To make it you will need a sheet of paper approximately A4 size and a ballpoint pen. You can take not only regular writing paper, but also wrapping or newspaper paper (you will need a little more of it). A trapezoid-shaped blank with a base length of 14–15 cm is cut out of paper. Glue is applied along the base of the blank, and a rod is pressed against it. After the glue has dried, the rod is tightly twisted into the paper, and the edges of the paper are additionally coated with glue. Cones are formed along the edges of the product. The lower part of the cone is needed for ease of holding when writing, and the upper part can be trimmed with a stationery knife.
The finished handle can be painted acrylic paint, which does not dissolve in water after drying. You can also cover the pen with colored gift paper or scrapbooking paper, as well as a page from glossy magazine or foil tape. To prevent the paper from being worn out by constant use, homemade pens are additionally covered with transparent tape or varnished.
Wood handle
If you have access to lathe, you can make something unusual wooden case pens. You will need wooden blanks, metal tubes, a rod, a mechanism for the handle, glue and sandpaper.
Don't forget that Decoration Materials may affect the color of the wood. Therefore, test them on waste first - this will help insure against unexpected results.
A saw, a machine, vapors of varnishes and adhesives can be harmful to health if used carelessly, so it is important to remember the safety requirements when working with them.
Syringe pen
A beautiful stationery product can be made from a regular disposable syringe. The nose of the syringe is drilled to the size of the writing unit of the rod. The body is filled with colored gel, rhinestones, and sequins. A rod cut to fit the syringe body is inserted inside. The piston is filled with glue to fix the rod.
Thread pen
A tourniquet is woven from thick threads, and a rod is inserted into the middle. You can take threads of different colors and structures, the main thing is that they are of the same thickness. The plait is woven very simply: one thread is placed on top of the other from the middle to form a square. You can secure the rod in the bundle with a drop of glue.
A fountain pen
To make a handle in old style you need to take a large goose or turkey feather. If desired, paint it any color or several at once. The fluff at the base needs to be cut off and sanded a little with soft sandpaper so that the future handle is comfortable to hold. The tip of the pen must be cut at an angle - it is very hard, and the resulting tip can be used to write.
You can also insert a steel feather into a bird feather and disguise the junction decorative material. A feather made in this way will be more durable. And of course, you can insert an ordinary ballpoint into the pen.
Gel pen
It differs from a regular ball one in that a gel rod is inserted into the prepared flask. The gel aquarium pen looks original. To create it, you will need a transparent tube with a wooden stopper, sealed at one end (something suitable can be found in a pharmacy or chemical glass store).
A hole is made in the cork according to the diameter of the rod; the cork can also be painted with acrylic paint. A mixture of water and glycerin is poured into the flask - the more glycerin, the thicker the filler, and the slower the decor will float in the body. We pour glitter, stars, and foil fish into the flask, insert the rod into the cork and close the flask tightly (for reliability, you can secure the cork with waterproof glue).
2-in-1 pen
To create it you need to take a pen and a simple pencil. Disassemble the pen, cut off a part from the pencil based on the length of the pen, and insert it into the pen body. To adjust the pencil to the diameter of the handle, it must be planed with a sharp knife and sanded with sandpaper.
Insert the pencil into the body and secure with adhesive tape. Next, we cut the rod and assemble the handle. Now the pencil will always be at hand - with reverse side the pen you write with.
By the way, don’t throw away the remaining piece of pencil, it may still come in handy.
And in conclusion - a pen for spy game lovers
A fountain pen—either a regular one or a homemade one—can be filled with invisible ink. Making such ink is quite simple. The only thing is that you won’t be able to pour them into the rod, because they are very liquid.
There are three most common types of invisible ink and three ways to read what is written:
- dilute solution copper sulfate- hold the paper over ammonia
- lemon juice - heat the paper with an iron or lamp
- milk - iron the letter with a hot iron.
A beautiful pen can be bought at any store. But if you are a fan of exclusives and a lover of products self made, you can make a one-of-a-kind pen. A self-made piece of stationery will become a unique designer souvenir for you and your friends.
We have collected the most interesting and creative ideas, how you can turn boring accessories into original ones by decorating them to your taste and color. You'll be surprised how much more enjoyable it will be to use these updated, homemade school supplies even outside of school.
The school year has come to an end and you can forget about school until September. But don’t rush to throw away your boring pencils, pens and notebooks. By spending a little time, you can get either bright and interesting school supplies, which will be a pleasure to keep for your school, which, by the way, can also be designed in a very interesting way, using our ideas.
The simplest pencils, PVA glue and glitter are all you need to give a second life to ordinary school supplies.
Handles decorated with delicate feathers with a watercolor pattern - what could be more original?
By the way, feathers for such pens can be made from paper, coloring it in . Then they will even on paper convey all the lightness and weightlessness of the real ones.
To make such interesting “tassels” on the ends of pencils, you only need decorative paper and thread. Yes, yes, it's that simple! Cover a regular pencil with colored paper or decorative tape, but so that the paper still hangs a little from the end of the pencil. Then pull it with a thread and cut it, making a fringe.
What could be cuter than a pencil or pen with an ever-blooming flower? The trick of this decor, of course, is in, which should be done in advance and attached to the pencil with tape. The pencil itself can be wrapped in green paper to create a twig.
School supplies decor: how to decorate school notebooks
You can decorate your school notebook with a fabric cover. Among the advantages of such covers: they are pleasant to the touch, you can make additional pockets both inside and outside, a variety of textures and patterns and, of course, simple execution techniques. This notebook can be used in the summer as a notepad or personal diary.
Embroidery on a notebook. It sounds strange, but it looks very beautiful and unusual. This decor is suitable for notebooks with plain and soft cardboard covers.
Stamps and drawings with paints can be made not only in a sketchbook, but also on the covers of notebooks, in order to decorate these same school notebooks in this way. Try it and you will like it!
Decorative adhesive tape is also perfect for decorating school notebooks, folders, book covers and albums. Thin strips of tape can be glued straight or diagonally, creating your own special pattern.
You can decorate an ordinary notebook with a photo collage of your favorite photos or pictures for a summer mood. Follow the link - complete.
Girls will especially love this idea for decorating their school supplies. The openwork decor for the notebook cover was created for romantic schoolgirls.
School supplies decor: how to decorate school paper clips and paper clips
To decorate your school paper clips and clips, you can use bright, decorative adhesive tape. In addition, for such decoration of school supplies you will need very little material, and this school little thing will please the eye for a long time.
Decorative adhesive tape can be tied to a paper clip or attached to it in the form of a flag. Such beautiful paper clips can even be used as...
Will look cute as a decoration for school supplies, especially paper clips. These will lift your spirits bright colors and decorate the school office in an original way.
Watch online how to decorate school supplies with your own hands
Now you have enough ideas for decorating yours. These and other ideas on how to decorate school notebooks, pencils, pens and other useful stationery will help create the mood for the summer and will be useful when preparing for the new school year.
Make it beautiful a simple pen and making it original is easy. The most original ideas that can only come to your mind.
To make a beautiful pen you need to take the pen itself, decorative material and glue. You can decorate it by wrapping it with a narrow satin ribbon, attaching a flower or a bow made of paper or fabric to the top edge. Get original designer item. Such a pen can be an interesting gift made with soul.
The idea of weaving a handle with multi-colored threads using the macrame technique, and if also with an original weave, is a chic option for a stylish girl.
You can decorate your pen however you like with any beautiful things, rubber bands, stickers, feathers, rhinestones. Anything you want.
What can be made from a pen
The body of a ballpoint pen can serve as a material for various crafts.
- Can be done original stand For mobile phone. To do this you will need four to five pens and rubber bands for money. Twist the three handles with a rubber band to create a stable tripod. Screw one or two handles horizontally to the two legs, depending on the thickness of the phone. Install the resulting structure slightly at an angle and place the smartphone on it. Watching videos is very convenient and hands free.
- Of pen and four simple pencils can be done . From pencils, use rubber bands to assemble a base in the shape of the letter “T”. Attach old pen along the bottom of the letter. The function of the bowstring will be performed by an elastic band. You can use old empty rods as arrows. The toy for boys is ready.
Many probably remember multi-tiered chandeliers with transparent plastic pendants. - You can do it using the same principle. You will need a plastic circle attached to the lamp, and a lot of multi-colored transparent pen housings. Stationery secured in a circle using wire or paper clips. When you turn on the lamp, the lampshade will look like crystal and scatter multi-colored light.
How to make a pen with your own hands
How to make a 3D pen with your own hands
Such a handle can be made from ordinary glue gun. First you need to disassemble it and remove the pushing mechanism; it is better to saw off the lower part of the pistol handle. Then you need to reduce the outlet hole. You can put a paper clip in there and tape it so it doesn't fall out. The next step is to attach a mini fan, these come in different devices and are sold in stores as spare parts. Small alligator clips are attached to the fan wiring; we will use them to connect the battery. Now you need to attach the crown battery to the bottom of the gun. Use plastic clamps and glue to secure all parts. That's all - your 3D pen is ready. You can try drawing.
For a fountain pen you need the pen itself. You can take turkey or goose, they large sizes. Paint with dyes in any color you need. Can be in several colors at once. The feather cover above the base must be removed to make it easier to hold when writing. Using a sharp knife, cut off the bottom of the feather under the cone. It is very hard and you can write with the resulting tip.
You can also use a calligraphy pen. It needs to be attached to the prepared turkey feather, and the joint should be decorated. A pen made this way will be more durable.
DIY gel pen
- You can make a gel pen just like a regular one. Any materials can be used as a housing for the rod. Just insert the gel rod into the manufactured flask.
- Gel pen - aquarium, very interesting option and the rod can be changed. To make this you will need a transparent flask with a wooden stopper. We make a hole in the cork to the size of the gel rod. The cork can be painted if desired. Pour water into the flask and add glycerin. The more glycerin there is, the slower the decor inside will float. Pour into a flask filled with liquid, various sparkles, stars and, of course, foil fish. We insert the rod into the stopper and close the flask with it. Handle - the aquarium is ready.
How to make a pen out of paper
A pen made of paper can come in a wide variety of colors. To make it you will need an A4 sheet and a rod. Cut part of the sheet at an angle so that when you twist the rod, you get a beveled nose. We take the rod, coat it with glue, when it sticks tightly, we begin to twist it tightly. At the end we coat it with glue. You can color the pen however you like. You can draw various patterns. Be sure to varnish the pen so that the paper does not rub off during use.
The rod in such a pen will not change. Finished, make a new pen.
How to make a pencil pen
To create a two-in-one pen and pencil, you will need a pen and a simple pencil. Let's disassemble the handle. Cut off half of the pencil, less if possible. Now you need to insert the pencil part into the pen body. Naturally, it won’t fit there, so you need to trim it a little with a stationery knife. We inserted a pencil and taped it tightly with electrical tape. Now we cut the rod from the handle to insert it into place and assemble the handle. Now you don't need to look for a pencil to draw something, you will always have it on the back of the pen you write with.
Don't throw away the rest of the pencil, you will need it next time.
How to make an invisible pen
To make an invisible handle, you first need to make. Making such ink at home is not difficult. To do this, you will need a diluted solution of copper sulfate. It has a slightly bluish tint; if you write something with it, it won’t be visible. To read such a letter, you can hold the paper over ammonia.
You will have to write with such ink using a fountain pen, since it will not be possible to pour it into the rod. And if someone manages to do this, they will still leak out because they are very liquid.
Spy ink can also be made from lemon juice; it appears if the letter is heated strongly with an iron.
How to make a pen write
If suddenly your pen stops writing and you still have a lot of ink, you need to do the following.
- Disassemble the pen, pull out the writing tip and blow from the other end. Perhaps there were just air bubbles there.
- Without disassembling the pen from the end with which you write, use a suction motion to pull the ink toward you. It also helps a lot and you won't get dirty.
- You can simply breathe on the writing tip; perhaps the ink has thickened a little. Warm breath will make them thinner.
- A radical solution is to replace the rod; it could be defective.
Good day, brain friends! You might be interested to know about brain process creating an elegant ballpoint pen that I made for my wife the other day.
This is going to happen brain pen from paper and epoxy resin in a technique known among knife makers as “getinax”.
Creating handles is a fairly common activity for carpenters who have special kits and tools that are becoming increasingly affordable. (Included tools, such as the pen core, can easily be used for other purposes and expand your DIY capabilities). In that brain leadership I use the fine pen set.
My wife (just three weeks ago we said “I do”) has joint problems and has found that the ergonomic shape of a ballpoint pen is very helpful in avoiding pain, which is why I have topped my crafts I added a fairly large ball.
Step 1: Cutting Paper for the Pen Body
For your homemade products I chose several large sheets of paper in different but complementary colors (dark green and cream) and folded them together before using a jigsaw to cut them into 2.5x2.5cm paper squares.
During this brain procedures, and always, it is important to follow safety precautions! I found for myself safe way cutting paper - press it between two wooden blocks, and thus hold it on the jigsaw table.
You can also cut the paper with a knife or scissors, but whatever method you choose, be careful.
Step 2: Create a Jig for the Handle Body
I put together a small device - a jig that will help organize the paper squares while gluing them. This jig is made from two blocks, arranged in the shape of the letter L, and nailed to plywood.
Step 3: Gluing the handle body
This is the main and long stage of everything brain process.
The paper squares are glued together using epoxy resin, and during the gluing itself, the surface tension of the resin and paper holds the squares together, preventing them from falling apart.
My main concern was that the diluted epoxy would harden before I could finish the gluing process. crafts. Fortunately, if you dilute it in small quantities, you have more time to glue the squares, so I had time.
I believe that experiments with various adhesives and resins can speed up and make the gluing process easier than in my experience.
Step 4: Cutting out the body shape
And now the fun begins.
After the glued body blank is separated from the jig (I did this with a jigsaw), it’s time to determine where to cut it into pieces.
In the past I used a lathe with a long brain drill for drilling a through hole in the case, which is very convenient if this case has a beautiful wood pattern and it needs to be perfectly aligned. But in most cases it is still easier to use a drilling machine.
Before cutting with the jigsaw, I marked the cut lines using copper tubing.
Step 5: Drilling a Hole in the Case
Fixing the body blank crafts in a vertical position, I drilled with a 7mm drill through hole. But this is for my “handle assembly kit”; yours may require a drill of a different diameter.
Step 6: Gluing the Tubes
I sand copper tubes to increase the gluing surface area, and also to remove dirt and grease, which can reduce the quality of this brain glues.
I applied cyanoacrylate/medium density superglue into the hole in the pen body and onto the copper tubes that came with the kit. The trick is to not stop while inserting the tube into the hole. As the tube slides over the hole, the glue acts as a lubricant, but when it stops it quickly bonds. It is ideal to have the tube completely placed in the body of the workpiece upon completion.
To push the tube into the housing homemade products you can use a pencil or something similar.
***Tips from the comments***
@Scanner2 writes:
After gluing the copper tube into the body, it is possible that some glue will remain inside the tube. To remove it, I use a 6mm drill, which I turn in the opposite direction, thereby drilling out the tube. The reverse direction does not engage the tube material, but passes through it.
(Excellent tip - I would add that depending on your "set" and the way you strip the copper tubing, it may be helpful to run a file along the sharp edges of the tubing, which will reduce the likelihood of the tubing catching on the body and make it easier to connect the handle when previously it comes).
Step 7: Trimming
My “handle assembly kit” came with a trimmer.
I clamped it in a lathe chuck brain machine and put it on his pin copper tube blanks to blades that remove excess material around the tube. The result was completely flat surface for a liner installed later.
If you don’t have such a trimmer, you can grind or cut off the outer surface flush with the copper tube.
Step 8: Connecting the blanks and forming the profile
The prepared paper blanks are put on the core with an insert of the appropriate size between them.
In my case, the liner is thin, "slimline", although there are many other styles to choose from.
After that, I began to form and finalize the shape of the handle using various instruments. For more full review turning tools and working with them, I have prepared a short guide for one magazine, and you can familiarize yourself with it.
Step 9: Finishing and Polishing
Before application finishing coating on under the tree, I wanted to make sure the shape of the handle was “perfect.”
Once I was satisfied and sanded with 1000 grit sandpaper, I applied a thin layer of superglue, spreading it evenly with my finger. The main thing here is to apply enough; with a small amount, the glue will not lubricate the surface during its distribution.
So I applied it to brain pen four coats of superglue before sanding it with 1500 grit sandpaper and buffing it with polishing compound to bring out a mirror finish.
Cabinetmakers call this process rubbing, which results in a flawless, satisfying look that takes a lot of effort to achieve.
Step 10: Handle Assembly
The components in the kit like mine have a friction fit, but can easily fail if you are not careful.
I have found that it is better to dry assemble the kit to get an idea of the position of the components in homemade and work out order brain assemblies. For example, if you do not install the tip of the pen before the mechanism, there may be problems. I used a vice to press the parts in and get a good fit.
I would also recommend finally getting high quality ink for your pens, because regular ink is usually just good, but not the best. All Cross style pens have essentially the same mechanism, so you can successfully use the same ink as people who have spent a lot more than you on their pens, plus the cool thing about having one of a kind. kind of a pen, and which you made with your own hands.
That's all, everyone brain success!
