Today we will tell you about the cyclone filter for a vacuum cleaner in the workshop, because one of the problems that you have to deal with in woodworking is dust removal. Industrial equipment quite expensive, so we will make a cyclone with our own hands - it's completely simple.
What is a cyclone and why is it needed
In the workshop, there is almost always a need to remove garbage of a sufficiently large fraction. Sawdust, small scraps, metal shavings - all this, in principle, can be caught by a regular vacuum cleaner filter, but with a high probability it will quickly become unusable. In addition, there will be no superfluous opportunity to clean and liquid waste.
The cyclone filter uses an aerodynamic swirl to bind the specks different sizes. Spinning in a circle, the garbage manages to stick together to such a consistency that it can no longer be carried away by the air flow and settles at the bottom. This effect almost always occurs if the air flow passes through a cylindrical container at a sufficient speed.
Such filters are included in the kit of many industrial vacuum cleaners, but their cost cannot be called affordable for the layman. At the same time, the range of problems solved with the help of homemade devices, not at all anymore. A handicraft cyclone can be used both in conjunction with planers, perforators or jigsaws, and for removing sawdust or chips from different kind machine tools. In the end, even simple cleaning with such a device is much easier, because the bulk of dust and debris settles in a container, from where it can be easily removed.
Difference Between Wet and Dry Cyclone
To create a swirling flow, the main requirement is that the air entering the tank does not follow the shortest path to the exhaust port. To do this, the inlet pipe must have a special shape and be directed either to the bottom of the tank or tangentially to the walls. exhaust channel according to a similar principle, it is recommended to make it swivel, optimally if it is directed to the cover of the device. The increase in aerodynamic drag due to pipe bends can be neglected.
As already mentioned, cyclonic filter potentially capable of removing liquid waste. With a liquid, everything is somewhat more complicated: the air in the pipe and the cyclone is partially rarefied, which contributes to the evaporation of moisture and its breakdown into very small drops. Therefore, the inlet pipe must be located as close as possible to the surface of the water or even lowered under it.
In most washing vacuum cleaners, air is supplied to the water through a diffuser, so any moisture contained in it is effectively dissolved. However, for greater versatility the minimum amount alterations to use such a scheme is not recommended.
We make from improvised materials
The most simple and affordable option for the capacity of the cyclone there will be a bucket of paint or other building mixtures. The volume should be comparable to the power of the vacuum cleaner used, approximately one liter for every 80-100 watts.
The bucket lid must be intact and hermetically put on the body of the future cyclone. It will have to be finalized by making a couple of holes. Regardless of the material of the bucket, the easiest way to make holes of the desired diameter is to use homemade compasses. IN wooden lath you need to screw in two self-tapping screws so that their tips are at a distance of 27 mm from each other, no more, no less.
The centers of the holes should be marked 40 mm from the edge of the cover, it is desirable that they be as far apart as possible. Both metal and plastic scratch excellently in this way. homemade tool, forming even edges with virtually no scoring.
The second element of the cyclone will be a set of sewer elbows at 90º and 45º. In advance, we draw your attention to the fact that the position of the corners must correspond to the direction of air flow. Their fastening in the housing cover is carried out according to the following scheme:
- The knee is inserted all the way into the side of the socket. Silicone sealant is pre-applied under the side.
- WITH reverse side a rubber o-ring is pulled onto the socket with force. To be sure, you can additionally compress it with a screw clamp.
The inlet pipe is located with a narrow turning part inside the bucket, the socket is on the outside almost flush with the lid. The knee must be provided with another turn at 45º and directed obliquely down and tangentially to the wall of the bucket. If the cyclone is made with the expectation of wet cleaning, the extreme elbow should be increased by cutting the pipe, reducing the distance from the bottom to 10-15 cm.
The exhaust pipe is located in the opposite position and its socket is located under the bucket lid. You also need to insert one knee into it so that the air intake occurs at the wall or make two turns for suction from under the center of the lid. The latter is preferable. Do not forget about the o-rings, for more reliable fixation and to prevent turning of the knees, they can be wrapped with plumbing tape.
How to adapt the device for machines and tools
To be able to draw in waste when working with hand and stationary tools, a system of adapters is required. Typically, a vacuum cleaner hose ends in a curved tube, the diameter of which is comparable to the nozzles for power tool dust bags. IN last resort, you can seal the connection with several layers of double-sided tape for mirrors, wrapped with vinyl tape to eliminate stickiness.
With stationary equipment, everything is more complicated. Dust vents have a very different configuration, especially for homemade machines, so we can only give a few useful recommendations:
- If the dust extraction of the machine is designed for a 110 mm or larger hose, use plumbing adapters with a diameter of 50 mm to connect the corrugated hose of the vacuum cleaner.
- For docking with a dust trap of home-made machines, it is convenient to use press fittings for 50 mm HDPE pipes.
- When designing the dust collector cover and outlet, use the convection current created by the moving parts of the tool to greater efficiency. For example: a branch pipe for removing sawdust from circular saw must be tangential to the saw blade.
- Sometimes it is required to provide dust extraction from different sides of the workpiece, for example, for band saw or a cutter. Use 50 mm sewer tees and corrugated drain hoses.
Which vacuum cleaner and connection system to use
Usually a vacuum cleaner makeshift cyclone do not choose independently, but use the one that is available. However, there are a number of limitations in addition to the power mentioned above. If you want to continue using the vacuum cleaner for domestic purposes, then at a minimum you will need to find an additional hose.
The beauty of the sewer elbows used in the design is that they ideally fit the diameter of the most common hoses. Therefore, the spare hose can be safely cut into 2/3 and 1/3, a shorter segment must be joined to the vacuum cleaner. The other, longer section, in this form, is refueled into the socket of the cyclone inlet pipe. The maximum that is required in this place is to seal the connection silicone sealant or sanitary duct tape, but usually the planting density is quite high. Especially with the o-ring.
In the video, another example of the manufacture of a cyclone for dust removal in the workshop
To pull a short piece of hose onto the exhaust pipe, the extreme part of the corrugated pipe will have to be leveled. Depending on the diameter of the hose, it may be more convenient to tuck it in. If the straightened edge does not fit slightly on the pipe, it is recommended to warm it up a little with a hair dryer or an indirect flame. gas burner. The latter is considered an excellent option, because this way the connection will be located optimally in relation to the direction of the moving stream.
Large garbage in the workshop can always be swept away and taken to a landfill in bags. But what about dust, metal or wood shavings, and numerous other microscopic waste products? Buying can be a good hit on the wallet. A regular vacuum cleaner can't do the job. But if you make a cyclone for a vacuum cleaner with your own hands or even your own construction vacuum cleaner, you can save yourself a number of problems!
Why do you need a cyclone filter?
Construction, metal or wood dust is completely harmless in appearance. But this is only at first glance. Working in a dusty environment can harm the respiratory system and cause serious illness. Yes, and the tools will deteriorate from the endless stream of garbage. There may be several reasons:
- Dust gets into the tool and onto the lubricant inside it. As a result, it overheats and fails.
- If the device has moving parts, then dust may well impede their operation, and also lead to breakage in the future.
- Dust can clog special ventilation holes, which are designed to cool the tool. As a result - again overheating and breakdown.
The cyclone filter will ensure the collection of any debris in the workplace without harm to the vacuum cleaner.
Principle of operation
Using the aerodynamic air flow, the filter will bind the dust particles together. In turn, centrifugal force begins to act, pressing them against the walls of the container. And then gravity causes the debris to settle to the bottom.
There are many diagrams showing the operation of cyclone filters. One of them can be seen below.
Cyclone filter device
You can make such, or a similar filter yourself. There are a huge number of options for execution, but one thing unites them - the principle of operation. Any design will consist of:
- A conventional vacuum cleaner (preferably powerful);
- cyclone filter;
- Containers that collect garbage.
throughout the structure. In normal condition, it is designed for cleaning the house, suction of small debris and dust. In this case, a cyclone filter appears, which means that the length of the duct will be increased by almost three times, respectively, and the load on the device will be greater. The design turns out to be quite massive, unlike a conventional vacuum cleaner, so such a trick is necessary to ensure that the length of the hose is enough for comfortable cleaning.
Do-it-yourself construction vacuum cleaner: what you need
As mentioned above, you can use a regular household vacuum cleaner. But this option does not attract many masters, therefore best solution becomes a do-it-yourself unit.
In order to make such a device, even if it has been preserved since the time of the distant Soviet past. This is the advantage that homemade vacuum cleaners can be made from unnecessary old units.
So, from the vacuum cleaner we extract such elements as:
- Motor;
- Cord connecting the device to the network;
- Power adjustment device;
- Suction corrugation.
Prepare for the body:
- A plastic pipe with a diameter of 5 cm;
- Container with lid;
- A sheet of plywood about 0.5 cm thick;
- 14 nuts and bolts M6;
- Galvanized sheet metal strip;
- Car filter (from a minibus);
- Switch - 220 V;
- sealant;
- Sandpaper;
- Glue gun rods;
- Corrugated hose (possible from a washing machine);
- Threaded stud with nuts and washers;
- Wiring corrugation PND32.
It is worth immediately preparing the tools:
- Drill;
- Glue gun;
- Sealant gun;
- Locksmith keys;
- Screwdrivers;
- Electric jigsaw;
- Wire cutters.
Manufacturing
At about a distance of 10 centimeters from the top of the container, we make a hole into which we connect the pipe. The hole should be an oval even shape. The branch pipe is placed in it slightly at an angle downwards, tightly adhering to the wall. glue gun you need to fix the result, as in image 2.
A pipe inserted into a pre-drilled hole in a barrel
From the inside we fasten the adapter to connect the suction hose.
We cut out two circles about half the size of the cover, drill holes for the bolts. Parts are attached on both sides. After other circles are drilled, and with sandpaper, their surface is cleaned of burrs. We cover the products around the perimeter with sealant, after that, they are installed and finally fixed. The hole for the pin is made in the center. A little to the left there will be a larger hole for air intake.
Location of stud and air outlet
We will need an air filter without a mesh (it will be clogged with debris, which is extremely unprofitable) in which it is placed. It must be removed with clippers. One side of the cylinder should be closed with a plywood plug. The filter is attached to the stud with a nut.
By the way, the filter will help not only get rid of dust, but also prevent the inhalation of dangerous small particles, such as toner. If you use a conventional vacuum cleaner in this case, the bags are easily clogged with toner dust. In this case, all particles will settle in the collection container.
In order to make it more convenient to mount, it can be cut out along with the plastic parts. To fix it on the lid, you will need a clamp, which can be made from a strip of tin.
The switch and regulator are placed side by side. After that, all parts are connected to each other with wires, and a wire with a plug is connected.
Make sure that everything is connected correctly and there are no bare wires, and only after that check the operation of the device.
Location of motor, switch and power regulator
The length of the suction hose is usually not enough, so it is extended with a corrugated pipe.
Standard nozzles from a vacuum cleaner will help to put things in order in any workshop. They can also be used to connect to equipment, for direct garbage collection, using simple adapters.
So, a home-made cyclone-type construction vacuum cleaner is ready!
What to do if there is no way to make a vacuum cleaner with your own hands?
Of course, not everyone wants to make a vacuum cleaner from scratch, and necessary details may not be. In this case, a regular household vacuum cleaner is perfect, better with big power. Next, you just need to make a cyclone filter for it, which will not require large expenditures. Most often it is made from a traffic cone or bucket. Let's consider both options.
A drawing of a homemade cyclone can be seen below.
Cyclone drawing
Road cone cyclone
Simple and fast way to build a cyclone on a vacuum cleaner directly with your own hands is to make it from a traffic cone.
What is needed for work?
Since the manufacture of the cyclone will be carried out with my own hands need to prepare necessary tools And Consumables. So we are preparing:
- traffic cone;
- Plastic pipes (about 40 mm)
- 45 degree angle;
- Plywood;
- Pieces of chipboard;
- Glue gun and rods;
- A container with a lid, it is possible from under the paint.
Let's start manufacturing
To begin with, we take plywood to make a cover from it that closes the cone. We cut out a circle of the desired diameter, and cut two holes in it. One will be in the middle, the second parallel at the edge, as in Figure 6.
Plywood circle with holes for air inlet and outlet
Pipe inserted into one of the holes
It is also necessary to insert a pipe into the second hole, but a 45-degree angle is put on top of it. It is moving along it that the air will twist into a whirlwind. The angle is inside the cone.
Corner location for proper air circulation in the cyclone
After the pipe is glued as in the case of the first. The lid is ready. Then it is glued into a cone.
The tip of the cone must be cut off. After, it is inserted into the bucket lid in the center into a pre-prepared hole. The place of attachment is glued. WITH inside the cover must be reinforced with pieces of chipboard. After they are pulled together with self-tapping screws.
The result is a product as in Figure 9.
Ready product
Bucket cyclone filter
Another simple material for the manufacture of a cyclone filter, an ordinary bucket will become, you can even use paint. The volume must be calculated based on the power of the vacuum cleaner - this is approximately 1 liter of capacity for every 80-100W.
The bucket must have a hermetically sealed lid, and the shape of the container itself must be round!
For manufacturing you will need:
- A bucket with a lid (can be from under construction mixtures);
- Compass;
- 2 knees 90 and 45 degrees;
- plastic pipe;
- Silicone;
- Rubber or o-rings;
- Stationery knife;
- Glue gun.
Manufacturing
We make holes in the lid. You can use a factory compass, or you can make a homemade one. Screw two self-tapping screws into the wooden rail at a distance of exactly 2.7 centimeters from each other.
The center of each hole is marked 4 cm from the edge. Next, circles are cut out for pipes at the marked places.
We insert the knee tightly into the socket, having previously applied silicone to its side. From the inside of the product, a sealant is pulled onto the socket. If necessary, crimp with a clamp. It will turn out as in Figure 10.
We insert the pipes into the bucket lid, turning the corner correctly
From the outside, the inlet pipe is almost flush with the cover. On the reverse side, the knee is directed by the rotary part to the center of the bucket. But for desired effect it is provided with a 45 degree turn, which is directed obliquely down as in Figure 11.
View from the back
The second branch pipe, which will draw air, is located in the opposite direction. A knee is inserted into it so that air is taken from the wall of the bucket. O-rings must be used in each case, they will securely fasten the pipes and prevent them from turning.
We conclude that you can make a cyclone for a vacuum cleaner with your own hands quickly and easily, using improvised means. At the output, you should get approximately the same device as in the figure below.
Cyclone filter connected to a household vacuum cleaner
Difficulties you may encounter while working
Create your own cyclone filter, or even homemade vacuum cleaner, as we have seen, it is not difficult, if you have the necessary materials.
In some cases, it is recommended to take metal containers for collecting garbage, as they are considered more durable. In the presence of a vacuum cleaner with huge power, a plastic bucket can “collapse” so to speak. It is drawn in due to the strong flow of intake air. This happens extremely rarely, but it is better to immediately provide for such an option. It can be leveled, but damage to the product will be on the face. So you always need to consider the quality of the plastic and the power of the device. In the case of a traffic cone, this problem does not arise.
From the very beginning of work in the workshop, I faced the problem of removing dust after work. The only opportunity available to clean up the floor was to sweep it. But because of this, just an incredible amount of dust rose into the air, which settled in a tangible layer on furniture, on machines, on tools, in hair and lungs. The concrete floor in the workshop exacerbated the problem. Some solution was to spray water before sweeping and use a respirator. However, these are only half measures. In winter, water freezes in an unheated room and you have to carry it with you, in addition, the water-dust mixture on the floor is difficult to collect and it also does not contribute to the hygiene of the workplace. Firstly, the respirator does not block all 100% of the dust, some of it is still inhaled, and secondly, it does not protect against dust settling on the environment. And not all back streets can be climbed with a broom to pick out small debris and sawdust from there.
In such a situation, the most effective solution it would be to vacuum the room.
However, using a household vacuum cleaner will not work. Firstly, it will have to be cleaned every 10-15 minutes of operation (especially if you work on milling table). Secondly, as the dust container fills up, the suction efficiency decreases. Thirdly, the amount of dust, greatly exceeding the calculated values, will greatly affect the resource of the vacuum cleaner. Something more specialized is needed here.
There are many ready-made solutions for dust removal in the workshop, however, their cost, especially in light of the 2014 Crisis, does not make them too affordable. Found on thematic forums interesting solution- use a cyclone filter in conjunction with a conventional household vacuum cleaner. All of the listed problems of household vacuum cleaners are solved if dirt and dust are removed from the air to a standard vacuum cleaner dust collector. Some collect cyclone filters from traffic cones, others from sewer pipes, others - from plywood and everything that is enough for imagination. But I decided to buy already finished filter with fastener.
The principle of operation is simple - the air flow is twisted in the cone-shaped filter housing and dust is removed from the air under the action of centrifugal force. In this case, the dust falls through the lower hole into the container under the filter, and the purified air exits through the upper hole into the vacuum cleaner.
One of the frequent problems in the operation of cyclones is the so-called "carousel". This is a situation where dirt and sawdust do not fall into the dust container, but swirl endlessly inside the filter. This situation arises from too high a speed of the air flow created by the turbine of the vacuum cleaner. It is necessary to reduce the speed a little and the "carousel" will disappear. In principle, it does not interfere - the next portion of garbage pushes into the container most from the "carousel" and stands in its place. And in the second model of plastic cyclones, this carousel practically does not exist. To eliminate air leakage, I smeared with hot glue the junction of the filter with the cover.
I decided to take a larger dust container so that I had to take out the garbage less often. I bought a barrel of 127 liters, produced, it seems, in Samara - the size is right! I'm going to carry the barrel to the trash can like a grandmother carrying a shopping bag - on another cart, so as not to overstrain.
Next is the choice of layout. Some install the dust collector permanently and lead channels to the machines. Others simply put a vacuum cleaner and a barrel next to each other and drag them to the right place. I wanted to make a mobile unit on wheels to move everything around the workshop in one block.
I have a rather small workshop and the issue of saving space is very relevant. Therefore, I decided to choose a layout in which the barrel, filter and vacuum cleaner are located one above the other, occupying a minimum area. It was decided to cook the body of the installation from metal. frame from profile pipe determines the dimensions of the future installation.
With a vertical layout, there is a possibility of tipping over. To reduce this probability, you need to make the base as heavy as possible. For this, a 50x50x5 corner was chosen as the material for the base, which took almost 3.5 meters.
The tangible weight of the trolley is offset by the presence of swivel wheels. There were thoughts, if the structure is not stable enough, to fill the cavity of the frame with lead shot or sand. But this was not required.
In order to achieve the verticality of the rods, it was necessary to use ingenuity. The recently purchased vise came in handy. Thanks to this simple equipment, it was possible to achieve precise installation corners.
It is convenient to move the trolley by holding on to the vertical bars, so I strengthened their attachment points. In addition, this is an additional, albeit not large, weighting of the base. In general, I like reliable things with a margin of safety.
The barrel will be fixed in the installation frame with the help of clamps.
At the top of the rods is a platform for a vacuum cleaner. Further, holes will be drilled in the corners in the lower part and wooden planks will be fixed with self-tapping screws.
Here is the whole frame. It seems to be nothing complicated, but for some reason it took four evenings to assemble it. On the one hand, I did not seem to be in a hurry, I worked at my own pace, trying to complete each stage with high quality. But on the other hand, low productivity is associated with the lack of heating in the workshop. Goggles and a welded mask fog up quickly, impairing visibility, bulky outerwear hinders movement. But the task is done. Besides, spring is only a couple of weeks away.
I really did not want to leave the frame in this form. I wanted to paint it. But on all the cans of paint that I found in the store it is written that they can be used at a temperature not lower than +5, and on some even not lower than +15. The thermometer in the workshop shows -3. How to be?
Esteemed thematic forums. People write that you can safely paint even in frost, as long as the paint is not on water based and there was no condensation on the part. And if the paint is with a hardener, then do not bathe at all.
I found an old, slightly thickened can of Hammerite in the stash, which I used to paint a horizontal bar at the dacha in the summer -. The paint is quite expensive, so I decided to test it in extreme conditions. Instead of the expensive original thinner, Hammereit added some regular degreaser to make it a little thinner, stirred it to the desired consistency and began to paint.
In summer, this paint dried in one hour. It is difficult to say how long it dried in the winter, but when I returned to the workshop by the evening of the next day, the paint had dried. True, without the promised hammer effect. Probably the degreaser is to blame, not negative temperature. Otherwise, no other problems were found. The cover looks and feels secure. Perhaps it is not for nothing that this paint costs almost 2,500 rubles in the store.
The body of the cyclone is made of good plastic and has fairly thick walls. But fastening the filter to the lid of the barrel is rather flimsy - four self-tapping screws screwed into the plastic. At the same time, significant lateral loads can occur on the hose, which is attached directly to the filter. Therefore, the attachment of the filter to the barrel must be strengthened. People approach this problem in different ways. Basically they collect additional frame stiffness for the filter. The designs are varied, but the idea is something like this:
I approached this a little differently. A holder for pipes of a suitable diameter was welded onto one of the rods.
In this holder, I clamp the hose, which accounts for all the twists and jerks. Thus, the filter housing is protected from any stress. Now the unit can be pulled behind you right by the hose without fear of damaging anything.
I decided to fix the barrel with tie-down straps. When choosing locks in a hardware store, I made an interesting observation. A five-meter tie-down strap with a foreign-made ratchet lock cost me 180 rubles, and a naked frog-type lock lying nearby Russian production would cost me 250 rubles. That's where the triumph of domestic engineering and high technology.
Experience has shown that this method of fastening has an important advantage. The fact is that on the forums dedicated to these filters they write that barrels like mine, when connected to a powerful vacuum cleaner, can be crushed due to the vacuum that occurs when the inlet hose is clogged. Therefore, during the tests, I deliberately blocked the opening of the hose and, under the influence of vacuum, the barrel shrank. But due to the very tight grip of the clamps, the barrel did not shrink completely, but only in one place below the hoop a dent appeared. And when I turned off the vacuum cleaner, the dent straightened itself with a click.
At the top of the unit is a platform for a vacuum cleaner
As a household vacuum cleaner, I bought a bagless almost two-kilowatt monster. I was already thinking, and at home I would need such a thing.
When buying a vacuum cleaner on an ad, I encountered some inexplicable human stupidity and greed. The people sell used things without a guarantee, with a depleted part of the resource, shortcomings in appearance at prices below the store by some 15-20 percent. And okay, these would be some running things, but second-hand vacuum cleaners! Judging by the period of placement of ads, this trade sometimes drags on for years. And as soon as you start haggling and calling an adequate price, you come across rudeness and misunderstanding.
As a result, after a couple of days, I still found for myself great option for 800 rubles. Well-known brand, 1900 watts, built-in cyclone filter (already the second in my system) and another fine filter.
For its fastening, I did not come up with anything more elegant than pressing it with a tie-down strap. In principle, it holds securely.
I had to fiddle a bit with the hose connections. As a result, we have such a setting. And she works!
Usually when you read reviews from the first use of such gizmos, people choke with delight. Here is something similar and I experienced the first time I turned it on. It's no joke - vacuuming in the workshop! Where everyone walks in street shoes, where metal shavings and sawdust fly everywhere!
I have never seen this concrete floor, impossible to sweep due to dust stuck in the pores, so clean before. Persistent attempts to sweep it only lead to an increase in the density of dust in the air. And such purity was given to me in a couple of easy movements! I didn't even have to wear a respirator!
In the barrel, we managed to collect what was left after the previous cleaning with a broom. During operation of the device, due to the translucence of the filter, you can observe dust wisps swirling inside. There was also dust in the dust collector of the vacuum cleaner, but it was a small amount and these were especially light and volatile fractions.
Very pleased with the result. No more dust storms in the workshop. You could say I'm entering a new era.
Advantages of my design:
1. Occupies a minimum area, due only to the diameter of the barrel.
2. The unit can be dragged and pulled by the hose without being afraid to pull out the filter.
3. The barrel is protected from crushing when the inlet pipe is clogged.
After some time of using the installation, I still ran into the problem of a lack of barrel rigidity.
Bought a more powerful vacuum cleaner. Household, but sucks like a beast - sucks stones, nuts, screws, tears off plaster and pulls bricks out of masonry))
This vacuum cleaner slammed the blue barrel even without clogging the inlet hose! Tight girth of the barrel with clamps did not help. I didn't have my camera with me, sorry. But it looks like this:
Thematic forums warn of such a possibility, but still I did not expect this. With great difficulty he straightened the barrel and sent it, fairly dented, to the dacha to store water. She is not capable of more.
There were two ways out of this situation:
1. Buy instead plastic barrel metal. But I need to find a barrel of a very specific size so that it fits exactly into my installation - diameter 480, height 800. A superficial search on the Internet did not give a result.
2. Assemble the box yourself right size from 15 mm plywood. Here it is more real.
The box was assembled on self-tapping screws. The joints were sealed with double-sided foam tape.
The trolley had to be redone a bit - the rear collar was digested for a square tank.
The new tank, in addition to strength and volume increased due to right angles, has another important advantage - a wide neck. This allows you to install a trash bag in the tank. It greatly simplifies unloading and makes it much cleaner (I tied the bag right in the tank and took it out and threw it away without dust). old barrel didn't allow it.
The lid was sealed with foam insulation for windows
The lid is held by four frog locks. They create the necessary tightness to seal the cover on the foam pad. A little higher, I wrote about the pricing policy for these frog locks. But I had to fork out.
Well done. Nice, functional, safe. How I love.
A home vacuum cleaner is so familiar to the household that no one thinks about the principle of its operation. Since the invention of this cleaning assistant, it has been used exclusively possible way separation of dust from clean air- filter.
Over the years, the filter element has been improved, from a banal bag of thick tarpaulin, it has turned into high-tech membranes that hold the smallest particles of debris. At the same time, it was not possible to get rid of the main drawback.
Filter makers are constantly looking for a compromise between cell density and air throughput. In addition, the dirtier the membrane, the worse the air flow through it.
30 years ago, physicist James Dyson made a breakthrough in dust collection technology.
He invented a compact dust separator that works on the principle of centrifugal force. Needless to say, this idea was not new. Industrial sawmills have been using centrifugal scorch and chip accumulators of the "cyclone" type for a long time.
But no one guessed to apply this physical phenomenon in everyday life. In 1986, he registered a patent for the first cyclone type vacuum cleaner, called G-Force.
In general, there are three ways to separate dust from clean air:
- filter membrane. The most massive and cheap way remove dust. Used in most modern vacuum cleaners;
- Water filter. Air with garbage passes through a container of water (like in a hookah), all particles remain in a liquid medium, and a perfectly clean air stream enters the outlet. Such devices have gained popularity, but their use has not become widespread due to the high cost.
- Centrifugal dry cleaning filter of the "cyclone" type. It is a compromise in terms of cost and quality of cleaning in comparison with a membrane and a water filter. Let's take a closer look at this model.
The principle of operation of the cyclone
The illustration shows the processes taking place in the cyclone filter chamber.
Polluted air through the pipe (1) enters the filter housing (2) cylindrical shape. The branch pipe is located tangentially to the walls of the housing, due to which the air flow (3) is twisted into a spiral along the walls of the cylinder.
Under the action of centrifugal force, dust particles (4) are pressed against the inner walls of the housing, and under the influence of gravity, they settle into the dust collector (5). Air with the smallest debris particles (which are not affected by centrifugal force) enters the chamber (6) with a conventional membrane filter. After the final cleaning, they exit to the intake fan (7).
The membrane filter is minimally contaminated and only needs to be cleaned occasionally after cleaning. All the dirt is simply poured out of the drive, and the vacuum cleaner is ready to work again.
Vacuum cleaners with such a filter are cheaper than water ones, but still more expensive than membrane ones. Therefore, many craftsmen make a cyclone-type filter with their own hands, and connect it to the entrance to a conventional vacuum cleaner.
About filters.
The cyclone filter does not retain more than 97% of dust. Therefore, additional filters are often added to them. From English, "HEPA" translates as High Efficiency Particulate Air "- a filter for airborne particles. 
Agree that even you cannot imagine your life without such necessary equipment like a vacuum cleaner? They cope not only with dust, but also with dirt.
Of course, vacuum cleaners can be used not only at home, but they are also different: rechargeable, washing, pneumatic. As well as automotive, low-voltage industrial, knapsack, gasoline, etc.
The principle of operation of a cyclone vacuum cleaner
James Dyson was the first inventor of the cyclone vacuum cleaner. His first creation was G-Force in 1986.
A little later in the 1990s, he applied for the manufacture of cyclone apparatus and already assembled his center for the creation of vacuum cleaners. In 1993, his first vacuum cleaner, known as the "Dayson DC01", went on sale.
So after all, how does this miracle of a cyclone type work?
It looks like the creator, James Dyson, was a remarkable physicist. Thanks to centrifugal force, it is involved in dust collection.
The device is two-chamber and it is divided into two types - external and internal. The air that swirls inside the dust collector moves upward as if in a spiral. 
By law, large dust particles enter the outer chamber, and everything else remains in the inner chamber. And the purified air leaves the dust collector through filters. This is how vacuum cleaners with a cyclone filter work.
Vacuum cleaners with a cyclone filter, features
Do not opt for those models that require little power. You will definitely not like such cleaning and most likely want to throw away such a device.
Do not waste money in vain, but approach the purchase of a vacuum cleaner more seriously. One has only to contact the sales consultant and he will help you with the choice of one or another vacuum cleaner.
The device should be chosen, which is 20-30% more powerful than a bag vacuum cleaner. It is best to take the one with a power of 1800 watts. Almost all manufacturers of vacuum cleaners produce models with this filter, which is good news.
Advantages of cyclone dust collectors
1.Skazhdym, probably, it happened when you accidentally found the item you needed in the dust collector? Now this is not a problem because it is transparent! And you will always be able to notice the items that you need to get out of there as soon as possible.
This is one of the most important pluses.
2. The power of such vacuum cleaners is maximum and does not slow down the speed and power, even with a clogged container. Cleaning is much more pleasant, power does not drop, cleaning is cleaner.
Such a vacuum cleaner is capable of detaining much more than you imagine. Up to 97%!!! Not likely, right? Although some are dissatisfied with this result, as they prefer vacuum cleaners with a water filter.
3. Buying a cyclone vacuum cleaner not only makes a bargain, but also saves storage space, as its weight is quite light. You don't have to carry heavy things. 
4. No need to constantly change paper bags for vacuum cleaner.
5. Power. She is not lost from fullness.
6. It can be washed well with water and dried.
Cons of cyclone dust collectors
1. One of the disadvantages of these vacuum cleaners is not very pleasant. This is washing and cleaning the filter. Of course, you don’t have to clean the container every day with a brush, but still, this is one of the minuses. Laziness is present in every person. Yes, it is certainly unpleasant to face the fact that you need to get your hands dirty.
2. Noise. The noise from this type of vacuum cleaner is much greater than from a conventional one.
3. Power consumption. It is also much higher than from a conventional vacuum cleaner. This is a small tornado.
Buy this little miracle or not, it's up to you. In fact, all its advantages cover those not many of its shortcomings. Cleanliness in the house is much more pleasant than not fully completed tidy, agree?
Personal impressions
Compared to the old vacuum cleaner, the cyclone dust collector looks quite modest in size. It is impossible to believe that such a little one is capable of something serious. Now old vacuum cleaner can only be used for wet cleaning.
I take out accessories, at the first use, I insert a pipe that is not large in diameter, I turn on the device, and what really surprises me is that the brush cleans carpets much better than my previous assistant.
He cleans everything. Dirt, the hair of our pets. Previously, it was necessary to make no small effort to cope with such “little things now”.
I have laminate flooring in the hallway and it was just as easy to clean. The fact is that I have another brush in stock, harder than the previous one for carpets, so I just coped with this task. You know, and the sound of this vacuum cleaner is not as loud as they wrote about it on the Internet. 
I am pleased with this device because it is light and not so loud. I also liked the compartment for storing all the necessary nozzles, it is very convenient that it is built into the vacuum cleaner itself.
Once I knew what this little tornado was capable of, it was time to clean the container. Thank God, when I began to shake out the garbage from the dust collector, it fell in dense large lumps.
Since the debris was tamped down by the air flow. There are no balls of dust to be seen, and it did not rise into the air! So I finished my first cleaning with my cyclone vacuum cleaner. I washed the container and that was the end of the cleaning!
Cyclone for vacuum cleaner photo
All vacuum cleaners are designed for one purpose - cleanliness. This applies to all vacuum cleaners.
Industrial and construction vacuum cleaners usually used on machines or for cleaning any premises. These vacuum cleaners are expensive, since the principle of operation of the cyclone filter vacuum cleaner must be selected carefully.
You should also know that most often industrial devices are used during repair and construction. Leave your workplace need to be clean.
DIY cyclone, made of transparent plastic video
Construction work is carried out after its preparation and surface cleaning. As you understand General cleaning impossible to do with a conventional vacuum cleaner. In other words, it is fraught with damage to the device.
Even small debris, such as: sand, oil, dry mixes, powdered abrasives and wood shavings, is designed only for an industrial vacuum cleaner.
If you suddenly go to choose a vacuum cleaner for construction works, then be sure to specify the types of pollution that it will encounter.
Have you thought about using a vacuum cleaner in repair conditions? Then consider the option of a do-it-yourself cyclone for a vacuum cleaner. There are many examples of how to make this kind of vacuum cleaner.
Do-it-yourself cyclone for a vacuum cleaner
1. In order to make such a vacuum cleaner on your own, you will need a Ural PN-600 vacuum cleaner, a plastic bucket (even out of paint), a pipe 20 cm long and 4 cm in diameter.
2. The nameplate is also unscrewed, and the holes must be sealed.
3. The pipe is quite thick and will not fit into the hole, so you need to grind off the rivets with a grinder and remove the pipe fasteners. Before that, remove the springs with clamps. Wrap electrical tape around the plug and insert onto the plug.
4. At the bottom, make a hole with a drill in the middle. Then expand it to 43 mm with a special tool.
5. Gaskets with a diameter of 4 mm are cut out to seal it.
6. Then you need to fold everything, the bucket lid, gasket, centering pipe.
7. Now we need self-tapping screws 10 mm long and 4.2 mm in diameter. Self-tapping screws will need 20 pieces.
8. From the side of the bucket, cut a hole along the suction pipe. The cutout angle should be 10-15 degrees.
9. We try on and edit the shape of the hole using special scissors that cut through metal.
10. Do not forget that you also need to try on inside. Also leave strips for self-tapping screws from the inside.
11. With a marker, mark the hole in the bucket and cut off the excess material with scissors. Fasten the pipe from the outside to the bucket.
12. To seal everything, use a 30x bandage. From an ordinary first aid kit and glue like "titanium" for foam. Wrap the bandage around the nozzle and saturate with glue. Preferably more than once!
13. While the glue dries, you can check how this vacuum cleaner will work. Turn on the vacuum cleaner and load it by blocking the nozzle with your palm. When checking the operation of the vacuum cleaner, the sealing process and connection with the nozzle are improved. It is unlikely that he will soon become obsolete.
14. Vacuum cleaner is best stored in a case.
