How to disassemble the knob handle of an interior door. How to disassemble a door handle for repair or replacement. How to remove and disassemble the door handle of an interior door

How to disassemble a round door handle-knob? This question interests many owners when entering new apartment, where door leaves with a non-removable handle mechanism are installed. In this case, to remove this element from the door leaf, as a rule, the following steps are performed:

The fastening bolts on one side of the door leaf are unscrewed.
The mechanism is removed through the holes in door leaf.This is what a round knob looks like
Next comes the analysis of the fittings, which consists of an additional striker plate.
To remove such elements, simply pull them towards you.

An element such as a non-separable round handle is attached using conventional fastening bolts. The mechanism is designed in such a way that it will not be carried out later renovation work, and a new cover will be immediately purchased and will take the place of the old handle.

It is worth noting that this process is associated with the purchase and replacement of a mechanism; otherwise, there is no point in removing and attempting to disassemble such an element.
Since the manufacturer did not provide options for repair and installation of the handle after repair in its original place.

Round with rosette

Now let's look at how to disassemble a round door handle. The principle of operation is very similar, but the main difference lies in the method of removing the decorative turning part. If there is no hole for a key or screwdriver on the side of the handle, then you need to manually separate the elements. To do this, hold the handle on one side of the door motionless, and turn the other part and remove it from the thread; you may just need to pull it towards you.

After that, remove the socket in the same way and unscrew the screws. Remove the axle and proceed to other elements: lock or latch, if necessary

When removing decorative parts, it is important not to overdo it so that some elements of the mechanism do not burst.

Round door handle with rosette

In order to disassemble the round knob handle, you will need an additional special key to clamp the spring mechanism.

The key included in the kit may not be the right length; in this case, it can be replaced with a nail or other thin object.

First, remove the decorative trim from the top. Using a wrench or nail, move the spring-loaded pin, inserting the tool into the access hole on the side, while simultaneously pulling the handle and removing it along with the cap. After this, you need to pry the latch of the decorative flange and remove it too. Then unscrew the mounting screws on the plate. Now you can completely disassemble the handle and remove both parts along with the axle.

As you can see, there is nothing complicated. In order to assemble the handle, you need to perform all the manipulations in the reverse order: first, install the lock and fix it with a plate, then insert the axle and put on the fasteners, and only then assemble the decorative parts. Don’t forget that you first need to thread the decorative flange, and then put on the pressure or rotary part itself.

Need a master? Professional craftsmen will perform any work Order repairs

Remedy for psoriasis

Types and design of door handles

Modern production offers the following types:

Fixed (stationary) - the most common. But they are the most inconvenient and impractical. They are a bracket of a certain shape (rectangular or arched) attached to the door leaf. Repairing them involves moving them to another location or replacing them.
Push is a device L-shaped, which is attached on both sides of the canvas. Its mechanism is mounted inside the door leaf and has an external tongue, with the help of which the door is fixed in doorway. To open such a mechanism, you need to press the handle.
Round is a combination of a spherical handle with a lock, mounted on the door. In practice, it is often installed in interior doors - only small percentage their models are designed for installation on entrance doors– most often they lack protection against hacking.

Removing the round handle

Round handles can have different designs and they are removed in different ways. One of the simplest options is shown in the image. In fact, no explanation is required - we unscrew the two tightening screws, after which the handles with the entire mechanism can be removed. And by unscrewing the screws from the end side of the door, you can remove the latch.

However, sometimes not everything is so obvious - there are round handles with a button and decorative elements that hide the fastening screws. To gain access to them, you need to remove the outer part of the handle, which is fixed with a special button, and then the decorative trim.

How to remove a round handle with a button

The buttons that secure the outer part of the handles may also differ in design - sometimes they are clearly visible, in other cases only a hole is visible. Our task is to find the locking button and press it. Go!

On the handle of the INSIDE of the doors we find a button or hole under which it is hidden. If the button is not visible under the hole, then you should twist the handle in different directions until the hole aligns with the button.

Having gained access, press the button with a handy object - a nail, a thin screwdriver, etc. Having sunk the button, remove the outer part of the handle, turning it a little from side to side and moving it away from the door (pulling it towards you).

Note. Sometimes it takes some effort to retract the button, especially if the handle is oxidized or clogged with compressed dust. When applying force, be careful - the tip of the screwdriver can easily come off the button and scratch the handle. The further path of the screwdriver is easy to trace - it will stick into the palm or finger of the other hand holding the handle.

The outer part of the handle was removed (its slight oxidation is noticeable in the photo), let's move on to the next step.

Now you need to remove decorative element in the form of a cover that hides the mounting screws round pen. To do this, pry it off with a thin metal object - a steel technical ruler, a screwdriver with a wide but thin blade, or a similar object. Prying should be done very carefully, trying not to scratch or damage the coating of the door leaf. It is advisable to place a thin metal plate under the prying object - a blade, for example, and only then remove the decorative trim. You can secure the plate to the door leaf with electrical tape or tape.

Note. Some types of linings have special places for removal in the form of recesses into which the tip of a screwdriver is inserted. If the recesses are semicircular in shape, then it is advisable to pry the overlay with a round-shaped object - in as a last resort Phillips screwdriver. Typically, the removable places are located at the bottom of the decorative trim, and not on the side.

Having removed the decorative trim, all that remains is to unscrew the screws holding the lock ladles together. The handle has been removed.

As additional information, we note that the above method can be used to remove the vast majority of knobsets with both round and staple-shaped handles. The shapes of the buttons in the images are the most common, but they can look different.

Another button option.

And this form happens...

And this one too - in the form of a bracket...

That's all! We hope our instructions were useful to you, and after removing the handle, your doors and hands remained intact :)

Handle disassembly

Typically, a door handle has a fastener that holds it to the door, and before you disassemble it, you need to remove the fasteners.

Handles are usually attached to an interior door in the two most common ways.

Firstly, on the screws. When the base of the fittings is screwed to the canvas.

And, secondly, for one axial rod. This method is often used in push and turn structures, when the fittings are directly assembled and fixed to the doors by screwing its elements onto the threaded axis.

Fastening with self-tapping screws. It can be easily removed from the door using a regular Phillips screwdriver or screwdriver.

It is important that before you start unscrewing the fasteners, you need to remove paint and dirt from the screw head, and it is better to lubricate the place at the fastening point with silicone grease. Without these simple manipulations, you can simply rip off the crosspiece and unscrew the screw, it won’t work

Stationary handles are usually attached to screws; after removing them, the fittings are removed from the canvas. How to remove handles from interior doors if they are assembled on a rod?

In the latter case, the fasteners are dismantled and the fittings are disassembled simultaneously.

Push types

First you need to unscrew the swing arm mount. Usually it is located on the side in the form of a screw. It is unscrewed using a screwdriver (flat or Phillips, rarely hex).

Afterwards, you need to remove the cover; it can simply be pressed with a lever, or be on a thread.

Removing the decorative cover will reveal the main fastening, usually small bolts with a flat head screwdriver.

By unscrewing the fasteners, the internal mechanism is easily removed from the socket.

If the design has a lock with a tongue, it can be additionally secured at the end with a plate on self-tapping screws. In this case, they are unscrewed and the mechanism is removed from the groove of the door edge.

Rotating devices (knobs)

Knobs or rotary structures are equipped with a lock. They are disassembled in the following way.

First of all, the pads are removed from the rotary round handle.

Underneath there is a stopper that needs to be unlocked with the key included in the lock package. If it is missing, you need to use an object that fits (for example, a nail).

Press the handle on the stopper and pull it towards you, opening the mounting screws. They are being twisted. The mounting plate is also removed from the end. After which, holding the entire structure with reverse side, removed from the nest.

There are also stationary types of handles that do not have external fastenings in the form of screws. Their installation is also simple, and they are easy to dismantle.

They are mounted on a threaded bolt through through hole in the door leaf. To remove this type of fittings, you need to firmly fix the handle on one side (you can just use your hands) and turn the other counterclockwise. It will begin to unscrew. After this, the axial fastening is pulled out from the hole in the canvas.

The disassembly technology itself is very simple and does not involve the use of specialized tools. The main thing is to correctly determine the type of handle and understand the principle of its fastening.

How to remove and disassemble the door handle of an interior door

Have you ever wondered how many times a day you open and close the interior door in your apartment? Most likely no. Moreover, all our actions are performed here so mechanically that we do not pay any attention to such elements as ordinary door handles. Until something happens to them

As soon as some kind of breakdown occurs, we not only begin to pay attention to the fittings, but also understand how important role she performs in our house.

Unfortunately, no matter how high-quality and expensive door hardware is, it needs to be replaced from time to time. The reason for this can be either unexpected breakdowns or the usual desire to slightly update the door design.

For dismantling work to be successful, it is important to know the basic rules for disassembling door handles, of which there are several types today.

How to easily remove and disassemble a door interior handle

A broken door handle and the desire to replace it with a new one are the most common reasons that force us to pick up a screwdriver and get to work. But before you do this, you need to carefully study the mechanism of this hardware.

Disassembling the stationary handle

In this case, let's start analyzing examples with the rules for disassembling an ordinary stationary handle, which do not have a push set and a mortise lock for a counter cylinder. Here we need a flathead or Phillips screwdriver or a screwdriver with a bat. Let's look at an example of parsing a regular stationary handle:

First of all, you need to loosen the screws that hold the mechanism together.
If there is any decoration, you should first get rid of the decorative part by carefully removing it from the surface of the element.
While gradually unscrewing the bolts, it is necessary to hold the counter part on the back side of the door leaf, otherwise the element may fall and become deformed.
The fastening can be one-sided or on both sides. You should make sure of this in advance before starting work.
After the screws are unscrewed, use a flat-head screwdriver to carefully remove the handle from the door leaf.

In the case of a stationary handle, the entire disassembly consists of removing the decorative trim and unscrewing the fasteners. Next, a new mechanism or an old element with new fasteners is installed in its place.

Handle disassembly process

It is worth noting that replacing a stationary handle with a new mechanism requires additional manufacturing of the corresponding fitting grooves in the door leaf.

Lock removal and repair

Repairing interior door locks is difficult. The causes of malfunctions are different.

When using cheap, low-quality silumin door fittings, the 4-sided pin may break. The solution to the problem is to purchase a steel mechanism from trusted manufacturers and completely replace it.

A common problem with locks is the tongue not working properly. This is possible with a short pin. The square can move in the direction of the latch, pressing it, reducing operation.

Repair work on locks is carried out as follows:

A long pin is purchased and the length is measured.
Using a grinder, it is shortened to the required size.
Then you need to disassemble the lock interior door.
The square is changed, door fittings are installed.

When installing the handle, the base must cover all the holes that remain from the previous mechanism.

A lock with a handle can be replaced or repaired even by a novice master who knows how to use available tools.

Types of mechanisms

Door handles are mounted different ways depending on their type. The following mechanisms are usually used:

Rosette or push-type - the lever is made in an L-shape. Easy to install and maintain, do not require special hole preparation. The mechanism is closed with a decorative cover.

Image from dverlife.ru

Knobs are the name given to ordinary round-shaped door handles with a latch or keyhole in the middle. It looks quite nice in the interior, you can’t get caught on it, but the mechanism of such a product is quite delicate and quickly breaks down.

Round with a rosette - approximately the same in size appearance, like nobs, but differing in structure. They do not have a locking latch, but in its place there is a decorative plug, under which there is a fastener.

When choosing a handle, be guided by your design preferences and personal opening experience. Interior fittings are generally quite durable and can withstand daily use, and their main purpose is not to prevent penetration (as at the entrance), but to ensure maximum ease of use.

What do we need

Before installing handles on interior doors with your own hands, you need to prepare workplace(the operation is quite dusty) and some tools. We will describe a set that will be comprehensive for installing any door hardware: for simple mechanisms you can limit yourself to only a few of them.

To install interior handles with your own hands, we will need the following tools:

electrical: screwdriver (or screwdriver), drill;

mechanical: hammer, clerical or sharp kitchen knife, chisel;

fasteners and accessories: angled ruler and pencil, awl, tape measure, self-tapping screws, drills and crowns of various diameters;

You can also use a jig - this is a tool for precise marking. This is not necessary but will make the process much easier.

How to remove a door handle from an interior door

First, you will need to determine what type of door mechanism you have in front of you. This is a necessary point to decide on the tools and progress of work. Next, we will talk in detail about each specific type and discuss small nuances of work that can become pitfalls.

Push mechanism

As mentioned earlier, this is the most popular type of door handle model for interior doors. It will not be difficult to disassemble it and in the process we will only need one tool - a screwdriver. In some cases, a hex wrench may come in handy, so it’s better to have that in advance as well.

We unscrew the handle itself, the outer part of the lock.

When you have already removed the pressure element, you can see a recess with a countersunk screw - unscrew it with a screwdriver and remove it from the axis. It is at this stage that sometimes you have to use a wrench instead of a screwdriver.

Next, remove the decor that masks the mount itself. The trim has a thread in many models - we simply turn it.

When the decorative trim is unscrewed, the screws become visible - we carefully unscrew them and pull the entire mechanism towards us. This action should be performed as carefully as possible - hold the handle on the back side of the door leaf.

Remove the rotary axial element.

If there is a need to dismantle the latch or lock, perform the same sequence of actions, but in addition to everything, you also unscrew the lock plate at the end of the door, and then remove the device itself.

The main feature of the handles of this model is the presence of a tetrahedral lining and a latch tongue. When you have completely removed the fittings, look at what the handle was attached to. Sometimes a rod passes through a hole in the tetrahedral rod and an identical hole in the handle itself. Then you just pull it out and take out the handle without complications. Of course, the trim on the other side of the door leaf is first unscrewed.

Rotary

Let's figure out how to remove the rotary handle from an interior door. Since the principle of operation of the mechanism is very similar to the previous model - push-type, the difference in the dismantling process is small.

However, there is one nuance that distinguishes these two locking devices. Removing the decorative rotating part, which even visually distinguishes them from each other, requires painstaking work.

If you do not see the key hole on the side, separate the elements manually. At the same time, the handle must be held motionless on one side, and on the other, rotated and removed from the thread. Sometimes you just need to pull it to the side to do this.

In the same way, remove the socket and unscrew the screws.

We remove the axle and begin to remove the remaining parts, if necessary.

Be careful - if you apply too much force, for example by twisting, parts may be damaged.

Want to know more? Watch a video on how to remove the door handle of an interior door:

Knob handle

This is the most difficult model to install and dismantle. However, if you follow some rules, this work will not cause you any difficulties. Stock up on a key with a stop, a Phillips and a flat-head screwdriver - just in case, because you do not know in advance what the fastener will turn out to be.

Using a flat-head screwdriver, pry up and remove the trim that goes in a circle near the door handle.
Then we use a key, or any flat object (you can take a wide knife) - press the stopper, so the handle is pulled back.
We remove it from one side and unscrew the screws from the inside.
Now we remove both handles from the door.
Unscrew the screws that hold the latch.

When working on disassembling the knob handle, be careful and hold the part on the other side of the door leaf.

When there is no need to completely replace the lock and you just need to turn the handle in the other direction, you need to place the latch in the door leaf itself with the beveled end in the direction where the door is supposed to close. This part is screwed on with screws. Then we insert the handle with the locking mechanism, after which the clamping part is secured on the other side. We secure it with two screws.

After this part of the work, you need to put on the decorative strip and install the remaining element. The rod should stand up straight - to do this, turn the lock until the slot and the rod coincide.

At the final stage of work, you need to put on the handle and secure it.

To learn more about the process of dismantling this handle model, watch a video on how to disassemble an interior door handle:

Disassembling a round handle with a rosette

A socket, as a rule, refers to a mechanism that allows you to lock a lock using a special small key on one side and an accessible thumb on the reverse. In this case, disassembling such a mechanism consists of the following steps:

with your own hands you need to loosen the screws that hold the decorative trims on both sides;
Next, you should unscrew the screws that connect the mechanism on both sides;
after this, the remaining part of the handle is removed from both sides;
Then the lock itself is removed.

If the handle requires repair or replacement of a certain mechanism, then you will have to completely disassemble the individual parts and find the cause of the malfunction.

Important. When disassembling a round handle with a socket, all fastening elements must not be lost, otherwise you will not be able to put the mechanism back together and install it in its original place after reassembling and replacing one of the parts

Watch the video: door handle repair.

Door handle classification

These devices can have quite a variety of forms, but are divided into two large groups.

Stationary - have no connection with the lock and are installed as independent device. The handle serves only to grasp it and open or close the sash. It is usually attached with screws to almost any surface. The design of the handle can be very diverse. The most popular form was and remains U-shaped, in the form of a bracket, which is fixed vertically. If there is still a need to restrict access to the room, a roller latch is mounted on the sash from inside the room. The photo shows a stationary view of the fittings on an interior door.

Push ones - their mechanism is somewhat more complicated. The presence of a latch requires cutting into the door leaf and forming a corresponding groove in the frame. When pressed, the spring moves the latch tongue and the door opens. When the handle is free, the latch is in the extended position and the sash can simply be slammed shut. This method ensures a tighter fit of the sash to the frame, which means higher sound and heat insulation of the room.

The mechanism provides the possibility of emergency opening: with front side There is a slot that allows you to use a screwdriver or other flat object to open the locked door.

Push ones are divided into two categories.

With a one-piece pallet cover - mounted through a lock. You should pay attention to the axial rod on which the fittings are placed - it should be equal to the thickness of the door leaf. The length of the element can be adjusted. In the event of a breakdown, the entire mechanism must be replaced. The photo shows a sample.
With separate escutcheons – installed with or without a lock. What matters here is the size of the pads and the size of the key hole.

Knobs are round shaped handles that are a type of push handle, but can also be known as rotary handles. The action is similar, but to open the door you need to turn the knob. Usually the mechanism is equipped with a locking button, pressing which allows you to turn the ball on the other side of the interior door and open it. For emergency tearing, there is also a slot on the front side of the device. In the photo there is a handle-knob installed on an interior door.

Why disassemble the handle

Since these models of door handles are disassembled quite simply and according to a similar principle, anyone can learn how to do this without any problems. But disassembling and assembling handles is not a routine process; the need for this does not always arise. What could lead to such a need?

Breaking. This is one of the most common reasons, this is especially true for cheap Chinese products. Over time or due to rough handling and ignoring preventive measures, the mechanism wears out and some of its parts fail, so it is necessary to carry out timely repairs to the fittings.
Replacement of an outdated model. Every year new product models enter the market and it makes sense to replace old models with more advanced ones in technical and aesthetic terms.
Repair. When renovating a house, most often the interior changes radically in style, so old pen the door may not be suitable and then it needs to be disassembled and replaced.
Scuffs. The lower the quality of the decorative coating, the sooner such a handle will become unusable due to the appearance of abrasions, peeling paint or chips on its surface. It is better to replace such fittings if you do not want to spoil the overall impression of the room.

During long-term use, the handle mechanism often fails.

Disassembling handles

When is it necessary to disassemble the handle?

Self-disassembly of the handle may be required:

when the latch mechanism creaks or jams. In this situation, it is enough to lubricate all working elements. For lubrication, machine oil or a special mixture of WD-40 is used;
if the device is inoperable due to a long period of use or lack of careful treatment and periodic maintenance. All door handles require regular inspection and timely lubrication of moving elements, which increases the service life of the product;
for current repairs, for example, by replacing the latch or tightening the fastening bolts that secure the device to the door leaf;
to replace the handle with a newer or more advanced model. New models are constantly appearing on sale, which can serve as a piece of furniture or have a greater degree of protection.

How to disassemble an interior handle for repair or replacement? To do this, you need to read the following instructions, which were developed by experts for the most popular types of pens.

Replacing stationary handles

To replace the stationary handle, you need to unscrew the fixing screws, which can be located:

on the front of the handle;
under the decorative trim.

To remove the decorative trim, just carefully pick it up on one side with a sharp tool.

Stationary handle fasteners

Disassembling rotary handles

To disassemble the round handle, you need to prepare:

special wrench to loosen the locking pin. The key comes complete with a handle. If special device lost, then you can use any hex key that fits the diameter;
screwdriver

The handle is disassembled as follows:

On the decorative trim you need to find a hole for a hex key. It is most often located below or on the side;
The key is inserted into the hole and pressed lightly. In this way, the locking pin is loosened;
The other hand removes the handle. To do this, just pull the device towards you;

The process of disassembling the rotary knob

at the next stage, the decorative trim covering the hole in the door leaf is removed;
Under the cover there are mounting bolts that need to be loosened using a screwdriver. After performing this operation, the door handle splits into two parts.

Location of door handle fasteners

If you need to replace the rotary knob, you will also need to remove the latch. To do this, simply unscrew the fastening screws located on the end part of the interior door and fixing the corresponding mechanism.

Removing the latch mechanism

Disassembling lever handles

To disassemble the handle with a pressure mechanism, you will need a screwdriver that is most suitable for the mounting bolts.

The disassembly process is carried out according to the following scheme:

The first step is to remove the decorative trim. The cover can be attached in two ways:
- using thread. To remove the element, you need to turn the cover several times counterclockwise;
- using a locking tab. To remove the cover, you will need to move the tongue slightly in any direction with a sharp tool;

If, due to contamination or damage, the cover does not come off, you can use a screwdriver and a hammer. A screwdriver is inserted between the trim and the door. Hitting the screwdriver handle with a hammer allows you to move the mechanism and unscrew it completely.

the next step is to unscrew the bolt located at the bottom of the handle. Using this fastening element, the handle itself is fixed to the mechanism with a latch;
under the decorative cover there are two or three screws that secure the main mechanism;

Lever handle fastening elements

After unscrewing all the fasteners, the handle can be pulled out freely.

Removing the handle from an interior door

The locking mechanism of the push handle is removed in the same way as handles with a rotary system.

After familiarizing yourself with the proposed diagrams for disassembling door handles, you can repair or replace the device without the help of a specialist. To install the handle, you can follow the instructions included with the new device or perform all the steps indicated in the diagrams in reverse order.

To disassemble the push-type locking mechanism, you must first remove the handle. You need to find a recessed screw on the side or bottom of it and unscrew it with a screwdriver (in some cases you will need a hex wrench). Then the decorative trim is removed. Most often it has a thread, and it is easy to do. Having removed the socket that hides the fastenings, you can unscrew the main bolts holding the mechanism. Next, the lock plate is unscrewed from the end side of the blade. The lock can be easily removed by pulling it towards you.

The process of disassembling a device with a rotary round handle differs little from actions with a push mechanism. In some models, the ball has a thread; you just need to hold the second handle motionless while turning the part to be removed in the opposite direction. Sometimes manufacturers provide mechanisms with screws hidden in small recesses, like in pressure devices.

What you need

The list of required tools will depend on the type of handle. The basic set includes: Phillips and flathead screwdrivers, hexagons, pliers. You can speed up the unscrewing process by using a screwdriver with a set of bits.

To make it easy to unscrew bolts and screws, you can use silicone grease in the form of a spray (WD-40). It can also be used to remove rust and restore door handle mechanisms to working order.

More detailed list what may be needed for the job can be clarified after inspecting the fittings. For example, some types of locks may require a non-standard torx or hex screwdriver. Also, for the round rotary handles in the package, you need to find a key to unlock the fastening stopper.

Lever handle

The push structure has an internal mechanism that connects it to the locking tongue. As a rule, these are “L”-shaped products. When you press it, the tongue disappears into the doorway and the door opens freely. The deeper the tongue goes into the hole in the doorway, the more pressure you need to apply. Accordingly, a design that does not require deep pressing is more convenient to use. The fastening is done on both sides of the door at once. General procedure for removing a push-type product:

Remove the main part. There is usually a bolt or screw on the bottom of the handle that needs to be unscrewed.
It is necessary to remove the decorative trim, which hides the screws securing the main part of the structure. The cover plate is in most cases attached using threads.
Unscrew the screws and pull the part towards you, holding the fastener on the other side of the door leaf.
Having removed the structure from both sides, you can begin to release the lock.

Kinds

Before disassembling, find out what type of fittings are. It is divided into 3 categories: knobs (round), stationary and push. The latter are used everywhere. If you press the handle, the latch goes inward. Without pressure, the element is extended.

The mechanism is installed if available mortise locks. On the outer part there are linings that protect the handle from damage. Removing accessories requires care. You need to know the location of the latch.

Round models are installed in rooms that can be locked from the inside (more often found in the bathroom). Made in the shape of a ball. The castle is located in the middle.

Important! The keyhole can only be opened with a key on one side. On the other there is a latch.
. Stationary ones are held on the door leaf with self-tapping screws or self-tapping screws

They have roller latches. The fittings are made of strips with brackets.

Stationary ones are held on the door leaf with self-tapping screws or self-tapping screws. They have roller latches. The fittings are made of strips with brackets.

What types of handles are there for interior doors?

We will not talk about structures that are very difficult to install and disassemble yourself - magnetic devices, electromagnetic and electromechanical. The most commonly used in everyday life are simple mechanical handles; they are the most advantageous because they have long term service and a very reasonable price. But mechanical pens are divided into three types:

Stationary

Do you remember what handles were installed in villages? When they weren’t locking themselves out from anyone and there was no need for a lock. A stationary mechanism is its absence. Such a handle is needed only to move the door leaf, opening and closing it. It could be two individual element fittings or one connected by a common axis. The convenience of this option is that with different style solutions of the space that is delimited by the door, you can make the handle a stylish element.

Push

This type is becoming more and more popular in Lately. This design has the shape of the letter L and is attached to both sides of the door. The mechanism works when pressing on the main part - the halyard tongue is set in motion and the door opens.