In the arsenal of every pastry chef there should be a rotary for cakes.

With it, you can greatly facilitate the process of decorating cakes and make it pleasant, comfortable and safe.

If the purchase is not planned in the near future, then an experienced craftsman can assemble it on his own.

If you want the cake to be accessible to you from all sides at the same time, and at the same time you would not have to run around it, be sure to consider having a rotating stand.

What is a turntable for cakes? This product is made up of:

• round working surface;
• – grounds;
• rollers, rubber bands

Thanks to its design, the table easily rotates around its axis, and provides convenient access to the confectionery product. With such a supply, you can create elegant and original decors and create decorations of any complexity. At the same time, you don’t have to worry at all that your masterpiece will move out, get damaged or fall to the floor.

The cake turntable can be purchased from ready-made and do it on your own. Homemade design has a lot of advantages. First, you can make a product that will fully meet your requirements and preferences. Secondly, you yourself will be able to create a well-thought-out drawing of the product, select the materials for its manufacture and think over the most optimal dimensions. Besides, homemade construction will be much cheaper than store bought.

materials

A swivel table can be made from any improvised materials:

Each individual option has its own advantages. The tree is environmentally friendly, safe, pleasant to the touch texture. MDF and plywood are easy to process. Besides, given material has a low cost.

But chipboard is inexpensive, and its appearance is attractive, and it is pleasant to work with it.

Advice: in order to save Supplies, for the manufacture of countertops, you can use the door from the old kitchen set.

Tools

Having decided to make a DIY turntable for cakes, prepare the following: tools and materials:

Important: bearings are double and pressed. The second option is preferable when assembling a rotating cake stand, as they are easier to install.

How to make a turntable?

Making a turntable is quite easy and simple. First you need to make a well-thought-out sketch. On this drawing, indicate the design of the product, its exact dimensions and materials of manufacture. With such a scheme at hand, you can easily assemble a table the first time and without errors.

Manufacturing process turntable carried out in the following sequence:

That's the whole simple process of manufacturing a rotating structure.

Advice: to give the product a decorative appearance, it can be pasted over with thin plastic.

Also, the product can be decorated with a self-adhesive film. It just sticks on and is easy to wash.

Photo

By choosing various materials and approaching the issue creatively, you can get very different tables.

The swivel cake stand is an essential tool for pastry chefs: from beginners to real masters. If you want your cake to be reachable from all directions at the same time, but without the need to “cut circles around it”, by all means consider having a rotating cake tray. Only he will help to make the cream decoration even. And the process of decorating itself turns into a bewitchingly beautiful action.

The swivel cake stand is an essential tool for pastry chefs: from beginners to real masters.

Such rotating coasters for decorating a cake look great at a large feast, on the windows of cafeterias or pastry shops. If you want to present a masterpiece made by yourself in the most attractive way, it is quite possible to use a rotating cake stand for this.

The product consists of:

• Round work surface;
• Bases in the form of a leg;
• rubber bands;
• rollers.

The design is designed so that the tray (stand) rotates freely around the axis. Thanks to this, access to the cake from all sides becomes convenient. Some variants are made with an inclination, so it is possible that the device bends at different angles. It is these designs that are most convenient when decorating desserts and when demonstrating sweet masterpieces. Such a stand allows you to create original decoration and form any decoration with maximum convenience. Moreover, the confectioner can absolutely not worry that his product will be damaged, move out or even fall.

The tilt stand allows you to create original decorations and shape any decorations with maximum convenience.

Types of rotating platforms for cake

In specialized markets, there are many coasters-trays of world famous brands.

Someone wants to have compact products for a dessert bar (Candy bar) when serving sweets. Some people like swivel models with an inclination, others will not be able to use only 2 tiers of the stand.

In specialized markets, there are many coasters-trays of world famous brands.

Varieties of design

There are such models, according to the form:

• Oval;
• Circle;
• Square;
• Rectangle.

As well as figured trays for an extravagant demonstration of confectionery creativity.

The turntable is often equipped with complementary accessories: it can be supplied “accompanied” by a spatula, lid, baking dish, pastry syringe, etc.

The rotary cake maker is often equipped with complementary accessories.

Materials from which the rotating cake stand is made

Cake racks are:

• steel;
• Glass;
• plastic;
• Ceramic;
• Wooden.

Rotating plastic cake stands are a rather fragile product. This is the most affordable option. Thanks to the last circumstance and the most common. They are presented in a wide model range are made with or without slope. Plastic cake makers usually have a non-slip material, which helps them grip well on the table. This is very convenient.

Plastic cake makers usually have a non-slip material, which helps them grip well on the table.

The glass spinning cake tray looks elegant. It is made of tempered high-quality glass, often decorated with an original pattern. It looks neat, spectacular - you can take a photo and serve on a rotating plate. Has a non-porous surface, quickly and easily washes, does not absorb odors.

The glass spinning cake tray looks elegant.

Metal constructions heavy, but they are designed for a longer service life. They can withstand weighty cakes, do not deform over time.

Metal structures are heavy, but they are designed for a longer service life.

The wooden cake stand is constructed from natural material looks aesthetically pleasing. Sweet products can be served directly on it. Cost compared to plastic stand rotating for decorating cakes, above.

The optimal diameter of wooden structures is at least 34 cm. Such a cake rack is roomy, it is convenient to decorate products from three kilograms (or tiered) on it and make confectionery decor on them. The wide surface makes it possible to place the leveling spatula in a convenient way.

A wooden tray has some advantages:

• He is durable;
• Does not absorb odors and moisture;
• It's easy to care for and easy to clean.

What is important - it "fits" into any interior.

The wooden cake stand is constructed from natural material and looks aesthetically pleasing.

The main criteria for choosing

When planning to purchase a kitchen attribute, pay attention to:

• Reliability;
• The quality of the material (it must be hypoallergenic and hygienic);
• Persistence.

Decide on the shape of the baked product, focus on the appropriate diameter. The wider the plate, the more convenient it is for the pastry chef to act. In specialized markets, you can find models with a width of 10 to 40 cm. Many consider the diameter 28 - 30 cm to be optimal.

Don't forget about the stability of the turntable. This is an important selection criterion.

When choosing a rotating cake platform, check if it has markings. This is a great help when decorating: decor elements can be distributed at the required angles, and the edges of the cake can be made as even as possible.

It is worth paying attention to the possibility of disassembling the structure: if the bearing breaks in the rotational mechanism, the non-collapsible stand will have to be thrown away. In such a situation, it does not stop functioning, but simply does not rotate normally. When you run a spatula along the side of the cake, it only twitches occasionally. This prevents the complete design of the product.

When choosing a rotating cake platform, check if it has markings.

Often, for most confectioners, the decisive condition for the purchase of such a cake maker is the presence of a transparent coating. It is ideal for serving purposes.

Popular with experienced craftsmen and additional mesh. It often comes as an accessory to a swivel stand. With this accessory it is convenient to cut cakes into beautiful pieces. It ensures accuracy in work: impeccable lines, symmetry, a layer of mastic or glaze after cutting is not smeared.

It is useful to buy a rotating platform on a leg for decorating cakes because today it is the most convenient inventory for decorating and subsequent presentations of sweet products.

The swivel tray is useful for banquet events and as a "showcase" for restaurants, cafes, pastry shops Can be purchased as an inexpensive plastic product, and a six-tier stand.

The swivel tray is useful for banquet events and as a "showcase" for restaurants, cafes, pastry shops.

How to make your own spinning cake stand

A turntable cake stand can be bought ready-made or assembled on your own if it is not planned to be purchased in the near future. homemade device has many advantages:

1. You yourself are free to create a drawing of the product, think in detail what dimensions will be the most optimal.
2. You will be able to create a cake that will fully meet your desires and preferences.
3. A self-made design will cost less than purchased in a store.

You will be able to create a cake that will fully meet your desires and preferences.

Materials for manufacturing

A spinning platform can be made from the following improvised materials:

• Plywood;
• Tree;

Each option has its own advantages:

• Plywood and MDF are easy to process;
• It is safe to work with wood, the material is environmentally friendly, the texture is pleasant to the touch;
• Chipboard is inexpensive, has an attractive appearance, and work with it is pleasant.

Chipboard is inexpensive, has an attractive appearance, and work with it is pleasant.

Required tools for making

You will need the following:

• Bearings (you can buy them at any auto shop; they are pressed and double; the first option is preferable because they are easy to install);
• self-tapping screws;
• metal circle;
• Nails;
• plastic tubes;
• Lumber (in this case, plywood).

Required Tools for the manufacture of.

Manufacturing process

Think carefully about the sketch before you start work. Indicate on the drawing the design of the product, what are its exact dimensions, what are you going to manufacture from. With such a scheme at hand, you can assemble a rotating platform easily and without errors.

Subsequence:

1. From plywood we cut out a round countertop according to the drawing.
2. Next, take the bearing (if not pressed, but double, hammer the smaller one into the larger one with nails).
3. IN wooden base cut 2 circles (d 20 cm).
4. Insert the bearing into the circle prepared in advance.
5. Using self-tapping screws, twist both parts together, place the bearing in the center.
6. The turntable is equipped with plastic pipes. They should connect the top and bottom of the future tortoise. It is better to make a tube at least 15 cm long (to simplify the process of decorating baked products: in this case, you do not need to lean over the culinary masterpiece being made).
7. The top of the turntable is made of metal. Ideally the diameter metal surface 30-40 cm.
8. The elements are welded together. If you use welding machine you don't know how to apply cold welding. The rotating part is installed on the pipe, the elements are fastened with self-tapping screws.

Your design is ready.

In order for the rotating cake stand to acquire a decorative appearance, it should be pasted over with thin plastic. You can decorate the product with a self-adhesive film. Sticking it is not difficult, it is easy to clean.

If you approach the issue of making a rotating cake stand creatively, you can get different trays.

If you approach the issue of making a rotating cake stand creatively, you can get different trays. The main thing is to clearly align the drawing and select high-quality materials.

Video: Making a do-it-yourself swivel stand

Turntable

Built a revolving table. Suitable for decorating cakes and for modeling (including dolls - heads). She blinded him, as they say, from what was. But it spins excellently (so far without a cake), at least play in the Field of Miracles or open a casino! :)

What I needed:

1) a hot stand (a round rug with a ball pattern - bought at a sale in the Metro store for 3 UAH), diameter 38 cm;

2) a piece of fiberboard (from it we cut a circle with a diameter of 1 cm less than a hot stand -37 cm);

3) a wheel for furniture on bearings and fastened with a screw and a nut (to make it easier to disassemble) - I bought it on the market for 12 UAH;

4) 4 screws, 4 nuts and 4 washers , so the hat should be flat);

5) 4 self-tapping screws 5-6 cm long;

7) drill and drill for self-tapping screws and drill large diameter to deepen the hole for recessing the screw head;

8) a block of wood about 60 cm long (I don’t know the exact size, it’s better to choose a specific wheel so that it is a little wider than the distance between the wings of the wheel base (to fit tightly)

9) sandpaper in order to clean the edges of fiberboard;

10) screw and wing nut, size 6, suitable length (cm 5-6);

11) glue "Dragon"

First of all, you need to cut a circle of the desired diameter from the fiberboard. Make 4 holes from the center (attaching the base of the wheel). The edges of the fiberboard need to be sanded and glued with tape.

Then we put the base of the wheel on a piece of timber (we grind it a little so that it fits perfectly), mark and drill a hole for the mount.

We attach the base of the wheel to our countertop.

TO wooden block we attach additional parts from a bar (so that the table is stable), fasten it to self-tapping screws.

We connect the upper part to the base and fasten it.

On the countertop we apply spiral glue "Dragon" from the edges to the center. We apply our rug - a hot stand and separate it again, wait a couple of minutes for the glue to thicken and again apply it to the countertop. Turn the table upside down and, gently pressing, iron the tabletop with your hand. reverse side so that the glue sticks well.

All is ready!

If there is a desire, then the leg of the table can be somehow decorated - painted, decoupled, etc.

There is such a thing as a turntable. Some use it for presentations, any souvenirs. Confectioners are used to rotate the cake during the manufacture of the latter. I decided to make a turntable with my own hands to show my homemade products, such as in "3D". The motor was taken as a basis microwave oven. Makes almost 3 revolutions per minute. It is powered by a 220V household network.

For the design of the table we need:
- a circle of plywood;
- plywood rectangle;
- switch;
- aluminum corner, for mounting the switch;
- network cord;
- screws 10 pieces;
- Microwave motor.

The first step in our base is making a cut under the motor. It turned out somehow crooked, but that’s not the point, it will be closed by the table itself. Base dimensions 250mm*100mm, plywood thickness 18mm.

We drill a hole with a diameter of 6 mm in the pancake of the table, the axis of the motor is 6.5 mm. The hole is not through, but exactly the length of the axis of the motor (about 10 mm). Trying on. Comes in tight. If you drill the same diameter as the axis of the motor, then the table pancake will hang out. It will have to be glued, and this is additional time for making homemade products.

Be sure to look at the motor. They are not 220V. I got 21V. In the latter case, a transformer is needed, it can be powered from the control board of the same furnace.

Since I have plywood BU, I decided to paint the pancake and the base of the table from a spray can. Matte black paint was available. Everything dried quickly. Along the way, I drilled a hole for threading wires.

After the paint has dried, we fasten the motor to its permanent place. I took the screws from an old printer. Very successful because of the wide hat.

We pass the wires into the hole from the side of the bottom of the structure. We unsolder the switch, I have a toggle switch TP 1-2. We attach the corner to the base. We fasten the toggle switch to the corner. If there is no corner like mine and another switch, then you can make something for your needs.

So that the design does not go around the table, I decided to install rubber legs. I used medicine caps as legs. In general, it is very convenient to use such legs in the manufacture of cases, homemade products. Rubber is very flexible. I screwed them onto all the same screws from the printer.

Pancake table in my case 230 mm. The thickness is the same 18 mm as at the base. Fits perfectly for my needs. This is the table I got. I repeat, it makes almost 3 revolutions per minute.

2692 0 0

How to make a turntable: construction and design choices, plus simple assembly instructions

Rotating tables are furniture that is in demand in various fields, from the advertising business to metalworking. But this time you will learn how to make an easy-to-use turntable for everyday use. I bring to your attention a simple assembly instruction, plus recommendations for choosing the right design.

Select turntables

Illustrations	Types of furniture and their description
	Classic turntables. In this design, the turntable is mounted on a vertical support. Due to the presence of a bearing, the rotary part of the furniture rotates around the support by 360 degrees.
	Iconic Turntables. Such devices are used by professional photographers or videographers to capture various objects from different angles. The photo shows a small homemade table with a small diameter of the rotating surface.
	Glass rotating podiums. These structures are used to demonstrate jewelry and other small-sized products that need to be shown favorably from different angles.
	Wooden rotating podiums. These are massive dining tables of a round shape, in the center of which there is a swivel structure made in the form of a tray. The design is used during banquets and other events where it is customary to serve dishes beautifully. The presence of a rotary part is designed to facilitate access to dishes from anywhere on the table.
	Kinetic rotating podiums. The design is based on two combined transparent surfaces, on which certain ornaments are applied. When the position of transparent surfaces is changed, the ornaments are superimposed on each other in different ways, creating certain patterns, due to which a special visual effect is achieved, as shown in the photo.
	Automotive podiums. In fact, these are all the same countertops, fixed on a movable support. The surface of the podium is driven by an electric motor with a reduction gear. Given the weight of the exhibits, the design of the turntable is assembled from rolled metal and made as strong as possible.

Which of the following structures to choose for self assembly? If the furniture is made for domestic use, we prefer the usual wooden structure, where in the center of the round dining table turntable installed.

Choose a tabletop project with a rotating center

The drawing shows a classic wooden table on a vertical support. A tray on a bearing is installed in the center of the tabletop. The dimensions indicated on the drawing are selected taking into account the comfortable accommodation of four people. In the assembly instructions, we will be guided by these dimensions.

The drawing shows a swivel assembly where the rotation of the tray is carried out thanks to a ball bearing. On the one hand, such a unit ensures smooth rotation of the tray, and on the other hand, guarantees a long service life of the entire structure. However, the design of the assembly can be simplified without compromising the smoothness of rotation by removing the ball bearing.

DIY: what to collect

Let's say you have an ordinary, unremarkable round wooden table, but you want more comfortable dining furniture with a swivel center section for comfortable access to dishes. I propose simple instructions assembly and installation of the very rotary part, turning which, this or that dish will be easy to get from any place at the table.

The assembly instructions in this article are for round tables with a diameter of 1-1.2 m. And what if there is no such furniture initially?

The instructions in the article are a guide to assembling a small countertop. Therefore, simply increase the proposed dimensions and, in addition to the turning part, assemble the main tabletop from the same boards.

Select materials

• Board 70×25 mm.
• Wood screws 30×5.
• Joiner's glue.
• Paintwork materials for finishing works.
• Rolling bearing (as an option, you can do it yourself, as described in the instructions).

Select instruments

For work we use the following:

• Electric jigsaw.
• Screwdriver with bits and drills.
• Big circle.
• Clamps.
• Pencil and ruler.
• Painting tool.

Assemble a turntable with your own hands

Illustrations	Make and install a turntable - step by step instructions
	Make a template. On old wallpaper or on waste cardboard draw a circle with a diameter of 550 mm. Cut out the circle according to the markup made earlier. If there is no compass, a rope will help to draw a circle. We tie a nail to one end of the rope, and a pencil to the other at the required distance. We put the nail in the center and draw a line with a pencil.
	Break the template into segments. We fold the paper circle in half, and then three more times to get 8 identical wedges.
	Make an insert template. We measure 3 cm from the extreme point of the circle along the fold line. We connect the marked points and get the workpiece as in the photo.
	Cut out liners according to the template. We cut off one of the eight extreme fragments from the template, as shown in the photo. We attach the template to the board and draw around the contour. Cut out the part according to the markup. To perform a curved cut, we use an electric jigsaw. As a result, we make 8 identical blanks.
	Sand the liners. Smoothing out bumps sandpaper and clean the workpieces from dust.
	Make the base of the circle. We fold the previously prepared 8 parts and glue them end to end. In order to obtain an acceptable quality of gluing, we place the parts on a flat surface. From plywood 4 mm thick we cut out a circle with a diameter of 530 mm. We glue the plywood circle on top of the hoop glued from wooden fragments. After the glue has completely dried, turn the circle upside down and remove the influx of glue from under the planks.
	Fill in the base of the circle. We alternately apply the boards to the notch of the circle and cut them so that they stand close to the side along the edge. We glue the boards prepared in this way into the recess and place them under the load for the drying time.
	Lacquer. We cover the finished tray with varnish or other paintwork materials that match the design of the table.
	Set turntable. We attach the outer ring of the plain bearing to the main tabletop. We attach the mating part of the bearing to the bottom of the tray. We insert the tray into the bearing on the countertop, after applying grease.

Explanation to the instructions: how to make a plain bearing? In order for the turntable to rotate freely without swaying, you need a bearing that you can do yourself.

The diagram shows a simple plain bearing consisting of two rings - an outer and an inner ring or cylinder. Both structural element fastened to the corresponding sides of the combined tabletops.

The gap between the outer and inner ring in order to avoid play should be no more than 1-2 mm. One ring is attached to one countertop, the other to the other.

Perhaps the assembled assembly will not be as comfortable as a ball bearing when scrolling, but given the speed of rotation of the turntable, this is not so important.

Calculate the labor costs and cost of making a table with a rotating center with your own hands

Which is cheaper - buying a table with a rotary center or independent production such furniture? Of course, it's cheaper to do everything yourself. Let's try to calculate how much it will cost to manufacture a turntable, described in the instructions.

You will need a board 70 × 25 mm, length 4 m, which costs an average of 130 rubles. Plus, you need self-tapping screws in the amount of 20 pieces, which will cost 20 rubles. In total, the materials will cost 150 rubles, and to this we add a little wood glue and varnish with a stain from a home workshop.

As for labor costs, they are quite comparable with the assembly of a conventional dining table. If you make only a turntable to an already finished table, everything about everything will take no more than one free day.

Conclusion

Now you know what revolving tables are, how they are arranged and how to make them yourself from available materials. If you have any questions, write about it in the comments and do not forget to watch the video in this article.

November 24, 2018

If you want to express gratitude, add a clarification or objection, ask the author something - add a comment or say thanks!