Comments:

/ /

Installing a bathtub on bricks: a practical way or an anachronism?

As it may seem at first glance, installing a bathtub on bricks is not at all a relic of the total shortage of the past period. On the contrary, even today this “old-fashioned” method is actively used when installing the most modern baths built-in type.

Steel baths

Made from sheet metal by stamping method, steel baths are very light;
Under influence hot water the metal expands and the bottom of the bath bends slightly (2-4 mm);
Due to such temperature fluctuations, the edge of the bathtub moves away from the walls, destroying the laid tiles.

For reference: the included bathtub legs very often do not stand up to criticism. And if the manufacturer supplies its product with strong and stable supports, it will certainly increase the cost of the entire set of plumbing fixtures.

Installation process

So, you purchased a bathtub and delivered it to your home. All that remains is to figure out how to install the bathtub on bricks. And for this you need very little:

Purchase building materials;
Prepare the base of the floor;
Erect supports;
Install a bath.

We agree with this plan of action, we will only add a clause about careful measurements. Traditionally it is believed that height installed bath should not exceed 55-60 cm; accordingly, the height of the bases should take these parameters into account.

Advice: Experienced craftsmen It is advised to apply markings on the floor, which will make it easy to control the process of constructing supports in the future. It can be done with a simple pencil or chalk.

Purchase of building materials

Since steel bathtubs belong to the budget class of plumbing, use simple and commonly available materials to create supports:

Red brick;
Sand-lime brick;
Foam block;
Aerated concrete;
Cinder block, etc.

In addition, you will need cement, sand and water, as well as tools:

Container for mixing the solution;
Trowel (trowel);
Level;
Roulette.

Tip: if you don’t have a trowel, a spatula or even a piece of durable plastic can easily replace it.

Preparing the base

Surely there was or is on the floor of your bathroom ceramic tile. Even if its condition does not cause concern, it still needs to be dismantled at the place where the supports are erected.

Tip: But first, determine exactly where the supports will be installed - just measure on an inverted bathtub from the edge to the support line.

Let's start preparing the base. To do this, arm yourself with a hammer and chisel and:

knock down several tiles;
remove the old solution;
We clean the area from dust and dirt.

Laying process

Let's start building a solid foundation:

mix the solution, adding components at the rate of 3 parts sand, 1 part cement and water until a thick consistency is formed;
apply the solution using a trowel to the prepared base;
install the first brick on the mortar;
tap it so that it is firmly attached to the solution;
lay the next brick in a row and repeat the fastening process;
We take a level in our hands, and while the solution is plastic, we align the horizontal position of the first row of bricks with the level;
apply a new portion of mortar to the laid bricks;
lay out the second row.

Tip: on average, red bricks are laid out in 3-4 rows, silicate bricks - in 2 rows, cinder blocks, foam blocks and aerated concrete - in 1.5 rows. This height of the rows with a bathtub installed on them will be within a comfortable 55-60 cm.

Acrylic bathtubs

Most acrylic models are equipped by manufacturers with steel frames. But their installation is structurally quite complicated, because:

The attachment points of the elements must be drilled;
Some of them are connected by a bathroom only in specially reinforced places. Mistakes lead to cracking of acrylic;
Assembling a bathtub with a hydromassage of an angular or shaft shape takes a lot of time and requires scrupulousness and perseverance.

Moreover, all this does not guarantee the stability and solidity of an acrylic bathtub. Therefore, we can recommend the construction of additional supports, the role of which will be:

Maintaining bathroom wings (especially corner ones);
Formation decorative screen on the basis of a side wall being erected, etc.

In other words, installation acrylic bathtub on bricks — This is not a replacement for the “original” legs, but only an addition to the supports to give the bathroom more stability.

Cast iron baths

If we do not take into account luxury cast iron bathtubs, the cost of which is measured in thousands of dollars, then standard bath built-in cast iron is quite appropriate in modern apartment. Moreover, it only has 4 legs, which are easy to screw on and adjust.

But the masters have serious arguments about this:

The contact patch of the cast iron leg is small (from 2 to 4 sq. dm);
The weight of modern products exceeds 100 kg, and with a volume of 250 liters, each leg accounts for 25% of the weight (almost 90 kg);
To prevent floor deformation, craftsmen suggest erecting brick supports, similar to installing metal bathtubs.

Conclusions: We hope that we were able to clarify the situation regarding bricks in the bathroom. And you do not perceive them as an anachronism, but as one of the effective construction technologies, aimed at improving the stability of the bath.

Modern manufacturers of plumbing fixtures are now increasingly offering shower cabins with many different functions.

But no shower cabin can replace a regular bath, because such a font is universal, you can relax in it and relieve fatigue after a hard day.

Most often, the bathtub is mounted on legs, but it should be remembered that over time the legs of the bathtub become loose and if this is not noticed in time, the bathtub may tip over at the most inopportune moment.

How to ensure greater stability of the bowl? A reliable way to fix the bowl will help with this - installing the bathtub on bricks.

This article explains how to install a bathtub on bricks.

Preparing the room for installation

Preparing the room for installation should be done as carefully as possible. Attention should be paid to the evenness of the floor and check the quality of waterproofing.

If you plan to lay tiles on the floor, it is recommended to use a cement solution to fix the tiles rather than regular tile adhesive.

This is because if the adhesive is applied unevenly, empty areas may form under the tiles.

By installing a bathtub on such tiles you can find unpleasant consequences inattention - cracks, or even broken tiles.

If the wall cladding involves the use of this product, then in this case the tiles are attached to the wall only after the installation of the bathtub is completed.

Why put on bricks

A bathtub on bricks is a method used as often as installing a claw-foot bathtub. What are the advantages of brick supports?

Durability. Although the legs remain stable for quite a long time (approximately 10 years), after this period they begin to loosen. As a result, the bowl itself is deformed, which leads to the fact that water after taking a bath flows down the drain for a very long time. With brick supports such problems never arise.
Versatility. Using brickwork, you can install a bathtub from any material.
Bricks are not subject to corrosion. The legs, in turn, rust over time.
Bricks can withstand intense weight loads. An overweight person may take water procedures without fear of the bathtub tipping over.

Of course, this method also has a drawback - the high cost of installation. It consists of the cost of the brick and the mixture used to prepare the mortar. Usually it is cement - sand mixture.

Necessary materials

Installing a bathtub on bricks with your own hands is not complete without the following materials:

The brick itself. It is recommended to use red brick without voids inside. Bricks should be purchased in quantities of at least 15 pieces.
Cement-sand mixture for preparing mortar.
Specialized tape sealant.
Metal profiles.
Grinder and self-tapping screws (necessary for attaching the bathtub).
Building level.
Special protective rubber gaskets (placed between the bottom of the bathtub and the brick).
Master OK.

We measure sizes

First of all, you need to check the surface on which the bath will be located. If there are gaps and cracks, they need to be cleaned and sealed with cement mortar.

Undoubtedly, it is better to carry out this procedure right away rather than suffer afterwards, fixing the location of the plumbing with the help of boards or any auxiliary materials.

The next step is to take the dimensions of the bathtub. Need to measure:

length and width of the font;
depth of the bathing tank;
distance from the installation site of the supports to the ends of the bath. If difficulties occur when measuring the distance between the rows of bricks, you need to measure a distance of 25 centimeters in both directions from the middle of the bathtub. Brickwork should be located at the resulting points;

According to the rules, when measuring the dimensions of the bowl, it is necessary to take into account that the height of the bathtub from the floor should reach 55 - 70 centimeters.

Determining the required height is simple - you need to understand how it will be most convenient for home owners to take water treatments directly and choose the result obtained.

It is also necessary to remember that there is no need to form a slope of the font towards the drain hole, since modern baths already equipped with a slope at the factory.

How to place it in the room

When planning the location of the font, you must remember that it should fit as closely as possible to the wall.

If this condition is not met and there is no specific treatment between the bathtub and the wall, fungus and mold will multiply very quickly, and this will cause great inconvenience.

Talking about end walls It should be noted that between them and the bathroom, on the contrary, there should be a small gap, which after installation simply needs to be treated with sealant.

Such a gap must be present in case of overheating or expansion of the bath. In such cases, if the end sides fit tightly to the wall, it may become deformed.

You need to check the container for slope. If it is still missing, you need to make racks of different heights.

The slope must be made towards draining the water so that it does not linger in the bowl after water procedures.

Installation of supports

After all measurements, you can begin preparing cement - sand mortar, and then to the manufacture of supports.

The standard mixture looks like this - one part of cement is mixed with four parts of sand, with the addition of large quantity water.

There are several types of brick supports:

Columns. Universal and most commonly used method. Making brick posts requires much less material than in other cases, so this method can be considered economical. However, such supports are more suitable for installation cast iron bath. The bottom of a cast iron bowl does not need support, since, unlike bathtubs made of steel or acrylic, it cannot deform under intense weight loads.
Podium. This method is just right for acrylic and steel bathtubs. The essence of the method is that a backing made of bricks is located under the bottom of the bathtub, repeating its shape. This type of masonry helps to evenly distribute the load on the bowl, preventing it from deforming. The disadvantage of the podium is the use of a large number of bricks, which leads to significant financial costs.
Perimeter supports. Such supports are installed in conjunction with standard legs. It turns out that the legs support the bottom of the bathtub, and the brick supports support the edges of the bathtub. The method is certainly useful, but if you do not leave a special window in advance, servicing the communication system may be difficult.

The shape of the supports also depends on the shape of the bathing container itself:

rectangular. Such models usually have rounded edges;
triangular. Required for corner bath;
oval;
beveled;

It is important to remember that you do not need to install the bath directly on brickwork. It is recommended that you first install a siphon with an overflow on the bathtub and only then fix the bowl to the bricks.

Bathroom installation

All actions must be carried out with the utmost care, coordinating them with your partner.

On initial stage A protective rubber gasket will come in handy. First of all, it needs to be placed on brick supports.

In the case when the bathtub is classic, it is lowered to its bottom building level. Next, you need to take it from both sides and slowly level it. If the bottom of the bathtub is of a non-standard shape, the level is applied from the outside.

The next stage is testing the bathtub for strength. To perform the test, you need to grab the edge of the bathtub and perform an action as if the bowl needs to be rocked. The slightest movement means the structure is unstable.

In this case, everything needs to be carefully inspected and the shortcomings eliminated.

After checking the bathtub and eliminating any shortcomings, if any, you can additionally fix the bowl using metal profiles, grinders and self-tapping screws.

Rigid fixation and installation of the pipe

In the case when it is necessary to install an acrylic bathtub, the choice should be made on a podium made of bricks and additional brick racks installed around the perimeter of the bowl.

If you choose a steel bathtub for your bathroom, it is recommended to add additional supports to it for greater strength. These can be brick racks or piers. Which one should I choose?

The answer is simple - if the bathtub is surrounded by walls on three sides, racks are suitable, since such a bowl is quite stable. If the bathtub is in contact with only one side of the wall, then a wall is suitable in this situation.

After the bowl is completely fixed, you can begin installing the pipe. This requires a 90 degree pipe and a 45 degree elbow.

These elements must be made of plastic. Unite plastic corrugation and the sewer exit is recommended to be done carefully, slowly.

All elements must fit tightly to each other, ensuring the necessary tightness. To do this, all joints must be treated with sealant and allowed to dry completely.

After the sealant has dried, it is necessary to check it. You need to fill the bathtub with water, open the water drain and watch how the water leaves the bathtub.

Ideally, water should flow out of the bath freely, and joints and joints should not leak. All these actions are carried out several more times, then the structure must be allowed to rest for a day and this check must be carried out again.

After reading this article, we can conclude that you can install a bathtub on brick supports yourself, using a small set of tools and materials.

Having completed all the described steps, you can safely take water procedures without thinking about how stable the bath is. And the knowledge that all the work was done with your own hands increases the pleasure of the process.

You can install a bathtub in your house or apartment different ways. Each of them has its own advantages and disadvantages. The most popular method is to install the bathtub on bricks. Experts consider the positive aspects of installing this plumbing equipment in this way to be its stability and improvement. That is why, before choosing any of the options, it is worth analyzing all the features and nuances of the work in each specific case.

Installing a bathtub on acrylic bricks

An activity such as installing an acrylic bathtub on bricks involves the use of a completely standard set of materials and tools. These include a hammer, screws, bricks, cement mortar, rags, tape sealant, metallic profile and polyurethane foam for s/t devices. Once everything you need has been purchased and prepared, you can begin to work.

Laying bricks

Directly on the floor in the place where the bathtub will stand, you should begin to lay brickwork in the form of low supports. There are several important factors to consider:

the distance from the floor to the edge of the bath should be no more than 60 cm;
the slope towards the bathtub drain should be about 2 centimeters;
the distance between the supports should be about 50-60 cm.

The dimensions of the brick supports should be calculated based on the size of the bathtub itself. Due to the fact that they can be completely diverse, it is impossible to give any universal advice on this matter.

Bath installation

Installing an acrylic bathtub on bricks with your own hands is quite simple. This is primarily due to the fact that its weight is not very large. There are two possible types of installation:

Installation directly onto the bricks themselves without the use of feet.
Combined installation, which involves using not only bricks as support, but also the included legs.

In the second case, you must first install the bathtub along with the legs, and then measure all the distances that these elements occupy. Taking this into account, it is worthwhile to additionally equip the brickwork itself.

You should not use foam as a sound-absorbing agent for acrylic bathtubs, since they do not make too loud sounds when filled with water.

It is worth remembering that under no circumstances should you install a bathtub on brickwork that has not yet dried. It is also important to consider that between the building material and the container itself there must be either a cement pad or sealing foam.

Sealing cracks and gaps

Do-it-yourself installation also involves the use of foam and tile adhesive. These materials should be used in places where there are any cracks or gaps between the bathroom and other elements of the interior of the room.

The joints between the tiles and the container should be sealed using tape sealant. It's best if he is white. If such material is not available, you should use construction silicone. This will completely cover even the smallest cracks. The advantage of using such material is that it is transparent.

Installation of a cast iron bath

They differ in significant weight. Unlike acrylic products, they can have a very significant mass, so their installation is quite labor-intensive and complex. In addition, such bathtubs make noise when filled with water, which must be taken into account when installing them. Wherein similar products have a lot of advantages, such as accessibility, long-term heat retention, etc.

Due to the large weight of cast iron bathtubs, their legs often break during use. Therefore, many experts recommend immediately placing these products on reliable brick supports. In this case, there is no need to worry about any breakdowns.

Preparatory work

Installing a cast iron bathtub on bricks should begin with certain preparatory work. First of all, this concerns the introduction of these products into the premises. They can significantly damage door openings and walls. Because of this, it is best to first cast iron bath wrap with materials that can serve as softening seals.

To make it more convenient to connect the siphon in the room where the bathtub will be installed, place the container on one side. In this case, it is very important to use waterproofing in the form of a gasket under the drain ring. This can prevent the possibility of water leaking onto the floor.

For a more reliable installation of a cast-iron bathtub, this process should be done using a combined method - with the installation of legs and brick supports.

Carrying out brickwork

It is best to do brickwork along the entire length of a cast iron bathtub. This will directly affect the strength of this structure. Sand-cement mortar should be used in the following preparation:

1 part binder - cement;
4 parts filler - sand.

The height of the bathtub together with the supports should not exceed 60-70 centimeters. Thus, it will be necessary to use no more than 20-30 bricks. If you make supports around the entire perimeter, the material consumption will be more significant.

It is also necessary to provide for a slope. Just 2 centimeters is enough. Most often, one support is made 19 centimeters high and the other 17 centimeters high.

If you use brick around the perimeter of the bathtub, it is best to first mark with chalk the locations of legs, pores, etc. This can significantly simplify the work and eliminate errors in measurements.

After installing the bath on it, the brickwork can be additionally coated with fresh mortar. This slightly improves its strength characteristics and stability.

Additional equipment

Cast iron bathtubs make significant noise when filling them with water. Therefore, experts recommend treating the outer surface of these products polyurethane foam. It will absorb sounds and make the use of the bath more comfortable.

You should apply foam to the bath before it is placed on the brickwork. It is also worth noting that there should be a layer on top between the supports and the container. It can be done either using cement-sand mortar or using the same polyurethane foam.

The outer edge of the bathtub should exceed the level of the part located near the wall by 0.5-1 centimeter. This will prevent water that gets on the wall of the container from overflowing.

The cast iron bathtub should be seated on foam that has not yet dried, located on supports. In this case, it is worth using a building level to monitor how smoothly it is done.

The part of the cast-iron bathtub that is located under the wall must be sealed using tile adhesive. On top of it you can additionally use silicone sealant. This will prevent pores and cracks that may form in the material. Other joints can also be treated in a similar way.

Conclusion

Correct installation is the key to long-term use of the container, as well as preventing unfavorable situations and breakdowns. That is why implement this action stands as carefully and correctly as possible. In the future this could be very important important role.

Installing a bathtub on bricks is a process that is both troublesome and simple. It can easily be mastered by a non-specialist who has basic skills in working with bricks.

Most bathtubs have metal legs included, but craftsmen assure that a bathtub on a brick base will last much longer, thanks to a more reliable fastening.

You can place the bathtub where it should perform its functions different ways. Their choice depends on the type and area of the room, whether it is combined with a bathroom, the size and shape of the bath itself, and the presence of objects in the room that limit maneuverability.

Installing a bathtub on legs does not guarantee its stability, since the fastenings become loose over time, requiring repairs. One of the most reliable ways is to install the bathtub on bricks. Its advantages are as follows:

increasing the service life of the product;
greater stability;
increased strength;
the possibility of increasing the load on plumbing;
reducing the likelihood of emergency situations.

A brick pedestal, built according to all the rules of the art of construction, is a good basis not only for monuments, but also for a wonderful plumbing device. The brick bath itself is an original structure.

Bath masonry options

Masonry under the bathtub can be different. It depends on the specifics of the room, the characteristics of the bath, production needs, capabilities and imagination of the person. Summarizing all this diversity, we can highlight the following most popular options:

Two supports in the form of small walls supporting the bathtub. They are usually made with a concavity at the top to match the shape of the vessel.
A solid pedestal supporting the entire base of the bathtub.
Construction of a brick wall along the edges of the bathtub. Most often, such a structure is erected when installing a corner acrylic bathtub.

There is no fundamental difference in the technology for forming these masonry. The differences are only in quantity building material and labor expended.

Installing a bathtub on bricks: algorithm of actions

Before starting laying, it is necessary to take all measurements. This should be done in order to understand how to optimally place the sanitary container. Further work is carried out in stages:

In the area allocated for the bathroom, it is necessary to lay brick racks so that a bathtub can be installed on them without the risk of it slipping. The racks must be placed so that there is a distance between them that falls within the range of 50 to 60 cm.
After the brickwork has dried, the process of installing the product itself begins. Installing an acrylic bathtub on bricks is the least complicated and time-consuming. The lightness of this product facilitates the installation process, but does not reduce the requirements for the quality and size of the masonry, since the peculiarities of operating the product with water and a person placed in it should always be taken into account.

There are only 2 types of installation of products - with and without legs.

In the first version, the bathtub rests both on a brick pedestal and on legs corresponding to the model of the product. In the second, the plumbing object lies entirely on the brickwork.

Typically, a combined option with bricks and legs is chosen for heavy objects. Sometimes brick supports are formed after the bathtub has been installed on legs and has been in use for some time.

Before you install steel bath on the legs, with the combined option, you must first secure them completely, then measure the height between the floor surface and the bottom of the product, as well as the distance between the legs. This will allow you to correctly calculate the number of bricks for masonry.

The choice of a combined option is sometimes due to aesthetic considerations. When the bathtub stands on legs, and the bricks only help it to hold firmly, the design looks more elegant.

//www.youtube.com/watch?v=u2mwScppEJg

Before installing the bathtub on the bricks, you need to apply polyurethane foam on top of them when they are dry. After this, we install the bath on the still fresh foam. To make seating on the foam faster and more reliably, it is necessary to fill the bathtub with water and place a mounting level on its edge. This is necessary in order to track the developing slope as the foam shrinks.

After the bricks are laid with your own hands, the bathtub is installed and properly leveled, it is time to seal the cracks and correct what was done with flaws. To enhance the adhesion of the bottom surface of the bath to the solution, polyurethane foam is usually used. It can also be used to seal cracks. If desired, they can be sealed cement mortar With tile adhesive.

The joints between the bathtub and the wall are sealed with tape sealant. For this purpose, you can use plumbing silicone, which well masks all irregularities, holes and cracks.

Sealing is necessary not only to prevent water from entering the space outside the bathtub, but also, above all, to ensure that moisture does not enter the area of \u200b\u200bthe brickwork and construction foam.

Subtleties and details of the process

The described process is simple, but you need to know some of its features:

The top of the bath should not be higher than 60 cm from the floor surface.
Should be paid Special attention the angle and direction of tilt at which the object will be placed. This is necessary in order to correctly calculate the placement of sewer pipes. Mistakes in this matter will lead to problems with draining water. Usually the difference between the height of the sides is 2 cm.
When forming a pedestal, you need to take into account not only the size and configuration of the bathtub, but also the material from which it is made. The most problems are caused by cast iron and hardware. They are heavy, which puts stress on the brick base.
You should not install the bathtub immediately after you have completed the construction of the brick support. First you need to dry it all.
Sometimes construction foam cover not only the brick base, but also the outer surface of the bathtub. This is done for better sound insulation. It is not necessary to cover the entire acrylic bathtub with foam, because it itself absorbs sound well.
You can adjust the angle of inclination using pieces of bricks and cement mortar. If you are working with an acrylic bathtub, you need to ensure that sharp corners the brick fragments did not puncture it.

//www.youtube.com/watch?v=VFUs1_1ZrjE

Despite its simplicity, this matter has many nuances. But you can handle everything if you follow the tips for installing a bathtub.

When buying a bathtub, you need to immediately think about its installation, and what it will stand on: on factory legs or bricks. Some will prefer the first option, and when installing the bathtub it will turn out that the bathtub on them is unable to take the correct horizontal position and will be unstable, so the second type of support is the most practical, so we will consider it further.

Installing a cast iron bathtub on brick supports

Before installation, you need to free up space near the bathroom and carefully take measurements. Since a cast iron product is not lightweight, it is worth accurately determining its location, and to protect the door jambs, which may be damaged when bringing the bath in, it is necessary to wrap them soft cloth, securing it with staples from a construction gun.

Before carrying out the installation procedure, you should prepare two dozen red bricks, a container for mixing cement mortar, a trowel and a trowel. The planned installation is not difficult, but it is difficult to redo it due to the large mass of the bathtub, so you should be prepared for the correct installation and strictly follow the tips described below.

Bathtub installation algorithm:

Bring cast iron into the bathroom . Install the legs supplied with it.
Assemble the siphon . Check the correctness and reliability of its installation.
Blow out the bottom with foam . This is necessary if you want to make the bath sound-absorbing. Only when applying foam, you need to make sure that its layer does not protrude from behind the shoulder of the cast iron product, otherwise it will not fit tightly against the wall.
Take measurements of the bathtub dimensions . To accurately make brick supports, measure the distance from the bottom of the product to the end of the legs. You also need to find out the size between the legs; this parameter with an allowance of 10 mm will correspond to the size of the brickwork.
Install the bathtub to the wall . This preliminary installation, in which you need to place it close to the wall, and adjust the slope of the front and rear sides so that the front part is higher than the one located against the wall, this will prevent water from flowing out of the bath. Then it needs to be taken out.
Mix sand-cement mortar . The optimal ratio for its preparation is a mixture of 4 parts quartz sand and 1 part 400 grade cement. At the end, water is added to them, the amount of which is determined by the state of the mixture. It is better to start with small portions and then add more as needed. If the solution turns out to be watery, then cement should be added to it. For a more durable composition, half of the solution can be replaced with tile adhesive, due to this it will become more plastic.
Lay the supports . We must not forget about the deviation to the side back wall. Half a brick must be laid on each edge of the masonry. After this, the brick structure is left to stand for 24-48 hours to allow the cement mixture to harden.
Carry out final installation. A layer of mortar should be laid on the top of the bricks; on the central support it should be no more than 2 cm; a small recess should be made in it, repeating the shape of the bottom. It is necessary to apply tile adhesive to the bathtub collars that are adjacent to the wall, lubricating the same places on the wall itself. Place the bathtub on brick supports and press it firmly against the wall.
Carry out installation control . You need to check the slope of the bathtub, and if necessary, adjust it using the legs or by placing additional pieces of brick between the supports and the bottom, and if there are cracks in these places, they need to be sealed with mortar. If polyurethane foam is applied on one side, it must be blown out on the other side as well. front side, taking into account the size up to the collar, and not exceeding it.

After installing the bathtub, you need to check the operation of the siphon: fill the bathtub with a small amount of water and open the drain; if nothing leaks, then everything is fine.

If the bathtub will be installed on bricks without legs, then you should not overestimate its location. Optimal height is 70 cm, but in most cases installation occurs at 60 cm; it is not advisable to install it higher, since it will be inconvenient to climb into it.

Installation on a brick frame of an acrylic bathtub

The low weight of such a product can give a false impression, because in comparison with its cast-iron counterpart it is fluffy and it seems that reinforcing the supports in the form of brickwork is unnecessary. But this is a wrong opinion.

Firstly, a bathtub filled with water, no matter what material it is made of, weighs quite a lot, and its legs, unable to withstand such weight, move apart. Secondly, they rust over time and can easily crumble, which causes problems with the misalignment of the bathtub, and this affects the drainage of water - it stagnates in the drain hole. There are cases where acrylic bathtubs burst under the weight of a large volume of water. Based on this, it becomes clear that brick supports must be installed under such products in order to extend their service life.

Acrylic bathtubs can be of different shapes: oval, rectangular with rounded edges, triangular and beveled, but the principle of installing brick supports remains the same for everyone. The main thing is to adjust them to the bottom of the chosen acrylic product. The optimal solution for increasing the strength of an acrylic product would be to install a frame, which can be done in conjunction with the brickwork of the supports.

Algorithm installation work is:

Prepare the room and materials . Cover the walls with the selected material, select bricks and cover them with roll guerlain. This material contains a fabric layer that serves as a separator between the cement mortar and the wall. This kind of compensator can change its shape and geometry when the water temperature changes.
Attach installation hooks to the wall . They are in construction stores, and if desired and available the required material(steel plates) such parts can be made independently. They are hooked onto the side of the bathtub adjacent to the wall.
Install brick supports . It is performed in the same way as for the previous type of bathtub. You can make not two, but three supports. Their height and the order of laying are carried out according to the previously described option.
Execution of the frame . Some craftsmen make a frame from corners, but it is not as strong as brick version, during the creation of which a kind of niche is laid out from a quarter of a brick. Only between the wall and the bathroom you need to provide a centimeter gap. Flat design along the entire perimeter of the bath will create reliable protection walls of the product, you just need to take into account the implementation of the service window. If this is not done, then if necessary, check the siphon and sewer pipes, hidden under the bathtub, you will have to dismantle all the brickwork. If there are not enough bricks, then you can limit yourself to supports only at the corners of the bathtub.
Seal the gaps between the bathtub and the wall . Polyurethane foam, silicone tape or sealant will help.

An acrylic bathtub can be installed first on the legs, fixing them in the created cement bed, and then strengthening them with brick supports, which are placed between the legs and in the middle of the bottom.

How to install a steel bathtub on brick supports? + video instructions

The legs welded to the bathtub, due to their unreliable design, do not create a stable position. This video shows how to fix a bathtub using bricks so that it takes up correct location and became rigidly fixed.

Due to the instability of the bathtub, it is impossible to create a border between it and the wall - it is constantly being destroyed. To eliminate these problems, you can use ordinary red bricks and construction glue. The progress of the work is as follows:

Raise the bath . For ease of installation, you can use a jack and raise it to the desired height. The standard height to the bottom of the bathtub is 60 cm, that is, you need to be guided by this size. But on different models bathtubs, their depth varies by several centimeters, so before major installation it is worth carefully measuring everything out.
Lay out brick racks . There will be two of them. You need to retreat the same distance from both edges of the bath and mark on the floor where the bricks will be installed. The first of them needs to be installed with the smaller side flush against the wall, after having previously lubricated its lower part with tile adhesive. Then lay the next brick butt to it. That is, the racks are made of half a brick. The height turned out to be three bricks lying on top of each other.
Bath installation . Tile adhesive is applied to the surface of the topmost brick. Then the jack is lowered and the bathtub is fixed on the bricks. The legs of the bathtub also need to be glued to create more reliable supports.
Fill up the empty space between the wall and the bathtub . For large gaps, you can cut a narrow strip of foam and install it using regular sealant. Where the distance to the wall is small, simply seal it with sealant.

A steel bathtub is very noisy; with high pressure, the roar of water hitting it can be heard throughout the house. To prevent this, during installation you need to cover its bottom with any sound-absorbing material or apply polyurethane foam to it.

The considered options for installing a bathtub on brick supports guarantee long term service life of the product, they enhance its strength, and when using polyurethane foam, they increase noise absorption. You don’t need any special skill to create them, so installing bathtubs is easy to do yourself. You can learn about other installation nuances from.