Master class on chair upholstery. Upholstery of chairs with your own hands. Is it difficult? How to reupholster an old chair with your own hands

Beautiful cases different shades Usually used to perfectly disguise worn upholstery on chairs. This option is really good. Should I spend money on purchasing covers if the chair doesn't look good enough?

If you decide DIY chair upholstery, be sure to find out for yourself which installation work will be needed. It is up to you to decide whether the upholstery needs to be replaced.

Restoring a chair is quite simple. But the work requires careful attention. The previous fabric is completely removed. After this, a thorough inspection of the entire surface will be required. If necessary, repairs are carried out. Then a new filler is prepared and the upholstery fabric is strengthened without fail.

Upholstery. Preparatory work

You want to do any job efficiently and quickly, chair upholstery is no exception. And when you do it yourself for the first time, there can be a lot of “delays.” For this you need to be prepared.

Any fairly thick fabric will do. If desired, leather (artificial or natural), wool or tapestry can be used.

Foam rubber is suitable for padding certain thickness. Batting, latex, and padding polyester are also often used.

Don't forget a furniture stapler, pliers and a screwdriver. You will need them during the restoration process.

Your chair may need some preliminary repairs. If it is “flimsy”, then it must be carefully glued, perhaps nailed somewhere. this needs to be done on preliminary stage. In this case, you will not have to remove the updated upholstery later.

And also this advice: “If a chair is “flimsy”, its wooden part is “dead,” then throw away such a chair and buy a new one. Restoration is relevant when the repaired chair is no worse than a new one.”

Removing old upholstery

The chair is pre-disassembled. The first step is to carefully remove the seat. Then the chair must be turned over. Then unscrew the bolts and remove the brackets. All work must be performed with the utmost care. There is no need to rush in such a matter. As a result, you will be able to perform upholstery on high level. Use pliers to remove staples. The screws can be easily removed using a regular screwdriver.

Be sure to find out how stable the entire structure is. If the legs are loose, they must be strengthened. All loose connections are sealed. To seal cracks, a mixture of sawdust, PVA glue and dye is used.

If repairing the chair is not needed, then start by removing the old fabric. After this, you can proceed to creating a new upholstery. The staples are removed carefully.Often, old upholstery material can be used when creating a pattern. Now the removed upholstery can be thrown away. The same manipulations are done with the back. The work is carried out in the same sequence as we described above.

Features of fabric and padding

Prepare the foam and fabric of your choice. Make a pattern. A strong and tight fastening of the material is required. It is important to use a template. It is made from paper. I use wallpaper for this. The process itself is not difficult. After the chair is completely disassembled, the seat is placed face down on the paper and carefully traced around it. It is required to retreat at least 5 cm from the line. This margin is provided for hemming. The template is carefully cut out and everything marked is carefully transferred to the material.

Good for stylish upholstery:

Furniture fabric of sufficient density. We recommend paying attention to high-quality wool, carpet fabric, velor with or without ornament.
High-quality leather (artificial or natural).

The choice depends directly on the features of the interior and the textiles used in the interior. It is important that chairs and upholstered furniture are in harmony in style and color. We recommend choosing textiles that are ideally matched for bedspreads and at the same time closely follow the pattern of the curtains.

Foam rubber is traditionally used as padding. For optimal reliability, we recommend carefully placing it on the seat and gluing it. Do not use a thick piece. In this case, it will simply be uncomfortable to sit on the chair. It's best if you focus on old material. You need to purchase not only textiles and foam rubber, but also suitable threads. Use only those with optimal strength. At the same time, they must match the color of the fabric. If the edges of the fabric need to be hemmed, you simply cannot do without them. This will also be needed when the pattern is not so simple and is made not from one part, but from several.

Do-it-yourself furniture reupholstery

To change the upholstery of chairs correctly, you must follow a certain sequence:

Initially, the foam rubber is glued to the base. At the same time, all excess is carefully trimmed. Don't forget to fold the edges before doing this. To strengthen the hems on the wrong side, staples are used.

Then they move on to cutting the fabric. Place the fabric on a perfectly flat surface (face down). A seat is placed on it (foam down). A reserve is left for the obligatory hem. The rest of the fabric is cut off.

Used for fastening upholstery furniture stapler. The fabric is stretched well. It is important that there are no folds or free spaces. Before this, the upholstery is folded, and the necessary points are outlined at which fixation will be made.

The upholstery depends entirely on the shape of the seat. It is much easier to do the job if the piece of furniture is rectangular. If it is round, you will have to try. The same can be said about the chairs.

Be sure to pay close attention to how the legs are secured. Often special cutouts are provided for them on the seat. In the process of attaching fabric and foam rubber, you will have to remember this. It is necessary to make cutouts so that this space is completely free.

Take into account the size and shape of the grooves for the legs. If you do not take this into account in time, you will not be able to produce high-quality upholstery. It will no longer be possible to carefully assemble the chair if you do not provide cuts in the fabric. There really is a way out of this situation. But it requires some patience. When you create a pattern, you need to select small wedges. They will very beautifully surround the cutouts designed for fastening.

In order to change the upholstery of your old, but beloved chairs, you will not need a significant time investment. Don’t forget about the neat design of the back. There is an option to replace the method of fastening the material from staples to nails (and sometimes vice versa).

Here's the video of the process of self-upholstery:

The fabric is carefully stretched over the foam. They attach it with staples. This will allow you to nail the nails correctly. In this case, folds are guaranteed not to appear. Then the fastener itself is performed. They always start from the top. The fastener pitch varies. It is not recommended to make it very large.

Restoration involves not only the obligatory polishing and subsequent painting of all its wooden parts.

I think you understand that upholstering chairs with your own hands is not particularly difficult. But for some reason, everyone can cope with such work.

Furniture workshop "Encore" is ready to reupholster your chairs, armchairs, sofas if you can't do it yourself!

Sooner or later even quality furniture and even with careful handling it becomes unusable. This is especially true for chairs, armchairs, and sofas. The upholstery wears and tears, and stains appear.

What to do if your comfortable chairs have lost their former presentable appearance? Do not rush to send them to the dacha or the trash. If the design of the chairs is still strong, then they have the right to a second life in a new look.

Upholstering chairs with your own hands or with the hands of specialists will help you with this. Photos of chairs before and after restoration will help you get inspired and stock up on fresh ideas.

Why do you need a constriction?

First of all, this will save you money. New furniture good quality It's not very cheap. And the furniture of the last century, if you work with it well, will easily outlast the inexpensive modern furniture. This is also an opportunity to choose the color and texture of the upholstery material that best suits your interior.

And again, any work with your own hands is a creative process that brings pleasure. This is an opportunity to create something unique, to put warmth and love into your home environment.

Another plus is that you don’t have to go shopping to find the right chairs that will match the rest of the furniture in your home. This is especially true for kitchen and dining sets, where chairs and a table come from one set.

Preparatory work

First of all, you need to get rid of the old upholstery and filling. The tools you will need are an anti-staple gun or a flat-head screwdriver or pliers.

We unscrew the seat, if there is a backrest, then that too. We take out staples, nails, screws. We clean the surface of the chair from everything unnecessary, from glue residues, from old foam rubber.

If there is a need for minor repairs to the chair frame or springs, these need to be done. Cracks should be filled with glue or sealant and puttied.

If you wish, you can update the color of your chair. First go over its surface sandpaper. Next, the surface needs to be degreased, and after painting, varnished.

It is very important to be careful when dismantling so as not to damage individual parts of the chair. The old upholstery can be used as a pattern. Or take new measurements using a measuring tape.

You will also need a furniture stapler and staples, or a hammer and nails, tailor's scissors, a utility knife, a long ruler, a chalk or something similar.

Selection of materials

It is important to take into account the density of the fabric; it should hold its shape well. And easy to clean. The most commonly used are tapestry, flock, chenille, and jacquard. They are quite strong compared to other fabrics. The list of materials also includes leather and leatherette.

It is important to take correct measurements before purchasing. Don't forget to take into account the width of the hem and the height of the filler, this is approximately plus 15-20 cm to the original length of the fabric.

The color of the upholstery plays a big role. It should fit harmoniously into the interior. Dark colors are considered more practical, while light upholstery is more demanding to maintain. Can be combined different materials in terms of color and texture.

What to choose as a filler?

Most often this is sheet foam rubber. It comes in different thicknesses, the optimal thickness being 4-5 cm. You can use padding polyester as a lining between the fabric and foam rubber.

This method will simplify further stretching of the fabric and eliminate unnecessary folds.

Let's start re-upholstering

For convenience, you can make a stencil from thick cardboard and cut it using a stationery knife. the right size foam for the seat. Afterwards we glue the filling to the plane of the seat.

You can use PVA glue or another suitable furniture works glue. Give the glue time to dry. Using the same template, we cut out the blank from the upholstery material. Don't forget to leave a hem allowance of 7-10 cm around the entire perimeter.

Now let's move on to the actual upholstery. Lay out the material on flat surface face down. Then a layer of padding polyester, if you decide to use it, and then the seat itself with foam down.

We carefully bend the material, do not stretch it too much, and nail it with staples or nails. Try to make a more or less even line. It is better to start fastening from the center and spread evenly to the sides.

Having finished on one side, go to the opposite, do the necessary stretch, smooth out wrinkles if they suddenly appear. The distance between staples is 1.5-2 cm. But if shaped waves form on the side surface, then in this case you can hammer in staples or nails more often.

Please pay attention Special attention corners to make them as neat as possible. If necessary, tap the staples with a hammer. The back is tightened in the same way.

You can use thinner foam for it than for the seat.

Then we attach the resulting parts to the chair frame. Your updated chair is ready. As you have seen, reupholstering a chair at home is quite feasible.

Photo of the process of reupholstering chairs

No matter how dear your furniture is, over the years it wears out and the time comes when it is no longer possible to use it. The first thing to deteriorate is the upholstery on sofas, armchairs and chairs; it not only becomes outdated and dirty, but also deteriorates. Because of their unsightly appearance, you have to part with your favorite soft chairs. If your family has antique furniture that you inherited, then there is a chance to restore it.

To reupholster chairs, you must comply with the basic requirement - to preserve wooden frame, but the final result will depend on your efforts and desires.

If the chair is not very worn and abrasions have formed in some places, then you can disassemble it - remove the back and replace the old fabric with a new one of a suitable shade. If the frame is severely damaged by bark beetles, then such a product can be restored, but the chair is unlikely to be as strong as before and over time it will still begin to deteriorate and crumble. Carpenters do not advise starting restoration of furniture damaged by grinder beetles. Individual elements can be replaced, but if the chair is badly damaged, there is no point in restoring it.

In the 60-90s of the last century, burlap, felt, cotton wool and hay were used as fillers for upholstered furniture. Even now, some furniture factories continue to use 90s technologies in production, and use plant fiber as a filler for chairs. Over several years of use, such a natural filler quickly cakes, lumps can form in places, as a result of which the upholstery fabric quickly becomes unusable.

How to choose upholstery

When choosing fabric for upholstering a chair, consider the following:

density of the material - it should hold its shape well and be durable;
the fabric should be easy to wash;
possibility to treat the surface soap solution or clean with a brush.

Popular fabrics:

jacquard – thick fabric, has good wear resistance, no puffs form on it;
chenille is a popular upholstery material for upholstered furniture. The fabric is very dense and durable;
tapestry - made of cotton, the material can be washed by hand or in a washing machine;
nubuck or artificial leather - abrasion-resistant material;
velvet, flock - durable fabric, does not fade;
leather - “breathes”, but is not resistant to mechanical damage(scratches).

How to reupholster a chair with your own hands

To ensure that the work of reupholstering a chair is completed in a short time, think in advance what materials you will need and prepare the appropriate tools.

Tools

List of materials and tools:

textile. It is best to use furniture fabrics for upholstering chairs - tapestry, flock or jacquard. They are abrasion resistant and durable. Before you go to the store to buy fabric, you need to arm yourself with a centimeter and decide on the amount of material. Take measurements of the chair seat and add another 10 cm on each side to the resulting figure. This reserve will be used for the hem, as well as for the height of the upholstery;
filler. Good recommendations received such a filler as sheet foam rubber (thickness no more than 40 mm), you can also use synthetic winterizer, batting or latex as a filler. You cannot use bulk materials (buckwheat husks, polyurethane or silicone balls) as filler for the chair seat, since the load on this part of the chair will be much higher than the load on the pillow. If you use fine filler, after a few weeks of use it will begin to crumble. If foam rubber is chosen as a filler, then its density should be from 30 to 50 kg/m3. If you use a material of a different density, the foam rubber will sag and sitting on such a chair will be uncomfortable;
thick cardboard to make a pattern;
glue and brush. It is best to buy PVA from a hardware store;
stapler and furniture staples or a cheaper option - small nails and a hammer;
screwdriver;
pliers;
tape measure and sharp scissors;
ruler, pencil, chalk or piece of soap for marking.

How to remove old fabric

Work must begin by removing the old upholstery.

How to properly remove worn fabric:

First you need to remove the seat. To do this, you need to turn the chair upside down and, in a strictly specified sequence (it is advisable to remember the order of actions, since you will then have to put the chair back together) disassemble the fasteners. First, pry up the fasteners with a screwdriver, then remove the nails, unscrew the screws and remove the metal plates. The staples can be easily pryed with a screwdriver and pulled out with pliers. If they become unusable, the staples can be thrown away and all other fasteners can be placed in a separate bag so as not to be lost.
Now you need to check the condition of the wooden frame of the chair. If it is loose, then reupholstering the furniture will not solve the main problem, appearance It will be beautiful, but sitting on a rickety chair will be unsafe. Therefore, it is first necessary to eliminate all cracks in the wood (fill with colorless sealant or glue with PVA glue), install clamps, and preferably seal the loose connections.
Now it's time to remove the old upholstery fabric. Place it on the floor plastic film or lay down old newspapers. Remove the old fabric and carefully remove all the foam. On at this stage When reupholstering chairs with your own hands, you need to decide on the measurements, so don’t rush to throw away the worn-out fabric - you can just make a pattern right away from cardboard or cut out the seat right away according to the old model. Place the old fabric on the wrong side of the new furniture fabric and trace the outline with chalk.
Now you need to put the fabric aside for a while and work on the base of the seat. Remove the remaining crumbled foam rubber that has stuck to it and remove the old glue.

Let's prepare the fabric and foam

Since it will be difficult for a beginner to reupholster a chair without a template, we’ll just start making one. You can make a template in different ways. First option: place a plywood seat on a sheet of cardboard and outline it with a pencil. Now the plywood can be removed, and in our drawing we can add 10 cm allowances on each side. Cut out the template with scissors or a sharp stationery knife. Second option: use a ready-made template and attach the old fabric to a sheet of cardboard, trace the outline with a pencil. This will be our template. Choose for yourself suitable option and make a seat template.

We have a ready-made stencil - you can cut it out of a sheet of foam rubber with a sharp knife the required part. Using the same principle, we make a fabric template: trace it along the contour and add another 10 cm on each side (it’s better to have a small supply of fabric than not have enough). We cut out the detail.

If you have chosen fabric with a pattern, then you also need to initial stage– when purchasing fabric, take this point into account and take the material with a reserve. Place the fabric with the pattern so that it is in the middle and there are no offsets. If this rule is not followed, the chair will not look presentable. Now you need to fix the fabric and mark.

In some chairs, instead of the usual plywood seat, you can see a frame made of mesh or rubber. When wicker base is normal, then nothing needs to be done; if the material has become unusable, then it must be replaced with dense, wide rubberized tapes.

How to reupholster a chair

First, glue the foam rubber to the plywood. The foam rubber is glued with PVA glue. Apply a layer of glue to the front (top) part of the plywood seat with a brush and apply foam rubber. Wait for the glue to set. Work on fabric upholstery can begin after the glue has completely dried.

When the glue dries, check again whether the foam has stuck well - if there are un-glued areas, then it is advisable to fill them with glue and wait for it to dry completely again. After which you can fix the upholstery fabric. Lay it down wrong side up, place the seat on top so that the foam is positioned “facing” the fabric. Tuck the fabric (this is extra) onto the plywood on each side. Pull the material tightly so that the fabric does not bunch up. Now take a furniture stapler and shoot the edges of the fabric to the plywood. Work sequentially, in increments of no more than 2 cm. Large folds should not form between the staples. If you see that large folds form in the places where the curves are formed, and the furniture staples do not hold them in place, then you can reinforce these places with furniture nails. Tap the nails with a hammer. Excess fabric can be trimmed off after the chair is reupholstered.

If you are reupholstering a square chair seat, then you need to put folds in the corners and direct them to the center, fold the fabric, and then attach it to the plywood.

We install the re-stretched chair seat back on the frame, first attach the plates, and then tighten the screws. Do-it-yourself chair reupholstery is complete. This is what the restored chair looks like:

How to reupholster a chair, you can watch this video:

A chair is one of the frequently used objects in everyday life, so it wears out faster than other furniture. Buying a new one (especially when the old one is important to the owner) is not necessary if the structure of the old one is intact. The bases of office and home chairs can last up to 10 years with constant use, while the upholstery will deteriorate within 3-5 years. That is why the issue of constriction is so relevant.

Used for reupholstering furniture different kinds textiles, leather or its substitute. The choice depends on individual preferences and financial resources. However, if you choose fabric upholstery, it is not necessarily cheaper than leather. For example, imported silk, brocade and some types of satin can even exceed it in cost.

Let's consider the most popular materials:

Leatherette. The most inexpensive, but at the same time the most short-lived material. As a rule, its “lifespan” is 1.5–2 years with active use of the chair. This is even less than budget options fabric upholstery. Of course, there are high-quality leatherettes, the quality of which is almost as good as natural material, but they also cost almost the same as genuine leather.
Textile. According to the increase in cost, the material can be classified as follows: chenille (fabric made from synthetic threads and cotton fibers), flock (a substitute for velvet), jacquard with an adhesive layer (smooth, durable and dense fabric, has water-repellent properties, characterized by a mixed composition of threads), microfiber ( the texture is similar to suede) and tapestry (dense, thick fabric). Such wide choose helps you find upholstery textiles that fully suit both your needs and financial capabilities.
Genuine Leather. The most expensive, prestigious and quality material. However, it is worth considering that working with genuine leather requires special equipment and skills, so the cost of reupholstery should include not only the price of the material itself, but also the costs of necessary tools.

When choosing leather, pay attention to its thickness. If you choose leather thicker than 3 mm, it will be difficult to work with due to the lack of elasticity. It is most convenient to use a material whose thickness is no more than 1.5 mm for upholstering a chair.

To upholster an armchair or bar stool, it is recommended to use genuine leather or thick textiles. It is better to attach the material to the base using construction stapler or glue. The process will take no more than 15–20 minutes (with a certain skill).

To qualitatively update the genuine leather upholstery on a chair, you will need the help of professionals.

As for a leather piece of furniture, in this case the work will take much more time and effort. The fact is that the “executive chair” is more difficult to disassemble and assemble. In addition, often reupholstering leather furniture involves removing old upholstery and cutting out new upholstery, which is fraught with some difficulties and will require certain skills. To avoid possible breakdowns or other troubles, it is better to entrust the work with such an item to professionals.

We suggest that you familiarize yourself with the most in a simple way furniture updates. We are talking about upholstery with artificial Alcantara.

Alcantara chair upholstery

Self-adhesive Alcantara is an artificial suede equipped with an adhesive layer. Its service life is 3–7 years. Despite the low stretch coefficient, the elasticity of this material is sufficient to make it comfortable to work with when restoring furniture. It fits well on surfaces and takes their shape.

Please note that real self-adhesive Alcantara must have the words “Made in Korea” on it. back side and a lined cage with 5 cm squares.

Tools and materials

We will be reupholstering a Chinese-made office chair. For this we need:

Necessary calculations

To avoid unnecessary production waste, it is important to correct calculation materials. Use a measuring tape to measure all parts of the chair. We will work with back cover, the back of the chair and the seat, and in our case the dimensions are:

53 cm - cover;
53 cm – back;
45 cm – seat.

Please note that to securely fasten the new upholstery you will need to make allowances of 5 cm on each side. If you make more, it doesn’t matter, the extra parts can be cut off with a stationery knife.

We bought 1 each for work linear meter beige Alcantara and white, of which we needed:

50 cm of beige fabric on the seat;
58 cm of beige fabric on the back;
58 cm of fabric per cover.

Preparatory work

We will work with all the parts separately, so the chair will need to be disassembled using pliers for the nuts. As a rule, all parts can be easily unscrewed, some even by hand. The process takes no more than 5 minutes.

Then we start preparing the fabric. We take Alcantara beige colour, which we will need to reupholster the back and seat. Using a marker and ruler along the back of the fabric, measure out the required dimensions for different parts and cut with scissors. We do the same with the white fabric for the lid.

There is no need to remove the current upholstery, as Alcantara fits perfectly over old textiles.

Master class on updating a piece of furniture with your own hands

Once the preparation is completed, you can proceed directly to the reupholstering process. Let's start from the back of the chair:

Alcantara glues quickly and firmly, so all excess must be cut off immediately - after an hour the material sticks so that it will be impossible to peel it off and carry out any manipulations.

Now we work with the seat:

The work is done easily and quickly, the whole process takes about 40 minutes.

The simplest and economical way update an old and inconspicuous chair - reupholster it with bright modern upholstery with your own hands. This way you can easily change the interior of the room, show your creativity and do everything to your liking.

Where to begin

First, you need to get rid of the old upholstery and filling once and for all. Only the springs, if any, should remain.

Secondly, carefully inspect the product to be remade. Its frame must be strong and stable, otherwise all the work will be done in vain. It is recommended that along with changing the upholstery fabric, you also change the entire chair.

To do this, you need to sand the surface to eliminate all scratches and unevenness, rinse the product thoroughly, tighten up loose parts, replace fittings, apply a primer (putty or white paint), paint and seal the result with varnish.

Thirdly, all the necessary tools and materials are prepared, which include:

Fabric for reupholstery;
Seat filler;
PVA glue;
Centimeter or long ruler;
Cardboard pattern or plywood base for seating;
Furniture stapler or small nails;
Screwdriver, screws;
Scissors or stationery knife;
Pencil, soap or crayons (for measuring fabric).

An important point is the choice of suitable upholstery for upholstering the chair, which should be as dense and strong as possible. Also, the upholstery fabric should be easy to clean from dirt. various kinds using a sponge or brush.

So, you can choose from tapestry, wool, chenille, artificial and natural leather, jacquard, satin. The required size is calculated by the formula: area of the upholstered area + 15-20 cm around the entire perimeter on the bends.

As for the filler, it should have a density of 30-50 kg/m3 and a thickness of at least 4 cm. Foam rubber, a soft, durable, non-creasing and non-deformable material, is considered optimal. Sheet polyurethane foam and latex are also used.

Batting and padding polyester are used extremely rarely, as they do not hold their shape and quickly sag. Under no circumstances should you stuff the seat. bulk materials(polyurethane balls, buckwheat husks and others).

How to decide on color

It is important to carefully approach the choice of shade and texture of the future product. Here photographs of chairs from furniture catalogs, where you can find hundreds of upholstery options, will help you in your search. You also shouldn’t lose sight of your own wishes, the interior of the room, and the design of other pieces of furniture.

The color of the upholstery of a restored chair is usually dark. The most commonly chosen colors are brown, blue and burgundy. However, for light frames, golden fabric is selected, beige tone. Often preference is given to more intense colors, especially if the furniture is intended for children's rooms or living rooms in the pop art or city style.

An interesting solution would be to use several materials on one product: for fabric mosaics in one place or for upholstering different areas of a chair.

Constriction algorithm

When the frame is prepared and the color is chosen, the actual reupholstery begins. In general, the procedure is as follows:

Remove old upholstery.
Make the necessary repairs to the frame.
Cut out the pieces using plywood base for seating or old upholstery.
If there are springs on the chair, then they must be tied vertically, horizontally and diagonally with a strong rope, making 8 knots on each spring.
Place a piece of burlap over the springs to reduce the mechanical impact of metal objects.
Cut out the filling and fabric using scissors or a utility knife. Pay close attention to the existing print: the pattern, stripes or ornament must match.
Install and glue the filler. Fold the edges over the frame and secure with staples. Remove excess.
Place the fabric on the workpiece, stretch it and secure it with a stapler. Work begins from the central part and continues along the entire perimeter. The step between staples should be 1-2 cm.
Additionally, secure the upholstery with small nails. You can hide staples or nail heads with decorative elements.
Cut off excess pieces of fabric.
Coat the product protective coating: Sprinkle with a special spray and leave in a ventilated area for several hours.
Install the seat into place using a screwdriver and screws.
Glue a thin black fabric underneath the seat to give the chair a finished look.
If necessary, repeat the steps to reupholster the upholstery of the back and armrests of the chair.

It is not difficult to reupholster a chair with new upholstery fabric yourself. The proposed algorithm will help even a novice master cope with the task.

Another way to tighten the fabric sequentially is to fasten the staples in the middle of each side, starting from opposite sides. Then the seat rotates, and the fabric is fixed further in a similar way, gradually shifting in one direction or the other.
Springs are much more durable than upholstery fabric, so there is no need to remove the metal filling.
The seat for a chair without springs can be leather straps stretched in strips or crosswise.
Threaded fittings should not peek out from under the upholstery, but they should also not be covered with too thick a layer of fabric.
The stapler must have enough power to penetrate the wood.
If you buy more fabric than you need to cover an upholstered chair, you can make additional pillows or bolsters to match the item.
Rapid wear of the fabric from the edges will prevent special tape, pasted on dangerous areas.

The main advice is not to be afraid to experiment with patterns, colors and textures.

You can always put your favorite silk or soft velor of the most intense and enchanting colors on top of a dense material, and the frame of the chair can be decorated with fabric scraps or amazing paintings.

You cannot say goodbye to a chair with worn or torn upholstery right away, since a strong and stable frame can last for many years. New finish is able to give furniture a second life, refreshing the familiar interior without high costs.

To do this, just think about the design of the chair, choose the fabric for the upholstery, prepare the necessary tools and get to work in a creative mood.