How to quickly remove old vinyl wallpaper from walls. How to remove old wallpaper yourself? How to peel off paper-backed vinyl wallpaper

Classic paper and washable vinyl wallpapers fit into any interior. The finishing material is inexpensive and looks good on the walls and ceiling. Fills rooms with comfort and creates a unique atmosphere. But when it comes time to update the renovation, wallpaper makes apartment owners nervous. Both paper and vinyl varieties are firmly glued to plaster or concrete surface. How to save time and quickly clean walls?

Preparatory stage

It is impossible to remove the finishing material without dust and crumbling plaster. Furniture from the premises where renovations will take place is moved to spare rooms or placed on the balcony. Massive cabinets, sofas and other objects are moved to the center and covered plastic film. The floor is covered with old newspapers, and the baseboards are sealed with wide construction tape.

It is advisable to turn off the power to the apartment. Hiding under the wallpaper electric wires, which are easy to touch with a spatula or wet, provoking a short circuit.

You can’t do without a stable stepladder, comfortable old shoes and clothes that you don’t mind getting dirty. A drill with a sanding attachment, sandpaper, and a bucket will come in handy warm water and glue packaging.

Spatula and kitchen knife

WITH finishing coating, which is more than 6-7 years old, tools with a sharp blade can handle it. Old wallpaper separates from the walls on its own due to dampness and time. It is necessary to find swollen areas, pry off peeled paper kitchen knife or the edge of a spatula, and then slowly pull. Paper varieties become dilapidated, so they cannot be jerked sharply. Pieces that have eaten into the plaster are pryed off with a wide spatula. Islands that could not be separated from the base are treated with water or a grinder.

Vinyl and non-woven options are easier to remove. A canvas with a water-repellent coating is cut in the middle and pry off the edges with a spatula. The lower half is pulled by hand, then the upper half is removed, and the remnants of the paper base are brushed off with a stiff-bristled brush.

Attention: Do not rub the plaster too hard or concrete wall, especially in old houses and apartments. The material crumbles and falls off, leaving holes and dents. You have to spend extra time and money on priming and leveling the walls for new wallpaper.

Water treatments

Fresh finishing fabric, which is up to 4–5 years old, is pre-soaked. The liquid dissolves the glue and softens the paper, protecting the plaster from destruction. Warm or hot water will do.

Wallpaper with a water-repellent coating is treated with a roller with sharp spikes. If you don’t have such a tool at home, a regular knife will come in handy. Using a sharp blade, make wide cuts around the entire perimeter. The more holes, the easier it is for liquid to seep into the paper layer.

Special solutions can handle wallpaper that ordinary water could not soften. The canvas glued to the wall using PVA is treated with laundry soap. The detergent bar is crushed and poured into a pan. Pour in 3–4 liters of water and, stirring, bring to a boil. A roller or foam sponge is moistened in the hot workpiece. Soak the finishing material in the liquid and wait 20 minutes for the soap to take effect.

Fabrics with water-repellent properties are impregnated with a solution prepared from fabric softener. Add 200–300 ml of the chemical component to a bucket of liquid. The concentration increases if there are several layers on the wall finishing material.

Construction adhesive and PVA will dissolve table vinegar. Connect the bucket hot water and 400 ml of product. Add shavings from laundry soap, if the plaster is very crumbly, and the wallpaper is literally ingrained into the base.

The solution is applied to 1.5–2 square meters. m. finishing material. You cannot treat the entire room at once, because part of the room will dry out, and you will have to repeat the impregnation to clean the walls of wallpaper. Water softens the paper base of rolls in 20 minutes, solutions work twice as fast.

Apply the liquid product with a paint roller, soft cloth or large foam sponge. Wallpaper in old houses is sprayed with a spray bottle so that less liquid gets on the walls. If you apply too much water, it can soften the plaster and putty.

The moistened canvases are pryed with a spatula with a wide blade. The remaining pieces are sprayed with a spray bottle and cleaned off sandpaper with a water-repellent coating or wire brush. Choose varieties with stiff bristles.

The remains of wallpaper and plaster are immediately swept into a heap so as not to trample dirt into the floor. Walls treated soap solution, it is advisable to wipe with a sponge dipped in clean warm water. The liquid will remove any remaining powder and fabric softener. Household chemicals absorbed into concrete base and interacts with the glue, worsening its properties. New wallpaper will not adhere well and may swell and fall off on the first day.

Steam cleaning

High-quality glue that could not be dissolved with water is steamed with an iron. You will need a sheet or thin towel, a bucket of water and an assistant to hold the fabric:

1. The rag is dipped into a container with liquid, twisted and applied to the wall, covering pieces of finishing material.
2. The iron is turned on and set to the maximum temperature.
3. Iron the sheet several times with a hot device.
4. The rag is removed and the remaining wallpaper is quickly removed with a spatula.

The paper web is softened with a steam generator or steam cleaner. Household varieties will be useful on the farm. Devices remove dirt from outerwear And upholstered furniture. Construction steam generators have limited functions, so such equipment is purchased by renovation professionals.

Use a steam cleaner to iron the wall, placing a clean, dry sheet under the device. If you do not use a rag, dust and dirt will get into the equipment, which can cause breakdowns.

Paper wallpapers are easier to work with. Ironed it and took it off. If you are going to steam vinyl or non-woven varieties, it is recommended to first remove the water-repellent film and then turn on the iron. Paper particles that cannot be removed in this way are scraped off with coarse sandpaper or a spatula.

Hot steam penetrates the putty, so the cleaned walls are dried for several days, and then primed and painted or new wallpaper is glued. If a finishing material is applied to a wet base, mold will appear.

Special formulations

People who don't have time to scrape and steam are advised to buy an instant wallpaper remover. The product is sold in construction stores. Usually it is a powder or thick jelly that needs to be diluted with water. The most popular are Atlas Alpan and Quelyd Dissoucol.

In a solution prepared from a powder, the roller is moistened and the wallpaper is treated. Small incisions are made on canvases with a water-repellent coating. The product will need 2-3 hours to dissolve the glue and soften the paper layer. The wallpaper will begin to lag behind the concrete base on its own. Cloths pry off with a spatula or hands and rip off the wall.

Manufacturers claim that the solvents are safe and do not emit toxic fumes, but it is better to work with rubber gloves. Make sure that the product does not come into contact with exposed skin and mucous membranes.

Wallpaper pasted in several layers is treated with a special solution. Not only powder, but also glue is added to the water so that the mass becomes thick, like jelly. This product is better absorbed and softens all paper bases.

Unusual options

Liquid wallpaper is one of the best inventions of mankind. The finishing material does not need to be scraped or torn off. The walls are sprayed hot water and wait 2 hours. Wallpaper gradually absorbs moisture and swells. Some areas fall off on their own, others can be easily removed with a wide spatula.

Glass wallpaper cannot be removed without special removers. The finishing material is treated with the solution and left for several hours. When the canvases swell, arm yourself with a spatula or kitchen knife and clean the wallpaper from the walls. After the procedure, the concrete base is dried, puttied and primed.

Non-woven and vinyl wallpapers do not have to be completely removed. They only rip off upper layer with water-repellent properties. The paper bottom is left if the walls are smooth, without cracks or holes. New canvases are glued on top of the old wallpaper.

Drywall

Concrete walls are not afraid of water and sanding machines. Plasterboard partitions covered with a paper layer. You cannot remove it, otherwise you will have to throw away the old slabs and buy new finishing material.

Cheap construction adhesive will help remove wallpaper from the plasterboard base. Several packages of powder are diluted with warm water. Stir to avoid lumps and apply a thick mixture to paper or vinyl sheets. Leave for 3-4 hours. The product dries slowly, absorbing into the wallpaper. They swell and get wet, so they are easily separated from the drywall.

The glue should be thick so that it does not spread all over the wall. The solution is applied in a thin layer, otherwise it will be absorbed into the drywall. Sometimes a little primer is added to the workpiece. The product will make the wallpaper dissolving liquid viscous. The solution will dry more slowly, plus the primer will prepare the plasterboard walls for further repair work.

If there is old wallpaper from grandma's time in the closet, do not throw away the rolls. The canvases are cut and glued to walls treated with glue and primer. Old wallpaper softens and sticks to the top layer. You just need to pull the edge of the canvas and the walls will become clean. You don't have to take out a spatula and turn on the drill.

In apartments built in the 50s or 60s, it is recommended to remove only the top layer of wallpaper. Let the rest stay. The walls in old apartments are thin and uneven, so light redecorating may turn into large-scale construction work.

Thin paper sheets that could not be peeled off with water and special solvents are cleaned with a drill. A brush with iron bristles is put on the tool and the concrete base is polished. Irregularities remaining after removing the wallpaper are recommended to be sealed with acrylic putty. It is inexpensive and high quality, suitable for leveling walls. The putty is applied with a stiff spatula made of of stainless steel so that it lies flat on the base.

Plasterboard boards will have to be replaced if the wallpaper is glued with PVA. In this case, neither a solvent, nor a sharp spatula, nor a drill with a grinding attachment will help.

Modern washable wallpaper is easy to apply and remove. With old paper varieties you will have to tinker, but solvent and sandpaper will solve the problem. The main thing is not to forget to dry and prime the walls after removing the finishing material, so that the new wallpaper fits well and lasts for many years.

Video: how to remove old wallpaper correctly and quickly

Vinyl wallpapers became popular in our country not so long ago, and therefore those who decide to purchase them have a lot of questions.

One of the most frequently asked questions is how to properly remove this type of wallpaper from walls. This procedure is not particularly complicated, so it will not take you too much time, but you need to know all the nuances and rules.

Perhaps this is the reason why they are so popular. It is also worth saying that vinyl wallpapers have two types of bases:

1. paper;
2. non-woven (how right?).

Depending on the basis, the method of wallpaper removal will be selected.. There are also several types of coatings:

• hard;
• smooth;
• silkscreen printing;
• foamed vinyl.

Features of removing old coating

Attention

In order for the new layer of wallpaper to look attractive and lay down smoothly and evenly, it is necessary to remove the old coating correctly.

Read about how to quickly and easily tear off old wallpaper.

To do this, you need to figure out how best to remove vinyl wallpaper. You need to remember just a few basic rules that must be followed, and in this case this procedure will go quickly and at the same time very effectively.

In order for things to go smoothly, there are some things you need to do. preparatory work, which will need to be done a day before the event.

1. For your own comfort, it is recommended to take out all large furniture from the room and, if possible, even a small one. By freeing the room from all parts, you will provide yourself with a sufficient amount of free territory.
2. The floor in the room can be covered with improvised means. First of all, this will prevent contamination, as well as sliding on the floor surface, which in turn will prevent injuries.
3. Prepare in advance the equipment you will need to remove wallpaper from the walls. To do this you will need:
   • a roller that has many spikes on its surface;
   • water bucket;
   • putty knife;
   • ladder;
   • gloves.
4. The bucket will need to be filled with warm water. In order for the removal procedure to take place as quickly as possible, you need to add a little detergent to the liquid.

How to quickly carry out the procedure depending on the types of foundation?

Proper removal of wallpaper from walls begins with the fact that you must decide on what basis it is made. The removal method will depend on the type of base. Having decided on this issue and prepared all the necessary equipment, you can proceed to the next important step.

You will need to turn off the power to the room in order for the removal procedure to be as safe as possible for you. After this, you can start removing the wallpaper, but you will also need to decide which method you want to carry out this procedure. There are many varieties, so after reading about them, you can choose the one that suits you best.

Non-woven base

If the walls of your room are covered with non-woven wallpaper, then removing them will be very quick and without much difficulty. In order for you to have the opportunity, you will only need to remove the top coating of the old ones.

To do this, it is best to use a roller that has spikes. They can easily walk along the surface of the walls, which will allow you to easily and quickly get rid of the top coating.

Having removed this layer, you can immediately begin gluing new wallpaper. This will additionally protect your wall from fungus and mold, and will also act as a protective barrier against liquids.

Experts recommend moistening the wallpaper layer with a small amount of liquid.. This will help them soften somewhat and make them very easy to remove yourself, without using any auxiliary materials. In this case, the old wallpaper will peel off in one large piece; this is ensured due to its dense material, which does not allow the wallpaper to crumble.

We invite you to watch a video on how to remove wallpaper from non-woven walls:

Paper based

If you start removing paper vinyl wallpaper, you can resort to many methods. They are quite easy and quick to remove:

1. You can use a regular spatula. Surely, every owner has such a tool and does not even need to purchase it. Quite often this method is used in cases where the wallpaper was glued to an existing layer of paper.

   Thanks to a large number paper covering, a spatula will easily remove it, especially if the walls were previously wetted with liquid. This will allow the old wallpaper to soften and subsequently peel off in large pieces.

2. The second method is to use a spiked roller at the first stage, and then wet the second layer of wallpaper with liquid. The roller will allow you to quickly remove the top layer of vinyl wallpaper, which is impenetrable. For your convenience, it is better to start this procedure from the bottom or top, but not from the middle of the wall.
3. Another option is that instead of liquid, you can use special means for removing vinyl. You can find it in any hardware store at a fairly reasonable price.

   But remember that even in this case, you will need to remove the top layer of old wallpaper using a spiked roller, as it is impenetrable. If you do not remove this layer first, the products simply will not get to the required place and will not have an effect.

4. Immediately both layers can be easily and quickly removed with special device, which releases hot air - a steam generator. If you have such a remedy, then the removal procedure will go through quite quickly for you.

From plasterboard walls

It is best to use special tools that are designed for. You can also use water, but remember that only a very small amount of it can be applied to the surface of the wallpaper.

The removal technique is almost the same as for removal. regular wallpaper . But it is also worth noting that using a spatula is not recommended, as it can easily damage a smooth and delicate plasterboard wall. Remember that all your actions when performing this procedure must be performed very carefully and slowly.

Experts recommend carefully reading all the rules that provide information on how to properly remove wallpaper and carefully following them (from the walls?). You need to act especially carefully in cases where your walls are made of plasterboard.

1. Do not wet the entire area of ​​the room with water at once, do it gradually.
2. Try not to apply too much liquid to the walls.
3. If you are afraid that you will not be able to cope with the removal, then you can purchase a special liquid for this procedure and be sure that everything will work out with it.

To summarize, it is worth saying that Removing vinyl wallpaper is a simple procedure, the main thing is not to rush anywhere and follow all the rules. In this case, everything will go quickly, and you won’t have to put too much effort into it.

In contact with

When re-gluing, you should very carefully remove old layer wallpaper without leaving even small fragments. It is this clean surface that will allow you to stick a new layer without bulges or bumps.

In 90% of cases it is enough to use the most in a simple way removing wallpaper, and we will talk about it further, but if you are among the 10% of the “lucky” ones and the sweat is already flowing in a stream, and your nerves have begun to fray - scroll down the article, there we will talk about emergency situations.

The easiest and fastest way

1. Empty the room of all furniture or arrange it in the center of the room and cover it with cellophane or newspapers.
2. For safety reasons, turn off the electricity in the apartment. Cover outlets and switches with masking tape to keep dirt out. And now the dirt will appear, believe me.
3. Prepare the following tools and materials:

• a bucket of hot or warm water;
• wide roller (can be old);
• narrow and wide spatulas;
• stopwatch.

1. With a wet roller, dampen 2-3 strips of wallpaper from top to bottom. Please do not flood the neighbors - pouring water excessively is not necessary.
2. Time it for 20 minutes. During this time, the material and glue will absorb enough moisture.
3. With a spatula, pry off the corner of the wallpaper and separate it from the wall. Clean up small pieces with a spatula.

1. Go back to step 4 and say goodbye to all the remaining canvases.

To clean the walls of a room with an area of ​​20 square meters it may take two hours. More time may be needed in cases where old paper wallpaper glued in good faith, and even worse, with PVA glue. It will also take longer to process materials with a water-repellent layer, such as vinyl wallpaper.

Tip: Cleaned walls must dry. At least a couple of hours. Only then proceed with the new finishing.

Life hacks and folk remedies

To make the process of removing wallpaper even faster and even more effective, read what additional magical tools you have at hand. It's time for them to bring real benefit to humanity.

Difficult cases at work

What to do if you get vinyl or non-woven wallpaper

We proceed as we described above, using the method of exposure to moisture, but before water procedures use a sharp knife or wallpaper tiger (most importantly, something sharp) along the old wallpaper and make cuts. Water will penetrate under vinyl film into paper and it will not be difficult for you to finish your work on time.

What to do if old wallpaper is glued to drywall

Drywall consists (attention!) of gypsum and cardboard. For obvious reasons, the last of the components cannot be wetted with water. Therefore, in this case, it is best to either carefully use a spatula, or, in as a last resort, buy a special solution for removing wallpaper.

What to do if the wallpaper is glued with PVA glue

Brace yourself. This is the most difficult case. Jewelry work. Water, even mixed with diamonds, will not help you. Take a sharp spatula and, forgetting about your plans for the whole evening, clean off centimeter by centimeter. Or ask your neighbors for a grinder (grinder) and buy an attachment with stiff bristles - the process will go faster.

Watch this video - the need for invention is cunning:

If the old wallpaper is still on the wall

Guys, let's be honest, if you have read the article up to this point and the old floral wallpaper is still intact on your wall - either you are doing something wrong and it is better to read the article slowly from the very beginning, or - you know what - leave this idea . If, with such inhuman efforts, you still failed to separate the paper and the stone now, then, believe me, they will never separate again, and under no circumstances.

Vinyl wallpaper is a very popular option for indoor wall decoration today. But time passes, and the old coating loses its attractive appearance. In this case, it is necessary to carry out repairs and remove old paintings from the walls. And here the fun begins, because removing such canvases is not so easy.

If everything is done correctly, there are no difficulties in removing old wall coverings

But don’t be upset, because there are many ways that allow you to tear off the coating from the wall quickly and efficiently. At the same time, improvised materials are used for such events. Let's take a closer look at how to remove vinyl wallpaper from a wall surface.

Preparatory stage

When you need to remove old wallpaper from a wall surface, you need to clean the room. To do this, take out the furniture if possible or just cover it. protective film to protect from dirt. You can also protect the floor by covering it with the same film. When leaving the room, it would be a good idea to place a damp cloth so that all the dust settles on it and does not spread throughout the house.

Protective film can be found in hardware stores.

It is imperative to ensure that the electricity is turned off, and all those present lighting on the wall needs to be removed. You can quickly and efficiently remove old material from the wall provided that you have prepared the following tools:

• Roller with built-in spikes.
• Container with warm water. If placed in liquid detergent, this guarantees easier removal of the wallpaper.
• Foam sponge.
• Putty knife.
• Masking tape that is applied to all sockets present.
• Gloves.
• Ladder.

A needle roller will help when working with old wallpaper

The list of these materials is approximate, because for different cases You may need various items, in some places you will be able to peel off the wallpaper easily and quickly, but in others you will have to make every effort to tear the covering off the wall.

Methods for removing old paintings

Related article: How to make a heated floor in the bathroom from heating in an apartment

Remove regular wallpaper from paper based not difficult. To do this, you just need to moisten their surface with warm water, wait a while until the liquid thoroughly saturates the canvas, and then use a spatula to remove the material from the wall. But unlike ordinary paper-based wallpaper, vinyl sheets have the quality of being resistant to water. In this case, it is necessary to use more effective methods struggle.

Water use

In order to quickly tear off the wallpaper from the wall surface, it is necessary to use rolls with spikes. If you don’t have such a device, you can use with a regular knife, but they will have to tread carefully. Due to the multilayer structure, such wallpapers keep the wall intact. With the help of the presented tools, only the first layer of canvases is damaged.

The wallpaper comes off the wall perfectly, sometimes the backing remains

When you have managed to render the first layer of material unusable, you can now take water, add dishwashing liquid to it and apply it to the surface of the wall. Thanks to the added component, the glue will begin to dissolve quickly, and old wallpaper will be easier to remove. To wet the surface, you can use a roller, foam sponge, or spray bottle. In this matter, it is important not to overdo it so that damage does not occur on the floor and wall.

When old wallpaper is saturated with water, you can carry out a procedure to remove it. The process of removing the canvas should occur from the bottom up. All remaining pieces of wallpaper are removed using a spatula. If it is not easy to remove wallpaper from the walls, then you need to apply water to its surface again, and then remove it again. When the vinyl wallpaper adheres very tightly and firmly to the wall, you can not remove it, but carry out further gluing directly on it.

Steam application

Our experts told us interesting way, how to remove vinyl wallpaper using steam, which is used quite rarely, but is very effective.

Using a steam generator to remove wallpaper

You can quickly remove old paintings from walls using steam. To perform this operation, you need to stock up on a steam generator or an iron that has a steaming function. When performing such activities, the steam affects only the first layer of wallpaper, as a result of which they begin to lag behind the wall.

Using steam is not only fast way removing the old coating, but also the cleanest method, because after it no traces of dirt remain. In addition, this option can be used when you need to peel off the interlining.

As an alternative, you can try a wet rag and an iron. The material is laid on the wallpaper, and then run over it with an iron. The resulting effect can be compared to that obtained from using a steam generator.

Related article: Why putty drywall?

Using wallpaper glue

You can remove old paintings from walls using a special composition that dissolves in liquid, as well as a small amount of glue. The resulting product is evenly distributed on the wallpaper, and then allowed to rest for 3 hours. The method used allows you to remove wallpaper not in pieces, but in sheets at once. Everything is simple, because when gluing the canvases, a different wallpaper glue was used.

Simple steps for dismantling wallpaper

You can also remove material using metal brush, sandpaper and sanding machine. But all activities must be carried out carefully and carefully so as not to damage the wall.

Removing wallpaper from drywall

Very often people use it to level walls. plasterboard sheets. They are easy and quick to attach and do not leave behind dirt, as when using plaster. But what if vinyl chips need to be removed from just such a surface? It is important here not to damage the drywall, otherwise you will have to carry out measures to restore it, and this is a waste of time and money.

You should not use water to remove the sheets, because drywall does not tolerate moisture very well. The process of removing material must be carried out very carefully. First, apply a small amount of water, then you need to wait until the top coating of the wallpaper is wet and then take a spatula to carefully remove the old material. In this case, you can add special products to the liquid that are designed to remove vinyl coating specifically.

Plasterboard walls ready for wallpapering

If the gluing process was carried out using special glue for vinyl sheets, the dismantling process will not be difficult. Also, difficulties will not arise provided that putty and primer were applied to the sheets of drywall before applying the wallpaper.

It is very easy to remove non-woven fabrics, because it is possible to delaminate them. To do this, you need to pry off the top layer with a knife after wetting it with water and peel off waste material. If you used PVA compound to glue the wallpaper, then you will not be able to harm the coating. In this case, the integrity of the sheets is necessarily compromised.

Renovating an apartment or house brings with it a huge number of different problems and hassles. No wonder it is believed that repairs are equal to three fires and two floods. Enormous efforts and resources are invested in repairs. To get rid of unnecessary hassle and problems, so that funds are not wasted and efforts are not in vain, preparatory operations should be carried out correctly. No matter what it will be finishing wall covering - wallpaper, painting, decorative plaster, the wall should be as flat as possible. But first you need to clean it. Let's find out how to remove vinyl wallpaper from walls. This is a very popular type of wall decoration. This material has some features that should be taken into account.

Features of vinyl wallpaper

This wallpaper consists of two layers of materials. Often the first is a paper or fabric base. The second layer is a polyvinyl chloride coating. Due to the presence of a paper base, these wallpapers are easy to stick. The polymer finishing layer provides these materials with high resistance to moisture and also makes the coating durable.

The vinyl top can be finished in a variety of ways. There are so-called washable wallpapers, foamed, with silk threads. These surfaces are easy to clean. Some can be washed with water. Others use alcohol and even a solvent. That is why you need to know, quickly and without problems. The fact is that traditional paper wallpaper can be easily removed with ordinary water. But she won't help here.

The method of removing wallpaper also depends on what kind of glue was used during installation. If a professional composition was used, then these are water-soluble mixtures. In this case, the old finish can be easily removed. Also, these wallpapers are glued using water-insoluble adhesives - PVA, bustilate and others. Then you will need to put in more effort. Home craftsmen advise how to remove vinyl wallpaper from walls. There are two ways: in the first case, they act on the glue, and in the second, directly on the wallpaper itself.

Preparatory stage

Before you begin removing vinyl wall coverings, you need to prepare the room. It is best to clear the room of furniture. During the work, it can get dirty and simply get in the way. Interior elements that cannot be removed are covered with film or sheets. It is also better to cover the floors with film. Place sheets of cardboard on top of it or enough thick paper. A damp cloth is laid on the threshold. It will collect dust and debris.

To avoid electrical accidents, experts recommend turning off the power to the wiring. To reduce the risk of moisture getting into sockets, it is recommended to cover them with film.

Materials and tools

Before removing vinyl wallpaper from the walls, you should prepare fixtures, materials and tools. The first step is to prepare a wallpaper tiger - this is a roller with spikes. Then you will need a knife and scrapers. Sponges will come in handy different sizes, as well as foam rollers, rags and rags. Prepare basins and containers for water and solutions, a stepladder, and garbage bags. It is better to carry out work with gloves.

How to remove vinyl wallpaper: methods for removing vinyl wallpaper using water

First of all, the vinyl surface is carefully treated with a spiked roller. This is done so that holes are formed in the moisture-resistant vinyl covering. It's not such a simple process. It will require a lot of effort and time. Wallpaper tiger or roller easily breaks through the layer without damaging the wall.

Then the surface is generously moistened with a warm solution of water, vinegar and fabric softener. It must be remembered that this method is suitable for paper-based coatings. In the area of ​​​​sockets and switches, the solution is applied very carefully. Fast is not always good. Water will enter the holes and cuts, causing the adhesive to swell. Within 15 minutes, the wallpaper can be easily removed from the wall. The thicker the layer of glue, the more intense the moisture should be.

Professionals advise how to remove vinyl wallpaper from walls: it is better to start removing it from the bottom. To do this, the edge is hooked with a spatula and removed. The remaining small fragments can be removed with the same spatula or coarse sandpaper.

Method number 2 for dismantling wallpaper using water

Here, too, the vinyl coating is first treated with a roller or tiger. Then moisturize. The peculiarity is that instead of water, special formulations are used. They are mixed with warm water and applied to the surface. This tool does not act on the paper base, but on the glue. The wallpaper itself will remain intact and undamaged. The composition will dry in 2-3 hours - the manufacturers indicate this in the instructions. Then the canvas can be easily removed almost completely.

If the coating is difficult to remove, in such cases add it to water with a special solution. Cover the wall with this mixture and leave it there for several hours. Then the wallpaper is easily separated from the wall in a single strip without gaps. Some give other recommendations on how to remove old wallpaper. We will talk about them below.

We use a steam generator

Here's another one effective method how to remove old vinyl wallpaper from walls. It is good because it allows you to quickly remove old finishing. Under the influence of hot steam, the glue will swell and dissolve much faster than in the second method. If there is no such generator, then an iron with vertical steam will do.

This method is also good because it eliminates the appearance of dirt.

Mechanical methods

Professionals know that waterproof adhesives can provide better adhesion of vinyl wallpaper to the wall. This is the advantage of this method. But it is very difficult to dismantle wallpaper glued in this way. This is not an easy or quick process. In this case, the wallpaper can only be separated mechanically. So, take a sharp spatula and pry it over the edge of the sheet - at the junction, near the rosettes, at the bottom. Next you just need to peel off the coating. It is useless to wet surfaces. If the bottom layer starts to swell, it's the paper, not the glue.

Removing wallpaper with a spatula is a long process. How to remove vinyl wallpaper? Removing vinyl wallpaper mechanically will be faster if you use a power tool. Can be applied grinding machine, electric drills with special nozzles. But the tools must be used correctly. This removes small pieces and traces of glue, but not the entire fabric.

We work with plasterboard walls

If there are no special problems with a regular wall, then problems may arise with plasterboard ones. This material does not withstand exposure to moisture, especially water. The dismantling method with abundant wetting will not work here. Experts recommend as the most the best option use special compounds that dissolve the glue. If the wallpaper was applied to drywall with PVA-type adhesives, then it will not be possible to remove it. The entire element needs to be replaced.

Recommendations on how to properly peel off vinyl wallpaper on a plasterboard wall

As noted above, vinyl wallpaper can be made on a paper or non-woven basis. How to remove old vinyl wallpaper from walls? The methods are the same as with a regular wall. Wallpaper is sprayed with a special solution, and non-woven wallpaper must first be treated with wallpaper tiger. Only after this is it possible to moisturize them. Only after half an hour can you begin to dismantle vinyl trim walls

Some types of wallpaper will require the use of special tools. But you need to work extremely carefully, as you can easily damage the wall. It is very difficult to remove washable wallpaper. Their coating is made in such a way that they are not afraid of moisture. Here it is best to use irons or steam generators. By removing the coating in small pieces, you can get good result on one's own.

Especially easy to remove paper wallpaper, as well as liquid. The latter do not need to be removed at all - with the help of special paints you can simply change color scheme and change the drawing to suit your taste. However, if the task is to apply a different coating to the wall, then in order to remove liquid-type wallpaper, an aqueous solution or Sander. But there is one drawback - after mechanical removal you will have to sand the wall again. This is an additional waste of time. We'll have to clean the room again from rubbish.

Conclusion

In order for new wallpaper to be pleasing to the eye and last a long time, you need to have a lot of patience. Now you know how to remove vinyl wallpaper from a wall. It won’t be difficult to peel off the old ones using these recommendations. After the wall is cleaned, there is no need to rush. Let it dry. Then you can safely apply the primer.