Hammock - making at home: options, drawings, weaving. Weaving a hammock with your own hands: a diagram of the product, how to use it, the history of the origin of this item and instructions for its implementation using the macrame technique How to make a hammock from

Any person who has own house or country cottage area, dreams of at least occasionally lying in a hammock, hiding from the hot rays of the sun. However, many people tend to think that it is almost impossible or very difficult to weave a hammock with your own hands. But this is absolutely not true. everyone can do it. It just takes a little patience.

Therefore, let's consider different ways how to weave a hammock.

Today there are many types of different hammocks. Accordingly, the materials used for them are also different. The most popular is Brazilian. It is distinguished by its relative simplicity of weaving and high strength and durability.

Weaving a Brazilian Hammock

Before you start weaving a hammock with your own hands, purchase necessary materials. There are only two of them: a very thick cord that can withstand up to 200 kg (about 25 meters will be needed), and a large piece of strong fabric, the average size of which is about 230x120 cm. To weave this type of hammock, you won’t need anything else except yours skillful hands.

So, we start by taking a piece of fabric and carefully hemming it on all four sides. This is necessary so that the edges do not fray. Next we make rope blanks. To do this, cut about 12 pieces from the rope. Moreover, the length of each is 15 cm. This will be a kind of basis for the initial loops.

On each side of the hammock you need to put 6 such ropes, first folding each one in half, with a grip of 2-2.5 cm, and stitching. You will end up with something similar to a fringe about 3 cm long. Remember to maintain a distance of 10 cm between the ropes when applying and stitching.

And in order to have more confidence in the reliability of the hammock, it is advisable to additionally stitch the edge of the fabric with loops with a thick ribbon. Now through the resulting loops we pass a cord 75 cm long, the ends of which are then tied. It turns out that all the loops are connected with a cord at the edge into one whole.

You also need to do this on the other side of the hammock. After this, we take the remaining part of the cord, make a couple more knots and twist the two tails into one according to the pigtail principle. At the end we tie it all off several more times, leaving about 25 cm free. We tie the rope to a thick tree branch with these ends. We do the same on the other side and also tie the other end of the canvas to the tree. This way you will have a hammock in which you can lie, swing and enjoy the fresh air.

Return to contents

Hammock with full wicker base

The next type of hammock is more complex, since its entire base is completely woven from cord. To work, you will need as many meters as possible (minimum 150) of very strong cord, scissors and two wooden planks, each 80 cm long.

First we work with the planks. In each piece of wood, you need to make 6 holes at a distance of approximately 5.5-6 cm from each other. The thickness of the holes should be such that the double cord can pass through them normally. After this, cut the cord into 12 equal pieces. The length of each such segment is at least 3 times the expected length of your future hammock.

Now we take two pieces and insert them into the hole on wooden block. We do this with all cords. Now we take the outer ends, the length of which should be at least 1.5 meters, tie them all together, twist them and make a loop, for which the hammock will then be attached to one side.

All other ends of the cord, which are located in the inner part, need to be tied together in twos in the form of knots, as shown in the diagram. In this case, it is important that in the finished knot one lace comes from one hole, and the second from the next nearby one.

Stages of making a hammock: 1 - Assembling the hammock, 2 - Tying the cords, 3 - Securing the rope.

This will give us the first finished row of the hammock. All subsequent rows are made using the same principle. It is very important not to forget to tie only those ends of the ropes that come out of adjacent holes, and not from one. Also try to ensure that the resulting cells are the same and not too large. After all, a hammock with smaller mesh cells will withstand significantly greater loads.

After you have weaved the length of hammock you need, you need to insert two ends of the remaining ropes from different holes into one on the second prepared wooden plank. After this, the ends need to be tied, and the outer ends should be connected together and also tied into several knots. After this, twist them and make a loop through which the hammock will be hung on the other side. Now you can safely use this hammock for relaxation.

Looking for tips on how to make your own hammock has brought you to the right place. Here they will tell you how to make a hanging bed for relaxing and sleeping, and will also provide you with drawings and recommendations. The fact is that hammocks can be very simple, the production of which does not require large expenses manual labor. The main thing is to carefully select materials and carefully follow the instructions. For those who want to get something special at home or in the country, a master class of more complex products is offered.

Sling style hammock

A Mexican hanging bed is easy to make at home. You will only need to select two thick pieces of fabric from available materials (the width of each piece is 1.5 m, the length is 3.2 m), which should be tucked and stitched along the edges.

Note! To get out of a Mexican hammock, you need to take a separate master class (just kidding!). However, it is truly impossible to fall out of it, and getting back up will require some effort. Therefore, it is inconvenient for older people. But its lightness and compactness make this model indispensable on a hike.

The offered hammock has design feature, thanks to which it can be used in 2 versions: enveloping (original) and spacious. The modification is achieved by inserting dense fabric (mat) into the bed through the holes marked in yellow in the figure. Study the drawing and get down to business:

1. 2 meters of fabric on both sides, marked in green, should be sewn.
2. 1.5 meters each, marked in red, must be stitched, turning them in by 2-3 cm.
3. Pull the cord into the holes along the edges.
4. Cross the cord and tighten the ends, gathering the fabric into a knot.
5. Wrap the ends of the cord twice around the tightening area and tie them with a “noose” knot.
6. Wrap the ropes intended for hanging around the tree.
7. Then attach the ropes to the knots that secure the edges of the hammock.

The structure will hold more firmly, and the wood will not be damaged, if fabric is first placed under the ropes. Alternatively, hanging ropes can be threaded into tubes. Check the strength, adjust the tension and enjoy your relaxation, the master class on making a simple hammock is over!

Wicker hammock

It is, of course, easier to make a hanging bed from a whole canvas. However, a hammock mounted on cross poles is more spacious and comfortable. And despite the laboriousness of the process, many people like this design. There are several options for hammock knots, each of them has its own advantages and disadvantages. Before you make a hammock with your own hands, you will have to master the skills of weaving macrame.

• Threads thrown over (without knots, the threads are simply thrown over, like in factory hammocks). Advantages: the net is woven very quickly, this weaving method is the least material-intensive, the resulting fabric is quite flat (the knots are not pressed into the body when lying down, even without lining the fabric). Disadvantages: the cells are unstable and easily change size. Over time, holes will appear in the hammock, which will not add comfort.

• Square knots (double flat knot). Advantages: very dense plexus, cells are clearly fixed, knots are flat, cell size is easy to adjust. Disadvantages: the most material-intensive method and, therefore, the resulting hammock will be the heaviest. Taking such a hammock with you on the road is expensive.

• Flat knots (degenerate square knot, without two strands inside the knot). Advantages: the net is woven quickly, it is easy to adjust the size of the mesh, the rope consumption is low. Disadvantage: there is a possibility of the knot turning out if there is excessive load on the thread.

Flat knot weaving pattern

• Triangular knots (bowlines), such knots are used to knit nets for the most different needs. Advantage: the cells are fixed rigidly. As a positive point, one can also note the average consumption of the rope and, therefore, average weight. Disadvantages: the work of weaving such a network is the most labor-intensive, the knots on one side are sharp, and the mesh sizes are difficult to adjust.

Triangular knot: one side view

Triangular knot: view from the opposite side

One of the possible weaving patterns for a triangular knot

Dilemma: with or without a corner?

Before you make a hammock with your own hands, you need to decide whether to bring all the threads into a ring, as in factory-made products, or not. The corner (this is the name of this design solution) looks quite attractive, but it is not so easy to connect it at home.

To bring all the threads into a ring just as effectively, you will have to try. In addition, it should be taken into account that the resulting angle will be very tight, almost not subject to deformation. As a result, the compactness of this hammock model will decrease, and taking it on a hike will not be so convenient.

Weaving a hammock at home, and even for the first time, when any action is an experiment, leaves its individual imprint on the accuracy of measurements. Therefore, we can recommend taking materials with some reserve, because it is easier to trim than to sharpen. In order to build a corner, you will need 20 free ends (10 threads, 10 passes), which will eventually be attached to the mesh. All threads are the same length; after pulling them out from the corner, you will get an even line consisting of free ends. These ends are then passed through the crossbar and attached to the mesh. You can take 10 threads of 300 cm each, folded in half they will look like 20 threads of 150 cm each. The result will be about 40 cm from the top point of the triangle to the crossbar.

Subtleties of weaving

Most often, a hammock intended for a summer residence and country house, a bowline knot is woven. The reason is the rigid fixation, which is in demand not only in hanging places for rest, but also in a wide variety of things: sports nets, bags and pouches, fishing nets, stitching and lace. The thickness of the nylon rope must be at least 6 mm. You should choose a dense winding with nylon filling.

Sometimes in discussions you can hear that this or that master used a thread about 4 mm thick. If you are sure that you will not allow children near the hammock to test its strength, you can try it. Otherwise, a suspended bed on which a large man can sleep peacefully may not be able to withstand one or two pranksters. You shouldn’t get carried away with excessive strength either: a hammock made from a 10 cm thick rope will resemble a volleyball net. This, of course, will increase reliability, but such a “bed” will look terrible.

The consumption of the rope depends on the method by which the knitting is performed, the desired size of the bed and the size of the cells. The larger they are, the less material will be needed, but keep in mind the fact that any mesh will become slightly deformed over time. When weaving cells with a diameter of 65 mm with a triangular knot, 40 5-meter threads will be required, the total material consumption is 200 m. With such calculations, the planned fabric should be 180x70 cm in size from diamond-shaped cells 40x80 mm.

A master class covering hammock knitting would be incomplete without mentioning the need to strengthen the longitudinal edges of the fabric. They should be reinforced with strapping that can withstand the maximum load created during lifting or laying. You will need to make a very tight knit from the same material that was used for the main stock, or you should look for a thicker rope for a similar purpose. Approximately, to weave 1 m of rope you will need 5.55 m of thread.

If the hammock will be used primarily permanently, in the country or at home, a model with an angle will look preferable. The reason for this choice has already been discussed above. The number of ropes in the mesh should be selected as a multiple of 4 - the reason is that 2 threads at the edge of the mesh will be attached to 1 thread of the corner. That, in turn, is formed from an even number of ropes. In addition, it must be remembered that longitudinal ropes also require fastening. There are 2 possible solutions to this issue, which the schematic drawing will introduce you to.

In the picture on the left, the side ropes are attached separately to the crossbar, the entire network is woven from a number of threads that are a multiple of 4 (for example, 40). The schematic drawing on the right suggests making a mesh of 38 threads, and combining the side ropes when tying at an angle with the outer threads.

Let's hurry without haste

Whoever hurries will make the neighbors (or at least the neighbor's children) laugh! No matter how good the master class is, no matter how with skillful hands No matter what you have, you still shouldn’t start sewing a hammock right away. Be sure to make a test weave of at least 8 threads. It will help reveal the shortcomings of a particular method and reveal several previously unaccounted for details.

Look for a simple rope at your dacha or at home, 8 pieces of 2 meters each will be enough, something made of wood (for the crossbar) and try it different variants nodes and cell sizes. When you decide what you want to sew and which drawing you are using as a basis, weave a mesh along the entire length of the threads. Measure the dimensions of the resulting model and estimate how many materials will be needed for the entire structure.

When you have acquired the required rope, perform a second test approach. Take 2 pieces of 10 meters each, tie them around a round block of wood (you will get 4 ends of 5 m each). Weave the mesh, measure the remaining threads (don’t forget to leave 25 cm at the ends to secure the fabric), make adjustments to your calculations, because this is inevitable; at home, accuracy can only be achieved experimentally.

The choice of fabric or the decision to make a children's hammock for your child makes adjustments to the calculations. However, now, after several approaches, you know exactly how to weave a hammock. And after making your first model, you will be ready to conduct a master class!

This article - detailed story about how to do wicker hammock with your own hands. What to pay attention to, what are the options for knots and weaving. How to decide on the size, where the rake is and how to avoid stepping on it. Is it worth taking on this activity at all? This is a story about gaining personal experience.

Preamble

Surely everyone knows from childhood what a hammock is. Perhaps someone was even lucky enough to lie in it. If you don’t know what we’re talking about, go to Wikipedia.

There is a wonderful company, "Expedition", which produces all kinds of tourist swag and jokes on the topic. So I came across their “gags” in the store, and among other things I saw a fully functional hammock. Only not wicker, but from a whole cloth. Cost about 800r. All this is cool, of course, but there are no crossbars in it, which means you have to lie like in a sack - it’s not a fountain. So you have to do it yourself. I was planning on taking it camping on the weekends. The fuse was received, and away we go...

Search

I searched Google on the topic and found a lot, but it was all wrong. I found a couple of sources copied from the same article from the magazine "Young Technician" No. 6, 1983! Yes, the glorious 83rd, “a wonderful time of childhood, wooden Toys, nailed to the floor.." An attack of nostalgia gave way to disappointment: the pictures are of poor quality, the names of the knots are the same as in Chinese. By the way, there is an article floating around on the RuNet on how to make a rag hammock. Pattern, explanations, everything is written down to the smallest detail. But to the topic This story does not apply.

Switched to search in English. As a result, dozens of American websites offer to buy (!) the same models of hammocks. A large selection of prices, colors, materials and all that.. but not our choice :) And not a single decent site with a story like “hand made”. Here it is - capitalism face to face :) - any whim for your money.

In general, I collect from the world one by one. I found a site dedicated to macrame. Not even a website, but rather a home page. Nevertheless, it was there that the truth was revealed! Diagrams of almost all necessary components, definitions of concepts. Thanks to the author, "respect and respect"! :)

Choosing a method

I decided on the terms and began experimenting. I found four ways to weave the main fabric (mesh):

Another interesting point. On factory hammocks, all the threads are brought together into a ring, and this reduction looks very beautiful. It's called an angle.

How I worked hard to get the same angle! So many approaches and searches... I almost gave up on this idea, but I was still able to weave the desired pattern. I saw it in the "How it's done" series. Attention: this angle is very tight and practically does not deform. That. in a twisted hammock it will stand out a lot, that is, stick out :) (this again applies to using a hammock in camping conditions).

Weaving patterns for "square knot", "bowline" and "corner" in this archive.

I did not weave the whole fabric in all ways, because... It's costly in terms of time and money. I tried to weave on eight test threads, two meters each, and figured out what it would most likely look like.

Eventually "behind" And "against":

1. 
   + it weaves very quickly, a minimum of rope is needed, the fabric is almost flat.
   - the cells will be floating, i.e. will easily change the size, which means there will be “holes” in the stock. There will probably be discomfort.
2. square knots
   + the most dense plexus, relatively fixed cells, flat knots, easy to adjust cell size. Theoretically, there should be no discomfort at all.
   - you need twice as much rope as in other methods, the weight will also be twice as much. But weight is already a critical factor if you take a hammock with you, for example, in a PVD.
3. flat knots
   + weaves quickly, the mesh size is easily corrected, minimum consumption ropes.
   - we load one thread - the knot turns out (see on photos bottom left). Perhaps nothing will happen in the composition of the canvas, but I didn’t like this behavior.
4. triangular knots
   + rigidly fixed cells, average rope consumption, therefore average weight.
   - it drags for a very long time, on one side the knots are sharp. Each cell has to be measured, it is difficult to correct the size. After four hours of work, my fingers hurt. I have to quit.

Well, here we go.. :)

Before we talk further, we need to clarify the following: all the figures given are my measurements, yours may be different. My work plan and calculations changed several times. Instead of 38 threads, I ended up weaving a mesh of 40. At first, the purchased rope turned out to be a lot - when I first made the canvas, then there was barely enough - when I made the corners and side ropes. Therefore, approach the matter creatively; it is unlikely that you will be able to calculate everything accurately.

After all the tests and measurements, I finally decided to weave the main fabric using triangular knots. In a tourist store I found a nylon rope with a diameter of 6 mm. Not some dubious Chinese city..., but a putin line "Needle line": tight winding, nylon filling, 5 rubles/m. Tension per meter of rope: I was able to stretch it by 5 cm, let go - the rope returned by 2 cm. It seemed quite strong. In the same store I saw a ready-made hammock made by Chinese makers, woven using the first method from ordinary rope ~10 mm thick. In its appearance, it resembled a school volleyball net - a scary look, although reliable.

Note: I read somewhere on the forum that the thickness of the rope should be at least 4 mm. I think it's very subtle.

We’ve decided on the thickness, but how much to take? During the test weaving I came to the following (only for weaving with triangular knots): I make 65 mm cells, from 40 threads of 5 meters each, the resulting consumption is 200 m of rope. I assume that the canvas will stretch out and the cells will be diamond-shaped. I plan to get a 180x70cm canvas from diamond-shaped cells, the diagonals of the diamond are 40 and 80 mm. If you make more cells, you will need less rope, but I cannot say what the cell/thread length ratio will be.

Side ropes. The edges of the hammock need to be tied, and this harness will receive the maximum load - body weight when the user gets up / lies down in the hammock. Therefore, you need either a very tight knit or a thick rope. Again I found the answer - “How it’s done.” Calculation: 5.55 m of rope - 1 m of rope.

If you plan to make a hammock with corners, then the number of mesh threads should be a multiple of 4. Why? Every two threads at the ends of the mesh will be connected to one corner thread. The corner, in turn, is also assembled from an even number of threads. Hence the divider 4. On the other hand, you need to take into account the presence of side ropes (they also need to be secured). Options: you can weave a mesh from a number of threads that are a multiple of four (for example, 40), tie them at an angle, and secure the side ropes separately to the crossbars. Or: a net of 38 threads along with two side ropes will be in an angular harness.

I can’t explain this idea with photographs, because I’ve written so much on my hammock that I’ll have to shoot a 3D video :-/ I can only give a schematic drawing:

Rake

Problem #1. When I measured the test weave, I used 8 strands. So I didn’t take into account that intertwined 36-40 threads will give a completely different width, rather than calculated (measurement errors). In general, my width turned out to be 85 cm instead of the calculated 70 cm (!).

What needed to be done? Weave one row of all threads and try it on. I measured it somewhere in the middle of the canvas, it’s too late to rush around. A few more words about the sizes: I made the final length of the fabric (mesh) 200 cm. After practical testing, I decided that 180 cm was enough, but I didn’t want to unravel the excess.

Problem #2. As a result, the whole structure turned out to be large - the length of the crossbars is 120 cm, the diameter is 20 cm in a twisted state. In addition, the weight is about 4 kg. Not suitable for hiking. We'll have to give up something, like a guitar and beer... I'm not ready for such sacrifices yet, so now we take a hammock with us only if we go out by transport.

Comment. When weaving bowlines (triangular knots), you need to take into account that when forming a knot one thread is consumed more. It forms a loop for the knot. Therefore, you need to alternate the forming thread, change it when weaving a new row. This is difficult to explain: when we weave a row, we need to stick to one knot formation pattern. For example, take the left thread for a loop. Then in the next row for the loop we take the right thread. Everything is clearly visible from the pattern when you are already weaving.

Forest tests.

Despite problem No. 2, a hammock in the forest on vacation is such a HIGH! At least get in line so you can lie in it :) By the way, about “lounging”: I lay down for about 30 minutes, without a T-shirt.. Almost no discomfort. As a result, I got these marks:

Sharp knots are the main disadvantage of the bowline weaving method. But the cells do not scatter and the hammock keeps its shape. If you at least put on a windbreaker or go to bed with clothes on, then in general everything is fine. The height of the hammock attachment is approximately 2 m from the ground. Yes, yes.. I was surprised too until I checked it. You need to pull the fabric tightly; after the first laying down, the hammock sags and stays about half a meter from the ground. Our beta tester took the risk of spending the night in it. He came to the tent in the middle of the night and said that he was cold. Indeed, the grid does not heat, it does not heat at all: D

Additions to the article

Addition 1: side rope

how to weave a side rope

how to weave rope into a net

You need to consider the following:

• if you weave a rope into a mesh, then you must check the dimensions of the cells after tying, so that later it does not happen that the rope collects/stretches the fabric;
• You don't have to weave the rope into the mesh like I did on my hammock. You can make it separately and then pass it through the outer cells;
• It is advisable to tighten each knot, otherwise the rope will stretch unpredictably under load. I didn't drag anything out in the video, it's a demonstration;
• You can not weave side ropes at all, but simply take a thicker rope. The main thing is that she required length withstood the weight of a person.

Addition 2: stand

You don't have to hang a hammock on trees. Maybe your country villa doesn’t have trees in the backyard;) Below are several options for hammock stands - let’s take an example from the Americans. I will not describe the dimensions and technology, because... If you have two straight arms, it is not difficult to make a similar design.

Addition 3: weaving, rag hammock

According to search engines, people land on this article when they are looking for related information about weaving. there is an article on how to do it basketball net, billiards bag, volleyball net and so on. If for some reason the link is dead, you can download the topic in pdf format.

Again I found on the Internet a pattern for a rag hammock, which I talked about in the article - download (pdf format). This is one of many options. Unfortunately I don't know who the author is.

The hammock is an invention of the South American Indians. It is quite simple to do, and is used not only as furniture for comfortable sleep, but also as protection from dampness and midges.

Materials for production

The most important thing to consider when making a hammock chair with your own hands is the choice of material. The most durable fabrics:

• canvas;
• calico;
• mattress teak;
• camouflage or canvas fabric.

Synthetic products are also suitable for use, but they have one significant disadvantage - they do not “breathe”.

If we talk about cords, it is better to choose threads made of cotton. Synthetics in this case again loses. Cotton cords are more pleasant to the touch. They are easy to tie into knots and intertwine with each other.

General rules

Regardless of what kind of hammock chair you decide to make with your own hands, there are some rules that for all types garden furniture of this type remain the same.

• The product is suspended either between two supports or between two trees. If you choose the latter option, the diameter of the tree trunk must be more than 20 centimeters. The supports are sunk into the ground to a depth of one meter.
• The ropes are strong and thick. They should reach 8 millimeters in diameter. In some cases, the fabric is strengthened using eyelets.
• Install the hammock at a height of one and a half meters above ground level. Between support pillars the distance should reach 3 meters.

DIY hammock (video)

How to make a Mexican cocoon hammock

If you are thinking about how to make a hammock with your own hands, the presented option is one of the simplest. At the same time, it is quite convenient to use.

When folded, the hammock weighs 1 kilogram, making it convenient to carry. It is almost impossible to fall out of the “cocoon,” but you will have to work hard to get out of the product.

To make this type of hammock you will need:

• a cord 20 meters long (it can withstand weight up to 200 kilograms);
• thick fabric– 2 pieces of 3 meters each.

The assembly proceeds as follows:

• the cuts are folded together;
• they are stitched towards each other on both sides, it should look like a tunnel with unfinished edges;
• the narrow side of the hammock is turned up a couple of centimeters and stitched;
• the resulting tunnel is pulled through the cord;
• then the cord is crossed and tightened so that the fabric gathers slightly;
• The place of tightening is wrapped several times with a cord and a knot is tied.

Important! To avoid damaging the tree bark, there should be a cloth at the point of contact between it and the cord. What should a hammock look like? finished form, you can see in the photo.

Wicker hammock

Previously, hammocks resembled a regular volleyball net. Now there are many improved options. It is enough to learn the macrame technique and you can make a beautiful and comfortable product yourself.

You will need:

• 2 slats - the length should be one and a half meters;
• rope with a diameter of 8 millimeters.

The rope is attached to the bars through specially made holes, whose diameter should be 20 millimeters. The distance between them should reach 5 centimeters. In order for the rope to fit firmly into the holes, the diameter of the latter must be made according to the 1/3 principle.

How much cord you need depends on the pattern you choose. How to calculate the amount of rope required? Measure the distance between the slats, multiply by 3. Then the result obtained should be multiplied by the number of holes.

Important! During use, a hammock made using the macrame technique does not lose its shape.

The technology is simple. To create a knot, 4 ropes are required. The cells should be less than 7 centimeters. Metal rings provide additional structural strength.

How to secure a hammock (video)

When installing a hammock on supports, the length of the product is adjusted by tension. You can tie it higher and make the bend stronger.

Brazilian hammock

How to make a Brazilian hammock with your own hands? You will need:

• nylon linen cord (2 packs of 10 meters each);
• 2 pieces of fabric measuring 90x200 centimeters;
  drill;
• 2 wooden sticks 90 centimeters long.

Assembly of the product consists of several stages.

• Two pieces of fabric are sewn together.

• Then markings are made for the eyelets; the distance between them should reach 8.5 cm. You can insert the eyelets. If there are none, loops are sewn on. The cord passes through them, as well as through the eyelets. If possible, it is better to use hardware, they are more reliable.
• The sticks must be marked. A distance of 2.5 centimeters is departed from the edges. Then measure 8.5 cm from the marks.

• For an 8mm cord folded in half, you need to drill holes with a diameter of 20mm.
• The cord is cut into meter-long pieces. Each piece is threaded through a hole in the stick. It must be inserted through the grommet, then again through the stick.
• At a distance equal to half a meter from the end of the stick, all the cords are collected together. All that remains is to tie a knot and tighten it.

• Next, the knot is braided. The hammock is ready to use! You can see what it looks like in the photo.
• You may also be interested in an article in which we talk about what can be made for a summer house from plastic bottle caps.

Anyone can make a hammock on their own. It is important to choose the right materials. The cord must be durable, the fabric must be reliable, breathable, and made from natural materials.

There are several types of hammocks, which one to choose is up to you. If you want to receive comfortable place for sleeping, it is worth choosing a “cocoon”; if the main thing is aesthetics, you can weave the product using the “macrame” technique. Whichever option you choose, you should stick with it. general rules for product installation.

Since prices in stores are only rising every year, more and more connoisseurs comfortable rest thinking about how to sew a hammock with your own hands. Made from fabric or woven using the macrame technique, it will help you relax and unwind in the fresh air with maximum comfort. And also save a lot of money and improve useful skills in the household.

How to weave a hammock with your own hands at home

1. Durable, pleasant to the touch rope.
2. Two metal rings.
3. Wooden or metal strips about a meter wide.
4. Tools.

Before weaving a rope hammock with our own hands, let’s do some simple calculations.

• The width of the slats depends on your preferences. Mostly it is made about 1-1.2 m.
• The total length of the rope is calculated as follows. Determine the distance from one plank to another. Add about a meter (for slings) to the resulting value. We multiply by 6 (since the “threads” during weaving will be double). We estimate how many holes there will be in the plank and multiply the length calculated in the previous step by this number.

When the calculations are finished, we proceed directly to weaving a hammock from a rope.

Step #1. We take the planks and make holes in them at a distance of 5-6 cm from each other. To prevent the weaving rope from tearing or fraying in the future, we process the holes to make them smoother.

Step #2. We cut the rope according to the number of holes in the plank. We take one of the metal rings and fasten the doubled sections on it with a loop and a knot.

Step #3. We insert the ropes into the holes of one of the planks. We check that the distance between the ring and the bar is 50cm (half the length we put on the slings). On the side opposite to the ring we tie the ropes in pairs.

Step #4. Let's proceed directly to weaving a hammock. If you are proficient in the macrame technique, choose any options for knots and weaves. For beginners, we advise you to stick to the checkerboard pattern.

Step #5. When you are finished with the “hammock body” (make sure that the last row of cells duplicates the first), we thread the ends of the ropes into the second bar and fix them with knots on the side outside the main mesh.

Step #6. We tie the remaining ends of the ropes on the second metal ring.

Step #7. To give the hammock the shape of a regular rectangle, we thread a rope through the side holes of the slats. In the middle we intertwine the ropes with mesh cells, and also attach the ends to the rings.

The hammock is ready, have a nice rest.

Weaving a round hammock: step-by-step diagram

Not all lovers of relaxation in nature are suitable for the longitudinal shape of a hammock. Some people don’t have enough space for large structures, while others prefer to sit rather than lie down while relaxing. A round product that can be easily hung in an open space or indoors is ideal for such people.

So, to weave a hammock with your own hands at home, you will need:

1. One or two metal hoops of different diameters.
2. Clothesline, nylon cord or other similar material for the hammock itself and for the slings.
3. Cord for wrapping the hoop.
4. Threads, glue and other auxiliary materials.

Step-by-step diagram:

Step #1. Calculate the length of the cord

The length of the rope depends on a number of factors: the diameter of the hoop, the size of the mesh and the desired tension force. To calculate it we do the following:

If you want to change the diameter of the cells, reduce or increase the number of segments.

Step #2. Wrap one or both hoops with cords

Try to avoid gaps and sagging. We secure the ends with glue, knots, fabric or any other option that seems reliable to you.

Step #3. We weave the seat.

Based on the diagram drawn earlier, we tie several ropes to the hoop and begin to intertwine. Please note that the “green” ropes are folded in four, the red ones - in half. For clarity in the photo green The “path” of one “quadruple” rope is highlighted, and the “path” of one double rope is highlighted in red.

Step 3.1. Making the back

If you want to make a hammock chair from 2 hoops, take a strong rope and fasten the hoops together on one side. We begin to braid the back. It can be the same pattern, or it can be different. Only the ends are now attached to the lower hoop. To add rigidity to the back, fasten 2 straight strips between the hoops and wrap them with cord.

Step #4. We fasten the slings

The hammock is ready. To hang it, we tie it to the (top) hoop of the sling. Then we assemble the slings into one knot or two (in the manner of a swing) and hang them. The round wicker hammock is ready.

Note! The simplest weaving option is taken as an example. If you are proficient in the macrame technique, you can use any other solution.

How to sew a hammock for a summer house with your own hands

Those who find weaving a hammock with their own hands to be something prohibitively difficult can opt for the fabric version. To make it you will need:

• Canvas at least 1 m wide.
• Rope or clothesline (at least 8 mm in diameter).
• Sewing and other accessories (for selected options).

When the necessary materials have been collected, we proceed directly to making the hammock.

Option #1. Hiking (for lazy people)

This method is considered the simplest, since it allows you to make a hammock yourself step by step in just 10 minutes.

Step 1. Calculate the length of the canvas. To do this, we determine where the hammock will hang and measure the distance between the bases (trees, poles). We add another 50 cm to the resulting value and get the length of the desired cut.

Step 2. We gather one edge of the canvas into an accordion, insert it into a carabiner and wrap it with rope so that the structure does not unravel. Repeat for the second edge.

Step 3. We tie ropes to the trees and attach carabiners to them. Ready.

Option #2. Dachny

This type of hammock for a summer residence is suitable for people who are willing to sacrifice personal time for the sake of comfort. Step #1. As in the previous case, we calculate the length of the canvas and cut it out.

Step #2. We prepare the “body” of the hammock. We make a hem on each side and sew it on sewing machine. On the long side there is a hem of about 10 cm and one seam. On the short one there is a hem of about 25 cm and 5 seams with high-strength threads. The distance between the seams is 2.5 – 3 cm.

Step #3. We fasten the rope. We thread ropes into the resulting holes and tie their ends to the tree. The hammock is ready.

Step No. 3.1. If you want to add strength to the structure, the last point can be done differently. When you have completed a large hem and stitched it, we insert strips into the resulting loops and tie the ropes to them.

Step No. 3.2. To make the hammock as comfortable as possible, we do the following. We cut small pieces of fabric and attach them to the canvas in the manner of loops. We string the loops onto the bar. We insert a rope into the side (lengthwise) folds and also tie them to the bar. We attach the hammock to the tree with another (or several) rope. Ready.

Step No. 3.3. If you are afraid of getting tangled with the slings, wrap them under the ring into a single bundle.

Making a hammock using the same pattern, different people get different results. The point here is not only in the directness of the hands, the quality of the materials, but also in small tricks that not everyone is familiar with. For example:

What tricks do you use? Do you know something useful and unusual? Share your experience in the comments, let's discuss.

How to weave a hammock in different forms: photos and videos

In the matter of weaving a hammock with your own hands step by step diagram useful for both beginners and experienced professionals. Therefore, we invite you to look at our collections of photos and videos demonstrating various models and their assembly options.

More interesting things on our website: