Not sure how to properly refill a large stationery or mini stapler? Read the article, which describes this process in detail.

A stationery stapler is a stapler for paper and files. You can't do without it either at home or in the office.

• To use it, you need staples, without which the stapler will not work.
• Staples are divided into sizes: No. 10, 26/8, 26/6, 24/8, 24/6. Their numbers are indicated on the packaging.
• On the packaging of the stapler itself, the numbers of the staples that fit it are indicated.
• It seems that everything is simple - insert brackets right size into the stapler and you can start using.
• But many people have problems in order to charge this device. How to do it right, read the article below.

So, you bought staples and want to charge your stapler. How to open and fill a large stationery stapler with staples? Description in the form of instructions:

• Peel back the stapler's plastic cover that is held on by a spring. Opening the roof pulls the spring along with it. The freed space is the groove for the staples. Many large staplers have latches that need to be pushed back.
• Take the braces- one section. Insert them into the groove, the ends should look down.
• Close the stapler cover.
• Click once with no paper. If a paperclip with bent darts falls out, then the stapler is working.

Advice: If the dropped staple is bent incorrectly or it does not fall out at all, then repeat the procedure or buy another stapler, it may be a malfunction.

You can watch the video to learn how to properly thread the stapler. A visual demonstration will help you cope with this process quickly and without problems. In addition, the video tells how to fix the stapler.

Video: how to fix the stapler and charge the stapler?

Mini staplers are easier to refill than large staplers. similar devices. Lift the plastic cover up and back. Now you can insert the staples into the groove. After finishing the filling process, close the stapler and use.

Advice: Mini staplers have a very small compartment for staples. Therefore, if you want to get old staples or insert new ones, then you will need tweezers.

Often the mini stapler can jam during filling. To fix this, open the cover and adjust the staples in the groove. If this is not done, then the stapler may become unusable. Watch the video on how to properly fill the mini stapler.

Video: How to install staples in a stapler?

Video: stapler_stapler.AVI

The first staplers appeared in France in the 18th century, they were specially invented for King Louis XV. But at that time this device was unique - each staple for it was made by hand, it had a coat of arms. It was only at the beginning of the 20th century in the States that the stapler was made accessible to most people.

Types of staplers

In stores specializing in the sale of stationery, you can find various devices for binding papers. There are so-called pocket options. This category includes any stationery stapler that can be safely placed in the palm of your hand. The body of such devices is usually made of plastic. They can stitch a small number of sheets at the same time. Their main advantage is their low price. But it is worth remembering that they are not suitable for intensive work. At active use they will have to look for a replacement very soon.

In offices, desktop staplers are most often bought. It is undesirable for them to fasten papers on weight. The devices are designed to operate on a hard, level surface. At the bottom, they usually have a special anti-slip coating that prevents them from moving around the table even under load.

A large stationery stapler differs even in its own way appearance. It is equipped with a special lever, which must be pressed in order to fasten sheets of paper. The most powerful models are capable of fastening up to 260 sheets at the same time. Often they are equipped with special tools designed to remove bent staples. Some devices have a special fixing bar. It is designed to adjust the bonding depth.

Stitching types

Not everyone knows that stationery staplers differ depending on how they fasten the sheets. Most office workers are familiar with the usual options closed type stitching. Such a stationery stapler bends the edges of the staples inward. This is considered the most reliable way to bind paper. It is also the most common.

There is also open type. In this case, the staples are bent outward. This method is preferable to use in cases where only temporary stitching of sheets is necessary. The papers fastened in this way are easy to separate, while the traces are practically invisible.

Sometimes offices use a special stationery stapler with straight staples. It is necessary in situations where it is necessary to attach paper (some kind of announcement or document) to a special board with a soft surface. It can be made, for example, from cork.

Important nuances

When purchasing a device for connecting papers, it is important to consider how actively you will use it. If you plan to use it often, then pay attention to metal options. They are considered more reliable and will last longer. In other cases, ordinary plastic devices will do. The principle of their work is absolutely the same.

It is also important to consider that staplers vary in power. This indicator determines how many sheets your device can fasten at a time. By the way, it is also important to choose the right brackets for stapler. It is desirable to know not only their size, but also the manufacturer. It should be noted that thicker brackets are required for more powerful devices. Otherwise, they will bend and break when trying to flash a stack of papers with them.

In addition, you need to know that there are devices that work only when you focus on a table or other flat surface. If with such a stapler you try to fasten the papers on weight, then the staples will fall out or deform.

Additional options

It seems to many that a stationery stapler is a fairly simple device that cannot be improved in any way. But manufacturers make it more convenient to use. So, when buying, pay attention to the fact that there is a plastic footboard or rubberized inserts at the bottom. They will protect your table from scratches.

Another important and convenient addition is the presence of a built-in destapler. This is a special device with which you can quickly unbend the staples. It is useful in those situations when you need to separate previously fastened sheets. Opening the staples with scissors, and even more so with nails, is inconvenient, and it looks unsightly.

Principle of operation

If you are serious about choosing a paper binding tool, then you will be interested in the device of a stationery stapler. Staples are inserted into a special metal chute. They move forward with the help of a spring or a special plate.

It is worth noting that the second option is considered more practical. This is due to the fact that the springs tend to stretch over time, they can slip off the hooks on which they are attached. The plate is able to provide smoother operation of the moving tongue. It contributes to the fact that the clip of the staples is always fixed at the edge. The push tab can be made of metal or plastic. In the first case, it will be more reliable.

Loading the stapler

Staples are inserted into the internal mechanism, which, when the device is sharply pressed, shoot and fasten the sheets. When the clip ends, it simply needs to be replaced with a new one.

If you have a full-load stapler, then you need to insert 1 new staple clip plate into it. But there are other options - they put ½ of the clip. The usual pocket and office options are easy to deal with. To change the plate of staples, you do not need to look for what the clerical stapler looks like. Just enough to lift top cover and insert the clip into the groove.

There are special models with front loading. They have a button on the body, by pressing which you release the spring of the mechanism. The chute moves forward.

A little harder to deal with professional devices. In some of them, even 7 types of staples can be loaded. At the same time, users have the opportunity to adjust the depth of attachment.

Device repair

If you had an ordinary pocket or small desktop stapler, then if it breaks, it is best to buy a new one. But there are some problems that everyone can fix on their own.

First of all, it is necessary to remove the body and remove the clip from the gutter. So you can see that the staples are stuck at the exit of it, which interfere with its normal functioning. This is usually the main cause of failure.

In order for the stapler to start working normally, it is necessary to remove all stuck staples. This can be done with tweezers or a thin screwdriver. The main thing in this case is not to damage the chute itself, the spring and the pusher. After that, you can remember how to assemble a stationery stapler. It is necessary to insert the spring into place, if you removed it, install the case and press the upper part to the lower one so that they lock into place.

Furniture stapler is enough universal tool, with which you can not only perform the furniture upholstery procedure, but also a number of other construction operations.

To date, there is one that differs from each other in the principle of operation:

• pneumatic,
• electric,
• manual.

Pneumatic staplers are used in industry, while electric and manual staplers are used in everyday life. Models belonging to the latter type are the most common in the furniture industry due to their mobility and ease of use. Let's use this example to consider the principle of operation, operation and repair of furniture staplers.

However, before proceeding to this procedure, I would like to say a few words about brackets and their varieties.

The main indicator that is guided by when choosing a bracket is its depth. Depending on the nature of the work performed, this indicator can vary from 4 to 14 millimeters.

So, for example, in order to carry out the procedure for upholstery of furniture with fabric, a bracket with a depth equal to 8 millimeters will be enough, while for fixing thicker materials, a bracket with a greater depth should be selected.

Also, depending on overall dimensions, brackets are divided into the following types:

• 53 - is the most common. Staples of this type have a width of 11.4 mm and a thickness of 0.7 mm. Depth given fastener varies from 4 to 14 millimeters;
• 140 - having the following characteristics: width - 10.6 mm, thickness - 1.2 mm, depth - similar to the previous type;
• 36 - such a marking means that the stapler can shoot staples that have a semicircular shape and are used mainly for cable installation;
• 300 - These are special nails intended only for the stapler.

When choosing a bracket, you should also consider the structure of the material from which it is made.

Regular steel staples are great for working with regular wood. However, if you are dealing with particle board or plywood, then you should purchase staples made from hardened steel, as ordinary ones can simply bend.

Manual construction stapler has a magazine into which a clip with staples or special nails is loaded. The striker hits the bracket, which is attached to the drummer. The size of the striker in the tool depends on the dimensions of the used Supplies(bracket). The drummer, in turn, touches the spring, the degree of compression of which is regulated by a special screw. The impact is damped using a shock absorber, which is located inside the stapler.

See the stapler device in the diagram:

Stapler device with twisted mainspring

A twisted mainspring is installed on inexpensive models.

Manual stapler with lamellar (spring) mainspring

The leaf spring stapler is more powerful and expensive.

How to use a stapler

Refueling

In order to fill the stapler with staples (i.e., charge the staple gun), you must first move the spring that is intended to press them. The staples themselves are placed in a special groove, in which, in fact, they must be placed. After that, the spring is put in place. The tool is completely ready to work.

Video: how to fill the stapler with staples

Now you know how to insert the staples into the stapler, we can go directly to work.

Shot

In order to fix necessary element, you should firmly attach the device to the place where you plan to hammer the bracket. After that, without lifting the device from the surface, it is necessary to press the button (lever) of the trigger mechanism. If these manipulations are successful, you will hear a characteristic sound and see the bracket that has entered the material.

To protect yourself when working with construction stapler, some rules should be followed:

• In the case of using a mechanical model of the device, it is necessary to adjust the screw regulator. This operation should be performed on a piece draft material by turning the screw from minimum to maximum. If the bracket went all the way from the first shot, you can start working on the “cleaner”. Otherwise, re-adjustment is required;
• In order to drive in staples at the same distance, you must first mark the necessary places with a pencil or ballpoint pen;
• Hold the material with your free hand so that when fired, it does not move from a predetermined place;
• Keep track of the number of staples in the "store" so as not to be left without a single fastener at the most inopportune moment;
• After finishing work, fix the handle with a fuse to prevent spontaneous or accidental firing.

In addition to all the above tips, you may also need help to repair this construction tool, since the stapler, however, like any other equipment, tends to break.

Repair

The most common cause of stapler failure is impact mechanism failure. However, in order to get to it, you must first disassemble the tool. This can be done by performing a number of simple operations:

• Remove the adjusting screw;
• Remove spring;
• Remove the protection cover;
• Remove the pins;
• Remove lock washers.

If according to the list of actions it is not clear to you how to disassemble the stapler, then you can see this in the video below.

After performing all the above manipulations, you will be able to see the drummer, which, for the most part, fails due to the exhaustion of its resource.

In order to repair this element, it is necessary to remove it, install it in a vice and, using an ordinary file, give the drummer its original shape.

Everything, the repair is over, and the tool is again in full combat readiness.

Tips why the stapler does not work and how to fix it:

• If your tool does not finish shooting (does not finish off) the staples, then try tightening the spring, it may have weakened;
• If the stapler bends the staples, try adjusting the spring tension bolt (relax or tighten, experiment). Another likely cause of the malfunction is a mismatch between the type of staples and the structure of the material - for chipboard and plywood, it is recommended to buy hardened steel staples;
• If the staples do not come out of the stapler, but bend and get stuck inside, it is possible that the striker (tongue) that pushes them is rounded and needs to be sharpened;
• If the mechanism itself works, but the bracket does not shoot, it may not grab the bracket, the striker has worn out. Try filing the firing pin and turning the damper on the other side.

How to repair the staple gun with your own hands, see the video.

Video: do-it-yourself stapler repair

How to disassemble furniture stapler what to do if he jammed. What could be the reason for what to do if the construction stapler does not shoot staples:

The real-time video shows step by step how to disassemble the stapler, what could be the cause of the breakdown and how to fix it yourself, as well as how to assemble the stapler.

Video review of staplers

You can also watch a short video on the review of furniture staplers, as well as the principle of their filling, setting and working with them:

Good luck to all home masters, there will be questions - write!

These convenient and ergonomic devices have won well-deserved appreciation from both professional furniture makers and home craftsmen. On sale there are even such models of staplers that can work with small carnations. Using a hammer with almost inevitable injury is slowly becoming a thing of the past. In addition, the speed of work is significantly increased. However, this design sometimes falls into disrepair. Throwing away the old stapler, frankly, I don’t want to. Let's talk about how to repair a furniture stapler with your own hands.

Classification

There are such types of furniture staplers.

Manual

Staple hammers

These devices clog staples strong blows. Compared to manual counterparts, the performance of such a model is much higher. This tool is useful for doing the following jobs:

• Attachment of insulating material.
• Roofing material installation.

Important! In a word, a staple hammer is indispensable where, first of all, fast, rather than filigree-accurate work is required.

Construction cable staplers

This tool is used to install cables with a voltage load of 50 V. The maximum cable diameter is 7.5 mm. These staplers are used when performing such work:

• Cable fixing.
• Laying the electrical network.
• Installation of communication lines.

classic model

Such a tool equipped manual drive has become a true classic. After the trigger is pressed, the clip is driven into the material. A special category is hybrid models, with which you can perform several types of the described operations.

Important! You can also classify all modifications into professional and household. Professional models are distinguished by:

• Convenience.
• Long service life.
• No plastic parts.

They have only one minus: a relatively high price.

Operating principle

Depending on the type of drive, tools are divided into electric and pneumatic.

Electrical

These devices are widely used in everyday life. Working with an electric stapler is a pleasure, you just need to connect the device to the mains. However, an electric appliance, in comparison with a manual counterpart, is much more expensive. it is profitable to buy it for professional craftsmen who are constantly engaged in the repair of furniture. Naturally, for a one-time repair, buying such a model is unprofitable. For domestic use Suitable for manual models.

Pneumatic

In everyday life, these models are not used, since their use will require a compressor unit. You can buy your own compact compressor, but how soon such a purchase will pay off is a question. Therefore, buying a pneumatic device is beneficial for companies manufacturing and professionally repairing furniture.

Sometimes it happens that the stapler refuses to work. Namely, the staples do not fly out of the charger. Before proceeding with the repair, disassemble the device in the following sequence:

1. Remove the adjusting screw.
2. Remove the spring.
3. Remove the protective cover.
4. Remove pins and lock washers.

To successfully repair a furniture stapler, you will need:

• Hammer.
• Vice.
• Screwdriver with a flat sting.
• Pliers.
• File.

Drummer

Carefully inspect the drummer and assess its condition. The most common reason for the incorrect operation of the device is the wear of the thrust pad on the striker body. With the help of the thrust pad, the impact mechanism and the trigger lever work together.

Important! The drummer is the performance part. A spring presses on the striker. You can adjust the spring force with a special screw.

Carbine

The charging carabiner is located at a right angle to the percussion device. The striker contains clips that are acted upon by a spring. Staples in non-working condition are closed by a plate attached to the body of the device.

Trigger system

The trigger system includes the following components:

• Spring.
• Retractable lever.
• Rocker.

How to use a furniture stapler? To hammer in the bracket, you need to press the lever. The rocker raises the drummer. After the bracket enters the striker mechanism, the spring is released. The drummer with force strikes the bracket, and it enters the base.

Rocker and drummer work synchronously. Otherwise, there is a “blank shot”. Need to adjust the stapler for furniture. The trigger worked, but the drummer did not capture the bracket. With strong wear of the thrust pad of the protrusion of the drummer, this is exactly what happens.

To carry out repairs, it will not take very much time:

1. Clamp the striker in a vise.
2. Sharpen the protrusion with a file, giving it its original shape. This will significantly extend the life of the stapler.

Important! It is only necessary to perform this simple manipulation after the device has started to idle. At the same time, the striker plate becomes shorter and needs to be sharpened.

What did you do relatively recently when you needed to change the upholstery upholstered furniture or attach glassine to the frame of a house under construction? They took a hammer in one hand, nails in the other, and then for a long and tedious "bale" on them, and sometimes on their fingers.

Today, few people want to perform such simple operations in an antediluvian way, especially with a large amount of work. After all, there is a stapler for this - a mechanical spring-action staple gun.
Well, if the tool suddenly failed, do not rush to throw it away - repairs can be quite simple.
It is a pleasure to work with a stapler - I loaded a block of staples into the store, put the gun to the right place, pressed the lever - in a moment the material was securely attached to the base. When I needed to insulate attic room country house Isolon (polyethylene foam) with a thickness of 10 mm, I could not get enough - the stapler made my task so much easier. About 70 m 2 of material I attached to the roof slopes in a matter of hours. However, when there was very little left before the completion of the work, the tool began to “fool” - I press the lever, and instead of the bracket, there is only an imprint of the drummer plate. I checked the charger - the store is full.
I began to understand what was the matter (photo 1. 6).
I unloaded the magazine, unscrewed the adjusting screw, and then removed the spring of the percussion mechanism. After that he removed protective covers pistol body, first releasing the pins from the locking split washers, and got close to the drummer. The cause of the malfunction immediately became clear - the thrust pad of the drummer body was developed, which ensures the interaction of the impact mechanism with the rocker arm of the trigger.
To make it more clear to those readers who have encountered a similar problem, but have not yet figured out its causes, I will try to explain in a nutshell the principle of operation of a staple gun (see Fig.).

Typical design of a stapler - staple gun

The main actuating element of the stapler is the drummer. It is under the action of a powerful spring, the compression ratio of which is adjusted using the appropriate screw.
A charger (magazine) is located perpendicular to the percussion mechanism, in which there are staples under the action of a spring. In the non-working position, they are locked with a “strike” (a plate riveted to the body of the drummer).
The interaction of the striker with the charger is provided by the trigger, which consists of a cocking lever, a rocker arm and two return springs.
When you need to drive in a bracket, you press the lever. At the same time, the rocker with its “beak” grabs the drummer by the ledge in the body and lifts it, compressing the spring until the next bracket is in alignment with the striker. After that, the drummer, which is under the action of a compressed spring, breaks off from the beak of the rocker arm, which continues to move along the arc, and the “firing pin” drives the bracket into the base with force.
Thus, the main condition correct operation pistol - the consistency of two processes - the supply of staples and the cocking of the drummer. The drummer should not break off the rocker ahead of time. If this happens, the gun "blanks", i.e. the trigger device is cocked and fired, but the striker does not capture the bracket. It is this situation that occurs when the thrust pad of the protrusion of the drummer body is developed.
It will take a few minutes to repair this malfunction. It is enough to clamp the drummer in a vice and, armed with a file, restore the original shape of the protrusion (photo 7).
In the same way, you can increase the resource of the pistol several times - it is enough to repeat this operation every time as soon as the pistol starts to "blank" again. At the same time, you will have to undermine (shorten) the striker plate.
So do not rush to part with your tool - it will still serve if you do not spare a little time to repair it.

How to adjust a mechanical, manual stapler (staple gun) to finish off staples?

I met two versions of staplers for adjustment, both had to be adjusted.

I must say right away that all these instructions did not help much, I had to lime about a dozen paper clips in order to achieve best result, and then, in the course of work, adjust it every 15-20 strokes. Therefore, the adjustment process is a continuous action during use.

Another point - one builder advised to relax the spring after work so that there was no pressure on it during storage, this is the reason that it needs to be adjusted before each work.

The adjusting screw is located on top of the stapler, inside there is a straight spring along the entire length, pressing on the striker. If the screw is turned clockwise, the impact will be stronger and, accordingly, the paperclip will go deeper. By unscrewing the adjusting screw counterclockwise, the blow is weakened.

In this version, the stapler is made by means of a leaf spring, it is she who presses on the striker and regulates the force of impact. The adjusting screw is under the handle. I do not remember exactly in which direction it is necessary to turn this screw, try it yourself. When you turn it, the plate bends and presses on the striker, or the opposite effect occurs.

the system selected this answer as the best

If the stapler (staple gun) does not finish the staple, then you need to tighten the adjusting stop screw, which will compress the shock spring more and the force during operation will be greater, the adjustment is designed so that the stapler (staple gun) can use shorter staples and not spoil (damage) surface.

So turn the adjusting screw all the way down and everything will be fine!

That's only if the stapler (staple gun) is not designed for the length of the staples and cannot finish them off due to its design features or, frankly, significant wear and tear (sagging of a spring or loosening of a mechanism), then there’s nothing to fix, it needs to be thrown into the trash, since it will only work!

Here is a diagram of a mechanical (manual) stapler.

In order for it to finish off the brackets, it is necessary to compress the spring.

The spring is compressed by a screw, which is most often located at the top of the product itself, that is, in an accessible place.

And it is regulated by a simple twist, tighten the screw, the staples clog more strongly, unwind, the blow is weaker.

It is necessary to regulate starting from what material you are working with, you can pre-train somewhere on an unnecessary piece.

There may, of course, be their own nuances, it's one thing, for example, to nail fabric to wooden frame and another thing PVC lining.

If the adjusting bolt is pinched, then the bracket can pierce through the PVC lining (the brackets are attached to the spike of the lining).

If you constantly work with a stapler with one material, then it makes no sense to constantly turn this bolt, put it out and work, you need to replace the staples, change and do not touch the screw.

If the adjustment is from scratch (a new stapler), then we adjust it from minimum to maximum, working with the same, but rough material (for example, a piece of the same PVC lining), as soon as we visually arrange the depth of the staple, we stop the adjustment.

Construction stapler does not shoot staples

People are doing home renovations or woodworking activities using heavy duty construction staplers to attach pieces of wood and other materials. They can shoot nails and staples when the handle is pressed. When using construction staplers, you must use right size and the number of staples. If a construction stapler does not shoot staples, examine it to clarify the issue.

The stapler does not shoot staples: instructions

1. Check the number of staples in the stapler, if none comes out. Look through the side viewing window stapler. Reload the stapler if you don't see any staples inside.

2. Turn the stapler upside down. Click on the latch. Pull it open to see how many staples are available.

3. Check the size of the staples to determine if they fit the stapler. Replace with new braces if you are not using the correct size. Put them in the stapler with the pointed ends facing the container.

4. Pull out the bracket if it is stuck in the opening where it should come out. Pry the curved and angled staples with the tip of a knife until they are easily removed.

Friday, August 8, 2014

How to choose, operate and repair a furniture stapler

Types of furniture staplers

Varieties of staplers according to the type of effort applied: