The lawn mower patriot won't start. Gas trimmer won't start. What to do? Why won't the lawnmower start

The tool, despite its small dimensions, is a complex technical device. If you study the instruction manual, it turns out that the reasons why the lawn mower does not start are known and can be eliminated. It is necessary to consistently eliminate factors that make it difficult to start the tool. Usually start with more accessible nodes with easy health checks.

All the reasons why the lawn mower does not start can be classified according to the specifics of the operation of individual nodes. In the service center, malfunctions are classified:

engine malfunction (piston wear, bearing failure, crankcase crack);
fuel mixture supply malfunction - clogged pores air filter or malfunction of the carburetor;
the ignition system does not work;
mechanical failure - leaking hoses, broken wires under the braid, rupture of tubes.

The user first needs to check if there is fuel in the tank. Start in accordance with the instructions, putting the saw on its side. Set the air damper to the “closed” position, pump up fuel, turn on the ignition and make 3-4 sharp jerks with the starter. If the engine is running, open the air damper. The lawn mower does not start - we repeat the operations with a slightly open air damper.

Motokosa cannot work for a long time. The gearbox and motor will overheat. You can mow for no more than 15 = 20 minutes, taking a five-minute break. On a hot afternoon, the opening time is halved. When mowing weeds, sedges, work time needs to be reduced.

If the launch fails, we begin to look for the cause of the failure:

check fuel quality;
make sure that the candle is working and the candle channel is clean;
check the cleanliness of the air filter;
make sure the fuel filter is not clogged;
check the cleanliness of the breather;
clean the outlet.

More complex causes will be malfunctions detected during diagnostics, leading to overhaul carburetor. Such reasons include clogging of the internal channels of the carburetor, wear of the gasket on it, and violation of the tightness of the internal halls with loss of vacuum. Repairing a lawn mower with your own hands, if it does not start, will require patience.

The fuel mixture must be prepared with exact observance of the proportions of gasoline and oil. In this case, you can not use a different brand of fuel. To prevent dirt from getting in, gasoline should settle in a glass or metal utensils 2 days. Cannot be used to store fuel plastic utensils. The oil is accurately measured with a medical syringe without a needle. Use only freshly prepared mixture, do not leave unused fuel in the tank. If the engine is naughty, the lawn mower stalls, when you press the gas, the fuel may be to blame.

The lawn mower does not start hot - press the gas trigger and pull the cord sharply several times until the engine starts, then lower the trigger. Won't start - special repair required.

Checking the ignition system, if it does not start, is carried out sequentially:

clean the removed candle from soot and dirt, dry it, set a gap of 1 mm;
connect to a high-voltage wire and check for a spark by pulling the starter several times;
if there is no spark, check the integrity of the high-voltage wire;
replace the candle;
dry the candle channel;
at the same time, the operation of the ignition coil is checked, it is faulty if the working candle does not spark.

It is in the event of a malfunction of the ignition coil that the lawn mower does not start hot, stalls, and works intermittently.

Cleaning or replacing the air and fuel filter will provide required flow ingredients entering the carburetor. The air filter can be washed in soapy water or replaced. If a nylon fabric is used, it is washed, the porous felt filler is replaced. The fuel filter is changed carefully, without leaving the suction pipe open. Whether the air filter needs to be replaced can be determined if the engine starts with the air cleaner removed. Whether it is necessary to change the grid on the fuel supply, if the lawn mower does not start, a dry candle will tell.

Breather, a hole for air inlet into the gas tank. If it becomes clogged, a vacuum is created in the tank and the mixture does not enter the carburetor. The hole can be blown with air or cleaned with a needle. Clean the exhaust channel, remove the muffler anti-spark grid.

Carburetor adjustment and tuning

The maximum and minimum engine speeds, smooth idling are regulated by a carburetor. The stable operation of the lawn mower depends on the amount of the supplied combustible mixture and air, their ratio. The lawn mower will not start if the carburetor is out of adjustment. The procedure for setting the fuel delivery device for low speed (L), high speed (H) and idle move(T) is regulated by the screws of the same name:

The chainsaw should work for at least 10 minutes, as the adjustment is carried out hot.
Screw H is turned smoothly to maximum speed, then turned ¼, counterclockwise, reducing the speed of rotation of the motor shaft.
Idle speed is adjusted with screw T, ensuring that the braid does not rotate.
Screw L is adjusted by first opening the throttle as much as possible, and then gradually reducing the speed to a stable minimum.

After adjustment, a serviceable one with cleaned filters, a checked ignition should ensure the operation of the engine. In the event of a carburetor malfunction, after repairing it, it will be necessary to adjust the supply system again before starting the lawn mower.

Rare breakdowns that prevent the operation of lawn mowers can be:

failure of the rewind spring;
broken or stuck starter pulley;
defective starter assembly.

The most important malfunction, the elimination of which is associated with the replacement of the engine, may be the failure of the engine piston group. The cost of repairs will cost approximately 70% of the cost of the product. To understand the reasons why the lawn mower does not start, the video will help:

Proper care of your chainsaw

There are no unnecessary phrases in the instruction manual, everything that is offered is aimed at trouble-free operation of the lawn mower. Cleaning of all parts after each cycle of work helps to easily remove uncured residues and dirt. Only cooled nodes need to be cleaned. This technique contributes to the quality of air cooling of the engine and gearbox.

For refueling, it is necessary to use fuel with the oil recommended in the instructions. If combustible mixture leave it in the fuel tank, the oil will float up and land on the damper at start-up, worsening its adjustment. The mixture can precipitate and clog the fuel supply in the carburetor.

When storing equipment for the winter, carry out an audit, lubricate the gearbox and piston system, Wrap the entire saw in oiled rags and store in a dry place.

It is impossible, dangerous for the tool and the health of the mower, to use a metal cable instead of fishing line. It cuts more efficiently, but the load on the gearbox and engine increases. A worn piece of wire flies at the speed of a bullet when it is torn off. Efficient mowing can lead to rapid wear of the engine piston group. For greater efficiency when mowing, it is suggested to use the “asterisk” line profile.

Diagnosis of lawn mowers and elimination of causes - video

Petrol trimmer does not start? Prerequisites and solutions on the example of Elitech T750

In general, a similar conversation should begin with the fact that after buying a garden gas tool, it would be better to first familiarize yourself with the annotation attached to it. Gas trimmer filter or buy a new one. Trimmer won't start. Then many troubles could have been avoided. But since it happened petrol trimmer Not start up, then you need to find the sources of inoperability. And in this article we will consider the main prerequisites why trimmer does not start on the example of the Elitech T750 model, and we will also tell general tips for the operation of such a tool.

Let's start with the obvious! Let's figure out how to start petrol trimmer. It may be that the reason lies precisely here.

First you need to bring the red toggle switch on the trimmer bar to the “I” position. This means power on. Then you need to switch the fuel supply lever on the carburetor and use the fuel “suction” button (looks like a pipette, located on the carburetor). If the engine does not start at all or stalls quickly, do not trim and revs. This is necessary to supply gasoline to the engine. Return the fuel supply lever to its original position. Finally, pull the starter handle sharply towards you. Trimmer should earn. Try a few times if it doesn't work the first time. If after such manipulations the situation has not changed and gasoline starts trimmer, then you should first inspect it yourself before taking it to a service center. There are two main reasons why a garden trimmer won't start:

Why a Chinese lawn mower or chainsaw does not start. Practice

Practical tips for troubleshooting. From personal experience.

Not start up on a cold trimmer - eliminate the cause

Trimmer won't start to cold. Cause- air suction, which prevents fuel from being pumped. The petrol trimmer does not start, however, it does not start, cadet cc 98 b video ... trimmer. Into the camera.

Violation of the supply chain.
No fuel.

The second reason why a garden tool does not work is that the fuel has run out. On the Elinech T750, the fuel tank is located near the motor, but on most trimmers it is also located there. We unscrew the cap from the tank and fill it with gasoline (the most best option AI-92, it is inexpensive and does not clog the carburetor like AI-76). Do not forget to add special oil for engines to the tank, 50 grams per gas tank is enough, without it the engine will start to “sneeze” and quickly become unusable. After we close the tank with a cap, wipe the surface of the trimmer and our hands with a dry cloth. Hitachi trimmer won't start. Repair tool, despite its small size. We also do the above manipulations to turn on the garden tool.

To the owner suburban area you can not do without a lawn mower or trimmer. But during its operation, situations may arise when this unit for some reason stops starting. And there can be many reasons for this. Let's find out why the gas trimmer does not start.

Why the trimmer does not start - reasons

To determine why the gasoline trimmer does not start well or constantly stalls, it is necessary to sequentially check the operation of all the main components of the unit. It is especially important to do this after long-term storage lawn mowers. So, the main reasons for this behavior of the trimmer are as follows:

The culprit for the fact that the lawn mower does not start may be a poor-quality oil-gasoline fuel mixture. It must be prepared strictly according to the instructions. Saving here is not at all appropriate, since it can lead to failure of the entire trimmer piston group. You should not prepare too much fuel mixture, as excess gasoline will lose its quality over time.
You should be aware that gasoline trimmers from brands such as Stihl, Husgvarna and some others will not start if cheap gasoline with a low octane rating is poured into them. Therefore, for such units it is necessary to use only high-quality high-octane fuel.
If the trimmer stalls immediately upon start-up, then it may have a flooded candle. In this case, it is necessary to unscrew it and dry it thoroughly for half an hour. Then drain the excess fuel that is in the chamber, clean the candle from soot, put it in place and try to start the lawn mower.
If your new gas trimmer won't start, the cause may be a lack of spark. And this happens because the nest where the candle is located is dry and the fuel does not light up. It should be slightly moistened with a few drops of gasoline threaded connection candles.
The petrol trimmer may stall due to clogged air or fuel filters. It is best to replace such elements with new ones.
The exhaust port and breather can also become clogged. After cleaning these trimmer elements, it will be possible to start the unit without any problems.
Another reason why a gasoline trimmer will not start, even when there is a spark, may be a clogged carburetor. To clean the channels and jets, it is necessary to blow them with compressed air using a compressor.
Wet chainsaw candle: why and what to do

You can use it to clean the carburetor and special flushing.
If the carburetor gaskets are worn out, you need to change them. And if the tightness of this device is violated, it will be necessary to determine the faulty part of the carburetor and replace it.
The trimmer may not start due to wear of the piston group. However, it is better to change such parts of lawn mowers in a service center.

Trimmer line - which one to choose?

Immediately after buying a grass trimmer, we are faced with a lot of questions - how to use it correctly, how to refuel (if we are talking about a gasoline tool) and, of course, which fishing line is best to choose. Look for the answer to the last question in the article.

How to quickly remove a stump without uprooting?

Many gardeners sooner or later face the need to cut down trees growing on the site. After that, stumps remain, and if the trees were of considerable size, it is very problematic to uproot them. The article talks about alternative ways getting rid of stumps.

Processing currants in the fall from pests and diseases

Almost every summer resident grows currants, which are loved because of their palatability And useful properties. It requires proper care, which also includes the treatment of plants from pests and diseases. The features of these autumn events are described in the article.

How to choose a petrol grass trimmer?

A beautifully manicured lawn is an adornment of any site. And a regular haircut helps to maintain its attractiveness. In this case, you can not do without a lawn mower or trimmer. In the article we will talk about the intricacies of choosing a gasoline trimmer.

What should I do if a chainsaw spark plug is flooded?

Most often, this happens to beginners when, at the first start, they skip a “pop” on a closed air damper and continue to pull the starter handle, respectively, there is a lot of gasoline in the combustion chamber, and not enough air prevents gasoline from igniting.

The problem is solved simply:

We unscrew the candle with a candle key and check its condition. If the candle is wet and there is a spark, then it was flooded. We open the air damper, turn on the switch button, squeeze the gas “to the stop” and start it. Excess gasoline should come out of the exhaust saw and the saw will start.
We unscrew the candle with a candle key and check its condition. If the candle is wet and there is a spark, then it was flooded. Turn the chainsaw upside down and turn the starter about ten times, while excess fuel will flow out of the engine cylinder. Then wipe dry (bake) the spark plug, or replace it with a new one and try to start the engine again exactly following the operating instructions. If the spark plug is completely dry, it means that the engine is not getting fuel. And since it is in the tank, the problem is probably in the carburetor. You can draw a little mixture into the syringe, inject it into the cylinder, tighten the candle and try to start the engine. But if the engine starts and immediately stalls, then the problem remains and you need to contact the service center.

You have no rights to post comments

Gasoline trimmer does not start - reasons

Many gardening Tools useful and effective, but there are times when the technique refuses to work. Among them was a trimmer that can mow both a miniature lawn and huge lawns.

Reasons why the gas trimmer does not start

There are different reasons why the gas trimmer does not start:

The most common reason for a breakdown lies in the wrong choice of fuel. Often, overly economical users of the device pour something dubious into the tank, but not fuel with a normal octane rating. Low-quality fuel, which was kept in plastic canister long time, has a terrifying effect. The device, which has lost its functionality for this reason, is sent for a complete overhaul of the mechanism.
How not to get confused if the lawn mower does not start
There is another common situation when a gasoline trimmer starts and stalls. The problem could be the spark plug or air filter. In the first case, after inspection, it will be found that the candle is “thrown”. This happens even if it has recently been wiped and dried. If everything is in order with the candle, then it is worth inspecting the air filter. More often than not, it gets dirty and needs to be replaced. If the device continues to refuse to start, then the problem lies either in a faulty ignition coil or in a clogged muffler.
The device can deteriorate not only due to low-quality fuel, but also due to improper handling. For example, the fuel is checked, there is a spark, but the device does not start. The cause may be a spark plug filled with gasoline. To correct the situation, you just need to unscrew the candle, wipe it, dry it and check for performance.
Sometimes such a situation develops - the gasoline trimmer does not start when the candle is dry. Then it is necessary to lubricate the threaded connection with gasoline. It should be slightly damp, otherwise there will be nothing to catch fire.
Often, the owners of the device find themselves in a situation where the gasoline trimmer does not start well when hot. Some masters claim that the problem lies in the ignition coil. Therefore, it must be changed, and the device will work. But the problem may also be in the engine overheating, especially if a reinforced knife of the type circular saw. To avoid such situations, you should carefully study the instructions, which specifically describe what types of discs can be installed.

The reasons when a new gas trimmer does not start can be the most commonplace, for example, the inability to use the device. If the user stores it correctly, uses high-quality fuel and does not leave gasoline in the trimmer, then the unit will serve faithfully for a long time.

Caring for personal plot, summer residents periodically encounter the fact that the lawn mower does not start. There are many reasons for tool failure. To correctly diagnose the problem, the owner of a unit useful in the country needs to know the device and the principle of operation of its individual parts.

Since the gas trimmer is a complex device, you must carefully study the instruction manual before starting work. Very often it is simply ignored, or gets acquainted with it superficially. As a result, when the tool stalls or refuses to start, the question arises - “Why doesn’t the lawn mower start?” A long seasonal break in work, improper storage and untimely maintenance of the trimmer will cause a lot of trouble for the summer resident to eliminate the causes.

Where to start diagnosing motokosa

If the lawn mower does not start or immediately stalls after starting, it is necessary to check all the main components and assemblies in sequence. The verification algorithm is as follows:

Fuel tank (fuel quality);
Candle and candle channel;
Air filter;
Fuel filter;
Breather;
outlet channel.

These nodes are most often the source of the main problems, which can be eliminated after a thorough inspection.

Checking the fuel mixture

Before starting the gasoline scythe engine, check the presence and quality of the fuel mixture. Do not save, do not be greedy and "do not be clever" in this matter. Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil-fuel mixture strictly according to the instructions. Calculate its quantity from real needs. Excess gasoline left after work loses its quality over time.

We carry out diagnostics of a candle and a candle channel

If the quality of the fuel mixture is beyond doubt, and the lawn mower stalls at start-up, then a flooded candle may be the cause. Here, an ordinary candle key (every motorist probably has one) and a spare candle are suitable for repair.

We unscrew the candle and wipe it;
Dry it thoroughly (do not ignite);
Excess fuel in the chamber is drained through the candle hole and dried;
We clean the old candle from soot with the help of a file or lady's file;
We set the gap with a distance of 1 mm (you can check with any coin);
We return everything to its place and try to start the trimmer.

It takes at least 30-40 minutes to dry the canal. Otherwise, there is a risk of re-filling a new candle.

If the candle is working, the socket where it is located is completely dry, and the lawn mower does not want to start, we lubricate the threaded connection with gasoline. It should be slightly moist. No matter how wonderful a spark a candle gives out, there is simply nothing to light up in a dry chamber.

If the trimmer engine still does not start, such a reason as the absence of a spark due to poor contact between the candles and the high-voltage wire should be excluded. If the connection is of high quality, but there is still no spark, most likely your ignition unit has “flew”. Here it will not be possible to do without a master, because the part is not repaired, but is sold as a whole assembly.

Diagnostics of filters of lawn mowers

Another reason why a gasoline spit stalls can be an air filter. To eliminate it, try removing the filter and starting the trimmer without it. If possible, then you will have to change the air filter to a new one, or at least blow and thoroughly clean the old one.

The gasoline trimmer may not start due to contamination of the fuel filter. This is the next step in our algorithm. Here we check the condition of the filter element and, if necessary, change it with a new one. When replacing, try not to leave the suction pipe completely without a filter, this is prohibited by any instruction manual. The rush can result in the repair of the engine piston group.

Breather and outlet

Often, “gentle” branded models of lawn mowers do not start and stall due to contamination of the breather. The main function of this element is to equalize the pressure in the gas tank. When this assembly is clogged, a vacuum is created in the tank, preventing the supply of fuel. You can fix the problem by cleaning the breather. You can use a regular needle for cleaning.

The normal operation of the spit with internal combustion engines may be impaired due to the ingress of dirt into the exhaust channel or clogging of the muffler screen. There is such a problem on older models. The issue can be resolved by traditional cleaning and removal of the anti-spark grid.

More complex causes of lawn mowing failure

If the step-by-step troubleshooting algorithm did not work, and your scythe still does not start or stalls, it is worth inspecting the carburetor and the engine itself. A clogged carburetor can be one of the reasons for the unstable operation of the tool. There are three main problems here:

Clogged channels or jets. All this is cleaned with special flushes or blown with a powerful jet of compressed air from the compressor. Do not use needles and wire, as the flow sections may be damaged;
Worn carburetor gasket. Exit - replacement of a failed gasket;
Violation of tightness. To check this indicator, you can use an ordinary household tonometer, replacing the pressure gauge on it with a suitable one. Follow the readings: if they do not change, everything is fine, but if the pressure starts to drop, then some part of the carburetor is faulty. We'll have to find it and replace it with a new one.

If everything is in order with the carburetor, then the gasoline trimmer may not start due to wear on the piston group. If chips, scratches or scuffs are found on the piston or cylinder, they should be replaced. Piston rings are subject to mandatory inspection. A small backlash of the piston when the connecting rod is rocking indicates that it is time to change the rings. This procedure is best entrusted to the specialists of the service center.

Rules for the operation and storage of lawn mowers

In order for the lawn mower to start well in the future, you need to provide it with good conditions storage and operation:

during operation, carefully monitor the cooling system, carefully and timely clean the channels in the housing, as well as the starter fins;
if necessary, use solvents, kerosene and other detergents for cleaning;
do not clean the tool "hot" - let it cool down;
strictly follow the requirements of the instructions regarding the mode of operation, otherwise you may overheat the engine;
if you do not plan to use the lawn mower in the next month, the fuel mixture must be drained from it, because over time it breaks up into heavy fractions that will definitely clog the carburetor channels;
after draining the fuel, let the trimmer idle until it stalls, this will help to completely remove the remaining mixture.

Before winter storage do the following steps:

completely disassemble the braid, rinse and clean all the parts that you can;
inspect the parts for damage, if necessary, eliminate distortions, gusts, bends and any other malfunctions;
pour enough oil into the gearbox and clean the air filter;
you can partially disassemble the motor, rinse, blow and lubricate all moving parts;
in order to lubricate the piston, you need to unscrew the candle, raise the piston to the extreme dead center with the starter, pour a little oil into the candle hole and turn the crankshaft a couple of times;
if you store the lawn mower outside the house, wrap the engine with oiled rags.

Remember, careful observance of the rules will allow you to forget that it is bad to start a lawn mower for several seasons.

Because he worked his way. Why, there can be any number of answers to this question. Bad fuel is far from an argument. Maybe a person does not know how to use it, so it does not start correctly. Fuel is not supplied, the spark plug is broken, the wires are broken, it hasn’t been turned on, it doesn’t know how to use it, the trimmer is burnt out / broken, but you never know what other reasons there may be. There is also such a hand-hooks.

The reasons why gas trimmer won't start, maybe several.

If the trimmer does not start or immediately stalls after starting, then the problem may be in the fuel tank (namely, as fuel), in the spark plug and duct, in the air or fuel filter, in the breather or in the exhaust duct.

1). Be sure to check the presence, and most importantly, the quality of the fuel mixture before starting the trimmer.

2). The trimmer may not start or stall when the candle is filled. It will need to be unscrewed and wiped.

It is necessary to dry the candle channel for at least 3040 minutes. Otherwise, a new candle may also flood.

3). If the trimmer starts without an air filter, then it is better to change the old filter for a new one.

4). The trimmer may not start if the fuel filter is dirty.

5). Also, the trimmer may not start due to contamination of the breather.

Also, the reason may be in the ingress of dirt into the exhaust channel or clogging of the muffler mesh.

A gas trimmer may stop starting for several reasons at the same time.

Firstly: try to clean the carburetor - its contamination leads to a breakdown of the lawnmower.

Secondly: A vacuum may form in the drum. If so, try making a small slit in the lid of the barrel.

Third: Check if the trimmer setting is correct.

There are several reasons why the trimmer will not start. I will list the main ones:

bad fuel. Each trimmer model requires gasoline with a certain octane rating. Check the user manual and make sure you fill in exactly what you need.
flooded candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
fuel mixture not entering the carburetor. Pump her up a bit.
ignition coil failed.
muffler clogged. You need to free him from soot. To do this, carefully disassemble and clean (can be burned on a gas burner).

Usually trimmer we have won't start after the winter, and we used to take the trimmer to the workshop almost every spring, where they repaired it for us. But once, knowledgeable person advised us, firstly, never to leave gasoline in the trimmer for the winter, because old gasoline can cause the trimmer not to start, and he also said that it is necessary to pump the carburetor to plant the trimmer fuel mixture. After we began to follow these rules, our problems with the trimmer disappeared.
First of all, you can see the candle. If necessary, replace it, making sure that the candle is not broken and gives a normal spark. The next problem will be hiding in the fuel system. As mentioned above, we check the tightness, then we check the fuel filter, change it if necessary. We clean the carburetor, we look at the effect. It may be necessary to delve into the ignition system, adjust. For check fuel system you can pour a few grams directly into the cylinder through the plug screw holes, screw in the plug and try to start. At a minimum, the trimmer should make sounds of a running engine for 1-2 seconds and some smoke should fly out of the muffler.
If your trimmer does not start at all or immediately stalls after starting, then you first need to look for the cause in the main components and assemblies, for this you need to check in the sequence below, so here is this sequence:
In these nodes, basically, the whole problem may lie.
1) Check the fuel mixture itself
2) We examine the candles and the channel:
3) Inspect the filter:
4) Breather and exhaust port:
But also the probable reason may lie in the following:
There may be several reasons. Of the smallest: breakdown of a candle or high-voltage wire. Of the unpleasant ones and which it is not always possible to fix on your own, the electronic ignition unit has been covered. But anyway, check the spark on the candle or on the wire before dragging it to the workshop. Yes, and even there in the carburetor, if there is no separate filter, there is a plug at the bottom, unscrew it - drain the fuel sediment, sometimes this may be the reason.
first of all, their fuel pipes burst ((fuel can’t be sucked in already, the switch may be faulty, for example, it doesn’t turn off well for me, it’s good that it’s not vice versa)) check the pipes, then unscrew the candle, see if it’s dry or flooded, lean pull the starter on the body for a spark. It would be nice to have a spare candle, look at the power button, stupidly for a wire break, somewhere it could fray.
A gas trimmer is one of the most convenient and necessary things if you have a plot. By itself, a gasoline trimmer is, in other words, an ordinary lawn mower, but very compact.
There are several reasons why a gas trimmer starts to stall. Let's analyze the most frequent:
- poor quality fuel. For some reason, many believe that lawn mowers (chainsaws, etc.) can be filled with some kind of stale fuel and nothing will happen. But, it's not. A poor-quality mixture can simply kill the trimmer. Let's skip what exactly low-quality fuel can break, since there can be many options and only a complete diagnosis will help. Let's take the simplest, but at the same time common option - a flooded candle. If the reason is in it, then you can remove it, wipe it and dry it.
- long storage. Trimmers are capricious. They can, if they have lain for a long time, stall at the factory. Then let's do it like this