What to rub on rubber to make it shine. Blackening and paint for rubber. Rubber blackening agents

Blackening of tires is the treatment of rubber with a certain composition that will give them a beautiful shine with a black tint.

To perform this procedure, lazy drivers buy special auto chemicals, which are not cheap, although in reality it is enough to know a couple of recipes and you can do the blackening of tires with your own hands every day, without the large expenses for this procedure.

But the most important point is that the tires must always be clean before the procedure.

Recipe with glycerin

The most common recipe for creating a tire blackener is a recipe with glycerin.

Bottles of glycerin are purchased at the pharmacy; as a rule, one container contains 25 ml of the substance, but there are also containers of 40 ml. The usual rate is 5-7 bottles. For example, let's take 5 x 25 ml.

Then take a regular spray of glass cleaner or glass cleaner and pour the contents of all five jars into it.

The first category of people prefers to experiment. Some, to make the composition fattier, make a proportion of 3/5 (three parts of water to five parts of glycerin). In this case, the composition will be fatty, but its quantity will be less.

Or vice versa, in order to increase the amount of composition, but reduce the fat content, the proportion is changed, for example, 8/5 (eight parts of water and five shares of glycerin).

Note that the numbers may vary depending on your imagination, the main thing is not to overdo it with strong concentration (read about this below) and so that the result pleases you.

There are two ways to apply the compound to tires. If the composition is greasy, then first spray it onto a sponge, and then rub the tire last.

If the composition is liquid, you can immediately spray it on the tire and then rub the surface with a sponge.

The advantage of this method.

Flaws.

There is only one – not the durability of the result obtained. The fat content of glycerin first makes the rubber shine, but then attracts dust. And after the first one, the appearance will no longer be the same. But under ideal conditions in summer, the shine and look lasts for about a week.

The composition stays on the bumper until the first rain.

You also need to understand that tires are not made of oil-resistant rubber, so large concentrations of glycerin will negatively affect the physical and chemical state of the rubber.

Therefore, it is still better not to overdo it with the concentration of glycerin, but the above proportions will not cause harm.

Laundry soap

Don’t be surprised, ordinary laundry soap can also save the situation. Take a medium-hard brush, 70% (or about this figure) laundry soap and water.

We moisten clean rubber with water, lather the brush and rub the tires with active movements.

You can go the other way, grate the soap into a container with a grater or a knife and add water there. Get the soap to dissolve. Dip the brush into the resulting solution and rub the tires.

The result will not be long in coming; the tires will be black, like new.

The advantage of this method:

1. Cheap;
2. Simple and accessible.

Flaws:

Do not use laundry soap frequently, as it dries out the rubber, reducing its service life.

Shoe polish (gloss)

Colorless gloss and black paints or shoe polish are perfect. Choose inexpensive options.

Don't forget to wash your tires and let them dry.

For application, use a sponge, any foam rubber, or a shoe brush. The result is good and the paint lasts a long time.

This method has one drawback: you can’t drive right away, the paint must dry, you’ll have to wait 10 minutes.

Silicone PMS-200

To blacken tires, you can use PMS-200 brand silicone. Everything is simple here, wash the wheels, apply silicone to the sponge and rub the tires.

Sold in all auto stores for a fair price affordable price. They allow you to give the appearance of your iron horse more aesthetics. But there are also folk remedies used to restore the former color and shine of tires. We invite you to try making it using available materials. In the article you will learn about the most popular methods, as well as get acquainted with all their pros and cons.

Most susceptible to influence during vehicle operation external factors, of course, wheels. Uneven roads, reagents, water, sun - all this leads to tires losing their rich black color and becoming faded. To return them to their former self appearance shoe polish, glycerin, silicone oil, laundry soap and even Coca-Cola are used.

Shoe shoe

When a man puts on a nice suit, the most important thing is that he has polished shoes, otherwise the whole outfit will be ruined. It’s the same with a car - faded wheels won’t add beauty. Therefore, you can use ordinary... shoe polish. Yes, the same one we use to rub our shoes. Actually, other shoe creams based on it are also suitable.

After you have applied the rubber ink from shoe polish with your own hands, you will have to wait a long time until it dries. Another disadvantage is the fact that the shine of the tires will not be that bright, unless the shoe polish contains wax. This composition washes off quite quickly and is only suitable for emergency cases, for example, before going on a holiday.

Glycerol

A homemade rubber ink made from glycerin and water is the most popular among our compatriots. It is very cheap and easy to prepare. A jar of glycerin in a pharmacy rarely costs more than ten rubles.

It must be diluted with water in a one to one ratio. The resulting solution is poured into a spray bottle and applied to the tires. If you add more glycerin than water, the tires will be blacker and shinier. This solution should be applied with a sponge. But it is worth remembering that the surface of the wheel will become fatter, which means that dust, dirt and sand will stick faster. However, you can use this method often without harming your tires. The main disadvantage of a homemade rubber dye made from glycerin is that it is easily washed off with water.

Laundry soap

Who would have thought that ordinary laundry soap could help solve this problem. It turns out it still can. You can rub the brush with it properly and treat the tires. Or make rubber ink with your own hands by grating soap into warm water and letting it dissolve into a sticky mass. Then rub the tires thoroughly with it.

After this treatment, the wheels will look like new - black as pitch and shiny in the sun. The advantages of this method include simplicity, low cost and accessibility. The downside is that soap dries out the rubber. Frequent use will lead to the formation of microcracks and the service life of the tire will be noticeably reduced.

Silicone oil

If you are wondering how to make rubber ink with your own hands, then the answer to this question is completely simple. Just buy silicone oil, and you don't have to invent anything.

A liter of the most common brand "PMS-200", which is a medium-viscosity oil, costs around 500 rubles. Yes, it turns out to be much more expensive than all the methods described above, but this volume is more than enough for at least a year.

Among the advantages of using silicone oil as a rubber dye, it is worth noting the durability of the effect of its use. It is not washed off with water at the first contact, does not attract dust and dirt, moreover, does not dry out the tires and does not lead to the formation of cracks. But it returns blackness and shine almost instantly and for a long time. Silicone perfectly resists ultraviolet radiation and other external influences, preventing the tires from drying out.

Another way

If you don’t know how to make rubber ink with your own hands, then we will tell you another way. To do this you need to arm yourself detergent for windows "Mr. Muscle" in the form of a gel and the most ordinary Coca-Cola.

This method is less popular, but also relatively effective. To do this, first you need to thoroughly wash the wheels with detergent, and only then apply soda on top using a spray bottle. The drink is sprayed onto a medium-hard brush and rubbed into the tires. The vibrant black color and sleek shine will return instantly. You need to repeat this procedure several times, each time allowing the tires to dry thoroughly. You can repeat the procedure immediately after the wheels lose their presentable appearance.

I would like to note that all folk remedies produce a short-term effect. Yes, the tires will become black and shiny, but it will all fade pretty quickly. Therefore, it is best to use professional chemicals for blackening tires, which are sold at any auto store. Moreover, their cost starts from 200 rubles, which is quite inexpensive, you can use them every day without fear of consequences.

Tire blackening agent used in caring for vehicle and giving it aesthetics. There is a wide range of similar special products on the shelves of auto chemical stores. Do-it-yourself folk ones can also serve as a good alternative to some of them.

During the operation of a car, wheels are most susceptible to the influence of external factors. The sun, water, salts, chemicals and bumps on the road are the main culprits in the aging of a tire and the loss of its original (store) appearance. Restoration using the rubber blackening method will help restore freshness and former beauty. This can be done using several mixtures, in particular: glycerin, shoe polish, soap, silicone or a specially developed liquid. To figure out the best way to blacken tires, you should weigh all the pros and cons of each treatment.

Do-it-yourself tire blackening procedure

Why blacken rubber and what will it give?

First of all, you need to understand what it is, so this is the process of treating rubber with a specially designed liquid, which does not paint it black, but enhances the blackness and covers it with a protective layer. This product not only gives more shine, but also protects the wheels well from dirt, dust, and prevents cracking. In addition, inks soften the rubber, thereby making it elastic, which helps maintain its integrity for a fairly long period.

Effect before and after treatment

Benefits of tire blackening:

1. Tire wear will be significantly reduced.
2. Protection against pollution.
3. Masking of minor defects using a layer of silicone glue.
4. Tire service life.

Inks can be purchased at any auto store, their price starts from 200 rubles, but if you decide to save your budget, you can carry out this procedure at home, so next we will deal with the most popular methods of blackening tires.

Folk remedies for blackening tires

In search of a cheap but good alternative that can give a 100% blackening effect, no matter what methods are used, not only the main components of professional products are used, but even carbonated sweet drinks, for example, Coca-Cola or Fanta.

The use of products containing sugar creates an imaginary impression of gloss. Soon they will begin to look worse than before treatment, since such a substance will strongly attract dust.

When blackening tires with your own hands, 5 folk remedies and several special ones from the section of protective auto chemicals are used with great popularity and with satisfactory efficiency.

The following tire blackening products are available::

1. Shoe polish.
2. Glycerol.
3. Laundry soap.
4. Silicone oil.
5. Using a special composition

In absolutely all cases, without exception, before carrying out the tire blackening procedure itself, it is recommended to wash the wheels.

Shoe polish - for blackening rubber

Here we can draw an analogy with boots. Any self-respecting man knows that no matter what his suit is, unkempt shoes will immediately catch your eye. And to return them to their original shine, you need to regularly use shoe polish. The situation is exactly the same with tires.

For blackening car tires at home you can use shoe polish or black shoe polish with wax. If the old shoe polish is a little dry, then to make it easier to apply, you can dissolve it a little with kerosene.

Flaw:

• does not look very aesthetically pleasing compared to other means;
• lack of shine;
• The coloring composition takes a long time to dry, so it is not recommended to go immediately after treatment; you need to wait until everything dries.

The simplicity of this method lies in the fact that such a product can be found in every home and all you need to apply it is a foam sponge. Plus, some creams, as well as when rubbing shoes, may require additional wiping with a soft rag.

Blackening tires with glycerin and water

The most common method is to use glycerin, which can be easily purchased at the pharmacy. Glycerin is a colorless, viscous and very hygroscopic liquid, miscible with water in any proportions. In order to blacken tires at home, you will need only five jars of 25 ml or three of 40 ml, the preparation method is quite simple, you just need to mix glycerin with water in a ratio of 50 to 50 (1:1).

If you need a greasy solution, then you can use 5 parts of glycerin to 3 parts of water, then you will need not to spray the liquid, as in the first case, but simply apply carefully with a pre-moistened sponge. Also, some experimental drivers use proportions such as 1:3 (high fat effect), 1:5 (light shine) or 1:7 (light matte effect), it all depends on the degree of tire burnout.

Remember that the more glycerin, the more shiny your wheels will be, but the more road dust will also stick to them.

The most important advantages of this method are:

1. Availability of materials.
2. Profitability and minimal financial costs, its cost is about 9 rubles.
3. Possibility of fast cooking.
4. Possibility of frequent use and can also be used on black plastic elements car body, for example on the bumper.

Flaws:

• the fragility of using the tire, namely drying and cracking of the rubber at low air humidity;
• after application, the rubber will have a shine, but since it is a fatty, sweetish liquid, although the tire will shine, it will literally immediately begin to attract dust;
• After the first contact with water, it is washed off.

The shiny effect can last only 2-3 days and only if there are no heavy rains, so washing the car after application is not recommended, otherwise the tires will return to their previous appearance.

When using this method, the main thing is not to overdo it with the concentration of glycerin, as it can negatively affect the physical and chemical state of the tire due to the fact that it is a fatty liquid, and tires do not like this.

Blackening rubber with laundry soap

It’s hard to imagine that such a seemingly ordinary product as laundry soap can help with tire renewal. For this method you will only need water, soap and medium-hard bristles (approximately 70%). To carry out this procedure, you must immediately clean the tire from dust and dirt, then lather the brush thickly and rub the rubber. There is also another way, for this you will need to grind the soap using a knife or grater and dissolve it in warm water. After preparing the solution, you need to rub the tires well. Both methods are quite effective, after which your wheels will shine like new. The most important advantage of this method is its accessibility, ease of execution and cheapness. There is also another side of the coin, this method not recommended for frequent use, because soap dries out the tires too much and significantly reduces their service life. So think once again before applying any liquids to the rubber, so that you don’t have to replace it later.

Silicone oil as a tire blackening agent

This method is quite common among car owners because it is easy to perform. Most often, the PMS-200 brand is used for treating tires - silicone oil, which is a medium-viscosity oil. The price for 1 liter of product, as a rule, does not exceed 450 rubles.

This method is naturally more expensive than those described above, but if you buy 1 liter, it will last you for a whole year, even with frequent use. It should also be noted that the effect after use lasts a long time, which is quite economical, with little silicone consumption. As for use, it is also used to lubricate tires that are intended for off-season storage. It is also used to lubricate door seal rubber bands or can be mixed with glycerin. Silicone, unlike other products, perfectly resists ultraviolet radiation, and also protects against drying out, dust and condensation, which is a rather impressive fact when choosing the best folk remedy for blackening tires.

Other less popular methods for blackening tires

Another way to blacken rubber at home with minimal financial outlay using detergent is to take Mister Muscle or galla(in the form of a gel), but cola, beer and other drinks(in its pure form) that people use - create sticky layer attracts dust and dirt.

So, in order to return the tires to their former appearance, you need to wash the wheels thoroughly with a glass cleaner, for example Mister Muscle or any other, and then treat them with Coca-Cola. The cola is applied from a spray bottle onto a brush (medium hardness), and then we rub the wheels with it. These steps must be repeated several times, and after the first time it is necessary to allow the liquid to dry. Half a liter of drink is enough for about 10 washes. They say that after all these manipulations the result is not bad, and the rubber is not sticky, and gets its rich black color from cola dyes. You can repeat this method as soon as the blackness begins to disappear.

The situation with dish gel is a little different. Before applying it, you need to wash the wheels well. And then, on a clean surface, apply with a small damp sponge. After processing, you will not need to cover anything else on top. When it dries, it gives a good result. So the folk way often used by car washers.

But be that as it may, it is still not possible to prepare a truly best remedy for blackening tires at home. You will be able to achieve a short jet black effect until the first rain or off-road ride. So ideal option There will be the use of specially developed compounds that can be purchased relatively inexpensively.

Which product to buy to restore shine?

When choosing a solution for treating tires, first of all, you need to pay attention to its composition. The result will depend on it. For summer you can also water based, but for winter it is better if the product is silicone. Automotive stores offer a wide range of inks and they are all divided into two kinds:

1. Shiny- these are lubricants that consist of large quantity silicone. After applying them, the tires will become shiny and their appearance more attractive. Disadvantage: they act for a short period of time; after exposure to dust or dirt, they may lose their original appearance.
2. Matte. They are used not only when processing tires, but also for the entire car. Once the rubber is coated with this type of liquid, it will take on a deep black color. The disadvantage of this type of blackening is the short lifespan after contact with water, as a result of which their appearance becomes even worse than before staining.

You can use various means for blackening tires every day, if it’s not too expensive for your wallet. But it will be much more effective to use it to achieve a specific result after understanding the properties, purpose and consequences of processing. On various forums you can often find discussions on the topic of blackening, its necessity and meaning. Having studied several such discussions, read the reviews and personal experience use, we came to the conclusion that the best means For blackening rubber, the following 5 liquids can be considered.

Blackening of wheels. Life hack against special means.

Test of Doctor Wax, Dannev, Turtle Wax and Hi-Gear products

TOP 5 means for blackening

Blackening agent black gloss

Used for processing tires special remedy, called “black gloss” (Turtle Wax), which is quite popular in car washes. The method of application is very easy to perform; you need to apply it to the side parts of the tires using a sprayer and wait about 10 minutes until it dries completely. There is no need to further wipe the tires after application. As for its cost, prices for liquids start at 480 rubles. for 1 liter.

Advantages of this tool:

• protection from dust and dirt;
• unique antistatic properties for rubber prevent the settling of dust and dry road dirt;
• due to hydrophobic properties, water and liquid dirt drain from the treated surface;
• improves the color of tires without drying them out;
• prevents cracking and discoloration of rubber; after 6 days of testing, in rainy weather the tires retained their black color.

Real tests of the Black Gloss product showed that the wheels lost their shine and began to attract dust approximately 9 days after application. At the same time, the car drove into a car wash and got caught in the rain a couple of times.

Getting the product on the tire tread is strictly not recommended! because silicone-based compounds reduce the braking efficiency of the car. It is also not advisable to allow contact with paintwork and headlights - the appearance may deteriorate.

If the product accidentally gets onto unwanted areas, you can remove it with a dry soft fabric or microfiber.

Blackening of rubber XADO Red Penguin

Regarding all the characteristics and warnings when applied to tires, you can read on the label. On our own behalf, we note that after application the wheels had a very attractive appearance. And if you compare the effectiveness of the durability of black with TURTLE WAX, then the red penguin will definitely last a little longer. By the way, the price is also slightly lower - 420 rubles. for 1 liter.

Advantages:

• rich black color;
• maintains a long-lasting effect on tires.

Conditioner-cleaner for tires HI-GEAR HG5331

The application method is quite simple; the foam needs to be evenly distributed from the can onto the tire and wait until it dries. Please note that the product can only be applied to wheels at temperatures between +15 - +25˚С. Its price varies from 446 to 530 rubles.

Advantages:

• can be applied to a wet tire;
• the presence of a polymer film after use that can repel water and dirt.

Flaws:

• it is necessary to bring the wheels to the required temperature;
• takes a very long time to dry;
• the wet shine effect that the manufacturer claims is completely absent.

Tire restorer DoctorWax

A special product created for restoring rubber. Fills microcracks and eliminates minor surface defects. Can be used not only for tires, but also for car mats. Designed to protect against the aggressive effects of salt and deicing agents.

According to customer reviews:

• Refreshes, renews and protects rubber and plastic well;
• adds shine to seals;
• has excellent water-repellent properties;
• protects rubber from the aggressive effects of salts;
• economical consumption.

From the comments it should be noted that:

• the effect is quite good, but not long-lasting;
• The bottle is not very convenient to use because the product leaks during application.
• in rainy weather, literally within 2 days after use, you can notice that the tires lose color and shine; moreover, adhering sand and dirt are noticeable on the sidewalls, which indicates a complete absence of a protective film.

If you pay attention to the cost of this product, due to the stated capabilities, it is somewhat overpriced, because it ranges from 258 - 450 rubles. for 300 ml.

Dannev color restorer

The manufacturer claims that this rubber blackening agent helps achieve a wet shine effect, but whether this is actually true still needs to be checked.

Flaws:

• the ink does not counteract ultraviolet radiation;
• there is no protective layer;
• after use, the wet shine of tires disappears very quickly;
• A few days of rain negates the wet shine effect.

Advantage: deep black color can last for 2 days in rainy weather.

The application method is also not very complicated, but caution will still be required during the work; the most important thing here is that the liquid does not get on the tread, brake disc, paintwork and headlights. As for the price, it costs about 258 rubles. for 250 ml.

After all of the above, I would like to note that as a result of the tests, the most effective means turned out to be Turtle Wax(tire color restorer). It can be used on all exterior plastic and rubber body parts. But it is better not to use it inside the cabin, as it has a strong solvent smell. The effect on tires lasts about 3 days. Regarding the ink Dannev, then taking into account minimum costs, is also worthy of attention. In third place we can place a very popular tire cleaner conditioner from HI-GEAR. Because for a not so different effect, it is not cheap. The last place in the TOP is occupied by a tire restorer Doctor Wax, because it is intended to restore rubber products to a greater extent, and not to blacken tires.

DIY rubber blackening

In order to blacken rubber with your own hands, you need to take an old used toothbrush, which will help wash everything off. hard to reach places on the tire. After cleaning the rubber, you can immediately proceed directly to the blackening process itself. You will need a spray bottle with liquid for treatment; you can prepare it yourself in advance, or buy it at a specialized auto store. During the application process, the product must be rubbed into the tire for a better effect. Then you need to wait a few minutes until the liquid dries completely, but if you applied a product that foams, then you need to wait a little longer, about 20 minutes. Well, you won’t need to do anything else, now with beautiful tires you can go conquer the roads.

And so, the plan for blackening tires with your own hands will be like this:

1. Filming upper layer dirt so that the product is better absorbed and does not collect dirt (in my opinion, it is better if you do this with some kind of detergent).
2. Let the wheel dry, and the composition is not diluted with excess water.
3. Spray the product onto the surface of the wheel. Preferably in dry, windless weather.
4. Rub with a sponge or leave it like that for a while (depending on the instructions).
5. To consolidate the effect, it is recommended not to leave for about half an hour so that the liquid is completely absorbed and dry.

When treating with special products intended for cleaning and blackening, carefully read the instructions before application! Some of them (those with a silicone base) are contraindicated for contact with the asphalt, as this impairs traction, while others can be applied to the entire wheel (for example, for storage).

To summarize, we note that...

By and large, there are 3 options for blackening rubber: the first is to do it yourself and use homemade remedy(shoe polish, glycerin or silicone oil); the second is to also do the processing yourself, but using a specially purchased composition; the third is to take the car to a detailing center, where specialists will do it for you for 300-500 rubles, following all the technology. Each of them has its own pros and cons, so decide for yourself which one is better to choose. If you look from an economic point of view, then it is worth considering only the first two, using one of the five methods. The least expensive ones are glycerin, laundry soap and cream with wax. Glycerin and laundry soap have at least some positive effect, but shoe polish with wax, although it gives the rubber a black color, is not suitable for use at all. So home remedies are not very effective, and their low cost justifies this. The most expensive and effective folk method silicone oil turned out to be used for blackening rubber, its effect is comparable to store-bought product“Black gloss.” The cost of such a product will cost 400-450 rubles, which is really enough for several treatments.

All the methods mentioned in this article have been tested in practice more than once and they really work. The most important thing is to wash and dry the rubber well before the procedure.

After a certain time, the tires on the wheels lose their color - they fade, affecting general form car. There are two ways to restore the lost shine and color to wheel tires: using blackening or rubber paint.

The process of blackening tires involves coating the tire with a special liquid - blackener. You can buy such a product at the car market or in special stores. The range of factory inks is represented by two types of blackening mixtures:

1. "Brilliant." These substances are usually made on the basis of a lubricant with a silicone composition. When applied to a tire, the surface of the rubber becomes glossy. At the same time, “shiny” products wash well and do not wash off after several washes. The disadvantage of these inks is that they heavily stain the surface. If the stain gets on the surface of the car, the body will have to be washed for a very long time. Therefore, when applying these products to rubber, safety precautions must be observed (use rubber gloves, avoid contact of substances with skin).
2. "Matte." These funds do not provide mirror surface tires, after applying the substance to the tire, but they add brightness to the color of the tire. The appearance of tires after using these blackening agents becomes bright, better than that of new tires. Disadvantages include:

• shorter lifespan than “shiny” substances: “matte” ones are easier to wash off with water;
• absorb quickly.

In addition to improving the appearance of tires, inks protect rubber from external negative influences sun rays, water, chemical reagents and so on. The protective function of these substances is possible due to the creation of a thin film on the surface of the tire.

Making your own blackeners

Using blackening or paint to restore the color of rubber requires a lot of money. To save money, many car enthusiasts make ink at home. Let's look at the most common recipes for these substances.

Use of glycerin

You can buy glycerin at the pharmacy; the substance is sold in a 25 or 40 ml bottle. To obtain an ink solution you will need from 5 to 7 bottles. Glycerin is poured into a container with a spray bottle (a container for washing glass or spraying plants, etc.). Water is poured into the same container, proportion 1:1, for example, for 6 bottles of glycerin you will need:

• 6*25=150 ml of water;
• 6*40=240 ml of water.

In the first version, the volume of the bottle with glycerin is 25 ml, in the second - 40 ml. Before applying a mixture of glycerin and water to tires, the tires are thoroughly washed and dried. The ink mixture is applied to a sponge or rag, which is used to carry out the blackening process. Advantages of using glycerin mixture:

• low cost;
• the ability to refresh the color of tires regularly;
• accessibility and speed of the denigration process; no special skills are required;
• the ability to use the specified mixture to blacken the bumper.

Disadvantages:

• under ideal operating conditions, the blackening film will last on the surface of the tire for a week;
• Even rain can wash off a blackened bumper;
• glycerin attracts dust;
• The beautiful black color of the tires will disappear after the first wash.

Laundry soap

A bar of soap with a fatty acid content of at least 70% is suitable. The process of returning lost color to tires consists of the following stages:

• Clean the surface of the tire from dirt, moisten the tire with water;
• lather laundry soap a brush with medium-hard bristles;
• rub in with a brush soap solution into the surface of the tire.

Advantages of this method:

• ease of use;
• low cost.

Disadvantages: laundry soap dries out tires greatly, reducing their service life - this blackening method should not be used regularly.

Silicone oil brand PMS-200

To blacken tires using this method, you need to apply a little silicone to a sponge and use it to rub the substance into the clean surface of the tire. Advantages:

• the effect is more long-lasting than previous methods;
• one bottle of such a stain is enough for a year with regular use;
• no harm to the tire surface.

Disadvantages: the cost of the product is slightly higher than previous methods.

Shoe polish

Using this method you can use:

• black shoe cream;
• colorless shoe shine;
• shoe polish.

Before applying the blackener, the tires are washed, then a little of the blackener is applied to a sponge or rag and the substance is rubbed into the surface of the rubber. Advantages:

• longevity of the effect obtained;
• If the substance gets on the car body, it can be washed off.

Disadvantages: you cannot use the car immediately after blackening; you need to wait until the coloring matter hardens - from 10 to 15 minutes.

Tire tuning using paint

You can restore the lost luster to your tires by using blackening or rubber paint. The second method allows you to achieve longer lasting results than the first method. In addition, painting tires allows you to tune your car and make it look original.

Please note: you need to paint the outer part of the tire, inner side the product is invisible, and working surface comes into contact with the road surface. It is possible that the outer side of the tire may not be completely painted; special inscriptions that differ in color from the color of the tire are allowed. To paint tires, it is better to use a special paint that has the following properties:

• having greater permeability to prevent abrasion of the pattern;
• having adhesion to rubber;
• providing an elastic layer after drying, otherwise when the car moves under the influence of loads on the wheel, the paint layer will crack;
• having increased wear resistance.

If you paint car tires with special paint, you can protect the rubber from external factors and thus extend the life of the tires.

The most popular paint is for rubber. white, with its help, letters and inscriptions are applied to the surface of the tires and the car acquires a retro style. Wanting to use another color scheme, it is worth considering the area to be painted, since the price of colored paint is high.

Preference should be given to rubber paints based on latex or rubber. Please note: the usual latex paints For example, walls are not suitable for painting; they will not be able to provide proper elasticity due to their low latex content.

Please note: if you want to highlight a certain inscription on a tire, you can purchase a marker filled with paint - this will greatly simplify the work.

DIY tire painting

When starting the coloring process, carry out preparatory work:

• inflate tires to operating pressure;
• Wash the surface of the tire from dirt; for this purpose, you can use soda diluted with water to a mushy state;
• degrease the surface of the tire using alcohol or solvent;
• Allow the tire to dry completely.

Required tools and materials:

• paint for rubber;
• a special brush or spray gun, you can use a marker with paint;
• masking tape;
• means for degreasing rubber surfaces;
• a napkin or sponge for wiping away stains.

When starting painting, heat the sealant a little so it adheres better to the rubber surface. If you plan to make an inscription or design on the tire, then use masking tape to get a clear line. You can paint a tire well by applying several layers of paint, about 2-3 layers. Painted rubber can be used 24 hours after applying the final coat of paint.

When applying certain lines or symbols to rubber, consider:

1. You should not make a thick line in the middle of the tire; it will visually divide the tire into two parts.
2. Drawing a thin line down the middle of the tire will make the wheel appear smaller.
3. You can visually blur the outline of the wheel and make it unclear by applying a contrasting line along the outer edge of the tire.
4. Visually makes the tire profile smaller and increases the size rims line along the inner contour of the tire.

Of the presented options for applying a line, the most advantageous are stripes along the inner kennel of the product. It should be taken into account that such tuning of low-profile tires will make the tire bead too thin: the tire will look ridiculous.

You should also avoid incorrect combinations of several colors. For example, it is not recommended to tune wheels green with red tires if the car body is gray. The best option, when the inscription matches the body color or serves as its contrast.

Conclusion

When using blackening or paint for rubber, first of all it is worth considering the benefits for tires from applying certain products to tires. For example, too frequent use Laundry soap to make tires shine will reduce the life of the tire, while glycerin and silicone substances prevent the rubber mixture from drying out.

If you want to paint tires, take into account the composition of the dyes. The wrong paint will quickly crack and make the wheels look unattractive.

Experienced car owners know how important tire care is. Chemicals on winter roads, dirt, dust, solar ultraviolet radiation - all this not only spoils the appearance, but also affects the longevity of the tires. One of the ways to neutralize the adverse effects on tires and return them to their former attractive appearance is to blacken the rubber using factory or improvised means.

Processing at a service station or car wash

Many car services and car washes offer additional services to customers. Among them is blackening of rubber. This service is relatively expensive, but the money spent is worth it. The scope of work is as follows:

• tires are thoroughly washed and dried;
• a special compound is applied to the rubber;
• The tires are completely dry.

After professional processing wheels, you can immediately hit the road by car. A persistent protective film, protecting it from the effects of road chemicals and dirt, and the wheels look as if they were just bought in a store.

Application of shoe polish

Craftsmen have come up with many ways to process rubber. One of them is popular among those who like to save money: using shoe polish. This product does a really good job of blackening and restoring the original appearance of wheels. But there are several disadvantages to this type of rubber blackening:

There is only one advantage: shoe polish (or shoe polish) can be found in every home. All you have to do is find a foam sponge and spend a few minutes processing the tires.

Application of glycerin

Glycerin is an affordable and cheap product that can be found in any pharmacy. It is often used for blackening rubber at home. To treat 4 wheels, 100 ml of glycerin and the same amount of water are enough. After mixing, the solution is sprayed onto the wheels from a spray bottle or rubbed with a soft sponge.

Home craftsmen experimentally discovered additional advantages. So, if you change the proportion of the water-glycerin solution:

• light matte appearance with 1 part glycerin and 7 parts water;
• light shine at a ratio of 1 part glycerin and 5 parts water;
• increased fat content and deeper black color with a ratio of 1 part glycerin and 3 parts water.

Given the availability of glycerin and ease of processing, the method has several significant disadvantages: at low humidity, the rubber dries out and cracks, the tire is quickly covered with dust sticking to the glycerin, and is quickly washed off with water at the first contact with it.

Using silicone oil

Most often, PMS-200 oil, which has a medium viscosity, is used for treating tires. Compared to those listed above, this rubber blackening agent is the most expensive, but the effect of its use is also the most effective. One liter of silicone oil will last for a whole year, even with frequent tire treatment. In addition to blackening rubber, it can be used for lubrication. Another argument in favor of this product is that it perfectly blocks the influence of solar ultraviolet radiation on rubber, thereby extending its service life.

Using laundry soap

Do you want to make your car more presentable for one day or one trip? Use the cheapest product - laundry soap. It is great for blackening rubber, but the effect of its use does not last long. It is not recommended to frequently treat tires with laundry soap - it noticeably dries out the rubber.

The procedure is simple and can be performed by any car owner: the wheels, previously cleaned of dirt, are soaped with a clothes brush and washed clean water. After the rubber dries, the effect will immediately manifest itself.

Factory-made blackening agents

Buying a ready-made product is not a problem - they are available for sale in any auto chemical store or in specialized departments of stores at gas stations. They are divided into two main types: glossy and matte. The former contain a lot of silicone and give the wheels a shiny look, but quickly wash off in rainy weather. The latter are suitable not only for tires, but also for any other rubber parts of the car. Their action has more of a protective effect than an aesthetic one.