The advantage of acrylic bathtubs is their lightness, but this point is also their disadvantage, since a rather fragile and thin structure may not withstand and burst upon impact or be damaged by the fall of a heavy object.
Agree, I wouldn’t want to spoil the new plumbing during installation. Overall, the installation acrylic bathtub Doing it yourself is not a difficult task. The main thing is to understand the principle of operation and adhere to the technology.
Below are various ways installation of the bathtub, the procedure for connecting the siphon and sewerage supply is described. All instructions are accompanied by visual photographs and video materials.
Bathtubs made of acrylic are very beautiful, they have original design and various color solutions. At the same time they have their own weak sides and vulnerabilities.
Therefore, it would be a good idea to find out what problems you may encounter during installation and subsequent operation, and how to prevent them.
Colored acrylic bathtub unusual shape will become a bright and original element that can decorate the interior of any bathroom
Among the advantages are:
- Plastic. Acrylic lends itself well to molding and subsequent processing. This property of the material determines the presence of a huge variety of shapes of acrylic bowls.
- Lightness. The acrylic bathtub is light in weight (15-25 kg), so its installation can be easily handled by one adult man.
- Priority heating technology. Acrylic itself is warm material. In addition, it has low thermal conductivity; bathtubs made of acrylic can retain heat for a long time; the water in them cools much more slowly than in cast iron structures.
- Maintainability. Plumbing fixtures and acrylic products in general lend themselves well to repair and restoration. If the damage is significant, then you can restore the bathtub using an acrylic liner, which is made for a specific design and then simply inserted into the old container.
As for the disadvantages, they are also present. We must not forget about the disadvantages. Following the recommendations below will help you avoid possible problems and extend the life of the acrylic bathtub.
To the disadvantages acrylic sanitary ware include:
- Sensitivity to high tº. Acrylic doesn't hold up very well high temperature. When heated above 60 degrees, it may become deformed, so do not pour too much into the bath hot water.
- Fragility. If you accidentally drop a heavy metal object, a step like uneven surface, its bottom can be pierced through.
- Vulnerability. Acrylic bathtubs are capricious - they cannot be rubbed with hard brushes or washed with powders containing abrasives, since the enamel is very sensitive and can be easily scratched by exposure to hard particles.
And it should also be noted, if not a disadvantage, then the inconvenience faced by those who first plunged into an acrylic bathtub. Due to the thinness of the material, the bottom may bend slightly under the weight of a person. However, you get used to this feature of an acrylic bathtub quite quickly.
Image gallery
Conclusions and useful video on the topic
Assembly of the frame and installation of a bathtub with a plastic screen is described in the following video:
Video instructions on how to properly assemble a factory metal frame for an acrylic bathtub:
Acrylic bathtubs of angular, round or asymmetrical shape are installed only on a factory-made metal frame. Manufacturers are making detailed instructions, according to which any man can cope with this work on his own. However, it is better to entrust the installation of a hot tub to specialists, since it requires the connection of complex electrical equipment.
Do you have anything to add or have questions about installing a bathtub? Share personal experience plumbing installation and please leave comments on the publication.
First of all, of course, a few words should be said about the manufacturing company acrylic bathtubs B.A.S. This company continues to surprise its consumers and partners, proving that bathtubs produced in Russia are no worse than their foreign counterparts.
The main products of this company are hydro and air massage acrylic bathtubs. Among the obvious positive aspects of acrylic bathtubs produced by BAS are the following:
- acrylic bathtubs from bas are manufactured using multi-layer polymer plastic from the senoplast company - a combination of acrylic and ABS plastic gives strength and reliability to the bathtub;
- the same plastic from senoplast also has an antibacterial effect, which protects the bathtub from the proliferation of various bacteria
- Bathtubs from bas are manufactured using high-quality Italian equipment, so the products can compete with European products
- acrylic bathtubs are reinforced with a steel frame, which is well protected from water
- the products are manufactured in Russia and therefore their features take into account the design of Russian bathrooms
Buyers about BAS bathtubs
I wonder what the buyers themselves say about acrylic bathtubs; reviews are quite easy to find on the Internet. It turns out that the majority of customers were very satisfied, saying that the acrylic bathtub from bas works great. Buyers happily share their impressions that the bathtub of this company:
- does not scratch, despite the fact that the shower periodically falls into it
- The side is very thick and you can sit on it
- the bath retains heat well, and therefore you can bathe in it for a long time, even if there is limited hot water
- The bathtub is equipped with excellent comfortable armrests
- takes up little space, all models are well thought out
- the only part that earned several negative reviews was the hydro and air massage system - they say that it does not last very long, and repairs are quite expensive
Another interesting point was that many buyers installed and assembled both an acrylic bathtub and a bathroom curtain on their own. Of course, not everyone can do this, but we can still assume that this indicates the quality of the product, since even an unprofessional assembler will do everything efficiently. However, the installation of a bas acrylic bathtub can be done by professionals - it all depends on the client’s capabilities. The instructions that come with the bathtub are quite clear and simple, so assembling the bas acrylic bathtub is not difficult.
Three great examples of BAS products: Atlanta, Florida and Laguna
One great example is the acrylic bathtub bas atlanta, which has certain advantages. So, the dimensions of this bathtub model are quite modest, it is suitable even for a small bathroom - 170 by 70 cm. However, the capacity is very good - 205 liters. Since bathtubs from BAS are mainly hydromassage, Atlanta is no exception - it is equipped with six nozzles - three on each side.
The required kit includes a standard set:
- metal frame that guarantees the strength of the bath
- legs under the bathtub, which allow you to adjust the height of the bathtub and ensure its stability
- a front panel that will cover the space under the bathroom and give the interior a complete look
- necessary device for draining and overflowing
In terms of design and space optimization, this is a very simple, medium-sized rectangular bathtub that is quite comfortable, but does not take up too much space or distract too much attention, so it will easily fit into almost any modern design.
Another example of an excellent bathtub is an acrylic bathtub - this is a corner asymmetrical bathtub. It is quite compact in itself - length 160 cm and width 88 cm, and at the same time it also has a beveled corner, so it will become ideal option for a small room. Although her style is quite simple and elegant, if desired, you can highlight her - for example, create a visually separate space for her, using decorative elements, finishing with tiles of a different color or shade, additional shelves, etc. In addition to its ergonomic design, this bathtub also has an interesting shelf for hygiene items, or even to sit on.
The equipment here is standard - the same as in Atlanta. The capacity is also 205 liters. But there are more hydromassage jets - there are eight of them.
The last one to consider, of course, is a model such as an acrylic bathtub bas lagoon, which is somewhat similar to the Florida model. However, Laguna is larger in size - 170 by 110 cm. The capacity is also much larger - 295 liters. And the number of hydromassage nozzles is the same - eight pieces. The equipment is standard.
This bathtub is suitable for a medium-sized room, due to the fact that although it is asymmetrical, it is still quite large and is unlikely to fit well in a small room. This model is also very conveniently equipped with a shelf for bathroom accessories and has ergonomic design. At the same time, it will most likely be one of the main elements in the design of the room, this is facilitated by its rather large size. Therefore, you can highlight it with directional colored lighting or other decorative options. Also, great idea will hang large mirror next to the bathroom, so that it expands the space, and the bath no longer seems something bulky.
In addition to the standard equipment, BAS offers its customers a fairly large selection additional options. These additional features can be divided into several groups:
- Aero and hydromassage lotions: various types of massage - back, shiatsu, foot; aeromassage from 6 to 12 nozzles, hydro-aero-pipe massage.
- Faucets: cascade mixer or even the whole set: spout, mixer, shower holder.
- Backlight: various types lighting and chromotherapy.
- Pleasant little things: headrest, armrests, cleaning products for the massage system or the bath itself, a pillow for the on and off buttons.
BAS provides its customers with truly ample opportunities according to the choice of model and set of bathtub configurations, plus you can choose a design curtain.
OPERATION OF BAS BATHTUBS
Thank you for purchasing this bathtub. trademark"BAS". Hydromassage baths "BAS" are modern technologies and original lines that provide the comfort of hydromassage, which will improve your health and give you many pleasant moments.
This manual describes the bathtubs' functions, installation requirements, care and operating methods.
PRECAUTIONS
In order for the bath to be beneficial for you, to work for a long time and reliably, a number of conditions must be met:
1. If your body has problems with the functioning of the cardiovascular system, then consult a doctor (to what extent is hydromassage beneficial for you).
2. Consider installing filters (for water purification) - this will increase the service life of your faucets and hydromassage bath equipment.
3. Do not turn on the hydromassage without filling the bathtub with water.
4. Do not allow the bathtub to be walled up in tiles, panels or hard mortars, restricting access to hydromassage equipment that prevents the bathtub from extending to a distance of at least 0.5 m from the wall.
5. The bath is connected to a single-phase alternating current network with a voltage of 220V. To avoid defeat electric shock, the bath must be grounded through a socket with a connected grounding contact.
TECHNICAL DESCRIPTION AND EQUIPMENT
The standard configuration of bathtubs is shown in the following table
| №n/n | Type of components | List of configurations and quantity, pcs. | ||||||
| A | B | C | D | E | F | G | ||
| 1 | Acrylic bathtub (frame, top panel clamps and additional equipment) | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| 2 | Bathtub fitting (drain-overflow) with siphon \ without siphon | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| 3 | Support threaded rod M12 | 4 | 6 | 6 | 8 | 7 | 5 | 7 |
| 4 | Leg PVC baths M12 | 4 | 6 | 6 | 8 | 7 | 5 | 7 |
| 5 | Corner for panel fastening | 2 | 2 | 3 | 2 | 2 | 2 | 4 |
| 6 | Decorative clip (with press washer) | 4 | 4 | 6 | 4 | 4 | 6 | 8 |
| 7 | Washer M12x36x3.4 | 4 | 4 | 6 | 4 | 4 | 4 | 8 |
| 8 | Nut M12 | 12 | 16 | 18 | 20 | 18 | 14 | 22 |
| 9 | Mounting screw 4.2x25 | 4 | 4 | 6 | 4 | 4 | 6 | 8 |
| 10 | Manual | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
Equipment List A-for bathtubs models “CAMERON”, “LIMA”, “TESSA”, “VERONA”, “IBIZA”, “BREEZE”, “ALEGRA”, “VECTRA”, “MALDIVE”, “STYLE”, “SAGRA”, “ATLANTA” ", "NEPTUNE", "MALTA", "AKHIN", "FLORIDA", "FANTASY";
Equipment list B-for bathtubs of the “INDICA”, “JAMAICA”, “LAGUNA” models;
Equipment list C-for bathtubs of “CAPRI” models;
Equipment list D-for bathtubs of “FIESTA” models;
Equipment list E-for bathtubs of “NIKOL” models;
Equipment list F-for bathtubs of the “RIOLA”, “XATIVA”, “IRIS”, “IMPERIAL”, “MEGA”, “DROVA” models;
Equipment list G-for bathtubs of “RIVIERA” models;
Additional equipment includes: hydromassage, back massage, Shiatsu massage, aeromassage, lighting, chromotherapy, control panel, mortise mixers and handles.
Depending on the bathtub model, the manufacturer provides panels (screens) for bathtubs (front, side), shower curtains and headrests, which are not additional equipment and are not included in the kit. The manufacturing company reserves the right to make changes to the design and configuration of the bathtubs.
TRANSPORTATION OF BATHTUBS
The bathtub must be transported only in a horizontal position. When transporting and installing the bathtub, care must be taken not to damage the piping and electrical systems. The bath should be moved only for the body or frame. Must be avoided mechanical damage bath body, panel, and also exclude the possibility of exposure to chemically active reagents on the surface of the product. When transporting in the cold season, before installation, the bath must be kept at room temperature at least 6 hours.
ATTENTION! It is strictly forbidden to move the bathtub by pipelines, nozzles, handles and other equipment! Inspect the product for compliance with the order, absence of mechanical damage, completeness, availability of accompanying and warranty documentation.
REQUIREMENTS FOR THE BATH INSTALLATION LOCATION
The room in which the bath is installed must meet the following requirements:
Tiled and Finishing work must be completed;
It must be possible to easily access the components and assemblies of the bathtub for its preventive warranty maintenance and repair;
Availability of a power line with the required parameters and a socket with a connected grounding contact. The power supply to the bathtub connection point must be provided by a double-insulated electrical cable with a cross-section of at least 2.5 mm2 and is in accordance with the norms and standards of the EEC;
Availability of water supply and sewerage. Sewage pipe the bathroom should not rise above the floor at the connection point by more than 10 cm. If this is not possible, then it is necessary to provide a podium under the bathtub;
REQUIREMENTS FOR INSTALLING A BATH
Installation of the bathtub should be carried out only by qualified specialists, in compliance with the following requirements:
Installation of a bathtub without a frame, as well as with a modified frame, is not allowed. The legs are used to level the bathtub and adjust the gap between the bathtub panel and the floor. The bathtub must rest on all support points to prevent uneven distribution of the load and, as a result, the appearance of microcracks in the bathtub body;
It is not allowed to embed the bathtub in tiles, panels or hard mortars. To avoid moisture getting under the bathtub or on the hydromassage equipment, the seams between the bathtub and the wall must be sealed with plumbing silicone.
Avoid contact with dirt and construction dust onto the surface of the bath. This may cause clogging and failure of the hydromassage equipment or lead to scratches on the surface of the bathtub during subsequent unprofessional cleaning.
When carrying out work on the removal of water supply and sewerage pipes, it is necessary to take into account the linear dimensions of the bathtub. Otherwise, the connection may be difficult, since the pipe outlets may rest against the stiffeners, units and fittings of the bathtub, and the bathtub cannot be installed close to the walls. Structural changes in the arrangement of equipment and pipelines of the bath, cutting of mounting clamps, and so on are strictly prohibited.
The electrical wiring of the room must have an individual differential switch 30mA, magnetothermo 2.4-4A or another common connection (CEI-64-8) and installed in the common switchboard of the room. It is strictly forbidden to install this switch under the bathtub!
ATTENTION! Failure to comply or not to fully comply with the above requirements does not provide for the preservation of warranty conditions for service or repair for such a bathtub.
BATH INSTALLATION
Install the bathtub on the legs (Fig. 1). The manufacturing company allows the legs to be equipped with an M12 bolt, instead of the corresponding threaded rods. Feet configuration A(Fig. 1) (2 pcs.) - installed on the front (front) side of the bathtub, along the edges, on the left and on the right (for a bathtub " RIVIERA" - 4 pcs., all at the front). Feet configuration B(Fig. 1) - other remaining front and rear legs. The legs are connected to the frame using the upper pair of M12 nuts, which also serve to adjust the height of the bath.
Install a drain-overflow device on the bathtub (Fig. 2), a siphon (may not be included in the kit), and adjust the bathtub in height. The distance from the floor level to the bottom point of the siphon must be at least 15 mm. Make sure that the bathtub is adjusted and rests on all points of support.
Install the panel onto the bathtub by snapping it onto the upper fasteners (Fig. 6 and 7). On some models of symmetrical and asymmetrical “BAS” bathtubs, it is possible to trim the panels to length (no more than 2 cm per side). In addition, if you plan to install a side panel on your bathtub, then first install the top fasteners under it that come with the side panel. Adjust the verticality of the panel. The bottom of the panel should be adjacent to the plane of the corner corner installed on the outer legs. The seating depth of the angle is adjusted by the lower pair of M12 nuts. The corners should be equally adjusted in height and be symmetrical relative to the panel.
Using a drill with a diameter of 3.5 mm (the size indicated is for a 4.2x25 mm self-tapping screw), drill in the lower corners and panels through holes(Fig. 4 and 5).
Remove the panel from the bathtub and connect it to the sewerage and water supply systems (see Connecting the bathtub to the water supply and sewerage network), as well as to electrical network 220 V (see Connecting the bath to the electrical network). After this, carefully move the bathtub tightly against the wall, and once again make sure that it is stable at all points of support, and all connections are made correctly.
6. Place the panel on the bathtub and fix its bottom in drilled holes self-tapping screw with a press washer (Fig. 8).
7. Close the head of the screw with a decorative plug (Fig. 9).
ATTENTION! TO AVOID MOISTURE GETTING BEHIND THE BATH, MUST TREAT THE SEAM WITH PLUMBING SILICONE AROUND THE ENTIRE PERIMETER OF THE BATH!
CONNECTING THE BATHROOM TO THE WATER SUPPLY AND SEWERAGE NETWORK
The connection of the bathtub to the water supply and sewerage network must be carried out by a qualified plumber.
The bathtub kit includes a semi-automatic drainage device, which, after installing it on the bathtub, is connected to sewer network stationary, through flexible corrugated or rigid PVC pipe(not included). A sewer drain with a diameter of 40-50 mm is installed at the bathtub installation site in the floor or wall, taking into account the linear dimensions of the bathtub. When placing the drain pipe in the wall optimal height the distance is considered to be no more than 2 cm from the floor level to the bottom edge of the pipe.
Connecting the bathtub to the water supply network if it is equipped with a mortise mixer. The network pressure should be 3-5 atm. At pressures above 5 atm, pressure reducers should be installed and adjusted to the specified standards.
Places for connection to the water supply system must be placed taking into account the linear dimensions of the bathtub and its units and equipped with taps disconnecting from the main line. Connection to the system is made through a flexible plumbing line ( water hoses). The length of the hoses must allow the bath to be moved from the walls and a distance of at least 0.5 m. Recommended use of water purification filters. The absence of filters can lead to clogging of hydromassage nozzles and metal scale entering the ceramic mixer cartridge, which will lead to their failure.
ATTENTION! Inset mixers are supplied with a set flexible hoses standard sample. If the length of the flexible line is not enough for connection to the system or connection between the elements of the mixer, then it is purchased separately, taking into account your dimensions for connection. The bathtub manufacturer is not responsible for the nature of the set of mortise mixers, for damage to the elements of the hydromassage system caused by their contamination when using unfiltered water containing rust, sand, chemically active impurities, as well as for breakdowns or incorrect operation of the bathtub equipment connected to the system water supply with non-standard pressure in it.
Leave the bathtub unattended when filling it with water. Overfilling the bath with water can lead to failure of the air massage system, without maintaining the warranty conditions for the product.
Rotate the drain-overflow cover around its axis or while placing a weight on the bathtub plug.
CONNECTING THE BATH TO THE ELECTRICAL NETWORK
The electrical equipment of the bath is powered from a single-phase alternating current network, in accordance with the table below.
| Function | Voltage, V | Frequency, Hz | Power, kWt* |
| Hydromassage | 220/240 | 50 | 0,9-1,5 |
| Aeromassage | 220/240 | 50 | 0,7-0,9 |
*power is indicated depending on the bath model
Connecting the bath to the electrical network must be carried out by a qualified specialist with clearance group 3 or higher. The procedure for connecting hydromassage baths to the network:
Yellow-green wire - “grounding”;
Brown wire - “phase”;
Blue wire - “zero”;
The bath's power supply must be connected only through a separate residual current device (RCD), rated 30 mA and located outside the bathroom.
A detachable type of connection of the bath to a 220 V network is allowed. Depending on the configuration of the bath, elements of hydromassage equipment may not be equipped with electrical plugs for connection. In this case, they are purchased separately and installed independently. Each piece of equipment intended to be connected to the network must have an individual connection to the electrical network.
Connect units together, into one plug, etc.
Use the bathtub with a socket or plug without a working ground contact.
Ground the bath through heating, plumbing and sewerage equipment.
Operating the bathtub with a damaged electrical cord or with a faulty or unconnected ground.
Conduct engineering works when the bath is plugged in.
HYDROMASSAGE AND ADDITIONAL EQUIPMENT
The following elements of hydromassage equipment can be located on the bathtub (see View A):
Email Hydromassage motor with hydraulic pump
Air massage compressor
Bathroom control buttons and controls
hydromassage jets (reverse side)
piping system
Additionally, they can be installed on the bathtub
air massage (installed in the bottom of the bath, see Fig. 1)
Inset mixer (see Fig. 2)
Back massage (see figure 3)
Shiatsu massage (back massage or back massage + foot massage) (see Fig. 4)
Chromotherapy (see Figure 5)
Backlight (see Figure 6)
Headrests (see Figure 8)
BATHROOM CONTROL
The bath functions are controlled using the following equipment:
A) Hydromassage jets.
Provide adjustment of the direction and strength of hydromassage jets. The direction of the jet can be easily changed by turning the nozzle nozzle within a 30-degree angle. The force of the water jet is regulated by rotating the nozzle nozzle around its axis. The maximum jet flow is achieved by fully opening the jet nozzle counterclockwise (open nozzle).
B) On/off button Hydromassage functions with air supply regulator (RPV). Provides on/off. hydromassage system by pressing in the center. The RPV dispenses the amount of air mixed with the stream of water during operation of the hydromassage system, due to the injection process. By turning the knob you can change the amount of air flowing along with the stream of water from the hydromassage nozzles. The power of the jet increases with the supply of air into it.
IN) On/off button Aeromassage functions (chromotherapy lighting). Provides on/off switching of the air massage system. When turned on, the compressor pumps air under pressure through air nozzles installed at the bottom of the bath. At the same time, small air bubbles burst to the surface, massage and enrich the skin with oxygen. Can be used to turn on/off. Chromotherapy lights.
G) Crane balance (turbo pool).
Switches the operating modes of the hydromassage system between the general hydromassage function and the back massage function (Shiatsu massage). Adjust the desired distribution of water supply using the indicated functions by turning the “flag” of the switch.
D) Electronic remote control for bath functions (No. 2).
Buttons for adjusting the power of the air massage function
On/off button air massage functions
On/off button Chromotherapy (backlight) functions
On/off button Hydromassage functions
E) Electronic (touch) remote control for bath functions (No. 3).
Remote control power on/off button
Button to turn on/off the hydromassage function
Button to turn on/off the backlight/chromotherapy function
Multifunctional button for switching operating modes: radio station frequency ( MHz) / radio station channel number ( ch) / radio station frequency setting mode (flashing sign TUNE) / volume control mode ( d) / air massage power level adjustment mode (number from 1-10 ). Also used as a selection confirmation button when recording radio channels into memory. Up to 10 configured channels can be stored in memory ( CH).
Buttons for setting modes: volume level / radio station frequency / radio station channel number / air massage power level. The setting is carried out depending on the mode selected by button 5 ( SET).
Radio on/off button.
Button to turn on/off the air massage function.
ATTENTION! If your bathtub is equipped with a control panel, then when the water level in the bathtub is lower than required, all functions are turned off, except for the radio and air massage.
HOW TO USE HYDROMASSAGE BATHS
ATTENTION! Never turn on the whirlpool until the water reaches a level 5-6 cm above the main whirlpool jet opening. Avoid high thermal effects (above 65 degrees Celsius) on the surface of the product - this can lead to its damage! It is prohibited to turn on the hydromassage function when the jet nozzles are closed. Before turning on the hydromassage system, make sure that the jet nozzles are not directed upwards and that the balance valve is not in the back massage position (Shiatsu massage). During operation of the hydromassage, it is forbidden to block the grille of the water intake valve, preventing the flow of water into it. After using the bath and draining the water, it is recommended to blow out the air massage jets by turning on the air massage function for 1 minute.
Never use the bathroom after taking alcohol or taking medications. Hydromassage in medicinal purposes can be carried out only on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath improves your health; taking a warm or slightly hot bath relieves stress. To relax muscles and relieve pain, take a bath at 40 degrees Celsius. The first hydromassage session, which should only be performed in warm water, should last no more than 10 minutes
The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel drowsy while taking a bath, turn off the hydromassage device for a while and cool the water.
Contraindicated for overweight people hydromassage baths at water temperatures exceeding 38 degrees Celsius.
BATH CARE
For daily bath cleaning, use a liquid cleaner that is harmless to acrylic and plastic surfaces(see instructions for the cleaning product), as well as a cloth made of soft fabric. The manufacturing company offers you a specialized cleaning product “TIM-PROFI”, adapted to our products. To maintain the shine of the bathtub, it can be wiped with a cloth with a polishing agent. To clean the bathtub, use only soft cloth napkins.
Deposits on the surface in the form of scale are removed with a soft cloth moistened with lemon juice or wine vinegar.
Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly scrubbing with a fine-grained sandpaper(No. 1000/2000) with water. You can restore the shine of the surface with a liquid polish.
ATTENTION! To remove dirt from the surface of the whirlpool bath, never use metal brushes or tools, as well as solvents or detergents with abrasive additives. Also avoid contact of ammonia or chlorine with brass and chrome parts.
CLEANING THE BATH HYDRAULIC SYSTEM
This type of cleaning when using hard water (over 15 salt deposits per 1 cubic meter water). In addition, it is recommended to clean the bathtub hydraulic system Twice a year in the following way:
Fill the bath hot water(40 degrees Celsius).
Pour in liquid detergent at the rate of 2g per 1 liter of water and run the hydromassage system for about 5 minutes.
After this, turn off the hydraulic pump and drain the water from the bath.
Refill the bath cold water and turn on the hydromassage for 2 minutes.
Drain the water and wash the bathtub (see “Bathtub Care”).
SIMPLE MALFUNCTIONS, CAUSES AND METHODS OF THEIR ELIMINATION
| Occurring fault | Possible reason | Remedy |
| Hydraulic pump does not turn on | No voltage in the power circuit (220 V network) | Call a specialist (electrician) |
| The hydromassage button does not turn on (air massage, lighting, chromotherapy) | The plastic tube connecting the button and the electro-pneumatic valve has come off the function activation button. | Attach the plastic tube to the base of the button and restart the system |
| Jet nozzles are closed | Rotate counterclockwise to open nozzles | |
| The hydraulic pump works, but no water flows from the jets | Formation of an “air lock” in the hydromassage system | Disconnect the bathtub from the 220V network, fill it with water and, loosening (no more than 1 turn!) the upper nut of the hydraulic pump tee, bleed the air from the system. After this, tighten the nut tightly and turn the system back on. |
| Increased vibration in the hydraulic pump | The engine mount is loose metal frame baths | Tighten the engine mounting bolts. |
Technical features
IN Lately acrylic bathtubs are very popular among buyers. A wide range of sanitary products offers options for different bathtubs. Many modern companies demonstrate high-quality products that are easy to use. Among them, the domestic brand Bas stands out, which produces interesting models hydromassage baths. With their help you can raise the quality of your holiday to a new level.
Technical features
Russian company Bas has been delighting its customers with bathtubs, shower cabins and bathroom accessories for over 15 years. Products are manufactured using high-quality Italian equipment in strict accordance with technological parameters and international standards. Products are sold not only in Russia, but also in Kazakhstan and Belarus.
Bas bathtubs are made from high-quality acrylic, thanks to which the product is resistant to corrosion and other types of chemical attack. This material is characterized by its plasticity, so making bathtubs using it is not a labor-intensive process, the result of which is characterized by high level quality.
The wide range of the Bas brand showcases classic and modern models bath white, among which you can definitely choose the most suitable option for small and large bathrooms. Bathtubs are produced using two different technologies.
- The traditional method is “SprayGun”. It strengthens the acrylic base polyester resin and glass fiber.
- The method developed Italian company SIRTEK. In the manufacture of the frame, a complex two-component composition of high-strength polyurethane foam is used.
The manufacturing process itself includes the formation of the shape of bathtubs from a polymer multilayer material - ABS sheets. Using high-quality equipment, it is given the required shape of the future product and acrylic is applied, which will account for 10% of the sheet thickness. This product is characterized by a high degree of strength and impact resistance.
The manufacturer Bas also offers its customers a model range with a hydromassage function. The set of such products includes nozzles that, using the directed movement of water jets, help achieve complete relaxation and help obtain maximum health benefits.
Advantages and disadvantages
Bas products are characterized by a number of advantages.
- High quality materials. In the manufacture of products, raw materials are used from large European manufacturers that have a positive reputation. The color of the products does not fade with age, the surface remains smooth, and the frame does not bend under heavy weight.
- Impact resistance. Production technologies make the surface of the bathtubs resistant to mechanical damage, significantly increasing their service life.
- Antibacterial surface effect. It prevents bacteria from multiplying in a humid environment, making using the bathtub an even more comfortable and safe procedure.
- Easy installation. The product instructions contain complete installation information. You can install the bath easily and quickly yourself or use the professional assembly service from the company.
- Convenient operation. The product form provides all the necessary nuances of its use. Smooth lines and the necessary recesses for comfortable spending time and quality rest attract the attention of buyers who value comfort.
- Hydromassage function. Models with this function make the process even more enjoyable, positively influencing blood circulation in the body and allowing you to reduce the intensity of cellulite and increase stress resistance.
The disadvantages of products from the Bas brand include some characteristics.
- Lack of support points. When installing bathtubs of complex shapes, you may encounter the problem of a lack of support points for comfortable use of the product. This problem can be solved by contacting the company’s service center or independently using available tools.
- Plastic nozzles. Buyers may have problems with leaking injectors that will have to be replaced.
- Price. For many buyers, the price category for acrylic products seems overpriced, although the manufacturer claims the availability of its products and the ability to choose a model for any budget.
The manufacturer's products have a significant list of advantages, but no one is immune from unpleasant incidents. In any case, Bas consultants are patient with their clients and are ready to delicately solve any problem that arises.
Criterias of choice
The lineup sanitary products from the Bas brand are quite large. Among them, you can easily find a bathtub that will meet all the needs of customers. Choosing suitable product, the first thing the buyer relies on is the size of his bathroom. Especially for this purpose, the manufacturer’s range includes products of different sizes. Dimensions on average vary from 1300x700 to 1800x1500 mm. For very small bathrooms you can choose corner products, which significantly save space.
Models “Nicole” 170x102 cm and “Fantasy” 150x88 cm have similar characteristics.
Depending on the functionality, conventional acrylic bathtubs and hydromassage models are distinguished. In fact, every model provided in the catalog can be equipped with a hydromassage function, the only difference will be in price.
Another important parameter is the shape of the product. The Bas brand range includes bathtubs of the following shapes:
- oval;
- rectangular;
- corner;
- asymmetrical;
- non-standard.
When choosing, it is worth considering that the more complex the product, the more support points it requires, and the more prone it is to deformation.
It is better to stick to more traditional oval or rectangular models. Products are attractive to buyers not only due to their appearance and quality. Bas bathtubs have an ergonomic shape, which is specially designed taking into account the characteristics of the human body and its curves. In such models, taking water procedures will be pleasant and comfortable.
The weight parameter for acrylic bathtubs does not play a special role, since such products weigh much less than cast iron options and do not cause difficulties with lifting to the floor and during the installation process.
Range overview
In the manufacturer's catalog, products are divided by product shape for a comfortable search for a suitable product.
Rectangular baths
Standard model "Ibiza" has dimensions 1500x700 mm. It is ideal for a small bathroom, and due to its depth of 430 mm it will allow you to cover it with water. most bodies. The height of the bathtub screen is 530 mm, it holds 175 liters.
The ergonomic shape will allow you to enjoy water procedures while feeling comfortable. With the hydromassage function it will include 6 nozzles - 2 large and 4 small. It may also include a shiatsu spinal massage function complete with a faucet regulator to balance the control of water flows.
The kit includes several lighting options, LEDs, and an electronic remote control. There are several faucets to choose from: 2-position with switch to shower or cascade spout.
Models will have similar characteristics "Verona" 150x70 cm, "Malta" 170x75 cm and "Rio" 170x70 cm.
Product "Jamaica" with dimensions of 180x80 cm it will be an excellent tool for quality relaxation. Thanks to its large size and depth of 430 mm, it will allow the body to be completely immersed in hot water. The smooth curves of the bathtub will make you feel comfortable. The presence of 8 or 12 jets for air massage will help you quickly relax and relieve stress.
Water volume – 230 l, screen height – 630 mm. Like the previous model, it includes backlighting, LEDs, and an electronic remote control. The kit also includes the possibility of a shiatsu spinal massage and cascading 2-position mixers.
It is also worth paying attention to the “Fiesta” model 194x90 cm.
Rectangular bath "Lima" size 130x70 cm is suitable for a small bathroom or for a children's bathroom due to its small dimensions. It holds only 95 liters and is characterized by a depth of 420 mm. May include a hydro- (6 nozzles) or air massage function (8 or 12 nozzles). The screen height is 540 mm. It is possible to install a spinal massage and LEDs. Backlight and other functions can be adjusted using electronic remote control. In addition to the options considered, current rectangular-shaped products are models "Atlanta" 170x70 cm and "Indica" 170x80 cm.
Asymmetrical baths
Product "Lagoon" 1700x1100 mm – corner option bathtubs, which is popular among buyers due to its ergonomics and stylish appearance. Despite its compact size, it has sufficient dimensions for the owner to comfortably enjoy water treatments. It holds up to 295 liters and has a central depth of 440 mm. Screen height – 550 mm. Includes the ability to install hydromassage with 6 nozzles or air massage (8, 12 nozzles). It has a special recess for easy foot massage.
Model "Alegra" has dimensions 1500x900 mm. Unlike the previous model, it does not have a side, due to which it receives a larger area for water procedures with the ability to save space in the bathroom. The depth in the center is 450 mm, holds 220 liters of water. The simple design features smooth lines and ease of use. Massage jets are distributed along the walls of the bathroom for better relaxation.
Also popular are the following models of asymmetric bathtubs: "Capri" 170x80 cm, "Sagra" 160x100 cm, “Florida” 160x88 cm.
Symmetrical baths
For those wishing to purchase a “mini-jacuzzi” for themselves, you should pay attention to the product "Mega" 1600x1600 mm. It has positive reviews due to its ease of use and the possibility of getting quality rest due to the successful distribution of nozzles: for hydromassage - 6, for aeromassage - 8 and 12. It is possible to backlight and include LEDs in the kit to create an atmosphere and mood. Capacity is 450 l, bath depth is 480 mm, and screen height is 610 mm. There is a compartment for the possibility of receiving a foot massage without filling the bathtub completely with water.
Instructions for acrylic bathtubs from Bas
Thank you for purchasing the BAS brand bathtub.
- Preface
“BAS” baths are modern technologies and original lines that ensure the comfort of taking water procedures.
This manual describes the bathtubs' functions, installation requirements, maintenance and operating methods.
Attention: In order for the bath to be beneficial for you, to work for a long time and reliably, a number of conditions must be met:
1) Consult your doctor to what extent taking a bath is beneficial for you.
2) Consider installing filters for water purification.
3) Do not turn on the hydromassage without filling the bath with water!
4) It is forbidden to seal the seams between the wall and the bathtub with rigid building materials (ceramic tile, curbs, mortar, etc.)
- Technical description
Standard equipment for a hydromassage bath:
1. Acrylic bathtub - 1 pc.
2. Metal frame - 1 pc.
3. Legs - 4-8 pcs. (depending on model)
4. Panel clamp - 2-4 pcs.
5. Self-tapping screws for fastening the acrylic panel - 5-12 pcs.
6. Additional equipment: acrylic panel (screen), drain-overflow device, back massage, aeromassage, etc. (at the buyer’s request)
Transporting bathtubs When transporting and installing a bathtub, care must be taken not to damage the piping systems and electrical equipment. DO NOT: carry the bathtub by the piping and electrical wiring. It is necessary to avoid mechanical damage to the bath body and screen, and also to exclude the effect of chemically active reagents on the surface of the product.
Instructions for preparing a site for installing bathtubs:
1. A plumber performing work on the removal of hot and cold pipes cold water, must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may rest against the stiffeners, units and fittings of the bathtub. This means that the bathtub cannot be installed close to the walls.
2. The bathroom drain pipe should not rise above the floor by more than 10 cm. If this cannot be ensured, then a podium must be made.
3. The legs serve to level the bathtub, so additional supports must be installed under the supporting structure of the bathtub.
4. Electrical wiring for the bathtub equipment must be made with a double-insulated cable with a cross-section of 2.5 mm2.
System protection should be based on differential (multiple) shutdown (1fn=30 mA). The power cable must comply with EEC regulations and standards
- Electrical system
The installation of the electrical system must be carried out by a professional electrician with an electrical safety clearance group of at least group 3. The power supply wiring for the lighting and hydro-air massage system of the bathtub must have a “Residual Disconnection Device” (RCD) with a rating of 30 mA.
- Attention:
Connect the electrical cable in the following order: blue wire— “zero” brown wire — “phase” yellow-green wire — “grounding” The power supply for the lighting and hydro-air massage system of the bathtub must be connected only through a separate RCD with a rating of 30 mA. The RCD must be located outside the bathroom. It is strictly prohibited to connect the power supply to the lighting or hydro-air massage system of the bathtub through a plug and socket.
Using the lighting system without water in the bath is strictly prohibited.
- Name V Hz kW
- Hydromassage 220/240 50 0.9-1.5
- Air massage 220/240 50 0.7-0.9
Power is indicated depending on the bath model.
- Equipment for hydro and aeromassage includes:
1. hydraulic pump
2. compressor for air massage
3. function activation buttons and hydromassage power control
4. hydromassage jets (back side)
5. piping system
- Optional equipment
aeromassage (the jets are at the bottom of the bath)
hand shower, cascade, mixer
backlight
back massage
headrest
pen
- Bathtub Installation Guide.
1. Before installing the screen, first mark the location of the centers of the screen mounting plates on the front side of the bath with a pencil or felt-tip pen.
2-5. Next, you need to screw 4 M 12 nuts onto the mounting legs, use two M 12 nuts to screw the mounting legs to the bathtub frame, and use the remaining two M 12 nuts and two M 12 washers to secure the screen mounting corner on the mounting leg so that it reaches the edge of the screen . Attach the screen to the bath and use a drill dia. Make 3.5 mm holes in the corners of the screen mounting (it is recommended to perform this operation after first removing the screen).
6-7. Mark on the top of the screen the points with the centers of the screen mounting plates already marked on the front side of the bathtub, placing them at a distance of 1.5-2 cm from the lower edge of the front side of the bathtub. In the marked areas of the screen, use a drill with a diameter of 3.5 mm to drill holes for self-tapping screws. Next, use the same drill to make holes in the mounting plates of the screen (it is recommended to perform this operation after first removing the screen).
8. Using the legs, adjust the bathtub to the height of the acrylic panel, taking into account the zero level of the upper plane of the bathtub.
9. Install the drain and overflow device on the bathtub, screw on the siphon (not included in the kit) and connect to drain pipe bathroom
10-11. Having aligned the screen with the bathtub embedded parts, it is necessary to screw self-tapping screws into the holes, and then put plugs on them.
12. After installing the bathtub, remove the protective film.
13. Install the bathtub wall bracket. A wall fixing is offered to enhance the rigidity of the bathtub.
- ATTENTION:
It is prohibited to seal the seams between the wall and the bathroom with hard building materials (ceramic tiles, curbs, mortar, etc.) If the above is not observed, warranty repairs will not be carried out
Instructions for using hydro-, aero-massage, back massage, water illumination (mechanical activation of functions).
- Buttons for turning on hydro-, aero-massage, water lighting. (on and off - by pressing your finger inward)
- Switch for hydromassage and back massage. (simultaneous operation of functions is possible)
- Power regulator for hydromassage and back massage. (turn the knob clockwise)
Electronic (touch) control of hydro-, aero-massage, chromotherapy functions. (1, 2 — air massage power control; 3 — on/off air massage function; 4 — on/off hydromassage function; 5 — on/off chromotherapy function)
- The hydromassage and chromotherapy functions are automatically turned off if there is no water in the bathroom. The air massage is turned off manually after the jets have been purged.
Bathroom care
When cleaning the bathtub, use a liquid cleaner that is harmless to acrylic and plastic surfaces (see cleaning product instructions). The manufacturer offers you a specialized cleaning agent “TIM-PROFI”, adapted to our products. Clean stains with a soft cloth.
Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly sanding with sandpaper (No. 1000/2000) and water. You can restore the shine of the surface with a liquid polish.
- Cleaning hydraulic system baths
This type of cleaning is performed using hard water (over 15 salt deposits per cubic meter of water). It is recommended to clean the bathtub hydraulic system at least 2 times a year as follows:
1. Fill the bathtub with hot water (40C).
2. Pour in liquid detergent at the rate of 2g per 1 liter of water and run the hydromassage for about 5 minutes.
3. After this, turn off the electric pump and drain the water from the bath.
4. Fill the bathtub with cold water again and turn on the hydromassage for 2 minutes.
5. Drain the water and wash the bathtub (see “Bathtub Care”).
The manufacturer offers you a specialized cleaning product for the hydraulic system, adapted to our products.
WARNING: Never use metal brushes or tools, or solvents or detergents containing abrasives to remove dirt from the surface of the hot tub. Also avoid contact of ammonia or chlorine with brass and chrome parts of the bathtub.
- How to use hot tubs
It is prohibited to turn on the hot tub when the hydromassage jets are closed and the water level is 5-6 cm below the jet opening. Never use the bathroom after taking alcohol or taking medications. Hydromassage for medicinal purposes can only be performed on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel drowsy while taking a bath, turn off the hydromassage device for a while and cool the water.
For overweight people, hydromassage baths at water temperatures exceeding 38 C are contraindicated.
Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upward.
- The simplest malfunctions, their possible reasons and solutions.
| Occurring fault | Possible reason | Remedy |
| There is no voltage in the network. | Call a specialist (electrician). | |
| The hydraulic pump does not turn on. | The plastic tube connecting the button and the pump came off the hydromassage button. | Turn off the voltage. Attach layer. tube to the base of the button and turn the system back on. |
| Jet nozzles are closed. | Turn counterclockwise to open the nozzles. | |
| The hydraulic pump works, but no water flows from the jets. | The piping system is clogged. | See the "Bathroom Care" section. |
| Increased vibration in the operation of the hydraulic pump. | The attachment of the motor to the metal frame of the bathtub has become loose. | Turn off the voltage. Tighten the engine mounting bolts. |
The manufacturer reserves the right to make changes to the design and configuration of bathtubs.
In winter, the product is installed in a warm room after 6 hours from the moment the bath is delivered to the client
If a drain or overflow is installed in a manner not provided by the manufacturer, the bath will be void of warranty.
Active substances must not come into contact with the surface of the product. chemical substances that can damage the acrylic layer.
High (above 80C) thermal effects on the surface of the product are prohibited.
Installation (installation) of the bathtub (shower curtain) and the equipment included in the kit is carried out by the buyer with the involvement of specialists licensed to carry out this type of work. The installation warranty is provided by the installer with a note in the warranty card.
Installation of products must allow easy access to components and assemblies attachments, as well as to connecting hoses supply of water and air.
Dear buyer! The manufacturer sets the warranty period for bathtubs to 10 years. This warranty period covers all equipment, except for: drainage and overflow devices, hydromassage, air massage and any other additional equipment (see clause 7, page 1 of this manual), for which the warranty period is 2 years.
- Warranty service is not provided in the following cases:
– non-compliance with installation rules and operating conditions;
– loss of a receipt or warranty card;
– negligent storage or transportation by the owner, trade or transport organization;
– attempts at unqualified repairs;
– mechanical damage, traces of exposure to chemical and abrasive substances during improper care for the product;
– making corrections to the text of the warranty card;
– the RCD (residual current device) is not installed, if there is electrical equipment on the bathtub;
– use of the product for business activities.
The company does not assume responsibility for damage caused during transportation and delivery.
Warranty service does not include reimbursement of installation and disassembly costs.
- Video instructions for assembling the frame of an acrylic bathtub Bas
