DIY cockerel made from plastic bottles. Step-by-step instructions with photos. DIY cockerel for the New Year Rooster made from plastic plates

I would like to introduce you to the cockerel Petrunya.
Not a single yard in a village or village can do without this magnificent bird. So I made myself a friend, a bright and majestic owner of the yard!

I will be happy to share with you the stages of its manufacture (based on the idea of making birds from plastic bottles Alena Zinovieva).

To make the mold we need:
1) 5l. canister (I use it from under liquid soap),
2) 5l plastic bottle,
3) metal-plastic pipe (leg height approximately 30-35 cm),
4) two 1.5 l. plastic bottles for thighs,
5) screws, scissors, stationery knife, screwdriver.

For fastenings, I use these self-tapping screws (I buy them by weight at hardware stores).
Small (about 1.5-1.6 cm) - for attaching feathers and component parts to each other.
Large ones (about 5-6 cm) - for attaching the head to the neck.

1) Move the top of the canister about 3cm.
2) We bend the metal-plastic pipe (shape the legs), in my case, the rooster walks ( right leg pushed forward), and fasten it to the canister with self-tapping screws.
3) For the neck, from 5l. bottles, fold the envelope, attach it to the canister with self-tapping screws.
4) From 1.5 liter bottles we cut out two “thighs”, which we attach to the canister with self-tapping screws.

For the feathers, I used bottles of this shape. We cut off the long neck, cut the bottle into 5 feathers (we are guided by the protrusions on the bottom of the bottle), and use the upper part of the feathers.

We begin to cover the body from the “thighs”. Disconnect them from the canister for convenience.
1) attach the corrugated tube to the neck of the bottle,
2) attach the feathers using wire.

We attach the finished legs back to the canister.

Starting from the back, we cover the entire body, except the back, with feathers (we attach it to the canister with self-tapping screws). We leave the back of the neck open because there will be other feathers there.

The next step is to start making the paws. From 2.5mm copper wire (or any other wire, preferably rigid, but not steel, which bends), we bend the shape of the legs (you can see more details in MK Filin). We create the effect of paws from a corrugated tube. We insert the remaining tail between the metal-plastic pipe and the corrugated tube. You can also fill the bottom with glue for strength.

We cut out claws from the bottom of the bottle (photo). They should be narrow and long. We fasten them with glue (I use “Moment of installation - liquid nails”).

We paint the body and legs using spray paint (I use universal enamel from KUDO).

We cut out the head from construction foam using a stationery knife, it is very sharp and the cuts are smooth and not torn. If the cutting process seems complicated to you, cut out all the parts separately! Then they can be glued together with glue.

Using sandpaper (medium), we bring it to the shape we need.

We treat the surface with acrylic putty, wait for it to dry completely and sand it again until smooth. After that, we treat it with ordinary PVA glue, so the paint adheres very well.

We begin to paint the head (you can use acrylic paints, it’s more convenient). Glue on the eyes (I bought them at a fabric store).

After fitting the head to the body, the husband said that the comb turned out not like a rooster’s, but more suitable for a chicken. I decided to redo it. I made a pattern out of paper (I tried it on for a long time to make it larger). I transferred it to foam plastic, cut it out and glued it in place of the previous one.

Using wire, we begin to attach the long wing feathers. The back remains open.

I cover the top of the wings with these feathers from 1.5 liter corrugated feathers. bottles The last row goes to the bend, into the inside of the wing.

We paint it with paint, let it dry well and attach it using perforated tape (sold in any hardware store) and self-tapping screws to the body. We bend the mesh for attaching the tail (you can increase its length and the tail will turn out richer).

Let's start making the tail.
We cut feathers from 2l or 2.5l. bottles into 5 parts. We paint separately on both sides (first we applied black, after drying a little blue)

We attach it to the mesh using wire. After coloring, I cut the feathers in half again, so the tail turned out to be more magnificent.

For the feathers on the back, I cut feathers of different lengths from transparent bottles (this makes it easier to color yellow), approximately 2-2.5 cm wide. I attached it to the back using self-tapping screws, 3-4 pieces at a time.

I will be happy to share with you the stages of its production (based on the idea of making birds from plastic bottles by Alena Zinovieva).

To make the mold we need:
1) 5l. canister (I use liquid soap),
2) 5l plastic bottle,
3) metal-plastic pipe (leg height approximately 30-35 cm),
4) two 1.5 l. plastic bottles for thighs,
5) screws, scissors, stationery knife, screwdriver.

1) Move the top of the canister about 3cm.
2) We bend the metal-plastic pipe (shape the legs), in my case, the rooster is walking (the right leg is pushed forward), and attach it to the canister with self-tapping screws.
3) For the neck, from 5l. bottles, fold the envelope, attach it to the canister with self-tapping screws.
4) From 1.5 liter bottles we cut out two “thighs”, which we attach to the canister with self-tapping screws.

We begin to cover the body from the “thighs”. Disconnect them from the canister for convenience.
1) attach the corrugated tube to the neck of the bottle,
2) attach the feathers using wire.

We attach the finished legs back to the canister.

We cut out claws from the bottom of the bottle (photo). They should be narrow and long. We fasten them with glue (I use “Moment of installation - liquid nails”).

We paint the body and legs using spray paint (I use universal enamel from KUDO).

Using sandpaper (medium), we bring it to the shape we need.

We treat the surface with acrylic putty, wait for it to dry completely and sand it again until smooth. After that, we treat it with ordinary PVA glue, so the paint adheres very well.

We begin to paint the head (you can use acrylic paints, it’s more convenient). Glue on the eyes (I bought them at a fabric store).

Using wire, we begin to attach the long wing feathers. The back remains open.

I cover the top of the wings with these feathers from 1.5 liter corrugated feathers. bottles The last row goes to the bend, into the inside of the wing.

We paint it with paint, let it dry well and attach it to the body using perforated tape (sold at any hardware store) and self-tapping screws. We bend the mesh for attaching the tail (you can increase its length and the tail will turn out richer).

Let's start making the tail.
We cut feathers from 2l or 2.5l. bottles into 5 parts. We paint separately on both sides (first we applied black, after drying a little blue)

We attach it to the mesh using wire. After coloring, I cut the feathers in half again, so the tail turned out to be more magnificent.

For the feathers on the back, I cut feathers of different lengths, from transparent bottles (this makes it easier to paint with yellow), about 2-2.5 cm wide. I attached it to the back using self-tapping screws, 3-4 pieces at a time.

If you want to decorate your yard, garden or country cottage area, but don’t want to spend money on expensive Consumables or buy ready-made factory products, then try making figurines from various available materials with your own hands.

Plastic bottles, corks, old car tires- all these are excellent raw materials for making beautiful things. A real decoration of your dacha will be a motley and bright rooster - the owner of the yard, who can simply “guard” the yard and serve as a weather vane.

There are many master classes showing in detail or giving instructions on how to make one interesting decor And what you need to do. Inspired by the ideas of the masters, you can easily make something out of unnecessary things and waste material very beautiful products.

Making a cockerel from plastic bottles

Plastic bottles and caps are practically the most affordable and cheap material for making crafts. In addition, its flexibility is a big plus - plastic is easy to cut with a regular knife or scissors, and if you need to round the edges or smooth the surface, this can be done using a regular iron.

The bottles themselves come in different colors, but a wider range of colors is very easy to obtain by using cans with various colors to your taste.

You can start by making simple shapes.

Take as a basis large bottle(usually five liters). You can paint it either with paints or with TEX enamel. Cut off the bottom and bend the edges inward.
The head can be made from papier-mâché or you can also use a bottle (you will need its lower part). In the second option, you will also need to make a beak for the rooster - this could be a bottle cap on which you attach the blank.
The legs are made either from a corrugated hose, or from old tubes, or from wire wound onto transparent tubes.
For the feathers and tail, you need to cut a lot of strips (you can cut each part into zigzag strips or separately). It is recommended to fasten it with glue and tape, self-tapping screws (there should be a lining made of foam plastic or wood inside the figure).
Cut a comb from the bottom of the bottle and attach it to the head of the cockerel. Wings can be made from halves of two bottles.
Paint the product using different colors and shades to make the bird colorful and bright. You can use quick-drying bronze varnish and colors to make it even more impressive.
Cut out the eyes from the same plastic and color or draw them. You can decorate them with eyelashes.

Such a rooster made from plastic bottles will look great on a fence, pole or fence of your dacha and even serve as an original weather vane.

You can simply build a frame for the future bird from bottles and cardboard, and then model a papier-mâché rooster figurine on it. Do not forget to dry each layer thoroughly, and then paint the product and cover it with yacht varnish.

Here is a more complex master class for making a cockerel, but as a result of all your efforts you will get a real sculptural masterpiece.

First you need to prepare a form - the basis for the future figure. The master proposes to build it from five-liter plastic canisters and bottles. This will be the neck and torso. For the bird’s legs you need to take metal-plastic pipes, about thirty centimeters high, plus two one and a half liter bottles for the thighs.
To attach the parts to each other, you will need large and small self-tapping screws.
Connect the base elements together: give metal-plastic pipes shape and position of the legs, move the top of the canister a few centimeters and roll an envelope from the bottle to form a neck. Also cut out the thighs and attach them to the canister.
You can cut five feathers from one large bottle. Just first you need to cut off its long neck. You will need the top part of the feathers.
Cover the figure with feathers starting from the cockerel's thighs (you can detach them to make it more convenient. And when you're done, attach the legs back). Then work from the back and attach the feathers with self-tapping screws everywhere except the back and back of the neck (you'll need different feathers there).
Weave the legs from rigid copper wire and supplement them with corrugated tubes (there should be a hole in the middle through which you need to insert a piece of wire to attach to the legs).
Cut the claws from the bottom of the bottle and attach them with glue or liquid nails.
Paint the finished part of the bird (KUDO paint or enamel).
Now it's time to work on the cockerel's head. To make it, it is recommended to use construction foam (the parts can be cut out separately and then glued together. Use a stationery knife for cutting). To give your head the required form, you will need medium sandpaper. Then the part will need to be treated with acrylic putty, and when it dries, sand it thoroughly. When you achieve the required smoothness, go over it with glue (ordinary PVA will do). Only after complete drying can you begin painting.
You can also paint your head with acrylic - it’s much easier and more convenient. Pick up cockerel eyes at a fabric store and glue them into the holes.
The shape for the wings is cut from the mesh using side cutters. Attach long feathers to it, leaving the back open. On top you can also add plumage cut from corrugated bottles. Paint the new elements and let them dry. Then attach it to the body using self-tapping screws and perforated tape.
For the tail you will need to cut a lot of feathers and paint them. Attach it to the protruding part of the mesh from the wings (if you bend it, the tail will be more magnificent and luxurious).
Now close the backrest. To do this, cut out many feathers of different lengths and attach them several in rows. It is better to attach the last row with glue so that the heads of the screws are not visible. For the back of the head and sides of the head, use finer feathers.
Paint the new plumage, after covering with construction tape and bags those parts of the cockerel that were already painted earlier.
Insert spurs into the bird's legs and cover it with glossy varnish.

If you want to decorate your site or house in an unusual way, there is no need to spend money on expensive sculptures or consumables. From various available materials you can make a figurine of a funny, bright cockerel.

Bottles and caps made of plastic are the most affordable material. Big advantage– pliability. Such plastic can be easily cut with a knife or scissors, and you can use a regular iron to round the surface and edges.

From plastic bottles

You can use multi-colored bottles to make crafts, or you can achieve a suitable color range using spray paints or TEX enamel.

Prepare in advance:

several empty plastic bottles;
wire or old corrugated hose;
Styrofoam;
scotch;
self-tapping screws;
glue;
paints.

How to make a rooster from plastic bottles? An empty five-liter bottle is used as the basis for the craft. Cut off the bottom from it, bend it inside the edges.

The cockerel looks great on the fence of the dacha or serves as an original weather vane.

There is another option for making a cockerel from plastic bottles: a master class designed for beginners. The craft does not require any special skills.

Prepare in advance:

three brown plastic bottles;
disposable cups and plates in yellow and red colors;
yellow ball for dry pool;
double-sided tape, regular tape;
stapler;
black marker.

Cut off the top parts of the bottles and fasten them together.

There is a more complicated option. It makes it possible to get a real sculpture on the site.

To work you will need:

They start by making the body and neck of the future sculpture. They are made from five-liter and one-and-a-half liter bottles. Pipes are used to make legs. For thighs, take a one and a half liter bottle.

Self-tapping screws of various sizes are used to fasten parts together.

The pipes are shaped and given the desired position of the bird's legs. Move the top of the bottle a few centimeters and roll up an envelope for the neck from the second bottle. The hips are cut out and attached to the base with self-tapping screws.

Feathers are cut from parts of bottles along the entire length. They cover the body of the bird, starting from the bottom. It is best to attach the feathers to a wire. The body is closed, leaving part of the neck open at the back. Another type of feathers is attached there.

Bend the wire for the paws. The hose will complete the further shape.. A tail is inserted between the pipes and everything is fixed with glue. Long and narrow claws are cut from the bottom of the bottle and secured with glue. Paint the sculpture using a can of spray paint.

While the body and legs are drying, they make the head. It is cut out of foam plastic using a stationery knife. The cuts must be sharp, but not torn. You can cut out the head in parts and then attach them with glue.

Irregularities are removed with sandpaper. Then the surface is treated with acrylic lubricant. Apply a layer of regular glue and wait for it to dry completely. After this the bird's head is painted acrylic paints, make eyes.

The head is attached to the body. Prepare the mold for the wings. They are attached to the back of the bird, leaving it open. Painted.

For the tail, feathers from a two-liter bottle are cut to length, painted on each side and attached to the body with wire. To complete the work, cut the feathers short, a couple of centimeters in length, and attach them to the back with self-tapping screws.

The option is difficult, takes a lot of time. But the end result is a real masterpiece.

Plywood figurine

You can make a cockerel from plywood. Even a schoolchild can do this kind of work.

Prepared for work:

Making a cockerel with your own hands– work for the diligent and patient. It requires attention, time and effort. But with desire and patience, everything will work out for beginners. The main thing is to follow the step-by-step algorithm.

To color the product, take bright colors. At the end of the work You can coat the cockerel with varnish. When using acrylic paints, varnishing is not necessary.

From bottle caps

To make a rooster from plastic bottle caps, prepare a diagram in advance. A suitable option for cross stitch or bead embroidery. The final work will be very impressive.

Collect the required number of caps in the desired colors. For accuracy, you can line the surface, as in the diagram. Glue corks if the panel is horizontal, or nail them if the work is vertical. Lids are easier to attach reverse side. They hold on tighter, and the cockerel turns out to be especially impressive from a distance.

If suddenly there are not enough caps of any colors, acrylic paints will solve the problem. In places where it is impossible to nail the cork, attach it with a gun or glue.

After completing the work, remove the auxiliary lines.

The application can be done on external wall or inside the apartment.

From old tires

Old car tires are an excellent starting material for creativity. The dacha will be decorated with a colorful cockerel. Prepare a pair of tires, two polyethylene tubes, and a piece of plywood for small parts.

The body of the bird is made from one whole splint, the second is used partially for the tail. The tubes are taken for the legs of the rooster.

To cut tires, use a hacksaw or an electric hacksaw. A sharp, large knife will also work. Wooden parts It's easier to cut with a jigsaw. But it is much more convenient to use plastic instead of plywood.

They secure everything with bolts and wire. Insert into legs metal fittings so that one end of the rod enters the ground, the other is attached to the hole in the tire. Then the sculpture is not afraid of bad weather.

A do-it-yourself wooden rooster is a task for a real master. Special knowledge and ability to work with the tool and feel the material will be required. It is very difficult for beginners to cope with such work. Even detailed master classes without certain skills they will not give you the opportunity to truly make beautiful product from wood the first time. A plastic bottle is an easy-to-work and simple material. TO creative work Even children can be involved.

Attention, TODAY only!

Making a rooster from plastic bottles with your own hands is easy; step-by-step instructions are proof of this. The first version of the craft is perfect for working with kids, and the resulting souvenir will look great at home or on the property. The second craft made from this material is a more complex craft that requires certain Additional materials and knowledge.

Now you can start making the paws, for which you will need copper wire. You need to bend the shape of the legs, and then create from a corrugated tube desired effect. Insert the tail between the two tubes and secure everything with glue for strength. Cut the claws from the bottom of the bottle, they must be long and narrow, and attach using glue. Using a can of spray paint, paint the existing parts of the cockerel.

While the body and legs are drying, you can start creating the head. First, it should be cut out of foam plastic using a stationery leg. The cuts should be sharp, but in no case torn. If it is difficult to cut out the head at once, you can cut out its parts separately and then fasten them with glue. Sandpaper will help remove unevenness, and then treat the surface with acrylic lubricant. Then apply a layer of regular glue and, when it is completely dry, paint the bird’s head with acrylic paints and make eyes.

Now fit the head to the body. Prepare a mold for the wings and attach the long wings to the back, leaving it open. Color everything, make a tail. To do this, cut long feathers from a two-liter bottle, paint them on both sides and attach them to the body, again using wire. To finish the feathers on the back, cut out short 2 cm feathers from bottles and attach them to the back; you will need self-tapping screws for this.

Step-by-step instructions first or second will help you make a rooster out of plastic bottles with your own hands. The first version of the craft is easy, requires a minimum of raw materials, and such a cockerel can be made even by children. The second bird turns out to be large, serious and delightfully appearance. If you want to build it, it should also work out without any special problems. A simple and quick craft -