How to cut tiles at home. How to cut a tile: we tell briefly and without further ado. Hole drilling technique

They do not always fit entirely in the last row. Also, their size must be adjusted in the areas of communication outlets, the location of plumbing, etc.

IN this material Let's talk about how to cut tiles.

There are several tools for cutting tiles, they are divided into two large groups:

manual;
electrical.

Each variety is worth considering in detail.

Manual

This group includes glass cutters, tile cutters, wire cutters. A manual glass cutter is like a ballpoint pen with a roller at the end.

The roller is made from the following materials:

hard alloy;
diamond.

The second variety is the hardest and most durable. The glass cutter is used as follows: pressing it with force, it is rolled over the tile along the ruler, as a result of which a groove appears on the material. Next, the module is broken along this groove, laying it on the edge of the table or placing a bar under it.

Disadvantages of a glass cutter:

suitable only for the thinnest wall tiles;
unable to cut along a curved path.

Most practical oil glass cutter. In the handle it has a cavity for lubrication - a mixture of oil and kerosene. Through a thin channel, it enters the roller and facilitates its rotation.

Nippers are designed specifically for cutting tiles. On the bottom there is a cutting roller, the same as the glass cutter. Having drawn a furrow, the master grabs the tile with the jaws of the cutters (one of them is flat) and breaks the fragment along the drawn line.

Tile cutters

Advantage: you can bite the material along a curved line. Disadvantage: fragments of small width are cut off at a time. acts in the same way as a glass cutter - it makes a groove with a diamond roller, after which the tile is broken.

But the working tool is fixed in the carriage, moving along the guides and equipped with a lever. Thanks to the lever and precise positioning of the roller, the master has the ability to put pressure on it with more effort than in the case of a manual glass cutter, so the tile cutter copes with the thickest tiles and even with.

The tile is placed on a frame with anti-slip pads and a stop that prevents the tile from moving and turning. Some models are equipped with a ruler - it allows you to accurately measure the width of the part to be cut. For cutting at an angle, you must choose a fixture with a swivel base.

Manual tile cutter

Breaking tiles is done right there, on a tile cutter. To do this, there is a round stop at the base, and support legs on the movable carriage. The master sets the paws on the tile and breaks it with pressure on the lever.

Signs of a quality manual tile cutter:

bearings in the carriage movement mechanism. Bearing tile cutters have two advantages - smooth running of the carriage (this is a condition for an even cut) and durability. Cheaper tools with bushings instead of bearings have a smooth running only in a new condition; after a short operation, the carriage moves with jamming;
lack of backlash in the carriage. If there are gaps, the roller will not be able to correctly draw a groove, and the tile will break unevenly;
stiffening rib at the bottom of the base, preventing its deflection. If the base bends when broken, the tile will break crookedly.

Electrical

Metal discs are divided into three types:

segmented (dry cutters). Most often used. The disk is divided into segments by radial slots, which ensures efficient heat dissipation, so it can be cut without liquid cooling. After working for a minute, the disk is allowed to cool by rotating it for 20 - 30 seconds. at idle. The cutting quality is low, the process is accompanied by intense dust formation and vibration;
solid (wet cutting blades). Without cooling with water, they work no more than 15 seconds, so they are almost never used with angle grinders. But the quality of their work, compared to dry cutters, is higher, so some prefer to purchase special device for water supply, attached to the casing of the angle grinder. An important advantage - when wetting does not emit dust;
combined. They cut both dry and with cooling. In terms of quality and duration of work without water cooling, they are located in the middle between dry cutters and wet cutting discs.

Cleaning of dry cutters and wet cutting discs from debris that has clogged them is carried out by rearranging the other side. This cannot be done with combination discs: they have an arrow indicating the direction of rotation, and this requirement must be followed exactly. Such disks are cleaned by cutting concrete or cement-sand bricks.

The most durable cutting discs with diamond coating, it is fixed in different ways:

by means of hard solder. Such discs are cheap, but when overheated, they lose their coating and therefore do not last long;
geometric closure method. Diamond chips are fused into the edge of the disk heated by electricity. It keeps more reliably, while the disk, although it becomes more expensive, remains affordable;
laser soldering. Very expensive and extremely hardy discs. Usually used in industrial installations.

How to choose the right cutting tool?

The tool is selected taking into account the scope of work:

A circular saw is used to cut tiles only if one is already available. Purchasing it specifically for this purpose is unreasonably expensive.

How to cut tiles without chipping?

The guarantee of an even cut without chips is the observance of the following rules:

Before cutting, it is useful to soak the tile in warm water for 40-50 min. (except for porcelain stoneware), this will give a triple effect:

ceramics will soften, and it will be easier to cut;
the number of chips will decrease;
there will be less dust (when cutting with a disc).

Withstand tiles in water for more long time not worth it - it will deteriorate. It is possible to supply water to the cutting zone when using a grinder without a special device.

Craftsmen attach a hose to the tool casing with clamps and connect it to the water supply. An easier option is to invite an assistant and equip him with the same hose or spray gun made from a plastic bottle.

Water cooling allows:

improve cutting quality through the use of a solid disc;
avoid dust emission.

When using an electric tile cutter with a bath under the desktop, the water in it is often changed. Otherwise, the debris accumulated in large quantities is captured by the disc, which leads to a deterioration in the quality of the cut. If you don’t want to mess around with this, you need to choose a model with running water supply.

Alternative tools, features

There are many ways to cut tile without equipment using the following tools:

Cutting accessories

An angle grinder is a grinding unit that, when using special nozzles with diamond coatings, cuts tiles, other materials (even floor tiles, porcelain stoneware).

Glass cutter - a device that has a size ballpoint pen and copes well with tiles, but the work requires confidence and clarity.

Drill - suitable for rounding, holes, while using different nozzles (drill, ballerina, crown).

Pliers - the edge of the tool cuts upper layer tile, makes a break line. Often used for curly cuts.

In addition to these tools, they use a spray saw, a jigsaw, even a nail. .

Attention ! When working with tiles, diamond-coated nozzles are used - others do not cope, spoil the material.

Work technology

Cutting tiles with a glass cutter

Affordable simple method cutting tiles is considered to be the use of a manual glass cutter, which functions on the same principle as a mechanical glass cutter, only the operations are performed manually. The most suitable for the job is a tool with diamond tips and a roller made of durable alloys.

Glass cutter - an affordable way to cut tiles at home

When performing work, follow a certain sequence:

The first step is to mark the incision with a marker or pencil on front side.
Lay it on a hard flat surface.
A ruler is applied to the markup.
A manual glass cutter is applied to the far point away from you.
Pressing on the ruler (so that it does not move) and on the glass cutter, draw a line from far edge to yourself. In this case, the cutter should not be pressed hard. When drawing a line, a crunch is heard, at the end the glass cutter should jump off the tile.

Attention! The incision line is made so that a visible mark remains on the enamel. Do this only once, because when you cut it again, the tile will break unevenly.

The broken line that has appeared is tapped wooden handle glass cutter.
The tile should be set so that part of it is overhanging.
On the exposed edge of the tile, which is placed on a table or other flat surface, they press, break along the line that was drawn. If the line is deep enough, then the fault is obtained without chips, neat, even.

You can break the product along the fracture line if you put a carnation, a match under the tile, press from 2 sides. This method of breaking is popular with a large amount of cutting - time is saved on transferring the tile to a flat surface for breaks.

In this way, cuts into strips of more than 5 cm are well obtained, but it is difficult to break off smaller strips of high quality. To do this, at home they use a bar, a clamp: the narrow part is clamped, and the wide part is broken off with a sharp downward movement.

A manual glass cutter is used when several tiles need to be cut. In case of a large number cuts, it is advisable to use a special tile cutter tool, which has a large wheel that makes a deep cut.

Cutting tiles with a grinder

Initially, the grinder was used for cutting marble, porcelain stoneware. Cutting with a grinder is noisy work, but this method is widespread. With this tool, even difficult corners are cut out of tiles. To work, you should prepare a tool:

Bulgarian.
Roulette.
Marker (pencil).

Regardless of the type of tile (ceramic or porcelain stoneware), the first step is marking. To do this, use a ruler, building corner, tape measure, marker or pencil.

When working with a tool such as a grinder, one should not forget about safety precautions: the machine must be with a protective cover, which, in which case, will take on the main impact force. Be sure to wear safety goggles. After following the safety rules, they are taken to work.

Before starting work, check the reliability of fastening the diamond wheel on the spindle. Other types of discs will not cope with this task. After turning on the machine, wait until it picks up speed. Only after that they start cutting along the intended line.

We cut the material on the front side towards us, i.e. along the path of the disk. The car is held “upside down” so that the disc spins “away from you”. To obtain a straight cut, angle grinders are held evenly. To get a cut at 45 degrees, the tool is fixed on its side. Due to the high speed of the disc, the cut is smooth, clean.

Attention! The tile should be well fixed so that nothing interferes with the cutting element, the tile does not move and is on the surface of the support. Be sure to fix the sides with clamps.

The cut can be carried out in several approaches, gradually plunging the saw deeper without losing momentum, so you should not press. For best cut before each approach, the cut line is abundantly moistened with water.

Advice! The quality of the cut will improve, regardless of the chosen cutting method, if the tiles, for example: for the floor, are left in water for an hour before work.

Alternative fixtures for glass cutters

When there is no glass cutter, angle grinder in the house, you can use a strong sharp object to mark the furrow. Suitable:

cutter;
file sharpened with emery;

Cutting with drill drill

victorious drill;
construction knife;
alloy steel, others.

The main thing is to hold such an object in your hands when making a furrow. To draw a cutting line with a construction knife, you will have to draw a line several times.

In emergency use circular saw although she doesn't have high speed. An appropriate disc (coated) is selected, the shaft is accelerated to the maximum speed. Then slowly, without pressure, a cut is made along the intended line. The cut is made submersible, longitudinal, necessarily wetting the cutting point with water.

Figured cutting of tiles

Sometimes curly holes should be made in the tile for laying near the pipe, plumbing. This can be done in the following ways:

drill;

Curly cutouts

grinder;
pliers;
jigsaw;
glass cutter.

How to cut a tile with a grinder, a glass cutter is clear - but how to work with pliers? Draw a cut line on the tile. Then break off small pieces with pliers. With this task, wire cutters with a clamp do a good job. The top carbide clamp cuts the glazed surface, while the bottom holds the workpiece from below.

When using a drill, ordinary drills are used to outline the contour, and then break off the extra pieces with wire cutters. All sorts of nozzles will help to effectively make figured cutting of the material: a feather, a crown, and others.

Attention! You should not bite off large pieces - the edge of the cutout will be of poor quality, ugly. Additionally, after working with wire cutters, they use a special sandpaper, a file for cutting irregularities.

Holes in tiles are made with hole saw, which has a carbide tip for making round holes. It is used when creating curly cuts of tiles. The tool is suitable for hard and soft tiles. Saws slowly, collecting a lot of dust around him. Therefore, the product should be dipped in water.

Each method of cutting tiles without a special tool is good in its own way. You can cut the product with the help of improvised devices. Of course, the performance will be low, but with small volumes, this is an economical way out.

Cutting tiles with a hand tool:

Cutting tiles with a grinder:

When planning the laying of tiles, you need to decide how to cut ceramic tiles. Facing material is available in several versions, and for each type of tile there is a priority method for cutting it. You will learn more about how to cut various tiles, and what devices exist for this.

Varieties of facing material and features of its various types

The basis of most types of tiles produced now is baked clay - ceramics. On the front side, the tile is covered with a thin, but more durable waterproof coating, which at the same time carries an aesthetic load. Facing material is divided into two types:

wall-mounted (for finishing vertical surfaces);
for floor cladding.

Floor tiles can be internal and external (for laying on thresholds, verandas, terraces). Floor cladding material intended for indoor use is usually made with a smooth front surface, outdoor tiles often has special anti-slip protrusions or a rough surface, which is taken into account when choosing a cutting device.

With wall cladding material, too, not everything is simple. In addition to the most common tile, which has a smooth decorative surface, there is a tile with a relief finishing layer (including a frieze - separating elements between the panel part of the wall and its "top"). Not all methods that allow you to cut a smooth tile are suitable for a corrugated surface.

When choosing how to cut a tile, its thickness, strength, area of \u200b\u200bthe proposed lining and the complexity of the geometry of the pattern are taken into account. Wall tiles are thinner than floor tiles, their strength is lower, so a regular glass cutter or is suitable for cutting them. Floor cladding material requires a more serious tool, especially if its surface is rough or has anti-slip protrusions. If a lot of complex patterns are expected (holes for sockets, bypassing pipe communications), care should be taken to have devices for curly tile patterns.

When determining with which device to cut tiles at home, the volume of the intended finish should be taken into account. For small areas and a simple pattern, a simple tool will do. If there is a lot of work, it makes sense to use more advanced devices so that it does not take longer to cut the tile than to lay it.

Now ceramic tiles are cut using several devices that differ in design complexity and functionality.

Glass cutter - an inexpensive option for small volumes

If you have to cut ceramic tiles at home, while the cladding area is small (for example, a kitchen panel), an ordinary glass cutter is suitable for work. These simple tools can be equipped with a cutting wheel or a diamond tip. Choose a glass cutter that has worked or which one you think is more convenient - you can cut tiles with any type of tool.

How to cut tiles with a glass cutter correctly? The essence of the process is identical to working with glass: you need to scratch a groove on the front surface, which will become a fault line. To do this, first we take the dimensions of the fragment necessary for laying, make the appropriate marks on the decorative side of the whole tile and draw a straight line with a marker corresponding to the intended cut. The tile is laid on a flat surface, located at a height convenient for work (table, workbench). The working part of the glass cutter with an average uniform pressure is moving from the far end of the tile towards itself.

In this case, a clear shallow furrow should form without interruption areas. To make the cut as even as possible, you can use a guide bar. But it is better to make an incision under visual control, combining the cutter with the drawn line. It is not advisable to run a glass cutter twice along the same line - it is very difficult to get into the same furrow a second time. As a result, the incision will not be of very high quality. You need to try to make a furrow in one motion.

Then we do the following. If the cut-off part is more than 3-4 cm, the tile is laid on the table (face up) or other hard surface so that the cut line coincides with the edge of the stand. We lay the wider part on the table, the narrow segment hangs down. Holding firmly that part of the tile that lies on the table, you need to sharply press on the hanging fragment, as a result of which it breaks off exactly along the drawn groove. When the width of the cut off fragment is small, another tactic is used - the excess part of the tile is gradually broken off with special wire cutters. If they are not at hand, you can use ordinary pliers for these purposes.

Cutting tiles with a glass cutter requires skill and firmness of the hand. These qualities are acquired quickly, so do not be upset if the desired result does not work the first time. To quickly acquire a skill, you can sacrifice one tile, and make many different strips and rectangles out of it, making cuts with a glass cutter, and then proceed to the pattern of the tile fragments necessary for laying.

The glass cutter is suitable for working with smooth wall tiles. The corrugated surface of the tile cannot be cut off with this tool. It is very inconvenient and long with the help of a glass cutter to make circular patterns. To do this, you will have to soak the tile for at least an hour (so that the ceramic base gets wet), make a circular incision, and then look for a suitable stand that best matches the geometry of the intended hole. The tile is laid on a stand and with gradual, gentle pressure, the cut section is forced to separate from the main fragment of the tile. It is problematic to deal with thick and durable floor tiles with a glass cutter, so if you need to cut this type of tile, it is advisable to use more advanced tools.

Manual tile cutter - the best choice for domestic purposes

A manual tile cutter is essentially an improved glass cutter, and its cutting element is the same roller, only more massive and durable, designed to withstand greater force. Increases the pressing force in the device under consideration, the lever, which forms a single mechanism with the cutting wheel and is fixed on a carriage moving along two parallel skids. The guides are fixed on a frame equipped with a support from below, on which the cut tile is laid. On the stand, according to the course of the cutting element, a metal protrusion is built in, which serves as a stop when breaking the tile. A special device (press) is movably attached to the movable carriage next to the cutting roller, with the help of which pressure is transferred from the lever to both halves of the cut tile.

There are many models of manual tile cutters that differ in the following characteristics that affect the performance of the fixture:

the maximum size of the tile that can be cut;
sliding mechanism of the carriage along the guide skids (dry running, lubrication, bearings);
backlash of the cutting element;
material for the manufacture of the main parts of the device;
equipment accessory for cutting circular holes.

With a better performance of tile cutters, their cost increases accordingly, therefore, when choosing a cutting device, one should understand for what purposes it is necessary. If one-time work on laying tiles in relatively small volumes is expected, it is not advisable to buy a model at a cost above the average - an inexpensive product will do. When there are large tile laying areas in the plans, it makes sense to purchase a model more expensive. High-quality manual tile cutters are widely used in their work even by professional tilers.

To properly cut a tile with a tile cutter, follow the following steps:

1. We mark the notch line on the front side, after taking the necessary preliminary measurements.
2. We lay the tiles on the frame so that the drawn line coincides with the longitudinal protrusion on the base.
3. Using the lever, carefully set the cutting wheel on the far edge of the tile (the cutter must coincide with the beginning of the reference line).
4. Slightly pressing on the lever, we stretch it with a continuous movement towards us until the wheel comes off the tile.
5. We raise the lever and install a kind of double-sided press on the tile approximately in the middle of the cut line.
6. We press the lever (not very hard and quite smoothly), as a result of which the tile breaks into two parts.

To acquire the initial skills of using the device, it is advisable to make several trial attempts.

If the tile is large (the cut is longer than 30 cm), it is advisable to press on the cut tile several times, moving the press to different places. So the fault will be smooth and you will not have to modify it.

It is convenient to work with a manual tile cutter, but there are some limitations. This device, like a glass cutter, does not work on a relief tiled surface and some types of floor tiles, especially outdoor tiles, are also too tough for the tool. In addition, the tile cutter will not be able to cut strips less than 15-20 mm.

Water saw – fast, precise and dust-free

A water saw is sometimes called an electric tile cutter, which resembles a circular saw in design and belongs to professional tools with corresponding capabilities and cost. The device is equipped with a desktop longitudinal hole which rotates the cutting disc with diamond coating. The peculiarity of the electric tile cutter is that the cut of the tile occurs in the presence of water, which abundantly wets the disc. It enters the place of the cut through a special pipe (in more expensive models) or the disc is wetted, being partially immersed in a pan with water.

Wet cutting at high blade speed allows you to create an ideal cutting edge that does not differ from the factory one (a chamfer is formed at an angle of 45%). Due to constant wetting, no dust is formed during cutting, as well as chips on the cut-off tile edge. It is possible not only straight, but also curly cutting, the formation of holes of various configurations and sizes. The quality and type of tile only affects the cutting speed, and then only slightly. A water saw will cut a strip of any width from any tile - wall, floor and even porcelain stoneware. Electric tile cutter - the best option to cut what is inside, what is outside, as well as tiles with a relief surface. It does not need to be used when laying facing material covering the cutting edge - it is enough to fill the corner seam with tile grout.

If there is no such equipment at hand (which is not surprising), but at the same time you need to cut different types of tiles, cutting out holes various shapes and sizes, you can use a universal power tool, one of the models of which is sure to be in the arsenal of any home master.

Bulgarian - a universal tool for cutting all types of tiles

corner grinding machines(angle grinders) or grinders - universal power tools with a wide range of applications in everyday life and in small industries. Use grinders and for cutting tiles various types, equipping with special "tiled" discs or conventional circles for concrete ( big difference between the result of these nozzles when cutting ceramic tiles is not noticed).

If there is no tile cutter and other specialized tools, the tile can be cut with a grinder. Any tile is cut with a grinder - wall, floor, porcelain stoneware. At the same time, the surface topography, strength and thickness of the tile do not play a role. The cutting edge is not as smooth and problem-free as when using an electric tile cutter, but taking into account the use of tile grout or plastic corners when laying tiles, small flaws are acceptable.

In order to qualitatively cut tiles without a tile cutter using a grinder, it is advisable to use small angle grinders designed for a disk diameter of up to 125 mm. They are more convenient to work with, especially when cutting and forming holes in tiles. But keep in mind that angle grinders with a small disc diameter usually have high speeds (3600 rpm and above), at which the tile overheats at the cutting point, can crack and numerous chips, so it is advisable to use an angle grinder with an adjustable number of revolutions to work with tiles .

It is convenient to cut tiles with a grinder, but several disadvantages of this process are found:

a lot of dust is formed - it is impossible to work in a closed small room;
when cutting, many small pieces of ceramics fly off, so the process requires compliance with safety regulations and the use of personal protective equipment (glasses are a must, a respirator is desirable);
there is a possibility of electric shock, and in general, the grinder is a dangerous tool.

To cut a fragment of a tile in a straight line using an angle grinder, the necessary measurements are made and the desired area is marked with an indicative line, after which the tile is laid on a flat surface, but not very hard (a piece of board, plywood, OSB boards). It is necessary to cut through the tile to the full thickness only in cases of cutting narrow strips, in other situations only the decorative layer is cut, after which the tile is broken, as described above. Cutting holes with a grinder (circular or rectangular) is done from the back side - this way less chips and other damage to the front side of the tile are formed.

When using an angle grinder to cut tiles, use only new, undamaged blades. Old, worn working wheels will produce a cutting edge with a lot of defects, while there is a danger of their destruction in the process of work, which threatens with serious injuries.

The described tools for cutting tiles are rarely used in isolation - it is much more advisable to combine the use various ways. For example, when laying wall tiles for cutting straight fragments, it’s good to use an inexpensive manual tile cutter or even a glass cutter (quickly, you don’t have to leave the room), but for curly patterns and cutting thin strips, you can sometimes work in open space.

When working with tiles, the question arises: what is the best way to cut ceramic tiles? The choice of tool is determined by the scope of work and the properties of the tile itself. There are several ways to cut ceramic tiles.

How to cut ceramic tiles

In any case, special tools will be needed for the work. The simplest of them is a glass cutter, greater productivity has manual tile cutter, for professionals it is recommended to opt for electric tile cutters. With the acquisition of a certain skill, the tile can be cut with a grinder, and a diamond string is used to make art products.

glass cutter

This is the most simple and inexpensive device for cutting ceramic tiles. It has a different design:

cutting element - a wheel of small diameter;
stylus with diamond tip;
roller glass cutter with oil reservoir in the handle. The lubricant flows down the narrow groove and facilitates the incision.

The cutting elements of the glass cutter can be replaced as the edge is ground down. How to cut ceramic tiles with a glass cutter? On the front side, a cut line is drawn with a pencil or marker. Keeping the ruler on the line, hold the glass cutter in the direction from the far edge of the tile towards you. The goal is to draw a uniform recess that reduces the strength of the tile web.

Important ! Spend on ceramic tiles once! Otherwise, the incision will be uneven and the tile will break unevenly.

Then lay the tile on the edge of the table or other flat surface. The cut line should line up with the edge. Holding the edge of the tile on the table with one hand, the other gently presses on the edge, which is on weight. The tile should break along the notch. Its edges are polished with a file for ceramic products.

With it, cut off durable floor tiles and porcelain tiles up to 15 mm thick. By design, it is a base, carriage skids with a cutting wheel are fixed on it. It is somewhat larger in diameter than in a glass cutter, which makes it possible to achieve a greater depth of cut. Minimum size the wheel is 1.5 cm. It is also removable, it can be replaced after a cycle of work.

Important ! When choosing a model, pay attention to the sliding mechanism of the carriage. It is better if it is made on bearings or self-lubricating o-rings.

On the basis of the manual tile cutter there is a strip of solid material, with the help of which, after the incision, the tile sheet is broken. There is a T-shaped piece in front of the roller on the carriage, which exerts pressure on the two halves of the tile.

The tile is placed on the base of the tool, having previously marked the break line, tightly clamped. The clamping corners must be metal in order to cut floor tiles; enough plastic for the wall. They pull the handle of the carriage towards themselves, making an incision on the front surface of the tile.

The incision is made once. After the end of the incision, press the handle and the tile breaks. The edges will also have to be processed if they fall on the corner. If grout is applied, it will hide all defects.

Cutting ceramic tiles with an electric tile cutter

This tool belongs to the professional category and is quite expensive. With its help, a significant amount of work is easily performed, it cuts any tile quickly, accurately and beautifully. Allows you to make a cut with a width of less than 5 mm, make saw cuts at an angle of 45 degrees, recesses and holes. It is applied for curly cutting. The cut has smooth and slightly rounded edges. In some models, the edge of the disc is immersed in water, in others, the surface at the cutting point is only wetted. During operation, all the dust settles in the cooling tank with water.

It is largely similar in design to circular saw. Consists of a platform fixed on it cutting disc and electric motor.

How to cut ceramic tiles correctly electric tile cutter.

Water is poured into the container so as to cover the edge of the cutting wheel by 2-3 cm.
Tile cutter included.
The ceramic tile is pressed against the machine and slowly moved under the disk, focusing on the marked line.
The blade is moved under the cutting element with a force depending on the strength of the tile. It is not recommended to apply excessive pressure on the knife, as this may cause the tile cutter to stop.
To cut a corner, the tile is gently lifted, unfolded and repeated.

Attention ! When working on an electric tile cutter, you must use safety glasses, gloves and follow all safety rules for handling cutting edges.

It is necessary to monitor the condition of the cutting edge of the disc, replace it in time. Usually diamond wheels are used. Also regularly, as it gets dirty, change the water in the bath.

How to cut ceramic tiles with a grinder

Use new wheels for dry cutting, diamond-coated or for concrete work. Bulgarian is better to use with adjustable speed. At a rotation speed above 3.5 thousand rpm, the tile cracks, and the dust content increases significantly.

Warning ! This is a very dusty and dirty cutting process, so don't do it in a clean room.

How to cut tiles- this question arises before home craftsmen quite often. Why? Yes, because the tile is the most familiar and most convenient to use. finishing material. Of course, the affordability of tiles plays an important role in her choice. Often, craftsmen do not keep complex devices for cutting tiles at home. At best, they have a manual tile cutter at hand, although the cutting process is possible without it.

The principle of operation of this device is similar to a glass cutter. The difference lies in the size of its cutting wheel. It is much larger, which leads to a greater depth of the incision and its greater accuracy.

How to cut a tile with a tile cutter - you will see this in the video, which we attach just below.