Two three-level stretch ceilings. Two-tier stretch ceilings. LED strip around the perimeter

Stretch ceilings of several tiers have not surprised anyone for a long time. This finish not only looks impressive, but also allows you to hide structural elements or communications. Thanks to the emergence of special profiles for level transitions, make a two-level suspended ceiling easy with your own hands. The manufacturer takes on most of the work. Based on the provided sketch, the material is calculated and cut, as well as the preparation of structural elements. All that remains is to assemble the frame and stretch the fabric. This will result in significant savings in installation costs. We have prepared step-by-step instructions in which we will consider in detail which profile to choose to create two levels, how to properly prepare a drawing for the manufacturer and perform installation.

Types of two-level structures

According to the design, there are three main options for two-tier stretch ceilings. They vary in the materials used and complexity of manufacture.

Regular

The canvas is stretched in two levels, the design is a simple transition without a niche and hidden backlight. PVC film is mainly used. First, a frame of special profiles is installed, then the fabric is stretched over both levels. Often tiers are made from materials that differ in color and texture. Contrast emphasizes the difference.

Combined

In such a ceiling for tiers they use different materials. The second level (closest to the floor) is assembled from plasterboard. To do this, install the frame and sheathe the gypsum board. Then the structure is puttied or painted.

A film or fabric sheet is stretched as the upper level (located closer to the base ceiling). The baguette is attached to the vertical part of the plasterboard structure. To prevent it from coming off under tension, the joint is pre-strengthened. To do this, add an additional aluminum profile or wooden beam, since drywall does not have sufficient strength.

The main disadvantage of this option is that more long term installation For a stretch ceiling, it is enough to install a frame and stretch the film or fabric. And in the case of drywall, you have to additionally finish it and wait for the putty, paint, etc. to dry. This wastes time.

Backlit

The general principle is the same as for the usual two level ceiling. But additional lighting is installed. For this they take special frame, into which the LED strip is then placed. Such baguettes are available for installation both near walls and between levels. The lighting can be located around the entire perimeter, only on one tier or in a niche between them.

Minimum room height for installation

During the installation of any tension structure, the ceiling is lowered. If the room ends up being too low, it will be awkward and uncomfortable to be in.

for living rooms and kitchens in temperate climates - 2.5 m;
in hot or cold areas - 2.7 m;
for corridors and hallways - 2.1 m.

The shortest distance by which the ceiling will drop is determined by the width of the profile. For baguettes of the first level this is 3-4 cm, for the second - 8-10 cm. That is, the height will decrease by at least 11 cm. The calculations are valid for rooms with a small vertical difference in the ceiling.

It turns out that a height of 2.7-2.8 m is sufficient for a two-level stretch ceiling. Hallways and halls may be lower.

Material selection

The fabric used is thin polyvinyl chloride film (PVC) or synthetic polyester fabric impregnated with polyurethane.

From the point of view of two-level structures, the most important differences between the options are:

The film is more elastic, so you can make any shape of levels with it.
PVC fabric has more options colors (about 200) and textures (glossy, matte, satin and various textures). Polyester comes only matte and has only 20 colors.
For fabric and film, baguettes are made with different types fastenings. Special profiles for level transitions are produced only with harpoon fastening for PVC sheeting.

The film is cut out in production exactly to size. A harpoon (a strip of thicker polyvinyl chloride in the form of a hook) is welded to the edges. During installation, the canvas is simply tucked into the baguette using special spatulas. The harpoon is inserted into the groove of the profile, snaps into place and securely fixes the material. Installation is quick and easy, since the blade dimensions and tension are calculated at the factory.

For these reasons, fabric is rarely used in such designs. It is stretched only with combined ones (that is, in combination with drywall). The most common option for a two-level ceiling is a polyvinyl chloride sheet with a harpoon. This makes it easier to choose a baguette and create a complex design.

Selecting a profile for a two-level ceiling

There are several options here too. You can take a separating baguette, which is used to connect the canvases at the same level (marked with the letter combination SP) and a bumper. This is a profile resembling the letter “Y” or “Z” in cross-section.

With this method of installing the second-level frame, the separating baguette is placed not horizontally, but vertically. It is secured to the top of a beam or strong plank. And the bumper is screwed to the bottom. One piece of film is inserted into the upper part of the separating profile and tensioned at the same level. And the other one is tucked into the lower slot and carried vertically to the bumper, where the film changes direction to horizontal.

But this method is relatively difficult to implement. More often they take baguettes specially created for two-tier ceilings. They are divided into several varieties, each with its own marking and purpose:

PP- for easy transition between levels (tier height can be 5, 6.5 or 7.5 cm).
NP- to create a niche with interlevel lighting (the transition height is 5 cm).
KP- used together with the previous profile, performs a load-bearing function (height 9 cm);
PL- to transition the level with backlight, the baguette has a niche for installing an LED strip, which is covered with a light-diffusing insert (height 7.5 cm).

All types of profiles are used to create both straight and curved structures (circles, ovals, waves or spirals). To make the frame bend, the baguette is sawed every 15 mm. And then, for strength, they are fastened with aluminum tape and self-tapping screws (approximately one strip per three cuts or 2-4 cm).

Let us consider in detail the technology for installing a simple two-level stretch ceiling. The material of both tiers will be PVC film. As a frame we use a PP 75 ceiling profile for a stepped level transition. We will install spotlights in the lower tier. This is the most simple design two-level stretch ceiling for self-installation.

Required Tools

For installation you will need:

stepladder (can be replaced with a stable table or stool);
tape measure and pencil;
laser level or hydraulic level;
marking cord (chokline);
hammer drill with a drill with a diameter of 6 mm;
screwdriver or screwdriver;
grinder or hacksaw and file;
gas heat gun(can be rented);
a set of spatulas for filling the film;
sharp knife.

Preparatory work

Before you begin installing a two-level stretch ceiling, you need to take the dimensions of the room, draw a diagram and transfer it to production. Then the base floor is prepared for installation.

Measuring the room and creating a ceiling diagram

It is necessary to accurately determine the length of each wall and calculate the size of all angles. Even in a rectangular room, these dimensions may differ slightly. It is also important to determine where electrical wiring and other communications are located, if any.

Taking this data into account, you need to schematically draw the room and draw a sketch of the future ceiling. It notes:

room dimensions;
which of the tiers will be the top and which will be the bottom;
distance from the border of level 2 to the walls.

The stretch ceiling diagram along with the dimensions is transferred to production. Specialists will create a frame and cut out the film (if the ceiling is wider than the roll, the sections are soldered on a HDTV machine).

Attention! It is better to order everything from one organization. This way the frame and the canvas will fit each other exactly.

Preparing the base base

While waiting for materials, you can start working on the rough ceiling. The remains of the previous finish are removed from it: paint, plaster, wallpaper or tiles. To do this, use a spatula and water, sometimes with the addition of special means. If you do not remove the old coating, it may fall onto the film after installation. Then the ceiling will sag unsightly under the weight, and if the corners are sharp, it will tear. It is easier to prevent such problems than to repair or completely change the canvas later.

The surface is carefully inspected in search of cracks and joints of concrete slabs. They need to be sealed, otherwise in the future the ceiling may inflate or stick to the base when a window or door is opened. Used to seal cracks polyurethane foam, sealant or plaster, which is sometimes placed in several layers. Before applying the next one, wait until the previous one has dried.

Careful leveling of the base is not required, as it will be hidden. But you need to prime the ceiling with an antiseptic. This treatment serves two purposes: it strengthens the surface and prevents mold from developing. This is important, since a humid microclimate is created under the film, favorable for fungus.

Ceiling markings

The drawing must be transferred to the ceiling and walls. First, measure the height in the corners and places of level transition. From the lowest point, set aside the required distance (by which the ceiling will drop). Then the beating cord is pulled between the marks, pulled back a little and released. Thus, using a chokeline, horizontal lines are drawn on all walls.

The second level is marked similarly. The boundary between the tiers is marked on the ceiling. For straight lines, use a marking cord. Curved ones are marked with various devices: templates in the form geometric shapes, a thread fixed at one point with a pencil at the other end, etc. In the case of ready-made structures, simply apply the workpiece to the ceiling.

The locations of the lamps are also noted. Check that the required distances (between them, to the walls or to the level transition) are the same.

Advice! It is better to mark the location of the light bulbs on the floor. Then they will be easier to find after installation.

Frame installation

If the dimensions of the 2-level ceiling structure are too large, it is delivered in separate parts. Then you will have to assemble it on site.

Then the profiles are attached to the walls and ceilings. If you screw the PP 75 baguette directly to the slab, the height will decrease by 9.5 cm. Sometimes more is required, then the frame for a two-level stretch ceiling is installed on metal corners or wooden beams. To maintain a horizontal plane, use a level or a thread stretched between points on the walls.

Then the wall molding is installed. The fastening pitch is 10-15 cm. On loose and fragile partitions, as well as closer to the joints, it is better to reduce it to 5, and sometimes even to 2-3 cm, or strengthen it with spacers.

The fitting of the baguettes is done closely without gaps or level differences. To avoid damaging the blade at the junction during installation, the edges of the profile are processed with a file, and the junction is sealed with aluminum tape.

Installation of embedded lamps and electrical wiring

You will need platforms, flexible steel hangers for fastening and self-tapping screws “bugs” 3.5x9.5 mm. For spotlights they are produced (fixed of different diameters and universal).

Taking into account the distance from the base ceiling to the film, the height of the suspension is determined. The excess is cut off, the plate is bent like an accordion and attached to the platform. This way it will be possible to further adjust the height of the structure, and the strength will not suffer. Holes are drilled in the floor slab, then the mortgages are fixed into them with self-tapping screws.

After this, they begin laying the electrical cable. The lamps are connected to the network in parallel. If one of them burns out, the rest will work.

The wire is pulled to the first platform, a loop is made about 10 cm long, and then to the next, etc. To prevent the cable from touching the suspended ceiling in the future, it is fixed to the hangers. To do this, it is convenient to use small pieces of punched paper tape or plastic clamps.

Important! The wire should not be pulled, there should be a slight sag.

The ends of the loops are cut, stripped and inserted into the terminal blocks. This connection of lamps is safer and more convenient than twisting. To prevent the wires from interfering with installation, they are bent upward and tucked behind the inserts.

To make the film stretch and become more elastic, it is heated with a heat gun. Before starting this stage, close the doors and windows to prevent drafts.

The canvas is carefully unrolled on the floor and then hung to the corners using crocodile clips. The film is heated and gradually tucked into the baguette with a spatula. The sequence is:

first one of the corners;
then the opposite and the rest;
the middle of the walls;
between these points;
and further along the entire perimeter.

This way you get a smooth canvas without wrinkles or folds.

Note! First the lower tier is pulled, and then the upper one.

Installation of spotlights

The marks on the floor determine where the mortgages are located. Thermal rings are glued to the ceiling, which are needed to protect the PVC film from overheating. During operation, the material will not melt when the light is on and will not separate from the cut.

The protector is coated with assembly adhesive (preferably Cosmofen CA-12) over the entire surface to prevent voids from forming. Then the ring is applied to the ceiling and pressed for 2-3 seconds, without moving or smoothing.

When the protection is stuck, the film inside is cut out with a construction knife. Trim the mortgage so that it is level with the ceiling. They pull out the wire, connect the lamp and put it in place. Built-in models have retaining springs on the body that need to be pressed and inserted into the hole in the ceiling.

Masking joints

Due to the design features of the baguette, after installing the tension fabric, gaps remain: between the ceiling and the wall, as well as the upper and lower tiers. To close the gap, use a decorative plug. This is a PVC insert, which is chosen to match the color and texture of the film.

Masking tapes are available in several varieties. Along the perimeter of the room with a harpoon mount, insert:

T-shaped plug - for smooth walls;
SL - wide insert, allows you to hide gaps in curved areas;
L-shaped (corner) - more elastic, suitable for hard to reach places or curved baguettes.

To mask the level transition, other models are used, since the size and shape of the gap in the separating profile is different:

oval (looks most aesthetically pleasing);
"fungus";
tube (round section).

More recently, most owners of apartments or private houses, during the next renovation, carried out a simple ceiling finishing, which consisted of simply whitewashing it or as a last resort, the ceiling was covered with white wallpaper. But this time has already passed, and whitewash has been replaced by a wide variety finishing materials. Stretch ceilings are considered one of the types of ceiling finishing. Their history is quite long, since they were used even under Emperor Neuron.

Today, multi-level stretch ceilings are one of the most modern materials high strength. They can also be given any shape. If necessary, any designs can be created on them.

One of the types of stretch ceilings is 2-level stretch ceilings. Today they are considered the pinnacle of evolution in the field of finishing ceiling coverings.

To get started, you need to prepare the tool that will be used:

glazing nails;
perforator;
hammer;
screws with dowels;
roulette;
screwdriver;
graph paper;
pencil with eraser;
nylon thread;
drywall;
wooden blocks.

It is much simpler to perform than multi-level, but no matter what, it is still possible. This will take more time, materials and effort.

Stretching 2-level suspended ceilings should be done last, only after the major renovation of the room has been completed. Therefore, during repairs, all furniture and other items are removed so that they are not damaged by the impact. high temperature. Since during the heating of the film, the temperature in the room will reach 65-70°C.

Any can perform room zoning functions. For example, in this way you can separate the dining room from the kitchen.

All steps for installing a suspended ceiling must be carried out step by step in strict sequence:

First you need to measure the height of all corners in the room. The lowest angle is located. Then you need to retreat 5 cm from it by driving a bead nail into this place. After this, you need to measure the same distance along all three remaining corners. A nylon thread is pulled through the corners. Thanks to this action, alignment is made around the perimeter of the entire room. Now you can easily calculate the working perimeter.
After calculating the perimeter, a sketch of the future ceiling is drawn up. For convenience, you can take a double squared sheet of paper or graph paper from your notebook to recreate the most accurate space and extremely accurate final measurements.
Buy 2-level stretch ceilings You can order them from companies that specialize in them or purchase them in stores. There are two types of base layer: . The owner of the future ceiling must decide which type to choose. Using both types allows you to create a visual distinction that will have a positive effect on the overall appearance. Typically, most customers choose one of forty shades of white, and much less often use other shades and colors.
The main part of the work begins after the ceilings are brought into the room. First you need to step back 5 or 6 cm from the level of the stretched thread, then exactly the same thread is pulled in parallel. In the event that the second level of the stretch ceiling does not touch any wall, this is not a problem; you don’t have to run the thread along it.
The outline of the second level must be marked with a marker or chalk along the ceiling. After the outline is ready, wooden blocks of a height specified in the sketch (usually 10 cm) begin to be screwed onto it. If there is a difference in height, then there is a slight spread. If the plan is to create a rounded corner, then in this case drywall is used, because it can be given any shape quite easily. It also needs to be mounted on bars.
On almost all 2-level stretch ceilings it is necessary to install two types of illuminators. The first type of lighting is, and the second type is spot lighting, which should be displayed on the second level. It should not exceed 50 watts.

Stages of main work

For basic work you will need the following tools and materials:

perforator;
profile;
screwdriver;
thermal gun;
screws with dowels;
PVC matte;
PVC glossy;
spatula with a rubber tip;
harpoon mount;
decorative plinth.

Work process

A two-level suspended ceiling with lighting is understood as a hanging system for decorative purposes. It consists of profiles made of metal or plastic, decorated with elastic fabric.

Purpose

Two-level stretch ceilings have enormous potential for creating a unique atmosphere in the finished room. With their help, you can implement numerous design ideas. Modern systems This type may generally contain fabric or PVC film. For reliable fixation of the material, it is provided frame construction, consisting of a durable aluminum or plastic profile.

Thanks to the two-level ceiling, it is convenient to achieve the effect of expanding space when zoning rooms. By using satin and glossy fabrics, your home can be made lighter and more comfortable. Despite their versatility, two-level stretch ceilings are used most often in the hall.

Installation work

Installing a two-level structure will require some experience in construction work.

Preparation

The advantage of any hanging ceiling system– the ability to hide irregularities and flaws in the rough foundation. Unlike painting or wallpapering, in this case there will be no need for careful leveling of the concrete floor.

Preparatory activities are carried out as follows:

Freeing the room from unnecessary things. Any ceiling decoration requires free access to its entire area. Perfect option– completely remove all furniture from the room. Objects that are too bulky to remove can be moved to the center by covering them with waterproof film. Also, chandeliers, lamps, cornices and all other elements need to be removed from the ceiling surface.
Cleaning the base. If as old decoration whitewash or paint has been used, it is advisable to remove it. The fact is that further shedding of small particles can damage the tension fabric. Ideally, you need to clean everything before concrete slab. This procedure is carried out with a durable scraper.
Sealing joints. In some houses, the ceiling does not consist of one solid slab, but several. The connecting sections between them begin to crumble over time. The same goes for corners. All these areas must be sealed with a new solution, after removing the old one. It is most convenient to use a starting putty such as Rotband or Isogypsum as a mixture. The tools you will need here are a set of spatulas and a plastic mixing container.
Applying primer. The impregnation used forms a moisture-proof layer on the ceiling, which subsequently prevents the development of fungus and mold. Deep penetration acrylic primers have proven themselves to be excellent in this regard: the liquid is poured into a plastic bucket and applied with a brush or roller. If there are already traces of mold on the ceiling, additional treatment of the affected areas with a special antiseptic is carried out.
Laying communications. It should be taken into account that upon completion of the installation of the two-level stretch ceiling structure, access to the rough base will be closed. Therefore, all necessary electrical work on laying wires and cables must be carried out at the preparation stage.

During this procedure, a lot of dirt and dust usually arises, so it is advisable to further protect the walls, floor and windows plastic film. You should also ensure that you have work clothing and breathing protection.

Development of an installation diagram

During the preparatory activities, a diagram of a two-level stretch ceiling is drawn up. The main task is to determine the installation points of the lamps.

Considering the specifics of the system, it is best to use two levels of backlighting:

Main. Includes traditional chandelier and light fixtures.
Local (hidden). Organized using LED strips and built-in spotlights.

System arrangement

Installation activities may only begin after the primer and sealed areas have completely dried. To speed up the drying procedure, it is recommended to use ventilation. The humidity level in the room should not exceed 75%, with an average air temperature of +24 degrees. It is this microclimate that most contributes to the correct straightening of the stretched fabric, preventing its shrinkage. While the room is drying, you can start developing a sketch of a two-level ceiling, with a clear indication of the configuration of each level and the location of the main lighting.

The finished drawing of a stretch ceiling in two levels is transferred from paper to the base. To apply curved lines, it is best to use a plastic profile. This structural part can be easily bent, without damage to smooth transitions. Having completed the process of creating a drawing for setting levels, you need to decide on the height of the lower level of the stretch ceiling. Optimal indicator– at least 15 cm.

If there are unevenness and differences on the floor, it is most convenient to use laser level. With its help, each of the walls is marked with marks for the attachment points of the profile, over which an elastic fabric or film will be stretched. The areas where lamps and chandeliers are located are equipped with wooden pads, allowing you to adjust the level. Finishing installation work At these points, using a soldering iron, holes are made for the lamps. To install them, special brackets are used, and to close the holes - decorative inserts.

Plastic frame

Installation of a frame for a two-level stretch ceiling includes several stages:

Fixing wooden blocks on which the future profile will be attached. Dowels are used as fastening elements. Strictly speaking, we are talking about a simplified version of the frame. There is a possibility of using metal U- and C-shaped profiles to create it, but in this case you will need some experience working with such elements. Beginners are recommended to choose wooden blocks, when installing which a step of 20-30 cm is used.
Installation of plastic profile. The previously applied markings serve as a guide. For fixing to wooden blocks, ordinary wood screws are used. Connection of profile ends The system includes special plastic adapters, which are also fixed to the pads. To close the plastic profile from below, use a corner flexible perforated insert. She is being fixed polyurethane glue. Thanks to this, the lower plane of the system is free of sharp protrusions, which often cause tears in the elastic fabric.
When installing a two-level stretch ceiling structure, you should in every possible way avoid any damage to communication lines or fire alarm. Cable channels are used to protect the wiring. There is also an option for fixing the wiring to the ceiling using special brackets. The sections of the frame that come into contact with the cable are equipped with small cutouts.
The task of the plastic profile is to determine the height of the lower level of the system. Its fixation should be as reliable as possible (the normal point load is at least 15 kg). Such a safety margin can even withstand flooding from above, which sometimes happens in multi-story buildings.
In areas of contact between the plastic and the wall, the corner parts of the profile must be cut off. For this, a grinder with an emery sheet or a regular file is most often used. This ensures a smooth slope towards the wall. It is very important to achieve a smooth contact point: rough transitions must be avoided. The contact point is equipped metal profile with a harpoon - this line will also be decorated with a tension fabric.

Metallic profile

Upon completion of the installation of the plastic elements, they move on to the metal profile. The place of its fixation is the perimeter of the walls at a previously specified height. A laser level is used for this. You only need to use the profile that is included with the stretch ceiling. This element is specific in that there is an elastic pressing insert inside it (in other words, a harpoon). Thanks to the insert, the edges of the fabric stretched over the frame are secured. Dowels are used to fix the profile to the wall.

Equipped with another metal profile plastic element on the side where there are no bars. After this, all prominent fastener heads are masked using light-colored masking tape. If this is not done, they will be visible against the background of a white two-level stretch ceiling. This is especially true for bright sunny days, or when all the lamps are on.

Selecting a canvas

The design of two-level stretch ceilings suggests the possibility of using two types of fabric:

PVC film. A durable material characterized by elasticity, moisture resistance and low cost. In case of contamination, the film can be washed with a sponge and soapy water.
Polyester fabric. Inferior to film in terms of moisture resistance, surpassing it in decorativeness. No heating is required during installation (unlike PVC). The fabric is breathable, so the effect confined space does not arise. It is mainly used in two-tier stretch ceilings in the hall.

Two-level systems can be equipped with several materials at once. It often happens that a glossy PVC film is used to furnish the first level, thereby achieving a visual expansion of the space. The 2nd level stretch ceiling can be decorated with textured satin-like fabric. This combination looks very beautiful, which explains its popularity when implementing design ideas.

The final choice of material for the canvas depends on the taste of the customer. In specialized stores you have the opportunity to independently evaluate the parameters of materials, deciding on shades and texture. It is possible to order photographic film based on an individual design. Depending on the complexity and quality, the cost of production is determined.

As for the combination of a two-level stretch ceiling and a plasterboard base, this solution is not very practical. The exception is the forced zoning of premises of a large area. In this case, the rigid base must be equipped with an aluminum frame made of C-shaped profiles.

Installation of tension material

First of all, the lower level of the structure is arranged, and then the upper one. Let's figure out how to stretch a stretch ceiling and what the sequence of actions is.

Installation procedure for a 2-level stretch ceiling:

The straightening of the PVC sheet is accompanied by blowing with a gas heat gun. When using polyester fabric, this procedure is not necessary.
The straightened canvas must be fixed at a height of 1.5-2 meters with special rubber clothespins. To achieve complete removal of all folds, the film is blown from below again gas gun. Despite the increase in air temperature in the room, opening windows is prohibited.
The tightening procedure must begin from the plastic profile, from the corner section. In this case, you will need a plastic spatula as a tool. The edges of the material are put on the protrusions, pushing into the harpoon. Reliable fixation of the canvas is ensured by special inserts. Proceed in a similar manner in each of the corners. This is followed by another blowing with a heat gun.
After waiting for the film to cool, it is attached along the perimeter of the two-level stretch ceiling. It is important to achieve uniform tension, otherwise ties will appear. Areas for fixing the canvas to plastic profile are decorated with reinforced tape: in these places, a profile for the upper level of the stretch ceiling is attached to self-tapping screws.
The installation of the second panel is completely identical.

Two-level ceiling lighting

To determine the points of the holes for the lamps, press the canvas with your hand, feeling for bars or plastic rings. Cutting is not suitable in this case: burning is necessary. To do this, you can use heated rounded reinforcement. The main thing is to achieve melting of the edges, otherwise the film will tear. Cutting can only be used in combination with a special plastic thermal ring glued to the site of the future hole. To cut a hole along the inner contour of the ring, there are usually no problems.

After this, you can begin fixing the lamps using hangers. Decorative inserts are used to disguise attachment points. If necessary, power supplies and circuit breakers are attached to the floor slab. During the implementation of this procedure, the voltage on the electrical panel is turned off. There is an option for illuminating a stretch ceiling using LED strips installed behind ceiling cornice. Such lighting allows the use of color changes and a remote control unit.

How to make beautiful two-level stretch ceilings? Photo for the hall, useful tips, all this can be found on the website of any major design agency. If earlier such ceiling structures were considered a manifestation of luxury, now they have become commonplace and commonplace.

Features of two-level structures

Two-level stretch ceilings for the hall require serious preparatory work. It is important to first create design project, which will take into account all the features of this premises, the dimensions of each level are thought out, what materials will be used to bring the plans to life, and only after that begin practical work.

The living room is the place in a house or apartment where not only family members, but also numerous guests gather. The appearance of a given room determines the impression that friends will make about the owner of the room, his taste and material well-being.

Advice! Two-level suspended ceilings in the living room should be chosen if the room is of sufficient size.

Selection of material for decoration

Drywall is of particular interest as the main material used to decorate the ceiling surface. With its help, you can create two-level tensile structures for the living room, characterized by an aesthetic appearance and maximum functionality.

At making the right choice shape and configuration, you can count on the fact that the created two-level ceiling will become a decoration of the living room, an excellent addition to the overall image chosen for the living room.

Drywall has excellent technical and operational characteristics, has an acceptable cost, and therefore is considered the optimal material for organizing two-level suspended ceilings in the living room.

Main mistakes when creating two-level structures

The ceiling should be integral part general design, chosen for the living room, and not as a separate element.

Attention! IN small room a two-level multi-color ceiling is inappropriate.

The main purpose of a two-level ceiling structure is to divide the space in the room into separate zones.

For example, if the plans include separating a seating area and a dining area in the hall, it is quite possible to arrange a two-level glossy or matte structure made of plasterboard sheets.

Advice! The first level of the created masterpiece can be used in the sofa area, and the second level can be placed in the dining area of the living room.

If the hall is of modest size, then it is better to use a single-level matte ceiling, and use walls and furniture for zoning.

So, in the spacious living room, a two-level ceiling allows for zoning of the room. Inside such a canvas you can place the main engineering Communication, and also easily install spotlights there.

In a small apartment, a two-level ceiling option will be absolutely inappropriate, as it will make the space in the room visually even smaller.

Advice! When thinking about the shape of a two-level structure, Special attention it is necessary to pay attention to the organization of additional lighting at each level.

In addition to additional interior lighting, it is also important to pay attention to the selection color option ceiling. When thinking over the color option for a two-level ceiling, it is necessary that the shade matches the overall interior of the living room.

The option of a colored two-level ceiling is appropriate only if it prevails White color. Ceilings having unusual shape, have an original appearance.

A “floating” ceiling requires sufficient free space in the room. That is why professionals advise choosing such complex ceiling structures only if they will be supported and complemented by the layout of the room.

Design Features

Stretch two-level ceilings in the living room consist of two panels that are mounted separately. They are placed at different levels and together represent a complete composition.

Stretch ceilings have significant differences from plasterboard structures. First of all, it is necessary to note the variety of textures and tones of fabric and film materials. The tension version is convenient because in the event of flooding, you can carefully drain the water at any time and return the film to its original state.

Installation of a stretch ceiling can be completed in a few hours, but creating a two-level plasterboard ceiling will require a much longer period of time.

Advice! In order to make a beautiful and unique plasterboard ceiling in the living room, you will need the help of a professional.

The created structure will have considerable height, suitable for a spacious room. With the help of a finished structure, you can visually increase the height of the ceiling, add individuality and additional charm to the living room.

Design specifics

Even with an ugly and uneven base, you can get a smooth and beautiful ceiling surface. The two-level ceiling option has a significant service life, excellent aesthetic appearance, high environmental friendliness, and ease of operation.

You can easily hide all engineering communications inside the created interior masterpiece.

Modern plasterboard ceiling with correct selection will become one of decorative elements interior, living room decoration.

The crucial point is the selection of the color of the ceiling. Dark ceilings are very rare, because they reduce the height of the room. Colored options are preferred by creative property owners who are ready for bold creative experiments.

When choosing the same tones of the ceiling and walls, or with a lighter version of the ceiling, you can count on a visual expansion of the space in the room.

Interior professionals recommend glossy coatings for dark rooms. In a living room filled with an excess of natural sunlight, glossy ceilings not recommended to use.

Warm and bright colors are suitable for those living rooms that do not receive enough sunlight.

Grey, green color you can choose to decorate the ceiling in a hall located on the south side.

Advice! To obtain the most beautiful and harmonious image, you can design the first level in light colors, and make the second one rich and bright.

Thanks to such a roll call of colors, you can get the desired result and enjoy the exclusive option of a two-tier ceiling.
In order to give the ceiling structure a complete look, install lighting using LED lamps or fiber optics.

Thanks to the two-tier design, you can focus on individual details, for example, highlight a seating area, highlight the fireplace corner.

Conclusion

When choosing a plasterboard two-tier structure, you need to pay attention to the features of the overall design of the room. For example, for modernism you can create a ceiling with smooth and streamlined lines. Classic interior assumes smooth and clear lines, so you can limit yourself to single-level ceilings. Lovers of romanticism can choose two-level options in the form of a heart, cloud, or flower.

Designer lighting involves a lighting option that creates a unique atmosphere in a room. Using LED strips and lamps, you can get soft and even lighting, which will visually increase the depth of the ceiling surface and create the effect of a structure floating in the air.

When combining LED strips with different power and color, you can give the surface uniqueness and originality. In addition to the main lighting, you can additionally select floor lamps as lighting.

The plasterboard version can be used for ten to fifteen years without any problems or repairs.

Polyvinyl chloride canvas is a fairly pliable and not difficult to process material that allows you to create varied and stylish, original designs for ceiling decoration. The harmony of functionality and aesthetics in the design of any residential or utility room in an apartment or private house ensures the creation of an exclusive interior and compositional solution.

Simple in their geometry and fairly easy to install, provided you have sufficient experience working with suspended structures, single-level ceilings inferior to two-level ones, which are characterized by a magnificent appearance.

The photos of two-level suspended ceilings presented on the page help you choose for your home the best option ceiling design and in accordance with modern design projects.

Features of canvases for two-level stretch ceilings

Magnificent two-level ceilings illuminated by various lighting sources using energy-saving lamps provide a combination of aesthetic and functional decoration characteristics.

Depending on the texture of the polyvinyl chloride ceiling, two-level ceilings are divided into several types, the appearance of which changes the overall style of the room:

dull mat. Matte, muted colors and special texture allow you to create unique designs on two levels for stylish design ceiling;
structural satin. It has a texture that is not as grown as matte canvas and is used for medium-sized rooms or bathrooms with bathtubs;
bright gloss. Shiny and sparkling varnish looks great in living rooms and common rooms, perfectly reflects the light of natural and artificial light sources.

The suspended ceiling structure is a profile frame on which a PVC film of various types is firmly fixed. color solutions and textures, by heating and stretching to the required length and width.

After installation work, the surface of the canvas is a perfectly flat and smooth surface, even when soldering several films for a color combination, there are no traces of seams or edges.

Design solutions in the design of two-level ceilings

Exclusive and unusual design two-level ceilings, choice suitable options, depends on architectural features the entire home, the general design concept of rooms or designated areas in them.

PVC canvas is perfectly combined with plasterboard structures, which make it possible to realize any, even the most unusual design solution, to the benefits suspended ceilings relate:

smooth and smooth surface. Installation does not require the use of technologies for leveling the ceiling surface; the canvas is stretched by heating, which ensures ideal smoothness;
aesthetic appeal. A rich variety of colors and shades, textured texture and photo printing on ceiling canvases makes it possible to create any composition and pattern;
increased protective parameters. PVC film, when the apartment is flooded from above, does not allow liquid to pass through, which can damage the design of the walls and floor and render the furniture unusable.

Simple care of such structures makes it possible to maintain them in normal condition without making a lot of effort during general, seasonal or periodic cleaning of living rooms and the entire apartment.

Individual sketch of a two-level ceiling

Two-level structures are a functional combination of a frame created from a reliable profile, plasterboard inserts and stretched PVC sheets, and decorate any room.

Beautiful and stylish multi-level ceilings in the interior this is an opportunity to create a play of colors and various geometric shapes, decorating in an unusual and bright way living room, hallway or bedroom.

Preliminary creation of a sketch helps to imagine what the entire room will look like and to highlight individual areas with spectacular accents. functional areas, emphasizing their purpose.

Using two-level suspension systems, you can hide uneven ceilings and improve the lighting in the room by distributing efficient and energy-saving light sources throughout the entire area.

Installation of a two-level ceiling

When thinking about how to make a two-level ceiling, you should understand that this can only be done by qualified specialists who have specialized equipment at their disposal.

A high-performance heat gun is used to gloss and smooth the surface, and a professional hair dryer is used to eliminate small creases on the canvas.

Homeowners cannot participate in the installation of the ceiling structure, but they have the opportunity to interact with the designer who is developing a sketch of the interior solution.

Independently draw up a future concept for decorating the ceiling with a suspended structure and come up with a two-level composition that will correspond to the overall design style of a room or a separate area.

What are the advantages of a two-level stretch ceiling?

In addition to decorating the room, the designs of two-level ceilings help to practically divide the area of the room, to highlight separate areas for family vacation or independent work.

With the help of hanging systems, you can efficiently disguise any engineering and communication wires and cables, highlight interior solution and ensure normal lighting levels.

Supporting the general concept of room design, stretched canvas, depending on the chosen color and texture, perfectly focuses attention on the theme of decoration.