Modern industry has presented the owners of apartments and houses with high-quality balcony doors made of metal-plastic profiles.
These near-perfect products fill openings en masse as users find them ideal for use. But they are also subject to various factors, due to which balcony doors must be adjusted for perfect operation.
One of the common problems with plastic balcony doors is sag. This is expressed in the formation of gaps between the canvas and the upper part of the block box.
The cause of this problem is the large mass of the double-glazed window, which presses on the door leaf during opening or being in the open position.
Also, such a nuisance can occur due to errors by installers who incorrectly set the unit during installation.
To adjust the door in this situation, you can use a hex key, which will have to turn the adjusting screw on the lower and upper hinges mounted on the box.
But first you need to free them from the decorative overlays that cover the mechanism. This is quite easy to do, as they are easily removed from the hinges.
It is worth noting that both hinges must be adjusted equally so that the load on them is distributed evenly. After checking the work of the canvas, you can install the lining back.
Another common problem with plastic balcony doors is grazing the vertical profile of the frame.
This offset can be corrected using the same hex wrench, unless, of course, a screw with a different head, for example, with a star, is installed as a fastener.
Unlike vertical shift, you need to rotate the screws on the hinges that are installed on the door leaf itself.
Depending on the direction of displacement, you need to rotate the key clockwise or counterclockwise. In this case, it is required to ensure that the sash is in a strictly vertical position and the resulting gap is the same along the entire length. You can check this by eye, but it is better to have the following tool on hand:
- Building level or plumb;
- Ruler.
It does not hurt to stock up on a tape measure to measure the diagonals of the box. There are cases when the balcony block is exhibited in violation of technology.
In normal working condition plastic doors tightly pressed against the box profile, creating a sealed vestibule. But over time, it ceases to be such and a draft appears.
You can check the web pressure with plain sheet paper. It should not penetrate the rubber seal when trying to push it between the sash and the frame.
You can adjust the clamp with the help of trunnions, evenly spaced along the entire web. They are small cylinders that are opposite the clamping bars mounted on the box. When you turn the handle, these elements cling to them and tightly pull the door.
Each trunnion has a risk, which marks the position of the clamping mechanism. By turning the cylinder to the right or to the left, they are shifted relative to the vertical axis. So you can make the clamp stronger or slightly weaker, if necessary.
But sometimes it is not possible to adjust the density of the sash attraction only due to the trunnion, since the canvas has sagged a little, although it does not draw on the box.
In this case, you can move a little clamping bar, for which the cylinder clings and the operation of the mechanism will become more efficient.
It should be remembered that you need to adjust all the trunnions installed on the canvas. This is the only way to achieve high-quality clamping.
It is not always possible to adjust the position of the canvas with only one loop. Sometimes it is necessary to displace the double-glazed window itself, which, if installed incorrectly, creates an uneven load on the balcony door. In this case, you will need:
- Thin chisel or hard metal spatula;
- Rubber mallet;
- Ruler.
First you need to remove the layout that fixes the double-glazed window in the door leaf. After that, you need to carefully adjust its position, if necessary, placing plastic linings.
Correctness must be checked with a ruler. The distance on all sides should be the same. Then the double-glazed window is again fixed with a layout, which is carefully inserted into place and knocked out with a rubber mallet.
Attention and accuracy
You can make adjustments to the balcony door yourself. At the same time, the process itself can take place without the help of an assistant, since it is not necessary to remove the canvas from the hinges.
But do not forget that any work must be carried out very carefully, otherwise it can lead to damage to the mechanisms. And if this happened, then it will not be possible to do without a replacement.
In order not to bring the door to complete wear and tear, you need to pay attention to its work.
If somewhere it starts to touch the profile or when closing the sash does not move to the box, pressing tightly, then it is better not to waste time and immediately make adjustments. The rest can be done by a simple home master.
Also look at the video examples of adjusting the accessories of the balcony door:
Plastic steel doors worthy alternative wooden and in external design, and in cost, and in wear resistance. To ensure high durability, it should be remembered that any mechanism needs periodic adjustment, so adjusting plastic doors is a mandatory procedure. Next, we will analyze in detail how to adjust the plastic door yourself, using a minimal set of tools.
Adjusting a plastic door is a very real task.
Before adjusting the doors with your own hands, study the documents for the purchased product. Firstly, there may be detailed instructions for setting up this particular model, and secondly, you should make sure that the warranty has already come out, because if the door is under warranty, then one call is enough and it will be set up for you.
Setting up entrance and interior plastic doors with your own hands differs from adjusting plastic doors. balcony structures. This is due to several reasons:
- Plastic thickness and profile configuration for balcony and interior doors different. By the way, the design of the entrance and interior doors is almost the same, so the adjustment of the plastic entrance door is carried out in the same way as the adjustment of the interior door.
- The adjustment of the entrance plastic doors is mainly carried out by adjusting the hinges, and additional fittings and handles are involved in the adjustment of the balcony doors.
- The balcony door is often equipped with a folding ventilation mechanism, which is also adjustable, while its entrance and interior counterparts do not have a folding ventilation mechanism at all.
- How to adjust plastic doors is largely influenced by the weight of the structure. Often, a balcony door is almost half as light, which means there are fewer adjusting and locking screws in the design.
How to properly adjust a plastic balcony door is written in detail with examples and explanations. If your balcony plastic door is completely jammed, then there is information about the causes of the breakdown and how to repair it.
When to Adjust Doors
Any, even the most expensive and beautiful plastic door sooner or later needs to be adjusted. The need for periodic adjustment is caused by the following reasons:
- The building itself may sink. In this case, the box slightly warps.
- Problems may be caused by incorrect installation. Here errors will appear within a month. As a rule, the door closes tightly or poorly.
- Incorrect or intensive use. Often this requires adjustment of the loops and replacement of the seal.
- Doors can sag under their own weight. Here, the hinges are also tightened in height, plus sometimes it is necessary to adjust the pressure of the plastic door.
Before adjusting a plastic door, you need to diagnose it. This will give a clear understanding of which node needs to be configured.
First of all, take a look door leaf and a receiving box around the perimeter. Small abrasions indicate that the door has sagged. Immediately mark these places with a pencil.
If you notice that it began to seep through the doors, it means that somewhere along the perimeter of the canvas there is a gap. It is useless to examine the clamp with a lit candle in plastic doors, the flame will begin to fluctuate only in the case of a very large gap, while small gaps are covered with a sealant, and the candle does not react to them.
The sagging area can be identified with a sheet of paper. You need to insert a sheet of paper between the frame and the door leaf, then close the doors and try to pull the paper out. If the pressure is good, then the paper will sit tight, and if the pressure is poor, you will freely pull the sheet out. So the entire perimeter is examined.
It happens that the door clamp has absolutely nothing to do with it, just in some area the rubber seal is worn out or damaged. In this case, you must first replace the seal, and then check the clamp.
To identify the curvature of the door leaf horizontally and vertically, you need to completely close the doors and circle the canvas along the contour with a simple pencil. Then take a ruler and measure the distance from the drawn line to the edge of the box.
Vertically, you need to measure at three or four points, horizontally at two or three points. Although sometimes without measurements, with the naked eye you can see where the doors have shifted.
Not so often, but it still happens that the cause of problems with the doors is directly the locks, the reciprocal and locking strips of the locks, as well as the latches and the door closer. Therefore, we recommend that the door closer be disconnected first during diagnostics, and then check the lock group. If everything is in order there, then you can start checking according to the above scheme, that is, searching for scuffs, controlling the pressure with a paper sheet and outlining the outline of the canvas.
By the way, if you find out that the reason is in the door closer, then you can find information on setting it up.
Technique for adjusting various nodes in plastic doors
It is impossible to say unequivocally how to adjust a plastic front door, because many companies produce fittings, which means that its adjustment scheme may differ in each individual case. As already noted - if there are problems with closing entrance doors and the locks are in order, so you need to look at the hinges.
If doors are equipped with GreenteQ hinges
Regardless of which company made the hinges, in all such mechanisms, the adjustment of plastic doors can be independently performed in three directions:
- The door does not close tightly, that is, a clamp.
- Vertical - this is when the door needs to be raised or lowered.
- Horizontally - this is when you need to pull the canvas to the right or left.
door hinges from trademark Almost half of the existing plastic doors are equipped with GreenteQ. Plus many competitors just copy general principle operation of this mechanism, so we will focus on it.
To get to the control system, you first need to take out three plastic plugs: top, bottom and side.
Next, you need to remove the decorative trim itself. To do this, you need to open the door and unscrew the fixing screw, which is located from the inside of the hinge. In GreenteQ hinges, this screw is made for a Phillips screwdriver, there are also screws for a flat screwdriver and a thin hex.
The pressure on the GreenteQ hinges is adjusted by the top vertical eccentric. This mechanism is located on that part of the hinge, which is fixed on the door leaf.
You need to insert a 4 mm hexagon inside the eccentric, and then turn it clockwise or counterclockwise. By turning the hex, you can adjust the pressure by about 0.75 mm.
If a backlash of 0.75 mm does not suit you, for example, due to replacing the rubber seal with a thicker one, then you can replace the gasket under that part of the hinge that is attached to the box. These pads are for sale. The thickness goes from 1 to 5 mm, in 1 mm increments.
The gasket for the hinges can have a thickness of 1 to 5 mm.
Horizontally, the mechanism of this model is regulated by a side screw. The head of the screw was made for a 4 mm hexagon, and the screw itself is part of a horizontal structure. To adjust the hinge, you must first loosen the six mounting screws for a Phillips screwdriver. You should not completely unscrew the screws, just loosen them slightly so that the mechanism moves.
To adjust the door leaf vertically, tighten or loosen the bottom screw. It is noteworthy that the door, adjusted at the factory, lowers only 1 mm, and rises 4 mm. Such a paradox is caused by the fact that often the canvas needs to be lifted, as it sags under its own weight.
Plastic doors - vertical adjustment of the door leaf.
After all the settings, the plastic decorative trim is closed, the internal screw is screwed in to fix this trim, and the plugs are installed last.
Adjusting the hinges of the WX model
If the GreenteQ type hinges are placed on both interior and entrance plastic doors, then the WX model hinges are more designed for heavy street doors, and they are installed not only on plastic, but also on aluminum structures.
First, the decorative caps are removed from the bottom and top. They do not sit tightly to remove such a plug, it is enough to pry it with a knife.
From the inside, next to the cover latch, there is another locking screw for the hexagon. It fixes directly the mechanism responsible for adjusting the door leaf horizontally. It is not necessary to unscrew this screw completely, just release it.
As a rule, the decorative protective cover in these models is not completely removed, it only rises slightly. So, when you lift it up, you will find an adjusting screw on the side, with this screw the doors are adjusted.
Turning the screw will move the doors to the right or left. The maximum stroke here is about 3 mm.
In the hinges of the WX model, the pressure can still be adjusted. The mechanism itself is located in the second, mating part of the structure. To see it, you must first remove the cap. After that, also open the door and release the locking screw from the inside of the hinge.
This mechanism has another fixing plug. It is installed on top and made under the hexagon. This plug is unscrewed and removed completely.
Now it's time to adjust the pressure. To do this, a key or some device of a suitable size is inserted into special grooves, and the mechanism turns. The key stroke is about 90º, the pressure value is +/- 1 mm.
Do not forget that the mechanisms are "gentle". After adjustment, they must be closed and the locking screws must be tightened. Closing is done in reverse order.
A few words about replacing the seal
In this case, the good news is that the window and door seals are almost the same, and most importantly, the principle of replacement is no different for them. Manufacturers promise that the door seal can last 5–7 years, but according to experienced craftsmen, the maximum for a rubber seal on doors does not exceed 2–3 years.
Remember, any plastic construction is equipped with several sealing circuits, and the configuration of each of these circuits is different, so it is advisable to take a complete set.
Example of a three-circuit seal for a plastic construction.
It is impossible to adjust the seal, to some extent you can extend its life by lubricating it with silicone, but nothing more. If the rubber is worn out, then it only needs to be changed.
The replacement technology is extremely simple:
- Find the edge of the old seal and, prying it with something sharp, pull it out of the grooves.
- Then, with a knife or a thin screwdriver, clean the remnants of glue and rubber from the groove.
- After that, push the tongue of the new seal into the groove around the entire perimeter with the same screwdriver or something similar.
- So that the seal does not turn out of the groove during operation, it sits on the glue, but you need to act without fanaticism, we drip glue pointwise, in increments of 50–100 mm, otherwise you will get tired of cleaning the grooves the next time you replace it.
Conclusion
If you figure it out, then adjusting the entrance or interior plastic door through the hinges will not be great work. This is much easier than setting up balcony or window fittings. Adjustment of other types of doors with detailed photos and video you can find.
Before each user plastic products, after a long time of operation, a dilemma arises - how to adjust the plastic door? No matter how high the quality characteristics of the door and its components, which are designed to ensure the closing and opening of the PVC sash, after a certain time the mechanism, one way or another, will need to be adjusted.
If it is necessary to regulate a PVC door, it would be more rational to contact the relevant specialists, in particular, those who carried out its installation. But, unfortunately, such an opportunity is not always available, nevertheless, and the departure of the master is unlikely to be carried out on the day of the call.
In addition, mastering the skill on your own is not at all difficult, since the process of adjusting a plastic door is not something supernatural. Moreover, customizing plastic products is never a frequent procedure. Adjusting a plastic door is relevant only if you have a complaint about the functioning of the door.
The installation of a new plastic door also includes adjustment work, which is performed immediately, and for a long time after, the design should not cause unnecessary questions. But after a period of active use, the product will still need to adjust the mechanism, as a result of sagging, poor pressure or the inability to close the door.
Despite the excellent quality and confidence of the door installation company, it is recommended to personally observe the adjustment process to make sure that the plastic doors are adjusted correctly.
Upon completion of the work related to the establishment of the hinges of the plastic structure, pay attention to the following points:
- the frame should be pressed tightly against the box around the perimeter;
- opening and closing the door should be easy, without additional effort, without squeaks;
- use building level to check the verticality of the door;
- check the arbitrary opening and closing of the sash. To do this, you need to open the door halfway, when checking to exclude the effects of wind and draft.
Frequent damage to the plastic door
The most common product defects are:
- Touching the lower edge of the sash with a part of the frame that functions as a threshold. This occurs as a result of the sliding of the sash under the action of its own weight;
- Cloth touching the middle of the frame. The basis for this is the direct shifting of the sash under the influence of various deformations, as well as temperature;
- Poor clamping of the sash to the frame, as a result of wear of the seal;
- Staggering and falling out of the socket of the door handle.
Initially, it may seem that adjusting a plastic door is a complicated procedure based on options. possible faults. But in fact, you just need to understand which mechanism needs to be tuned, and the instructions below will help you in troubleshooting your own problems associated with a plastic product.
Plastic structure adjustment
Before you start building a PVC door with your own hands, stock up on screwdrivers (regular, flat and Phillips), hex keys different size, gaskets.
Good instructions and necessary tools will allow you to correctly complete the entire cycle with your own hands, and as a result, the adjustment of plastic doors will be successfully and safely performed.
Eliminate sagging sash
To eliminate such a breakdown, you should direct the canvas up and slightly move it towards the loop, which is higher. Open the sash, and with a hex key (4 mm), turn the screw on the end of the sash at the top, at the location of the hinges.
To move the sash, make about 1-2 turns in a clockwise direction. After that, close the sash and remove the protective cap from the hinges arranged below. Turn the screw on the upper hinges, slightly lifting the canvas. If the sash easily "walks", then the problem is solved.
Pressure control
Schemes for setting up hinges on a plastic door.
To adjust the clamping of the web to the frame, it is necessary to use a locking element. It is located inside the sash, and acts as eccentrics. The pins are adjusted with a special key and pliers.
Do-it-yourself pressure adjustment is carried out in the summer and winter periods, this is enough for the normal operation of the product. In winter, you should independently adjust a tighter and stronger pressure than in summer. It is necessary to press the sash to the frame from the side of the hinges by means of adjusting screws.
Horizontal setting
Correction of the operation of the plastic construction hinges can be carried out both in vertical and horizontal directions. For horizontal adjustment, first remove the door from the hinges at the top.
Then close it and lift the caps that hide the adjustment screws. To avoid skewing the product, tighten the long screw in the place of the upper hinges slightly with more force than at the bottom. To ensure the same shift of the sash, remove the trim from the hinges and tighten it by loosening the screws horizontally located in the door hinges.
Vertical looping
If it is necessary to raise or lower the product, adjust the mechanism vertically. There is an adjusting screw along the axis of the bottom hinge. To adjust the entrance plastic doors, a hex screwdriver (5 mm) is useful.
By turning the tool, the door can be lifted slightly, and by turning the screwdriver in reverse side- the structure will be omitted.
How to avoid frequent adjustments?
It will not be possible to completely get rid of door adjustment, but it is quite possible to make it less frequent. When purchasing a double-glazed window, take care of the fit of the fittings and the weight of the canvas.
The optimal weight of the sash is 100-130 kilograms.
Sagging of the structure under its own weight can be eliminated by mounting auxiliary element fittings, which is called a sag compensator, better known as a "microlift".
Such a detail is simply necessary for the product, especially in the presence of a double-glazed window with impressive design dimensions. And if you correctly install the support rail with your own hands - the opening limiter, you can easily avoid jamming and sagging of the structure.
As you can see, adjusting a plastic door is not very difficult, if desired.
Sections of the article:
Adjusting plastic doors is a process that is designed to eliminate all sorts of problems that have arisen during the use of the structure. No matter how expensive the door and its components are, items always break, especially those that are used frequently.
Most often, door adjustment is required, for the reason that the hinges can weaken and become loose. As a result, the door is uneven, and a draft is blowing from the cracks that have opened. The root cause of the breakdown is the wear of individual parts, but their quality also plays a significant role. That is why you should not save on quality, so that in the future you do not have to think about adjusting the plastic door.
If you have problems with a plastic door, but you don’t want to contact the masters, you can fix the breakdown yourself. But for this you need to prepare and find out the answers to the following questions:
- In what place of the door are the parts intended for adjustment;
- What problems can generally arise with plastic doors and how to solve them;
- How exactly is the adjustment of the plastic door.
What is responsible for regulation
To adjust the door, you will need a hexagon with a diameter of 4 millimeters (most often), sometimes pliers will be useful.
The first adjustment node can be found on the bottom door hinge By turning it with a hexagon, you can raise or lower the door, depending on the direction of rotation.
Required tool. Here you can also find a node that shifts the lower part of the door to the right or left. Sometimes the adjusting screws are covered with protective caps that are easy to find and remove. To move the top of the door to the left or right, turn the screw located at the top hinge.
The clamping force of the door to the door frame is regulated by eccentrics, which can be found throughout the door body. By twisting them, you can achieve precise adjustment of plastic doors and their tightness by changing the pressure in certain areas. Tilt and turn doors have a way to adjust the pressure of the entire upper part. To do this, turn the screw located at the top of the door.
Getting to this screw is not easy enough, you need to put the door immediately in the ventilation mode and in the “wide open” mode. A built-in mechanism that can be bypassed protects against such opening. It is enough just to open the door, align the plate, which is located on the end of the door at the handle (parallel to the rubber seal) and turn the door handle to the ventilation mode. This is a rather complicated procedure, so in order to know exactly how to adjust a plastic door in this mode, we recommend that you familiarize yourself with the video.
Ways to adjust for different problems
To correct the shortcomings, you need to know which screw is responsible for what, and for what problems to turn it.
This is due to the complexity of the door design and the abundance of all kinds of screws, the incorrect torsion of which can lead to a complete breakdown of the mechanism.
Upon request, adjusting plastic doors, you can find a lot of videos from professional craftsmen that will help in the work.
Sagging
Over time, the entrance protection sags under its own weight, and due to the fact that it is mounted in the air. This is one of the most common problems and at the same time unpleasant, because in this case the lower profile rubs against the frame, and in difficult cases the door becomes difficult to close. In this case, we will definitely have to take care of adjusting the plastic door until the situation worsens.
Skewed and sagging doors. To fix this problem, you need to lift the door up. This can be done using a special hole in the middle of the bottom loop. By inserting and turning the hexagon clockwise, we will raise the door higher. If you need to lower the door, you will have to turn it counterclockwise.
In the event that the frame is touched only by the part of the door opposite the hinges, horizontal adjustment of the upper hinge will help. By inserting the tool into the hole and turning clockwise, we will pull the upper section of the door closer to the frame.
Top hinge adjustment. Adjustment of plastic doors from sagging can be carried out independently, but to know the purpose of all screws and connectors, you need instructions from the manufacturer.
Friction on the box
If the door rubs against the box when closing and opening, you need to know how to adjust the mechanism by moving the plastic doors to the left or right.
Bad pressure
If a draft is blowing from your door, then the pressure of the door to the box has most likely weakened. This is corrected by adjusting the plastic door, namely the eccentrics. The mechanism of their work is that when closing, the eccentric climbs behind the pressure plate.
Plastic door eccentrics. From this it follows that in order to increase the pressure, it is necessary to rotate each of the connectors in exactly the same way. You should not assume that the stronger the twist, the more reliable the clamp; with extreme pressure, the sealant may dry out and stop doing its job. Masters recommend loosening the pressure in the summer to give the sealing gum a little freedom and provide a little extra ventilation in the house.
Complicated closure
Another common problem with plastic doors is that they require force to close. Most often, force is required to apply when turning the handle.
These symptoms are indicative of winter mode eccentrics, and to facilitate closing, you need to loosen the screws.
Before adjusting plastic doors, it is necessary to watch a training video in order to know the required tightening level.
Another cause of difficult closing can be a clogged door mechanism. In mild cases, full lubrication can be dispensed with, in difficult situations you will have to disassemble the door and clean the system.
If the door is used for a long time, the handle may loosen. To fix this problem, rotate the top plate of the handle base and tighten the bolts underneath.
Adjusting doors with GreenteQ hinge
If the door is heavy (more than 40 kg) and is frequently used, it is in most cases equipped with GreenteQ type hinges. Adjusting plastic doors, and especially on your own, can be a problem, so it is recommended to watch a video of the process before starting work. You can adjust them in three planes:
- Vertical;
- Horizontal;
- Attach to the box.
To access the hinges, you need to remove the plastic protection from them, which is quite easy to do. To raise or lower such a door, insert the hexagon into the slot located at the bottom of the hinge and adjust by twisting to one side. Remember that the adjustment of plastic doors begins with the lower hinge, and then the middle and upper ones are adjusted to it, which can be done independently.
To move the doors left and right, screw in or unscrew the screw located in each hinge under the decorative masking. 
To adjust the pressure level, insert the hex key from the top of the end of the hinge, and change the position of each of them in a circle. Now you know how to properly adjust displaced or weakened plastic doors using your own hands.
So, adjusting pvc doors is a simple process, but it requires care and perseverance when doing it yourself. Now you know how to adjust a plastic door without calling specialists at home.
For the winter, you need to not only insulate windows and walls, but also think about doors, whether they are entrance doors or even just balcony doors. The article contains instructions on how to identify problems with a plastic structure without a wizard and independently perform the necessary adjustment.
The main problems of the balcony door and their causes
As soon as specialists install a plastic door, they immediately regulate it. To make sure that the masters did their job in good faith, pay attention to the following points:
- The door frame is tightly pressed against the box in all places.
- The door opens effortlessly and also closes. If it creaks, it means that the work was done poorly.
- The design is not vertically offset. You can check this using the building level.
- The door doesn't sag. A simple test will help you check this. Taking a pencil, circle the closed canvas over the entire area, and then compare the resulting lines with the frame. If they are parallel, the adjustment work was carried out qualitatively.
- If the door, half open, remains motionless, it means that it is adjusted correctly.
Attention! Make sure that during this test there is no draft in the room, from which even a well-functioning door will close by itself.
Over time, the structure wears out, and then you need to do an additional correction. Most often it is required in such cases:
- Part of the lower shutter touches the threshold - a sign that the door sagged under its own weight. The bulk falls on the double-glazed window, so if it is double, then the hinges become weaker, and the sash moves.
- reeling door knob. This problem is the easiest to fix. Turn the plug at the base of the handle and tighten the screws with a screwdriver.
- The sash touches the frame in the center - this indicates that its side part has been displaced. This sometimes happens due to frequent temperature changes. Doors that lead to an unglazed balcony are especially affected by weather conditions.
- Loose door latch.
Advice. If the door requires additional adjustment, contact the company that installed the door. Do the work yourself only if the warranty period for the plastic structure has expired.
How to Diagnose Poor Clamping Density
The following signs indicate that adjustment is needed:
- The canvas is not pressed very well against the frame. It feels like air is escaping from under the seal.
- The door closes quite tight, you need to make more effort than usual.
Attention! If this defect is not eliminated, then in winter drafts will walk around the apartment.
The following experiment will help determine the need for regulation:
- Take a paper sheet.
- Place it between the frame and the door frame.
- Close the door tightly.
- Pull the sheet over the edge, remembering how easy it is for you.
- Repeat the procedure on all sections of the structure.
Advice. For self-adjustment of the plastic door mechanism, stock up on several types of screwdrivers, keys of different diameters with 6 edges, pliers and a set of gaskets.
Pressure adjustment instructions
- Adjust the tightness of the door by rotating the special parts - eccentrics with a key and pliers. They are located at the end of the canvas, usually in 3 places: at the top, in the center and at the bottom. You can see how these parts of the mechanism look in the video or photo.
- Rotate each eccentric a little, checking how much the pressure has changed. So you pick best option and adjust the density, but only in the area of the door handle.
- To ensure complete tightness of the plastic structure, make adjustments on the hinge side as well. To do this, turn every third adjusting screw both at the top and at the bottom. It is convenient to use a hex key for this purpose.
Advice. Engage in pressure adjustment twice a year, doing this in the summer and in the winter. When it's cold outside, make the fit tighter, and loosen it in warm weather. Leaving the "winter" setting for the summer is not recommended, since both the seal and the mechanism door block wear out much faster.
Adjusting the door if it sags
To eliminate this defect, you can not remove the door leaf from the hinges:
- Having opened the doors, on the upper canopy, find a screw that opens with a hex key or a special one - an “asterisk” (depending on the model of the plastic structure itself).
- Turn the screw a couple of turns to the right.
- If the sash still touches the threshold, remove the protective cap from the bottom hinge.
- Locate the adjusting screw and also turn a couple of times to the right.
If the door hits the frame in the middle, do the following:
- Use a wrench to turn the lower adjustment screw on the side inside. 2-3 turns are enough. So you move the sash to the hinge.
- If the door does not close well, repeat the procedure, but already on the upper canopy.
Horizontal adjustment. Step by step description
Sometimes it becomes necessary to adjust the position of the door, for example, move it slightly to the right or left. For this:
- Open the door and unscrew the screws from the upper canopies. Use a 6-point screwdriver.
- After closing the door, remove the lining, behind which are hidden screws for debugging the mechanism.
- Twist them: stronger in the upper loop, slightly weaker in the lower loop. So you do not allow the structure to skew.
- If you need to evenly move the door to the canopies or, conversely, away from them, remove the trim from the bottom hinge.
- Tighten it and slightly loosen all the screws that are located horizontally in the canopies.
Attention! By turning the screws clockwise, you will move the door to the hinges, by turning it counterclockwise, you will slightly move the leaf in the opposite direction. Thus, it is possible to correct the movement of the structure within 2 mm.
Vertical adjustment. briefing
If the door needs to be slightly lowered or raised, make a vertical debugging of the mechanism.
- Locate the adjustment screw at the bottom end of the canopy. It is located along the axis of the loop. Sometimes the screw is hidden by a plug that needs to be removed.
- Turn the adjusting screw to the right to raise the door and to the left to lower it. A hex screwdriver is again suitable for this, and a lift height variation of up to 2 mm is also possible.
Advice. To reduce the need to adjust the door so often, install an opening limiter and a micro-lift on it, which supports the canvas when it is closed and does not allow sagging.
