To the question Laying tiles on plaster wall from tongue-and-groove blocks... specified by the author Staff the best answer is If we were talking about a kitchen, we could get by with rotband plaster (the tiles stick to it normally).
But the linear expansion of materials in the kitchen and humidity are insignificant.
In the bathroom it's a different matter. And when building up a wall, dissimilar materials will crack along the joint, making gouging out the grooves a hassle.
You want your tiles to last at least 20 years?
In general, screw the plaster mesh over the wall, stick waterproofing on the floor mesh at the bottom of the wall (a strip so that 10 cm extends over the floor and the wall) - at least a piece of roofing material.
Plaster over the mesh with a composition for wet rooms on a CEMENT basis (after all, in tile adhesive, the cement component and adhesion will be better) and sculpt the tiles to your health.
Plaster on a grid will hide the joint of the wall being built up and strengthen the wall itself.
This will of course be considered a perversion!! But this is a very reliable perversion))
Winds
(163432)
you're welcome.
twist the grid as close as possible.
Answer from 22 answers[guru]
Hello! Here is a selection of topics with answers to your question: Laying tiles on a plaster wall from tongue-and-groove blocks...
Answer from Eurovision[guru]
Of course it is possible.
Answer from Get dirty[guru]
This is how I have it all done.
Answer from -=chess=-[guru]
you can if you know how to do it - simply you need to dilute the tile adhesive on a primer without water and putty all the walls after drying, you can simply prime it and - you can glue the tiles onto a tongue-and-groove block
Answer from Sergey[guru]
The plaster must first be isolated. You can do the same tile adhesive plaster a plaster wall. Only first you need to make notches on it for good adhesion.
Answer from Yotas Shabanov[guru]
I would line the wall gypsum plaster, then tiles
Answer from Yergey Krishtofenko[guru]
First, build up the partition. Then reinforce it with strobe mesh. This is a fiberglass mesh similar to serpyanka, only sold in meter-wide rolls and without an adhesive layer. Take one with a cell of 5*5 mm. Shoot this net to the wall construction stapler. Like wallpaper, only with a 10cm overlap between the sheets. You don't have to shoot too accurately. The main thing is that it stays on the wall and the staples do not stick out from the plane of the wall.
Next, coat this mesh with gypsum plaster. Dilute it a little thinner than usual and spread a thin layer over the entire wall with a wide spatula.
After drying, plaster with the same gypsum plaster in the required layer.
Let it dry thoroughly. Next, glue the tiles.
You need to prime before the strobe, after the strobe and after plastering.
If something is not clear or additional information is needed. information - write :)
Answer from dancer[guru]
Who will stop you from doing this?)
but be sure to think about waterproofing (can you imagine what happens to drywall when it gets wet), choose high-quality glue (or better yet, use good cement, which is suitable for laying tiles, for example, “Master”) and remember the distance between the tiles. By the way, you can also build up the wall using cement mortar. Good luck!
Answer from Yokarificator[guru]
Waterproof the shower area and glue the tiles with reinforced adhesive. The wall can be extended.
Answer from Val Franco[guru]
You can do it without waterproofing, but then your shower will look like in the last photo...
Tongue and tongue slabs are presented on the market today in a wide range. However, Knauf products are one of the most popular. This is due to many factors.
Reviews of tongue-and-groove slabs
Knauf tongue-and-groove slabs are rectangular blocks, the dimensions of which are 667x500x80 mm. To connect the elements together, a tongue-and-groove lock is used, which is made from building gypsum and binding components.
The described products are used for the construction internal partitions and cladding of house walls. The versatility is very popular with consumers. Among the additional advantages of the described slabs, buyers highlight the opportunity to reduce the cost and labor intensity of laying partitions when using such products. Confirmation can be specific example: tongue-and-groove slab replaces red brick in the amount of 20 pieces or 14 pieces of sand-and-a-half bricks.
Among other things, gypsum boards provide excellent thermal insulation. Consumers emphasize that the 40-cm concrete wall. Buyers quite often choose these slabs for the reason that they provide economic benefit. Installation can be carried out by gluing or using dry technology.
Plastering work is excluded, the front surface of the products is of high quality. It is only necessary to seal the seams and sand the base. During installation, there is no need to use special equipment. Consumers point out that tongue-and-groove slabs Knauf can be used to hammer nails easily. In general, this material is easy to process: it can be planed, milled, and sawed. Therefore, the issue with laying the pipeline and electrical wiring disappears. After installation, according to consumers, the wall is immediately ready for painting, wallpapering and tiling. The partition occupies a smaller area compared to a brick one.
Why choose a tongue-and-groove slab from Knauf
If you are still undecided whether the described slabs are suitable for you, then you should consider their additional advantages. Among others, one can highlight a high sound insulation coefficient, which reaches 41 dB. When constructing openings within 0.9 m, there is no need to reinforce the upper part with a lintel beam. The formed walls are able to reflect noise waves, in addition, they act as a dielectric.
Knauf tongue-and-groove boards have the same acidity as human skin, and the material has no odor. It can be used to construct single and double partitions, the latter of which require a 4 cm air gap. Everything will depend on the noise protection requirements.
The plates are installed with high precision and connected to each other as firmly as possible. Internal walls able to bear weight kitchen cabinets, shelves and plumbing fixtures. In this case, there is no need to strengthen the surface. Knauf tongue-and-groove slabs have additional advantages, among which are:
- fire resistance;
- vapor permeability;
- environmental friendliness.
Technical characteristics of moisture-resistant solid slab 100 mm
As an example, before purchasing, you can consider Knauf moisture-resistant tongue-and-groove slabs. Among others, a 10 mm product should be highlighted, which has a gray or green color. The raw material is G-5 gypsum.
The compressive strength is 5 MPa. The thermal conductivity coefficient can reach 0.29 W/m °C. As for the flexural strength, it is equivalent to 2.40 MPa. Fire resistance limit - 2.5 hours. The size of the slab is 667 x 500 x 100 mm. Sound insulation is kept at 41 dB. Such solid tongue-and-groove slabs "Knauf" are manufactured according to technical specifications 5742-007-16415648-98. The wholesale price is 250 rubles. a piece.
The mass of the plate is 38 kg. Its density is 1250 kg/m³. The volume of one block is 0.03 m³. The above-mentioned sound absorption coefficient is one of the best indicators among all categories of this material. Partitions constructed from the described slabs are most often used in rooms with high humidity. Among these are:
- kitchen;
- toilet;
- bathroom.
Key Features
The increased thickness of the product allows you to hide pipes, communications and wires of impressive diameter inside. This feature is relevant for bathrooms and other rooms where there is a large number of plumbing communications.
Using such Knauf tongue-and-groove slabs, the price of which was mentioned above, you can no longer worry that sounds from the toilet or bathroom will disturb you in your living space. And the shelf will not collapse if you install it on such a surface. Partitions can be erected up to a height of 3600 mm, and no additional support frame is required. The manufacturer refers these plates to the premium class.
Glue for PGP "Bolars"
If you decide to install Knauf tongue-and-groove gypsum boards, you should worry about the presence of special glue. As an example, we can consider the Bolars composition, which is sold in 20 kg bags. You will have to pay 215 rubles for such a volume of material.
It is a special mixture for installing plasterboard and gypsum fiber sheets, gluing mineral wool slabs to vertical surfaces. Joints can be sealed with this adhesive. It has a gypsum base and is made using highly effective additives.
Advantages of glue
Application of glue for tongue-and-groove slabs is carried out manually. Among the advantages of this composition are:
- quick fixation of slabs;
- reasonable cost;
- highly elastic structure.
Thanks to the latter property, the glue is very convenient to use. It is sold dry and packaged in paper bags. The composition is manufactured in Russia, therefore it has an affordable price for the consumer. The material has a wide range of uses, because it can be used to install not only tongue-and-groove slabs, but also plasterboard and gypsum fiber sheets.
Glue characteristics
Adhesion is 1 MPa. Operating temperature varies from +5 to +40 °C. It is recommended to use the composition in bathrooms and living rooms. It is suitable for fastening insulation and gypsum tiles.
Before purchasing glue for tongue-and-groove slabs, it is recommended to calculate the required volume of material. Using the volume of one bag, you can install 35 slabs, which is true for products with dimensions that are 66 x 78 x 5 cm. The thickness of the seam should be 2 mm. You should prepare the amount of solution that you can produce in 40 minutes. The time for on-site correction of the product is 15 minutes.
Conclusion
PGP "Knauf" can be used not only for the formation of traditional wall partitions, but also for fastening products to ceilings. These canvases quite often act as acoustic barriers and are attached using direct hangers, combined and vernier clasps; you can use the technology that is convenient for you. If the base is load-bearing wooden floors, then Knauf self-tapping screws should be used. In the presence of reinforced concrete floors You will need ceiling dowel-nails from the same manufacturer “Knauf”.
From leading Russian and foreign manufacturers affordable price. The products presented in our catalogs, and in particular the glue for pgp, the price of which depends on the type of mixture, fully comply with all quality and safety standards.
Buy glue for tongue-and-groove slabs possible in online mode directly on our website, and thanks to our delivery service, the client does not even have to leave home. All goods ordered in the store will be delivered to the specified address directly on the day of purchase.
Gypsum adhesive for pgp - features and composition
Installation adhesive pgp is a universal gypsum-based installation mixture that allows you to quickly, efficiently and reliably fasten tongue-and-groove slabs, while ensuring high quality masonry. The adhesive for installation of pgp, as a rule, includes the following components:
- Gypsum.
It is the main binding element of almost any adhesive for tongue-and-groove slabs, the price of which depends on many factors. It is thanks to the gypsum binder that gypsum adhesive for installation of pgp provides the necessary strength for high-quality and reliable masonry.
- Quartz or fine sand.
This component in the adhesive for pgp, which you can buy right now, acts as a filler, significantly reducing the cost of production of this mixture and the market price of gypsum adhesive for pgp installation.
- Chemical additives, additives, modifiers.
These components make it possible to significantly increase the ductility of the adhesive for installing pgp, as well as extend the viability of the finished solution, which is important when working with large volumes of masonry.
The main purpose of glue for pgp
As the name implies, glue for pgp is moisture-resistant and regular and is used exclusively for laying tongue-and-groove slabs, which you can also purchase in our online store website. In addition, glue for pgp, which anyone can buy today, can be used for laying gas silicate blocks, and any wall blocks based on cellular concrete. Thanks to its unique composition, moisture-resistant adhesive for pgp perfectly withstands the effects of chemical elements and is not susceptible to fungus or mold. High-quality glue for pgp, the price of which can vary widely, is the key to the strength and reliability of the walls of the building.
Use glue for pgp during installation interior partitions in apartments or private households. It should be noted that the adhesive for pgp is moisture resistant and can be used when arranging partitions in rooms with high levels of humidity, such as a bathroom, toilet, etc.
Buy glue for tongue-and-groove slabs in Moscow
Online store site, offers to buy glue for pgp and others building mixtures wholesale and retail in Moscow and the Moscow region. With us, you will find everything you need for repairs and construction at the best prices in the region. You can buy glue for pgp by adding the product to your cart, or by calling the numbers that you can easily find in the “Contacts” section. It should be noted that we deliver purchased goods throughout Moscow and the region; you can find the terms and delivery costs in a special section.
Description of material
Mounting adhesive - dry gypsum mix gray, which is based on gypsum and chemical additives, is intended for installation and sealing of joints of gypsum tongue-and-groove slabs, gluing decorative elements and gypsum-based products. Glue is well suited for eliminating flaws and pits on the walls.
Material consumption
Installation of tongue-and-groove plates - 11.5 kg / m²
Conditions of work
The temperature of the air and the base during work should not be lower than +5˚С. The temperature of the mortar mixture should be from +10˚С to +30˚С.
Mortar preparation
Pour the contents of the package into a container with a pre-measured amount. clean water room temperature. Mixing ratio: 25 kg of dry mixture requires 15 liters of water. Mix everything slowly until smooth. Let the mixture stand for 2-3 minutes for better dissolution, then mix again. With repeated mixing, it is allowed to add water to the desired consistency.
ATTENTION!
It is necessary to use only clean containers and tools to avoid deterioration and change in the properties of the solution. It is prohibited to introduce additional water into the finished mortar mixture.
Operating procedure
The finished solution must be worked out within 30 minutes. When performing work, it is necessary to avoid sudden changes in temperature and humidity. After the installation adhesive has been applied to work surface, you can perform, if necessary, re-application, but only after the first layer has completely dried. Immediately after the solution is completely used up, the container and tools should be thoroughly washed with water.
Storage conditions
Store bags of dry mixture in covered, dry rooms on wooden pallets.
Manufacturer's Warranty
Guaranteed shelf life in undamaged manufacturer's packaging is 6 months from the date of manufacture.
Tongue-and-groove slabs are a gypsum material that is used to construct partitions in buildings, public complexes, etc. Used for the construction of structures in rooms with normal humidity.
Due to their resistance to moisture, some boards can be used in areas with high humidity. During the manufacturing process of products, special additives are placed into the molding mass to reduce “water absorption.” Such slabs, as a rule, have a special color.
Using the right type of adhesive, it is very easy to install tongue-and-groove slabs, while ensuring high efficiency of the construction process. The use of tongue-and-groove slabs avoids the need for plastering the surface. By supplementing the installation of slabs with special binders, you can ensure increased adhesion and greater resistance of the coating to cracks.
To work with tongue-and-groove slabs, you will need a special glue, which is made on the basis of an ordinary gypsum mixture. Thanks to the use of special glue, it becomes possible to significantly strengthen the structure of tongue-and-groove slabs.
Popular types of glue for working with gypsum material
In the building materials market in modern times, there is a huge assortment of different types of adhesives for slabs. If you don’t know which glue is suitable for your design, you can easily get confused in this variety. On this moment There are several brands that have already proven themselves well.
"Volma-montage"
The photo shows that the first type of installation adhesive can be classified as “Volma-montazh”. The composition of this type of glue is made of gypsum binder, which combines well with a variety of mineral-based additives. The use of this glue allows you to achieve high-quality adhesion, retain moisture, and also perform installation lightweight slabs due to the simplicity of the preparation process.
We invite you to watch a video that highlights the intricacies of installation gypsum boards.
The use of such glue allows frameless installation tongue-and-groove slabs in a vertical position. In addition, it is possible to strengthen gypsum components, as well as thermal insulation sheets.
"KNAUF Fugenfüller"
Knauf Fugenfüller glue deserves a special place. Glue is a dry putty mixture that is applied to plaster. It is used for sealing joints, as well as for puttying surfaces. Such a product is considered not only economical in cost, but also allows you to simultaneously use the material as glue and putty. If you need to complete construction in a short time, you should use KNAUF Fugenfüller glue.
"Weber.cel gips"
Next we should mention the adhesive “Weber.cel gips”. This is powder white. In the process of its manufacture, gypsum, friction sand and various polymer additives were used. This mixture should be mixed with water during preparation. This durable look adhesive designed to work with drywall, tongue-and-groove boards, and other types of soundproofing materials. Apply with a spatula. After a short period of time after application, the surface is able to withstand heavy loads.
"IVSIL PLAST"
The presented glue is considered an equally popular type. This type is made on a binder with polymer additives. This composition is very effective when working with gypsum fiber sheets.
"BOLARS Gipsokontakt"
Don't forget about this glue. Made on the basis of gypsum sand with the addition required quantity polymer additives. The use of this material allows us to achieve high-quality installation of tongue-and-groove slabs. Its scope of application includes indoor work.
Buying glue to perform installation work, you should rely not only on the qualities of the above manufacturers, but also on cost. Experts recommend purchasing glue only in large construction stores to eliminate the possibility of purchasing counterfeit products. Before you start using glue, you should carefully read the instructions.
