All options for creating a stand for a smartphone from a plastic card. DIY phone stand: how to make paper, wood Smartphone stand made of wire

Homemade stand for a smartphone made of mahogany.

Hi all! Today we will do for mobile phone in the form of a dog - a symbol of the year.

Now you need to make a stand for it. To do this, we cut out a circle with a diameter of 70 mm from wood. Sand it down with sandpaper.

We take a few gears that are so small.

We also take epoxy and hardener.

We take plasticine and apply a thin layer on one of the sides of the internal cavity of the figurine and glue it with polyethylene on the same side.

We knead the epoxy glue according to the instructions and pour about 2 mm into the cavity of the figure. This will be the first layer. We are waiting for the solidification of this layer. Then lay out our pattern of gears and fill in the rest.

Our dog is dry.

We remove plasticine. We take sandpaper and bring everything into a divine form.

We mark with a pencil on the figure the point where the hole will be.

Drill make a small indentation.

Now we make a wooden chop that will fix it all. We insert the chopstick into the stand, spread it with PVA glue and also the lower part of the figure with a thin layer so that the glue does not protrude. We connect. Leave until completely dry. Next, we rub our entire product with herbalist impregnation.

Here's what we got.

How often, being at home, in the office or on the road, we cannot remember where we put our phone. To prevent this from happening, you should get comfortable and ergonomic stands that you can make yourself. A phone stand can be made with your own hands from the most unexpected materials at hand. How to do this, our step by step wizard Class.

How to make a do-it-yourself phone stand: options for office and car

Whether at work or in the car, we all need to always be in touch. At the same time, you don’t want to spend a lot of money on expensive coasters, because they can be made from waste and outdated materials.

The simplest option for a phone holder is a card holder. To make it, you need to carefully bend the unnecessary plastic card in two places, as shown in the photo below, preventing it from breaking.

Experience shows that the stand plastic card is very reliable and withstands even air travel at the time of strong turbulence.

To make a phone stand from stationery clips or from binders, as they are also called, you will need one large and one small clip. The legs of the small clamp should be placed between the holding part of the large clamp and put the resulting design on the table so that the clamp bigger size rested on its surface.

Similar coasters can be made in five minutes from clothespins.

From paper clips great option car stands. To make it, you need to disassemble the large clamp and slightly bend the metal parts, as shown in the photo below.

In order not to damage the surface of the phone metal mounts It is recommended to wrap with threads in several layers. We return the holders to their place, additionally fix them with adhesive tape and clerical gum. We fix the clamp on the ventilation shutters. The phone is securely fastened between the metal parts of the binder.

Plain office paper, folded in a certain way, can even support the weight of a large smartphone. To make a stand out of paper, you need to measure the dimensions of the phone and adjust the pattern below for them.

Cut out the piece from paper, fold it along the dotted lines and insert the side pieces into the slots. This design is good because it allows you to charge your phone without removing it from the stand.

We study popular options for coasters for home comfort

A desktop phone stand for the home should not only be comfortable, but also durable, stylish and fit well into the interior of the home. Consider options for such products.

A phone stand made of newspaper tubes will be a wonderful gift and a great decoration for any interior.

To weave such a stand, you will need several pre-painted long newspaper tubes, scissors, knitting needles, a little glue and varnish.

We place six blanks parallel to each other at a distance of about 1-1.5 cm and firmly fix them in the machine or in any convenient way. We lay knitting needles or wire in the extreme racks to make it more convenient to form even and neat contours of the product. We begin to braid the base with a working tube using the “rope” technique or chintz weaving. We monitor the parallelism of the rows and, if necessary, coat them with glue for better fixation.

Weave a rectangular blank of the required length. We take out the knitting needles or wire. The ends of the stands are neatly trimmed and trimmed. We give the workpiece the necessary curved shape, if necessary, wetting it a little with water.

Similarly, weave the leg of the stand on a smaller number of tubes. We bend the finished leg, install it on the main part and fix its racks between the rows of the stand. Cut off the excess and hide it. We coat the product with glue, if desired, additionally paint and cover with 1-2 layers of varnish. After complete drying, the stand can be used for its intended purpose.

Modular origami is a fairly young, but very popular type of needlework. With it, you can make a lot of unusual and original gizmos, including a phone stand from modules.

To make the stand, you will need double-sided paper in blue and Pink colour. We cut the sheets into blanks and fold the modules.

We start weaving from the base of the stand. For it, you will need 28 blue modules, which must be connected to each other and closed in a ring. We make three more rows in the same way. From the fifth row, we reduce the number of modules by 1, 2, 3, 4 pieces. In the seventh row we put one pink module in the middle.

In the eighth row we put 6 modules, make a pass, another 10 modules, a pass, 6 modules. The number of pink modules is 2 pieces. In the next row, we put three pink modules on the pink section. We begin to make out the curly edging of the stand, as shown in the photo below.

In the back, we form a pattern in the form of a heart, above which we install a number of modules blue color. Gradually narrow the stand until a triangular wedge forms in its back.

Stand of modules is ready!

Video on the topic of the article

We suggest watching the video tutorials below on making other options for phone stands.

It will not be difficult for a home craftsman who has a minimum of tools and a maximum of diligence to make just such a wooden phone stand. As a material, a board 10 mm thick, plywood, is suitable. You can also use thinner plastic. Approximate dimensions shown in the figure. The stand is 10 centimeters high, 8 cm wide (6 cm clean). Installed on two semicircles with a radius of 4 centimeters. Of course, before you get down to business, measure the widest of the phones that will stand in it. A stand is assembled for PVC glue, then decorated at your discretion. For example, in the figure above, the edging is processed by burning.

Well, here I think it’s hardly necessary to explain anything, especially to us - people who are not young. Yes, of course, many have learned, the good old "cassette" from a tape cassette.

Just remove the cassette, turn the cassette holder over, open it to the other side and you get a stand at an angle of about 75 degrees. The width of the "pocket" is about 12 millimeters, the current thin smartphone fits perfectly there.

Here is such a "brutal" stand for the phone from an ordinary aluminum plug. The two extreme teeth are bent at the very base at an angle of 90 degrees. The two middle tendrils are bent at a distance of 15 millimeters from the base, also at an angle of 90 degrees. Your gadget is inserted between them. The fork handle plays the role of a support.

This coaster requires six clothespins and one pencil. The pencil is preferably hexagonal, on a round clothespins will slide. I think it’s clear from the photo - four clothespins are legs, two on the top actually hold the gadget, a phone is inserted between their petals. The width adjustment is very large - the length of the pencil. By the way, even if you hook a couple of clothespins on the edge of any vertical surface (let's say the wall of the box), they will successfully cope without four other clothespins and a pencil!

This stand is very simple, but also suitable for small phones. This is an ordinary old bank or discount plastic card. It should be divided across into three equal parts with a pencil and bent along the lines. But I would make the lower "heel" on which the phone will stand only a centimeter, and divide the remaining distance into the "shoulder" of the prop and support itself.

Modern means of communication perform many functions, so it often becomes necessary to install a gadget on desk. Easiest to buy finished fixture in the nearest store, or you can make it yourself. There are many ways to make a phone stand from improvised materials and stationery.

Similar articles:

The most common material that phone holders are made of is plastic. To make a smartphone holder with your own hands, you can use everything that is available in every home - paper clips and binders (clips), wire hangers for clothes, paper, wooden planks, and even the children's designer. Self-made coasters will be not only comfortable, but also original in their design and size.

There are a few simple ways, thanks to which you can quickly create functional and perfect stands for your gadget.

From stationery binders

Students and office workers are familiar with special clips for large stacks of papers, which are called binders. If you have holders, it is easiest to make a do-it-yourself phone stand from them.

To do this, it is enough to connect 2 elements to each other, and bend 1 metal end towards the phone.

You can also fasten 2 binders with a piece of cardboard, and insert the smartphone into the plane between the metal ears. Despite its small size, such a device is able to hold even a phone with a large screen diagonal both vertically and horizontally.

From the Lego constructor

If children live in the house, there will definitely be a plastic constructor with parts of different sizes and colors. There are no special instructions for making a phone stand, you just need to select the appropriate elements and connect them in any order. The main thing is that the design is stable and attractive.

From a paper clip

Of the many ways to make a shipment for a smartphone, the fastest and easiest is the one that uses a simple, oversized paper clip.

To make a fixture, you must first unbend the clamp into a straight line. Then bend again so that the middle part creates support for rear wall, and the hooked edges prevent the phone from sliding forward.

From a wire hanger

If you have a wire clothes hanger, you can make original stand for smartphone or tablet. To work, you only need pliers and a little patience:

1. First you need to bend both edges of the hanger so that they are located from each other at a distance equal to the width of the gadget. The edges are compressed with pliers until they are completely connected.
2. At each end, 2 folds are made about 3-4 cm in size.
3. In the next step, the hook is bent at an angle of 90° and turned towards the wings.
4. Then, a hook is made at the end of the upper part, for which the inner element of the hanger is hooked and fixed.

The design can be improved with rubber tubes, which will provide an anti-slip effect and make the product more attractive.

Shampoo bottle version

An empty shampoo bottle can be turned into a convenient and beautiful phone holder. The advantage of such a device is that it can be hung on the power supply of the charger and eliminate the risk of hooking the wires and dropping the gadget on the floor.

To make the holder, you will need a plastic container of the required size, a marker and a stationery knife. First, markings are applied to the bottle for future cuts, taking into account the depth of the phone, the location of the holes for the plugs and the dimensions of the power supply. After the layout is carefully drawn, all the lines are cut out with a knife, and the edges are cleaned. If everything is done correctly, the holder can be easily put on the charger plug and plugged into a power outlet. The gadget itself will fit freely in the bowl, excluding the bending of the wires.

To make the device look more attractive, its surface can be pasted over with a cloth or bright paper, painted with paint suitable for plastic. The advantage of such a stand is its cheapness, since the material intended for discarding is used. Also available wide choose colors and container sizes.

Popsicle stick option

Do not rush to throw away popsicle sticks. You can also make a beautiful stand for your phone out of them. Depending on the project, the design consists of several elements or includes a dozen components. Sticks can be glued with PVA or glue gun. After the holder is ready, it is recommended to paint or varnish it.

From paper

One of the most common materials used to make a DIY smartphone stand is paper or cardboard. With proper design, a fairly strong product will turn out.

The easiest way is to create 2 triangular blocks different size. One will serve as a base, the other - a support for the bottom end of the phone. After the blanks are completely dry, they are fixed on 1 paper rectangle.

When there are lovely people in the house cozy little things, it helps to create a warm atmosphere. Making something interesting and useful at the same time is not so difficult. Today, almost everyone has a mobile phone. When we return home, we most often put it on the table. It happens that we do not notice and throw paper or other things on top, and sometimes we completely lose it on the desktop. A do-it-yourself phone stand solves two problems at once: you can always make room for your phone and design it yourself.

How to make a phone stand?

You probably have at least one at home. cardboard box. From such waste material you can create something unique. We suggest making a phone stand out of paper and an old box.

1. For work, you need to prepare stationery glue, a pencil with a ruler, a knife.

2. Before you make a phone stand, you need to prepare the cardboard. We cut rectangles measuring 10x20cm. We need 9 of these blanks.

3. Now you need to glue them three by one.

4. On two we draw such a detail. This will be the sidewall of the do-it-yourself phone stand.

5. Cut out. In order for everything to be beautiful and the structure not to lose its stability, you need to lay the sidewalls one on top of the other and check how much they are the same.

6. We take a clerical knife and cut a hole in the form of a rectangle.

7. Next, you need to make the base for the stand for the phone with your own hands. We measure the width of the phone and cut out the stand from the third blank according to the size. The phone's width is the length of our rectangle. The width of the rectangle should be such that it can fit into the grooves on the sidewalls.

8. We assemble the structure. You will also need a small circle of cardboard, its diameter is slightly smaller than the distance between the sidewalls. (photo 8)

9. All blanks must be pasted over with paper. It can be newspaper clipping or scrapbooking paper.
10. To make the back, take two pencils or something similar. We make holes in the sidewalls and insert them there. On the axis we put our circle of cardboard.
11. Do-it-yourself mobile stand is ready!

Another do-it-yourself phone stand option

You can make a simpler version of such a cardboard stand.