Hammock - manufacturing at home: options, drawings, weaving. Weaving a hammock with your own hands: a diagram of the product, how to use it, the history of the origin of this item and instructions for its implementation using the macrame technique How to make a hammock from

Any person who has own house or country cottage area, dreams of at least occasionally lying in a hammock, hiding from the hot rays of the sun. However, many people tend to think that it is almost impossible or very difficult to weave a hammock with your own hands. But this is absolutely not true. under the power of everyone. It just takes a little patience.

Therefore, consider different ways how to weave a hammock.

Today, there are many types of different hammocks. Accordingly, the materials used for them are also different. The most popular is Brazilian. It is distinguished by the relative simplicity of weaving and high strength and durability.

Brazilian hammock weaving

Before you start weaving a hammock with your own hands, get necessary materials. There are only two of them: this is a very thick cord that can withstand up to 200 kg (it will take about 25 meters), and a large canvas of strong fabric, the average size of which is about 230 × 120 cm. Nothing else is needed to weave this type of hammock, except for your skillful hands.

So, we start by taking a piece of fabric and carefully sewing it on all four sides. This is necessary so that the edges do not fray. Next, we make blanks from the ropes. To do this, cut off about 12 pieces from the rope. At the same time, the length of each is 15 cm. This will be a kind of basis for the initial loops.

On each side of the hammock, you need to put 6 such ropes, after folding each one in half, with a grip of 2-2.5 cm, and sew. You will get something similar to a fringe about 3 cm long. Remember to keep a distance of 10 cm between the ropes when applying and stitching.

And in order to have more confidence in the reliability of the hammock, it is also advisable to additionally stitch the edge of the fabric with loops with a thick ribbon. Now, through the resulting loops, we pass a cord 75 cm long, the ends of which are then tied. It turns out that all the loops are connected with a cord at the edge into one.

You also need to do on the second side of the hammock. After that, we take the rest of the cord, make a couple more knots and twist the two tails into one according to the pigtail principle. At the end, we tie all this several more times, leaving about 25 cm free. With these ends we tie the rope to a thick tree branch. We do the same on the other side and also tie the other end of the canvas to the tree. So you get a hammock in which you can lie, swing and enjoy the fresh air.

Back to index

Hammock with full wicker base

The next type of hammock is more complex, since its entire base is completely woven from the cord. To work, you will need as many meters as possible (minimum 150) of a very strong cord, scissors and two wooden planks 80 cm long each.

Let's start with planks. In each piece of wood, it is necessary to make 6 holes at a distance of about 5.5-6 cm from each other. The thickness of the holes must be such that the double cord can pass through them normally. After that, cut the cord into 12 equal segments. The length of each such segment is at least 3 times the estimated length of your future hammock.

Now we take two segments and push them into the hole on wooden block. We do this with all cords. Now we take the outer tips, the length of which should be at least 1.5 meters, tie them all together, twist and make a loop, for which the hammock will then be attached on one side.

All other ends of the cord, which are located in the inner part, must be tied two by two to each other in the form of knots, as shown in the diagram. At the same time, it is important that in the finished knot one lace is from one hole, and the second is from the next nearby one.

Stages of making a hammock: 1 - Assembling a hammock, 2 - Tying the cords, 3 - Fastening the rope.

So we get the first finished row of a hammock. All subsequent rows are made according to the same principle. It is very important not to forget to tie only those ends of the ropes that come out of adjacent holes, and not from one. Also try to get the resulting cells were the same and not too large. After all, a hammock with smaller mesh cells will withstand significantly greater loads.

After you weave the length of the hammock you need, you need to push the two ends of the remaining ropes from different holes into one on the second prepared wooden plank. After that, the ends must be tied, and the outer tips should be connected together and also tied into several knots. After that, twist them and make a loop for which the hammock will be hung from the other side. Now you can safely use such a hammock for relaxation.

Looking for tips on how to make a DIY hammock led you to the right place. Here they will tell you how to make a hanging bed for rest and sleep, as well as provide drawings and recommendations. The fact is that hammocks can be very simple, the manufacture of which does not require large expenditures. manual labor. The main thing is to carefully select the materials and carefully follow the instructions. For those who want to get something special at home or in the country, a master class of more complex products is offered.

Hammock in the style of "sling"

Mexican hanging stock is easy to make at home. It will only be necessary to pick up two dense pieces of fabric from improvised materials (the width of each segment is 1.5 m, the length is 3.2 m), which should be tucked up and stitched along the edges.

Note! To get out of the Mexican hammock, you need to go through a separate master class (just kidding!). However, it is really impossible to fall out of it, and in order to climb, you will need to make an effort. Therefore, it is inconvenient for the elderly. But the lightness and compactness make this model indispensable in the campaign.

The proposed hammock has design feature, thanks to which it can be used in 2 versions: enveloping (original) and spacious. Modification is achieved by inserting a dense fabric (mat) inside the bed through the holes marked in yellow in the figure. Study the drawing and get down to business:

1. 2 meters of fabric on both sides, marked in green, should be sewn.
2. 1.5 meters each, marked in red, must be stitched, tucked 2-3 cm.
3. Pull the cord through the holes made at the edges.
4. Cross the cord and tighten the ends, gathering the fabric into a knot.
5. Wrap the ends of the cord 2 times around the place of contraction and tie them with a noose knot.
6. With ropes intended for hanging, wrap around the tree.
7. Then attach the ropes to the knots that fix the edges of the hammock.

The structure will hold more firmly, and the tree will not be damaged if fabric is first placed under the ropes. Alternatively, hanging ropes can be threaded into the tubes. Check the strength, adjust the tension and enjoy the rest, the master class on making the simplest hammock is over!

wicker hammock

A hanging bed made of a whole canvas, of course, is easier to make. However, a hammock mounted on transverse sticks is more spacious and comfortable. And despite the complexity of the process, many people like just such a design. There are several options for knots for a hammock, each of them has its own advantages and disadvantages. Before you make a hammock with your own hands, you will have to master the skills of weaving macrame.

• Throwed threads (without knots, the threads are simply thrown over, as in factory hammocks). Advantages: the net is woven very quickly, this method of weaving is the least material-intensive, the resulting fabric is quite flat (the knots are not pressed into the body when lying down, even without lining the fabric). Disadvantages: the cells are unstable, easily changing size. Over time, holes will appear in the hammock, which will not add comfort.

• Square knots (double flat knot). Advantages: very dense plexus, the cells are clearly fixed, the knots are flat, the cell size is easy to correct. Disadvantages: the most material-intensive method and, therefore, the resulting hammock will be the heaviest. Taking such a hammock with you on the road is expensive.

• Flat knots (degenerate square knot, without two threads inside the knot). Advantages: the net weaves quickly, it is easy to adjust the size of the cells, the rope consumption is low. Disadvantage: there is a possibility of eversion of the knot with excessive load on the thread.

Flat knot weaving pattern

• Triangular knots (bowline), from such knots knit networks for the most different needs. Advantage: the cells are fixed rigidly. As a positive point, one can also note the average consumption of the rope and, therefore, average weight. Disadvantages: the work of weaving such a network is the most time-consuming, the knots on one side are sharp, the size of the cells is difficult to edit.

Triangular Knot: One Side View

Triangular knot: view from the opposite side

One of the possible patterns for weaving a triangular knot

Dilemma: with or without a corner?

Before you make a hammock with your own hands, you need to decide whether to bring all the threads into a ring, as in factory products, or not. The corner (this is the name of such a constructive solution) looks quite attractive, but it is not so easy to tie it at home.

To just as effectively bring all the threads into a ring, you have to try. In addition, it should be noted that the resulting angle will be very dense, almost not subject to deformation. As a result, the compactness of this hammock model will decrease, and it will not be so convenient to take it on a hike.

Weaving a hammock at home, and even for the first time when any action is an experiment, leaves its own individual imprint on the accuracy of measurements. Therefore, we can recommend taking materials with some margin, because it is easier to cut than to finish. In order to build a corner, you will need 20 free ends (10 threads, 10 passes), which will be attached to the net as a result. All threads are of the same length, after pulling them out of the corner you will get a straight line consisting of free ends. These ends are then passed through the crossbar and attached to the net. You can take 10 threads of 300 cm each, folded in half they will look like 20 threads of 150 cm each. The result will be about 40 cm from the top of the triangle to the crossbar.

The subtleties of weaving

Most often, a hammock designed for giving and country house, woven in a bowline knot. The reason lies in the rigid fixation, which is in demand not only in hanging places for recreation, but also in a wide variety of things: sports nets, bags and pouches, fishing nets, firmware and lace. The thickness of the nylon rope must be at least 6 mm. You should choose a dense winding with nylon filling.

Sometimes in discussions you can hear that this or that master used a thread with a thickness of about 4 mm. If you are sure that you will not allow children to test it for a hammock, you can try it. Otherwise, the hanging bed, on which a large man is able to sleep calmly, may not withstand one or two pranksters. You should not get carried away with excessive strength either: a hammock, for the manufacture of which a rope 10 cm thick went, will resemble a volleyball net. This, of course, will add reliability, but such a “bed” will look terrible.

The consumption of the rope depends on the method by which knitting is performed, the desired dimensions of the bed and the size of the cells. The larger they are, the less material will be needed, however, keep in mind the fact that any mesh will slightly deform over time. When weaving a triangular knot of cells with a diameter of 65 mm, 40 5-meter threads will be required, the total material consumption is 200 m. With such calculations, the planned canvas should turn out to be 180x70 cm in size from diamond-shaped cells 40x80 mm.

A master class covering the knitting of a hammock will be incomplete if you do not mention the need to strengthen the longitudinal edges of the fabric. They should be reinforced with strapping capable of withstanding the maximum load generated during lifting or laying down. You will need to make a very tight knit from the same material that went to the main bed, or you should look for a thicker rope for a similar purpose. Approximately for weaving 1 m of rope, 5.55 m of thread will be needed.

If the hammock will be used mainly stationary, in the country or at home, a model with an angle will look preferable. The reason for this choice has already been discussed above. The number of ropes in the net should be selected as a multiple of 4 - the reason is that 2 threads on the edge of the net will be fixed for 1 corner thread. That, in turn, is formed from an even number of ropes. In addition, it must be remembered that the longitudinal ropes also require fastening. There are 2 possible solutions to this issue, with which a schematic drawing will acquaint you.

In the picture on the left, the side ropes are fixed separately on the crossbar, the entire network is woven from a number of threads that is a multiple of 4 (for example, from 40). The schematic drawing on the right suggests making a mesh of 38 threads, and align the side ropes when tying with an angle with the outermost threads.

Hurry without haste

Whoever hurries will make the neighbors laugh (or at least the neighbor's children)! No matter how good the master class is, no matter how skillful hands you didn’t have it, it’s still not worth starting sewing a hammock on the go. Be sure to make test weaving, at least from 8 threads. It will help to reveal the shortcomings of this or that method and will reveal a few previously unaccounted for trifles.

Look for a simple rope in the country or at home, 8 pieces of 2 meters will be enough, something made of wood (for the cross) and try different variants nodes and cell sizes. When you decide what you want to sew, what drawing you take as a basis, weave the mesh along the entire length of the threads. Measure the dimensions of the resulting model and estimate how many materials will be needed for the entire structure.

Once you have the required rope, do the second test set. Take 2 pieces of 10 meters, tie them around a round block of wood (get 4 ends of 5 meters). Weave the mesh, measure the remnants of the threads (do not forget to leave 25 cm at the ends to secure the fabric), make adjustments to your calculations, because this is inevitable, at home, accuracy is achieved only by experience.

The choice of fabric or the decision to make a children's hammock for your child make their own adjustments to the calculations. However, now, after several approaches, you know exactly how to weave a hammock. And after making your first model, you will be ready to conduct a master class!

This article - detailed story about how to do wicker hammock with your own hands. What to look for, what are the options for knots and weaving. How to determine the size, where the rake lies and how not to step on them. Is it even worth taking on this job? This is a story about gaining personal experience.

Preamble

Surely everyone knows from childhood what a hammock is. Perhaps someone even lucky to lie down in it. If you don’t know what we are talking about, go to Wikipedia.

There is a wonderful company, "Expedition", which produces all sorts of tourist swag and jokes on the subject. So I came across their "jokes" in the store, among other things I saw a fully functioning hammock. Only not wicker, but from a whole canvas. It cost about 800r. All this is cool, of course, but there are no transverse sticks in it, which means you have to lie like in a bag - not a fountain. So you have to do it yourself. I was going to take it on weekend hikes. The fuse was received, rushed ..

Search

I googled on the topic, I found a lot, but it's not that. I found a couple of sources copied from the same article from the magazine "Young Technician" No. 6, 1983! Yes, glorious 83rd, "wonderful time of childhood, wooden Toys, nailed to the floor .." An attack of nostalgia was replaced by disappointment: pictures of poor quality, the names of the knots are the same as in Chinese. By the way, an article roams in Runet on how to make a rag hammock. Pattern, explanations, everything is painted to the smallest detail. But to the topic this story does not apply.

Switched to English search. As a result, dozens of American sites offer to buy (!) the same models of hammocks. A large selection of prices, colors, materials and all that .. but not our choice :) And not a single decent site with a story like "hand made". Here it is - capitalism face :) - any whim for your money.

In general, I collect from the world one by one. Found a site dedicated to macrame. Not even a website, but rather a home page. Nevertheless, the truth was revealed there! Schemes of almost all the necessary nodes, the definition of concepts. Thanks to the author, "respect and respect"! :)

Choice of method

With the terms defined, experiments began. I found four ways to weave the main fabric (mesh):

Another interesting point. On factory hammocks, all the threads are brought together into a ring, and this information looks very nice. It's called the corner.

How I steamed to get the same angle! So many approaches and searches .. I almost abandoned this idea, but still I was able to weave the desired pattern. Peeped in the series "How it's done." Attention: this angle is very dense, practically does not deform. That. in a twisted hammock, it will stand out strongly, that is, stick around :) (this is again for using a hammock in field conditions).

Schemes of weaving "square knot", "bowline" and "corner" in this archive.

I did not weave a whole canvas in all ways, because. time and money costly. I tried to weave on eight test threads, two meters each, well, I figured out how it would most likely look.

Eventually "behind" And "against":

1. 
   + weaves very quickly, you need a minimum of ropes, the canvas is almost flat.
   - the cells will be floating, i.e. will easily change size, which means you get "holes" in the box. There will likely be discomfort.
2. square knots
   + the most dense plexus, relatively fixed cells, flat knots, the size of the cell is easily corrected. Theoretically, there should be no discomfort at all.
   - ropes need two times more than in other ways, the weight will also turn out two times more. But weight is already a critical factor if you take a hammock with you, for example, in a PVD.
3. flat knots
   + weaves quickly, the size of the cells is easily corrected, minimum flow ropes.
   - we load one thread - the knot turns out (see on photos bottom left). Perhaps nothing will happen in the composition of the canvas, but I did not like this behavior.
4. triangular knots
   + rigidly fixed cells, average rope consumption, hence average weight.
   - it is weaved for a very long time, on the one hand the knots are sharp. Each cell has to be measured, it is difficult to correct the size. After four hours of work, my fingers hurt. Have to throw.

Well, here we go.. :)

Before going any further, I need to clarify the following: all the figures given are my measurements, yours may be different. My work plan and calculations changed several times. Instead of 38 threads, in the end, I weaved a net of 40. At first, there was a lot of rope I bought - when I only made the canvas, then it was barely enough - when I made the corners and side ropes. Therefore, approach the matter creatively, it is unlikely that everything will be calculated exactly.

After all the tests and measurements, I still decided to weave the main fabric on triangular knots. In a tourist shop I found a nylon rope with a diameter of 6 mm. Not some dubious Chinese town, but a wayward line "Needle line": dense winding, nylon filling, 5 rubles / m. Stretching per meter of rope: I was able to stretch it by 5 cm, let it go - the rope returned by 2 cm. It seemed to be quite strong. In the same store I saw a finished hammock of Chinese scammers, woven in the first way from an ordinary rope ~ 10 mm thick. With his appearance, he resembled a school volleyball net - a terrible view, although reliable.

Note: I read somewhere on the forum that the thickness of the rope should be at least 4 mm. I think it's very subtle.

We decided on the thickness, but how much to take? During the test weaving, I came to the following (only for weaving with triangular knots): I make cells of 65 mm, from 40 threads of 5 meters each, the consumption is 200 m of rope. I assume that the canvas will stretch and the cells will be diamond-shaped. I plan to get a canvas 180x70cm from rhomboid cells, the diagonal of the rhombus is 40 and 80 mm. If the cells are made larger, the rope will need to be less, but I cannot say what the ratio of the cell to the length of the thread will be.

Side ropes. The edges of the hammock need to be tied, and this harness will receive the maximum load - body weight, when the user gets up / lies down in the hammock. Therefore, either a very tight knit or a thick rope is needed. Again found the answer - "How it's done." Calculation: 5.55 m of rope - 1 m of rope.

If you plan to make a hammock with corners, then the number of mesh threads should be a multiple of 4. Why? Every two threads at the ends of the mesh will be connected to one corner thread. The corner, in turn, is also assembled from an even number of threads. Hence the divider 4. On the other hand, you need to take into account the presence of side ropes (they also need to be fixed). Options: you can weave a net of multiples of four threads (for example 40), tie them with an angle, and fasten the side ropes separately to the crossbars. Or: a net of 38 threads together with two side ropes will be tied with an angle.

I can’t explain this idea with photographs, because on my hammock I spun such that I would have to shoot a 3D video :-/ I can only give a schematic drawing:

Rake

Problem number 1. When I took measurements on the test weave, I used 8 strands. So I did not take into account that woven 36-40 threads will give a completely different width than calculated (measurement errors). In general, my width turned out to be 85 cm instead of the calculated 70 cm (!).

What needed to be done? weave one row of all threads and measure. I measured somewhere in the middle of the canvas, too late to rush about. A few more words about the dimensions: I made the final length of the canvas (mesh) 200 cm. After practical testing, I decided that 180 cm was enough, but I don’t want to unravel the excess.

Problem number 2. As a result, the whole structure turned out to be large - 120cm length of the crossbars, diameter 20cm in a twisted state. In addition, the weight is about 4 kg. Not suitable for hiking. I'll have to give up something, for example, a guitar and beer .. I'm not ready for such sacrifices yet, so now we take a hammock with us only if we get out by transport.

Comment. When weaving a bowline (triangular knots), it must be taken into account that when forming a knot one thread is spent more. A loop for the knot is formed from it. Therefore, it is necessary to alternate the forming thread, change it when weaving a new row. This is difficult to explain: when weaving a row, you need to stick to one knot formation pattern. For example, take the left thread for the loop. Then in the next row for the loop we take the right thread. Everything is clearly visible from the pattern when you are already weaving.

Forest tests.

Despite the problem number 2, a hammock in the forest on vacation is such a BLESS! At least take a queue to lie in it :) By the way, about "lie": I lay down for 30 minutes, without a T-shirt .. Almost no discomfort. As a result, I got the following labels:

Sharp knots are the main disadvantage of the bowline weaving method. But the cells do not scatter and the hammock keeps its shape. If at least put a windbreaker on or lie down in clothes, then in general everything is fine. The height of the hammock is approximately 2 m from the ground. Yes, yes .. I was also surprised until I checked. You need to stretch the canvas strongly, after the first lying down the hammock sags and stays about half a meter from the ground. Our beta tester ventured to spend the night in it. He came to the tent in the middle of the night, said he was cold. Indeed, the grid does not heat up, it does not heat up at all: D

Additions to the article

Addition 1: side rope

how to weave a side rope

how to weave a rope into a net

You need to take into account the following:

• if weaving a rope into a net, then it is imperative to check the dimensions of the cells after tying, so that it does not happen later that the rope collects / stretches the web;
• it is not necessary to weave the rope into the net, as I did on my hammock. You can make it separately, and then pass it through the extreme cells;
• it is desirable to tighten each knot, otherwise the rope will stretch unpredictably under load. In the video, I did not tighten anything, this is a demonstration;
• you can not weave side ropes at all, but simply take a thicker rope. The main thing is that she desired length supported the weight of a man.

Addition 2: Rack

Hanging a hammock is not necessary on trees. Maybe there are no trees in your country villa in the backyard;) Below are several options for hammock stands - we take an example from the Americans. I will not describe the dimensions and technology, because. in the presence of two straight arms, it is not difficult to make such a design.

Addition 3: weaving, rag hammock

According to the search engines, people land on this article when looking for related information about weaving. there is an article on how to do it basketball net, table billiard bag, volleyball net and so on. If for some reason the link is dead, you can download the theme in pdf format.

Again I found on the Internet a pattern of a rag hammock, which I spoke about in the article - download (pdf-format). This is one of many options. Unfortunately, I don't know who the author is.

The hammock is an invention of the South American Indians. It is quite simple to make it, and it is used from not only as furniture for a comfortable sleep, but also as protection against dampness and midges.

Materials for production

The most important thing to consider when making a hammock chair with your own hands is the choice of material. Most durable fabrics

• canvas;
• coarse calico;
• mattress teak;
• camouflage or tarpaulin.

Synthetic products are also suitable for use, but they have one significant drawback - they do not “breathe”.

If we talk about cords, it is better to choose threads made of cotton. Synthetics in this case again loses. Cotton cords are more pleasant to the touch. They are easy to tie into knots and intertwine with each other.

General rules

Regardless of what kind of do-it-yourself hammock chair you are going to make, there are some rules that for all types garden furniture of this type remain the same.

• Hang the product either between two supports or between two trees. If you chose the latter option, the diameter of the tree trunk must be more than 20 centimeters. The deepening of the supports into the ground goes to a meter depth.
• The ropes are taken strong, thick. In diameter, they should reach 8 millimeters. In some cases, the fabric is reinforced with eyelets.
• Install a hammock at a height of one and a half meters above ground level. Between supporting pillars the distance should be up to 3 meters.

DIY hammock (video)

How to make a Mexican cocoon hammock

If you are thinking about how to make a hammock with your own hands, the presented option is one of the easiest. At the same time, it is quite convenient to use it.

When folded, the weight of the hammock is 1 kilogram, so it is convenient to carry it with you. It is almost impossible to fall out of the "cocoon", but in order to get out of the product, you will have to work hard.

To make this type of hammock you will need:

• cord 20 meters long (it can withstand weight up to 200 kilograms);
• dense fabric- 2 pieces of 3 meters.

The assembly goes like this:

• cuts are folded together;
• they are sewn towards each other from two sides, something like a tunnel with unfinished edges should turn out;
• the narrow side of the hammock is tucked a couple of centimeters, stitched;
• resulting tunnel stretch cord;
• then the cord is crossed, tightened so that the fabric is slightly gathered;
• the place of contraction is wrapped several times with a cord, a knot is tied.

Important! In order not to damage the bark of the tree, there should be a cloth at the point of contact between it and the cord. What should a hammock look like? ready-made, you can see in the photo.

wicker hammock

Previously, hammocks resembled an ordinary volleyball net. Now there are many improved options. It is enough to learn the macrame technique and you can independently make a beautiful and comfortable product.

You will need:

• 2 slats - the length should be one and a half meters;
• rope with a diameter of 8 millimeters.

The rope is attached to the bars through specially made holes, whose diameter should be 20 millimeters. The distance between them should reach 5 centimeters. In order for the rope to sit firmly in the holes, the diameter of the latter to it must be made according to the 1/3 principle.

How much cord is needed depends on the pattern chosen. How to calculate the amount of rope required? Measure the distance between the rails, multiply by 3. Then the result should be multiplied by the number of holes.

Important! In the process of use, a hammock made using the macrame technique does not lose its shape.

The technology is simple. It takes 4 ropes to create a knot. Cells must be less than 7 centimeters. Metal rings give additional strength to the structure.

How to fix a hammock (video)

When installing a hammock on supports, the length of the product is adjusted by tension. You can tie it higher, make the deflection stronger.

brazilian hammock

How to make a Brazilian-type hammock with your own hands? You will need:

• nylon linen cord (2 packs of 10 meters each);
• 2 pieces of fabric measuring 90x200 centimeters;
  drill;
• 2 wooden sticks 90 centimeters long.

The assembly of the product consists of several stages.

• Two pieces of fabric are sewn together.

• Then markup is carried out for the eyelets, the distance between them should reach 8.5 cm. Eyelets can be inserted. If they are not, loops are sewn. The cord passes through them, as well as through the eyelets. If possible, it is better to use hardware they are more reliable.
• The sticks must be marked. A distance equal to 2.5 centimeters recedes from the edges. Then 8.5 cm are measured from the marks.

• For an 8 mm cord folded in half, it is required to drill holes with a diameter of 20 millimeters.
• The cord is cut into meter pieces. Each of the pieces is threaded through a hole in the stick. It must be pushed through the grommet, then again through the stick.
• At a distance equal to half a meter from the end of the stick, all the cords are gathered together. It remains only to tie a knot and tighten.

• Next, the knot is braided. The hammock is ready to use! How it looks can be seen in the photo.
• You may also be interested in an article in which we talk about what can be done to give from plastic bottle caps.

Anyone can make their own hammock. It is important to choose the right materials. The cord must be durable, the fabric must be reliable, breathable, made of natural materials.

There are several varieties of hammocks, which one to choose is up to you. If you wish to receive comfortable place for sleep, it is worth stopping at the “cocoon”, if the main thing is aesthetics, you can weave the product using the “macramé” technique. Whichever option you choose, stick with it. general rules for product installation.

Since prices in stores only grow every year, more and more connoisseurs comfortable rest think about how to sew a hammock with your own hands. Woven in fabric or woven using the macrame technique, it will help you relax and enjoy the great outdoors in maximum comfort. And also save a lot of money and pump useful skills in the household.

How to weave a hammock with your own hands at home

1. Durable, pleasant to the touch rope.
2. Two metal rings.
3. Wooden or metal planks about a meter wide.
4. Tools.

Before weaving a hammock out of a rope with our own hands, we will carry out some simple calculations.

• The width of the slats depends on your preferences. Mostly it is made about 1-1.2 m.
• The total length of the rope is calculated as follows. Determine the distance from one bar to another. We add to the obtained value about a meter (on slings). We multiply by 6 (because the “threads” will be doubled when weaving). We estimate how many holes there will be in the bar, and multiply the length calculated in the previous step by this number.

When the calculations are over, we proceed directly to weaving a hammock from a rope.

Step #1. We take the strips and make holes in them at a distance of 5-6 cm from each other. So that the weaving rope does not tear or fray in the future, we process the holes, making them smoother.

Step #2. We cut the rope according to the number of holes in the bar. We take one of the metal rings and fasten the segments folded in half with a loop and a knot on it.

Step #3. We put the ropes through the holes of one of the planks. We check that the distance between the ring and the bar is 50 cm (half the length we laid on the lines). On the opposite side of the ring, we tie the ropes in pairs.

Step number 4. We proceed directly to weaving a hammock. If you own the macrame technique, choose any options for knots and weaves. We advise beginners to stop at a chess pattern.

Step number 5. When you are done with the “hammock body” (make sure that the last row in the cells duplicates the first one), we thread the ends of the ropes into the second bar and fix it with knots on the side outside of the main mesh.

Step number 6. We tie the remaining ends of the ropes on the second metal ring.

Step number 7. To give the hammock the shape of a regular rectangle, we thread the slats through the side holes along the rope. In the middle we twist the ropes with mesh cells, and we also attach the ends to the rings.

The hammock is ready, have a nice rest.

Weave a round hammock: a step by step diagram

Not all connoisseurs of relaxation in nature are suitable for longitudinal forms of a hammock. Some do not have enough space for overall structures, while others prefer to sit rather than lie down during their rest. A round product that can be easily hung in open space and indoors is optimal for such people.

So, to weave a hammock with your own hands at home, you will need:

1. One or two metal hoops of different diameters.
2. Clothesline, nylon cord or other similar material on the hammock itself and on the slings.
3. Cord for wrapping a hoop.
4. Threads, glue and other auxiliary materials.

Step by step diagram:

Step #1. Calculate the length of the cord

The length of the rope depends on a number of factors: the diameter of the hoop, the size of the cells and the desired tension. To calculate it, we do the following:

If you want to change the cell diameter, decrease or increase the number of segments.

Step #2. We wrap one or both hoops with cords

Try to avoid gaps and sagging. We fix the ends with glue, knots, fabric, or any other option that seems reliable to you.

Step #3. Weave a seat.

Based on the previously drawn scheme, we tie several ropes to the hoop and begin to weave. Pay attention, the "green" ropes are folded four times, the red ones are doubled. For clarity in the photo in green the "path" of one "quadruple" rope is highlighted, and in red - one double.

Step 3.1. Making the back

If you want to make a hammock chair from 2 hoops, take a strong tourniquet and fasten the hoops together on one side. We begin to braid the back. It can be the same pattern, it can be different. Only the ends are now attached to the bottom hoop. To add stiffness to the back, fasten 2 straight strips between the hoops and wrap them with a cord.

Step number 4. We fasten the slings

The hammock is ready. To hang it, we tie it to the (upper) hoop of the sling. Then we collect the slings in one knot and or in two (in the manner of a swing) and hang it up. Round wicker hammock is ready.

Note! For example, the simplest version of weaving is taken. If you own macrame technique, then you can use any other solution.

How to sew a hammock for a summer residence with your own hands

Those to whom weaving a hammock with their own hands seems to be something prohibitively complicated can stop at the fabric version. For its manufacture you will need:

• A canvas with a width of at least 1 m.
• Rope or linen cord (at least 8 mm in diameter).
• Sewing and other accessories (for individual options).

When the necessary materials are collected, we proceed directly to the manufacture of a hammock.

Option number 1. Hiking (for lazy people)

This method is considered the easiest, because it allows you to make a hammock step by step in literally 10 minutes.

Step 1. Calculate the length of the canvas. To do this, we determine where the hammock will hang, and measure the distance between the bases (trees, poles). We add another 50 cm to the obtained value and get the length of the desired cut.

Step 2. We collect one edge of the canvas into an accordion, put it in a carabiner and wrap it with a rope so that the structure does not bloom. Repeat for the second edge.

Step 3. We tie ropes to trees, attach carabiners to them. Ready.

Option number 2. Dachny

Such a hammock for a summer residence is suitable for people who are willing to sacrifice personal time for the sake of comfort. Step #1. As in the previous case, we calculate the length of the canvas and cut it out.

Step #2. We prepare the "body" of the hammock. We make a hem on each side and sew it on sewing machine. On the long side - a hem about 10 cm and one seam. On the short one - a hem of about 25 cm and 5 seams with high-strength threads. The distance between the seams is 2.5 - 3 cm.

Step #3. We fasten the rope. We thread the ropes into the resulting holes and tie their ends to the tree. The hammock is ready.

Step #3.1. If you want to add strength structures, the last point can be done differently. When you have completed a large hem and stitched it, insert the straps into the resulting loops and tie the ropes to them.

Step #3.2. To make the hammock as comfortable as possible, we do the following. We cut small pieces from the fabric and fasten them to the canvas in the manner of loops. We string the loops on the bar. We put the hem into the side (along the length) along the rope and also tie them to the bar. With one more (or several) rope we fasten the hammock to the tree. Ready.

Step #3.3. If you are afraid of getting tangled with the lines, wrap them under the ring in a single bundle.

Making a hammock according to one scheme, different people get different results. The point here is not only the directness of the hands, the quality of the materials, but also the little tricks that are not familiar to everyone. For example:

What tricks do you use? Do you know something useful and unusual? Share your experience in the comments, let's discuss.

How to weave a hammock in different forms: photo and video

In the matter of weaving a hammock with your own hands step by step diagram Useful for both the novice and the seasoned master. Therefore, we suggest you look at our collections of photos and videos demonstrating various models and their assembly options.

More interesting on our website: