Several tricky tricks for home craftsmen were posted on his video by the author of the Stroykhak channel.
1. If you are the lucky owner of a usually mechanical tape measure, masking tape will come to your rescue. Stick it on the tape measure and you don't have to constantly run to the table to write down the results. All this can be done right on the roulette wheel. And then transfer it to paper. Or just stick the tape itself.
Tricky Tape
2. To keep the spatula clean, for example, when working with some dirty chemicals that are then difficult to tear off the tool, use a strong household tape. This is a very handy little trick. Strong and at the same time easily torn across. Stick on the spatula and it will always remain clean after work. The household tape is removed without leaving any traces. This technique is very useful when working with bituminous mastic, for which the spatula has to be washed with a solvent. By the way, customers perfectly seal the spouts of building tubes, there is no need to tighten different self-tapping screws. Only it is better to stick with an offset edge. This makes it easier to shoot later.
Cellophane helps out
3. Often the pva glue dries on the threads of the bottles it is in. Unscrewing the lid next time is very difficult. To prevent this from happening again, take a plastic bag and cut a small piece out of it. The thread is now secure. And the glue bottle will always be easy to open.
Circular saw attachment
4. The circular saw has several nozzles of different diameters. But all of them periodically have one problem: when drilling a hole, a wooden circle remains, wedged inside the saw, it can be very difficult to get it out of there. Of course, you can use a screwdriver, but it is more convenient to use a screw by screwing it into a piece of wood. And he, resting on the base of the saw, will complete the problematic remainder. Useful trick for home master.
Plastic pipe clamp
5. If you have a piece left plastic pipe from repair, it will make an excellent clamp for various wires and cords. Cut off a few centimeters with any tool. Hacksaw or special drill 2 through holes. It is convenient to make small diameter drills first, and then a little larger. For example, the master has a drill with a diameter of 5 mm. The edges of the cut part can be turned on sandpaper. We take an elastic band, stretch it through the hole and tie knots at the ends. The device is ready. A bunch of old naughty wires will now be in order.
Trick for comfortable drilling
6. Masking tape is useful to us in one more case. When you need to make holes on the wall for some gadget. For example for a phone. Glue on the device and with a simple pencil manifest seat for fastening. We remove the tape and mark the places for drilling. Now all that's left is to stick it to the wall. And it can be corrected. Now we make holes.
Hose to work smart
7. If you have adjustable or, as they are also called, adjustable, use the following advice. Cut off a couple of pieces from a rubber or silicone hose and put them on the jaws of the tool. Now when working with delicate surfaces, like chrome parts, do not leave scratches. In order not to lose pieces of the hose, they can be put on the tool after removing the plastic handles.
Visualization of tricks on video
Watch the video on how to apply tricks and tricks for a smart home master.
- this is folk wisdom that will help you out in almost any situation when you have a difficult situation: for example, during home repairs, car repairs, when making the thing you need, it may always not be at hand necessary tool or material.
Look around you and you will find a lot of unnecessary things from which you can benefit by showing resourcefulness and ingenuity.
An iron or cast-iron grate on a balcony must be cleaned of old paint and rust with a stiff brush made of thin steel wire, or coarse sandpaper.
The grate should be washed, and when it dries, primed. For a primer, it is best to use red lead, diluted on drying oil. When the primer dries well, you can already paint with oil paint, covering with a thin layer twice.
It is necessary to paint metal objects that are in the open air in good weather so that the paint lays on a dry surface.
Putty can be dyed any color during the manufacturing process. If the frames are painted White color, lead or zinc white is added to the putty and mixed to a working viscosity. If a lot of paint has been added and the putty has become rare, you should add ground chalk to it and knead it in your hands.
On oil and enamel paints, a sufficiently thick film forms during long-term storage. To prevent it from appearing, after finishing work on the paint surface, put a circle of thick paper, pour a little drying oil on top.
If the lid of the can where the paint is stored is lost, smear the upper edge of the can around the entire circumference with paint and cover with a piece of glass so that the paint sticks to it.
Cut a stick out of linden bark the right sizes. Steam it in boiling water, dry it well and carefully break one end with a hammer. As a result, get a brush for wood glue. You no longer have to test your patience by cleaning the brush from dried glue: cut off the end and discard it, and again break the tip of the remaining stick with a hammer to form a new brush.
So that frosted glasses do not deteriorate, are clean and have beautiful view, they are washed hot water adding a little vinegar to it.
Hands from oil paint are easier to wash if you pour mustard into the water.
In order to temporarily eliminate leaks from rusted pipes or their joints, it is necessary to tightly wrap the faulty place with waterproof material (for example, rubber, insulating tape) and secure it with wire.
Adhesive paint is used only for internal surfaces not subject to moisture, mainly on plaster. For damp rooms it is better to use lime coloring.
To beat off part of the wall, a thin cord is coated with dry paint chosen for painting the walls, pulled along the pencil marks and, taken aside, released - a trace remains on the wall.
Oil and enamel paints do not pass air well. Therefore, it is undesirable to use them for painting the walls of living rooms.
For filling the pores of the plaster, it is better to use a wooden spatula.
Grinding is performed with pumice stone on dry or wet (soaked in water) putty, as well as sandpaper.
Helpful Hints home master - the theme is truly inexhaustible. Small, simple, useful tips for a home master are often more necessary than detailed articles on one particular topic.
Guys, we put our soul into the site. Thanks for that
for discovering this beauty. Thanks for the inspiration and goosebumps.
Join us at Facebook And In contact with
For many of us, cleaning is the most burdensome duty and a terrible punishment. Often, only at the moment when there is no clean space left in the house and the apartment begins to resemble a dinosaur battlefield, we doomedly proceed to restore order. In fact, cleaning is easy and fast if you know the basic secrets.
We are in website set out to make your life easier and put together some new tricks to help you get through your homework.
Cleaning the dirtiest items in the bathroom
An old bathroom curtain will look like it came from a store if all dirty areas and even places with yellowness and mold are washed with a solution consisting of equal parts hydrogen peroxide and water.
To clean your toothbrushes of germs, soak them for an hour in vinegar. Then wash well under running water.
Soak washcloths for an hour hot water and vinegar in a 1:1 ratio. Then rinse well clean water and dry.
We wash the bath white
From limescale, yellow spots and gray surfaces, hydrogen peroxide helps well. We spray it with a spray bottle on the surface of the bath, leave for half an hour and then rinse well warm water.
You can easily clean the surface of the bath if you fill it with soda and pour vinegar after a few minutes. After that, you need to lightly brush the surface with a brush and rinse with warm water.
Undesirable yellowness is effectively removed by a solution of ordinary citric acid. We make the solution at the rate of: one sachet per glass of water. Apply this product with a sponge to the surface of the bath and leave for 20 minutes. Then wash off with warm water.
You can clean the bath to a shine and get rid of old plaque with a mixture of vinegar and salt. We mix the ingredients in a 1: 1 ratio and clean the bathroom to whiteness.
Dealing with a dirty toilet
The toilet will sparkle with cleanliness if used for cleaning mustard powder with the addition of equal parts citric acid and cornstarch.
To clean and refresh the toilet, you can make your own cleaning bombs. Just 1-2 bombs thrown into the toilet will give not only a hygienic effect, but also a pleasant smell.
You will need:
- 1 glass of soda
- 1/4 cup citric acid
- 1/2 tsp vinegar
- 1 st. l. 6% hydrogen peroxide solution
- 15-20 drops of your favorite essential oil
Cooking:
Pour soda into a bowl, add citric acid. In the second bowl, mix the vinegar and peroxide and pour this liquid drop by drop into the dry mixture. Adding essential oil and form small balls with a spoon. We spread the bombs on parchment paper and dry for at least 6 hours. We store the bombs in a closed glass jar.
We clean the seams between the tiles in the bathroom
With plain white paraffin candle you can get rid of mold, dark plaque and dirty deposits on the seams between the tiles. To do this, you need to run the dirty seam several times with the blunt end of the candle. This will clean and protect the seams from mold and dirt.
We pour baking soda into a bowl, take it with an unnecessary toothbrush dipped in water and clean the dirty places. After cleaning, rinse the surface with warm water. Seams are like new!
We mix warm water with hydrogen peroxide in proportions of 2: 1. With a brush or sponge, we clean the seams between the tiles with this solution, which then can not be washed off.
Washing tiles
We take 15 grams of citric acid and dilute it with a glass of warm water. We wash the tile with the resulting solution. Then rinse off with clean water.
When too dirty tiled walls vinegar will help. Spray the surface with a spray bottle of vinegar, leave for 10 minutes and rinse with clean water. Then wipe the tiles with a soft microfiber cloth. This method will not only wash the tile, but also disinfect it.
Fixing the washing machine
We clean the washing machine once a quarter.
Ordinary citric acid will help clean the car from scale and water scale. Pour 60 grams of citric acid into the powder compartment. We start the machine full cycle washing at the highest temperature.
Cooking simple and effective remedy, which will lead washing machine in order.
You will need:
- 2 cups of vinegar
- ¼ cup baking soda
- ¼ glass of water
- sponge
Cooking:
In a bowl, mix water and soda. Pour this solution into the powder compartment. Vinegar is poured into the drum washing machine. We start the machine in the normal washing mode. After the cycle is completed, wipe all rubber gaskets and the door with a sponge. Dry the drum with the door open.
Perfectly wash the stove
We remove fat from the surface of the plate and from small parts with an ordinary eraser. This method is used by employees of professional cleaning services.
A greasy stove can be tidied up with lemon juice and lemon wedges. Squeeze out the juice, wipe the stove with lemon and leave for 15 minutes. Then wipe with a wet cloth.
Cleaning the oven
You can clean the oven from fat and soot with a glass ammonia and a liter of water. Heat the oven to 150 degrees and turn off. We put a container with hot water on the lower grate, a container with ammonia on the upper one. Close the oven door and leave to cool until morning.
In the morning, add a few teaspoons of any detergent and half a cup of warm water. Wipe the oven with a sponge with the resulting solution and rinse it with water.
This article, as usual, has a beginning, but by definition it cannot have an end. Tips for a home master is a truly inexhaustible topic. small, simple tips a home master is often more needed than detailed articles on one particular topic. I will try to constantly replenish the material in the presence of free time and desire, of course.
1. How to drive a nail into the edge of a board
To drive a nail into the edge of the board and not split it, it is enough to first tap the edge of the board well from above with a hammer. If the nail is thin, then you can drive it in immediately after that - the board will not crack. If the nail is thick enough, then you need to first punch the hole with a thin nail, and then drive in a thick one.
2. How to carefully pour the paint
In order not to stain it from the outside when pouring paint from one can to another, you need to install an empty can inside a plastic bag, and wrap the edges of the bag inside the can. After the liquid is poured, the bag is torn from below, removed from the can and thrown away. The bank remains clean.
3. How to hang a picture or photo on the wall evenly
To hang the picture evenly on the wall, it is desirable to have a level. If there was no level at hand, then it can be made at home from an empty transparent plastic bottle: fill it up to about halfway with water - now, no matter how you turn the bottle, the surface of the water will always be horizontal.
In order to hang a large thing on the wall - for example, a carpet - you can make a more serious water level. To do this, we take two medical syringes and a rubber or PVC tube of the required length. We connect the syringes with each other with a tube and fill the system with water. The water in the syringes will always be at the same level.
4. How to drive a screw into plastic
To securely screw a screw or bolt into plastic, the home craftsman first drills a hole smaller than the diameter of the thread into the part. Then the screw is well heated with a soldering iron or on a stove (for a small part, a lighter flame is enough). The screw will easily twist into the part and, having melted the plastic, forms a good thread.
5. How to cut plastic
It can be quite difficult to cut thermoplastic plastic with a hacksaw or a jigsaw, as the plastic melts and the blade sticks. Apply a little machine oil along the cut line, and things will go faster.
6. How to make drop-down pliers
The home handyman often has to work alone, and when working, it can be difficult to open the pliers with one hand. Connect the handles of the pliers with a piece of elastic rubber hose of a suitable diameter, and the pliers will open themselves.
7. How to collect iron filings
Collecting iron filings or small chips, of course, is easiest with a magnet. It is difficult then to clean the magnet itself from sawdust. Tip: put the magnet in before doing this. plastic bag, which, at the end of work, turn inside out - and the magnet will remain clean, and sawdust - in the bag.
8. How not to lose the spring
Springs during disassembly or assembly have a vile property: they jump out of hands, fly away and get lost. A simple tip for the home master: before starting the process, tie a thread to one of the coils of the spring - now it will not go anywhere.
9. How to bend duralumin
In order not to break the fragile duralumin when bending, I advise you to heat the bend gas burner and then grease laundry soap. Continue heating the fold until the soap layer is completely blackened - this will be just the temperature of maximum plasticity of duralumin.
10. How to increase the temperature of the soldering iron
If the temperature of your soldering iron tip is not enough, then I advise you to wrap the body of the soldering iron with a couple of layers aluminum foil. By reducing heat loss, you thereby increase the temperature of the sting.
11. How to remove an old screw
It can be problematic to unscrew an old screw from a hardboard: the slots break off. Hold the screwdriver blade with an adjustable wrench and insert the tip into the slots of the screw. With one hand, press on the screwdriver, and slowly turn the key with the other - the screw will turn out like a pretty one.
The task can be further facilitated by heating the screw - by pressing the soldering iron tip to its head.
12. How to cut plywood
The edges of plywood are often chipped when sawing. To keep the edges even and smooth, moisten the plywood with water along the cut line.
13. How to sharpen a tool
The cutting tool is sharpened faster and easier if before that it is held for half an hour in a saline solution, and the whetstone is moistened with kerosene.
14. How to clean a file from copper filings
Run a powerful, well-heated and tinned soldering iron along the notch of the file - sawdust will gather into large lumps that can be easily removed.
15. How to cut thin metal
To accurately cut a thin metal plate, clamp it in a vise between two flat pieces of wood and saw this "sandwich" as a whole.
16. How to restore an old file
To restore an oily, rusty, worn file, soak it in a sulfuric acid solution for a few minutes, then rinse well with a soda solution.
17. How to drill a vertical hole
Place a small mirror on the workpiece close to the drilling point. The drill of the tool and its reflection in the mirror should form one straight line.
18. How to cut round timber to length
In order to evenly cut a round stick along the entire length, a template with a cut in the middle can be made from a metal tube of a suitable section. First, make a cut without a template, and when the saw is deep enough, put on a template on top and saw the part to the end.
19. How to upgrade a shovel
If a dozen holes with a diameter of about 20 millimeters are drilled in a shovel, then wet earth and clay will stick to it less.
20. How to cut rubber straight
Lubricate the knife blade with laundry soap and it will be much easier to cut rubber, and the edges will be smoother.
21. How to screw in a screw in a hard to reach place
Pull a piece of rubber tube over the tip of a screwdriver and insert a screw or screw into its end.
22. How to remove a key chip from a lock
Insert a jigsaw file into the lock cylinder parallel to the key fragment, then turn the saw blade with the teeth towards the fragment and pull it out.
23. How to protect your hands from calluses
When working with an ax, a sledgehammer, a shovel and other tools, put foam rubber rings on your palms - and it will be convenient to work, and it will protect you from corns.
By wrapping the handles of tools with vinyl tape, you will also save yourself a lot of blisters.
24. How to collect small pieces of glass
Make a sausage from a piece of plasticine and roll it over the place where the glass was broken. So you will collect everything, even the smallest fragments.
25. How to extend the life of wooden tool handles
Before putting the instrument on wooden handles, boil the handles in drying oil - this will protect them from cracking.
26. How to tightly fit the chisel and chisel onto the handle
Pour a mixture of rosin and ash or sand into the hole in the handle, heat the spur of the instrument red-hot and quickly insert it into the hole. The tool will be securely fixed in the handle.
27. How to drive a nail into plaster
To prevent the plaster from crumbling, stick a piece of masking tape on the place where you need to drive a nail.
28. How to Hammer a Nail into Hardwood
Before hammering a nail into hard rock wood, lubricate the nail with soap or paraffin, and things will go much easier.
29. How to solder a massive part
If the power of the soldering iron is not enough to solder the part, place the part on the soleplate of a hot iron.
30. How to save cement
Cement in paper bags is not stored for a long time and quickly loses its properties. You can save it for several years by packing it together with paper packaging in a plastic bag, and tying it as tightly as possible.
31. How to find a deeply driven nail
Finding a deeply hammered and puttied nail - for example, in floorboards, is sometimes difficult. Magnetize the needle and drive it on a thread along the board at a height of about 1 millimeter. Above the nail, she will deviate and accurately indicate the place.
32. How to drill a small hole in glass
Sharpen a flat file on an emery like a sharp chisel. Fix in the chuck hand drill and drill slowly, periodically cooling and undermining. In about 15 minutes, you will drill glass with a thickness of 6 millimeters.
33. How to cut a thin-walled pipe
Install two blades in a hacksaw with teeth towards each other. The cutting force will be the same in both directions.
34. How to find a crack in metal
If you cannot find a crack in a metal part, paint over its surface with a chalk solution and dry it. Then drop a drop of kerosene on the search site. The crack will show up immediately.
35. How to fix the nut securely
If there is no spring washer at hand, then you can securely fix the nut from unwinding by first wrapping the bolt with plastic wrap.
36. How to protect your hands when working with solvents
Before putting on gloves for working with caustic liquids, grease your hands with a greasy cream and sprinkle with talc or baby powder. Now there will be no burn even if the glove breaks.
37. How to find holes in the wall after wallpapering
In order to find the places where the screws you need were previously screwed in after wallpapering, insert fragments of matches into the holes in the wall, leaving “hemp” 1.5-2 mm high on the surface. They will not interfere with the wallpaper sticker, but then you will find the holes without problems.
Banks will help to store things not only on the shelf, but also under it. IN glass jars very convenient to store nails, fasteners and other small parts. So that the jars do not “dangle under their feet”, they can be fixed above the head - just drill a couple of holes in the lid and screw it to the shelf with self-tapping screws. For storage, you just need to screw the jar into the lid. Good large lids usually cover jam jars.
Thanks to the hooks, the keys will not get lost in the drawer. Every house has drawer, full of rattling keys that are rarely used but cannot be thrown away. So that the keys do not rattle and do not roll under other things, they can be hung on hooks - right inside the box.
Dish drying will organize the tools. We spied this recipe on YouTube. It turns out that dish dryers seem to be specially designed for storage. wrenches. And they come in almost any size and shape and, if necessary, bend well. Therefore, dish drying can be selected for any garage drawer.
Magnetism vs Chaos
Determine the type of metal under the paint. .To drill steel, be sure to use drilling paste. In the case of aluminum, paste can be dispensed with. How to determine what kind of metal is hidden under a layer of paint? Winged metal is indifferent to magnets, while steel is attracted to them.
Don't lose small details. Small screws, nuts and washers tend to roll into places where you will never get them. It is easier to store them next to a magnet, which will easily subdue their ardor. By the way, with the help of a magnet, you can conveniently carry small fasteners in your pockets.
To pacify the butter dish dancing at the machine. The vibrations of the engine of a machine or tool can gradually and imperceptibly push off the table light oilers and spray cans that may need to be kept at hand. So that the containers do not "dance" on metal surfaces, attach a magnet with a soft rubber pad to the bottom of them.
The trash bag saves water. To carry a bucket of water without losing a drop, a simple trick will help. Place a large trash bag in the bucket and pour the liquid directly into it. Then tie the bag in a knot and run home, boldly swinging the bucket.
The jack defeats rust. Dismantle outdoor unit air conditioner, rusted to the supports, a jack will help. It can be rested against a nearby wall, window sill, or directly into the ground if the unit is hung low. As a rule, it is enough to make only a couple of turns.
The bolt and nut fix the chain. A bolt and nut of a suitable diameter is quite capable of quickly and reliably repairing a broken chain. The main thing is not to forget to remove the broken ring before this: being open, it easily bends, turning into a real “weak link”.
Left is right, right is wrong
Adjustable wrench for dummies. This has amazing handy tool only one drawback - the ability to unexpectedly slip off the nut or bolt head. This happens due to misuse. There are two simple rules: first, pull the key, and do not push it - this way your hands will be safer. Secondly, the main force should fall on a fixed sponge - a movable one under heavy load can “release” the nut. So, hold the key with a movable sponge towards you and pull it towards you.
Water pipes not visible until they leak, says folk wisdom. To communicate with plumbers, use our concise illustrated dictionary.
Food coloring will indicate a malfunction in plumbing. Condensation or dew on pipes is often mistaken for a leak. If you have your own boiler in the house, then the diagnosis is very easy. Add food coloring to the boiler and see if your "dew" is colored.
The tennis ball will bring the blanket to life. Blankets and sleeping bags become less warm over time. This is due to the fact that the air cavities, which provide heat-insulating properties, are crushed and reduced. By placing the blanket in the dryer along with a couple of tennis balls, you will fluff it up well and fill it with air again.
What is a staple? Not all office workers know the answer to this question. In the meantime, this report stapler is also perfect for storing hacksaw blades. This method will help protect your hands from cuts, and blades from blunting.
