Drilling water wells with your own hands. Drilling wells by hand: hydrodrilling, how to drill with a garden auger. How to drill a water well yourself

Providing a site with water is the first task of its owner. The more ambitious the plans for improving your territory, the more acutely the lack of water supply will be felt. Water is needed to perform construction work, for the garden you are planning to create, and for your own daily needs. If you drill a water well with your own hands, your dream of water supply will not only come true, but will also allow you to save significantly.

There are several real ways get life-giving moisture, which we will tell you about. There are several technologies that can be used to independently extract water in a suburban area.

Choose suitable option you will have to do it yourself, since it depends on the terrain of the area, as well as the technical equipment, finances and skills that you possess. Let's look at the main well structures.

It is difficult to give preference to any one design: each has its own advantages and disadvantages, so the choice depends on the landscape of the area and the capabilities of the owner of the site

The most common well

If there is a spring on your site, then setting up a well is great option water extraction. The shaft of this structure will act as a liquid storage tank. If the source is active enough, up to 2 cubic meters of water will always be at your disposal.

Abyssinian tube well

In fact, this is also a well, but narrow and long. Due to the fact that its length can be approximately 8-12 meters, no pollution from the soil surface gets into the water that fills it.

The Abyssinian well is often called a needle well, because the pipe driven into the ground when creating this structure really resembles a needle

Sand well (filter)

The deepening of this structure to 15-30 meters is carried out by any method: auger, shock-rope, core. The walls of the well are formed using a pipe with an average diameter of 100 - 180 mm. The buried end of the wellbore is equipped with a filter. A mesh of of stainless steel, which is welded or soldered to the first link of the pipe string before immersing it in coarse sand mixed with pebbles.

So you can schematically imagine the design of a well “on sand”, where number 1 is the casing pipe, number 2 is the statistical water level, and number 3 is the mesh filter

This design can satisfy the water requirement of a small country house with two water points. If the operation of the structure is seasonal, it will last about five years. With constant use, you can count on 15 years of water supply.

When the well does silt up, you can try to wash it out. If resuscitation measures do not give the desired effect, a new shaft will have to be drilled. Place it next to the previous one.

Artesian well without filter

This structure does not require a filter. Such a well can reach a depth of 100 meters or more. The water produced using such a structure is contained in limestone cracks. The liquid accumulated in them due to condensation can be not only crystal clear, but also mineralized. Light mineralization is acceptable for everyday use. If the extracted water is classified as mineral water in its composition, then it cannot be used for domestic purposes.

Diagram of an artesian well: 1 - conductor, 2 - statistical water level, 3 - intermediate column, 4 - production column with perforation

It is difficult to determine in advance the depth of the well that will have to be drilled in search of water. You can only roughly get your bearings by talking with neighbors on the site and finding out from them what parameters similar structures have on their territories. The soil layers are uneven, so the information obtained still cannot be considered accurate for your area. For this reason, casing pipes are purchased taking into account the correction of the obtained data.

How is the well constructed?

If you do not focus on the nuances, the essence of installing a water well for a country house is the same: it is a long narrow hole that reaches the location of the water. The walls of the mine are reinforced with casing pipes. Wells differ from each other in width, depth and additional devices that increase their productivity and reliability.

In addition to casing, wells are equipped with equipment for forced lifting of liquid and its distribution. To choose the right pumping equipment and storage tank, you need to know the characteristics of the well, the most important of which is its depth and flow rate.

The flow rate of a well is an indicator of its productivity: the maximum volume of liquid obtained per unit of time. It is calculated in cubic meters or liters per hour or day.

Image gallery

Functions of casing pipes

Casing pipes are the main element of the well. The casing is carried out using separate sections, soldered, welded or screwed together. Special attention they should be given equal diameter: the entire structure should create a straight, even column. If the casing pipes have external threads, the links are connected with couplings, due to which the diameter of the penetration increases.

Casing pipes are needed to:

• When drilling the well, the shaft did not collapse;
• the barrel did not become clogged during its operation;
• the upper aquifers did not penetrate into the structure.

Casing pipes made of steel alloys and polymers (PVC, uPVC, HDPE) are widely used. Cast iron and obsolete asbestos-cement products are used less frequently. The space between the pipe and the soil is filled with concrete if the excavation was drilled in loose soils or the aquifer lies at a considerable depth.

Only after this work is completed, all other equipment is installed. Sometimes during the operation of a well, a slight “squeezing” of the pipe to the surface may occur. This natural process, which does not require any additional measures.

The most popular are metal and plastic casing pipes with threads. The photo shows the installation of a blue plastic casing pipe

Pipe with filter

A pipe with a filter is lowered into the borehole of a double-casing well. Through its perforated first link, filtered water will flow into the head and then be extracted by a pump to the surface. After the pipe is installed to the desired depth, it is advisable to secure its mouth. For this purpose, a clamp is used to prevent spontaneous subsidence of the pipe.

Image gallery

Well head

The upper part of the casing pipe is equipped with a head. The basic design of this device is the same for any type of head. It consists of a flange, a cover and a rubber ring. Different types of heads differ from each other in the type of material from which they are made and additional options.

The heads are made from cast iron and plastic. This is a sealed device. It is used to secure the pump cable and water pipe outlet.

Due to low pressure created with the help of a pipe head, the water inflow increases and, as a result, the well flow rate.

Caisson, adapter, packer

To high humidity did not affect the operation of the instruments associated with the well; a special tank is provided for them - a caisson. It is made of either metal or plastic. Metal caissons, unlike plastic ones, can be repaired; they are better adapted to climates with significant temperature changes. In addition, a metal product can be assembled independently from parts that are sold separately. But plastic models cheaper and they don't rust.

To tightly connect the ground water supply and the well, you will need an adapter. This device is usually placed in the place where all the equipment that needs protection from water is collected. Most often this is a technical room. One part of the adapter is attached to the casing, and the hose from the pump is screwed to the other part.

A metal caisson is an expensive thing: its price reaches 40 thousand rubles, so you can buy it in parts and assemble it yourself, which will reduce the cost of the purchase

Sometimes there is a need to allocate a local section of a deep artesian well, on which, for example, they will carry out renovation work. For this purpose, packers are used - seals for wells.

The listed elements are part of the well design, having a great influence on its functionality.

Four types of drilling

You can drill a water well with your own hands different ways. Let's look at the most popular types of drilling:

• screw;
• rotary;
• core;
• shock-rope.

All types of drilling are performed both manually and using mechanized means. These technologies differ from each other in the methods of rock destruction during the construction of a well and in the methods of extracting soil from the shaft of a structure to the surface. For implementation various methods equipment used different types, which has a significant impact on the cost and quality of the finished structure.

Manual drilling is the most labor-intensive process

For manual drilling carried out using auger, shock-rope or combined technology, will be needed following mechanisms and materials:

• winch;
• drilling rig;
• rods;
• casing.

If the well to be constructed is deep enough, a drilling derrick will be needed. With the help of this design, the drill with rods is immersed and then raised. If the well is shallow, you can do without a tower. In this case, work with the drill is performed manually.

The function of drill rods can be performed by narrow pipes that are connected to each other using threads or special keys. During the process of assembling the structure, the drill must be attached to the lowest rod.

Drilling tools for manual drilling: a, b - spoon drills; V - auger drill; d-d - drill bits; e - bailer

The integrity of the soil is disrupted by the cutting attachments of the drill. They are made of durable three-millimeter steel. The edges of the nozzles must be sharpened, taking into account the fact that the drill will rotate clockwise and destroy soil as a result of the rotational-translational motion.

First, we choose a place to drill. We make a hole in the soil about two bayonets deep. This is how a guide for the drill is dug out. You need to install a tower above the drill entry point we have designated. The height of the tower should correspond to the length of the drill rod: it should be slightly higher than this length. Only in this case can the rod be easily and simply pulled out after finishing the work.

Getting started won't seem difficult. The first turns of the drill penetrate the soil quite easily. One worker can handle this task. But with further immersion into the ground, with each turn the drill moves harder and slower. At this stage of work it is no longer possible to do without an assistant. If it becomes difficult to lift the drill to the surface, you should turn it counterclockwise and then try again.

Manual drilling of water wells as an industrial method was used relatively recently. And now it is possible in those places where it is difficult to deliver drilling equipment

When subsequent penetration of the drill encounters significant resistance, there may be a risk of equipment failure. Therefore, you need to try to soften the soil using water for this purpose.

The work is going on, the drill is moving down, but do not forget that every half a meter of its advance it is necessary to free the tool from the ground, and for this it should be raised to the surface. When the tool is completely immersed in the soil up to the handle, it needs to be extended with the next rod.

The entire drilling process takes a long time, most which has to be spent on lifting the drill to the surface and clearing it of soil. Therefore, it is worth using each cycle as efficiently as possible, trying to extract as much soil as possible.

When drilling a well manually, only the first time you can do the work yourself, then you will definitely need an assistant

If the layers that the tool passes through are characterized by increased flowability, then there is a danger of the well shaft collapsing at the most inopportune moment. To prevent this from happening, you should use casing pipes that will prevent the mine walls from collapsing.

But the condition of the land that comes to the surface has changed: the drill has reached the aquifer. There is very little left. Behind aquifer must be waterproof. The drill must be immersed to the waterproof layer so that water can flow into the well. maximum amount water. The maximum depth that can be achieved by manual drilling is from 10 to 20 meters. It is at this depth, most often, that the first aquifer is located.

First to rise to the surface dirty water, which is pumped out manually or submersible pump. To flush the well, it is enough to remove just a few buckets of dirt. If pure water Don’t rush to change the dirty one, you should drill another meter or two.

Budget auger drilling

It is believed that auger drilling, and not rotary drilling, is the simplest and most affordable option for constructing a well under water. It is the use of the auger method that is incorporated in most modern small-sized drilling rigs.

Auger drilling can be carried out using such a mobile unit, which can be easily transported to the place of its operation

The auger is the well-known Archimedes screw. Those who have ever seen how fishermen drill a hole for ice fishing can imagine what we are talking about. A shallow well, up to 10 meters, is created in a similar way. During the work, neither drilling fluid nor water is used, which is used to wash the tool in other cases.

If you turn to a specialized organization for help, then most likely they will use auger drilling equipment in their work, which is easily transported and widely used.

The peculiarity of this type of work is that it cannot be performed on all types of soil. Using an auger you cannot go through rocks or quicksand, but on dry and soft sedimentary rocks this method has proven itself to be excellent. When performing this work, attention should be paid to protecting the mine from contaminated water from the soil surface.

Image gallery

Rotary method for rocks

If the excavation is to be constructed in rocky soils, then a rotary drilling method is used to create it. It is based on the use of a special drill pipe, which resembles a thin glass turned upside down with a roller bit crushing soil along the lower edge.

Communications used in drilling pass through the pipe cavity. The hydraulic installation creates a load on the bit, which makes its way through the rock. The load is supplemented by the mass of the pipe string.

During rotary drilling, the rock is broken up with a bit like this, which can overcome even significant obstacles in its path.

The soil from the well is washed out using drilling fluid fed into the pipe using one of two possible methods.

• Direct flush. The solution is pumped into the pipe using a pump, after which it flows out through the annulus along with the rock.
• Backwash. The solution enters the pipe by gravity, and is pumped out of the annulus along with the rock by pump.

It is believed that reverse flushing is more effective than direct flushing: with its help, a higher well flow rate is achieved due to the highest quality opening of the aquifer. But to implement this washing method, it is necessary to use expensive equipment, which affects the increase in the cost of work. Direct flushing will cost less than reverse flushing.

Expensive shock-rope method

If you want to get a well that will last you up to 50 years, and you have a sufficient supply of time, effort and nerves to implement your plan, then choose the percussion-rope drilling method. It will take a long time to work. You will slowly but surely make your way to your cherished goal.

This impact-rope structure consists of a frame, a bailer and an impact chuck, which is made of a thick-walled pipe and is responsible for the drilling process itself

The process is based on the use of a specific projectile - a bailer. This is a section of thick-walled pipe 1 to 2 m long with a ball or reed valve at the bottom. A “window” is cut out in the upper part of the pipe for extracting soil, and the top is equipped with an eye for the torso.

Tied to a cable thrown over a block, the bailer is freely thrown onto the face. Falling down, it loosens the soil and captures it with the valve. The process is repeated several times before removing the bailer from the barrel. The bailer removed from the well is freed from the soil: it is turned over and shaken out through the hole.

This method of breaking through a shaft is considered very labor-intensive, but effective. Besides saturated with water Sands and loose sedimentary rocks can only be extracted from the well using the shock-rope method. When gelatinizing, no drilling fluid is used, so the groundwater that appears in the well cannot be confused with it.

Due to its high labor intensity, this method is more expensive than the rotary method. In addition, if the goal is to go beyond the first aquifer, there will be costs to isolate the mine from the aquifers that are located above. For this purpose, additional casing pipes are used. In addition to the increase in material consumption, the volume of work performed by specialists is also growing. Therefore, such a structure will not be cheap.

Video example of manual well drilling

Like any other job, manual drilling can be upgraded using a hydraulic pump and an electric drill. You can do this kind of work even without assistants. The entire drilling process can be seen in this video.

Each type of water well has its own advantages and disadvantages. Now that you have an idea of ​​the type of wells, their design and construction methods, it will be easier for you to make a choice in favor of one design or another, based on the characteristics of your site and your own financial capabilities.

Private property is not only about abundance clean air and silence, but also the need to create individual communications for decent living in the house. One of the most in demand is water supply. For these purposes, a do-it-yourself water well (but not an artesian one) is widely used today.

A source found in soil layers can last from 5 to 100 years, depending on the depth of its occurrence and the total flow rate of the well (an artesian source has the maximum service life). Therefore, let’s look at how to drill a well with your own hands on the site. Moreover, we will reveal to you several methods of independent drilling.

Important: independent drilling is only possible with sand wells. Artesian springs on the site require complex technical equipment and paperwork. You can't do this with your own hands.

Screw method

If you are wondering how to drill a well with your own hands on a site and at the same time want to equip a well for sand, then this method of developing soil is the simplest. To carry out the work you will need:

• Auger with extension pipe;
• Casing pipes for the entire length of the well;
• Strainer;
• Pump (surface or submersible, depending on the flow rate of the well and your water needs).

First of all, you should decide on the location for the well. It is very important to take into account the lowest point of the well location on the site. It is here that, according to the laws of geodesy, underground water accumulates. It is also important to take into account the depth of the aquifer. Ask your neighbors about this. After all, if the layer of water is located lower than 20 meters, then you cannot cope with it with your own hands.

Before making a well, take into account the location of unwanted objects relative to the future source. Neighborhood septic tanks are dangerous industrial enterprises etc. The water from such a neighborhood will be significantly spoiled by harmful chemical compounds.

So, let's start the actual drilling:

• The auger must be turned clockwise using four hands. That is, you will need an assistant. We turn the drill until it is completely deep into the ground, after which we remove it using a winch. We clear the blades from layers of soil and deepen the drill again.
• Thus, you need to reach waterproof soil. You can mark this layer by the composition of the wet soil that you selected on the aquifer.

Important: to level the walls of the well and clear it of layers of soil, you can use a bailer.

• The finished well is equipped with a casing pipe with a strainer at the end. Now you need to pump out some water using a pump. Over time, the liquid at the source should come out clean. But if after pumping the water is still cloudy, it is worth deepening the well another 1-2 meters.

You can learn more about creating a sand well with your own hands from the video:

Pipe deepening drilling

• If you are wondering how to drill a well yourself, you can use this method for greater convenience. Here it is necessary to prepare casing pipes, the diameter of which will exceed the diameter of the auger by several centimeters.
• First, you need to proceed according to simple auger drilling. As soon as manual drilling reaches 70-100 cm, you can install a pipe in the hole and deepen it under the influence of impact force using a sledgehammer.
• Well drilling continues inside the pipe. And each time, when removing the auger with a winch, it is necessary to deepen the pipe down to the aquifer.

Important: do not be overzealous with driving the pipe into the face itself. Otherwise, you may accidentally block the access of groundwater to your well. It's also worth noting that this method of source development does not include a filter. Therefore, it will be necessary to completely pump out the well several times and only then send the water for analysis.

• It is advisable to fill the annulus with strong cement mortar to prevent dirty groundwater and wastewater from entering the source.

Cable-percussion drilling

For those who do not know how to drill a well, we will reveal another way to develop a source. This method is the most powerful of all listed. Because the soil will be drilled under the influence of a large impact force. To complete the work you will need:

• Powerful and durable tripod made of metal pipes;
• Winch with steel cable;
• Impact glass made from steel pipe, weighted and having sections for cutting soil on one side;
• Bailer;
• Casing pipes with mesh filter.
• First of all, you need to prepare a special pit for the well. That is, we dig a site measuring 1.5x1.5x2 meters. It is advisable to cover it with boards so that the soil does not fall into the well during work.
• So, we install the tripod over the intended area so that the impact glass is located exclusively in the center of the tripod. We mount the winch and attach the shock glass to the steel cable.
• With the help of a neighbor (friend, brother), we influence the impact cartridge using a winch, sharply lowering the drill. The thread on the glass will cut into the ground, absorbing the cut layers.
• Raise the glass and clean it of soil residues.
• Thus, you now know how to drill a well without complex equipment.

Important: do not forget about good mesh filters that will prevent sand from getting into the well water.

But before working through the source manually, weigh the pros and cons. It is quite possible that it will be more profitable for your site to drill an artesian source.

Video about cable-percussion drilling: