A do-it-yourself soldering iron stand is a very convenient and practical device that acts as a kind of table and performs a protective function. Before soldering, the soldering iron must be warmed up. When warming up, the case gets very hot, which is why you should use a stand to protect any items.
Design of the soldering iron stand: 1 – base, 2, 4, 5 – contacts from a relay type MKU-48 for 220 V, 3.10 – support posts, 6 – disk, 7 – spring, 8, movable contact rod KP 9 – square , D1 - diode type D7Zh.
The need for a soldering iron stand
A high-quality and practical stand for a soldering iron is needed by all those who deal with soldering. You can make it yourself from scrap materials, you just need to have certain skills and certain tools. A homemade soldering iron stand is quite simple to make and use. In order for a thing to be convenient, it must have certain slots intended for containers with flux and alcohol, boxes for rosin and alcohol, as well as a place for displaying some parts. A homemade soldering iron stand can be used with a tool of any power. When making a structure, it is necessary to arrange all containers in such a way that it is convenient to solder.
Return to contents
How to make a stand for a soldering iron?
Factory options are very inconvenient and small, so many people ask the question: how to make a stand yourself so that it is practical? Manufacturing must begin with the selection of materials. Must have:
- duralumin sheets approximately 1.5 mm thick;
- small wooden plate size 50x40 mm, made of oak or beech;
- two small metal boxes with lids;
- bottles of varnish, preferably identical and with brushes.
When everything is ready, you can start manufacturing. It is necessary to make holes in the duralumin plates for bottles of flux and alcohol so that they can be inserted quite freely. The holes for the jars must be made so that they fit very tightly. After all the holes are ready, you need to bend the base a little so that you can make a support.
If desired, you can make special stands so that the stand is a little higher and you can work more conveniently. All parts must be carefully processed with a file, and then sandpaper so that the edges and all corners can be rounded.
When everything is ready, you can start assembling. The lower support for the containers must be screwed to the upper support and the wooden platform. By using epoxy resin you need to glue the jars and bottles into the base. Alternatively, you can take a small rectangular jar and place it between the stands on which you can place the device. In such a jar it is very convenient to store various devices that are simply necessary during soldering.
You can make a soldering iron stand from a regular tin can. To make it you will need:
a soldering iron stand can be made using a nail or drill in the bottom of the can, making a small hole for the bolt.
- wire hanger;
- washer;
- bolt with nut;
- marker;
- tin.
Wire taken from a hanger is very convenient for making this type of product, because it has good strength, but is also a little springy.
To make it, you must first bite off the wire on both sides with pliers and align it well. You need to support the wire with one hand and wind it onto the marker with the other. You need to make a small eyelet on the resulting spring using pliers.
Make a small hole in the bottom of the can using a drill or nail. After this you need to assemble the entire structure. It is necessary to insert the spring into the prepared tin can and tighten it with a bolt, nut and washer. In this simple way you can make a very convenient and practical soldering iron stand.
Return to contents
How to make a “smart” soldering iron stand?
You can not only make a regular stand for a soldering iron, but also make a “smart” model that will independently regulate the heating level of the device. A smart stand for a soldering iron must be plugged in during operation, and it will regulate the heating level of the device, thereby protecting it from overheating. Thus, there will be no overheating, but will always be ready to work. To make a stand for a soldering iron, you need to take the following materials:
The finished structure is assembled by tightening the spring inserted into the box using a bolt, washer and nut.
- double socket for outdoor installation;
- a piece of single-core wire, preferably copper;
- plywood;
- transformer;
- connector for securing parts on a plane;
- LEDs;
- resistor;
- switch;
- wires;
- pin.
Once all the materials are prepared for work, you can begin the actual assembly. First of all, you need to decide on the size of the base itself and cut it out of durable material.
After this, you need to make a socket, for which you need to drill holes for the socket socket, install LEDs and a switch.
Then install everything in its place and solder the necessary wiring to each other.
From the socket through the switch you need to bring out the wires for subsequent connection of the transformer, then you need to bring out the wires through the socket of the socket and attach a resistor, a red LED, which will signal that the transformer is turned on. All this must be carefully secured to the base. In addition to making a stand, you need to make a holder for the heating device. To make it, you need to fold the wire, preferably copper, in half and attach it to the base. It is worth taking care of special boxes in which rosin and solder will be stored. The boxes should also be screwed to the base.
All exposed wires should be wrapped with insulating tape and we can assume that the stand for the soldering iron is ready. You can get to work and be sure that the heating device will work perfectly, without overheating at all.
Greetings, Samodelkins!
To do this we will need the following tools and materials:
1. Laminate scraps left over after renovation
2. A small piece of 16mm chipboard
3. Clamp for polypropylene pipes
4. Electric jigsaw
5. Wood glue
6. Spray paint. The author used black, but then, in some way, he regretted that he chose such a gloomy color. dark color. Therefore, it is advisable to choose a more cheerful color.
7. Putty
8. Sandpaper
9. USB lamp from a fix-price store
10. 2 alligator clips
11. A pair of small bolts and nuts for them
12. Copper wire
The author begins work on a homemade product. First you need to decide what you are going to store in your homemade product. To determine the size of the future product, he compactly folds what will be stored in a homemade organizer in the near future.
On at this stage he also notes the approximate dimensions of the future product.
Now, but more precisely, he makes a drawing of the workpiece. When making a drawing, it is also necessary to take into account the thickness of the materials used.
Now the author proceeds directly to making the organizer. First, he cuts the laminate and chipboard to size. Super precision is not needed here, but still try to make the cut as close to 90 degrees as possible. This is what the box should look like.
Next, you need to mark what size the stands for the soldering iron holder should be. The recesses should naturally be higher than the walls of the box, and the stands themselves should be of such length that, when lying down, they fit comfortably in the box, and in one layer. Now you need to cut out a recess for both metal parts. The author does it this way:
After some time, he realizes that this could have been done much easier with a wood crown, and only then cut in half. Well, as they say, a good thought comes to someone else or to ourselves, but late.
This is what ended up happening. All you have to do is tighten a couple of screws and you're done.
Now let's start assembling the box itself. Starts from the bottom. Makes small recesses in advance for the screw heads. Then, in the gluing areas, use sandpaper to remove the entire glossy layer of the laminate. Next is gluing. The author takes a special glue for wood products and glues wide side walls, made of chipboard. When gluing, it is advisable to use clamps. After the glue has dried, it is necessary to secure the entire structure from below with self-tapping screws. Next, check the perpendicularity of the walls. You need to measure the angle between the walls. It should be straight - 90°.
Everything is fine, let's move on. Now this design It has rigidity, so it can be glued and screwed onto screws at the same time. This is what happened.
The author made the lid of the box using a tongue-and-groove connection. It's long and tedious. The author adjusted everything by hand so that it fits tightly enough into one whole. Next he glues all the details. This will be quite enough, since practically no loads are expected on this part of the organizer.
Then you will need sandpaper. It is necessary to use it to sand down all possible irregularities and apply wood putty. Putty is mainly needed to cover the chips at the ends of the chipboard, and to hide all sorts of jambs that formed during manufacturing. After the putty has hardened, you need to clean it. The same sandpaper will come to the rescue.
The next stage is painting.
It is necessary to paint the box to give it a marketable appearance.
Well, the paint has completely dried and here the author would like to add one point. It was necessary to select more cheerful color so that loved ones do not have the desire to take the box away and bury, for example, a hamster in it. Anyway.
Now you can carefully remove the tape from the stand where the hot part of the soldering iron will be. We don't need the smell of burnt paint. If there are adhesive traces left from the tape, you can try to remove them. Or leave it as is. After turning on the soldering iron, the remaining adhesive from the tape on the stand should burn out.
And on the part where the handle will be we put on the original rubber band from the fastener for polypropylene water pipe so that the soldering iron does not slide on the stand.
The mounting of the soldering iron stand itself will be very simple. Nuts are glued into the racks and the whole thing is tightened with bolts with heads to the wall of the box. Here's what we ended up with:
Everything is very simple and practical. If you wish, you can drill several more of the same holes, and if you have more than one soldering iron, then this design feature will be very useful. It will be possible to rearrange the rack under different sizes soldering iron Now the author decided to make a couple of clips in the side wall of the box. They will be used as a third hand for soldering. To make such a design you will need this miracle of Chinese engineering from a fix-price store.
In the store it is positioned as a USB lamp for illuminating a laptop keyboard. It can also be used in conjunction with a power bank, or as a night light. It is better suited as the latter, since, to be honest, its light is so-so, but its flexible leg will be useful to us. You will also need a couple of small screws with mortise nuts.
It is necessary to disassemble this miracle lamp. In principle, he doesn’t mind at all, and he himself falls apart, thereby providing a kind of assistance in disassembling.
When working with a soldering iron, a special stand is required. The soldering iron cannot simply be left on the table or some other surface. As a rule, any suitable item in the house is used in this capacity. With a little effort, you can make a soldering iron stand yourself. Such a device will be cheaper and will be adapted to the needs of the master.
How to make a soldering iron stand with your own hands? To make it, you first need to make a stable base from a material that conducts heat poorly. The following tools and materials are required for work:
From chipboard sheet cut out a rectangular blank, sand the sides with sandpaper, rounding the corners. Next, make four rubber legs, which can be cut from a piece of rubber or a cork from chemical test tubes. The legs are screwed to the base using self-tapping screws.
A hook is bent from a long strip of iron with pliers, which is used to install the heating part of the soldering iron. At one edge of the stand, an iron strip with a hook is secured with bolts. To reliably fix the structural elements, you need to pre-drill holes in the chipboard workpiece.
The holder for the soldering iron handle can be made from any part with a suitable recess . It is bolted to the edge of the music stand. Closer to the heating element, a soldering holder is installed in the same way. To do this, use a metal plate made from old radio components or other consumables.
At the soldering site, you can melt a piece of tin, which is heated during operation. This results in a convenient and versatile device. Rubber feet give the structure stability and prevent damage to the table surface.
The simplest device can be made from thick wire. It is a cone spring that is attached to a stable base. A piece of wire, approximately 30 cm long, is wound onto the tool. There is an eyelet at the end for attaching to the stand. For the spring, you can use a thin clothes hanger.
The base is assembled from any suitable item - a tin can, unnecessary detail from household appliances or a piece of plywood, etc. A hole is first drilled in the workpiece, where a spring is attached using a bolt.
In another version of the design, rectangular holders with recesses for a soldering iron are made from wire using pliers. They are fixed on both sides to a base made of chipboard or a wooden block. The soldering installation can be equipped with containers for tin or rosin, and a box for storing small parts, which is glued with special glue.
Soldering iron stand with magnifying glass. To make it more convenient to work with small parts, a special stand with flexible holder(“third hand”) With its help you can fix various equipment: a magnifying glass, a backlight and other tools. The holder is secured with hinges, which allows you to rotate the device in different directions. All parts of the holder are made of metal elements to ensure the stability of the structure.
To work you will need a cover from computer unit power supply and the following tools:
- metal scissors;
- ruler or caliper;
- file or sandpaper;
- marker.
Mark with a marker approximate dimensions blanks for parts from a computer (width 60 mm, height 35 mm). A stand is cut out according to the marks made, then recesses are made on the sides where the tool is installed. For safe work The sharp edges of the product are treated with a file or sandpaper. Thus, a homemade stand for a soldering iron can be made in 15 minutes.
A computer's power supply can become a mobile device. Such a device is a box or case, inside of which there are compartments for soldering, rosin, a clamp for circuits and other small parts. The wire holder is attached to the outside and easily folds over the lid of the pencil case.
The product is easy to manufacture and does not require special materials. For holders, fuse jaws are used, which are attached to a base made of a wooden block or PCB. The distance between the holders is set in accordance with the size of the soldering tool. The fuses are screwed using self-tapping screws into pre-drilled holes.
If you urgently need a soldering iron, you can quickly make a stand from screws or nails. IN wooden base nails are driven in crosswise. This design is quite stable and holds the tool well.
To make a homemade soldering iron stand, you do not need any special knowledge or skills. For work, scrap materials that can be found in any home are often used. DIY devices are simple and easy to use.
A soldering iron stand is an indispensable attribute of a soldering installation. It can be purchased at any hardware store or on the market. However, its cost is quite high. To save your own money, a stand is made for financial issue, its functionality is considered. That is, it can be used for various needs on the farm or in a production workshop. There are quite a lot of manufacturing options. All of them differ in the complexity of the design and the amount of time spent.
General information
As mentioned earlier, a do-it-yourself soldering iron stand - convenient device, which performs many functions. First of all, it is a protective surface, which prevents damage to property.
Before working with the soldering machine, it must be warmed up. In this case, the metal case heats up to high temperatures.
Soldering iron stand - what is it for?
A high-quality part is necessary for those people who do a lot of work with soldering. To make such a device as a soldering iron stand, no special skills or abilities are required. The process uses simple and available materials and tools. Finished device easy to use. A homemade soldering iron stand should consist of individual elements. First of all, special containers are provided for rosin, flux and a department for mixing them. Some models are equipped with a box where they are stored small parts. The soldering iron stand is suitable for any device, regardless of its power and degree of heating. When making the structure, the location of these containers should be taken into account. Everything should be located so that it is convenient for the master to solder.
How to make a soldering iron stand?
It is not profitable to buy ready-made stands, since they are expensive and small. dimensions, which are not suitable for all types of devices. Therefore, many users ask this question: “How to make a soldering iron stand with your own hands?”
Before starting production, you need to prepare the materials. To do this, you should purchase the following components:
- duralumin sheets, the thickness of which is 1.5-2 mm;
- small wooden beam ok (you can use different kinds tree);
- varnish containers;
- two metal boxes.
Once all these parts have been purchased, you can begin making the stand.
So, several holes need to be made in the plate. Containers for rosin and alcohol will be attached to them. Installation of cans is easy. The containers should be easily inserted into the structure and fit snugly against each other. After these procedures, it is necessary to make a support. It is made by bending the base.
If necessary, each person can make special racks that lift the structure a certain distance. This is done for convenience during the work process. Preparatory work ends with processing the duralumin sheet with a file or sandpaper. Corners should not have sharp ends.
Assembly of the structure
So, let's start assembling the soldering iron stand. The prepared support must be secured to a wooden beam.
This can be done using screws. Next, the prepared small containers are attached. They are attached to the base using special glue or epoxy resin. Many craftsmen also install a small container between the racks. You can store small parts in it that you will need during your work.
From wire
A stand for a soldering iron made of wire has gained great popularity among many craftsmen and hobbyists. It can be made from an ordinary tin can. In the process of assembling the installation, simple parts are used:
- tin;
- pencil large diameter;
- washers and bolts;
- wire.
First you need to make a spring. The first thing you need to do is purchase wire from the store. Some people remove it from other indoor fixtures. It must be thick enough so that a soldering iron heated to high temperatures does not destroy it. In addition, only high-strength material will be used. Ready product should spring back.
Cut the required length of wire and carefully align it. To create a spring, use a large diameter pencil. Holding the wire, carefully wind it onto the pencil. The result should be a tight spiral. At its end is done special mount in the form of an ear. For these purposes, pliers are used.
The next step is to prepare the tin can. A small hole is drilled in its bottom.
This can be done using a nail or drill. Next, the stand for the soldering iron is assembled. The prepared spring is inserted into the jar and the structure is secured using a bolt and nut. To ensure a more durable fastening, washers are used. This method is quite simple. Anyone can make a soldering iron stand. Its manufacture does not require much time or special tools.
Soldering iron stand with power regulator
All more people prefer to use this particular type of stand. Its essence lies in the fact that it is equipped special device, which independently adjusts the degree of heating of the soldering iron. Therefore, the device does not overheat and does not fail. The stand differs from other types in that it requires an electrical connection to function. To make a version with a power regulator, you need to take the following elements:
- copper wire;
- a small piece of plywood;
- transformer;
- LEDs;
- fastening parts;
- resistor;
- wires;
- socket for connecting to the network.
After everything necessary details were purchased, proceed directly to assembling the stand.
First, select the size of the installation. Based on this information, a base is cut out of a sheet of plywood. Next, the transformer and other parts will be attached to it.
Fuse stand
Manufacturing this option does not take much time, effort, and also does not require large financial investments. The base is a wooden beam onto which the fuse jaws are attached. They can be of various sizes. It all depends on the personal preferences of the masters.
Benefits of stands
First of all, the main advantage is mobility. Homemade coasters used by people who quite often do soldering, working within several workshops. Such a design is not always at hand. However, it is easy to make. In addition, there is no need to carry rosin and tin separately in different containers, since now they are stored in special jars on a stand. That's why homemade installations They are popular not only among amateurs, but also among professionals.
How to make a simple model?
It happens that you urgently need to use a soldering iron, but there is no stand for it.
In this case, there is no time to look for the necessary parts and run around the shops. Therefore, it is better to make a simple one, but also reliable design. There are many options, but there is the fastest one. The stand can be made in a few minutes. The base will be the usual wooden block, and stands - screws or nails. They are driven crosswise into the beam. This creates a stand on which the soldering iron fits well and holds tightly.
Conclusion
When soldering elements, there must be a stand for the device. This auxiliary equipment is expensive, so it is better to make it yourself. This process will not take much time, effort, and will also save money.
