What to do if there is a hole in the air mattress. How to glue - fix an air mattress with your own hands

No special skills required to glue inflatable mattress and extend its service life. It is worth mentioning that not all products make sense to repair. You can figure out whether the goods are not subject to disposal if damaged, even at the time of purchase. Air mattresses that are worth trying to seal are completed with a patch and rubber glue. If there is no repair kit, most likely, the product is easier to throw out.

Features of the repair of mattresses for bathing

Mattresses for resting on the shore and water get damaged more often than sleeping ones, stumbling upon a sharp stone, a random fragment - any sharp object. At the same time, a repair kit is rarely attached to them - this means that the mattress cannot be repaired. You should pay attention to its design.

Products from two or more independent sections can be glued. A puncture in a separate part causes inconvenience, but practically does not affect safety when swimming. It can and should be repaired. It is better to refuse swimming on a sealed single-section mattress.

These recommendations apply to single damage. If a multi-section mattress is damaged a second time, and already in another section, operation on the water is not recommended. The same - if there are punctures on the same section, but from different sides (bottom and top), since the mattress suffers strong loads in water - air pressure from the inside, water from below and from the sides and the body from above.

Repair will require:

a flap of material similar in quality to a mattress;
waterproof glue;
degreaser, thinner, acetone, alcohol or high octane gasoline;
heavy object with flat surface- press.

Important! The place of gluing will always be a risk zone. Do not swim far on a repaired mattress and do not load it beyond the norm indicated by the manufacturer in the instructions.

How to determine the puncture site: two ways

The repair of air mattresses (of any type) begins with determining the location of the damage. Cuts or a tear along the seam are not difficult to find, it is more difficult to see a pinhole. Cyclists and owners inflatable boats this problem is well known.

The water method:

The balloon filled with air is lowered into water and heated.
Air begins to escape from the damaged area, bubbles rising in a stream - this is an indicator of the puncture site.
In order not to lose the detected defect, it is first pinched with a finger, and then circled with chalk, soap or a contrasting alcohol marker.

The disadvantage of this method is that it is necessary to wet the product, and then dry it thoroughly for further gluing. This is especially inconvenient when repairing velor mattresses - the silky surface dries for a long time.

Testing without water

If there is no container to lower the mattress into it or there is no time to wait until it dries, then the puncture is found by sound. The product is arbitrarily compressed and listened to. Coming out of a small hole, the air hisses.

You have to be careful not to make a mistake. It is more convenient if the mattress is loosely inflated - then the dense part is moved around the perimeter in order to more accurately determine where the quiet hiss comes from. The method is best suited for sprayed products, but is the least accurate.

Another method is with soap. The product will have to be moistened, but not as much as when lowered into water. The bottom line is to inflate the mattress and lather the approximate puncture site. There is no need to press: if there is damage, the air itself will come out of it, inflating the bubble. According to it, the future plot for a patch is noticed.

Advice! If there is absolutely nothing to circle the puncture, insert a match or a toothpick with a cut point into it.

Several ways to repair air mattresses

To firmly glue an air mattress, be sure to follow five steps:

Cleanup.
Degreasing.
Drying.
Primary processing adhesive composition.
Bonding with placement under the load during the day.

Important! The patch material should be identical to the mattress or as close as possible in quality and composition.

The patch is ideally placed double - on the inside and outside, especially when it comes to a cut or a strong gap. For a small puncture, an external seal is sufficient. In any case, it is necessary to ensure that the glue does not leak into the mattress - otherwise it will stick together and become at best uncomfortable, and at worst - unusable. Therefore, the glue is applied in a thin uniform layer, not reaching the edge of the patch 1-2 mm.

Stripping is the complete removal of everything that will interfere with the adhesion of the adhesive and the base. Smooth products are thoroughly washed, but velor types Intex, will have to be freed from the pile. To do this, take sandpaper with fine grain, with caution you can use a knife, razor, etc.

Urgent repair of minor damage with improvised means

Mounting tape is used as an "ambulance" for a damaged watercraft. Its advantage over other products of a similar purpose lies in the strength of the fit and elasticity. The method is also convenient in that it is applicable both at home and in field conditions, and there is no need to wait until the first layer of glue dries. The disadvantage of the method is lower strength and durability and the inability to repair a strong gap. Tape is good against pinholes and small cuts.

Interesting fact
Gray adhesive tape with a stretching effect is used by plumbers to temporarily fix a leak. And the insulation of such material lasts for years.

Mode of application:

Clean and degrease the damaged area.
Let dry.
Seal with tape. A long cut is desirable - in two layers: the first - along, the second - across.

About the same specifications has white electrical tape for electrical wires. It is inferior to the "rubber" adhesive tape in width and stickiness. For temporary repair of a pinhole in a sleeping mattress, it is suitable - but it must be fastened with two pieces crosswise.

Repair of major damage

A mattress torn at the seam cannot be repaired with adhesive tapes: the pressure on the side elements is too high. In this case, you need to put a patch.

Advice! The encircling rigid frame reduces the deformation of the mattress, so it is more comfortable to sleep on it. And the same element is a guarantee that after a serious repair the product will still serve.

Possible difficulties:

Inconvenient for home repairs is a model in which the side elements are not an addition, but part of an inflatable balloon.
Reliable and tight coupling provides uniform load pressure. To do this, it must be flat at the bottom, heavy and capture every millimeter of the patch. In case of significant damage, it is difficult to select the required dimensions of the cargo, but it is necessary. If such a pressing tool is not found, but improvised materials of different weights and shapes are used, then some areas will let air through after the first use of the mattress.

To repair a mattress along the seam, you will need:

two smooth thin slats;
clamps;
rubber-based adhesive;
acetone;
rectangular patch.

Procedure:

The area around the damage is treated with acetone.
After it has evaporated, glue is applied in a thin even layer.
The same preparatory work carried out with two patches.
Lubricated parts are kept in air (the time of this stage is individual for each type of glue, it is indicated on the tube).
Carefully insert the inner patch and align its middle with the center of damage.
The second patch is applied on top, carefully smoothed. After connecting the parts, there should be no air bubbles between them.
From below and above the seam to be glued, over the patch, rails are applied and fixed with clamps.
Leave the mattress in a vice for a day or half a day.

A more reliable method of repair is only vulcanization used for repair car tires. For this service, it is better to contact the nearest tire shop.

Air mattresses are convenient for relaxing on the water or as guest beds. If the product is damaged and began to let air through, it is worth trying to seal it. No special skills are needed for the procedure, only accuracy and time. A repaired one-section mattress will serve only on the shore, if there are several sections, it is quite acceptable to swim on it.

Repair of air beds and mattresses at home: methods and useful recommendations.

Air mattresses or beds are easy to transport, easy to care for, have a small volume during storage when assembled and a relatively inexpensive price. Thanks to these qualities, they are an indispensable thing when friends are visiting you or when traveling on vacation, when living in tent conditions. Their only disadvantage is that even the slightest damage immediately excludes the further operation of the mattress. How to repair an inflatable product yourself? How to do it right - let's talk in this article.

How to find a hole in an air mattress: ways

Looking for a hole

Searching for a hole is a very difficult task. As a rule, they are scanty in size and it is problematic to notice them with the naked eye.
Some effort and a little patience will help you find the damage as quickly as possible using the following search methods:

Examine the seams. Most often, it is at the joints that mattresses are torn, due to their excessive inflation.
Next, move on to surface inspection.
If after visual inspection it was not possible to find damage, use the following methods:

1 option

Inflate the mattress to the maximum possible
Listen to the outgoing sound
Help with a wet hand to identify the source of damage. We bring it to the source of the sound signal - the air should cool the palm
We mark the found hole with a marker

Option 2

You can use it in nature, in the presence of a reservoir
Immerse the product completely in water
Close inspection reveals air bubbles
Fix the damage with chalk

3 option

Apply soap suds with a spray bottle to the intended object of damage, with the mattress inflated
Bubble foam will accurately indicate the problem area

4 option

Mix five liters of water with liquid detergent for dishes
Pour liquid into a deflated mattress
Inflate the product and shake it slightly
Soap foam will actively whistle out through the existing holes.
Mark leaks with permanent marker

Precautionary measures:

Do not place the mattress on sharp objects during the examination.
Do not over-inflate the product. This may cause an explosion.
Despite the presence effective way testing by pumping water inside, it has its negative consequences. In the future, the mattress is problematic to dry - mold may appear.
Check the manufacturer's recommendation first. Maybe your bed shouldn't get too wet. When in contact with water, the seams may lose strength, and this may also lead to peeling protective coating on synthetic fabrics.

After detecting damage, you can proceed to the restoration of the product.

Glue for repairing air mattresses and beds: brand, names

The best remedy for gluing air beds

The following brands of glue are suitable for gluing mattresses:

THF (tetrahydrofuran)
Moment-Crystal
Quelyd "MaxiGlue"
The moment is universal
Desmokol
Nano Kleber

How and how to seal a hole on an air mattress: recipe, instructions

Reconstruction process

Usually a repair kit is sold along with the mattress.

In its absence, we stock up:

polyurethane adhesive
A specially purchased patch or piece of rubberized material

Main stages:

Cleaning up the damaged area sandpaper
Degrease with alcohol solution
Apply adhesive to the patch
Pressing to the surface
Leave under pressure for 12-24 hours
Then remove the press
Doing a blow test

How and how to seal an air mattress at the seam: recipe, instructions

More complex damage

The seam on the mattress is sealed from the inside
To do this, pull the damage site through the valve and proceed with the repair, in the same way as indicated above.
Once completely dry, turn the mattress back to its original position.

How and with what to seal an air mattress from the velor side, from the flock side?

We glue the fleecy coating

Choose a flat hard surface
We straighten the mattress
We treat the damaged area and a few centimeters around it with lacquer liquid
After a few minutes, remove the pile with a blunt knife.
We process for degreasing again with a solvent. It is better not to use sandpaper. This can lead to small cuts that lead to larger injuries.
Next, cut out a patch a few centimeters larger than the hole. Suitable for this purpose: thin rubber, oilcloth, electrical tape
Wipe for degreasing solvent
Lubricate the patch and surface with glue
Dry 5 minutes
We process with glue a second time
We expel the accumulated air between the surface and the patch, leveling with a cloth
We put oppression at 12-30 hours
Next, we use the mattress, trying to prevent additional damage.

How to glue an Intex air mattress: instructions

One way to do quality work

Blowing air out of the mattress
Fixing the damaged area
Cleaning the bonding area
Degrease with toluene
We apply any transparent material, draw the outline of the patch
Cut out a pattern, 4 cm larger than the damage
Apply a small amount of glue to both surfaces
Dry without laying on the mattress
We smear a second time, dry for 5 minutes
Using a hair dryer, heat the glue to activate it.
Pressing the patch to the cut
To avoid air residue, iron with a roller. We press down with a load
Dry for at least a day

Additional Tips:

Repair the smooth part with clear vinyl.
When a defect is formed on the flock surface:

First, clean the pile with sandpaper or rinse with alcohol - otherwise the patch will not stick
Next, carry out the same manipulations as on the smooth side, but with a flock patch

Video: How to glue an air mattress on a velor surface?

Can an air mattress be sealed with superglue?

Is this product suitable?

Such glue is universal, as it glues almost all materials.
But not all varieties of superglue are suitable for gluing an air mattress.
There are varieties that have a cyacrine base. They solidify very hard, which is not acceptable for a rubber product.
From this series of superglue, glue with a rubber base is suitable. It stays flexible after drying.

Is it possible to glue an air mattress in a tire shop?

In emergency cases, when there is no repair kit at hand, you can use the services of tire fitting
But then it’s better to re-paste the patch, since the mattresses glued in auto workshops look very rough and not aesthetically pleasing

Air Mattress Instruction Manual and Damage Warning

Careful operation: a guarantee of a long service life

After repairing the product, try to avoid further damage to it later.

To do this, follow a few simple tips:

Inspect the place where you plan to place the inflated mattress. If there are sharp objects, remove them.
Avoid playing with cats and dogs. Their sharp claws can break the integrity
Move the mattress over the surface carefully. Pulling too hard can cause the seams to come apart.

One of the above methods will definitely help to identify a hole, make a quality restoration of a bed or mattress. A correct use and precautions will help long time use a practical and comfortable product.

Video: How to seal a mattress (as easy as shelling pears) "be sure to read the description for the video"

An air mattress is not only good decision for water activities, but also an alternative to a bed. At home, it can be used to accommodate guests. Such products are compact, when folded they practically do not take up free space.

They are durable, especially when handled with care. But, even in the event of a puncture, can be glued air mattress by yourself. Required for repair inexpensive materials, available in hardware and hardware stores, a minimum set of tools and improvised means.

Should You Repair Your Mattress?

The mattress can be damaged both during rest - by branches, stones or even sand, and at home, for example, thanks to pets. But, you don't need to get rid of it. Do-it-yourself restoration is needed patches and glue. Following the instructions, you can glue an air mattress at home no worse than professional craftsmen.

It is easy to seal a rubber product, it is much more difficult to find a hole in an air mattress. As a rule, it is very small, it is difficult to find it by visual inspection and by sound. First of all, you need to check the valve. It could wear out and start leaking air.

In 90% of cases, holes in mattresses are formed at the seams. The next most common are damage to the lower surface. It is often damaged by debris present in nature or in a pond, but it can also be pierced at home.

First of all, you should decide with the site of injury. First you need to visually inspect the entire product. If it was not possible to identify a puncture, several more effective methods are used.

Search for a damaged place

Often it is not possible to visually find a hole in the rubber due to its elasticity. But, with severe damage, such places are noticeable. If it is visible visually, put the back of your hand on it to check. If there is a hole, you will feel a cool air flow.

Better dip your hand in water. This makes it easier to detect air flow, as air bubbles should appear when you apply the brush. You should not rush, examine the surface in detail, perhaps several holes have formed.

Immersion in water

If the defect is found directly on the pond, the mattress should be inflated and immersed in water. To create additional pressure, you can sit on the product. Bubbles should come out of the hole. The place of their exit is the damage.

With soapy water

Bubbles will be more visible if you use soapy water. You can simply treat the entire mattress with soap using a sponge or cloth. Fits both regular and liquid soap. It is more convenient to work with the latter, since it already has a liquid consistency.

Add some soap to the water and go over the entire piece with a washcloth. Special attention give seams. Bubbles will start to stand out even from small holes.

By sound

A puncture can be found by a characteristic sound. But, it is advisable to do this in a quiet place, without distracting noises. Inflate the product and lean against it in different places. A characteristic hiss will be present at the puncture site.

Liquid filling

Due to the inconvenience, this method is rarely used, but in difficult cases it can be more effective. The mattress must be filled with water. If there is a gap, liquid will flow through it. You can fill the product with a watering can.

The disadvantage of this method lies in the complexity of the subsequent drying of the internal cavity. The design is almost completely sealed, so even with the valve open, the product will dry for a long time. Therefore, it is recommended to resort to this option only in summer in warm weather in order to speed up drying.

May remain on the mattress white stains. If this is not critical, follow these steps:

release the air;
prepare water with a little soap (you can use plain water, but with soap the efficiency is higher);
pour approximately 3 liters of liquid into the mattress. When working with dimensional models, more volume may be required;
inflate the mattress tightly;
Turn the product over several times so that the solution is distributed along the inner walls. The gap will be noticeable by hissing and water flowing out;
use a marker, chalk, or soap to mark the puncture.

Surface preparation for gluing

Rubber at the site of damage must be cleaned of contamination. The surface must be completely dry. Do not dry the mattress hair dryer or heaters, it may damage the material.

If a hole is formed on the fleecy side, the area must be lightly sanded with fine-grained sandpaper. This is necessary to ensure the tightness of the patch and improve the adhesion of the adhesive.

Degrease the cleaned area. You can use alcohol, acetone (nail polish remover will do) or similar non-aggressive solvents. You can use a small amount of gasoline.

Tools and materials

There are several ways to seal an air mattress. The best option- use a special repair kit. The Intex company produces such restoration kits its products. Set includes:

transparent vinyl film;
flock patch;
glue.

The set comes with instructions. Repair kits are sold in stores specializing in the sale of mattresses and auto parts. It is advisable to buy 1-2 sets when purchasing the product. The set is compact, if necessary, you can take it with you on vacation.

In the absence of the possibility of buying a ready-made set, you should resort to improvised materials:

a patch can be made from any piece of rubber - old wheel tubes, children's toys, circles, etc .;
for gluing, you can use any glue for rubber products. But, do not use superglue, it will damage the material.

To perform the work, you need scissors, sandpaper with fine grain, a brush for applying the adhesive composition and a marker for making marks.

Adhesive selection

There are a lot of adhesives on the market that are designed to work with rubber. But, can not use products with the effect of instant gluing. They usually contain a substance that corrodes rubber.

The moment is universal

One of the most popular adhesives. Suitable for both rubber and other materials, including plastic, ceramics, wood and others. The joint reaches maximum strength after 24 hours.

Polyurethane Shoe Adhesive

Adhesive solution based on polyurethane. Also found on sale under the name "Desmokol". Effective remedy recovery leather goods, but also glues rubber parts well.

PVC adhesive

An effective solution for PVC products. Also suitable for air mattresses. The advantage is that there is no need to use a separate patch. It is formed by the adhesive composition itself during polymerization, due to which it received the name "Liquid Patch".

Not affected by moisture. Available in various colors, which allows you to repair any product without compromising aesthetic qualities.

Super Moment

Composition based on natural rubber. But, for the restoration of rubber mattresses, it is better not to use. After hardening, it acquires a very hard structure, in further operation it can crumble, including damaging the mattress material.

rubber adhesive

Applied on both bonded surfaces. After application, you need to wait 2-5 minutes, attach the parts and squeeze tightly. It is advisable to leave the connection under pressure for a while. Full hardening occurs after a day.

Making a patch

The size of the patch should completely cover the hole, capturing a little of the surrounding whole material. But, it is not worth making it excessively large, this will create an additional load on the rubber. Before gluing the patch and the damaged area, be sure to degrease.

If there are several adjacent gaps, they can be sealed with one large patch. But, it should completely cover the damaged area and have a small margin.

Surface sealing

The thickness of the adhesive layer depends on its type, so you need to follow the instructions from the manufacturer. So, "Moment" is applied in a thicker layer, and "Desmokol" is as thin as possible. After application, wait a while for the adhesive to dry slightly.

Apply the patch to the injury and press firmly for 2 minutes. Try to press the entire part at once, eliminating its displacement. The mattress can be used after the glue has hardened, the specific time is always indicated in the instructions.

Seam sealing

Seams can usually be sealed with glue. It is important to wait for it to completely harden. The layer is thick, so you have to wait a while, preferably at least a day. There is also a more complicated but effective solution:

the damaged part of the product must be turned out through the valve hole;
degrease the damaged seam;
wait for the product to dry;
cut a patch from a rubberized fabric and glue it;
press the part firmly against the defective seam.

Using this method, do not rush to operate the product. Leave it on for at least 12 hours. After the glue has cured, turn the product inside out and inflate to check.

If the restoration fails, try repairing the gap again. Do not dismantle the patch, but stick an additional patch on top of it. bigger size. Especially carefully lubricate the edges of the patch with glue. Peeling of the part usually starts from the edges.

To prevent the patch from peeling off after repair, clean it with sandpaper and completely cover it with glue.

How to avoid new damage?

Not recommended transport the mattress in an inflated state. If there is no desire to blow it off every time, at least you need to carefully carry it in your hands, trying not to catch third-party objects. Allocate a separate place for him at home, better inaccessible to children and animals. Keep the product dry only. If the mattress is used as a guest bed at home, keep it in its original packaging and deflate it when not needed.

An air mattress is a fairly durable thing, and by itself it is unlikely to begin to let air through. The most common cause, due to which the product fails, are sharp cat claws. But is it worth saying goodbye to your beloved cat because of this? Moreover, a damaged thing can be easily repaired if you know how and with what to seal an air mattress.

How to find a puncture

Is it possible to glue the air mattress yourself? Undoubtedly.

For this you will need:

pump;
marker;
container with water (for the first method);
sponge and any foaming agent (for the second);
flour or starch (for the third method);
matches or a lighter (for the fourth).

1st method: dipping

A reliable way to find a damaged area before you seal an air mattress at home is to submerge it in water. If the mattress is very small, a bowl of 10-20 liters is enough, a larger item will have to be put in the bath, but an “adult” full-fledged mattress will fit only in a country pool or a small pond.

The product in which you want to find a hole is pumped up with a pump and placed in a container of water. Then carefully observe: air bubbles will be visible at the puncture site.

To detect a defect, it makes no sense to throw a thing into a river or other body of water with a constant flow, because small air bubbles in such water can hardly be seen.

Having found a hole, it is immediately marked with a felt-tip pen. But do not rush and immediately remove the product from the water. Perhaps there is more than one puncture and there are tiny holes nearby, due to which the mattress, repaired in the most careful way, will still poison the air.

2nd method: soaping

If the product is large, and there is no pond or pool nearby, you can find a puncture, due to which the air mattress descends, using foam.

To do this, take any means for washing or washing and whip into foam. With a foam sponge, apply the resulting foam to the entire surface and fix where air bubbles appear. On thick foam, they will be easy to spot.

What if there are no bubbles? Then the puncture is on the other side, and you will have to repeat the soaping procedure from the beginning.

3rd method: powdering

In addition to those described above wet ways exists and dry. It is used before sticking the air mattress on the velor side.

Soap solution on such a surface foams very poorly, besides, damp furniture, albeit inflatable, is not the best. nice thing in the house. Therefore, a completely dry mattress is powdered with starch, flour, ground mustard or other powdered agent. At the puncture site, the light powder will be blown away by the air coming out of the hole.

After all the punctures are found, the spilled flour from the surface is collected with a vacuum cleaner.

4th Method: Trial by Fire

How to find a puncture in an air mattress in this way? Very simple. All you need is matches or a lighter. You need to carefully monitor the flame: at the puncture site, it will be slightly blown out by air coming out of the hole.

5th Method: Pets

There is another proven way to find a puncture. If you have a cat or a cat in your house, then after you pump up the mattress, they will definitely find a hole from which air is blowing. And this will happen for several reasons:

Good hearing. The faint sound coming from the mattress opening is clearly audible to them.
Curiosity. Due to him, the pets begin to search.
Playfulness. After the discovery, they begin to play with a thin "stream" of air.

This method is not fiction and has happened more than once.

How to seal

After making sure that all damage is found, you can start repairing the air mattress with your own hands. To do this, a patch or a special sticker is applied to the puncture.

Side 1

Before sealing a hole in an air mattress on the smooth side, prepare:

glue;
patches;
fine sandpaper (skin);
scissors;
degreasing liquid (solvent).

The place marked with a marker is cleaned with sandpaper and degreased with a solvent.

Cut out the patch right size, better without sharp corners, - oval or round shape. The patch should be at least 3 centimeters larger than the cut on each side.

To repair the smooth side, use a transparent vinyl film.

After gluing, the product is not used for another day or two, until the seam acquires the necessary strength. It is advisable to press down the gluing place with something heavy.

Never use super glue to repair a PVC air mattress. The alpha-cyanoacrylic acid contained in it will irrevocably ruin the vinyl, and the item will simply have to be thrown away.

Side 2 (velor)

If the defect has formed on the flocked side, the soft pile (“velor”) is carefully cleaned with sandpaper or washed off with alcohol, otherwise the patch will not stick. Then proceed in the same way as when repairing the smooth side. Only a special patch is used - from flock.

Unfortunately, sticking such a patch imperceptibly will not work. In order not to make bald patches on velor, you can try to glue the product from the inside. To do this, helping yourself with a ruler, pull the defective area to the wide opening used for inflation. Glue the patch and wait 12 hours. After that, the product can be turned back.

The advantage of this method is that the product can be repaired almost imperceptibly. And, besides, the patch holds especially tightly because the air presses on it from the inside.

And finally, the most difficult question: how to seal an air mattress along the seam. This is the worst possible damage. It is unlikely that in this case it will be possible to qualitatively repair the thing at home. It is better to find out where the air mattress repair shop is located and contact the professionals. After all, they have not only experience, but also special equipment.

If they nevertheless carry out repairs on their own, the mattress is turned out, the damaged area is degreased with alcohol and the patch is fixed.

Advantages of INTEX glue

People often ask what glue to glue a PVC air mattress with? By and large, any one designed for gluing rubber or PVC products will do. You can use desmocoll (desmokol) - an adhesive for repairing air mattresses, containing natural rubber at its core.

The reliability of the connection will increase significantly if you act on a certain technology. To do this, a desmokol is applied to the parts to be glued, they wait until the glue dries, after which the dried layer is heated with a hot hairdryer and both parts are pressed strongly.

But it is logical to assume that best glue for intex mattresses, the one that is produced under the same name, that is, INTEX branded glue. The repair kit includes patches of several types and the glue itself.

Those who have already tried intex glue in practice claim that it reliably glues not only mattresses, but even inflated pools. The patches last for several seasons.

An air mattress can be successfully used both as a bed and as a watercraft. And in order for it to serve for a long time, only two conditions must be met - dry well before storage and protect from sharp objects.

You shouldn't push it too hard. In order not to "overdo it", it is better not to use powerful automobile pumps and compressors for this.

Release air gradually. If you press hard on the surface to speed up the process, you can damage the seams.

Clean such products with a solution of neutral soap or shampoo. The less chemicals, the better. Abrasive powders are also better not to use.

In the event of a cut or tear, of course, you can glue the mattress yourself, but if the damage is large (more than a centimeter), it is better to contact a specialized workshop to repair it. The help of professionals will also be needed if the mattress has been damaged by dog teeth or claws.

The master will not only repair the gaps, but also completely replace the damaged parts, if necessary.

The popularity of inflatable furniture is due to its ease of use and compact size when folded. It can be used both on tourist trips and at home, as an additional bed. Active operation of the product often leads to the appearance of holes through which air escapes, so the owners often wonder how to glue the air mattress on their own.

We glue the mattress with glue (click to enlarge)

Violation of the integrity of a PVC product is not a reason to throw it away. Typically, branded inflatable furniture sales centers provide repair services for their products. Experts know how to properly restore the product. However, when choosing where to stick an air mattress, it must be borne in mind that this is an expensive service.

Why is air coming out

Intex products may deflate different reasons. It is not always the fault of a puncture or rupture. The valve may be the source of the problem. Perhaps the debris that has accumulated in the grooves does not allow the cover to be screwed tightly enough, in which case it is enough to rinse the part. A broken plug can be replaced.

Sharp objects or pet claws may cut the fabric of the product. From improper use, the seams diverge and tear internal partitions air mattress.

Methods for detecting a defect

To repair the product, you need to find the place of damage. Often the holes are small and almost impossible to notice. There are several methods by which a gap can be detected:

the inflated product can be immersed in water. The hole will reveal itself as a trickle of small air bubbles;
at home, the place of the gap can be found using foam soap solution which is applied to the surface of the mattress. A large bubble will inflate over the rupture site;
several liters of foam solution are poured into the inflated product. Turning the mattress over, you can find how liquid flows out of the defects with a quiet whistle;
it is recommended to sprinkle the surface of the air-filled mattress with flour or any powdered product. Air escaping from the hole will blow off the powder. After a rupture is detected, the mattress is cleaned with a vacuum cleaner;

You can learn more from the video:

IMPORTANT! Usually, damage appears in several pieces at once. The area of the relief pattern is torn the fastest in air mattresses.

The detected defect should be marked with a felt-tip pen or marker.

Need to localize the place (click to enlarge)

Repair of an inflatable product

When choosing how to glue an intex air mattress, it is worth, if possible, using a branded repair kit, which is sold with the product. Manufacturers complete the set with velor patches, special glue and vinyl wrap. How to glue the mattress is described in detail in the instructions. It is included with the set.

If the set is lost or used, you can glue the mattress in other ways. The gluing process can be started only when the product is dry. It is important to choose the right glue to use for these purposes. It is better to use a rubber-based adhesive or other composition that, after drying, retains plasticity. By gluing the patch with superglue, the owner runs the risk of permanently ruining his thing.

Usually, the approach to repair varies, based on the location of the damage.

Elimination of punctures and cuts

The question of how to glue an air mattress is easily solved. The patch can be cut out of a rubberized item or you can use a patch from a tire repair kit.

On the smooth side of the product, the area around the hole is sufficient to degrease with acetone or alcohol. The same tool handles the patch. For mattresses, they are cut out without corners. Glue is applied to both surfaces, which are pressed tightly against each other. The place of repair is placed under the press for 12 hours.

If the mattress is damaged on the velor side, the fluff from the surface around the hole should be cleaned with fine-grained sandpaper. Next, the patch is glued in the described manner. A defect on velor cannot be avoided with such a repair.

Watch the video to find out more:

You can stick an air mattress with wrong side, then on the surface the puncture site will be almost imperceptible. To do this, the area of the defect must be pulled through the opening to inflate the product. The patch is fixed with glue. After half a day, the product can be turned out and filled with air. When thinking about how to seal an air mattress, one must take into account a number of advantages of the latter method: the gap is effectively masked, the patch is held from the inside more securely, as the air that fills the bed presses on it. Although the repair process is more laborious.

Failure to comply with the rules for operating the product leads to the fact that the consumer is often forced to look for an answer to the question of how to seal an air mattress on the seam. It is quite difficult to eliminate the defect of the joints on your own. A patch placed on the seam from the wrong side will not last long. Manufacturers recommend contacting a service center for help.

ADVICE! Electrical tape can be used as a temporary remedy for punctures. The sealed mattress can be used for several days.

Inflatable furniture is simple and convenient to use. Thanks to such products, you can provide full-fledged sleeping places for guests, and make outdoor recreation more comfortable. Careful use and compliance with operating techniques can save you from having to look for an answer on how to seal an air mattress at home.