Phone stand diagram. Do-it-yourself stand - how original homemade stands and stops are made (90 photos). Popsicle stick version

When there are cute ones in the house cozy little things, this helps create an atmosphere of warmth. Making something interesting and useful at the same time is not so difficult. Today almost everyone has mobile phone. When we return home, we most often put it on the table. It happens that we don’t notice and throw papers or other things on top, and sometimes we even lose them on the desktop. A DIY phone stand solves two problems at once: you will forever be able to allocate a place for your phone and develop the design yourself.

How to make a phone stand?

Surely you have at least one at home cardboard box. From such waste material you can create something unique. We suggest making a phone stand from paper and an old box.

To work, you need to prepare office glue, a pencil with a ruler, and a knife.

Before you make a phone stand, you need to prepare the cardboard. Cut rectangles measuring 10x20cm. We will need 9 such blanks.

Now you need to glue them together in threes.

On two we draw such a detail. This will be the side of the DIY phone stand.

Cut it out. In order for everything to be beautiful and the structure not to lose stability, you need to put the sidewalls one on top of the other and check how similar they are.

Take a utility knife and cut a hole in the shape of a rectangle.

Next, you need to make the base for the phone stand with your own hands. We measure the width of the phone and cut out a stand to fit the size of the third piece. The width of the phone is the length of our rectangle. The width of the rectangle should be such that it can fit into the grooves on the sides.

We assemble the structure. You will also need a small circle made of cardboard, its diameter is slightly less than the distance between the sides. (photo 8)

All blanks must be covered with paper. This could be a newspaper clipping or scrapbooking paper.
To make the back, take two pencils or something similar. We make holes in the sides and insert them there. We put our cardboard circle on the axle.
Your DIY mobile phone stand is ready!

Another DIY phone stand option

You can make a simpler version of this stand from cardboard.

Modern means of communication perform many functions, so there is often a need to install a gadget on desk. Easiest to purchase ready-made device in the nearest store, or you can make it yourself. There are many ways to make a phone stand from scrap materials and office supplies.

From stationery binders

Students and office workers are familiar with special clips for large stacks of papers, called binders. If you have holders, the easiest way is to make a phone stand with your own hands from them.

To do this, just connect 2 elements to each other, and bend 1 metal end towards the phone.

You can also fasten 2 binders using a piece of cardboard, and insert the smartphone into the plane between the metal ears. Despite its small size, such a device is capable of holding even a phone with a large screen diagonal both vertically and horizontally.

From Lego

If there are children living in the house, there will definitely be a plastic construction set with parts of different sizes and colors. There are no special instructions for making a phone stand; you just need to select the appropriate elements and connect them in any order. The main thing is that the design is stable and attractive.

From a paper clip

Of the many ways to make a smartphone supply, the fastest and easiest is the one that uses a simple large paper clip.

To make the device, you must first bend the clamp into a straight line. Then bend it again so that the middle part provides support for back wall, and the hook-shaped edges prevented the phone from sliding forward.

From a wire hanger

If you have a wire clothes hanger, you can make original stand for smartphone or tablet. All you need is pliers and a little patience:

First you need to bend both edges of the hanger so that they are located from each other at a distance equal to the width of the gadget. The edges are compressed with pliers until they are completely connected.
Make 2 folds at each end, about 3-4 cm in size.
At the next stage, the hook is bent at an angle of 90° and turned in the direction of the wings.
Then a hook is made at the end of the upper part, onto which the inner element of the hanger is hooked and fixed.

The design can be improved with rubber tubes, which will provide an anti-slip effect and make the product more attractive.

Shampoo bottle version

An empty shampoo bottle can be turned into a convenient and beautiful phone stand. The advantage of such a device is that it can be hung on the power supply of the charger and eliminate the risk of snagging the wires and dropping the gadget on the floor.

To make the holder you will need a plastic container of the required size, a marker and a stationery knife. First, markings of future cutting locations are applied to the bottle, taking into account the depth of the phone, the location of the holes for the plugs and the dimensions of the power supply. After the layout is carefully drawn, all the lines are cut out with a knife and the edges are cleaned. If everything is done correctly, the holder can be easily placed on the charger plug and plugged into an outlet. The gadget itself will fit freely in the bowl, eliminating the bending of wires.

To make the device look more attractive, its surface can be covered with fabric or bright paper, and painted with paint suitable for plastic. The advantage of this stand is that it is inexpensive, since it uses discardable material. Also available wide choose color range and container sizes.

Popsicle stick version

Don't rush to throw away popsicle sticks. You can also make a beautiful phone stand out of them. Depending on the project, the design consists of several elements or includes a dozen components. You can glue the sticks with PVA or glue gun. After the holder is ready, it is recommended to paint or varnish it.

From paper

One of the most common materials used to make a DIY smartphone stand is paper or cardboard. If designed correctly, the product will be quite strong.

The easiest way is to create 2 triangular blocks different sizes. One will serve as the base, the other will support the bottom end of the phone. After the blanks are completely dry, they are fixed on 1 paper rectangle.

In the world modern technologies It’s hard to imagine a person who doesn’t have a mobile phone. With the entry of gadgets into our lives, accessories also appeared, of which there are a huge variety on store shelves and on the Internet. Often, a regular holder, case and other things to add character and style to a mobile device are far from cheap. Therefore, a do-it-yourself phone stand is perfect solution for each.

Making an accessory is not at all difficult. To carry out the mission, all you need is materials, time and desire. There are many variations and techniques to help everyone do what they like best. So you should turn on your imagination and use all your ideas.

What can you use to make a stand for a mobile phone?

Making something yourself gives ample opportunities for creativity. A DIY phone stand can be made from the following materials:

paper; wood; plastic; gypsum; any natural materials. In general, you can use all the materials that are at hand. The more intricate accessories there are, the more interesting the mobile phone stand will be. You can make the most incredible accessories with your own hands that are not even on store shelves. Therefore, it is worth taking note of this option.

DIY paper phone stand

It would seem that what can be made from ordinary sheets of paper? This material would actually make a great phone stand. It’s not at all difficult to create it with your own hands. To get started, you need to prepare the following items:

decorative ornaments

A properly organized space will help you create your own phone stand in a matter of minutes. Consequently, the one who embodied it will have an excellent opportunity to become the owner of a beautiful and convenient mobile accessory.
Sequencing:

First you need to figure out what shape the stand will be. Then you need to draw templates of the required sizes on a piece of paper. Elements for the product are cut out from them. Then, carefully, according to the diagram that was previously drawn or printed from some site, we glue the necessary parts. After this, you should wait until all the elements are fixed. The next step is to connect the individual parts together. Let all the fasteners dry. After this, you can start decorating the product. At this stage, you can use various sparkles, buttons, beads and other small beautiful elements. After decoration, the phone stand can be considered ready. We created a masterpiece with our own hands. With the advent of such a device, there will never be a problem with finding a mobile phone, because it will always be in its place.

DIY wooden phone stand

There are a lot of options using which you can turn any idea into reality. Why is a wooden holder better? A phone stand made of this material competes with paper products. Wood is stronger, more stable and more durable. Truth to do wooden stand, you can’t get by with sketches and ideas alone. In this case you will also need:

special equipment; skills; ability to work with wood. Before you make a phone stand with your own hands, you should analyze your actions. If you have never worked with wood before, then it is better to rely on a paper phone holder. And if you have experience, then for work you need to prepare:

the wood from which the structure will be constructed; tools for working with wood; a diagram of the product; a felt-tip pen that can be used to draw on wood; a ruler; glue; accessories (buttons, beads, rivets); a simple pencil.

After everything necessary elements are at hand, you can begin to directly implement your plans. The work sequence is as follows:

suitable scheme

In general, making a phone stand out of wood will not be a problem. Therefore, it is worth trying to make such an idea a reality. After all, it’s much more pleasant to put your phone in a stand that you created with your own hands.

Beautiful design of a phone stand

In no case should you forget about the decor. After all, it is the decoration of even the most unprofessional and amateur product that will give it color, character and mood. Therefore, it is worth looking at what interesting accessories you have at home. It can be:

shells; buttons; rhinestones; beads; foil; colored tape.

In general, everything that is at hand and has unusual look, can be useful in the process of making a phone stand.

Not only a necessary accessory, but also a great gift

Once you get the hang of it, you can not only use such a product for yourself, but also give it as a gift. Therefore, it’s worth making several spare coasters: what if someone suddenly invites you to visit, and there will be nothing to give! And a stand for a mobile phone is always useful, even if a person already has one, then a second one will never hurt.

How often, when we are at home, in the office or on the road, we cannot remember where we put our phone. To prevent this from happening, you should get comfortable and ergonomic stands that you can make yourself. A phone stand can be made with your own hands from the most unexpected materials at hand. Ours will tell you how to do this. step by step wizard Class.

How to make a phone stand with your own hands: options for the office and car

Whether at work or in the car, we all need to be connected at all times. At the same time, you don’t want to spend a lot of money on expensive stands, because they can be made from waste and used materials.

Card stand.

The simplest version of a phone holder is a card stand. To make it, you need to carefully bend the unnecessary plastic card in two places, as shown in the photo below, without allowing it to break.

Experience shows that the stand is made of plastic card is very reliable and can even withstand air travel during severe turbulence.

Stand made from office clips.

To make a phone stand from paper clips or binders, as they are also called, you will need one large and one small clip. The legs of the small clamp should be placed between the holding part of the large clamp and the resulting structure should be placed on the table so that the clamp bigger size rested on its surface.

Similar coasters can be made in five minutes from clothespins.

Paper clips make great option car stands. To make it, you need to disassemble a large clamp and slightly bend the metal parts, as shown in the photo below.

To avoid damaging the surface of the phone metal fastenings It is recommended to wrap the threads in several layers. We return the holders to their place, additionally securing them with adhesive tape and a rubber band. We attach the clip to the ventilation blinds. The phone is securely attached between the metal parts of the binder.

Paper stand.

Regular office paper, folded in a certain way, can even withstand the weight of a large smartphone. To make a paper stand, you need to measure the dimensions of the phone and adjust the pattern below to fit them.

Cut the piece out of paper, fold it along the dotted lines and insert the side parts into the slots. This design is good because it allows you to charge your phone without removing it from the stand.

We study popular options for stands for home comfort

A desktop phone stand for the home should not only be comfortable, but also durable, stylish and fit well into the interior of your home. Let's consider options for such products.

Stand made of newspaper tubes.

A phone stand made from newspaper tubes will be a wonderful gift and an excellent decoration for any interior.

To weave such a stand, you will need several pre-painted long newspaper tubes, scissors, knitting needles, a little glue and varnish.

We place six blanks parallel to each other at a distance of approximately 1-1.5 cm and firmly fix them in the machine or in any convenient way. We place knitting needles or wire in the outer racks to make it more convenient to form smooth and neat contours of the product. We begin to braid the base with a working tube using the rope technique or calico weaving. We monitor the parallelism of the rows and, if necessary, coat them with glue for better fixation.

We weave a rectangular piece of the required length. We take out the knitting needles or wire. The ends of the stands are carefully tucked in and trimmed. We give the workpiece the required curved shape, if necessary, wetting it a little with water.

Similarly, we weave the leg of the stand using fewer tubes. We bend the finished leg, install it on the main part and secure its posts between the rows of the stand. We cut off the excess and hide it. We coat the product with glue, if desired, additionally paint it and cover it with 1-2 layers of varnish. After complete drying, the stand can be used for its intended purpose.

Stand made of origami modules.

Modular origami is a fairly young, but very popular type of needlework. With its help, you can make many unusual and original gizmos, including a phone stand from modules.

To make a stand you will need double-sided blue and Pink colour. We cut the sheets into blanks and fold the modules.

We start weaving from the base of the stand. It will require 28 blue modules, which must be connected to each other and closed in a ring. We make three more rows in the same way. From the fifth row we reduce the number of modules by 1, 2, 3, 4 pieces. In the seventh row we place one pink module in the middle.

In the eighth row we put 6 modules, make a skip, another 10 modules, skip, 6 modules. The number of pink modules is 2 pieces. In the next row, we place three pink modules on the pink section. We begin to design the shaped edging of the stand, as shown in the photo below.

In the back part we form a heart-shaped pattern, above which we install a number of modules blue color. Gradually narrow the stand until a triangular wedge forms at its back.

The module stand is ready!

Video on the topic of the article

We invite you to watch the video tutorials below on how to make other options for phone stands.

It happens that in some places there is not always a stable connection, in my case the Beeline operator, since the tower is located far away and nearby trees prevent it from transmitting the signal smoothly. I didn’t want to make any kind of antenna for the phone, I came up with a simpler one, this is a stand for the phone that could be placed in a place where the connection is stable and does not depend on weather conditions. And I’ll tell you how to make a phone stand in this article.

As with any other homemade product, we need to decide necessary materials.

To make this stand you will need:
* Parquet.
* Board 8cm wide.
* Epoxy adhesive.
* Threads, matches.
* Black felt.
* Hacksaw on metal.
* Drill and drill bits for it with a diameter of 3 and 6 mm.
* Coarse and fine grain sandpaper.
* Screw 55mm long.

These are all the materials we need, which are not difficult to obtain, and if there is no parquet, then any strong board will do.

Now you can begin the gradual production of the stand.

Step one.
The first step is to determine the dimensions of the future stand; to do this, measure the dimensions of the phone that you want to install in the stand in the future, and don’t forget to measure the thickness.

In my case, the thickness of the phone turned out to be quite large for the current time; after all, 1.5 cm is not small for a phone in 2017, but all this takes into account the fact that the phone has a protective bumper.
For convenience, we make a drawing on paper or in a program, as I did.

Step two.
After you have decided on the size of the stand, you can take up the tools and cut out the main part. The basis of the stand is its so-called back, the dimensions of which are 8*9cm. We take the thickness of the base to be 5 mm, no more and no less, since we don’t want the stand to be heavy or too fragile due to lack of thickness. To do this, I sawed an already cut 8*9 board across, reducing the thickness from 18 to 5 mm.

Now you need to drill a hole to attach the stand to the wall, first drill with a 3mm drill, then 6mm, but not all the way through, in order to hide the screw head. Then we round the corners with sandpaper.

Step three.
When the base is ready, you can start making the legs, which, due to their design, will prevent the phone from falling.
It seemed to me best to make the paws from the parquet that I found in my garage.

At first it was planned that the legs would be composite, that is, assembled from two parts.

But due to the loss of strength with such a connection, I decided to make them solid. The result is a foot in the shape of the letter G.

In my design there are three such legs.

Step four.
At the beginning of great importance appearance I didn’t add any pressure, but as production progressed I realized that all the sharp edges needed to be rounded, which is what I did.

It is best to round off sharp edges with coarse sandpaper. Once the desired result is achieved, sand with a finer grit to remove all burrs.
Also, do not forget to sand the main part, since the surface of contact with the phone should be smooth.
Step five.
After all the component parts have been sanded, you can proceed to attaching them to the base.
For these purposes, epoxy glue is best suited, which I have tested several times and has proven itself to be highly durable.

Using matches, mix the required amount of epoxy glue one to one and apply it to the places where the paws will be installed.

Epoxy glue takes a long time to dry, but keep it with your hands long time The parts to be glued simply do not have the patience. Without thinking twice, I decided that the easiest way to fasten such a structure was with thread and matches, wrapping a dozen turns around its edges. Because of large quantity turns of thread, everything is held securely, and most importantly, the parts are pressed tightly enough.
First we glue the bottom foot in the middle, and then the two side ones.

I had to tinker a little with the side ones, in this case it was better to ask a friend to help, since two hands were clearly not enough to hold two parts, and also to wrap it all around with thread.

Leave everything until completely dry.
Step six.
The epoxy glue has dried and despite the fact that the width of the contacting plane is only 5 mm, the paws hold on very tightly.