How to make a swan out of a tire. How to make a swan out of tires: cut out crafts from old tires How to cut a swan out of tires

You can also decorate a garden without purchasing sculptures in a store using improvised means, as many experienced and economical gardeners do. Some use plastic bottles, others use old things and objects, and still others use wheels. One of the most popular figures made from tires is the swan. Making a swan out of a tire with your own hands is easy, you just need to know a few important points.

The product needs a tire that has already been used, such material will be softer and more pliable. The cord on the tire is cut because of its stiffness. It is better to choose a wheel with cars domestic production. Wash with soapy water and dry before use.

You can make a swan from tires in several ways, as well as supplement them. Usually, a cut-out option is used, without separating parts of the tire, but completely twisting and strengthening the bird's neck. But, many gardeners, wanting to have on the site not only beautiful decoration, but also functional, use lighter options, leaving most tires free for planting. It will take from one to two hours to make any of the options.

Here's what to consider before making a tire swan:

In the manufacture of products, especially if electrical appliances are used, safety precautions should be observed, as well as gloves and goggles should be worn so that pieces of material do not get into the eyes.
Cut out the product outdoors, then that when using a grinder and a jigsaw there will be a lot of smoke and bad smell come from the tire.
It is better to cut the cord - this is the inner part of the tire, which holds the entire structure tightly. If it is not cut, then it will be more difficult to make a bird.
The tire must be of an old production, they are softer, without spikes and additional metal structures, additional metal reinforcement on the cord.
For easier cutting, it's best to choose a tire with a tread pattern that roughly matches the pattern, such as rectangles.
When the bird's neck is cut out, a bar can be placed under it to help support it, and it will be more convenient to cut it off. An old tree stump can serve as the same support. It is better to start the cutting process from the base of the neck to the nose, and then continue to cut the neck.
After manufacturing, it is better to install the bird on another tire or dig a shallow groove under it so that it has stability.
Paint for the animal is chosen one that will be resistant to weather changes. For example: for facades or enamel, automotive spray paint, forging.
If the tire was with a metal cord reinforcement, then the edges of the product must be treated with a grinder so that sharp edges do not cause bodily harm (cuts) in the future.
It is better to apply the paint in 2-3 layers, after each time allowing the previous layer to dry well, then such decoration will not need to be processed for 3-4 years.

Schemes, drawings of swans from tires:

Tools and materials

For manufacturing you will need:

chalk or marker;
tire - for one bird - 1 pc.;
paint - white or black, for the beak red or any other;
plywood for the nose, if you make a bird from the second option;
jigsaw;
screw and nut, rivets, self-tapping screws - any material that will help fasten 2 parts of the tire;
Bulgarian;
pliers;
drill;
wire staples or clamps;
wire - wire rod;
roulette;
knife, but not a kitchen knife.

Video on how to cut a swan out of a tire:

Option 1

Step by step instructions on how to make a swan from a car tire:

On the tire, draw with chalk (or a marker in a contrasting color) the contours of the bird.
Visually divide the wheel into 2 equal parts, one is the neck and head, the other is the body, in this proportion the bird will have a more aesthetic appearance.
The markings should occupy the entire part of the wheel so that the nose of the bird rests on the tail pattern.
The width of the neck is 7-10 cm, the head is 10-14 cm. The neck needs to be expanded by 1-2 cm towards the body.
The tail is drawn in the form of 2 triangles or one large one, and 2 small ones on the sides.
When marking the body, not only even strokes are used, but can also be done in the form of small wavy or zigzag lines.
After the prepared drawing, take a jigsaw or a sharp thick knife (for example, such as for hunting a bear).
Exactly following the applied pattern, start cutting out the swan from the head. To do this, you need to pierce the tire in the nose area.
You need to cut in parallel, moving gradually a few cm from one side, then from the other side.
After the bird has been cut out, the tire should be turned out. It is better to do this together with an assistant, but you can do it yourself. Then you should put the neck with the head of a bird inside on the ground and put your feet on one of the wings. Push the middle of the tire as hard as possible down to the ground, while you can press down with your feet.
After it is possible to push through the middle, the bird will acquire a certain shape of the body with wings, after which the head must be fixed.
From the head to the tail, make parallel holes with a drill so that you can attach a reinforcement rod that will support the head and neck.
Insert staples made of thick wire into the finished holes.
Prepare a rod - from a wire rod, about 6 mm, bend it in a semi-arc.
Attach from tail to head and secure with staples.

When everything is fixed, the head can be deployed and turned into the desired position, and then proceed to decorating.

Option 2

How to make a flowerbed swan from a wheel:

Clean the tire and apply the pattern, it should be applied only on one side of the tire.
From one edge we draw a heart shape, where a triangle should be left at the cut site. The drawing itself should occupy more than 3 parts of the side.
Make a cutout according to the marking with a knife.
Several holes need to be made along the edge of the tire, after cutting a semicircle, make cuts to make it easier to turn the tire out.
When the semicircle is cut out, it needs to be turned out, and the rest of the tire.
Fold a semicircle - this will be the neck, fasten the 2 halves of which with a screw and nut.
Cut a triangle out of plywood - this is the bird's beak and attach it to the neck with self-tapping screws.

The flower bed is ready, it remains to paint and pour the soil so that the plants can be planted.

From any carved bird, you can make a flower bed. For example, if you cut a swan according to the first version, it is installed on a larger tire, into which soil is poured, and the bird is slightly buried in it. A small layer of earth is also poured into the lower part of the body, as if comparing the level of the embankment.

Creeping or undersized plants are planted in such a design, those that bloom look most beautiful. blue flowers, depicting the water surface: periwinkle, creeping thyme, subulate phlox, veronica, ivy. And if you install it on a hill, then you can use it for decoration ampelous plants: petunia, begonia, kampsis, dichondra, lobelia.

Usually, when making one bird, the craftsmen also make the second one, because, as you know, the swan is a paired bird, a symbol of family and fidelity. Therefore, it will be beautiful to arrange a whole family of birds on the site or make a sandbox for a baby.

A master class on how to make a swan out of a car tire with your own hands:

Do-it-yourself tire swan scheme, step-by-step instruction and master class. The swan is a beautiful, graceful bird, but it is loved not only because of such qualities. She is a real symbol of love, tenderness, inseparability, purity.

Therefore, many people often make crafts in the form of swans from paper, wood, plastic bottles, ice and many other materials. Another interesting material is a car tire.

What you will learn from this article:

Let's look at how to make a swan out of a tire step by step.

1 What tools do you need
2 Tips for choosing tires
3 Step by step instructions
4 Where and how to place
5 Photo gallery for ideas and inspiration

What tools will be needed

To make a beautiful and graceful swan out of a tire with your own hands, you should approach the lesson with responsibility and prepare the necessary items in advance. You will need the following materials and tools:

tire without spikes;
jigsaw or knife;
paint - white or any other, as well as yellow and black;
brushes for painting;
metal staples;
drill or sharp nail;
elastic wire or metal rod;
pliers.

If you want to carve one swan out of a tire with your own hands, then one tire is enough, if you want to make a cute couple or a whole company, then, of course, the quantity car tires should correspond to the number of "feathered" copies.

It is best to use worn, frayed, old car tires. It is with such material that it is easier and more convenient to work. It is also optimal to use domestic products.

You should not make a garden decoration with your own hands from foreign-made tires, with spikes, with a metal cord.

Before you start, you need to clean the material from dust, dirt, let them dry.

Do-it-yourself tire swan step by step

A creative event requires caution and care. Before starting work, put on thick gloves and goggles. And follow the step-by-step instructions on how to cut a swan out of a tire:

Take the tire and make a mark with chalk on which you will cut out a beautiful bird. The future type of decoration depends on this scheme. First you need to divide the wheel into two parts, mark the head and neck, they must correspond in length to half the wheel. Then outline the body, wings, tail. A photo with a swan layout scheme will come to your aid:

Then you need to cut the swan out of the tire, for this you can use a jigsaw or a sharp knife. You need to cut according to the diagram drawn in chalk.

Advice! Do not cut one side first and then try to do the other. The process will be very time consuming and inconvenient. It is recommended to cut the swan in parallel, working on each side.

Cut out? Let's start giving a realistic shape to the bird. To do this, lay the material with the cut side down, step on it with your foot and pull to unscrew the side elements.

Now you need to fix the neck of the swan from the tires, otherwise it will not hold. This can be done according to the following scheme: make two holes along the neck for every 10-15 centimeters (using a drill or a regular nail, if there is no first tool), such holes must also be made in the body of the bird, insert metal staples into the paired holes, fasten wire on the neck and torso, fix it with staples using pliers.
The next step is painting the swan from the wheel. It is necessary to choose stable paints, nitro paint, oil, enamel, car paint in aerosol form. Traditionally used White color, but you can use any other to make a custom bird on the site. The tip of the head should be painted orange or yellow tint to imitate a beak, you also need to highlight the eyes in black or blue, and you can also paint on feathers. Acrylic paints can be used to decorate such details.

Step-by-step instructions for making a swan from a tire

Where and how to place

And now the work on making a decorative bird is behind. Surely the question arises - where is it better to place a swan so that it looks beautiful and organic? Consider some of the most popular and interesting options:

IN artificial reservoir. The swan is a waterfowl, so a pond is its natural habitat for it. And even an artificial tire swan craft will look organically in.

On a blue tire imitating water. It is not necessary to have an artificial reservoir in the country house and garden; you can make an imitation of it from a tire painted blue or blue.

Make a flower bed on a swan. You can place the bird in any prominent part of the garden and make a flower bed out of it with your favorite flowers.

Swan on a stone bed. The product will be interesting to look at any flower bed. How to make such a flower bed, read in this material.

The product can be placed on a bed that imitates a pond. It can be covered with sand, stones painted blue, decorated with plants or flowers.

Photo gallery for ideas and inspiration

Although all the product execution patterns are very similar, you can decorate your garden with an artificial bird in different ways. And all options will differ in individuality and style.

Do-it-yourself swan from tires photo

The photos below prove it:

An elegant decoration for the garden can be done by almost everyone. And the cost of such decoration will be very cheap. After all, old car tires can be bought at a low cost or you can get it for free. But the work requires concentration and effort, following the instructions and job description, but a beautiful bird will decorate your yard for many years. How to make other decorations from old car tires, read in this article.

Do-it-yourself workshops on making a swan from tires

Often, gardeners and motorists have several old tires gathering dust in the garage. Throwing them away is either too lazy, or they are simply stored there with the words: "What if they come in handy." One option for using old car tires is to make a swan out of them. There are two ways to make a swan out of a tire: with and without the tire eversion.

What to use for work?

From the materials we need:

an old tire (it is best to take a "bald" and domestic production; it is also desirable that the tire be without a metal cord, since it will be much easier to cut it);
elastic iron bar or wire (for fixing the swan's neck);
several screws;
white and some red paint;

From the tools we need a sharp knife, perhaps a jigsaw for the most dense places of the swan. And if you still have a tire with a metal cord, then without electric jigsaw not enough. Also, from the tools you will need a drill to attach an iron bar to the swan's neck.

Tire swan: stages of work

Another version of the swan is to make it without turning the tire inside out, then the wings of the bird will be lowered more towards the ground.

Well, if you still have questions, then watch this video:

For many Russians country cottage area- not only a place where vegetables and fruits grow, but also a relaxation area for body and soul. decorative ponds, garden gnomes, flower beds, paths and more - there are a huge number of ways to decorate a garden. IN Lately crafts made from waste, such as plastic bottles and old car tires, are gaining popularity. There are many advantages to giving a second life to things that have served their purpose. Step-by-step instructions for learning how to carve a beautiful swan from a tire yourself will help you make such a craft!

Firstly, it is environmentally friendly, because things will not rot in a landfill for centuries, polluting the environment.
Secondly, it is always nice to create comfort and decorations with your own hands.
Thirdly, it is profitable, such scenery will require a minimum of financial investment, because every motorist's tires wear out. Of these, you can come up with a lot of decorations for the garden: these are small flower beds, fences, artificial ponds and much more. The figures of animals and birds carved from the tire are also gaining popularity. If you decide to decorate your garden plot too, read the master class.

How to cut a swan out of a tire with step by step instructions

To cut a swan from a tire, you need:

Worn out car tire
Saw grinder
Electric jigsaw
Thick wire, rod or steel plate
White and red exterior paints
You should work on the street, as the rubber heats up from the grinder, and this gives off a strong smell of burning
Be sure to wear tight mittens or gloves
Feet must be in closed shoes

We study safety precautions when cutting a figure out of a tire

Getting Started - step by step instructions on how to cut a swan from an old wheel

For work, you need to choose the most old tire, as thin as possible and, as they say, bald. The more worn the rubber, the easier it will be to work with it. If there is a choice, it is better to give preference to a tire with a nylon or nylon cord, rather than a steel one. To do this, the tire itself should not be marked “steel”. The latter are difficult to cut, and they are also traumatic both during operation and during further use: it is better not to put such a bird on the playground to avoid cuts in children.

First you need to draw a “pattern” of the future swan on the tire. Mark a point in the middle and draw a beak from it, smoothly turning into the head and neck of the bird. When working with an R13 tire with a circumference of 1.8 m, the dimensions are approximately as follows: beak length 8-9 cm, head 9-10 cm long and 7-8 cm wide. The neck at the beginning has a width of 4-5 cm and closer to the body thickens up to 8-10 cm. Its length is about 75-80 centimeters.

The body of the swan should remain unlined, and it should not be cut: wings and neck are connected to the head on this part.

Swan carving pattern:

After completing the drawing of the swan from the wheel, the cutting process begins. The grinder cuts quickly, but this heats up the rubber and going strong the smell of burning and soot. Therefore, many craftsmen prefer to make notches for the jigsaw blade using the same grinder, drill or chisel, and continue to cut it out for them. It is convenient to use a blade with a reverse tooth at low speeds. So the material will heat up less, there will be no soot, and control over the process is better due to the low speed of work.

It will be correct not to cut out completely one side, and then the other, but to make small cuts on both sides one after the other. It is much more convenient to work this way, the rubber does not bend so much, moreover, the probability that it will turn out symmetrically increases.

Next, you need to unscrew the workpiece. It's not long, but it's quite hard physically. To do this, you need to put it with the cut part to the ground, press down with your foot and pull up the resulting wings. The result should be something like in the photo.

After that, you should fix the shape of the neck. To do this, it is necessary to make holes in it in pairs at a distance of 15 cm from each other and insert staples of soft wire into them. With their help, attach a rod or steel plate to the bird's neck from above. Next, bend the part so that it resembles the neck of a swan.

After cutting and shaping the swan, all that remains is to install the figurine in the selected area and decorate it. It will be beautiful to make not one bird, but a couple at once. Paint the body with white paint, and the beak with red. Draw eyes or form them from buttons, stones, pieces of rubber.

You can also make a stand from another tire lying on its side. An artificial pond or its imitation, for example, made of stones, will look very handy.

In addition to the swan, you can make other DIY crafts from tires. All it takes is a little imagination and time.

Video on the topic of the article

Very often seen in garden plots various figurines decorating the garden. They are part landscape design, make the garden more expressive, original and attract many interested looks. Perhaps the most popular and most common figure is the swan. Such a figure can be made with your own hands from old car tires. Read about the features of the drainage device on the site.

Swans from car tires in the photo

To create a swan from a tire and plastic bottles, you will need some free time, patience, diligence and, of course, materials to create a figure:

An old tire, preferably well-worn and without studs, will be easier to work with such a tire;
It takes about 40 plastic bottles to make one swan;
Metal grid
A plastic hose, you can take from a vacuum cleaner, it will replace our neck;
The wire for the neck, it is necessary to take a sufficiently thick and strong one, with the help of which the main part of the structure will be held;
A small piece of foam for the head.

The tire must be cut in one place, and the tail of the swan in the form of an acute triangle should be cut from one edge.
The edges are fastened with bolts, on the other hand, for convenience, you can cut the edges of the tire.
We attach the wire to the tire from the side where the neck will be, one end of the wire will be the base for the neck, and the other is necessary to fix the figure of the earth, it must be left a little on the underside of the future swan. Read how to pick up and how much the seeds will cost.
For the construction of feathers:
1. It is necessary to cut feathers from plastic bottles and attach them to a metal grill.
2. Feathers are fixed on the lattice from the outside and a little along the upper edge with inside, in order to ready-made mesh was not visible.
This creates two wings.
A swan head with a beak is cut out of foam plastic and attached to a wire
The hose is also put on the wire and attached to the tire with a self-tapping screw, which is preferably dipped in glue.

The swan layout is ready, now the bird needs to be painted white. The wings can be attached to the tire on both sides using self-tapping screws, or by pulling them together with wire. Using the piece of wire left below, we stick the swan into the ground.

Step by step instructions - how to make a swan from a tire?

Prepare tools:

jigsaw,
electric drill,
wire cutters,
pasatizhi,
saw for metal.

Additional materials:

a metal bar or wire a little more than a meter,
a few pieces of thin wire
chalk for marking,
black or white paint, red for the beak;
brushes.

After completing all preparatory work proceed to the direct creation of the swan:

The tire in its original form is marked with a head with a beak and neck. The length of the neck should be more than half the circumference of the wheel, the length of the beak in length will be shorter by about a cm of the length of the head. These are approximate proportions as tire sizes may vary. How to equip a hozblok with a shower and toilet in the country, read.
Next, we make a hole with a knife or a drill in order to start, you can insert a jigsaw saw and start cutting out the figure.
The sawing process should take place in a below average mode with a reverse tooth, then the rubber does not burn and the metal cord in the tire breaks.
It is necessary to cut out the drawing according to the markup evenly and sequentially, a little bit on each side, since if you immediately cut out one side, it will be more difficult to cope with the second, it will constantly bend.
After sawing out the neck and head, it is necessary to make the tail of the swan. Its length is approximately 25 cm from the base. Having made such a length, the further process of eversion of the tire will be easier.
The protruding metal cord from the sections must be rubbed with a grinder or sandpaper so they don't hurt your hands.
Now the product from the tire must be turned inside out.
Along the length of the neck, in increments of 15 cm, it is necessary to drill double holes for the staples, with which the rod will be fixed from the base of the neck to the head.
We make staples about 10 cm long from pieces of wire and insert them into the drilled holes.
Next, he takes a thick wire or a rod and fastens it along the swan's neck using pre-prepared staples. A small piece of wire, about 10 cm, should remain free from the base of the neck. Then we bend the neck of the swan in the right way.
Next comes the painting of the swan in the selected color. To do this, you can use any paint that is resistant to atmospheric phenomena.
For a stable location of the swan, it is necessary to put stones in the base or substitute another tire. Also at the base of the swan, you can organize a flower bed.

How to paint a swan from a tire?

You can use additional decorative elements, for example, a crown, which you can independently build from plastic bottle, the base of which will be the neck. Paint the crown in gold, fix the base on the head of the figure - and then the magical bird Tsarevna - the swan - will settle in your garden. If another tire serves as the base for the figure, it can be painted in a contrasting color, such as blue, as if a swan is floating on water, or green. If you do not want to be like most gardeners who have white swans in the garden, then the swan can be painted black, it will look very impressive.

When several swan figures are made in the garden, black and white swans together will look very original.

In this case, it all depends on the personal preferences of the person and his imagination.

Video

You can decorate the site not expensively and effectively by making beautiful swans. Instructions for cutting swans from tires from cars in the video: