in car batteries, but it perfectly destroys various kinds of growths. However, before use, make sure that all pipes in your sewer system metal. plastic pipes may be damaged. So, pour some electrolyte down the toilet and let it sit for a couple of hours. After that, proceed similarly to the previous methods - clean and rinse.

It is worth noting that urinary stone appears on running plumbing when the toilet is not cleaned for a long time. Therefore, in order to avoid such growths, you need to regularly, at least once a week, clean the toilet bowl with prophylactic agents. Any household chemicals will cope with a small amount of pollution. To do this, just pour a little chlorine-containing product on the rim of the toilet, and then rinse everything with water.

Also pay attention to the serviceability of the drain tank. If the water flows constantly, it contributes to the formation of calcareous and urinary stones. This is especially true in regions with hard water. To soften the water, you can put a small filter in the tank that will protect the toilet from various kinds of growths.

An excellent prevention of the formation of urinary stone are special plates and tablets that are attached to the inner wall of the toilet bowl. With each drain, the surface is cleaned and disinfected, which is important for general hygiene.

As noted, urinary stone is formed on rough surfaces, in places of chips and cracks. To avoid this, you need to protect the surface of the toilet and do not clean it with abrasive products. Do not pour the remains of hot food into the toilet bowl - it can cause the formation of microcracks.

An old, damaged toilet is a potential site for a urinary stone to build up. Having eliminated it once, be prepared for its reappearance. To avoid constant struggle, you need to buy and install a new toilet with a glossy surface. Monitor its condition, clean its surface regularly, and urinary stone will not bother you anymore!

Video: how to wipe the toilet in 15 minutes from a one-year-old urinary stone

Maintenance toilet room in its purest form - the guarantee of your health. Various harmful microscopic organisms can disturb our inner balance and cause various diseases. Now the chemical industry offers wide choose toilet care products. The main thing is to choose the right one and follow the instructions for use.

Features of care

Regardless of the material your toilet is made of, it needs to be cleaned. It should be done at least twice a week, but it is advisable to keep this sanitary ware clean every day, especially if you have small children. Consider the options for caring for the toilet, depending on the material of manufacture:

Porcelain toilet. Alkaline and acid cleaners are suitable for its cleaning. Abrasive and powder are not suitable here, since the applied product needs mechanical action, and this can simply scratch your toilet bowl.
Ceramic and faience toilet bowls. The ideal cleaning agent is hydrochloric acid solution. Never rub the toilet metal brushes. This causes scratches. Exposure to boiling water is also unacceptable. The toilet will just crack.
Toilet made of polymer concrete. Liquid products, various gels are suitable for cleaning it.
Toilet bowl made of stainless steel. This product is resistant to physical influences, so a brush with soft bristles and any chemical agents are suitable for cleaning: abrasive, powder, alkaline, acid. You can use boiling water.

Mounted cleaners

Mounted toilet bowl cleaners include special gels, tablets that are suspended in special device to the place where water enters the drain part of the toilet bowl. Mounted cleaners perfectly cope with limescale, disinfect and give a pleasant aroma to your toilet.

Do not forget to change plastic containers for gels at least once every two to three months. If you have no desire to wash them periodically - buy containers that are disposed of after the cleaning filler runs out.

Tools and chemicals

Any cleaning of the toilet bowl is impossible without a brush, sponges and rags. Please note that the brush should not have very coarse bristles. Otherwise, it may cause scratches that cannot be removed later.

To clean your toilet bowl with alkaline products, drain the water from the toilet bowl and apply the product with a sponge to the inside products. After 10-15 minutes, the product is washed off with water. If necessary, repeat the procedure.

When using chemical acidic or alkaline products, cleaning is mandatory with rubber gloves, and sometimes glasses.

Folk remedies

A wonderful folk cleanser is the usual baking soda. It is enough to sprinkle it on contaminated places and leave for a while. Next, the surface treated with soda is poured with a solution of vinegar and lemon juice. What happened chemical reaction disinfects and cleanses at the same time inner part toilet. There is no trace of bacteria left.
Acetic solution can be left overnight. This will give freshness and whiteness to the product, remove the rusty coating that arises from constantly oozing water. Vinegar can be replaced with citric acid.
Another interesting folk discovery in terms of cleaning toilets is world-famous Coca Cola drink. It gives whiteness to the surface. Just pour a bottle of soda down the toilet and let it sit for a few hours.

Removal of stone and limescale

Prevention of limescale removal is surface treatment soapy water. If limescale has already shown itself, then use 96% slightly warmed vinegar essence. It should be applied to the places of plaque accumulation and left for a short time period. Then rinse with a sponge.

Store shelves are full of various means that help get rid of this unpleasant phenomenon. They act effectively and quickly, within 10-15 minutes. Special tablets that are placed in the drain tank help get rid of stone and limescale. Acid solutions also remove these unpleasant phenomena well.

In any case, weekly cleaning of the toilet bowl prevents the formation of stone and plaque. So don't forget about it!

You will have much less problems with the care of the toilet if you install a "smart" toilet with a self-cleaning function. It's not cheap, but the novelty is worth it!