Devices for picking apples. Making a homemade collection of fruits from trees. Fruit picker with telescopic handle for collecting fruits

How can you still pick an apple if it is on the top branch? If you don’t want to climb on a stepladder, make a fruit picker. At least one like V.S. Krutova from Vyborg. The device is convenient to use, easily separates the fruits from the branch, and does not break the fruits (Fig. 124, A, B).

Rice. 124. Fruit pickers (dimensions in mm): A, B - designs by V.S. Krutova (1 - hole for attaching the bag, 2 - cord, 3 - pole); B - design of I.I. Lyashenko (1 - cutting 3-5 m, 2 - inner stick).

The material is a plate made of of stainless steel thickness 0.2-1 mm. If you don’t have such a plate, a regular tin can will do. But for it to turn into suitable material, required extra work: rivet a spring from an alarm clock to make the glass elastic and rivet a cutting edge machined like the edges of scissors. We will make a bag for collecting fruits from a nylon stocking; it contains 5-6 fruits. You will also need a prefabricated pole (like a fishing rod) and a cord. When removing the fruit, we place the puller under it, turn it around its axis, and if the fruit is not separated, we use a cord, then the apple will be cut like with scissors.

Gardener from Sevastopol I.M. Lyashenko also uses a tin can to make a fruit picker, but in a slightly different way. Three cone-shaped cuts are made in it, 35 mm deep and 25 mm at the top (Fig. 124, B). Any pole 3-4 m long and 35-45 mm thick can be attached to the can. Drill two holes in the jar for 3-4 mm bolts, tighten them with screws of the same thickness. For better fastening, a bar is inserted inside the can. In order not to damage the fruit, glue the yarn from the inside of the device.

The largest and tastiest apples are usually located on the upper branches, and they are very difficult to remove. The fruit pickers sold in the store pick only one fruit at a time. This is very long and inconvenient. You can’t take several pieces at once: the apples break. Gardener from Tula B.F. The storm changed the fruit picker somewhat. I ripped open the textile pocket at the bottom and sewed on an apple duct from 2-3 cotton stockings that had served their time. I cut off their socks, and sewed the stockings themselves to the pocket, one to the other, so that the resulting sleeve did not narrow. In the scheme, each apple, moving apart the walls of the stocking, falls smoothly, without damage. The length of the handle and the number of stockings to be sewn depend on the height of the tree.

N.P. Bezmelnitsyn from Volgograd made a device for removing fruit from a plastic bottle - packaging for detergent(Fig. 125). It will take only 5-10 minutes to cut out the bottom and make a cut in the form of four petals on the cylindrical part near it, place the neck of the bottle on a wooden stick, and attach it to it with a nail. That's all: you have light in hands(weight about 100 g), not damaging the fruit, convenient fruit picker. It is suitable for picking apples and pears; with a diameter of 85 mm, 4 fruits can be placed in it at the same time, with a smaller diameter (76 mm) - 10-15 plums or apricots. The handle can be made removable, and its parts can be connected with an aluminum or duralumin tube.

Rice. 125. Fruit picker design N.P. Bezmelnitsyn (dimensions in mm): 1 - plastic bottle, 2 - wooden detail, 3 - metal part.

A resident of Livny, Oryol region, N. Yasinsky, also got a good fruit picker. The device is easy to use and does not damage the fruit when removing thanks to the soft rubber rollers. A wooden pole made of two halves allows you to remove fruits from a great height. The fruit picker consists, according to the gardener, of a catcher, a pusher and a fabric or mesh bag attached to a pole (Fig. 126). The catcher and pusher are made from one piece of wire rod with a diameter of 3-4 mm, “circles” in the form of a figure eight, bent at an angle of 90°. You can harvest fruits up to 140 mm in diameter.

Rice. 126. Fruit picker designed by N. Yasinsky.

On the fruit picker, which was designed by P.I. Dick from the Stavropol Territory, rims and protrusions for prying fruit are made from a single sheet of durable roofing iron, corrugated along the length of the rim in one line, which gives it additional strength (Fig. 127). After riveting the ends of the rim together, a circle with a diameter of 15 cm is obtained. The 4 cm high protrusions are spaced further apart from each other than on commercially available plastic fruit pickers. A tube made of the same strong iron is riveted obliquely to the rim. A cutting of any length can be inserted into it. Holes are punched at the bottom of the rim, through which a bag is sewn to the rim. When harvesting, it invariably takes a vertical position, so the fruits, and up to one kilogram of them are collected in a bag, do not fall out of it.

Rice. 127. Fruit picker designed by P.I. Dick.

V.D. Saraykin from Donetsk uses a store-bought lopper to remove fruit. Attaches it to the end of a 4-meter wooden pole with a diameter of 40 mm. And just below it attaches a wire ring with a diameter of 400-500 mm with a bag made of rare nylon mesh (Fig. 128). A string of the same length as the pole is tied to the moving end of the lopper.

Rice. 128. Fruit picker design V.D. Saraikin.

Gardener M. Abdusalyamov did not like the purchased fruit picker. I decided to make it to my liking. I took a 6-mm wire and made a ring with a diameter of 15-16 cm from it. I conventionally divided it into four equal parts (Fig. 129). To mark 1 I welded a tube at approximately an angle of 120° to the plane of the ring for the handle, to marks 2 and 4 - teeth at an angle of 60°, to mark 3 - a cutter at the same angle. The teeth, 45 mm high and 10-12 mm wide at the base, are made of bent 5 mm wire, and the cutter is made of a 1.5 mm thick steel plate sharpened from the inside. A 25 cm long bag made of durable fabric is attached to the ring. The cutter helps to pick any fruit from a freely swinging branch without damaging the buds or shaking off the fruits growing nearby. Using his device, the gardener picks up to 15 apples, pears or peaches at a time. During a working day, without any ladder, he collects 300-400 kg of fruit. According to the gardener, the device is also suitable for harvesting grapes.

Rice. 129. Fruit picker designed by M. Abdusalyamov (dimensions in mm):
1, 2, 3, 4 - conditional marks; 5 - ring; 6 - tooth; 7 - cutter; 8 - cloth bag.

His device for picking fruits A.M. Stetsko from the Dnepropetrovsk region makes it using a bench vice or pliers. With the help of these devices, two figures of different shapes are bent from 4-5 mm wire, they are connected at the top and tied together to a pole. A mesh with small cells is attached to the fruit picker (Fig. 130). The stem of an apple or pear is occupied by the corner of the inner figure and is broken off from the stem by turning left and right.

Rice. 130. Fruit picker designed by A.M. Stetsko (dimensions in mm):
1, 2 - parts of the fruit picker, 3 - combined parts, 4 - connection with a pole, 5 - ready-made fruit picker, 6 - fruit clamped in the fruit picker.

The next fruit picker (Fig. 131) was invented by M.I. Shetnev from Brovary. The device also consists of two wire rings (wire cross-section 3-4 mm) with a diameter of 150 mm and two aluminum tubes 300 mm long (from an old clamshell). The ends of the wire wheels are pressed into a tube and riveted. For the bolt that fastens both parts of the fruit picker, holes are made in the tubes 160 mm from the ring. Near it, on a long tube, there is a block for the cord, the end of which is fixed near the second ring. The second tube is connected to the first spring or rubber band to keep both rings at a given distance. A stocking bag is attached to the first ring, and a piece of tarpaulin is sewn to the second ring according to its size. The free end of the first tube is connected to a collapsible pole. When harvesting, the gardener brings the device to the fruit, connects the rings by pulling the cord, the fruit is pressed against the ring and the tarpaulin, the bag opens, and the apple falls into it. If the fruit does not come off immediately, then the fruit picker must be turned in one direction or the other, and the cord should not be released. This can be done when the fruit is already in the bag. It is better to remove 3-5 apples or pears at one time, otherwise the device will be difficult to hold.

Rice. 131. Fruit picker designed by M.I. Shetnev: 1 - ring, 2 - block, 3 - pipe, 4 - bolt, 5 - pole,
6 - stocking, 7 - tarpaulin, 8 - lever, 9 - cord, 10 - spring.

Before covering the rings, the gardener wraps the wire in three layers with insulating tape so as not to damage the fruit. To pick apricots, plums and cherries, he uses a fruit picker of the same design, but with rings of a smaller diameter (25 mm).

And G.I. Tsybulnik from Dnepropetrovsk wanted to help elderly people collect fruits from the ground, especially those that had rolled into the prickly gooseberry bushes. He designed an original collecting device using a thin-walled stainless steel tube with an outer diameter of 12 and a length of 800-850 mm. At one end of the device, the gardener welds a handle made from the same tube, and at the other end he attaches two aluminum tablespoons connected like scissors (Fig. 132). He first bends the same tube, and attaches two aluminum tablespoons to the second one, connected like scissors (Fig. 132). Preliminarily bends the handles of spoons at an angle of 90°, holding them in a vice. Three holes are drilled on the handle of the top spoon, and a weight weighing 40 g is secured at the end of it.

Rice. 132. Fruit picker designed by G.I. Tsybulnik (dimensions in mm):
1 - cork, 2 - plastic ball, 3 - string, 4 - weight.

To the top spoon of EI. Tsybulnik ties a non-stretch cord, the second end of which is tucked into the hole and clamped with a wooden stopper. The cord is secured with a plastic ball with a diameter of 16 mm and a hole of 3.5 mm. The tension of the lace and the distance of the ball from the handle are set at your discretion. With one hand, the burst collector by the handle leads to the fruit lying on the ground, index finger presses on the ball - the spoons clamp the fruit, and when he brings it to a bucket or basket, releases the ball, the spoons release the fruit under the action of the load.

That's all about apple trees. However, not only they grow in the garden, but also other species. fruit trees. About them specific features and the ability of gardeners to "please" their pets will also be described in the book.

When the time comes to pick fruits from tall trees, the most beautiful and ripe ones are so high that even with the help of a stepladder it is impossible to reach them. Of course, you can use a long stick to knock down the fruits. Some summer residents shake the trees, but the apples are damaged and lose their attractiveness. appearance. An alternative solution is to use an apple picker. If you don’t have it at hand, and you don’t want to spend money on purchasing it, then you can make such a tool yourself in a short time. As a result, it will be possible to obtain a fruit picker that will not differ in efficiency of use from that produced in a factory.

Selection of design features before production begins

If we consider fruit pickers, they can be divided into several groups. The first of them are tools that are equipped with cutters at the end of the rod. With this add-on, it is possible to cut off the stem and the apple will fall into a container located in close proximity to the cutter. This apple picking device has a movable knife, which is driven by a special rod. To Work with similar device quite tedious, since the cutter is located on the rod, or rather, on its long arm. This creates extra weight, which is quite respectable. A device for picking apples may also belong to the second group, the tools of which resemble mechanical arm equipped with fingers. The latter are made of wire. After the apple or pear is grabbed with the help of special fingers, the latter are clamped by means of traction, and the fruit ends up in the container. This action made with traditional twine. This is what allows you to tear off the fetus. The disadvantage of this tool is that the branch itself may break off along with the pear or apple.

The third group of fruit pickers

If you are making a device for picking apples, then you can take as a basis the third group, which is the most common in terms of design features. Such structures are made of elastic lightweight plastic or fabric. And the shape of the product is a bowl equipped with petals. A special container must be attached to a wooden pole. The apples are removed by simply turning the pole around an axis that is oriented lengthwise. In this case, the leg is trimmed using the petals of the tool.

Preparing to make a fruit picker

A device for picking apples from a tree should be made only after you have chosen one of the proposed ideas. The third variety will form the basis for a simplified design of a tool for picking fruits. First you need to prepare a plastic bottle. If you have to collect fruits that are quite impressive in size, then a container volume of up to 2 liters is suitable, while for medium-sized apples or pears a bottle with a volume limited to 1.5 liters is suitable. Every summer resident probably has such bottles in stock.

Process technology

If you are making a device for picking apples with your own hands, then you need to cut off the bottom of the bottle, and then make a corner cutout. It will be convenient to use both a knife and scissors. The above cut along the bottle can also be made on the opposite side.

After the bowl has been prepared, it needs to be attached to a pole, the last of which can be a long, light strip. Fixation can be done using wire or self-adhesive adhesive tape. After this, we can assume that the fruit picker is ready for use. To use it, the tool must be brought from below the pear or apple, and then rotated around its axis. This will allow you to cut off the fetal leg using the cutout located on the tool. The apple will end up in a bottle that can simultaneously serve as a collection container and a cutter. A similar device for picking apples from a plastic bottle can be used without lowering the container for some time. Several fruits can fit in one bottle.

Making a fruit picker from a bottle and fishing line

Before you make a device for picking apples, you need to decide design features future instrument. The basis can be the same plastic bottle, a mop handle, which is sometimes replaced with a PVC pipe or fishing line. The length of the latter can vary from 2.5 to 3 meters. You will need scissors and an awl.

Manufacturing process

First you will need to make the so-called enough, which is made from a plastic bottle. The bottom of the container must be cut in such a way that it looks like a crown. Two holes are made in each petal; for this you can use an awl or a hole punch. At the next stage, the product should be given tenacity. For this, a fishing line is used, which is pulled through the neck into the container so that its upper end is threaded into each hole in a circle. You need to bring the fishing line back through the neck. This will allow you to get a bottle that is devoid of a bottom. Two long ends will come out through the neck.

The next step is to fix the holder, which should be a full PVC pipe. The double fishing line from the bottle needs to be threaded through the hole in the holder, leading out reverse side. If the mop handle has a removable handle, then this is a good decision. The ends of the fishing line must be secured to this part of the holder. Two holes are made in the handle into which the fishing line is threaded, the ends are fixed on the other side by stretching. The handle is then put back on the handle. If you are making devices for picking pears and apples, then it is important to assemble the entire structure in such a way that the plastic bottle is tightly attached to the holder. The cut edges of the bottle are bent. In this case, you need to make grasping movements. This is the principle of collecting fruits using this tool. If the mop does not have a removable part, then you need to remove its end, and you should retreat 10 cm. You need to make two holes on the sides where the ends of the fishing line are threaded. Afterwards they need to be fixed together and then tied.

For a PVC pipe, you can use several bottle caps as a handle. If you use ten caps, making a hole in the central part of each with an awl, then the free ends of the fishing line can be threaded through the caps, securing them to the last one. For the stability of the covers, you need to glue them together or make a knot, placing it with inside first cover. This will allow you to get a fairly comfortable removable handle made of caps. In this case, it is necessary to use the same technology as in the case of a mop handle.

Conclusion

If you decide to make a device for picking apples from the ground, then you can use one of the technologies described above. However, the bottle may have to be placed not along the holder stick, but at some angle. This will allow you to collect up to four apples in one container, depending on the size, and then pour them into a bucket. One of the listed devices is quite easy to make yourself. To do this, you don’t even have to visit the store to purchase materials.

If the harvest of your apples is “on top” in every sense, this cannot but rejoice! But getting ripe, juicy fruits from this height is not an easy task. An ordinary garden ladder can also help in this matter, but modern gardeners are used to saving time and effort. Therefore, today we will learn together how to make a device for removing apples from a tree, which will help you quickly and without loss to harvest the entire crop from any apple tree.

If you have only one or two trees with apples on your plot, then there is no point in making a “major” fruit picker; it is enough to make a simple device from a plastic bottle. Well, if you have a whole apple plantation at your dacha, then it’s best for you to buy a ready-made fruit picker

In the markets gardening tools we have seen more than once ready-made devices for collecting fruits. Based on their principle, we will create a fruit picker with our own hands. Our future fruit collector must meet the following requirements: reach high and hold the fruit firmly, and be convenient to use. Let's look at the options that experienced and resourceful gardeners offer us.

As a rule, fruit pickers are made of plastic, but there are metal options. For example, the fruit picker, which is shown in the photo, costs around 700 rubles in stores, it is quite expensive, but the purchase will justify itself and will serve you for many years

But such a device for removing apples from a tree will cost, on average, 1,200 rubles. Its advantage is that it is made of plastic and does not require special care, just store it in some shed and it will serve you for decades

Option number 1: the tenacious hand of the farmer

The device will consist of a grip and a holder. You will need:

old plastic bottle;
long fishing line (2.5-3 meters), awl, scissors;
handle from an old plastic mop (can be replaced with a PVC pipe).

The manufacturing process of this fruit collector in the program “Crazy Hands”:

So let's begin our easy work.

Step 1. We made enough (a two-liter plastic bottle). We cut the bottom of the bottle crown-shaped to form “petals.” We make 2 holes in each of the petals. To do this, you can use a small hole punch or a regular awl.

Now let's give the bowl some grip. Take the fishing line and pull it through the neck into the bottle so that the latter is just below the middle of the fishing line. We pass the upper end of the fishing line one by one into each hole in a circle and bring it back through the neck of the bottle. Thus, we got a plastic bottle without a bottom with two long ends of fishing line coming out through the neck.

Step 2. Attach the holder. We use a hollow PVC pipe or a handle from an old plastic mop as a holder. A double line made from a plastic bottle is threaded through the hole in the holder and comes out the other side. If your mop handle has a removable handle, you're in luck! The ends of the fishing line should be secured to this part of the holder. Make 2 holes in the handle and thread the fishing line through, securing the ends tightly together. Place the handle back onto the mop handle.

We have a plastic bottle fastened with a fishing line with a holder with a removable handle. Now try to remove the cap again, pulling the line slightly towards you. The cut edges of the bottle are compressed, while making grasping movements. Now not a single apple will leave you!

A diagram of another device for collecting fruits from trees: it will take a lot of time to create, so we do not recommend that you undertake its creation. They just showed what else homemade devices can be made

If the mop does not have a removable part, you can simply cut off its end by 15-10 cm. Make 2 holes on its sides, where the ends of the fishing line will be drawn. Then fasten them by tying them together.

Again, if you have a lot fruit trees, then it’s better to spend some money and buy a ready-made fruit picker that will serve you for more than one season

For PVC pipes You can use several caps from plastic bottles as a handle. For example, take 10 covers and make a hole in the center of each with an awl. Thread the free ends of the fishing line into the caps one by one and secure them to the last one. For stability, glue the caps together or make a knot from fishing line on the inside of the first cap. It turns out comfortable removable handle from caps. Use it the same way you use a mop handle.

Video option for making a fruit picker with your own hands

And another option for creating a capital fruit picker

Option number 2: the simplest apple picker

1. Fruit collector with bowl

Step 1. And again we cannot do without such a necessary household item as a plastic bottle. Cut it in half, separating the bottom part from the neck. We don't need the bottom anymore. We cut out deep teeth on the cut edge, and drill 2 opposite holes in the neck.

Step 2. Prepare a wooden pole, one end of which is adapted to fit the hole of the bottle. A handle from an old garden tool will do. Now we put the bottle neck on the pole and secure it with two self-tapping screws.

Use this device to collect apples like this: bring the device to the branch with the apple; Place the apple inside the bottle and rotate the device for removing apples from the tree clockwise. The teeth cut off the fruit and it ends up inside the bottle. You can pick 2-3 apples at a time.

2. Closed fruit collector

You don’t have to cut off the bottom of the bottle, just cut it out round hole on the side. From the bottom side of the hole, make several cloves. Then put the bottle on the pole in the already known way and start collecting apples. The fruits are placed inside the bottle and picked in one motion. A closed fruit picker picks apples more easily, but can pick no more than two fruits at a time.

Using such a device you won’t be able to collect many apples at one time, but the advantage of this device is the speed of its production: if you have all the materials at hand, you will need a maximum of five minutes, or even less

The design of the device is simple: we cut a heart-shaped hole on the side of a plastic bottle, use a screw or electrical tape to attach the bottle to the holder and we can start picking apples or other fruits

Now you don’t need to master the science of climbing trees and endless maneuvers with garden stepladders, and you no longer have to wonder how to remove apples from a tall tree. The juiciest apples will be picked without difficulty thanks to your skillful hands and desire. A bowl of such homemade fruit pickers will last you a couple of years. Once worn out, it can be easily replaced using a new plastic bottle. Well, all you can do is wish that the fruits of your skill will definitely help you get all the fruits from your apple trees!

With the onset of autumn, amateur gardeners are increasingly ordering a garden fruit collector.

Without which it is simply impossible to harvest the crop without damaging it. When the garden is still young, an apple picker with a telescopic handle seems to be of no use. After all, it is possible to harvest crops from not tall young trees without any equipment. The older the garden becomes and the taller the trees, the more difficult the cleaning process becomes every year. Ladders and climbing trees with a bucket in our modern times no longer suits everyone. Especially if the gardener is of retirement age. These devices were developed to help them. To many experienced gardeners fruit pickers are not new. But beginners need to know.

What is a fruit picker or fruit collector for fruits?

Those who are used to it call this device that way. Each summer resident calls it differently, some are fruit collectors, some are fruit pickers. These are synonyms that have the same goal and task. There is also a telescopic fruit collector for cherries. We’ll also figure out what telescopic means.

The fruit collector or fruit picker is:

a device used for harvesting crops in the garden. When the trees are tall enough and there is a lot of fruit, the harvest must be harvested as soon as possible. So that they do not get caught and damaged. After all, in this form they will quickly deteriorate;
The fruit collector will help you collect them without damage and quickly enough. It all depends on the volume of the harvest. We didn’t have time to collect it in time, the birds were already right there. They pecked everything, and not only did they eat it, but they spoiled it;
if there is a need to protect fruits from birds, then you can use an inexpensive, but effective method. Garden protection nets are not an expensive and not difficult to use means of protection.

If a fruit collector for harvesting in an orchard is said to be telescopic, this means that it has a rod. Which is one with him. Such a rod can change its length.

A fruit picker with a telescopic handle is always necessary

If we are talking about harvesting trees, and they can be more than one meter high, then it is clear that the length of the fruit picker is not enough to reach the fruit. Therefore, a rod must be attached to it. Which can be sold separately or included in the kit. The rods are:

wooden,
plastic,
telescopic.

Wooden and plastic ones have a fixed length, while telescopic ones come in different lengths. The fruit picker for apricots with a telescopic rod is very convenient, and harvesting with its help will not be difficult. Such a fruit picker with a telescopic handle is sure to come in handy for cherries that grow very high. When the standard length of a wooden rod is not enough, then you need a rod whose length can be adjusted.

Which trees can be harvested with a fruit picker?

With its help, you can remove small fruits, such as cherries, without damage. And big ones, like apples.

The device allows you to harvest from almost all types of trees:

pears,
cherries
mandarin,
quinces,
persimmons,
drain,
cherry plums,
peaches,
apricot,

nuts,
chestnut,
apple trees,
cherries,
grapes,
other.

Peach, like plum, is very delicate and will definitely break if dropped. Therefore, it must be removed from the tree with extreme caution. Although the fruits of apple trees are harder, at the slightest impact on the ground, a dent and crack will form on them. In which microbes will definitely get in. And the life of such a fruit is doomed to rot, even if it belongs to winter variety With long term storage So that apples from your personal orchard can be tasted during the New Year holidays, you need a telescopic apple picker. And then some fruits will be able to last until spring.

What is a fruit picker for apples and its principle of operation?

Device for harvesting orchard designed in such a way that the fruit, after being torn from the branch, falls into a special container. And he stayed there until he was put in a box or basket. Thus, a device for harvesting crops in the garden can be of several types.

1. Collet:

wire,
with a bag,
with grip.

2. Plastic, in the form of a glass:

the walls of which are cut into strips with edges rounded at the top. Such fruit harvesting devices are also called Tulip Fruit Pickers. Since its appearance resembles this flower;
we pry the apple so that its stem falls between the petals. Next, rotate the tulip in any convenient direction;

the stalk is torn off the branch, the apple remains in the tulip. And then it goes to the trash can.

collet wire

Wire ones are:

a device resembling an unopened flower. At the ends of the petals of such a flower there are curved edges of the wire;
in order to stretch a strong thread into these holes. It is needed to hold the fruit when the stalk is torn from the branch;
When the pear falls into such a socket, you need to pull the thread. The socket will close and the fruit will fall safely into the basket.

Collet with bag

Collet devices with a bag are:

a ring to which a small pouch is attached. At the other end of the ring are the same petal blades. Which serve as a kind of grip or a kind of knife. They also say fruit basket;

The bag is designed for simultaneous removal of several fruits. If a gardener is physically able to hold not one pear, but five or more, then why not. Such fruit collectors greatly speed up the harvesting process;
Some designs of this type feature a sharp metal blade attached to the ring. The mounting location is chosen in such a way that its sharp side is the second part of the blade;
getting into a hole with a knife sharp on one side will cut the stalk faster. For grapes whose clusters are very firmly attached to the vine, this is a good suggestion.

Collet with gripper

Each telescopic fruit picker with a grip works on the principle of preventing the fruit from falling when it is torn from the tree branch. Its task is also to:

the pear, plum or cherries did not fall out of the device on the way to the box. The biggest and delicious fruits ripen on the tops of trees, closer to the sun. And a grip is required to remove them. A fruit picker with a gripper is a fruit picker design that in some cases simply cannot be done without;
modern design Some devices allow you to release the grip with one light press. They are light in weight and can be handled with just one hand. Even a schoolchild will be very happy to work in the garden with such a modern assistant. Bright and modern design which will please any summer resident.

You can buy an apple picker with a telescopic handle in our online store at any time. Check out the assortment of this product category and place an order.

Every year we struggle with picking apples. The trees have grown tall, and the usual puller - a “glass” with slots - is inconvenient to use: it is difficult to “drive” the stalk into the crack. Maybe there are some homemade designs that will help solve this problem. Otherwise, the harvest season will soon come, and I wouldn’t want to “poke” the fruits again with a clumsy puller.
Anastasia Valentinovna PETRAKOVSKAYA, Vitebsk region, Novopolotsk

I suggest homemade design, which will help you easily remove fruits from the greatest height.

Fruit picker design features

The main parts of the puller are two plastic bottles and an aluminum ski pole. The design of the puller is shown in Fig. 1.

Bottle 1 is selected depending on the size of the fruit, for example, 1.5 or 2 liters. This bottle has half of the bottom and part of the side wall cut out to allow fruit to pass through. In the remaining part of the bottom there are 2-3 narrow slits for capturing and breaking off the stalk. The cork is firmly fixed (glued) to the neck and a round hole is cut in it the diameter of the stick.

Bottle 2 is chosen to be smaller in volume and its bottom is completely cut off. It has a removable plug with a hole for passing a stick. Both bottles are sewn together with fishing line approximately 0.2 mm in diameter and secured into a single rigid block. The bottle caps have holes the diameter of a ski pole.

Method of sewing bottles for fruit picker

To sew bottles together, use a hot awl to punch paired holes on both sides of the seam line. We bend a thin copper wire in half, twist the ends and make a “needle” in the shape of a fishhook (Fig. 2).

Using this flexible “needle,” we insert the fishing line through adjacent pairs of holes and connect the bottles into a single block. With this method of stitching, your hands will always be outside the bottles.

A block of two bottles is put on a ski pole, in which (after fitting) a hole is drilled and a pin is rigidly fixed (Fig. 3). The length of the pin should correspond to the diameter of the bottle neck and the internal diameter of the stopper. On the neck of the bottle, you need to make 2 small diametrical cuts to fix the block of bottles on the pin.

The figure shows the cork removed from bottle 2. In this case, the bottle block can be freely removed from the ski pole. When screwing the cork onto the neck of the bottle 2, the pin firmly fixes the block of bottles on the stick.

The picture also shows a ring that prevents the plug from sliding down the stick and losing the plug. The ring is made of adhesive tape or electrical tape.

The entire design of the puller is extremely lightweight and easy to use.

Operating principle of the apple picker

We introduce the fruit through the cutout into bottle 1 and pick it off with the side wall or bottom. 3-4 apples (pears) or 15-20 plums are placed in the puller.

We lower the entire puller to a horizontal position. In this case, the remaining part of the bottom of the bottle 1 keeps the fruit from spilling out. Having unscrewed the cap 2, remove the bottle block from the stick, and pour the fruit through the cutout into a bucket or basket.

When collecting fruits from the lower branches of a tree, the harvester walks freely on the ground, and when collecting from the upper branches of a tree, he climbs onto a stepladder.