Contents:
In a well-equipped carpentry workshop, set up in a country house or in a private house, it is necessary to have a circular disk mechanism that allows processing wood blanks.
Very often used as household woodworking equipment homemade machine, made on the basis of hand circular saw or cutting tool with independent electric drive.
To place any of these mechanisms, you need a specially equipped table with a surface that makes it easy to work with wood workpieces.
Depending on the type of cutting tool, as well as on the material used to manufacture the frame, the table for a circular saw can have the following designs:
- firstly, it can be made in the form of a workbench with legs and with a hand-held circular saw attached to it (a lightweight version);
- secondly, it can be equipped cutting disc design mounted on a metal frame. The drive part of such a machine, consisting of an electric motor and control circuits, is located in the lower part of the frame (capital version).
Making a table for a circular saw is within the capabilities of every craftsman.
Design selection
Before you make a table for a circular saw with your own hands, first of all, you need to decide on its design. Thus, a lightweight version based on plywood and beams must contain the following mandatory elements:
tabletop directly;
plywood body;
Support legs provide good stability
The capital structure must include the following components:
bed based metal profiles or corners;
upper and lower brackets necessary to accommodate the cutting blade with shaft and drive equipment, respectively;
the table itself with a slot for the cutting blade, mounted directly on a metal frame.
The most accessible for production in living conditions is considered a wooden table for circular saw(i.e. lightweight design).
A lightweight version of a circular saw table would look something like this
Preparation of sketch, material and tools
As an example, consider the manufacturing procedure wooden workbench approximately 100 - 120 cm high. Before making such a table with your own hands, it is advisable to prepare a small sketch in which the structure of the future structure will be displayed, indicating the dimensions of its main elements.
The exact height of the table is set taking into account the height of the master working on the machine (the location of the working plane at the level of the person’s hips is considered comfortable).
On preparatory stage You should also decide on the material for the manufacture of the future structure, which, as a rule, is made from beams and multi-layer plywood 28 mm thick.
In order to make such a table with your own hands you will need the following blanks:
- metal sheet of suitable size;
- standard sheet of thick plywood;
- metal square pipe, from which the guides are made;
- a set of clamps in the amount of two pieces.
To assemble the table, you also need a tool set of the following items:
- screwdriver and electric drill;
- jigsaw or regular wood saw;
- square, tape measure, ruler (for current measurements);
- manual frezer
Video: Making a table for a circular saw
Making a table cover
The manufacturing procedure for this structural element involves the following operations:
Work begins with marking and cutting out a piece of plywood, the dimensions of which must correspond to the dimensions of the prepared iron sheet.
After adjusting to size, the surface of the workpiece is carefully sanded using emery cloth.
Then, on the lower surface of the plywood sheet, fixation points for the actuator are marked while simultaneously marking the slot for the cutting disc.
To do this, you should first try on the soleplate of the circular saw you are using at the installation site. In this case, it is most convenient to simply remove the disk from it and determine the exact location of the landing points.
Before installing it at the mounting location, an additional check is made to ensure that the slot for the cutting blade is correctly marked.
Marking the table top is done directly along the sole of the circular saw
At the final stage working surface it is closed with a steel sheet with two guides, which is then fixed with ordinary self-tapping screws.
Subsequently, along the guides, it will be possible to make special markings from the corners, increasing the convenience of processing wood material.
Additional information: To arrange the operating surface of the table, in addition to plywood, plexiglass or fiberglass can be used.
Assembling the frame with legs
The base or frame of the table is assembled from a set of transverse and longitudinal wooden beams, which are attached to the bottom of its cover, increasing the rigidity of the entire structure as a whole. For this, four bars with a cross section of 50x50 mm, placed at a distance of about 7-9 cm from the edge of the table, are sufficient.
They are fixed on the bottom of the lid with self-tapping screws of suitable size in increments of approximately 23-25 cm. On its front side, the fastening elements are recessed into a material that completely hides their caps.
The frame can be made stronger by pre-treating the mating surface of the bars with a layer of wood glue, carried out immediately before attaching them. After joining the glue-coated workpieces, the latter are securely fixed with clamps, which are removed immediately after the adhesive has dried. The legs of the structure can be made from bars of the same cross-section as the blanks for the frame (50x50 mm).
The structure of the table must be strong and rigid
The shape of the legs is chosen so that they provide maximum support area for the frame part of the base and have a shape that tapers towards the flooring. On one of these legs, controls for turning the circular saw on and off are subsequently placed, duplicating the buttons located on its body.
You will be able to further increase the rigidity and stability of the entire structure with the help of a set of steel angles mounted in the area of its butt joints. To secure them, it is recommended to use standard bolts with washers, which should preferably be installed with their heads facing outward.
Features of manufacturing a metal frame (bed)
The upper part of the metal base is a welded frame measuring 800x800 mm with legs made of pipes 220 mm long and a cross-section of approximately 17-20 mm welded at the corners.
Two longitudinal profiles are mounted on a frame made of 25 mm angles, used to install the shaft on bearings.
The lower part of the frame is welded from corners to ensure greater stability of the structure bigger size(40 mm) and has two jumpers designed for mounting the electric motor with starting equipment circuits. Pipes are also welded at its corners, having the same length as on the upper frame, but slightly larger in diameter (23-25mm).
Closer to the edge of such pipe legs, threaded holes are prepared in which special holders are located (they are also called “lambs”). With the help of these wings it will be possible to fix the position of the pipes of the upper part of the frame, which is moved to regulate the tension of the drive belt.
Expansion of functionality
In conclusion, let’s touch on the topic of expanding the functionality of the products you manufacture. working structure. If there is free space on the operating surface, additional woodworking equipment can be mounted ( electric plane or a router, for example). Having a plane and a wood router will allow you to expand the functionality of the machine and turn it into a full-fledged woodworking center.
In addition to this, such a milling cutter can be equipped with a special mechanism for adjusting the position of its working part, which can be changed within specified limits (the so-called elevator).
Video: Saw table dimensions
A circular saw is a productive, convenient and maneuverable tool with which various construction and Finishing work. If it is necessary to perform large volumes of tasks, work with manual circular saw pretty hard. In such situations, a circular saw table becomes an excellent assistant. You can assemble it yourself from boards and plywood. The saw itself will be placed at the bottom of the tabletop, and the toothed blade will fit into the slot. The saw turns on, the disk begins to rotate, lumber is fed and sawing occurs. If desired, you can collect great table for a circular saw with your own hands. There is nothing complicated in this work.
It is difficult to work with large volumes of wood with a regular circular saw, so it is better to place it on a table.
Circular saw table design
Before collecting circular table with your own hands, you need to carefully consider its design. At this stage, your task comes down, first of all, to calculating the load that will be placed on the table in the future. When assembling a saw table with your own hands, consider the power of the unit. Thus, for high-power industrial tools, it is recommended to use a reinforced steel welded structure. In the case of a home saw, the device is so powerful design not necessary. It will be enough to assemble a saw table with your own hands from boards and plywood.
When planning to make a saw table with your own hands, you need, as already noted, to take into account the power of the tool. In home workshops, saws with a power of up to 800 W are most often used. At the same time, it is necessary to take into account the frequency and volume of work performed. For example, when building a house you will have to cut much more material than under any other conditions. Experts do not advise buying saws more powerful than 1200 W for your home. In the case of a home workshop, this simply does not make sense.
The higher the power of the circular saw and the higher the volume of work performed, the more reliable, durable and stable the table you create should be. Professional-grade circular saws are installed on bases made of metal profiles. In some cases, such tables are even embedded in the floor, since vibration may cause the operator to briefly lose control of the saw, which will be enough to cause injury. Creating such a table requires certain skills in working with special tools, welding, etc. Assembling a regular one wooden table For home saw accessible to almost every person, even if he does not have such experience.
Preparing to assemble the table
Table assembly diagram.
The most simple option The table for the circular table is a structure made of fairly thick plywood and boards. In this case, plywood will be used to make the countertop. The tabletop itself will be stationary. The tool needs to be installed under it. First, a slot is created in the lid along which the saw blade will move.
Choose the dimensions of the table, first of all, based on yourself. You should be comfortable and comfortable working. The instructions cover the average and most common sizes. You can change them at your discretion. The height of the table is 1-1.15 m. Choose the length taking into account the nature of future work. If you often cut long boards, the table top should also be made long enough. If the length of the table top is more than 2 m, it is recommended to equip the structure with an additional pair support legs. Without them, the table will vibrate strongly.
The thickness of the plywood used to make the tabletop should be from 5 cm. Plexiglas and fiberglass are suitable for the same purpose. From use Chipboard master It is recommended to refrain due to the insufficiently high strength of the material.
The lid is polished and varnished in several layers. Thanks to this, the required sliding of the processed materials will be ensured. The best option is a reinforcement on the countertop metal sheet. This will increase the reliability of the surface and extend the service life of the product as a whole.
Materials and tools for work
A table for a circular saw requires the presence of guides, which will ensure higher accuracy in cutting materials. The guides are made from a metal corner. Clamps are usually used to secure them to the tabletop. It is not recommended to make the guides stationary. It will be more convenient if you can change their position in the future.
Prepare materials for self-assembly of the table:
- Plywood. If you wish, you can use a different material for the countertop.
- A metal sheet.
- Beam 50x50 mm.
- Board 50x100 mm.
- Clamps in the amount of 2 pcs.
- Metal corner for making guides.
Pre-gather all the necessary tools:
- Hacksaw. If possible, it is better to use a jigsaw instead.
- Screwdriver.
- Electric drill.
- Hand cutter or machine. If you don't have them, you can do without them.
- Tape measure and ruler for measurements.
- Square.
After preparing all the tools and materials, you can begin assembling your homemade table. Some craftsmen use old dining and kitchen tables. But you shouldn’t count on great durability of such products. It’s better to do everything yourself, “from scratch.” This way you can assemble a comfortable table that fully meets your needs and requirements.
Step-by-step instructions for assembling the table
Table circular saw from steel plate.
First you need to form the tabletop. Take plywood sheet and make the markings. The edges of the sheet should match the two edges of the lid. Cut out the workpiece with a hacksaw or jigsaw. If desired, process the cuts with a router. This is optional, so you can skip it. this stage. In the case of a circular saw table, reliability is more important than good looks. appearance.Roughly sand the countertop using sandpaper.
At the bottom, prepare a slot for the disk. Measure the circular saw blade. To make it as convenient as possible, remove the saw blade from the tool and simply circle the required part of the saw.
After completion of the arrangement seat try on the slab and make the required adjustments. Mark the slot locations for saw blade and fasteners. If the disc must be raised and lowered, the table must be equipped pendulum mechanism. In this case, the shape of the slot should look like a truncated pyramid. The top of this kind of pyramid needs to be directed downwards. To make the frame of the lifting mechanism, it is better to use metal corners welded to each other.
Assembling the frame and installing the legs
Table guide carriage for circular saw.
Next you need to make markings for the transverse and longitudinal slats. In the case of such a table, they act as stiffeners. Do it with wrong side. The planks are made from timber. You need to prepare 2 longitudinal ribs. Select the length based on the length of the tabletop. It is enough to simply subtract 8-10 cm from it on each side. There should also be 2 transverse strips. To determine their length, subtract 8-10 cm from the width of the tabletop on each side.
Prepare sockets for self-tapping screws. The slats are fixed so that the lid protrudes about 8-10 cm beyond the edges of the frame. It is important to make the most reliable and durable fastening. Install the first self-tapping screw at a distance of 4-5 cm from the edge of the rail. The screws themselves are mounted in increments of 20-22 cm. The parts must be drilled through. The screw heads must be completely recessed into the tabletop material.
The transverse ribs are attached first. To ensure maximum reliability of the table, you must first coat the edges of the slats with wood glue. Tighten the structure with clamps and secure with self-tapping screws. Leave the table cover until completely dry, then install the longitudinal slats in the same way. Pull together the frame parts and install several fasteners on each side. After this you can remove the clamps.
To make the legs, use bars. The height of these elements is selected individually in accordance with the height of the operator. It is more convenient when the tabletop is located at hip level. Before installing the legs, plan them on one side so that the processed side goes to the corner. As a result, the base of the leg will have a slightly larger area than the top.
It is best to use metal corners to secure the legs. You need to slightly press them in so that the base of the homemade table is positioned at odds. Thanks to this, the bed will become more stable. Fastening is done using bolts and washers. They need to be installed with their caps facing outwards. If installed differently, you may be injured by protruding fasteners during operation.
This will make the design even more reliable. The slats should be installed in pairs on the sides of the homemade table.
Thoroughly polish the surface of the countertop and cover it with several layers of varnish. Instead, you can use small screws to secure a smooth metal sheet.
Finally, the circular saw is installed in its intended place. Additionally, you can apply markings to the surface of the countertop, which will contribute to a more even and correct processing sawn material.
The control elements of such a machine must be placed on the outside of the tabletop. Usually they are fixed on some table leg. Completing this step of the job requires some electrical installation skills. If they are absent, it is recommended to contact an appropriate specialist.
Thus, in self-assembly table for a circular saw there is nothing complicated. This does not require much time or money. You will spend much less on materials than on a ready-made factory table, and the quality of the product, if you follow the instructions, will be no worse. Good luck!
It is a convenient and productive tool that is used to carry out construction work. Using this equipment, you have the opportunity to use the qualities of maneuverability, as well as speed. However, when cutting large quantities of lumber, working with this tool is quite difficult. The table greatly simplifies the task; it can be made without much difficulty.
Execution Features
The structure can be based on plywood or board. The tool will need to be installed at the bottom of the tabletop, while the toothed disk will need to be located in the hole in the worktable. The element used for cutting will extend beyond the rectangular hole.
After the saw is turned on, the disk will begin to rotate, and as the material is fed, sawing will begin to occur. The maximum thickness of the material being processed will depend on the dimensions of the disk, as well as the power of the tool. When choosing equipment, you need to take into account the thickness of the table top to which the saw will be attached at the bottom.
Features of choosing a "circular"
If you do not yet have a circular saw, then you can purchase one, taking into account some characteristics, among which is the power of the equipment. If the tool is intended to be used for everyday tasks, then a power of 800 watts will be enough to make a table for a circular saw with your own hands. This indicates that the volume of work will be average.
It is important to pay attention to the depth of the cut; the maximum thickness of the material being processed will depend on this. Hand saws of semi-professional or professional class, as a rule, have a cutting depth ranging from 40 to 70 mm.
Work technology
Holes in the surface of the desktop must be drilled through the markings. When making a table for a circular saw, marking must be done before cutting. The ribs are fixed to the tabletop using elements that, after connection, must be compressed with clamps. You need to mark the location of the side stiffening ribs, which then need to be sawed and glued in a similar way.
Features of the work
If you decide to make a table for a circular saw with your own hands, you can prepare the drawings yourself. After gluing, the clamps should not be removed immediately; the structure must be additionally secured using self-tapping screws that are installed in the holes. They need to be prepared from the bottom side so that the fastener heads are recessed into the structure. After the glue has dried, the stiffening ribs can be removed from the clamps. At this point we can assume that the tabletop is ready.
A do-it-yourself table for a circular saw should be made using legs, which should be made of 50x100 millimeter boards. The height of these elements will be determined by the height of the master; as a rule, this parameter is 110 cm. The board must be cut along the axis at a slight angle on one side. Next, the blank is applied to the tabletop so that when installing the legs, they are somewhat spaced. These elements must be fastened from the outside of the stiffeners; it is recommended to use bolts.
When making a table for a circular saw with your own hands, a photo of which can be viewed in advance, you need to try to increase the stability of the structure in parallel with attaching the legs. To do this, you can make a screed, which is made from a bar with a cross-section of 50x50 millimeters. The hand-held circular saw should be installed in the prepared groove on the underside of the work surface. The sole should be bolted and the toothed disk should be installed in the slot. Markings can be applied to the table, which will make cutting materials much easier.
To protect it from moisture, the table surface itself can be coated with varnish, which is applied in several layers. When making a table for a circular saw, after applying the first layer, you must wait for it to dry completely, only then can you begin to cover the surface with another layer. This approach will eliminate the effect of lumber sliding on the working surface.
Turning the saw on and off
When making a table saw table with your own hands, you should: last stage solve one important issue. It consists of the task of turning the saw on and off. If the master has a sufficient amount of experience and knowledge in electrical engineering, then he can bypass the power key, and then move the control buttons to the outer surface of the stiffener, which is located in front. If this scheme turns out to be too complicated for you, then it will be enough to tighten the key using wire. But you can turn the saw on and off using the power cord.
in the form of a trolley
If you want to make the table mobile, then its upper part can be made in the form of a trolley. Laminated chipboard can be used as its side walls, which will be located at the back and front; its thickness can be equal to 16 millimeters. The legs of the table will be bars, the cross-section of which is 50x50 millimeters. The supports for the wheels of the structure will be made of boards, the thickness of which is 35 millimeters. In order to increase the quality of the table's rigidity, the back and front walls need to be reinforced with a board whose thickness is 20 millimeters. All parts must be assembled using self-tapping screws and additional PVA glue. The support boards for the wheels must be secured with metal squares.
For attaching the trolley to support boards you need to make shallow recesses, the radius of which will be equal to the radius of the wheel. To attach ladders to the surface of the table, you need to install two elements in the form of inserts, which must be mounted on a single plate. At this point, we can consider that the table for the circular saw has been made with our own hands, and you can begin to use it in tandem with the main tool, which every home craftsman who loves to work with wood has needed at least once.
Finally
If you decide to make a table for a circular saw with your own hands (DP 2000) using this technology, then the work process will not be accompanied by unnecessary difficulties. Anyone can handle this House master, even one who does not have specific skills in conducting this type of work. If you want to significantly expand the functionality of a workbench designed for a circular saw, then you can increase its safety rating. You can make the design more complex, it all depends on your skills, and most importantly, your desire to explore new horizons in construction work. Good luck to you and successful new decisions!
Most people who work professionally with wood would like to have everything at their disposal necessary machines. But unfortunately, this is not always possible. Some people don't have the space to do it, others, and I think the majority, it's money. Any, even the most primitive machine is quite expensive.
But what’s stopping you from just doing it yourself? Nothing is impossible for a person with intelligence. For every carpenter, a circular saw is the main tool. But it happens that only a hand saw is available, and this is not always convenient for large volumes of work. In order not to purchase a separate tool, you can make a stationary mini saw yourself for ease of work - make a sawing table (stand) for it.
Table saw
When choosing a circular saw, you need to be guided by the following characteristics:
- Saw power. If the amount of work is quite large, it is advisable to take a tool with a power of at least 1.2 kW.
- Cutting depth. The thickness of the material to be processed depends on this parameter. U hand saws this is 40–70 mm. But when installing it in a table there will be a decrease of around 10 mm.
- Button placement. The design of the sawing table must provide free and safe access to all control buttons, otherwise it will be necessary to modify the control system yourself.
- Rotational speed. For cutting wood, high rotation speed is preferred. This affects the cutting quality. For plastic, for example, this is not very good. Due to the high rotation speed of the circle, the plastic heats up. You need to choose average characteristics. 3-4 thousand rpm will be enough.
Do-it-yourself table for a circular saw, installation, fastening
To make the saw table itself, you will need to acquire materials that are sold at any hardware store.
We will need:
- plywood 15–20 mm thick;
- timber 50*50 mm;
- boards, approximately 50*100 mm;
- switch;
- socket;
- self-tapping screws;
- PVA glue;
- rollers;
- metal corners.
Making a workbench
- Mark and cut a tabletop of the required size from plywood. Clear sandpaper surface.
- At the bottom of the tabletop we mark places for holes for attaching the saw. To do this, you need to remove the blade and install the saw in the right place, making notes. The holes for the bolts are countersunk on the surface, and the heads of the bolts need to be sanded.
- If the material will be cut at different angles, the hole for the disk should be made in the shape of an inverted trapezoid.
- Mark the places where the stiffening ribs are attached to the tabletop (from below, at a distance of about 8 cm from the edge). The legs need to be secured to the ribs. The ribs are screwed on with self-tapping screws at intervals of 25 cm and glued with PVA.
- The legs are made from timber 100 cm long. Then a screed is made from timber for additional strength.
- To be able to adjust the height of the table legs, nuts and M14 bolts are attached from below.
- We fix the saw from below.
- We attach the socket to the inside of the table. From it we pull the wire to the switch.
- We make a parallel emphasis. We cut two strips of plywood, the same length as the width of the table. The width of the stripes is 10 cm. We make the corners round. We sand both strips and fasten them with self-tapping screws. Then we cut two strips of the same length, but three times wider. We fasten them. This will be the guide. We fasten the stop and guide. We set a right angle relative to the disk. We attach the rollers.
Table drawings for a circular saw
There are other ways to make a stand for a hand-held circular saw with your own hands. Here are two more examples.
Table for hand-held circular saw with lifting mechanism
To change the depth of the cut, you can additionally install a lifting mechanism (elevator).
Myself lifting mechanism We mount it from a metal sheet that is attached to the frame on the machine. Lifting will take place along the guides by tightening the bolts.
One way is to install the adjusting rod with fixation nuts. Instead of rods, we use studs. The adjustment handle is made from a plate welded to the end of the stud. At a distance of 4–5 mm from the center we make holes for self-tapping screws. We weld a rod to the edge of the plate, which we will use to rotate the structure.
Conclusion
From the experience of many people, we can say that although such machines do not look very attractive, with the right and diligent approach, they are no worse than factory ones, such as Interskol, and have no less service life. The big advantage is that the cost of such a machine will be three times lower. In addition, you can make a machine “to suit yourself,” which will greatly increase labor productivity.
Many woodworkers have a large number of different saws. Some can work without additional accessories, but the circular one will be difficult to use manually. A table for a hand-held circular saw made by yourself is quite real way save money cash and ensure comfortable cutting large quantity materials. Moreover, it is not difficult to do it, the main thing is to draw up the drawings correctly and provide yourself with the necessary tools.
A do-it-yourself circular table made from a hand-held circular saw will provide comfort when cutting, as it will be made based on your wishes. The working surface will convenient size, which is difficult to find in a store where there are mostly standard countertops. Moreover, there are situations when the need for a router table arises unexpectedly and the purchase option is completely eliminated. Don’t despair, using the advice of skilled carpenters, you can create a model that will be no worse than the store-bought version.
1
2
3
Features of a circular saw table
Making a table for a circular saw with your own hands is very simple, especially if you have at least a little experience in carpentry. Experienced craftsmen can assemble it even without diagrams. The design consists of two main parts:
- legs;
- smooth working surface (table top).
Additional departments in the form of drawers are not required, but such projects can be created if desired.
1
2
Remember that the saw itself must be securely fastened under the table, and only the blade remains on the surface. The hole in the table for the circular saw should be several centimeters larger than the blade so that sawdust can easily fly down without clogging the mechanisms.
Table for miter saw you need to make it as durable as possible with your own hands. Since the greater the power of the tool, the greater the load will fall on the surface. Be sure to take this fact into account when choosing the material and location for its installation. Knowing how to make a table for a circular saw, you can save a lot of money and enjoy more convenient use of the tool.
Inventory and work process requirements
What a table for a miter saw should be like with your own hands is, of course, decided by the master himself. TO mandatory requirements can be attributed:
- safe and durable fastening of the saw;
- flat and smooth working surface of the tabletop;
- Easy access to start and stop buttons.
A homemade table can be made from wood
The stores mainly offer products from of stainless steel. But tables for routers and circular saws made of wood are in no way inferior to them in quality, and the service life of the material is not reduced.
You can make a table for a hand-held circular saw with your own hands using the following tools:
- boards for legs and tabletops;
- wood glue;
- screws and screwdriver;
- jigsaw;
- plane.
In addition, you need a tape measure and a pencil, as well as wood varnish for protective properties.
Stages of work
A circular saw is a rather dangerous tool. The sawing table should be positioned so that the saw is exactly in the center, without shifting the center of gravity. Based on the drawn up diagrams, markings are made on the board with a pencil, and then the base is cut out with a jigsaw. After this, the resulting tabletop must be carefully sanded to make it smooth.
After the work has been done, the tabletop is turned over and inside Markings are applied to make a recess under the sole of the circular saw. The recesses are created using a milling cutter. The saw is installed in homemade table, carefully attached and tested for strength.
When making a table for a circular saw with your own hands, do not forget about the stiffeners. They significantly strengthen the structure, especially in combination with self-tapping screws.
The legs for the manual circular saw are attached last. The dimensions, as well as the height, depend on the craftsman; the main thing is to fasten them well with bolts and screws. They need to be placed slightly apart, and the strength should be controlled using the same stiffening ribs.
Working with electronics
Making a table for a circular table with your own hands using standard drawings is quite simple, but you definitely need to take care of the power supply. If the master is well versed in electronics, then the best option will bypass the start and stop buttons, and secure them in convenient location. A more simplified option is to tighten the start button of the circular saw and turn it on using the power cord. But this method is not very safe, since emergency situation the equipment will not be able to turn off automatically.
Safety at work
Remember that there should be no foreign objects on the table on which the cutting takes place. If a DIY circular saw becomes unbalanced, the problem should be corrected immediately.
For safety, be sure to wear safety glasses
Can't be held wood material close to the saw blade, it is unsafe. Be sure to wear protective clothing, goggles and gloves for work. Remember that it is not enough to make a circular table with your own hands, you also need to monitor its condition in order to be safe.
