Do-it-yourself cockerel from plastic bottles. Step by step instructions with photos. Do-it-yourself cockerel for the new year Rooster from plastic plates

I would like to introduce you to the cockerel Petrunya.
Not a single yard in a village or village can do without this magnificent bird. So I made myself a friend, a bright and majestic owner of the yard!

I will be happy to share with you the stages of its manufacture (based on the idea of making birds from plastic bottles Alena Zinovieva).

To make a mold, we need:
1) 5l. canister (I use from under liquid soap),
2) 5L plastic bottle,
3) metal-plastic pipe (height of legs is about 30-35 cm),
4) two 1.5l. plastic bottles for "thighs",
5) self-tapping screws, scissors, stationery knife, screwdriver.

For fastenings, I use these self-tapping screws (I buy by weight in hardware stores).
Small (about 1.5-1.6 cm) - for attaching feathers and component parts to each other.
Large (about 5-6 cm) - for attaching the head to the neck.

1) Move the top of the canister about 3cm.
2) We bend the metal-plastic pipe (we give the shape of the legs), in my case - the rooster is walking ( right leg pushed forward), and fasten it with screws to the canister.
3) For the neck, from 5l. bottles, fold the envelope, fasten it to the canister with screws.
4) From 1.5 l bottles we cut out two "thighs", which we attach to the canister with self-tapping screws.

For feathers, I used bottles like this. We cut off a long neck, cut the bottle into 5 feathers (we focus on the protrusions on the bottom of the bottle), use the upper part of the feathers.

We begin to close the body with the "thighs". Detach them from the canister for convenience.
1) attach the corrugated tube to the neck of the bottle,
2) attach the feathers with wire.

We attach the finished legs back to the canister.

Starting from the back, we close the entire body, except for the back, with feathers (we fasten it to the canister with screws). We leave the back of the neck open, because there will be other feathers.

The next step is to start making paws. From copper wire 2.5 mm (or any other, preferably rigid, but not steel, which bends), we bend the shape of the paws (for more details, see MK Filin). From the corrugated tube we create the effect of paws. The left tail is inserted between the metal-plastic pipe and the corrugated tube. From below, you can still pour glue for strength.

Cut out claws from the bottom of the bottle (photo). They should be narrow and long. We fix them with glue (I use "Installation Moment - Liquid Nails").

We paint the torso and legs with spray paint (I use universal enamel from the KUDO company).

We cut out the head from construction foam using a clerical knife, it is very sharp and the cuts are even, not torn. If the cutting process seems complicated to you - cut out all the details separately! Then they can be glued together.

With the help of sandpaper (medium) we bring to the shape we need.

We process the surface with acrylic putty, wait for complete drying and once again skin it to smoothness. After that, we process it with ordinary PVA glue, so the paint fits very well.

We begin to paint the head (you can use acrylic paints, it's more convenient). Glue the eyes (bought in a fabric store).

After fitting the head to the body, the husband said that the comb turned out not to be a rooster, but more suitable for a chicken. Decided to redo. I made a pattern out of paper (I tried it on for a long time so that it was larger). I transferred it to the foam, cut it out and glued it in place of the former.

With the help of wire, we begin to fasten the long feathers of the wing. The back stays open.

I close the top of the wings with such feathers from corrugated 1.5 liters. bottles. The last row goes to the bend, into the inside of the wing.

We paint with paint, let it dry well and attach it with perforated tape (sold in any hardware store) and self-tapping screws to the body. We bend the net for attaching the tail (you can increase its length and the tail will turn out to be richer).

Let's start making the tail.
We cut feathers from 2l or 2.5l. bottles in 5 parts. We paint separately on both sides (at first I applied black, after drying a little blue)

We attach to the grid with a wire. After coloring, I cut the feathers in half again, so the tail turned out to be more magnificent.

For the feathers on the back, I cut feathers of different lengths from transparent bottles (it's easier to dye yellow), about 2-2.5 cm wide. Attached to the back with self-tapping screws, 3-4 pieces at once.

I will be happy to share with you the stages of its manufacture (based on the idea of \u200b\u200bmaking birds from plastic bottles by Alena Zinovieva).

1) Move the top of the canister about 3cm.
2) We bend the metal-plastic pipe (we give the shape of the legs), in my case, the rooster is walking (the right leg is extended forward), and we fasten it to the canister with screws.
3) For the neck, from 5l. bottles, fold the envelope, fasten it to the canister with screws.
4) From 1.5 l bottles we cut out two "thighs", which we attach to the canister with self-tapping screws.

For feathers, I used bottles like this. We cut off a long neck, cut the bottle into 5 feathers (we focus on the protrusions on the bottom of the bottle), use the upper part of the feathers.

We begin to close the body with the "thighs". Detach them from the canister for convenience.
1) attach the corrugated tube to the neck of the bottle,
2) attach the feathers with wire.

We attach the finished legs back to the canister.

Cut out claws from the bottom of the bottle (photo). They should be narrow and long. We fix them with glue (I use "Installation Moment - Liquid Nails").

We paint the torso and legs with spray paint (I use universal enamel from the KUDO company).

With the help of sandpaper (medium) we bring to the shape we need.

We process the surface with acrylic putty, wait for complete drying and once again skin it to smoothness. After that, we process it with ordinary PVA glue, so the paint fits very well.

We begin to paint the head (you can use acrylic paints, it's more convenient). Glue the eyes (bought in a fabric store).

With the help of wire, we begin to fasten the long feathers of the wing. The back stays open.

I close the top of the wings with such feathers from corrugated 1.5 liters. bottles. The last row goes to the bend, into the inside of the wing.

We paint with paint, let it dry well and attach it with perforated tape (sold at any hardware store) and self-tapping screws to the body. We bend the net for attaching the tail (you can increase its length and the tail will turn out to be richer).

Let's start making the tail.
We cut feathers from 2l or 2.5l. bottles in 5 parts. We paint separately on both sides (at first I applied black, after drying a little blue)

We attach to the grid with a wire. After coloring, I cut the feathers in half again, so the tail turned out to be more magnificent.

For the feathers on the back, I cut feathers of different lengths, from transparent bottles (it’s easier to dye yellow this way), about 2-2.5 cm wide. Attached to the back with self-tapping screws, 3-4 pieces at once.

If you want to decorate your yard, garden or garden in an original and unusual way. country cottage area, but do not want to spend money on expensive Consumables or buy ready-made factory products, then try to make figurines from various improvised means with your own hands.

Plastic bottles, corks, old car tires- all this is an excellent raw material for the manufacture of beautiful things. A motley and bright rooster - the owner of the yard, who can simply “guard” the yard, and perform the functions of a weather vane, will become a real decoration of your dacha.

There are many master classes that show in detail or give instructions on how to make such interesting decor And what you need to do. Inspired by the ideas of the masters, you can easily craft from unnecessary things and waste material very beautiful products.

Making a cockerel from plastic bottles

Plastic bottles and corks are practically the most affordable and cheap material to create crafts. In addition, its pliability is a big plus - plastic is easily cut. with an ordinary knife or scissors, and if you need to round the edges or smooth the surface, then this can be done with a regular iron.

The bottles themselves come in many colors, but a wider range of colors is very easy to obtain using spray cans. various paints to your taste.

You can start by making simple shapes.

Take as a basis large bottle(usually five liters). You can paint with either paints or TEX enamel. Cut off its bottom, and bend the edges inward.
The head can be made from papier-mâché, or you can also use a bottle (you will need its lower part). In the second option, you will also need to make a beak for the rooster - this can be a bottle cap on which you attach the blank.
The paws are made either from corrugated hose, or from old tubes, or from wire wound on transparent tubes.
For feathers and a tail, you need to cut a lot of strips (you can cut ribbons in a zigzag pattern or each piece individually). It is advised to fix it with glue and adhesive tape, self-tapping screws (there should be a foam or wood lining inside the figure).
Cut a scallop from the bottom of the bottle and attach it to the cockerel's head. Wings can be made from halves of two bottles.
Color the product using different colors and shades to make the bird colorful and bright. You can take a quick-drying bronze varnish, colors, to make it even more spectacular.
Cut out the eyes from the same plastic and paint or draw. You can decorate them with eyelashes.

Such a rooster made of plastic bottles will look great on a wattle fence, on a pole or a fence in your country house, and even serve as an original weather vane.

From bottles and cardboard, you can simply build a frame for a future bird, and then model a papier-mâché rooster figurine on it. Do not forget to dry each layer thoroughly, and then paint the product and cover it with yacht varnish.

And here is a more complex master class for making a cockerel, however, as a result of all the efforts, you will get a real sculptural masterpiece.

First you need to prepare the form - the basis for the future figure. The master offers to build it from five-liter plastic cans and bottles. This will be the neck and torso. For the legs of the bird, you need to take metal-plastic pipes, about thirty centimeters high, plus two bottles of one and a half liters each for the thighs.
To fasten the parts to each other, you will need large and small self-tapping screws.
Connect the elements of the base to each other: attach metal-plastic pipes the shape and position of the legs, move the upper part of the canister a few centimeters and roll the envelope out of the bottle to make a neck. And also cut out the thighs and attach them to the canister.
Five feathers can be cut from one large bottle. Only first you need to cut off from its long neck. You will need the top of the feathers.
Cover the figure with plumage starting with the thighs of the cockerel (you can detach them to make it more convenient. And when you are done, attach the legs back). Then follow from the back and attach the feathers with self-tapping screws everywhere, except for the back and back of the neck (you will need other plumage there).
Weave the paws from hard copper wire and supplement them with corrugated tubes (there should be a hole in the middle through which you need to insert a piece of wire to attach to the legs).
Cut the claws from the bottom of the bottle and attach them to glue or liquid nails.
Paint the finished part of the bird (KUDO paint or enamel).
Now it's time to do the cockerel's head. For its manufacture, it is recommended to use construction foam (parts can be cut out separately and then glued. Use a clerical knife to cut). To give a head desired shape You will need medium sandpaper. Then the part will need to be treated with acrylic putty, and when it dries, sand it well. When you achieve the necessary smoothness, go over it with glue (regular PVA is also suitable). Only after complete drying it will be possible to start painting.
You can also paint your head with acrylic - it's much easier and more convenient. Pick up cockerel eyes in the fabric store and glue them into the holes.
The shape for the wings is cut out of the mesh using side cutters. Attach long feathers to it, leaving the back open. From above, you can also add plumage cut from corrugated bottles. Paint the new elements and let them dry. Then attach to the body using self-tapping screws and perforated tape.
For the tail, you will need to cut a lot of feathers and color them. Fasten to the protruding part of the mesh from the wings (if you bend it, the tail will turn out to be more magnificent and luxurious).
Now close the back. To do this, cut out a lot of feathers of different lengths and fasten them in several pieces in rows. It is better to fix the last row with glue so that the hats of the self-tapping screws are not visible. For the back of the head and sides of the head, use already fine plumage.
Color the new plumage by first covering with construction tape and bags those parts of the cockerel that have already been painted earlier.
Insert spurs into the legs of the bird and cover it with glossy varnish.

If you want to unusually decorate a site or a house, there is no need to spend money on expensive sculptures or consumables. From various improvised means, you can make a figurine of a funny bright cockerel.

Plastic bottles and corks are the most affordable material. Big Advantage- compliance. Such plastic is easily cut with a knife or scissors, and you can use an ordinary iron to round the surface and edges.

From plastic bottles

You can use multi-colored bottles to make crafts, or you can achieve a suitable colors using spray cans with paints or enamel "TEX".

Prepare in advance:

several empty plastic bottles;
wire or old corrugated hose;
Styrofoam;
scotch;
self-tapping screws;
glue;
paints.

How to make a rooster from plastic bottles? An empty five-liter bottle is taken as the basis for crafts. The bottom is cut off from it, the edges are bent inward.

The cockerel looks great on the fence of the cottage or serves as an original weather vane.

There is another option for making a cockerel from plastic bottles: a master class designed for beginners. The craft does not require special skills.

Prepare in advance:

three brown plastic bottles;
disposable cups and plates of yellow and red colors;
yellow ball for dry pool;
double-sided tape, regular tape;
stapler;
black marker.

Cut off the tops of the bottles and fasten them together.

There is a more complicated option. It makes it possible to get a real sculpture on the site.

For work you will need:

They begin with the manufacture of the torso and neck of the future sculpture. They are made from five-liter and one and a half liter bottles. Pipes are used to make legs. For thighs, take a one and a half liter bottle.

Self-tapping screws of various sizes are used to fasten parts to each other.

The pipes are shaped and the desired position of the bird's legs. Move the top of the bottle a few centimeters and roll up the neck wrap from the second bottle. The hips are cut out and attached to the base with self-tapping screws.

Feathers are cut from parts of the bottles along the entire length. They close the body of the bird, starting from the bottom. It is best to attach the feathers to the wire. The torso is closed, leaving the back part of the neck open. A different kind of feathers are attached there.

Bend the wire for the paws. The hose will complete the further shape. A tail is inserted between the pipes and everything is fixed with glue. Cut long and narrow claws from the bottom of the bottle, fasten with glue. Paint the sculpture with a can of paint.

While the torso with legs dries, make the head. It is cut out of foam using a clerical knife. Cuts must be sharp, but not torn. You can cut the head in parts, and then fasten them with glue.

Irregularities are removed with sandpaper. Then the surface is treated with acrylic lubricant. Apply a layer of ordinary glue, wait for it to dry completely. After that, paint the bird's head acrylic paints make eyes.

Attach the head to the body. Prepare the shape for the wings. Attach them to the back of the bird, leaving it open. Coloring.

For a tail from a two-liter bottle, feathers are cut along the length, dyed on each side and attached to the body with a wire. At the end of the work, short feathers are cut, a couple of centimeters in length, fastened to the back with self-tapping screws.

Complex option, takes a lot of time. But the end result is a real masterpiece.

Plywood figurine

You can make a cockerel out of plywood. Such work can be done even by a schoolboy.

Ready for work:

Making a cockerel with your own hands- work for diligent and patient. It requires attention, time and effort. But with the desire and patience, everything will work out for beginners. The main thing is to follow the step-by-step algorithm.

To color the product, take bright colors. At the end of the work you can cover the cockerel with varnish. When using acrylic paints varnishing is not needed.

From bottle caps

To make a rooster from corks from plastic bottles, prepare a diagram in advance. Suitable option for cross-stitch or beadwork. The final work will be very impressive.

Dial the desired number of caps of the desired colors. You can line the surface for accuracy, as in the diagram. Glue corks if the panel is horizontal, or nail them if the work is vertical. Lids are easier to attach reverse side. They hold on tighter, and the cockerel turns out to be especially spectacular from a distance.

If suddenly there were not enough covers of any colors, acrylic paints will solve the problem. In places where it is impossible to nail a cork, they are fixed with a gun or glue.

After completion of work, auxiliary lines are removed.

The application can be made on outer wall or inside the apartment.

From old tires

Old car tires are a great starting material for creativity. The dacha will be decorated with a motley cockerel. Prepare a pair of tires, two polyethylene tubes, a piece of plywood for small parts.

The torso of the bird is made from one whole tire, the second is used partially for the manufacture of the tail. Tubes are taken for the legs of a rooster.

To cut tires, use a hacksaw for metal or an electric saw. A sharply honed large knife will do. wooden details easier to cut with a jigsaw. But it is much more convenient to use plastic instead of plywood.

Fasten everything with bolts and wire. Inserted into the legs metal fittings so that the rod enters the ground at one end, the second is attached to the hole in the tire. Then the sculpture is not afraid of bad weather.

A do-it-yourself rooster made of wood is a task for a real master. You will need special knowledge and the ability to work with the instrument, to feel the material. It is very difficult for beginners to cope with such work. Even detailed master classes will not give without certain skills the opportunity to make a truly beautiful product the first time from wood. A plastic bottle is an easy-to-work and simple material. TO creative work even children can be involved.

Attention, only TODAY!

Making a rooster from plastic bottles with your own hands is easy, step-by-step instructions are proof of this. The first version of the craft is perfect for working with kids, and the resulting souvenir will look great at home or on the site. The second craft from this material is already a more complex manufacture of crafts that requires certain Additional materials and knowledge.

Now you can start making paws, for which you need copper wire. It is necessary to bend the shape of the paws, and then create from the corrugated tube desired effect. Insert the tail between the two tubes and, for strength, fix everything with glue. Cut out the claws from the bottom of the bottle, they must be long and narrow, attach using glue. Using a can of paint, paint the existing parts of the cockerel.

While the torso with legs dries, you can start creating the head. First, it should be cut out of foam using a stationery leg. Cuts should be sharp, but in no case torn. If it is difficult to cut the head right away, you can cut out its parts separately, and then fasten it with glue. Sandpaper it will help to remove irregularities, and after that treat the surface with a lubricant for acrylic. Then apply a layer of ordinary glue and, when it is completely dry, paint the bird's head with acrylic paints, make eyes.

Now try on the head to the body. Prepare the form for the wings and attach the long wings to the back, while leaving it open. Color everything, make a tail. To do this, cut long feathers from a two-liter bottle, paint them on both sides and attach to the body, again using wire. To finish the feathers on the back, cut 2 cm short feathers from the bottles, attach them to the back, you will need self-tapping screws for this.

Step-by-step instructions one or two will help you make a rooster out of plastic bottles with your own hands. The first version of the craft is easy, requires a minimum of source materials, and such a cockerel can be made even with kids. The second bird is large, serious and delightful appearance. If you want to build it, it should also work without any special problems. Easy and quick craft -