Ironing clothes can not be called an exciting activity. Of course, today you don’t have to pour hot coals into a cast-iron iron, but try even the most modern device steam the creases on a linen skirt! This jewelry operation is best done using a device such as ironing board with your own hands.
Everyone knows how much easier any task is well organized workplace. But prices for good board for ironing start from one and a half thousand rubles and go to infinity. handy thing, no one argues, but the money is still a pity. Especially when you see that the design is nothing complicated, and it is quite possible to do it yourself.
Preparatory stage
ironing board requirements
- A quality product should be light, but durable. But if such a result cannot be achieved, it is better to sacrifice lightness than strength. If the board staggers on thin legs, bends and cracks under the weight of the iron, then it is better to continue ironing on the kitchen table.
- The plane of the board itself should be sufficient in area. Otherwise, it will take more time to roll up and pull up the linen than to iron it.
- If the board is upholstered incorrectly, it is necessary to lay an additional blanket or thick material on it. To avoid unnecessary worries, the plane is fitted thick cloth with soft lining.
Tools for the job
- Electric jigsaw.
- Manual milling machine.
- Drill, cork drill ∅ 25 mm, drill ∅ 8 mm.
- Drill stand.
- stapler.
The choice of material for work
A thrifty master does not run after every plank in building supplies. Near the wall in the garage, he will always find the remains of timber and furniture panels. And we don't need anything else. We stop our choice on a shield 18 mm thick and a planed beam for legs. Plywood is not suitable - under the influence of steam and water, this multilayer plate will very soon be bent by a propeller.
Product detail:
- Ironing board dimensions 18x1220x300 mm.
- Bars 35x40x1100 mm - 3 pcs.
- Bars 35x40x300 mm - 2 pcs.
From fasteners, screws, M10 bolts will be needed. For the upholstery of the board, it is necessary to prepare a piece of fabric and a strip of foam rubber. Foam rubber can be replaced with a covering geotextile fabric Armoteks, folded four times. It is better to use a special fabric - non-stick, waterproof. But thick cotton is fine too.
Cutting lumber and assembling an ironing board
Transferring the dimensions of the board to the fragment furniture board. We cut the workpiece using an electric jigsaw. Solving the problem of how to make an ironing board convenient for work with your own hands, we cut out one side of the cover in a semicircle with the same tool. We round the edges of both sides of the workpiece with a milling cutter.
We round the edges of all five bars with a fillet cutter with a small diameter. We mark holes on long bars: we retreat 580 mm from one edge of the 1100-mm workpiece, and 520 from the other. At the marked point, we drill nests ∅ 8 mm.
We make selections in two long bars with a cork drill. Thanks to this, the heads of the M10 bolts will be recessed into the wood. We insert a bolt with a washer into the socket. Turn the middle support bar 180 degrees.
We drill through holes for bolts in small blanks, stepping back from the edge of the bar 30 mm. From one end we select sockets for bolts.
We retreat from the edges by 20 mm, make through holes with a drill ∅ 8 mm. We select the recesses for the bolts in the legs.
Listening to the advice of the masters on how to make an ironing board, we round the upper ends of the legs with a cutter and twist them with small blanks using bolts.
We retreat from the straight side of the board 180 mm. For fidelity, you can draw an axial line along the board. We lay the resulting subassembly along the centerline and fasten it with screws to the cover. We screw the supports to the transverse legs, which at the same time act as stiffeners for the folding structure.
We mark a recess on the board for fixing the middle leg. The height of the product depends on the location of this stop. If this indicator is not so important, we make the angle between the legs 90 degrees. The nest is selected by a milling machine.
We saw out a lock on the middle leg for secure fastening to the lid.
We check the horizontal of the unfolded board. If there are any irregularities, adjust the height of the legs. The height of the finished structure should be 740-780 mm.
Ironing board upholstery
We cut out a strip with dimensions of 400x1500 mm from a dense material. If geotextile is taken for the substrate, we fold it four times and lay it on the board. From above we cover with a cloth and iron it (armotex cannot be ironed directly). We turn the board over and shoot the material around the perimeter with a stapler. We cut off the excess.
The ironing board is ready. This simple design will make life much easier for the hostess. Say what you like, but you have to iron the little things almost every day - now trousers, then a shirt, then a handkerchief. Now such operations will take place quickly, cheerfully, without maxims about the current muzhiks' shorthandedness. These are the miracles available home master!
!
Hi all!
In this article, we will consider an easy way to convert an ordinary ironing board into a folding one.
Probably everyone has such a thing as an ironing board, so I have it! But, unfortunately, there is no place in the apartment for her at all. When unfolded, it takes up precious space and interferes with movement around the apartment; when folded, there is also nowhere to put it, so after thinking a little, I decided that it was time to attach it somewhere. The only free place in the apartment was the loggia, the size of the board fit perfectly, and besides, there were sockets in this place, which undoubtedly simplified everything. It only remained to think of a way to adapt the board so that it was convenient to use. What I got out of this, you can find out by reading the article to the end.
I enclose detailed instructions, and photo report.
Materials and tools
To convert a regular ironing board into a folding one, we need the following:Material
- 2 door hinges;
- heck of medium size.
Tool
- screwdriver;
- roulette;
- pencil.
Manufacturing process
Let's get started!
Here's an ordinary ironing board.
Next, take it, turn it over and put it on the floor.
Now we unscrew all the existing fasteners.
Next, we take the unscrewed rack and move it forward to the narrow part, previously the mount was on the opposite side. We place it so that the stand evenly fits along the length of the board, then, when everything is ready, we fix it with self-tapping screws. The front will serve as a support.
Now it remains to fix the supporting part, which sets the height of the board.
Before starting the rework, I measured the step support legs by selecting optimal height, since in the future it will be only one, the other two will not be involved, but they, by the way, are not actually needed.
Then we fix the stop in the right place.
It turned out the following.
Now it's time to transfer the converted structure to the loggia.
In order for the ironing board to be able to recline, I took two hinges that I have, due to them the back of the board will receive support and the ability to recline.
Placed them on right level, made markings for the holes.
Drilled holes. Attached with dowels and screws.
Then I unscrewed everything, and put a new cover on the board, since the old one was rendered unusable, and fixed everything back.
The next step was to install the locking element, it will hold the board in the folded position.
The most suitable element for this seemed to me to be a heck.
Fixed it at the right height.
Further, the second element from the heck was installed directly on the board itself.
When folded it looks like this.
That's all, the board is ready to use.
Working principle of folding ironing board
The principle of operation is quite simple. In the photo, I think everything will be clear.
So, with the help of simple actions, with a minimum of materials and tools used, we got such a convenient folding ironing board.
This concludes my article!
Thank you all for your attention!
A detailed guide on how to make an ironing board with your own hands will help you find an approach to your spouse in order to always have ironed things.
What should be the ironing board
- Lightweight and durable. If lightness does not provide strength, then sacrifice it for safety. It’s better to pump up muscles by unfolding and folding the board than a burn or injury from the fact that the board fell apart from pressing with an iron.
- The length of the plane on which things are ironed should be such that clothes fit on it. large sizes. Otherwise, you will no longer get tired of the process, but of the constant tucking and turning of the laundry.
- The board must be properly covered. Otherwise, ironing will be inconvenient and you will have to lay something. Therefore, cover the surface with a dense material, under which a soft substrate must be laid.
What tools and materials will you need to make your own ironing board
- Electric jigsaw
- Milling machine
- Drill and drills (cork with a diameter of 2.5 cm and for wood with a diameter of 8 mm)
- stapler
- Furniture board 18 mm thick
- Planed timber (you will make legs out of it)
Do not make an ironing board out of plywood because it will deform under the influence of temperature changes.
- Screws - the more the better
- M10 bolts - in terms of quantity, the same recommendations as for screws
- Foam rubber or geotextile - underlay for upholstery
- Upholstery fabric – must be non-stick and water resistant.
If you can't find one, cotton will do.
How to make an ironing board with your own hands
- First determine the dimensions. For our example, we chose the following:
- ironing surface - 122x30 cm
- 3 bars measuring 3.5x4x110 cm
- 2 bars measuring 3.5x4x30 cm
You choose your size, focusing on the height and storage of the ironing board.
If you make a mistake with the size, then cut off the excess.
And here's what should happen in the end.
The ironing board is a very handy accessory that facilitates the process of caring for garments. However, its storage is quite problematic. A do-it-yourself ironing board made from improvised materials can be built-in or foldable, which greatly facilitates its use.
Such a product can be independently built into a wall or partition. At the same time, it can be disguised as a common interior, and when folded, the board will not be noticeable. In order to build such a structure, you will need a grinder with a cutting ring, a drill, a wood saw, and a vacuum cleaner (for garbage collection). do it yourself is quite simple. It is necessary to take a piece of thick plywood and cut out an element of the required shape from it. It cuts a hole in the wall.
In order for the board to be put up and used, you will need a wooden support bar. The element will be attached to the wall with hinges. Such an ironing board with your own hands is cut out very quickly. The depth of the niche for the product should be about 10 cm. The height and width of the niche should exactly repeat the dimensions of the board. After the hole is ready, it should be carefully processed sandpaper and primer mix. In principle, in order to "cultivate" the opening, you can use drywall.
The ironing board, made by hand, has simple design, so even a non-specialist can cope with the work. When attaching the product, you should also consider at what height you will use it. Try to mount the board in a way that is comfortable for you. After the main canvas is screwed, you should fix the support on which the board will be installed in the operating mode.
A do-it-yourself folding ironing board is built according to the same scheme. If you want to homemade design unfolded, then it must be cut in the middle and twisted with loops. In this case, the board will take significantly less space and will be fairly easy to use.
To fully prepare the structure for work, you should cut out a piece of foam rubber, the size of which will correspond to the dimensions of the canvas. Next, we attach it to plywood and fit it with a fabric cover. Wrong side boards can be pasted over with the same wallpaper that decorates the walls of the room.
Please note that the board must be fixed to the wall with a special fixture. Otherwise, it may recline on its own. Such a situation cannot be allowed. During operation, all wooden details antiseptic, which will significantly increase the life of the tree.
In principle, a do-it-yourself ironing board made in compliance with all the rules can serve you for a long time and will cost much less than a store product. These are all the features of the structure of the presented design. Choose to work only quality materials. Good luck!
Do-it-yourself ironing board
Does your wife complain about the ironing board, which is narrow and short, and therefore it is inconvenient to iron large items, sheets, duvet covers, curtains and curtains? Whatever you do for peace in the family!
To make an ironing board, we need:
A piece of chipboard 1400 x 11 50 mm (if there are no panels of the disassembled cabinet left)
Piece of piano loop 680 mm
Screws 3 mm x 30 mm (6 pcs.)
Screws 3 mm x 14 mm (25 pcs.)
Hacksaw for metal
Screwdriver
- a piece of old flannelette fabric or rug measuring 500 mm x 1500 mm
Upholstery piece 500 mm x 1500 mm
Stapler with staples or hammer and shoe nails
We pick up the tool and take out the panels of the disassembled cabinet. in front of you appearance ironing board and drawing with dimensions. The width of the board is 40 cm and the width of the supporting panels is 34 cm.
Bars 2 under the board are fastened either with screws with a diameter of 3 mm and a length of 30 mm, or with screws and nuts. In this case, it is necessary to make recesses for the heads of screws or screws and for nuts. Elements 1 - piano hinges, for fastening of which self-tapping screws 0.3 mm and 14 mm long are used.
The transverse element 3 prevents the structure from spreading. It can be made from the same material or from an old ski pole. A distance of 3 cm between the ends of the board and the ends of the bars 2 will be quite enough for attaching the upholstery fabric.
When assembled, such an ironing board is only 8 cm thick. If you want to lighten the construction, cut out the areas shown by hatching on the slope panels.
If you don't have a stapler, keep in mind that shoe nails are driven into the end of the board, not from the bottom.
