How to quickly remove old vinyl wallpaper from the walls. How to remove old wallpaper yourself? How to tear off vinyl wallpaper on a paper basis

Classic paper and washable vinyl wallpapers fit into any interior. Finishing material is inexpensive and looks good on walls and ceilings. Fills rooms with comfort and creates a unique atmosphere. But when it comes time to update the renovation, the wallpaper makes the apartment owners nervous. Both paper and vinyl varieties are firmly glued to plaster or concrete surface. How to save time and quickly clean the walls?

Preparatory stage

It is impossible to remove the finishing material without dust and crumbling plaster. Furniture from the premises in which the repair will take place is transferred to free rooms or put on the balcony. Massive wardrobes, sofas and other items are moved to the center and covered plastic wrap. The floor is covered with old newspapers, and the baseboards are sealed with wide construction tape.

It is advisable to de-energize the apartment. Hiding under the wallpaper electric wires, which are easy to touch with a spatula or wet, provoking a short circuit.

You can’t do without a stable stepladder, comfortable old shoes and clothes that you don’t mind getting dirty. A drill with a grinding nozzle, sandpaper, a bucket will come in handy warm water and glue packaging.

Spatula and kitchen knife

WITH finishing coating, which is more than 6-7 years old, tools with a sharp blade can handle it. Old wallpaper separates from the walls on its own due to dampness and time. It is necessary to find swollen areas, pry off peeled paper kitchen knife or the edge of a spatula, and then slowly pull. Paper varieties become dilapidated, so they cannot be jerked sharply. Pieces that have eaten into the plaster are pryed off with a wide spatula. Islands that could not be separated from the base are treated with water or a grinder.

Vinyl and non-woven options are easier to remove. A canvas with a water-repellent coating is cut in the middle and pry off the edges with a spatula. The lower half is pulled by hand, then the upper half is removed, and the remnants of the paper base are brushed off with a stiff-bristled brush.

Attention: Do not rub the plaster too hard or concrete wall especially in old houses and apartments. The material crumbles and falls off, leaving holes and dents. You have to spend extra time and money on priming and leveling the walls for new wallpaper.

Water procedures

A fresh finishing cloth, which is up to 4–5 years old, is pre-soaked. The liquid dissolves the glue and softens the paper, protects the plaster from destruction. Warm or hot water will do.

Wallpaper with a water-repellent coating is treated with a roller with sharp spikes. If the house does not have such a tool, an ordinary knife will come in handy. With a sharp blade, make wide incisions around the entire perimeter. The more holes, the easier it is for liquids to seep into the paper layer.

With wallpaper that ordinary water could not soften, special solutions will cope. The canvas glued to the wall with PVA is treated with laundry soap. A bar of detergent is crushed, poured into a saucepan. Pour 3-4 liters of water and, stirring, bring to a boil. In a hot workpiece, a roller or foam rubber sponge is moistened. Impregnate the finishing material with liquid and wait 20 minutes for the soap to work.

Fabrics with water-repellent properties are impregnated with a solution prepared from fabric softener. Add 200–300 ml of the chemical component to a bucket of liquid. The concentration is increased if there are several layers on the wall finishing material.

Construction glue and PVA will dissolve table vinegar. connect bucket hot water and 400 ml of the product. The mixture is added with shavings from laundry soap if the plaster crumbles a lot, and the wallpaper is literally eaten into the base.

The solution is applied to 1.5–2 sq. m. finishing material. It is impossible to process the entire room at once, because part of the room will dry out, and you will have to repeat the impregnation to clean the walls of wallpaper. Water softens the paper base of the rolls in 20 minutes, solutions work twice as fast.

The liquid product is applied with a paint roller, a soft cloth or a large foam sponge. Wallpaper in old houses is sprayed with a spray gun so that less liquid gets on the walls. If too much water is applied, it can soften plaster and putty.

Wetted canvases are pryed with a spatula with a wide blade. The remaining pieces are sprayed with a spray bottle and cleaned off sandpaper with a water-repellent coating or a metal brush. Choose varieties with stiff bristles.

The remains of wallpaper and plaster are immediately swept into a pile so as not to trample dirt into the floor. Walls finished soapy water, it is advisable to wipe with a sponge dipped in clean warm water. The liquid will remove the remnants of powder and fabric softener. Household chemicals soaked into concrete base and interacts with the adhesive, worsening its properties. New wallpapers will not hold well, they may swell and fall off on the first day.

Steam cleaning

High-quality glue, which could not be dissolved with water, is steamed with an iron. You will need a sheet or thin towel, a bucket of water and an assistant to hold the fabric:

1. A rag is dipped into a container with liquid, twisted and applied to the wall, covering pieces of finishing material.
2. The iron is turned on and the maximum temperature is set.
3. The sheet is ironed with a hot device several times.
4. The rag is removed and the remnants of the wallpaper are quickly removed with a spatula.

The paper web is also softened with a steam generator or steam cleaner. Household varieties are useful on the farm. Devices remove dirt from outerwear And upholstered furniture. Construction steam generators have limited functions, so repair professionals buy such equipment.

The wall is ironed with a steam cleaner, placing a clean, dry sheet under the device. If you do not use a rag, dust and dirt get into the equipment, which can cause a breakdown.

Paper wallpapers are easier to work with. Ironed and removed. If you have to steam vinyl varieties or non-woven, it is recommended to first remove the water-repellent film, and then turn on the iron. Paper particles that could not be removed in this way are scraped off with coarse sandpaper or a spatula.

Hot steam penetrates the putty, so the cleaned walls are dried for several days, and then primed and painted or new wallpaper is pasted. If a finishing material is applied to a wet base, mold will appear.

Special formulations

People who do not have time to scrape and steam are advised to buy an instant wallpaper remover. The product is sold in construction stores. Usually it is a powder or thick jelly that needs to be diluted with water. The most popular are Atlas Alpan and Quelyd Dissoucol.

In a solution prepared from a powder, the roller is moistened and the wallpaper is treated. Small incisions are made on canvases with a water-repellent coating. It will take 2-3 hours for the product to dissolve the glue and soften the paper layer. The wallpaper will begin to lag behind the concrete base on its own. Cloths pry off with a spatula or hands and rip off the wall.

Manufacturers claim that solvents are safe and do not emit toxic fumes, but it is better to work with rubber gloves. Make sure that the product does not get on open skin and mucous membranes.

Wallpaper, glued in several layers, is treated with a special solution. Not only powder is added to the water, but also glue, so that the mass becomes thick, like jelly. Such a tool is better absorbed and softens all paper bases.

Unusual Options

Liquid wallpaper is one of the best inventions of mankind. Finishing material does not need to be scraped off and torn off. The walls are sprayed hot water and wait 2 hours. Wallpaper gradually absorb moisture and swell. Some areas fall off on their own, others are easily removed with a wide spatula.

Glass fiber cannot be removed without special washes. The finishing material is treated with a solution and left for several hours. When the canvases swell, they are armed with a spatula or a kitchen knife and peel off the wallpaper from the walls. After the procedure, the concrete base is dried, puttied and primed.

Non-woven and vinyl wallpapers do not have to be completely removed. Rip off only upper layer with water repellent properties. The paper bottom is left if the walls are even, without cracks and holes. New canvases are glued on top of the old wallpaper.

Drywall

Concrete walls are not afraid of water and a grinder. Plasterboard partitions covered with paper. You can’t remove it, otherwise you will have to throw away the old plates and buy a new finishing material.

Clean the plasterboard base from the wallpaper will help cheap building glue. Several packs of powder are diluted with warm water. Stir so that there are no lumps, and apply a thick mass to paper or vinyl sheets. Leave for 3-4 hours. The product dries slowly, soaking into the wallpaper. They swell and soak, so they are easily separated from drywall.

The glue should be thick so that it does not spread over the entire wall. The solution is applied in a thin layer, otherwise it will be absorbed into the drywall. A little primer is sometimes added to the workpiece. The tool will make the liquid for dissolving the wallpaper viscous. The mortar will dry more slowly, plus the primer will prepare the plasterboard walls for further repair work.

If there are old wallpapers from grandmother's times in the closet, the rolls are not thrown away. The canvases are cut off and glued to the walls treated with glue and a primer. Old wallpaper softens and sticks to the top layer. You just need to pull the edge of the canvas, and the walls will become clean. No need to get a spatula and turn on the drill.

In apartments built in the 50s or 60s, it is recommended to remove only the top layer of wallpaper. Let the rest stay. The walls in old apartments are thin and uneven, so light redecorating can turn into large-scale construction works.

Thin paper sheets that could not be peeled off with water and special solvents are cleaned with a drill. A brush with iron bristles is put on the tool and the concrete base is ground. Irregularities remaining after removing the wallpaper are recommended to be repaired with acrylic putty. It is inexpensive and of high quality, suitable for leveling walls. Putty is applied with a rigid spatula from of stainless steel so that it lies flat on the base.

Gypsum boards will have to be replaced if the wallpaper is glued with PVA. In this case, neither a solvent, nor a sharp spatula, nor a drill with a grinding nozzle will help.

Modern washable wallpaper is easy to stick and remove. You will have to tinker with old paper varieties, but solvent and sandpaper will solve the problem. The main thing is not to forget to dry and prime the walls after removing the finishing material, so that the new wallpaper fits well and lasts for more than one year.

Video: how to remove old wallpaper correctly and quickly

Vinyl wallpapers have become popular in our country not so long ago, in this regard, those who decide to purchase them have a large number of questions.

One of the most frequently asked questions is how to properly remove this type of wallpaper from the walls. This procedure is not particularly complicated, so it will not take you too much time, but you need to know all the nuances and rules.

Perhaps this is the reason why they are so popular. It is also worth saying that vinyl wallpapers have two types of bases:

1. paper;
2. non-woven (how right?).

Depending on the basis, the method of wallpaper removal will be selected.. There are also several types of coatings:

• hard;
• smooth;
• silkscreen;
• foam vinyl.

Features of removing the old coating

Attention

In order for the new layer of wallpaper to look attractive and lay down smoothly and evenly, the old coating must be removed correctly.

Read about how to quickly and easily tear off old wallpaper.

To do this, you need to figure out how best to shoot vinyl wallpaper. It is necessary to remember only a few basic rules that must be observed, and in this case, this procedure will pass quickly and at the same time very effectively.

In order for it to go smoothly, you need to do some preparatory work to be done the day before the event.

1. For your own comfort, it is recommended to take out all large furniture from the room and, if possible, even small. By freeing the room from all the details, you will provide yourself with a sufficient amount of free territory.
2. The floor in the room can be covered with improvised means. First of all, this will prevent pollution, as well as slipping on the floor surface, which in turn will prevent injuries.
3. Prepare in advance the inventory that you will need to remove wallpaper from the walls. For this you will need:
   • a roller that has many spikes on its surface;
   • bucket for water;
   • putty knife;
   • ladder;
   • gloves.
4. The bucket will need to be filled with warm water. In order for the removal procedure to take place as quickly as possible, it is necessary to add a little detergent to the liquid.

How to quickly carry out the procedure, depending on the varieties of the base?

The correct removal of wallpaper from the walls begins with the fact that you must decide on what basis they are made. The method of removal will depend on what kind of base. Having decided on this issue and having prepared all the necessary equipment, you can proceed to the next important step.

You will need to de-energize the room in order for the removal procedure to be as safe as possible for you. After that, you can begin to remove the wallpaper, but you will also need to decide which method you want to carry out this procedure. There are many varieties of them, so after reading about them, you can choose exactly what suits you the most.

On a non-woven base

If the walls of your room are covered with non-woven wallpaper, then removing them will take place very quickly and without much difficulty. In order for you to be able to, it will be enough for you to just remove the top cover of the old ones.

To do this, it is best to use a roller that has spikes. They can easily walk on the surface of the walls, which will allow you to quickly and easily get rid of the top coating.

After removing this layer, you can immediately start sticking new wallpaper. This will protect your wall additionally from fungus and mold, and will also become a protective barrier against liquid.

Experts recommend moistening a layer of wallpaper with a small amount of liquid. This will help them soften somewhat and it will be very easy to remove them yourself, without using any auxiliary materials. In this case, the old wallpaper will peel off in one big piece, this is ensured by their dense material, which does not allow the wallpaper to crumble.

We offer you to watch a video on how to remove non-woven wallpaper from walls:

paper based

In the event that you start removing paper vinyl wallpaper, you can resort to many methods. Removing them is quite simple and fast:

1. You can use a regular spatula for this. Surely, every owner has such a tool and it will not even need to be purchased. Quite often, this method is used in cases where the wallpaper was glued to an existing layer of paper.

   Thanks to a large number paper coating spatula will be easy to remove it, especially if the walls were previously wetted with liquid. This will allow the old wallpaper to soften and peel off later in large pieces.

2. The second way is to use a roller with spikes at the first stage, and then wetting the second layer of wallpaper with liquid. The roller will allow you to quickly remove the top layer of vinyl wallpaper, which is impenetrable. For your convenience, it is better to start this procedure from below or from above, but not from the middle of the wall.
3. Another option is that instead of liquid, you can use special means for removing vinyl. You can find it at any hardware store at a reasonable price.

   But remember that even in this case, you will need to remove the top layer of old wallpaper with a spiked roller, as it is impenetrable. If you do not remove this layer first, then the funds simply will not get to the right place and will not work.

4. Immediately both layers can be easily and quickly removed with special device, which releases hot air - a steam generator. If you have such a tool, then the withdrawal procedure will pass for you quite quickly.

From plasterboard walls

It is best to use special tools that are designed for. You can also use water, but keep in mind that only a very small amount can be applied to the surface of the wallpaper.

The removal technique is almost the same as for removal. ordinary wallpaper . But it is also worth noting that it is not recommended to use a spatula, as it can easily damage a smooth and delicate drywall wall. Remember that all your actions when performing this procedure must be performed very carefully and slowly.

Experts recommend that you carefully read all the rules that provide information on how to properly remove the wallpaper, and carefully follow them (from the walls?). You need to be especially careful when your walls are made of drywall.

1. Do not wet the entire area of ​​\u200b\u200bthe room with water immediately, do it gradually.
2. Try not to put too much liquid on the walls.
3. If you are afraid that you will not cope with the removal, then you can purchase a special liquid for this procedure and be sure that everything will work out with it.

Summing up, it is worth saying that Removing vinyl wallpaper is a simple procedure, the main thing is not to rush anywhere and follow all the rules. In this case, everything will pass quickly, and you will not have to put too much effort into it.

In contact with

When re-gluing, carefully remove old layer wallpaper, without leaving even small fragments. It is such a clean surface that will allow you to stick a new layer without blisters and bumps.

In 90% of cases, it is enough to use the most in a simple way wallpaper removal, and we will talk about it later, but if you are in the 10% of the "lucky ones" and the sweat is already flowing in a stream, and your nerves have begun to fail, scroll down the article, there we will talk about emergencies.

The easiest and fastest way

1. Empty the room of all furniture or arrange it in the center of the room and cover it with cellophane or newspapers.
2. For safety reasons, turn off the electricity in the apartment. Cover outlets and switches with masking tape to keep dirt out. And now the dirt will appear, believe me.
3. Prepare the following tools and materials:

• a bucket of hot or warm water;
• wide roller (can be old);
• narrow and wide spatulas;
• stopwatch.

1. With a wet roller, dampen 2-3 strips of wallpaper from top to bottom. Please do not flood the neighbors - pouring water excessively is not necessary.
2. Record 20 minutes. During this time, the material and glue will absorb enough moisture.
3. With a spatula, pry off the corner of the wallpaper and separate it from the wall. Clean up small pieces with a spatula.

1. Go back to step 4 and say goodbye to all the remaining canvases.

To clean the walls of a room of 20 square meters it might take two hours. More time may be needed if old paper wallpaper glued on the conscience, and even worse, on PVA glue. It will also take longer to process materials with a water-repellent layer, such as vinyl wallpaper.

Tip: Cleaned walls should dry. At least a couple of hours. Only then proceed to the new finish.

Life hacks and folk remedies

To make the wallpaper removal process even faster and more efficient, read what additional magic tools you have at hand. It's time for them to bring real benefit to humanity.

Difficult cases at work

What to do if you got vinyl or non-woven wallpaper

We act, as we described above, by the method of exposure to moisture, but before water procedures walk with a sharp knife or wallpaper tiger (most importantly something sharp) along the old wallpaper and make cuts. Water will penetrate under vinyl film into paper and it will not be difficult for you to finish your work on time.

What to do if old wallpaper is glued to drywall

Drywall consists (attention!) of gypsum and cardboard. For obvious reasons, the last of the components cannot be wetted with water. Therefore, in this case, it is best - either to carefully operate with a spatula, or, in last resort, buy a special solution to remove wallpaper.

What to do if the wallpaper is glued to PVA glue

Brace yourself. This is the most difficult case. Jewelry work. Water, even with an admixture of diamonds, will not help you. Take a sharp spatula and, forgetting about the plans for the whole evening, clean centimeter by centimeter. Or ask your neighbors for a grinder (grinder) and buy a nozzle with hard bristles - the process will go faster.

Watch this video - the need for invention is cunning:

If the old wallpaper is still on the wall

Guys, let's be honest, if you have read the article up to this point and the old floral wallpaper is still intact on your wall - either you are doing something wrong and better read the article slowly from the very beginning, or - you know what - leave this venture . If, with such inhuman efforts, you still failed to separate paper and stone now, then, believe me, they will never part again, and under no circumstances.

Vinyl wallpaper is a very popular option for decorating walls in a room today. But time passes, and the old coating loses its attractive appearance. In this case, it is necessary to make repairs and remove old canvases from the walls. And here the most interesting begins, because it is not so easy to remove such canvases.

If everything is done correctly, there are no difficulties in removing the old wall covering.

But do not be upset, because there are many ways that allow you to tear off the coating from the wall quickly and efficiently. At the same time, improvised materials are used for such events. Let's take a closer look at how to remove vinyl wallpaper from a wall surface.

Preparatory stage

When you need to remove old wallpaper from a wall surface, you need to clean the room. To do this, take out the furniture if possible or just cover it. protective film to keep dirt out. You can also protect the floor by covering it with the same film. At the exit from the room, it would be nice to put a damp cloth so that all the dust settles on it and does not spread throughout the house.

Protective film can be found in hardware stores

It is imperative to take care of turning off the electricity, and all those present lighting on the wall to be removed. You can quickly and efficiently peel off old material from the wall, provided that you have prepared the following tools:

• Roller with built-in spikes.
• Warm water container. If placed in a liquid detergent, this ensures easier wallpaper removal.
• Foam sponge.
• Putty knife.
• Masking tape, which is glued to all sockets present.
• Gloves.
• Ladder.

Needle roller will help when working with old wallpaper

The list of these materials is approximate, because for different cases various items may be needed, somewhere it will be possible to peel off the wallpaper easily and quickly, and somewhere you will have to make every effort to tear the coating off the wall.

Methods for removing old canvases

Related article: How to make a warm floor in the bathroom from heating in the apartment

Remove regular wallpaper on paper basis not difficult. To do this, you just need to moisten their surface with warm water, wait for a while until the liquid thoroughly saturates the canvas, and then use a spatula to remove the material from the wall. But unlike ordinary paper-based wallpaper, vinyl canvases have such qualities as water resistance. In this case, more than effective methods struggle.

Water use

In order to quickly tear off the wallpaper from the wall surface, it is necessary to use rolls with spikes. If there is no such device, then you can use with an ordinary knife but they have to be careful. Due to the multilayer structure, such wallpapers keep the wall intact. With the help of the presented tools, only the first layer of canvases is damaged.

The wallpaper comes off the wall perfectly, sometimes the backing remains

When you managed to make the first layer of material unusable, now you can take water, add dishwashing liquid to it and apply it to the wall surface. Thanks to the added component, the glue will begin to dissolve quickly, and the old wallpaper will be easier to remove. To moisten the surface, you can use a roller, foam rubber washcloth or spray gun. In this case, it is important not to overdo it so that damage does not occur on the floor and wall.

When the old wallpaper is saturated with water, you can carry out the procedure for removing them. The process of removing the canvases should occur from the bottom up. All remaining pieces of wallpaper are removed using a spatula. If it is not easy to remove the wallpaper from the walls, then you need to apply water to their surface again, and then remove them again. When vinyl wallpapers are very tightly and firmly attached to the wall, you can not remove them, but perform further gluing directly on them.

Steam application

Our masters told us interesting way how to remove vinyl wallpaper with steam, which is rarely used, but very effective.

Using a steam generator to remove wallpaper

You can quickly tear off old canvases from the walls with steam. To perform this operation, you need to stock up on a steam generator or an iron that has a steaming function. When performing such activities, the steam acts only on the first layer of wallpaper, as a result of which they begin to lag behind the wall.

Using steam is not only fast way removal of the old coating, but also the cleanest method, because after it no traces of dirt remain. In addition, this option can be used when you need to peel off the interlining.

As an alternative, you can try a wet rag and an iron. Matter is laid on the wallpaper, and then go through it with an iron. The effect obtained can be compared with that obtained from the use of a steam generator.

Related article: Why putty drywall?

Application of wallpaper paste

You can tear off old canvases from the walls using a special composition that dissolves in liquid, as well as a small amount of glue. The resulting product is evenly distributed on the wallpaper, and then allowed to rest for 3 hours. The applied method allows you to remove the wallpaper not in pieces, but immediately with canvases. It's simple, because when gluing the canvases, a different wallpaper glue was used.

Simple measures for dismantling wallpaper

You can also delete material using metal brush, sandpaper and grinder. But you need to carry out all activities carefully and carefully so as not to damage the wall.

Removing wallpaper from drywall

Very often people use to level walls drywall sheets. They are easy and quick to attach and do not leave behind dirt, as when using plaster. But what if vinyl fights need to be removed from such a surface? It is important here not to harm the drywall, otherwise you will have to carry out measures to restore it, and this is already a waste of time and money.

Do not use water to remove the canvases, because drywall does not tolerate moisture very well. The process of removing material must be carried out very carefully. First, a small amount of water is applied, then you need to wait until the top coat of the wallpaper is wetted and then take a spatula to carefully remove the old material. In this case, you can add special products to the liquid that are designed to remove exactly the vinyl coating.

Plasterboard walls ready for wallpapering

If the gluing process was carried out on a special glue for vinyl sheets, the dismantling process will not be difficult. Also, difficulties will not arise, provided that putty and primer were applied to the drywall sheets before applying the wallpaper.

It is very easy to remove non-woven fabrics, because it is possible to delaminate them. To do this, pry off the top layer with a knife after wetting it with water and peel off waste material. If you used PVA composition for wallpapering, then you won’t be able to harm the coating. In this case, the integrity of the sheets is necessarily violated.

Repair in an apartment or house brings with it a huge number of different problems and troubles. No wonder it is considered that repair is equal to three fires and two floods. Huge efforts and funds are invested in the renovation. To get rid of unnecessary troubles and problems, so that the funds are not wasted, and the efforts are not in vain, preparatory operations should be carried out correctly. No matter what it will be wall covering - wallpaper, painting, decorative plaster, the wall should be as flat as possible. But first you need to clean it. Let's learn how to remove vinyl wallpaper from walls. This is a very popular type of wall decoration. This material has some features that should be taken into account.

Features of vinyl wallpaper

This wallpaper consists of two layers of materials. Often the first is paper or fabric base. The second layer is a polyvinyl chloride coating. Due to the presence of a paper base, these wallpapers are easy to stick. The polymer finish layer provides these materials with high resistance to moisture, and also makes the coating durable.

The vinyl top can be finished in a variety of ways. There are so-called washable wallpapers, foamed, with silk threads. These surfaces are easy to clean. Some can be washed with water. Others - alcohol and even a solvent. That is why you need to know quickly and without problems. The fact is that traditional paper wallpapers can be easily removed with plain water. But she won't help here.

The method of removing wallpaper also depends on what kind of glue was used during installation. If a professional composition was used, then these are water-soluble mixtures. In this case, the old finish is easily removed. Also, these wallpapers are glued with water-insoluble adhesives - these are PVA, bustilat and others. Then more effort will be required. Home masters advise how to remove vinyl wallpaper from the walls. There are two ways: in the first case, they act on the glue, and in the second, directly on the wallpaper itself.

Preparatory stage

Before you start removing the vinyl wall covering, you need to prepare the room. It is best to free the room from furniture. In the process of work, it can get dirty and just interfere. Interior elements that cannot be removed are covered with a film or sheets. It is also better to cover the floors with a film. Lay sheets of cardboard on top of it or enough thick paper. A damp cloth is laid on the threshold. It will collect dust and debris on itself.

To avoid accidents with electricity, experts recommend de-energizing the wiring. To reduce the risk of moisture getting into sockets, it is recommended to cover them with a film.

Materials and tools

Before removing vinyl wallpaper from the walls, you should prepare fixtures, materials and tools. First of all, a wallpaper tiger is prepared - this is a roller with spikes. Then you need a knife, scrapers. Sponges will come in handy different sizes, as well as foam rubber rollers, rags and rags. Prepare basins and containers for water and solutions, a ladder, garbage bags. Work is best done with gloves.

How to remove vinyl wallpaper: ways to remove wallpaper from vinyl using water

First of all, the vinyl surface is carefully treated with a spiked roller. This is done so that holes form in the moisture-resistant vinyl coating. It's not such a simple process. It will require a lot of effort and time. Wallpaper tiger or roller easily breaks through the layer without damaging the wall.

Then the surface is liberally moistened with a warm solution of water, vinegar and fabric softener. It must be remembered that this method is suitable for paper-based coatings. In the area of ​​​​sockets and switches, the solution is applied very carefully. Fast is not always good. Water will enter the holes and cuts, causing the adhesive to swell. Within 15 minutes, the wallpaper can be easily removed from the wall. The thicker the layer of glue, the more intense the moisture should be.

Professionals advise how to remove vinyl wallpaper from the walls: it is better to start shooting from below. To do this, the edge is hooked with a spatula and removed. The remaining small fragments can be removed with the same spatula or coarse sandpaper.

Method number 2 for dismantling wallpaper using water

Here, too, the vinyl coating is first treated with a roller or tiger. Then moisturize. The peculiarity is that instead of water, special formulations are used. They are mixed with warm water and applied to the surface. This tool does not act on the paper base, but on the glue. The wallpaper itself will remain intact and undamaged. The composition will dry in 2-3 hours - the manufacturers indicate this in the instructions. Then the canvas can be easily removed almost entirely.

If the coating is poorly removed, in such cases, add water with a special solution. This composition covers the wall and leaves it for several hours. Then the wallpaper is easily separated from the wall in a single strip without gaps. Some give other recommendations on how to remove old wallpaper. We will talk about them below.

We use a steam generator

Here's another one effective method how to remove old vinyl wallpaper from walls. It is good because it allows you to quickly remove old finish. Under the influence of hot steam, the glue will swell and dissolve much faster than in the second method. If there is no such generator, then an iron with vertical steam will do.

This method is also good because it eliminates the appearance of dirt.

Mechanical Methods

Professionals know that waterproof adhesives can provide the best adhesion for vinyl wallpaper to the wall. This is the advantage of this method. But it is very difficult to dismantle the wallpaper glued in this way. This is not an easy or quick process. In this case, the wallpaper can only be separated mechanically. So, they take a sharp spatula and pry the edge of the sheet with it - at the junction, near the sockets, at the bottom. Next, you just need to peel off the coating. Wetting surfaces is useless. If the bottom layer begins to swell, then this is paper, not glue.

Dismantling wallpaper with a spatula is a long process. How to remove vinyl wallpaper? Removing wallpaper from vinyl mechanically will be faster if you use a power tool. Can apply grinder, electric drills with special fittings. But you have to use the right tools. This removes small pieces and traces of glue, but not completely the canvas.

We work with plasterboard walls

If there are no special problems with an ordinary wall, then there may be problems with drywall. This material does not survive the effects of moisture, and even more so water. The method of dismantling with abundant wetting is not suitable here. Experts recommend as the most the best option apply special compounds that dissolve the glue. If the wallpaper was applied to drywall with PVA adhesives, then it will not work to remove them. You need to change the entire element.

Tips on how to properly peel off vinyl wallpaper on a drywall wall

As noted above, vinyl wallpaper can be made on a paper or non-woven basis. How to remove old vinyl wallpaper from walls? The methods are the same as in the case of a conventional wall. The wallpaper is sprayed with a special solution, and the non-woven ones must first be treated with a wallpaper tiger. Only after that it is allowed to moisten them. Only half an hour later you can start dismantling vinyl trim walls.

Some types of wallpaper will require the use of special tools. But you need to work very carefully, as you can easily damage the wall. It is very difficult to remove washable wallpaper. Their coating is made in such a way that they are not afraid of moisture. Here it is best to use irons or steam generators. By removing the coating in small pieces, you can get good result on one's own.

Especially easy to remove paper wallpaper, as well as liquid. The latter can not be removed at all - with the help of special paints you can simply change color scheme and change the drawing to your liking. However, if the task is to apply a different coating to the wall, then in order to remove the liquid-type wallpaper, an aqueous solution is suitable or Sander. But there is one drawback - after mechanical removal, you will have to re-grind the wall. This is an additional waste of time. We'll have to re-clean the room from debris.

Conclusion

In order for the new wallpaper to please the eye and serve for a long time, you need to have a lot of patience. Now you know how to remove vinyl wallpaper from a wall. Peeling off the old ones with the help of these recommendations will not be difficult. After the wall is cleared, do not rush. Let it dry. Then you can safely apply a primer.