Modern industry has presented the owners of apartments and houses with high-quality balcony doors made of metal-plastic profiles.
These near-perfect products fill openings en masse as users find them ideal for use. But they are also subject to various factors, due to which balcony doors must be adjusted for perfect operation.
One of the common problems with plastic balcony doors is sagging. This is expressed in the formation of gaps between the canvas and the upper part of the block box.
The cause of this problem is the large mass of the double-glazed window, which presses on the door leaf during opening or being in the open position.
Also, such a nuisance can occur due to errors by installers who incorrectly set the unit during installation.
To adjust the door in this situation, you can use a hex key, which will have to turn the adjusting screw on the lower and upper hinges mounted on the box.
But first you need to free them from the decorative overlays that cover the mechanism. This is quite easy to do, as they can be easily removed from the hinges.
It is worth noting that both hinges must be adjusted equally so that the load on them is distributed evenly. After checking the operation of the canvas, you can install the pads back.
Another common problem with plastic balcony doors is grazing the vertical profile of the frame.
This offset can be corrected using the same hex wrench, unless, of course, a screw with a different head, for example, with a star, is installed as a fastener.
Unlike vertical shift, you need to rotate the screws on the hinges that are installed on the door leaf itself.
Depending on the direction of displacement, you need to rotate the key clockwise or counterclockwise. In this case, it is necessary to ensure that the sash is in a strictly vertical position and the resulting gap is the same along its entire length. You can check this by eye, but it is better to have the following tool on hand:
- Building level or plumb line;
- Ruler.
It doesn't hurt to have a tape measure to measure the diagonals of the box. There are cases when a balcony block is installed in violation of technology.
In normal working condition plastic doors are pressed tightly against the box profile, creating an airtight seal. But over time, it ceases to be so and a draft appears.
You can check the web pressure using simple sheet paper. It should not penetrate the rubber seal when trying to push it between the sash and the frame.
You can adjust the pressure using trunnions evenly spaced along the entire blade. They are small cylinders that are located opposite the clamping bars mounted on the box. When you turn the handle, these elements cling to them and pull the door tightly.
Each trunnion has a mark that marks the position of the clamping mechanism. By turning the cylinder to the right or left, they are displaced relative to the vertical axis. This way you can make the pressure stronger or slightly weaker, if necessary.
But sometimes it is not possible to adjust the tightness of the sash using the axle alone, since the canvas has sagged a little, although it does not touch the frame.
In this case, you can move it a little clamping bar, to which the cylinder clings and the operation of the mechanism will become more efficient.
It should be remembered that all trunnions installed on the canvas need to be adjusted. This is the only way to achieve high-quality clamping.
It is not always possible to adjust the position of the canvas using only loops. Sometimes it is necessary to move the double-glazed window itself, which, if installed incorrectly, creates an uneven load on the balcony door. In this case you will need:
- Thin chisel or hard metal spatula;
- Rubber mallet;
- Ruler.
First, you need to remove the layout that secures the glass unit in the door leaf. After this, you need to carefully adjust its position, placing plastic pads if necessary.
Correctness must be checked with a ruler. The distance on all sides should be the same. Then the double-glazed window is fixed again with a layout, which is carefully inserted into place and knocked down with a rubber hammer.
Attentiveness and accuracy
You can make adjustments to the balcony door yourself. In this case, the process itself can take place without the help of an assistant, since it is not at all necessary to remove the fabric from the hinges.
But do not forget that any work must be carried out very carefully, otherwise it can lead to damage to the mechanisms. And if this happens, then it will be impossible to do without a replacement.
In order not to let the door wear out completely, you need to pay attention to its operation.
If somewhere the profile begins to touch or when closing the sash does not move towards the frame, pressing tightly, then it is better not to waste time and immediately make adjustments. The rest can be done by a simple home craftsman.
Also look at the video for examples of adjusting balcony door fittings:
Plastic steel doors a worthy alternative wooden, both in appearance, and in cost, and in terms of wear resistance. To ensure high durability, it should be remembered that any mechanism needs periodic adjustment, so adjusting plastic doors is a mandatory procedure. Next, we will look in detail at how to adjust a plastic door yourself, using a minimal set of tools.
Adjusting a plastic door is a very real task.
Before adjusting the doors yourself, study the documents for the purchased product. Firstly, there may be detailed instructions for setting up this particular model, and secondly, you should make sure that the warranty has already expired, because if the door is under warranty, then one call is enough, and it will be set up for you.
Setting up entrance and interior plastic doors with your own hands differs from adjusting plastic doors. balcony structures. This is caused by several reasons:
- Plastic thickness and profile configuration for balcony and interior doors different. By the way, the design of the entrance and interior doors is almost the same, so the adjustment of the plastic entrance door is carried out in the same way as the adjustment of the interior door.
- The adjustment of plastic entrance doors is mainly carried out by adjusting the hinges, and additional fittings and handles are involved in the adjustment of balcony doors.
- The balcony door is often equipped with a folding ventilation mechanism, which is also adjustable, while its entrance and interior counterparts do not have a folding ventilation mechanism at all.
- How to adjust plastic doors is largely influenced by the weight of the structure. Often, a balcony door is almost half the weight, which means there are fewer adjustment and locking screws in the design.
How to properly adjust a plastic balcony door is written in detail with examples and explanations. If your plastic balcony door is completely jammed, then there is information about the causes of the breakdown and methods of repair.
When to Adjust Doors
Any, even the most expensive and beautiful plastic door, sooner or later needs adjustment. The need for periodic adjustment is caused by the following reasons:
- The building itself may sink. In this case, the box slightly warps.
- Problems may be caused by incorrect installation. Here errors will appear within a month. As a rule, the door closes tightly or poorly.
- Incorrect or intensive use. Often this requires adjusting the hinges and replacing the seal.
- Doors can sag under their own weight. Here the hinges are also tightened in height, plus sometimes the pressure of the plastic door needs to be adjusted.
Before adjusting a plastic door, you need to diagnose it. This will give a clear understanding of which node needs to be configured.
First things first, take a look. door leaf and a receiving box around the perimeter. Minor abrasions indicate that the door has sagged. Immediately mark these places with a pencil.
If you notice that it has begun to leak through the doors, it means that there is a gap somewhere along the perimeter of the canvas. It is useless to examine the clamp with a lit candle in plastic doors; the flame will begin to fluctuate only if there is a very large gap, while small cracks are covered with a seal, and the candle does not react to them.
The sagging area can be identified using a sheet of paper. You need to insert a sheet of paper between the frame and the door leaf, then close the doors and try to pull the paper out. If the pressure is good, the paper will sit tightly, but if the pressure is poor, you will pull out the sheet freely. This way the entire perimeter is examined.
It happens that the door clamp has absolutely nothing to do with it, the rubber seal is simply worn out or damaged in some area. In this case, you must first replace the seal and then check the pressure.
To identify the curvature of the door leaf horizontally and vertically, you need to completely close the doors and trace the leaf along the contour with a simple pencil. Next, take a ruler and measure the distance from the drawn line to the edge of the box.
Vertically you need to measure at three or four points, horizontally at two or three points. Although sometimes without measurements, the naked eye can see where the doors have moved.
Not so often, but it still happens that the cause of problems with doors is the locks themselves, the strike and locking strips of the locks, as well as the latches and the door closer. Therefore, when diagnosing, we recommend disconnecting the closer first, and then checking the lock group. If everything is in order there, then you can begin checking according to the scheme described above, that is, searching for abrasions, checking the pressure with a paper sheet and outlining the outline of the canvas.
By the way, if you find out that the reason is in the closer, then information on setting it up can be found.
Technique for adjusting various components in plastic doors
It is impossible to say unequivocally how to adjust a plastic entrance door, because the fittings are produced by many companies, which means that its adjustment scheme may differ in each individual case. As already noted - if there are problems with closing entrance doors and the locks are fine, which means you need to look at the hinges.
If the doors are equipped with GreenteQ hinges
Regardless of which company manufactured the hinges, in all such mechanisms, plastic doors can be independently adjusted in three directions:
- The door does not close tightly, that is, the clamp.
- Vertical is when the door needs to be raised or lowered.
- Horizontally - this is when it is necessary to pull the canvas to the right or left.
Door hinges from trademark GreenteQ is equipped with almost half of the plastic doors that exist today. Plus many competitors simply copy general principle the operation of this mechanism, so we will focus on it.
To get to the regulating system, you first need to remove three plastic plugs: on the top, bottom and side.
Next you need to remove the decorative trim itself. To do this, you need to open the door and unscrew the fixing screw, which is located on the inside of the hinge. In GreenteQ hinges, this screw is made for a Phillips screwdriver; there are also screws for a flat-head screwdriver and a thin hexagon.
The pressure on GreenteQ hinges is adjusted by the upper vertical eccentric. This mechanism is located on the part of the hinge that is attached to the door leaf.
You need to insert a 4 mm hexagon into the eccentric and then turn it clockwise or counterclockwise. By rotating the hexagon, you can adjust the clamp by approximately 0.75 mm.
If a play of 0.75 mm does not suit you, for example, due to replacing the rubber seal with a thicker one, then you can replace the gasket under the part of the hinge that is fixed to the box. These gaskets are sold. The thickness ranges from 1 to 5 mm, in 1 mm increments.
The hinge spacer can have a thickness from 1 to 5 mm.
The horizontal mechanism of this model is adjusted with a side screw. The screw head is made for a 4 mm hexagon, and the screw itself is part of a horizontal structure. To adjust the hinge, you must first loosen the six mounting screws using a Phillips screwdriver. You don’t need to completely unscrew the screws, just loosen them slightly so that the mechanism moves.
To adjust the door leaf vertically, you need to tighten or loosen the bottom screw. It is noteworthy that the door, adjusted at the factory, lowers only 1 mm and rises 4 mm. This paradox is caused by the fact that the canvas often needs to be lifted, as it sags under its own weight.
Plastic doors - vertical adjustment of the door leaf.
After all the settings, the plastic decorative trim is closed, the internal screw that secures this trim is screwed in, and the plugs are installed last.
Setting up the hinges of the WX model
If GreenteQ type hinges are installed on both interior and entrance plastic doors, then the WX model hinges are more designed for heavy street doors, and they are installed not only on plastic, but also on aluminum structures.
First, the decorative caps are removed from the bottom and top. They do not sit tightly to remove such a plug, it is enough to pry it with a knife.
On the inside, next to the lid latch, there is another hexagon locking screw. It directly fixes the mechanism responsible for adjusting the door leaf horizontally. It is not necessary to unscrew this screw completely, just release it.
As a rule, the decorative protective cover in these models is not completely removed; it is only raised slightly. So, when you lift it, you will find an adjusting screw on the side; the doors are adjusted with this screw.
As the screw rotates, the doors will move to the right or left. The maximum stroke here is about 3 mm.
In the hinges of the WX model, you can still adjust the pressure. The mechanism itself is located in the second, mating part of the structure. To see it, you must first remove the cap. After this, also open the door and release the locking screw from inside the hinge.
This mechanism has another locking plug. It is installed on top and made with a hexagon. This plug is unscrewed and removed completely.
Now it's time to adjust the clamp. To do this, a key or some suitable device is inserted into special grooves, and the mechanism is turned. The key stroke is about 90º, the clamping value is +/- 1 mm.
Do not forget that the mechanisms are “delicate”. After adjustment, they must close and the locking screws must be tightened. Closing is performed in reverse order.
A few words about replacing the seal
In this case, the good news is that the window and door seals are almost the same, and most importantly, the replacement principle is no different. Manufacturers promise that a door seal can last 5–7 years, but according to experienced craftsmen, the maximum for rubber seals on doors does not exceed 2–3 years.
Remember, any plastic structure is equipped with several sealing circuits, and the configuration of each of these circuits is different, so it is advisable to take a complete set.
Example of a three-circuit seal for a plastic structure.
It is impossible to adjust the seal; to some extent you can extend its life by lubricating it with silicone, but nothing more. If the tires are worn out, then you only need to change them.
The replacement technology is extremely simple:
- Find the edge of the old seal and, prying it with something sharp, pull it out of the grooves.
- Next, use a knife or thin screwdriver to clean out the remaining glue and rubber from the groove.
- After this, use the same screwdriver or something similar to push the tongue of the new seal into the groove along the entire perimeter.
- To prevent the seal from being torn out of the groove during operation, it is placed on glue, but you need to act without fanaticism, we drip the glue pointwise, in increments of 50–100 mm, otherwise the next time you replace it you will get tired of cleaning the grooves.
Conclusion
If you figure it out, it won’t be difficult to adjust the entrance or interior plastic door through the hinges. great work. This is much easier than setting up balcony or window fittings. Adjustment of other types of doors with detailed photos and the video you can find.
Before each user plastic products, after a long time of operation, a dilemma arises - how to adjust the plastic door? No matter how high the quality characteristics of the door and its components, which are designed to ensure the closing and opening of the PVC door, have, after a certain time the mechanism, one way or another, will need adjustment.
If it is necessary to regulate a PVC door, it would be more rational to contact the appropriate specialists, in particular those who installed it. But, unfortunately, such an opportunity is not always available, and it is unlikely that the technician will be dispatched on the day of the call.
In addition, mastering the skill yourself is not at all difficult, since the process of adjusting a plastic door is not something supernatural. Moreover, customizing plastic products is never a frequent procedure. Adjusting a plastic door is only relevant if you have a complaint about the functioning of the door.
The installation of a new plastic door also includes adjustment work, which is carried out immediately, and for a long time afterwards, the design should not raise unnecessary questions. But after a period of active use, the product will still need to adjust the mechanism, as a result of sagging, poor clamping or the inability to close the door.
Despite the excellent quality and confidence in the organization that installs the door, it is recommended to personally observe the adjustment process to make sure that the adjustment of the plastic doors was carried out correctly.
Upon completion of work related to the establishment of hinges of a plastic structure, pay attention to the following points:
- the frame should be pressed tightly against the box around the perimeter;
- opening and closing the door should be easy, without additional effort, without squeaks;
- use building level to check the verticality of the door;
- check the random opening and closing of the sash. To do this, you need to open the door halfway, and when checking, exclude the influence of wind and draft.
Frequent damage to plastic doors
The most popular defects in product operation are:
- The bottom edge of the sash touches a part of the frame that functions as a threshold. This occurs as a result of the sash sliding under the influence of its weight;
- The canvas touches the middle of the frame. The reason for this is the direct movement of the sash under the influence of various deformations, as well as temperature;
- Poor pressing of the sash to the frame, as a result of wear of the seal;
- Staggering and falling out of the door handle socket.
Initially, it may seem that adjusting a plastic door is a complicated procedure based on the options possible malfunctions. But in fact, you just need to understand which mechanism needs adjustment, and the instructions below will help you troubleshoot problems with your own plastic product.
Adjustment of plastic structure
Before you start installing a PVC door with your own hands, stock up on screwdrivers (regular, flat and Phillips), hex keys different sizes, gaskets.
Competent instructions and necessary tools will allow you to correctly complete the entire cycle with your own hands, and as a result, the adjustment of plastic doors will be successfully and safely performed.
Eliminating sash sagging
To eliminate such a breakdown, you should point the blade upward and slightly move it towards the loop, which is located above. Open the sash, and using a hex key (4 mm), turn the screw on the end of the sash at the top, at the location of the hinges.
To move the sash, make about 1-2 turns in a clockwise direction. After this, close the sash and remove the protective cap from the hinges located below. Turn the screw on the top hinges, slightly lifting the blade. If the sash moves easily, then the problem is solved.
Pressure adjustment
Schemes for adjusting hinges on a plastic door.
To adjust the pressure of the canvas to the frame, it is necessary to use a locking element. It is located inside the sash and acts as eccentrics. The trunnions are adjusted with a special key and pliers.
Do-it-yourself pressure adjustment is carried out in the summer and winter periods, this is enough for the normal operation of the product. In winter, you should independently adjust the pressure tighter and stronger than in summer. It is necessary to press the sash to the frame from the hinge side using adjusting screws.
Horizontal adjustment
Correction of the operation of hinges of a plastic structure can be done in both vertical and horizontal directions. To make horizontal adjustments, first remove the door from the hinges at the top.
Then close it and lift the caps that hide the adjustment screws. To avoid warping the product, tighten the long screw at the top hinges slightly with more force than at the bottom. To ensure uniform movement of the sash, remove the trim from the hinges and tighten it by loosening the horizontal screws located in the door hinges.
Vertical loop adjustment
If it is necessary to raise or lower the product, adjust the mechanism vertically. There is an adjusting screw along the axis of the lower hinge. To adjust the entrance plastic doors, a hex screwdriver (5 mm) is useful.
By turning the tool, the door can be lifted slightly, and by turning the screwdriver in reverse side– the structure will be lowered.
How to avoid frequent adjustments?
It will not be possible to completely get rid of door adjustments, but making it less frequent is quite possible. When purchasing a double-glazed window, make sure that the fittings match the weight of the panel.
The optimal weight of the sash is considered to be 100-130 kilograms.
Sagging of the structure under its own weight can be eliminated by mounting auxiliary element fittings, which is called a sag compensator, better known as a "microlift".
Such a detail is simply necessary for the product, especially if there is a double-glazed window with impressive dimensions of the structure. And if you correctly install the support rail - the opening limiter - with your own hands, you can easily avoid jamming and sagging of the structure.
As you can see, adjusting a plastic door is not very difficult if you wish.
Sections of the article:
Adjusting plastic doors is a process that is designed to eliminate all sorts of problems that have arisen during the use of the structure. No matter how expensive the door and its components are, items always break, especially those that are used frequently.
Most often, door adjustment is required, for the reason that the hinges can weaken and become loose. As a result, the door is uneven, and a draft blows from the opened cracks. The root cause of the breakdown is the wear of individual parts, but their quality also plays a significant role. That is why you should not save on quality, so that in the future you do not have to think about adjusting the plastic door.
If you have problems with a plastic door, but you don’t want to contact the masters, you can fix the breakdown yourself. But for this you need to prepare and find out the answers to the following questions:
- Where in the door are the parts intended for adjustment located?
- What problems can generally arise with plastic doors and how to solve them;
- How exactly is a plastic door adjusted?
What is responsible for regulation?
To adjust the door, you will need a hexagon with a diameter of 4 millimeters (most often), sometimes pliers will be useful.
The first adjustment unit can be found on the bottom door hinge By turning it with a hexagon, you can raise or lower the door, depending on the direction of rotation.
A necessary tool. Here you can also find a node that moves the bottom of the door to the right or left. Sometimes the adjusting screws are covered with protective caps that are easy to find and remove. To move the top of the door to the left or right, turn the screw located at the top hinge.
The clamping force of the door against the door frame is controlled by eccentrics, which can be found throughout the door body. By twisting them, you can achieve precise adjustment of plastic doors and their tightness by changing the pressure in individual areas. In doors with a tilt-and-turn operating principle, there is a way to adjust the pressure of the entire upper part. To do this, you need to turn the screw located at the top of the door.
Getting to this screw is quite difficult; you need to put the door in both the ventilation mode and the “wide open” mode. A built-in mechanism that can be bypassed protects against such opening. You just need to open the door, align the plate that is located at the end of the door near the handle (parallel to the rubber seal) and turn the door handle to ventilation mode. This is a rather complicated procedure, so to know exactly how to adjust a plastic door in this mode, we recommend that you watch the video.
Adjustment methods for various problems
To correct deficiencies, you need to know which screw is responsible for what, and for what problems to turn it.
This is due to the complexity of the door design and the abundance of all kinds of screws, the incorrect twisting of which can lead to complete breakdown of the mechanism.
Upon request, adjusting plastic doors, you can find many videos from professional craftsmen that will help in the work.
Sagging
Over time, the input protection sags under its own weight, and due to the fact that it is mounted in the air. This is one of the most common problems and at the same time unpleasant, since in this case the lower profile rubs against the frame, and in difficult cases the door becomes difficult to close. In this case, we will definitely have to worry about adjusting the plastic door before the situation gets worse.
Warping and sagging of the door. To fix this problem, you need to lift the door up. This can be done using a special hole in the middle of the bottom loop. By inserting and turning the hexagon clockwise, we will raise the door higher. If you need to lower the door, you will have to turn it counterclockwise.
In the case where the frame only touches the part of the door opposite the hinges, horizontal adjustment of the top hinge will help. By inserting the tool into the hole and turning it clockwise, we will pull the upper section of the door closer to the frame.
Top hinge adjustment. Adjustment of plastic doors from sagging can be carried out independently, but to know the purpose of all screws and connectors, you need instructions from the manufacturer.
Friction on the box
If, when closing and opening, the door rubs against the frame, you need to know how to adjust the mechanism by moving the plastic doors to the left or right. First, we move the lower part by turning the hex key in the connector in the lower hinge, and then do the same trick with the upper one.
Bad pressure
If a draft is blowing from your door, then most likely the pressure of the door to the frame has weakened. This can be corrected by adjusting the plastic door, namely the eccentrics. The mechanism of their operation is that when closing, the eccentric climbs behind the pressure plate.
Eccentrics of a plastic door. It follows from this that to increase the pressure it is necessary to turn each of the connectors exactly the same way. You should not assume that the stronger the twist, the more reliable the clamp; with extreme pressure, the seal may dry out and stop doing its job. Craftsmen recommend loosening the pressure in the summer to give the sealing rubber a little freedom and provide a little additional ventilation in the house.
Difficult closing
Another common problem with plastic doors is that you need to apply force to close them. Most often, force is required when turning the handle.
Such symptoms indicate winter mode eccentrics, and to make closing easier, you need to loosen the screws.
Before adjusting plastic doors, you need to watch a training video to know the required tightening level.
Another reason for difficult closing may be a clogged door mechanism. In mild cases, you can get by with complete lubrication, in difficult situations you will have to disassemble the door and clean the system.
If the door is used for a long time, the handle may become loose. To correct this problem, rotate the top plate of the handle base and tighten the bolts underneath it.
Adjusting doors with GreenteQ hinge
If the door is heavy (more than 40 kg) and is often used, in most cases it is equipped with GreenteQ type hinges. Adjusting plastic doors, especially on your own, can be a problem, so before starting work it is recommended to watch a video of the process. They can be adjusted in three planes:
- Vertical;
- Horizontal;
- Press to the box.
To access the hinges, you need to remove the plastic protection from them, which is quite easy to do. To raise or lower such a door, insert the hexagon into the socket located at the bottom of the hinge and adjust by twisting to one side. Remember that the adjustment of plastic doors begins with the bottom hinge, and then the middle and top ones are adjusted to it, which can be done independently.
To move the doors left or right, screw in or out the screw located in each hinge under the decorative mask. 
To adjust the level of pressure, insert a hex key from the top end of the loop, and use circular movements to change the position of each of them. Now you know how to properly adjust displaced or weakened plastic doors using your own hands.
So, adjusting PVC doors is a simple process, but it requires care and perseverance when doing it yourself. Now you know how to adjust a plastic door without calling specialists to your home.
For the winter, you need not only to insulate windows and walls, but also think about doors, be they entrance doors or even just balconies. The article contains instructions on how to identify problems with a plastic structure without a technician and make the necessary adjustments yourself.
Main problems with balcony doors and their causes
As soon as specialists install a plastic door, they immediately adjust it. To make sure that the craftsmen did their job conscientiously, pay attention to the following points:
- The door frame is pressed tightly against the frame in all places.
- The door opens effortlessly and also closes. If it creaks, it means the work was done poorly.
- The structure is not vertically displaced. You can check this using a building level.
- The door doesn't sag. A simple test will help you check this. Taking a pencil, trace the closed canvas over the entire area, and then compare the resulting lines with the frame. If they are parallel, the adjustment work was carried out efficiently.
- If the door, opened halfway, remains motionless, it means it is adjusted correctly.
Attention! Make sure that during this check there is no draft in the room, which will cause even a well-functioning door to close on its own.
Over time, the structure wears out, and then additional corrections need to be made. Most often it is required in the following cases:
- Part of the lower shutter touches the threshold - a sign that the door is sagging under its own weight. The majority of the weight falls on the glass unit, so if it is double-glazed, the hinges become weaker and the sash moves.
- Unsteady door knob. This problem is the easiest to fix. Turn the cap at the base of the handle and tighten the screws using a screwdriver.
- The sash touches the frame in the center - this indicates that its side part is displaced. This sometimes happens due to frequent temperature changes. Doors that lead to an unglazed balcony are especially susceptible to weather conditions.
- The door pressure is loose.
Advice. If the door requires additional adjustment, contact the company that installed the door. Do the work yourself only if the warranty period for the plastic structure has expired.
How to diagnose weak clamping density
The following signs indicate that adjustment is needed:
- The canvas is not pressed very carefully to the frame. It feels like air is coming from under the seal.
- The door closes quite tightly, you need to apply more force than usual.
Attention! If this defect is not eliminated, then in winter there will be drafts throughout the apartment.
The following experiment will help determine the need for regulation:
- Take a piece of paper.
- Place it between the frame and the door frame.
- Close the door tightly.
- Pull the sheet over the edge, remembering how easy it is for you to do it.
- Repeat the procedure on all areas of the structure.
Advice. To independently adjust the mechanism of a plastic door, stock up on several types of screwdrivers, keys of different diameters with 6 edges, pliers and a set of gaskets.
Instructions for adjusting the pressure
- Adjust the tightness of the door by rotating special parts - eccentrics - with a wrench and pliers. They are located at the end of the canvas, usually in 3 places: at the top, in the center and at the bottom. You can see what these parts of the mechanism look like in a video or photo.
- Rotate each eccentric a little, checking how much the pressure has changed. So you will choose best option and adjust the density, but only in the area of the door handle.
- To ensure complete tightness of the plastic structure, make adjustments on the hinge side as well. To do this, turn every third adjusting screw both at the top and bottom. It is convenient to use a hex wrench for this purpose.
Advice. Adjust the pressure twice a year, doing it in summer and winter. When it's cold outside, make the fit tighter, and when it's warm, loosen it. It is not recommended to leave the “winter” setting for the summer, since both the seal and the mechanism door block wear out much faster.
Adjusting the door if it is sagging
To eliminate this defect, you can not remove the door leaf from the hinges:
- Having opened the doors, find a screw on the top canopy that can be opened with a hex key or a special “star” key (depending on the model of the plastic structure itself).
- Turn the screw a couple of turns to the right.
- If the sash still touches the threshold, remove the protective cap from the bottom hinge.
- Find the adjustment screw and also turn it to the right a couple of times.
If the door hits the frame in the middle, do the following:
- Use a wrench to turn the lower adjustment screw, which is located on the side, with inside. 2-3 turns are enough. This will move the sash towards the hinge.
- If the door does not close well, repeat the procedure, but this time on the upper canopy.
Horizontal adjustment. Step by step description
Sometimes it becomes necessary to adjust the position of the door, for example, move it a little to the right or left. For this:
- Open the door and remove the screws from the top hinges. Use a 6-blade screwdriver.
- After closing the door, remove the linings behind which the screws are hidden for debugging the mechanism.
- Twist them: in the top loop more tightly, in the bottom - a little looser. This way you will prevent the structure from skewing.
- If you need to move the door evenly towards the awnings or, conversely, away from them, remove the trim from the bottom hinge.
- Tighten it and slightly loosen all the screws that are located horizontally in the awnings.
Attention! By turning the screws clockwise, you will move the door towards the hinges, by turning it counterclockwise, you will slightly move the door in the opposite direction. In this way, it is possible to correct the movement of the structure within 2 mm.
Vertical adjustment. Briefing
If the door needs to be lowered or raised slightly, make vertical debugging of the mechanism.
- Locate the adjustment screw at the bottom end of the canopy. It is located along the hinge axis. Sometimes the screw is hidden by a plug that needs to be removed.
- Turn the adjusting screw to the right if the door needs to be raised, and to the left if it needs to be lowered. A hex screwdriver is again suitable for this, and the lifting height can also be adjusted up to 2 mm.
Advice. To avoid having to adjust the door so often, install an opening limiter and a microlift on it, which supports the door when it is closed and prevents sagging.
