MDF panels are an excellent decorative finishing material, which is characterized by high installation speed and the absence of the need for “wet” work at all stages of finishing.
The panels also have their drawbacks (for example, MDF, like any wood, is afraid of water and high humidity, less resistant to mechanical damage in comparison with synthetic materials, work to restore damage to it is associated with a number of difficulties, etc.).
Fastening MDF panels depends on the type of base and the desired result. The most common type of fastening is mechanical (on the base, a frame is often equipped with wooden or metal guides, to which MDF panels are attached using nails, screws or clamps) and chemical - using adhesive compositions.
The latter method assumes a flat monolithic base, since in this case there is no frame made of profiles or guides.
Glue for MDF - review of the best options
The most commonly used adhesives for MDF panels are:
- Liquid Nails. A universal adhesive characterized by high adhesion, resistance to corrosion and moisture. Liquid nails do not react with substrates, unlike deep-penetrating glue.
- Polyurethane (or construction) foam. Characterized by various properties such as thermal insulation, sound insulation and high adhesion.
- Universal construction adhesive. A wide group of products, divided into many segments and areas of application. For MDF panels, it is necessary to use only those adhesives that provide adhesion to the base materials (brick, concrete, plasterboard, tiles, etc.) and wood (MDF consists of fine sawdust).
The most popular adhesive for MDF panels is liquid nails (TYTAN or TITEBOND Multi).
In addition to the economic effect when choosing an adhesive, you need to take into account the specifics of working with it (time for initial fixation, final drying time, method of application, service life, necessary tool and materials, etc.).
Installation of MDF panels with glue - instructions
Let's consider the technology of installing MDF using the adhesive compositions indicated above.
Liquid Nails (similar to - universal construction adhesives). The thickness of the adhesive layer is only 3-5 mm, so the base on which the panels will be glued must be perfectly flat. Otherwise, the panels will follow all the unevenness of the walls or peel off in places where they do not fit tightly.
How to glue MDF to a wall
Therefore, before gluing MDF panels to the wall, it must be leveled.
- Degrease the surface, remove all dirt, and fill the crumbling areas with putty.
- Before starting work, you need to make sure there are no irregularities using building regulations, long level or other tool.
- The glue is applied in wave-like movements or in another way (for example, pointwise in large drops) so that it is evenly distributed over the width and length of the panel. The pitch between the adhesive strips determines the force with which the panel will adhere to the base. That is, for example, when installing in places of greatest load, the frequency of application can be increased. Usually this is 10-15 cm. If the manufacturer determines the waiting time before gluing, it is necessary to maintain the required pause.
- Using a construction bubble or laser level the launch pad is installed under the right angle(depending on the intended pattern and direction of installation). Most often used vertical installation panels. You should start from the corner.
- The glue on the first panel must have time to set to the base before installing subsequent ones (the same principle applies to other difficult junctions, for example, internal or external corners). Setting time depends on the type of glue (see instructions).
- Thanks to the tongue-and-groove connection, subsequent panels can be installed without waiting (except for the waiting time before gluing).
Corners (internal or external), as well as horizontal and vertical junctions without a tongue-and-groove connection, are covered with decorative moldings (universal MDF corners). The glue should be applied to the middle of each side of the decorative corner (so that when pressed, excess glue does not come out).
The main thing is not to damage the decorative layer of the panels.
Option 2. Polyurethane foam.
Installation technology for MDF panels using construction foam is in many ways similar to installation technology using liquid nails or universal glue, with the only difference that the error of wall unevenness using foam can be higher due to a significant increase in foam volume.
The waiting time before gluing the MDF panel to the base depends on the requirements of the foam manufacturer.
Basic installation errors
For liquid nails:
- Do not overexpose the glue before installing the panel on the base. Otherwise, adhesion will be significantly lower.
- Incorrect application of glue - MDF panels will lose their attractiveness appearance if glue gets on the decorative front surface.
- Wiping off excess glue with a heavily dampened rag may cause the decorative coating to peel off.
For polyurethane foam:
- For gluing, you should use foam with a low shrinkage coefficient and a professional tool (high-quality guns for construction foam can smoothly and strictly regulate its supply).
- If you do not wait for the first panel to set, then when subsequent panels move, the foam may collapse and not be fixed to the base.
Question - why can’t you glue MDF onto liquid nails?
Liquid nails glue is distinguished by its versatility. It is suitable for mounting a wide variety of building materials. And if “wood” is included in the list of materials to be glued, then liquid nails are not only possible, but also must be used for gluing MDF panels.
Often, ordinary people can confuse “liquid nails” glue with sealants or silicones (they are applied using the same tool, the tube is very similar to the tube of liquid nails and in the store they can be on the same shelf).
However, sealants for gluing MDF panels are not recommended, since their main purpose is to fix plumbing products and seal seams.
How to glue MDF - features of installation work
You are interested in the question of how to glue MDF. Let's consider the technology of installing MDF using liquid nails and polyurethane foam.
Go over the joints with sandpaper, then prime them and seal them with putty and glue a sickle mesh. After this, you need to thoroughly prime the entire area of the MDF wall and you can glue the wallpaper. Why don't you want to dismantle the MDF and put wallpaper on the main wall? What are these unnecessary, extra layers for? The work will not be much more, but the area will increase.
Wallpapering on MDF panels? Are you seriously? It's up to you though. And for that matter, I recommend using it better. for sealing your grooves, hard wax. Or wood putty that matches the color. In general, colored sealants will still work. It’s really difficult to match the tone with them, although you still have to cover them with wallpaper. The main thing is that your sealed recesses do not differ significantly in color from the panels themselves. Through thin wallpaper, such a difference may become noticeable over time.
Putty will not work on wood; use automotive putty for metal based on epoxy resin. This is the only way the putty will stick to the joints of the panels; plastic without an adhesive base will not hold the putty even with serpyanka - there is such a negative experience. Then sand the seams so that there are no “sinks” and you can glue the wallpaper. but it is better to take glue based on bustylate.
You have already been given advice/recommendations regarding sealing seams on MDF panels, I will add only one thing to you (actually regarding the very preparation of them for gluing). Just know that when wallpapering, your panels will have to be completely puttied to ensure good adhesion (adhesion) of the wallpaper to its surface. And don’t forget about the primer.
It is not necessary to putty completely, adhesion is simple wallpaper glue Naturally it won’t, they won’t stick wallpaper on MDF properly, but... you still need to level the surface, and for this you just need to putty the joints. And you need to glue it, for example, onto bustilate, the glue is perfect for such a case. You can use PVA glue. It is possible to use Titan, but it is very difficult to work with it over large areas.
Preparing MDF for wallpapering, what to do?
Preparing MDF for wallpapering, what to do? Go over the joints with sandpaper, then prime them and seal them with putty and glue a sickle mesh. After this you need to thoroughly
MDF panels are a finishing material consisting of wood fibers bound together with organic resins. Due to their efficiency, they have earned great popularity in repair work. This material is especially often used for finishing public institutions - offices, shops. A wall or ceiling covered in this way will look aesthetically pleasing and modern. Newest technologies made this product completely safe, which allows it to be used in almost any room. For rooms with high humidity, such as a bathroom, a series of especially durable moisture-resistant panels are produced.
MDF panels: advantages and disadvantages
Among the advantages of the finishing material:
- relatively low cost,
- variety of colors and textures,
- speed of installation,
- safety,
- high heat and sound insulation,
- practicality.
They have practically no disadvantages. The only significant drawback is the fire hazard. Therefore, manufacturers recommend laying wiring in special heat-resistant boxes.
Installation can be done in several ways. If you install the product using lathing, then no special preparation of the walls is required. In addition, communications can be hidden under the sheathing. You can simply glue the panels to the wall. We will tell you how to glue MDF panels and how to choose the right adhesive mixture.
MDF panels can also be glued to difficult areas of walls
Which glue to choose?
Typically, the manufacturer finishing materials gives recommendations on the choice of glue. Correctly selected adhesive for MDF panels is a guarantee that the product will stick firmly and will serve for a long time. Universal means do not always live up to expectations. Although there are universal adhesives that perfectly glue any materials.
Among such universals we can highlight Kleiberit 636. It applies well, dries very quickly, and can withstand significant loads. It contains synthetic resins. The German manufacturer guarantees the safety of the products.
Moment Crystal is also great for gluing wall panels, including MDF. It has high moisture resistance. Not afraid of temperature changes.
Adhesive Moment Crystal for panels
MitreFix adhesive composition is specially designed for installation of such finishing material. By using it, you can be confident in the durability and reliability of gluing.
Often, so-called liquid nails are used for gluing MDF panels. This is a universal adhesive that can withstand significant destructive loads. With their help, you can even glue materials that do not fit well with each other. Working with this composition is easy and convenient.
Before you decide which glue to use to glue MDF panels, you need to know what parameters are used to select the glue. The selection criteria for the adhesive mixture are:
- high adhesive strength,
- resistance to temperature changes,
- moisture resistance,
- no toxicity.
Operating procedure
Unlike the method of fastening panels using lathing, gluing them to the wall involves preparatory work. Here is an approximate algorithm of actions:
- You need to prepare the surface to be glued: level it, remove old wallpaper, prime the wall.
- Mark the panels using a tape measure and cut to the required dimensions.
- Apply glue to the wall or panel (depending on the type of adhesive mixture).
- Press the panel down, being careful not to damage the outer layer.
- Straighten joints if necessary.
- It is better to fill the seams with sealant. This will prevent moisture from entering and deforming the panels.
- Leave until completely dry (for a day).
Wallpapering MDF panels
If MDF panels have served you for many years and have lost their former attractiveness, it is quite possible to update them. To do this, it is not at all necessary to buy and install this finishing material again. Just paste it over old wall wallpaper.
When asked whether it is possible to glue wallpaper on MDF panels, we answer with confidence: it is possible! And not just wallpaper. Self-adhesive or even fabric will do if you have a creative approach to repairs. It is better to choose textured wallpaper, on a foam base. They will hide the joints of the panels.
Since the panels are made of wood, they instantly absorb glue. Therefore, wallpapering should occur at a fast pace. Moreover, both surfaces need to be coated. First - wallpaper, and at the last moment - panels. It is best to coat the joints with additional PVA and be sure to roll them with a rubber roller. Otherwise they may separate.
If everything is done correctly, the panels covered with wallpaper will last for many years, and they will look beautiful.
Example of wallpapering on Wall panels MDF
Glue for MDF panels: how to choose and glue
Glue for MDF panels can be selected quickly enough if you know what characteristics are required for high-quality gluing of panels to the wall. Pay attention to the composition of the glue and consult with professionals.
The main problem with voluminous and large rooms is the need to fill the wall space with some content. Additional furniture or interior items are sometimes suitable for this purpose because they absorb space. The best way out in this situation is to combine facings.
This way you will veil the bad qualities of the room and turn them into advantages. Quite a popular finishing option of this type with my own hands is a combination of panels and wallpaper.
The combination of wallpaper and panels is considered one of the very famous design techniques.
Particularly popular is the horizontal and vertical alternation of panels with trellises.
Horizontal or vertical combination of claddings
Horizontal alternation of facings.
Wall decoration with alternating vertical or horizontal stripes of wallpaper and panels is suitable for any room design.
- Areas can be highlighted by alternating plastic, wood, cork strips and different types wallpaper for finishing works. Strong vinyl or non-woven fabrics with relief are best suited for this.
- You can change stripes of both polar and colors with one shade.
- The instructions say that the ideal width of the strips should be selected based on the height of the ceiling or the length of the wall.
- Often, when work related to decorating a corridor with panels and trellises or another room is performed, they are separated from each other by borders, friezes, and moldings. They not only hide the connections, but also serve as decorative elements.
Using inserts
The photo shows the method of connecting facings using inserts.
- At the very beginning, the walls are prepared.
- Afterwards they are glued with wallpaper or covered with panels.
- Next, the joining cladding is installed on the areas left in advance.
- Inserts can be sections of canvases or planks of various shapes and sizes.
- A similar design involves decorating the inserted components with borders, thin slats or moldings.
Large volume wallpaper inserts
This method is optimal for finishing work of different semantic areas of one room, i.e. its division.
- For example, a children's room is divided into sleeping, play and study areas. Place panels next to the bed and work table instead of wallpaper (calm shades), and cover the play area with brightly colored canvases. This kind of semantic load will give the baby the opportunity to concentrate where necessary or show his emotionality and dynamics.
- In a reception room, a great option is to mark a wall or niche with a TV with contrasting panels or trellises.
- IN sleeping area The most beautiful thing to note is the head of the bed. Perfect option To do this, combine panels and wall planks that have different shades of the same color.
Using flaps
Patchwork technique of combining different coatings.
- This unusual way select combinations of coatings if you want to make original interior in room.
- Here your imagination is not limited; you can cut and glue pieces of panels of different sizes, colors, textures and shapes onto the panels.
- With all this, you can organize the flaps into some patterns or paste them abstractly and chaotically.
Worth paying attention!
You must always remember, before gluing trellises onto panels made of plastic, that the planks must be finished and primed in advance.
Only then will the materials be consistent with each other.
Emphasis on projections, niches and structures
When your home has a complex configuration (protrusions, niches, crossbars, etc.), you should not consider it a disadvantage of the house. A similar design can be done as a plus. Moreover, the cost of a similar change will be small.
You can furnish a complex room shape by highlighting original plots from its total volume. So the room will appear in a completely different form. You can cover, for example, the walls with planks, and cover the niches with canvases that contrast with them in color.
Wallpapering the panel
The question often arises when combining claddings: is it possible to stick wallpaper on MDF panels or plastic, wood and other analogues. Let's find out.
Analogs from wood processing products
ISOTEX panels are already covered with trellises or textiles, which can be re-glued if necessary.
Nowadays, in many large construction stores, purchase decorative panels made from wood processing products, for example, Finnish “ISOTEX”.
- They consist of ground pine needles. The particles of the material are held together due to its pressing at high temperatures. In other words, it does not have “chemistry” - resins, glue, etc.
- Similar panels have good sound and heat insulation qualities.
- Their width is 58 or 60 cm, height 2.7 or 2.55 m, thickness - 12 mm.
- We now produce a large selection of panels of various colors and textures..
Worth paying attention!
Innovative production technology makes it possible to produce lightweight, porous panels, which at the same time have good density.
This provides the opportunity to stick acoustic panels or textiles onto similar wallpaper.
Moreover, canvases can be used in different varieties - paper, vinyl, fiberglass, etc.
How to glue canvases to vinyl planks
PVC panels must be finished with an abrasive sponge before gluing wallpaper.
Is it possible to stick wallpaper on PVC panels? Yes, this can usually be the case. But the base must first be sanded and primed.
You will need an abrasive pad (Scotch Brite), plastic primer, white spirit and an adhesive primer.
- First, matte the plastic coating with Scotch Brite..
- Next, remove any dust that appears from it..
- Then apply two primer coats for plastic..
- Loosen the adhesive primer mixture with solvent and cover the panels with it using a paint roller or brush.
- When the soil dries, the question of whether it is possible to stick wallpaper on panels made of plastic will be resolved. Do it with courage.
SIP panels and Liquid wallpaper
Liquid wallpaper fits perfectly on SIP panels.
- Liquid wallpaper is considered a very popular type of cladding. They have good decorative and sound insulation properties.
- They perfectly hide small and medium-sized wall irregularities.
- One more thing good quality coating is that it can stretch without changing the structure. This property indispensable if the cladding is carried out in a brand new house that has not undergone final shrinkage.
It is quite convenient to apply liquid wallpaper on SIP panels, because... the walls are completely perfect. If you use them in a kitchen area or a room with a bathroom, then cover the cladding with a non-colored varnish so that it does not absorb moisture, grease and dirt.
Conclusion
Combination different materials It is considered a very popular type of cladding. This kind of combination increases the possibilities of decorating rooms and makes it possible to hide their bad qualities.
The video in this post will illustrate the topic.
The main problem of large and tall rooms is the need to fill the wall space with some content. Additional furniture or interior items are not always suitable for this, as they eat up space. The best way out in this situation is to combine finishes.
This way you will disguise the shortcomings of the room and turn them into advantages. The most popular way to do this type of finishing yourself is to combine panels and wallpaper.
Combination methods
The most common is vertical and horizontal alternation of wallpaper panels.
Horizontal or vertical combination of finishes
Wall decoration with alternating vertical or horizontal stripes of wallpaper and panels is suitable for any room design.
- Areas can be highlighted by alternating plastic, wood, cork strips and various types. Thick vinyl or non-woven fabrics with relief are best suited for this.
- You can alternate stripes of both contrasting and solid colors.
- The instructions indicate that the optimal width of the strips should be selected based on the height of the ceiling or the length of the wall.
- Often, when finishing a corridor with panels and wallpaper or another room, they are separated from each other by borders, friezes, and moldings. They not only mask joints, but also serve as decorative elements.
Application of inserts
- First the walls are prepared.
- Then they are covered with wallpaper or covered with panels.
- Next, a compatible finish is installed on the pre-left areas.
- Inserts can be sections of panels or strips of various shapes and sizes.
- This design involves decorating the inserted elements with borders, thin slats or moldings.
Wallpaper inserts on large volumes
This method is optimal for finishing different semantic areas of the same room, i.e. its zoning.
- For example, a children's room is divided into sleeping, play and study areas. Install panels near the bed and desktop instead of wallpaper (calm colors), and cover the play area with canvases of bright colors. Such a semantic load will allow the child to concentrate where necessary or show his dynamics and emotionality.
- In the living room a good option– highlight a wall or a niche with a TV with contrasting panels or wallpaper.
- In the sleeping area, it is best to highlight the head of the bed. The best way to do this is to combine canvases and wall planks that have different tones of the same color.
Application of flaps
- Choose this original method of combining coatings if you want to create unusual design premises.
- Here your imagination is not limited, you can cut and glue pieces of canvas onto panels different sizes, colors, textures and shapes.
- At the same time, you can organize the flaps into some patterns or glue them abstractly and chaotically.
Note!
Don't forget, before you stick the wallpaper on plastic panels that the planks must be pre-treated and primed.
Only then will the materials be combined with each other.
Emphasis on projections, niches and structures
When your home has a complex configuration (protrusions, niches, crossbars, etc.), you should not consider it a disadvantage of the house. Such a design can be made advantageous. Moreover, the cost of such a change will be small.
You can play with the complex shape of the room by highlighting non-standard areas from its total volume. So the room will appear in a completely different form. You can, for example, cover the walls with planks, and cover the niches with panels that contrast in color.
Wallpaper sticker on the panel
When combining finishes, the question often arises: is it possible to glue wallpaper onto MDF panels or plastic, wooden, etc. analogues. Let's figure it out.
Analogues from woodworking products
On this moment in many large construction stores You can purchase decorative panels from woodworking products, for example Finnish ISOTEX.
- They consist of ground wood conifers . Particles of material are held together due to its pressing during high temperature. In other words, it does not contain “chemicals” - resins, glue, etc.
- Such panels have excellent heat and sound insulation qualities.
- Their width is 58 or 60 cm, height 2.7 or 2.55 m, thickness - 12 mm.
- Currently, a wide range of panels of various colors and textures are produced..
Note!
Innovative production technology makes it possible to produce lightweight, porous slabs that at the same time have good density.
This makes it possible to glue wallpaper or textiles to such acoustic panels.
Moreover, panels can be used in any variety - paper, vinyl, fiberglass, etc.
How to glue panels to vinyl planks
Is it possible to glue wallpaper on PVC panels? Yes, it's quite possible. But the base must first be sanded and primed.
You will need an abrasive pad (Scotch Brite), plastic primer, white spirit and an adhesive primer.
- Matte first plastic covering scotch-brite.
- Next, remove any dust that has formed..
- Then apply two.
- Dilute the adhesive primer with a solvent and coat the panels with it using.
- When the soil dries, the question of whether it is possible to glue wallpaper onto plastic panels will be resolved. Do it with confidence.
Liquid wallpaper and SIP panels
- Liquid wallpaper is a fairly popular type of finishing. They have excellent decorative and soundproofing qualities.
- They mask small and medium-sized wall irregularities well.
- Another important advantage of the coating is that it can stretch without changing the structure. This property is indispensable if finishing is carried out in a new house that has not undergone final shrinkage.
Applying liquid wallpaper to SIP panels is very convenient, because... The walls are absolutely smooth. If you use them in the kitchen or bathroom, then coat the finish with a clear varnish so that it does not absorb moisture, grease and dirt.
Conclusion
Combination various materials is a fairly popular type of finish. This combination expands the possibilities of decorating premises and allows you to hide their shortcomings.
The video in this article will illustrate the topic.
Often when interior decoration premises, we are forced to resort to the use of several types of finishing materials at once. In some cases, this can be explained by the design conditions and features that are inherent in a given room or apartment, and based on which we must make certain decisions on interior design. Very often, one of the optimal solutions is the use of combined types of finishing, when several decorative materials are used at once.
This approach makes it possible to focus on the obvious advantages, while hiding, at the same time, some of the disadvantages of both the room itself and each of the finishing materials. Today, one of the most popular solutions is a combination of wallpaper and panels: plastic, PVC, wood, MDF, SIP and others. By the way, this method has shown itself to be excellent when working in both residential and non-residential premises with high ceilings.
How to glue wallpaper on panels?
Many people wonder: is it possible to glue wallpaper to panels? Plastic (PVC), wood, MDF and others. In fact, to answer this question, you need to know some details about the use of this decorative material.
Please note that the market for construction and finishing materials offers a wide variety of different types of decorative wall panels.
Let's look at the most popular of them, and see if wallpapering on such surfaces is possible, and how to glue them correctly.
Pasting wallpaper onto PVC trim
A prerequisite for such gluing is preliminary preparation working surface. Therefore, answering the question of whether it is possible to glue wallpaper on PVC plastic panels, we should say: yes, it is possible. However, it is necessary to remember that certain conditions must be met. So, what tools will you need and what is the sequence of your actions? Let's get a look:
- Prepare a primer for plastic and vinyl surfaces, a solvent or its equivalent, sandpaper with fine grain or its analogues.
- First of all, treat the glossy surface, making it matte so that the wallpaper can stick to it, and wipe off all the fine dust.
- If possible, wipe the surface of the plastic with a slightly damp cloth and wait until it dries. It does not take a lot of time.
- Then you need to apply a primer designed for working with PVC and similar plastic-based materials.
- The next stage of work: surface treatment using a special adhesive primer diluted with white spirit. This is done using appropriate tools.
- After this, you can start gluing yourself and no longer worry about the question of whether it is possible to hang wallpaper on PVC plastic panels. The answer is of course positive: yes, it is possible!
Working with surfaces on wooden and combined bases
It should be remembered that today a huge number decorative panels, which can be bought in specialized stores, as well as construction supermarkets in Russia and the CIS countries, are made on the basis of wood, or a combination of wooden raw materials and other materials and elements, incl. fastening. At the same time, it is possible to mention not only wooden panels, but also the so-called SIP wall panels (OSB on both sides with a layer of insulation in the middle), which are used for the construction of prefabricated housing.
A design feature of many of these materials is that their production may not use any special fastening materials, such as glue or resin. Bonding of wood chips is made possible by the use of strong compression at elevated temperatures, as well as a special level of humidity. Thanks to an innovative approach to production, such materials are well known for their excellent performance characteristics.
Wallpaper can be glued to this type of panel, and the work itself does not differ in any special features compared to traditional ones. wooden surfaces. Proceed by analogy. By the way, you can first familiarize yourself with articles about this or similar surfaces.
At the same time, “liquid wallpaper”, which has already become popular, is often used to decorate SIP panels. What you need to know about their use:
- They have excellent performance characteristics and look beautiful.
- They are capable of hiding some minor imperfections of the wall on which they are applied.
- They are somewhat elastic. In other words, they are able to stretch a little, which is especially important when renovating new buildings.
- They are easy to install: even a non-professional can handle their application, subject to the instructions and recommendations.
Therefore, installation liquid wallpaper on decorative surfaces, as well as on SIP panels - quite simple. At the same time, you should remember that if you intend to use them in a room with a high level of moisture (when finishing a kitchen, bathroom, etc.), it is advisable to apply an additional protective layer of special varnish.
How to combine correctly
Well, now is the time to understand the features of using various combined materials. Let us dwell on the main options that are most widely used in finishing modern apartments and country houses.
Using Fragments
To do this, you need to make an initial sketch in which ideas for interior design are recorded. After this, you will need to be well prepared work surface walls, followed by the standard pasting procedure. However, that's not all. After the walls have been glued, panel inserts are installed in some areas instead of wallpaper, thus forming unique fragments.
Advice from the designer! The edging of such inserts can be made using separate decorative elements, such as moldings.
Combinations using room dimensions
If your room has sufficient height or width, it can serve as a place for such a design technique as horizontal or vertical combination of wallpaper and panels. Thanks to its versatility, this approach is perfect for any interior style. One of the most common techniques is alternation various surfaces with wallpaper. So, you can use plastic panels, then wood, then wallpaper, then PVC again and so on. A kind of circle is formed.
In addition, you can combine not only different kinds finishes, but also different colors. Concerning the right choice shades - then for this it is advisable to use special color compatibility tables. About the same as those used. In any case, with various examples You can see the use of combinations in numerous photos presented in this article. Experiment and don’t be afraid to glue wallpaper on panels, as you can see from of this material. As for various options combinations, they can only be limited by your imagination. Happy renovation!
