How to make a bottle stork. Do-it-yourself stork from plastic bottles - nothing complicated! Materials and tools for a garden figure

It is very easy to make a stork from plastic bottles with your own hands, a master class will allow you to complete this product in a short time. In this case, it is necessary to strictly follow all the instructions in order to get really good result. The product can be placed on a personal plot, which will make it possible to decorate the territory.

A master class allows you to make a stork on your own, for which you need to use plastic bottles and other improvised materials. To make the craft look the most realistic, it is necessary to make blanks from plywood. Wings and torso are drawn on them. Prepared templates must be carefully cut.

For work you will need the following materials:

plastic bottles;
insulating tape;
self-tapping screws.

It is better to take bottles that are opaque (white) and dark, and then arrange them, and only red is suitable for electrical tape.

Previously prepared templates need to be connected. To do this, you will need self-tapping screws. To make feathers, white bottles are used, in which dairy products are usually sold. They need to be cut so that strips of the same width are obtained. Along the edges, you need to make many shallow cuts to get a fringe.

The resulting wings are fixed on the body of the bird. To make the fastening as strong as possible, use glue gun. It must be applied carefully, without leaving traces of glue on the body. To make the tail and the rest of the body, which will be located below, you need to use dark plastic bottles. In such containers, for example, beer is sold.

The beak can be obtained from the blank of a plastic bottle, since the stork has a red beak, the base is wrapped with red tape. Need a stork and legs. For their manufacture, you can use a thick wire. For the eyes, take large beads, which are attached to the head with glue. On this, a stork for a garden with your own hands can be completed. It can be placed near a flower bed or on some kind of stand.

Details of the production of the second option

To make a talisman bird for the garden with your own hands, you should prepare the following materials and tools:

empty plastic bottles;
2 wooden beams: thick and wide (will serve as a base);
thick aluminum wire (you can use a rod) to make lower limbs;
polystyrene (thickness 10 cm);
corrugated hose;
plastic canister (2 pcs., capacity 5 l);
metal mesh (under the wings);
stapler.

How to make a stork with your own hands? The procedure will take a little time, but the algorithm of work is simple. On the paths personal plot or a stork will appear in the garden after a few hours of execution.

First you need to start making the head and beak of the bird. These parts are cut out of foam. On the surface, you can either draw eyes with black paint or glue 2 black buttons (you can use beads).

The beak itself must be cut out of a dark plastic bottle. It will consist of 2 parts, glued to the head. To get the body of a bird, you need to cut off the handle from the canister.

Bending tightly around the contour of the canister, bend the metal mesh. Remove excess material. You can perform the lower limbs if you bend the rod, the ends of which should be fixed in wooden block. Plastic feathers are cut from bottles. They are attached to the base of the canister. Attach the tail first.

You can plant the neck of a stork by fastening the wire to the armature. The next step is to put the prepared hose on the wire. Since the feathers on the neck should be small, they are attached with tape. Feathers along the body are fixed on a metal mesh.

Since the bird in the garden will be upright, its wings will be folded. They need to be fixed with a stapler. Feathers should be arranged so that the details of each subsequent row overlap the previous row by 1/3. This will give the craft naturalness and naturalness.

The master class ends with the fastening of individual elements. To give the product maximum attractiveness, you can perform decorative tinting of the beak, eyes, legs. The craft can stand on the street throughout the summer, it is not afraid of bad weather.

Alternative product

The original DIY stork for the garden can be complemented by a baby in the nest. The implementation of this option will help to make the home happy and bring prosperity and well-being to the house. For the manufacture of a stork sitting in a nest, patterns of the Tilda bird are used as the basis. It is quite modern and fashionable today. homemade toy from tissue matter. Patterns for her are simple.

Cut out of dense and durable fabric individual elements crafts. The pieces are sewn together with a thread. To give the body volume, you need to fill it with any filler, so you don’t need to completely stitch the bird right away. Burlap, sawdust, straw, feathers, unnecessary flaps, etc. can act as a filler. After completing the filling stage, the hole is completely sewn up.

The beak is made separately. To create it, you need a strong red cardboard. The finished part is attached to the already made head. You can sew clothes. To do this, you need to take measurements from the finished bird. At the final stage, the eyes are glued, the baby is wrapped in a light cloth and placed next to the mother.

If you install crafts on the branches of trees in the garden, when it rains, you need to remove it from there so that appearance product is not damaged. Another such bird is placed on the windowsills, it will be in perfect harmony with indoor flowers.

Based on a fabric stork, feathers are obtained from plastic bottles white color that sell milk or other dairy products. They are fastened together. Finally the wings come out.

Unusual option

Noteworthy is the master class on making a stork, which is based on a large plastic bottle with a volume of 6 liters. To make the head, you need to use foam, which will need to be carefully cut. Do not forget about the shape of the beak and eyes. Black pebbles can act as eyes, which are fixed with glue.

The beak can be made from an ordinary plastic bottle. It also sticks to the head. A large plastic bottle will act as the body. It needs to cut off the neck. Special metal mesh - wings. If the bird's wings are bent, it is necessary to make appropriate bends on the grid.

The legs are made of wire, which is folded in several layers. Feathers will be from light-colored plastic bottles. They are cut so that individual feathers look realistic. Fixing is done with a wire to the wings themselves.

To make the neck look voluminous, the bottles need to be finely chopped, you get a fringe. They are arranged in rows. Small bottles are put on the paws, which are also cut at the base. If the fixation of parts seems weak, then the fastening process can be carried out using self-tapping screws.

Making a stork is not a very long and difficult undertaking. To bring the idea to life, you can use the above recommendations. However, you can make certain adjustments to the idea that will allow you to create a unique and original product.

Bright garden crafts from plastic bottles - simple and affordable way decorate your favorite area. original sculpture a stork made of durable material will update the familiar landscape and create a joyful mood. A do-it-yourself bird figure will make the garden unique and become a family symbol of kindness and happiness.

How to make a stork from plastic containers

To make such a craft, you need to stock up on free time and be creative.

My patio is adorned with a stork figurine based on a 5 liter plastic bottle covered with polyurethane foam and painted with acrylic façade dyes.

Here is such a wonderful stork obtained from a plastic bottle and polyurethane foam

What materials and tools will be needed

Creating your own bird design, you can assemble it entirely from plastic containers, fastening them with glue or staples. And you can make the sculpture more expressive by adding wood details to the plastic structure.

The frame of this bird is wooden, covered with plumage from plastic bottles.

Or make individual elements of foam.

You can create such an exotic collection using ordinary plastic bottles and a piece of foam.

For our crafts of impressive size, you will need:

Canister plastic 5-liter - the basis of the body.
The 5 l canister forms the basis of the torso
Milk plastic bottles of 1 l and 1.5 l, from which white plumage is cut. You can get by with a transparent container, but first it should be painted with white paint for outdoor use.
Dark plastic bottles of different capacities: 3 half-liter will be needed for the manufacture of paws and beak, one and a half liter - for dark feathers.
Plastic container dark color needed for feathers, legs and beak
Styrofoam 10 cm thick, from which the head of a stork with a beak is cut.
A bird's head is made from a piece of foam
Sandpaper.
Scissors.
Corrugated tube for the neck.
A long bird's neck is made from a corrugated tube
Metal mesh as a base for the wings.
Furniture stapler.
Metal rod 6–10 mm thick for the legs.
Wire thin for fixing the wings.
With the help of wire, the wings are firmly attached to the model of the body.
Self-tapping screws.
Glue gun or universal glue.
Glue universal quickly glues plastic and other materials
Acrylic facade paints, brushes.

Stages of making a stork

Having acquired tools and materials, they first prepare all the details of the bird, then assemble it.

Head

A head with a beak is cut out of the foam plastic with a sharp knife.

A bird's head is cut out of a piece of foam

Then sand the rough surface sandpaper. You can cover the workpiece with white facade paint.

The workpiece is sanded with sandpaper to make the surface smooth.

To strengthen the beak, 2 triangular plates are used, which are made from a dark bottle of 0.5 liters. Having cut off the neck and bottom, cut along the resulting cylinder and cut out triangles. The plates are bent in half and attached to the beak with self-tapping screws.

The beak is made out of plastic, attaching it to self-tapping screws

Paws

They are made from the top of brown bottles of 0.5 liters. Containers with a cut off bottom are cut to the neck lengthwise into 4 parts, sharpened at the ends and bent outward.

Paws with fingers are cut out of dark bottles

Plumage

The most laborious and longest stage preparatory work- blanks of feathers. They will be required a large number of, of different lengths, shapes and colors: for the design of the wings and tail - long, dark and white, for the body - light smaller ones.

For crafts use light and dark feathers

The neck and bottom of the bottle are cut off, the remaining middle part is cut along and strips are cut out of the resulting rectangle. One edge of the strip is rounded. From liter bottle make 6 large feathers.

1 liter white bottle is divided into 6 parts

For plumage of the neck, small feathers are cut out and the ends are made in the form of teeth or fringe. You can decorate a long neck with large plates from halves of milk bottles, which are finely chopped around the edges.

figure frame

The body is made from a canister with a cut off handle.

A canister with a cut off handle is the body of our bird

As the basis of the wings, a fine-mesh metal mesh is used, which is fixed to the canister with wire or staples. The mesh along the edges is cut in the shape of a wing and bent down.

A fine-meshed mesh is fixed on the canister - the basis of the wings

A wire is inserted into the neck of the canister and bent, forming the frame of a long neck. Fasten the wire to the metal bar of the legs and put on it a corrugated tube or hose from the vacuum cleaner.

Strengthen the wire for the neck and put a hose on it

A hole is made in the lower part of the container and a bent rod is threaded into it - these will be the legs.

The legs are made of wire by bending it and threading it through the hole at the bottom of the canister

Or they pierce the canister from below and insert curved rods, on the ends of which they put the paws upside down.

Assembly of parts

After preparing all the details, the structure is assembled.

The head is put on a wire and additionally attached to corrugated pipe glue.
Cover the body with plumage starting from the bottom. Light feathers are fixed on the canister with staples.
Begin to screw feathers from the lower part of the body
They form a tail of feathers, placing them in rows and fixing them on the body with a stapler.
Feathers are screwed with wire to the edge of the mesh wing. To make the plumage of a stork with black edging along the edges of the white wings, the first two rows are made from dark feathers.
The wings begin to be decorated with feathers from the edge, using dark-colored blanks
Subsequent rows are formed from white feathers, overlapping them.
The third and subsequent rows on the wing are made of white feathers.
A number of feathers are screwed at the base of the neck with self-tapping screws.
It is not difficult to make a stork with sweeping wings
In this case, the feathers are screwed onto the entire canister, and the mesh base of the wing is covered with plumage on both sides.
On spread wings, feathers are attached on both sides.
Decoration of garden sculpture
By decorating plastic craft can be made brighter, especially if only transparent bottles were used in its manufacture. For this, acrylic dyes for outdoor use are suitable. Pre plastic container wipe with an alcohol-based solution and paint over with white or black paint until the feathers are cut out.
Acrylic facade paint is moisture resistant and does not fade under the sun
The beak and paws are painted red or wrapped with red tape.
The beak and legs are painted red
Eyes are made from beads, decorative blanks for toys or small buttons that are put on glue. You can just paint them with black paint.
Acrylic paints become brighter after varnishing.

Master class on making a stork
There are many options for making a stork from plastic containers using elements made of wood, polyurethane foam, and polystyrene.
Such an original composition of the stork family in the nest is also made of plastic
Even a beginner will be able to make such a garden sculpture, guided by video footage from step by step instructions workflow.
Video: how to make a stork from plastic bottles

Storks from plastic bottles - original decorative ornament personal plot and the subject of universal admiration. After all, they are made from ordinary garbage, turned into skillful hands into works of art. Made of durable plastic, they are not afraid of rain and snow. Over the years, the figures will not swell, the paint will not fade or peel off.

Have you thought, dear readers, that it can be used as ... a material for the manufacture of art objects. Although it may not be art, as such, in its literal sense, but a decoration for the garden - a small sculpture, it is quite possible to do. Indeed, polyurethane foam is unusually plastic, quickly hardens and is easily processed - why not a material for creativity?

Today I will tell you how to make a sculpture of a stork out of polyurethane foam to decorate your garden or suburban area. There are very few materials needed, and they are very cheap. If you pay attention to how much garden sculptures V construction stores, then you will understand that the price of a pair of foam cylinders is incommensurable with their cost. In addition, the stork will work out much better for us. So let's get started.

stork frame

To begin with, we will select a suitable body for the stork - a frame on which foam will be sprayed. plastic canister from under water with a capacity of 5 liters, it will do just fine. We make the neck of the stork from wire, and to add volume, you can wrap strips of foam plastic on the wire. The legs of the stork can also be made from wire, and the nose and head can be cut out either from foam or from wood - whichever is more convenient and preferable.

Sculpture making

After making a simple frame, we start spraying foam on our sculpture - we do it carefully, presenting the contours of the finished stork. To make it easier, print out a large bird. If the foam does not fall as you intended, no problem - after drying, the excess is easily removed with a knife. By the way, if you wish, you can use real bird feathers for the tail - who knows, maybe you can do it instead of a peacock stork. After the foam has dried and finished with a knife, we paint the sculpture with the usual acrylic paint, fix in place in the garden, and invite friends to appreciate your creative genius. Good luck!

An old legend says that God gathered all the reptiles from the Garden of Eden into one bag and ordered the man to throw him into the sea with his own hands. And the curious Homo sapiens wanted to look at the creatures, untied the bag, and, of course, missed everyone. Vladyka became angry and turned this man into a stork so that he would protect other people from all kinds of toads and snakes. Since then, storks have always settled near a person, feed on reptiles and bring us happiness.

Many old pictures depict a stork with a baby. Among the Slavic peoples, it is customary to believe that this particular bird is responsible for childbearing and well-being. If storks settled on the roof, the house will be full of happiness and children's laughter. And if you haven’t settled, then a wonderful stork with a baby can be made with your own hands from improvised material and installed on a skate or on an apple tree in the center of the garden.

bottled happiness

It will take

To make a stork from plastic bottles for the garden, we need to prepare the following materials:

empty bottles;
thick wide board for the foundation;
a rod or thick wire for legs;
a piece of foam 10 cm thick;
corrugated hose from a vacuum cleaner;
2 plastic canisters with a volume of 5 l;
metal mesh for wings;
stapler.

Master class on making happiness

It only takes a few hours of passionate DIY work to make almost real storks appear on the paths of your garden.

Cut out a head with a beak from a piece of foam, draw eyes or glue black beads with your own hands.

Cut out a two-piece beak from a dark bottle and glue it in place.

We begin the master class on making the torso by cutting off the handle in the canister. Then you need to bend the mesh in the shape of a canister with your own hands and cut off the excess.

To make the legs, bend the bar and fasten its ends to the board.

We are holding a master class on the preparation of plastic feathers.

We attach the feathers to the canister, starting with the tail.

The master class on fitting the neck begins with attaching the reinforcement wire. Then a hose is put on it.

Attach small "feathers" on the neck with tape.

Fix the feathers on the grid.

The stork for our garden will stand with its wings folded, so we simply fasten all the feathers with a stapler with our own hands, overlapping each previous row by a third.

We finish the master class by connecting all the details and decorative tinting of the eyes, beak and legs. This bird can be installed with your own hands in the depths of the garden for the whole summer. It will not deteriorate from the rain and will not fly away.

Fashionable toys today, hand-sewn from plain fabric according to simple patterns. We will not fully describe the master class for their manufacture.

Cut out the details of the craft from the fabric, sew and stuff with any filler.

Separately, you need to make a beak (can be made of cardboard) and attach to the head. It remains to make clothes, glue eyes, wrap the baby and hand it to the stork.

Of course, you cannot settle such a wet bird on the branches of a garden, but flower pot on the windowsill she can decorate.

Another way to make your home rich and happy is to make a stork on a nest. As a basis, you can take patterns of a tilde bird. Cut feathers out of plastic white milk bottles, fasten them together and make wings, decorating the ends with real feathers. Place a few white feathers on top of your head. Form a tail out of real feathers, sew or glue eyes and a tie, and plant the bird in the nest.

It can be made from ordinary rods, fastened with wire. To get a stork with a baby, put any doll in his wings. The master class on making a lucky amulet is over.

These two rag birds cannot be left on the paths of the garden, and the master class for making the first stork requires a lot of time and materials. Do not be upset and just make a nest and cut a flat bird out of textolite or plywood. Color it in, give it a string bag with a baby doll in its beak and that's it, the stork with the baby has already settled on your roof.

We all know the song from childhood "Stork on the Roof - Peace on Earth" for a long time. And Alena Zinovieva, already familiar to us from the village of Chastaya Oakwood, decided to plant a couple of white storks in love in her garden, which symbolize peace in her friendly family. These beautiful birds are also made from waste material : plastic foam, metal mesh, plastic bottles and plastic cans.

For the manufacture of storks we need:

1. Two canisters of 5 liters
2. Metal mesh for wings
3. Strong wire
4. Plastic tubes for legs and neck
5. Styrofoam for the head
6. White milk bottles
7. Dark beer 1.5l
8. Hose from a vacuum cleaner (can be replaced with a corrugation)