Having at least a small plot of land in use, I want it to bring pleasure. small pond from car tire and how to do it, read the information below. Such a pond will be a joy to everyone. And there is not much work with him, and the pleasure is great. If in the garden or personal plot there is a corner of wildlife that attracts insects, birds, and people, it brings joy. In a review article about ponds, you can find out the varieties of such structures. In this article, you will learn how you can make such a beautiful pond at low cost.
For this you will need:
1. Worn tire from truck, wide profile. Or you can use a tire from a large tractor.
2. Thick polyethylene film, rubberized fabric for laying on the bottom and sides of the tire.
3. Gravel, sand and decorative stones.
4. Tools for work: a shovel, a grinder or an electric jigsaw.
If the materials are prepared, I propose to start work.
You can start digging a shallow hole, so that the edges of the tire are 10 centimeters above ground level. At the bottom of the pit, it is desirable to make a pillow of compacted sand 5-7 centimeters thick.
Next, the tire is laid and the upper part is cut out using a grinder or an electric jigsaw. The tire must be overlaid on all sides with earth or sand so that there is no empty space between the tire and the walls of the pit.
Then a waterproof material is laid that is larger than the diameter of the tire. The material must extend beyond the edges of the tire to secure it to the ground.
After that, it is necessary to cover the film or material with a layer of sand, then with gravel, and already upper layer must be laid with a decorative stone.
I do not advise making the construction capital using cement mortar, since in the cold season the film or fabric will fail and it will be difficult to replace it. So it happened with us, after the winter we poured water into the pond and saw that the rubberized fabric had leaked. And I had to replace it.
The New Year and other winter holidays are just around the corner, but you can still have time to buy something on the Chinese website to make your home festive and cozy. We have made for you a top selection of popular jewelry and other products that you can’t do without this holidays. Let's see what interesting products this year can be ordered on the Aliexpress website.
Receive one of the most read articles by email once a day. Join us on Facebook and VKontakte.
And it's not a joke. We are talking about old tires that can be found anywhere, even on the way to the country. According to the latest research, about 300 million of them are thrown out worldwide every year! Therefore, if you decide to make an original reservoir of discarded tires on your site, you will not only get a fantastic place to relax, but also help save the environment.
There is no person who would not dream of having a summer house with a view of the sea or a lake, but such happiness is not available to everyone, but everyone can build their own reservoir.
Let's see what is needed to create such a pond.
So, we need:
One or more tires (it is better to use tractor or KAMAZ tires);
waterproofing material, PVC material (ordinary film will quickly fail);
sand, gravel and pebbles;
shovel;
stones various shapes and size;
jigsaw or saw.
Once all the materials and tools are collected, you can start creating your own piece of paradise. First, decide on its location. Ponds are best placed in the shade of the terrace, it looks very beautiful and tempting when you drink tea or coffee on it in the early morning. If there is none, then it is possible under the crowns of trees, in order to avoid excessive heating of the water, suddenly you are lit up with the desire to launch fish and frogs there.
Think about how you want to decorate the edges of your tiny lake. Will it rise or make it level with the ground. This nuance must be taken into account in order to determine the depth of the pit.
Another important issue is water supply and drainage. You must understand that an artificial reservoir requires permanent care, otherwise after a while it will turn into a fetid swamp. For your own convenience, it is better to supply water with communications as expected than to use irrigation hoses, and also consider a drainage system so as not to drown in the mud near it.
Now you can start working:
We dig a fairly large and deep hole so that our tire freely enters it. The gap between your structure and the ground should be at least 30 centimeters wide, this will make it possible to securely fix the waterproofing material and fix the tires in the pit. We level the bottom well and tamp the soil.
With an electric jigsaw (this is the safest tool for this kind of work), very carefully and accurately cut off the top of the tire. If there is no such tool, then you can use a metal saw, but it will be too long and tedious.
We lower the tire to the bottom of the pit and set it so that it is in the center and there are no distortions, for this it is better to use a level. We fall asleep to the very bottom with a layer of rubble or small pebbles, then with sand, creating a so-called pillow. Its thickness should completely cover the ground.
Cut out (with a margin of 50-60 cm) right size hydro insulating material, in our case, a PVC sheet and carefully distribute it along the bottom and inner walls of the tire, without stretching, but simply repeating the shape of the tire. We carefully fill the hanging edges of the canvas behind the outer walls of the tire, fix it with stones in several places.
We proceed to compaction, filling up the gap remaining between the outer walls and the pit. For this, it is better to use earth with sand. Each layer must be thoroughly filled with water to fill all the cracks. Such a move will give the structure stability and safety when filled with water or physical impact.
And who knows, suddenly your baby or four-legged pet will decide to swim in this lake.
At the bottom of an already formed reservoir, we pour a layer of sand, followed by gravel, and then beautiful river pebbles - this will create the illusion of a real bottom.
We will supply water and make drainage. To do this, you will need to lay pipes and install a faucet. To prevent water from accumulating around the lake, make a nearby drainage pit, which simply fill with gravel or expanded clay and you will never have dirt under your feet.
We form the edge of the created lake, lay out the stones as densely as possible to each other. If there are small children, then it is better to do it with pebbles to avoid unnecessary injuries.
We fill our pond with water and start decorating with plants or populating it with fish, newts and frogs. And also we draw up a zone around our unusual reservoir. Here your creative fuse can create extraordinary miracles.
How to design your pond and the area around it in an original and tasteful way
These original, and sometimes even fantastic ponds can be created from discarded tires with only effort and creative thinking.
If you decide to throw away the old ones and don't tell anyone necessary items, think carefully maybe they will be useful for making original decor in the design of a recreation area in the garden or in the yard in the country.
Do-it-yourself reservoirs from tires: we create a pond, pool or fountain in the country
Old tires are not just obsolete rubber.
This is a valuable high-quality secondary raw material. Reliable, strong and durable.
You can get tires free or very cheap.
Tires can be used to create many useful things.
Of these, you can create a small reservoir of tires with your own hands for a summer cottage or garden, namely:
Let's figure out what is needed to create such reservoirs.
Building a decorative pond
To create a small decorative pond, it is quite enough passenger car tires.
Tools
In our work we will use:
- two shovels (bayonet and shovel), as well as crushed stone and sand;
- building level and electric jigsaw;
- waterproofing material to cover the bottom; the best option- special cover for swimming pools;
- small boulders to beautifully decorate the banks of the pond;
- plants for ornamental ponds.
If you want to create not just a decorative pond, but a real swimming pool, you cannot do without large KAMAZ or BELAZ tires.
Operating procedure
First, remove the top of the tires. Best Tool for cutting - electric jigsaw . It should work at low speeds.
An alternative but less effective tool is hacksaw for metal. It will take an order of magnitude longer to remove the tire top.
Now create a recess for the pond:
- first of all, we level the territory for the future reservoir;
- then we dig a recess for the tires to create the base of the pond; around the entire circumference we leave a small space for the allowance - the tires should not sit tightly in the recess;
- put tires; using the level, we check how horizontally exactly relative to one another they are all stacked.
Pond it is better not to build in the sun, otherwise the plants in it will wither, and duckweed will cover the water.
In the shadow large trees building a pond is also not worth it - clog up quickly twigs and leaves.
The ideal place for him is partial shade.
To prevent the pond from leaking, you will need special materials that cover the bottom of the pools. As a cheap and not very reliable alternative suitable pvc film.
The shelter should completely cover the tires and extend approximately 0.5 meters beyond their edges.
We carefully spread the bottom cover and fasten it to prevent it from slipping. For this you need to press down the edges with boulders or cover with rubble.
- sprinkle the edges of the shelter with a small amount of sand;
- around the edges of the recesses we put boulders and pebbles - we create “shores”.
Stones are best laid out like this - place large boulders below, smaller ones on top.
The “membrane” itself can also be slightly decorated with small rounded pebbles so that it does not catch the eye.
Gravel and sand are not used for decoration. They make the water very cloudy.
And finally, we plant plants and pour water. The pond is ready.
Fountain
A fountain made of tires in the country is a wonderful element of decor that will add coziness and surprise guests. Making it yourself is not at all difficult.
Tools
To make a fountain, you will need the following tools and materials:
- large tire (from a truck or tractor);
- shovel, cement mixture(in dry ready-made), as well as a container for its breeding;
- a mixture of sand and gravel;
- mastic for waterproofing and a pump for pumping water;
- reinforcement in the form of rods, a thin iron sheet and metal posts;
- scissors for cutting metal.
It's good if you have more on hand. building level- the product will come out more accurate and verified.
Procedure
The fountain is created like this:
- First, we pull out a shallow funnel-shaped pit, whose size should be slightly wider than the diameter of the tire.
- We fill the bottom of the pit with a pillow from the mixture sand and gravel.
- On the pillow we pour cement- the future basis for the foundation. Its height should be approximately 10-12 cm. How horizontally even the base is, we check using the building level.
- When the base is well seized and dries to the bottom of the pit, we begin to “hoist” a tire on it. But first, on one side, we slightly shorten its upper part.
- We will protect our giant tire from leaks with the help of rubber mastics for waterproofing. Pour its thick mass into the middle of the tire. We pour a little mastic - a small layer of it is enough for waterproofing.
- Use thin sheet iron around tire circumference create formwork.
- We stack reinforcing bar and fill with cement mixture.
- The edges and bottom of our fountain decorate all the same small non-sharp boulders and pebbles.
- Well, in the middle of the fountain put the pump with a special nozzle to spray water.
Wheel pool
As in the case of the fountain, the pool needs a large tire of some sort. trucks or large special equipment.
The used tires of the Belaz dump truck, L-170 or T-150 tractors are perfect. A popular option is from the K 700 tire.
materials
To create a pool from a wheel, we take the following materials and tools:
- half a bag of cement and sand;
- some laundry soap;
- a hacksaw, as well as a well-sharpened knife;
- paint and stones for decoration.
Process of creation
First we prepare the tire. one of her cut off the side with a sharp knife. We leave only the side. For the pool, such a shortened tire is quite enough. To make it easier to wield a knife, we lubricate the place on the tire where we are going to cut with laundry soap.
Now we are preparing a place where we will put the tire.
To start we clean the site: remove the roots of trees, level the soil with a rake.
Then dig a hole. There are several options, depending on how the future reservoir appears:
- If you need him to be partially dug in, depth and diameter should be approximately two thirds of the diameter and height of the shortened tire. When dug, we create a 15-centimeter gravel or sand cushion at the bottom of the pit so that it takes on the pressure of the tire and water. The pillow is well aligned.
- If you want the pool was not buried, we make the pit wider than the tire diameter by approximately one spade bayonet. We fill such a recess with sand and carefully tamp.
Be sure to use cement (it will need 2-3 buckets) we strengthen the loose circumference of the recess.
Next, we put a tire in it, and in the hole pour one and a half buckets of cement. The binder material must be carefully leveled to seal the future pool, remove all cracks and protect it from leaks.
The cement will dry and set well in 2-3 days.
drain cock
It is necessary to create a special tap to drain and replace water in the pool. We will need:
- a pipe with a faucet and a corner for a pipe;
- washers (large diameter);
- nut and locknut (second nut screwed onto the bolt).
The drain cock is most conveniently placed on the side at the bottom of the tire:
- we attach a corner to the pipe with a faucet;
- make a small hole at the bottom of the tire;
- we cut the pipe, connect it with a nut, a lock nut and a large diameter washer.
Decor
Now it remains to paint the pool and lay out the stone wall. In the photo, a decorative springboard is also lined with stones. The pool is covered with a protective mesh.
This video describes the creation of a film pond with the participation of old tire from passenger car:
Conclusion
It takes quite a bit of effort and patience to recycle tires wisely and create beautiful and useful water bodies from them. Do-it-yourself ponds and pools for summer cottages will please the eye for many years to come.
If there is a desire and tires remain, you can not be limited to a reservoir on the site: old rubber is useful for creating garden paths, children's swings and even a country fence.
A discovery that has been successfully inhabiting country gardens for many years is a do-it-yourself decorative pond from a tire
The ingenuity and ingenuity of the Russian people have already entered the canvas of historical and everyday anecdotes. Indeed, who else can so unexpectedly find a use for unnecessary items, to make a useful thing out of junk?
With the development of the automotive industry, the problem of used tires has arisen. At the same time, flowerbeds made of tires, fences and even children's attractions appeared in the city courtyards. The technology of constructing a decorative pool for a summer residence from an old tire cover was not kept secret for long - now craftsmen are developing various elements of modernization for this know-how.
From what tire can you make a country pond?
The choice of blank largely depends on the place that you can allocate on your site for this decorative "highlight". Not enough space - a tire from a passenger car, more space - good:
- KAMAZ tires;
- rear wheels of the tractor "Belarus";
- tire from a 45-ton "BELAZ".
What kind of pond can be built?
Of course, in such a pond it will not be possible to breed fish, but land water lilies, marsh turkey and floating pondweed, and along the banks - Siberian iris, it is quite real.
With a decorative flagstone, you can hide the rubber base, break an alpine hill next to it - and no one will guess about the fundamental principle of your decorative pond.
Photo of mini-reservoirs from tires with your own hands, which you can do in the country with your own hands.
What will the craftsman need in the course of work?
Tool:
- shovels (bayonet and shovel);
- building level;
- hacksaw or jigsaw.
Consumables:
- sand;
- crushed stone;
- stones;
- soft sealant;
- plants for decoration.
Video about creating an artificial pond from a car tire with your own hands.
How to move towards the result, having the right tire on hand?
How to make a decorative mini-pond from an old tire with your own hands in a country house or a plot of a house? Step-by-step instruction with photo:
- A tire cleaned of dirt must be prepared in a special way - cut off the top. This can be done with a sharp knife, a jigsaw (at low speeds) or a hacksaw.
Choosing a place under the water on the sunny side of the site, in a recreation area, away from big trees so as not to bury their offspring under their fallen leaves.
- on the surface of the leveled area;
- buried in the ground by a third;
- buried in the ground for the entire width of the treads.
At this stage of work, the "newborn" pond can be revive the fountain, for which a small pump or turbine for an aquarium with a nozzle is suitable. For the operation of such a fountain, an electrical connection is required. For safety, it is fashionable to put the wire in a plastic hose and dig it in.
Another video on how to make a pond with a tire fountain.
An interesting addition would be garden lamp lighting on solar batteries. During the day, it accumulates energy, and in the evening it gives soft light.
- If the bottom of a man-made reservoir is camouflaged with gravel or sand, the water will become cloudy.
- So that small animals living in the garden do not accidentally die in the pond, you can place a picturesque snag in it, along which they can get out of the water.
Options for decorative solutions for a tire pond
- It is possible to build from different-sized or equal-sized tires two ponds contacting protectors. In progress decorative design above the junction, according to Russian tradition, to install a bridge from birch logs unpeeled from the bark - a beam bridge. The bridge can be a plank, and even with a railing. It can be purely decorative or part of a garden path.
- If one tire is installed in a recess, and the other on the surface of the site, you can get two ponds with overflow. An overflow can provide rainwater drainage from the roof or a homemade waterfall.
You can make it by bringing it to the upper pond, through the thickness of decorative heaps of stone, a thin hose with weak pressure water. The flow of water, which will fall from the height of the stones, will provide overflow to the lower pool.
Photo of finished ponds in the country or a plot of the house with your own hands from tires.
Decorative pond from a tractor tire
Not infrequently, with bated breath, we look at photos of decorative reservoirs on the Internet and dream of arranging something similar on our own site. But the process of creating a country pond at first glance is not so simple, it requires certain knowledge in the field of establishing elementary plumbing systems, gardening, as well as some building skills.
It's no secret that having made a couple of mistakes during work, beauty enthusiasts are disappointed in the final product of their work and no longer get down to business, preferring to be content with beautiful pictures in magazines about landscape design. But in vain. After all, the creation of a reservoir is a serious matter and, without experience, it is not always possible to get the desired result the first time.
Therefore, it is necessary to carefully study the Internet on this issue and be prepared for failures - our eternal companions on the path to success. The main thing to remember is that experience is the best teacher and don't be afraid to experiment.
In the meantime, in order to get closer to what you want and equip your dream decorative pond on your site, we advise you to start small. Namely, from the creation of a small decorative reservoir from an old tractor tire. It will take much less time than usual, but we are sure that in the process you will acquire many useful skills for the future.
Today we will not use any expensive materials and will try to save some time and money from the family budget.
So, to create a decorative mini-pond on suburban area you will need:
1. Materials:
- tractor tire (you can take a large tire from any large truck);
- polyethylene film as an insulating material;
- a small pump;
- stones for decoration;
- small gravel for arranging the bottom of the reservoir or sea pebbles;
- ornamental plants to taste (better undersized).
2.Tools:
- electric jigsaw;
- shovel;
- wheelbarrow.
Step 1: choose a location
The choice of place should be taken with all responsibility. If possible, it should be more or less level ground. It is not recommended to locate a reservoir in a site open to sunlight throughout the day, since the water will be very hot, and this is fraught with the development of pathogenic microorganisms and algae in it.
Also pay attention to the presence of deciduous trees above the surface of the reservoir. All the leaves from them will end up in your pond in the fall, and you will have to clean it almost every day during the leaf fall.
In addition to the above conditions for choosing a place for a reservoir, it is also worth highlighting the absence of a strong wind.
Step 2: preparing the pit
Dig and level the hole for the tractor tire so deep that half of the tire is above the ground. If you do not want to spoil the lawn, then before laying the ground, you will have to cover it with a film or any other durable covering material.
Although our pond will not be that big, the amount of land that you have to take out is measured in several wheelbarrows, and even several dozen wheelbarrows. To avoid such hard work, we advise you to think about arranging an alpine slide near a pond with ornamental plants. It can be made from excavated soil and the remains of stones, which, for one reason or another, were not in demand when decorating the reservoir itself. We, for example, did just that and were extremely pleased with the result of our labors.
Step 3: Tire Preparation and Insulation
You need to cut off the top of the tire as shown in the photo. The easiest way to do this is with a jigsaw. Since the material is very thick and durable, it will be very difficult to cut it manually with a knife, for example.
For decoration we used natural stone. Here you will have to play a game of Tetris, selecting and stacking stones properly. As a result, it is necessary to achieve a complete and harmonious composition, smoothly turning into an alpine hill.
Step 5: Alpine slide
Creating an alpine slide is an exceptionally creative and intuitive activity, and besides, it is a matter of taste, so any recommendations are superfluous here.
In any case, you have everything you need: fertile soil from the pit, the remains of stones and your favorite plants. Therefore, it's time to show a little imagination and complement your decorative pond with an alpine slide to match.
The only nuance that, perhaps, is worth mentioning is the use of predominantly undersized plants for landscaping. Considering small size reservoir, high vegetation can almost completely hide it under its own weight, which is not always necessary.
Step 6: Installing the Pump
At the bottom of the pond lay a small pump, which is usually used in such cases to simulate a fountain. You can find it in any building hypermarket.
In principle, the pump can be completely abandoned, but then it will not be superfluous to arrange a drain of water from the reservoir. The fact is that with insufficient aeration, the water will quickly become cloudy and begin to emit bad smell. Therefore, from time to time it will have to be lowered and filled with a new one - fresh. It is for this reason that the solution using a pump remains the most rational of the others.
IN last resort, the pump can be replaced by a compressor designed to aerate water in aquariums. Its task is to pump air, thereby saturating the water with oxygen. This perfect solution for those who want to protect their ornamental pond from colonization by algae and the development of pathogenic microflora.
The effect of the compressor, of course, is not the same as when using the pump. But the dynamics from the formed air bubbles on the water surface is guaranteed to you.
We used a pump that we found in the landscaping department.
For the winter period of cold weather, water from the reservoir must be drained. In other circumstances, it would be nice to store the film laid as an insulating material, but since it is securely fixed with stones, this is, of course, not so easy to do.
In the meantime, just enjoy the beautiful creation own hands!
Source
Receive a selection of new homemade products by mail. No spam, just useful ideas!
*By filling out the form you agree to the processing of personal data
Do-it-yourself tire pond
Often, the owners of cottages or plots want to decorate their possessions by making ponds with their own hands from a tire. Such a reservoir made of tires undoubtedly becomes a good source of coolness and pleases the owner himself, as well as his guests, and is an adornment of the entire summer cottage. Only the sight of a pond and its water surface is enough for a person to relax and feel like a real vacation. However, some, judging that their own site is not so big, do not move beyond just a dream. And in vain! This article will show you step by step how to make a pond in the country with your own hands from tires or tires.
- Where to find the right tire
- Now for the step by step tutorial.
- For swimming and bathing
- For decorative purposes
- Conclusion
- Tire jacuzzi (video)
Show all content
Place for your mini-pond: how to find it
It should be located where it will attract our attention, so you need to choose it very carefully. It is important to follow a few rules that will help make your choice successful:
- Your pond does not need to be constantly in the sun. The best place for the location of the reservoir - partial shade. If this factor is neglected, then the plants will wither, and the water will bloom.
- The space open to the winds is also not suitable.
- A pond surrounded by trees will quickly fill with fallen leaves and wood dust. Such a pond will need to be cleaned frequently, which will require a lot of time and effort.
It would be great if the reservoir is located in a place overlooked from everywhere. Then the whole surrounding landscape will be well reflected in it. When such small reservoirs are in a lowland, they look much more attractive. Therefore, when looking for a place for a pond, then try to find such a natural recess in the area. Eat good way find such a site without spending much effort.
The picture shows a place where your pond will not be under the constant rays of the sun, and also which is visible well from different sides.
Previously, you can simulate the location of the future pond by placing a piece polyethylene film in the place of your choice. Now go around it to see how the future mini-reservoir will supposedly look from different sides. If you like it, then this is the right place.
Where to find the right tire
Before looking for the right tire, you need to consider what size pond you need and how deep. If there is not enough space for a large structure in the summer cottage, then just one slope from the car will be enough for this. And if a piece of land large sizes, then for this project you need larger tires, with a diameter even higher than a person's height. For example:
- Slopes from a KamAZ car;
- Tractor wheel "Belarus";
- Tires from BelAZ.
What to do when there is no suitable tire? The right one can be found at a service station, where there is a lot of rubber, which will still have to be disposed of. You can look for used tires at any car depot or ask a neighbor who has a car. Sometimes used tires just lie on the side of the road.
Large slopes from Gulliver, Kamaz, BelAZ are not easy to find. Often they are not suitable for our relatively small areas.
What will your pond look like?
Would you like to have fish in your lake? In a small lake, this is hardly possible. But if you have a pond from a large tire, then you can start, for example, goldfish. But in another case, if the structure was not made for fish, then it can be decorated with various plants, pebbles, animal imitations and other artificial decorations. In general, it all depends on your taste and imagination.
So that no one guesses how your mini-pond appeared, you need to close the rubber base well with a stone. You can also add lighting from lamps to the decoration. During the day they collect the energy of the sun, and at night they reflect beautifully from the pond.
Mini pool for children (video)
However, one should not forget that any mini-pond may turn out to be unsafe for small children who are left by themselves near the pond without adults.
The decoration of the pond has two sides. When decorating a pond, we think about the aesthetic appearance. But you need to remember that kids can also become connoisseurs of beauty, who are also attracted by decor and various figures. Children should not be left near water without adult supervision.
Now for the step by step tutorial.
The success of any undertaking depends on good preparation. Must be pre-assembled the right materials and tools - this will help you once again not be distracted during the main work.
Step one - collect inventory, procure materials
Inventory: shovel and large sapper shovels, building level, electric jigsaw or hacksaw.
Materials: car tires, polyethylene or special waterproofing material for pools, sand, gravel, large stones for decorating the edges of the pool, plants for landscaping.
When everything you need is collected, proceed to the second step.
Step two - preparing the tire
We first remove dirt from the tire. After that, you need to cut off the top of the slope.
On the tire, you need to cut off the upper part
Step three - dig a hole for the pond
To start digging a hole, you need to level the surface that we have outlined for the reservoir. Also, before starting work, you need to set the depth of the future lake, according to the rubber base, as well as the desired look.
Dig a hole
The rubber base of the reservoir can be:
- Lower to the depth of the entire tread.
- Dig in half
- Leave most on the surface of your site.
We dig a hole. We make a shape that corresponds to the outer diameter of the tire, with small indents around the entire circumference for free lowering it to the required depth.
If you do not bury the tire completely in the ground, then the remaining side will protect your pond from sewage.
The pit needs to be dug, taking into account the necessary "cushion" of sand (about 15 cm). We pre-align the bottom so that the waterproofing gasket is not damaged. If necessary, the sand must be sifted to remove hard lumps and small pebbles in advance. The bottom is important to carefully tamp and align horizontally.
Construction stages
Step four - waterproofing device
You can use ordinary polyethylene, but keep in mind that it is short-lived. After a short use, it deteriorates from exposure to the sun, water and temperature changes. It is better to take waterproofing for the construction of stationary pools, which is much more practical. It is sold in specialized stores or in construction stores. Of course, when using special waterproofing, the cost of your pond will be higher, but the water from it will not flow into the soil. I do not want it to be like in the saying: "the miser pays twice."
Instead of a film, it is better to take waterproofing material
How much material is needed? As much as needed so that the canvas covers the bottom of the tire, fits against the walls, and so that there is another half a meter of film beyond the edges of the pool. In order for the waterproofing material to fit snugly to the bottom and walls, it is best to fill the entire container with water when laying. She will push everything internal surfaces reservoirs and give them correct form. Try to straighten the waterproofing material well. To keep it in the right position, press down on the edges with large rolled stones.
Decorating a pond with stones
Step five - install the walls and bring beauty to the pond
The edges waterproofing material level and sprinkle with sand and screenings. Now the membrane is fixed completely and will not move out. Sand will be the main material for the design of the future reservoir.
Designer's tips for installing a tire pond (video)
How you want to use your reservoir will depend on the versions of the distribution of stones.
For swimming and bathing
In order for your project to build for swimming, the tire must be quite large. Do not overload the banks of this structure with large stones, otherwise bathers may suffer. Great option it would be easy to form a platform along the walls.
For decorative purposes
In another case, if the pond is only for design purposes, then you will have to fantasize about the distribution of stones and plants and decor, thereby emphasizing the look of your yard and making others happy with it. Now don't worry about the jagged rocks, it will look very impressive.
decorative pond with a fountain
It is advisable to lay the stones in rows: large and rounded stones - from below, and small stones - from above. Miniature, seawater-smoothed pebbles will help beautifully cover the bottom of a mini-pond. Sand with gravel is not recommended as a bottom decoration due to the fact that the water becomes cloudy and unpleasant in appearance.
Small or medium-sized animals live in every yard. For example: hedgehogs, moles or mice. If you do not want to see them dead in your reservoir, then take the time and effort to find a snag that will give originality to your reservoir, well, and if you're lucky, it will save the life of some small animal.
Conclusion
Decorating your yard or garden with such an original structure is very simple and does not require large cash outlays. All you need is a little time and energy and imagination. The work itself will bring you satisfaction, and the result will bring joy to you and your loved ones.
Old tires are not just obsolete rubber.
This is a valuable high-quality secondary raw material. Reliable, strong and durable.
You can get tires free or very cheap.
Tires can be used to create many useful things.
Of these, you can create a small reservoir of tires with your own hands for a summer cottage or garden, namely:
- decorative pond;
- pool;
- fountain.
Let's figure out what is needed to create such reservoirs.
To create a small decorative pond, it is quite enough passenger car tires.
Tools
In our work we will use:
- two shovels (bayonet and shovel), as well as crushed stone and sand;
- building level and jigsaw;
- waterproofing material to cover the bottom; the best option is a special cover for pools;
- small boulders to beautifully decorate the banks of the pond;
- plants for ornamental ponds.
If you want to create not just a decorative pond, but a real swimming pool, you cannot do without large KAMAZ or BELAZ tires.
Operating procedure
First, remove the top of the tires. Best cutting tool electric jigsaw. It should work at low speeds.
An alternative but less effective tool is hacksaw for metal. It will take an order of magnitude longer to remove the tire top.
Now create a recess for the pond:
- first of all, we level the territory for the future reservoir;
- then we dig a recess for the tires to create the base of the pond; around the entire circumference we leave a small space for the allowance - the tires should not sit tightly in the recess;
- put tires; using the level, we check how horizontally exactly relative to one another they are all stacked.
Pond it is better not to build in the sun, otherwise the plants in it will wither, and duckweed will cover the water.
In the shade of large trees building a pond is also not worth it - clog up quickly twigs and leaves.
The ideal place for him is partial shade.
To prevent the pond from leaking, you will need special materials that cover the bottom of the pools. As a cheap and not very reliable alternative suitable pvc film.
The shelter should completely cover the tires and extend approximately 0.5 meters beyond their edges.
We carefully spread the bottom cover and fasten it to prevent it from slipping. For this you need to press down the edges with boulders or cover with rubble.
- sprinkle the edges of the shelter with a small amount of sand;
- around the edges of the recesses we put boulders and pebbles - we create “shores”.
Stones are best laid out like this - place large boulders below, smaller ones on top.
The “membrane” itself can also be slightly decorated with small rounded pebbles so that it does not catch the eye.
Gravel and sand are not used for decoration. They make the water very cloudy.
And finally, we plant plants and pour water. The pond is ready.
Fountain
A fountain made of tires in the country is a wonderful element of decor that will add coziness and surprise guests. Making it yourself is not at all difficult.
Tools
To make a fountain, you will need the following tools and materials:
- large tire (from a truck or tractor);
- a shovel, a cement mixture (in a dry finished form), as well as a container for diluting it;
- a mixture of sand and gravel;
- mastic for waterproofing and a pump for pumping water;
- reinforcement in the form of rods, a thin iron sheet and metal posts;
- scissors for cutting metal.
It's good if you have more on hand. building level- the product will come out more accurate and verified.
Procedure
The fountain is created like this:
- First, we pull out a shallow funnel-shaped pit, whose size should be slightly wider than the diameter of the tire.
- We fill the bottom of the pit with a pillow from the mixture sand and gravel.
- On the pillow we pour cement- the future basis for the foundation. Its height should be approximately 10-12 cm. How horizontally even the base is, we check using the building level.
- When the base is well seized and dries to the bottom of the pit, we begin to “hoist” a tire on it. But first, on one side, we slightly shorten its upper part.
- We will protect our giant tire from leaks with the help of rubber mastics for waterproofing. Pour its thick mass into the middle of the tire. pour a little - a small layer of it is enough for waterproofing.
- Use thin sheet iron around tire circumference create formwork.
- We stack reinforcing bar and fill with cement mixture.
- The edges and bottom of our fountain decorate all the same small non-sharp boulders and pebbles.
- Well, in the middle of the fountain put the pump with a special nozzle to spray water.
Wheel pool
As in the case of the fountain, the pool needs a large tire of some sort. trucks or large special equipment.
The used tires of the Belaz dump truck, L-170 or T-150 tractors are perfect. A popular option is from the K 700 tire.
materials
To create a pool from a wheel, we take the following materials and tools:
- half a bag of cement and sand;
- some laundry soap;
- a hacksaw, as well as a well-sharpened knife;
- paint and stones for decoration.
Process of creation
First we prepare the tire. one of her cut off the side with a sharp knife. We leave only the side. For the pool, such a shortened tire is quite enough. To make it easier to wield a knife, we lubricate the place on the tire where we are going to cut with laundry soap.
Now we are preparing a place where we will put the tire.
To start we clean the site: remove the roots of trees, level the soil with a rake.
Then dig a hole. There are several options, depending on how the future reservoir appears:
- If you need him to be partially dug in, depth and diameter should be approximately two thirds of the diameter and height of the shortened tire. When dug, we create a 15-centimeter gravel or sand cushion at the bottom of the pit so that it takes on the pressure of the tire and water. The pillow is well aligned.
- If you want the pool was not buried, we make the pit wider than the tire diameter by approximately one spade bayonet. We fill such a recess with sand and carefully tamp.
Be sure to use cement (it will need 2-3 buckets) we strengthen the loose circumference of the recess.
Next, we put a tire in it, and in the hole pour one and a half buckets of cement. The binder material must be carefully leveled to seal the future pool, remove all cracks and protect it from leaks.
The cement will dry and set well in 2-3 days.
drain cock
It is necessary to create a special tap to drain and replace water in the pool. We will need:
- a pipe with a faucet and a corner for a pipe;
- washers (large diameter);
- nut and locknut (second nut screwed onto the bolt).
The drain cock is most conveniently placed on the side at the bottom of the tire:
- we attach a corner to the pipe with a faucet;
- make a small hole at the bottom of the tire;
- we cut the pipe, connect it with a nut, a lock nut and a large diameter washer.
Decor
Now it remains to paint the pool and lay out the stone wall. In the photo, a decorative springboard is also lined with stones. The pool is covered with a protective mesh.
This video is about creating a film pond using an old car tire:
Conclusion
It takes quite a bit of effort and patience to recycle tires wisely and create beautiful and useful water bodies from them. Do-it-yourself ponds and pools for summer cottages will please the eye for many years to come.
If there is a desire and tires remain, you can not be limited to a reservoir on the site: old rubber is useful for creating, and even.
In contact with
Often, the owners of cottages or plots want to decorate their possessions by making ponds with their own hands from a tire. Such a reservoir made of tires undoubtedly becomes a good source of coolness and pleases the owner himself, as well as his guests, and is an adornment of the entire summer cottage. Only the sight of a pond and its water surface is enough for a person to relax and feel like a real vacation. However, some, judging that their own site is not so big, do not move beyond just a dream. And in vain! This article will show you step by step how to make a pond in the country with your own hands from tires or tires.
Place for your mini-pond: how to find it
It should be located where it will attract our attention, so you need to choose it very carefully. It is important to follow a few rules that will help make your choice successful:
- Your pond does not need to be constantly in the sun. The best place for the location of the reservoir is partial shade. If this factor is neglected, then the plants will wither, and the water will bloom.
- The space open to the winds is also not suitable.
- A pond surrounded by trees will quickly fill with fallen leaves and wood dust. Such a pond will need to be cleaned frequently, which will require a lot of time and effort.
It would be great if the reservoir is located in a place overlooked from everywhere. Then the whole surrounding landscape will be well reflected in it. When such small reservoirs are in a lowland, they look much more attractive. Therefore, when looking for a place for a pond, then try to find such a natural recess in the area. There is a good way to find such a site without spending a lot of effort.
The picture shows a place where your pond will not be under the constant rays of the sun, and also which is visible well from different sides. Previously, you can simulate the location of the future pond by placing a piece of plastic wrap in the place you have chosen. Now go around it to see how the future mini-reservoir will supposedly look from different sides. If you like it, then this is the right place.
Where to find the right tire
Before looking for the right tire, you need to consider what size pond you need and how deep. If there is not enough space for a large structure in the summer cottage, then just one slope from the car will be enough for this. And if the plot of land is large, then for the implementation of this project you need larger tires, with a diameter even higher than a person's height. For example:
- Slopes from a KamAZ car;
- Tractor wheel "Belarus";
- Tires from BelAZ.
What to do when there is no suitable tire? The right one can be found at a service station, where there is a lot of rubber, which will still have to be disposed of. You can look for used tires at any car depot or ask a neighbor who has a car. Sometimes used tires just lie on the side of the road.
Large slopes from Gulliver, Kamaz, BelAZ are not easy to find. Often they are not suitable for our relatively small areas. What will your pond look like?
Would you like to have fish in your lake? In a small lake, this is hardly possible. But if you have a pond from a large tire, then you can start, for example, goldfish. But in another case, if the structure was not made for fish, then it can be decorated with various plants, pebbles, animal imitations and other artificial decorations. In general, it all depends on your taste and imagination.
So that no one guesses how your mini-pond appeared, you need to close the rubber base well with a stone. You can also add lighting from lamps to the decoration. During the day they collect the energy of the sun, and at night they reflect beautifully from the pond.
Mini pool for children (video)
However, one should not forget that any mini-pond may be unsafe for small children who are left alone near the pond without adults.
The decoration of the pond has two sides. When decorating a pond, we think about the aesthetic appearance. But you need to remember that kids can also become connoisseurs of beauty, who are also attracted by decor and various figures. Children should not be left near water without adult supervision. Now for the step by step tutorial.
The success of any undertaking depends on good preparation. You need to collect the necessary materials and tools in advance - this will help you once again not be distracted during the main work.
Step one - collect inventory, procure materials
Inventory: shovel and large sapper shovels, building level, electric jigsaw or hacksaw.
Materials: car tires, polyethylene or special waterproofing material for pools, sand, gravel, large stones for decorating the edges of the pool, plants for landscaping.
When everything you need is collected, proceed to the second step.
Step two - preparing the tire
We first remove dirt from the tire. After that, you need to cut off the top of the slope.
On the tire, you need to cut off the upper part Step three - dig a hole for the pond
To start digging a hole, you need to level the surface that we have outlined for the reservoir. Also, before starting work, you need to set the depth of the future lake, according to the rubber base, as well as the desired look.
Dig a hole The rubber base of the reservoir can be:
- Lower to the depth of the entire tread.
- Dig in half
- Leave most of it on the surface of your site.
We dig a hole. We make a shape that corresponds to the outer diameter of the tire, with small indents around the entire circumference for free lowering it to the required depth.
If you do not bury the tire completely in the ground, then the remaining side will protect your pond from sewage.
The pit needs to be dug, taking into account the necessary "cushion" of sand (about 15 cm). We pre-align the bottom so that the waterproofing gasket is not damaged. If necessary, the sand must be sifted to remove hard lumps and small pebbles in advance. The bottom is important to carefully tamp and align horizontally.
Construction stages Step four - waterproofing device
You can use ordinary polyethylene, but keep in mind that it is short-lived. After a short use, it deteriorates from exposure to the sun, water and temperature changes. It is better to take waterproofing for the construction of stationary pools, which is much more practical. It is sold in specialized stores or in hardware stores. Of course, when using special waterproofing, the cost of your pond will be higher, but the water from it will not flow into the soil. I do not want it to be like in the saying: "the miser pays twice."
Instead of a film, it is better to take waterproofing material How much material is needed? As much as needed so that the canvas covers the bottom of the tire, fits against the walls, and so that there is another half a meter of film beyond the edges of the pool. In order for the waterproofing material to fit snugly to the bottom and walls, it is best to fill the entire container with water when laying. It will press on all the internal surfaces of the reservoir and give them the correct shape. Try to straighten the waterproofing material well. To keep it in the right position, press down on the edges with large rolled stones.
Decorating a pond with stones Step five - install the walls and bring beauty to the pond
We level the edges of the waterproofing material and sprinkle with sand and screenings. Now the membrane is fixed completely and will not move out. Sand will be the main material for the design of the future reservoir.
Designer's tips for installing a tire pond (video)
How you want to use your reservoir will depend on the versions of the distribution of stones.
For swimming and bathing
In order for your project to build for swimming, the tire must be quite large. Do not overload the banks of this structure with large stones, otherwise bathers may suffer. A great option would be to simply form a platform along the walls.
For decorative purposes
In another case, if the pond is only for design purposes, then you will have to fantasize about the distribution of stones and plants and decor, thereby emphasizing the look of your yard and making others happy with it. Now don't worry about the jagged rocks, it will look very impressive.
Decorative pond with fountain It is advisable to lay the stones in rows: large and rounded stones - from below, and small stones - from above. Miniature, seawater-smoothed pebbles will help beautifully cover the bottom of a mini-pond. Sand with gravel is not recommended as a bottom decoration due to the fact that the water becomes cloudy and unpleasant in appearance.
Small or medium-sized animals live in every yard. For example: hedgehogs, moles or mice. If you do not want to see them dead in your reservoir, then take the time and effort to find a snag that will give originality to your reservoir, well, and if you're lucky, it will save the life of some small animal.
Conclusion
Decorating your yard or garden with such an original structure is very simple and does not require large cash outlays. All you need is a little time and energy and imagination. The work itself will bring you satisfaction, and the result will bring joy to you and your loved ones.
Tire jacuzzi (video)
( ArticleToC: enabled=yes )
Most owners of suburban areas would like to have their own artificial pond. The highlight of the landscape - a do-it-yourself tire pond would please the hosts and guests.
After all, it is known that the contemplation of the water surface tunes in a lyrical mood, helps to relax and get a surge of inspiration.
But, as a rule, due to lack of space, many refuse to dream of having a pond - a source of positive emotions and coolness. However, it is possible to make it a reality using the usual car tires, which have served faithfully for car drivers.
In order for a decorative pond to attract attention, it is important for it to choose the right place.
To do this, you must follow the basic rules:
- most suitable place for a do-it-yourself tire pond there will be partial shade. If you build it in the sun, the plants will quickly wither, and the reservoir will lose its attractiveness. Yes, the water will begin to bloom. Windy places are not the best option, as is the construction of a reservoir under the crowns of trees. In the latter case, constantly falling leaves will clog it. It will require frequent cleaning;
- the pond should be visible from different vantage points. Then trees, clouds, a house, etc. will be reflected in its water;
- it is desirable to place the pond in a depression, since a small pond looks better when viewed from above.
How to choose a tire
Next, they proceed to the search for a tire, the choice of the size of which depends on the free space available for the construction. If it is catastrophically small, you need to stop the choice on a tire from a car. If there is enough space for the implementation of a large-scale project, the diameter of the tire can be impressive (more than human growth). It can be a tire from KAMAZ or BELAZ, a Belarus tractor, etc.
It is clear that not every garage has a similar one. But finding a tire of this size is easy by contacting a tire shop or looking at car companies.
Rubber base close up decorative tiles so that it was impossible to guess how the reservoir works.
We decorate the reservoir
They will add exotic fish to artificial reservoirs - even aquarium ones, which feel quite comfortable in them, will do.
But, there are other ways to decorate artificial ponds from tires with your own hands: planting Siberian iris along the banks of a reservoir, breeding water lilies, floating pondweed or marsh turkey.
You can use maintenance-free artificial decorations. Artificial ducks and turtles basking on the shore look great on the surface of the pond.
Completely transform the pond arranged nearby alpine slides. An additional effect at night is created by backlights powered by solar panels, surprising with a mysterious soft glow.
Video: How to make a pond with your own hands
Step-by-step instruction
First of all, you should prepare tools and materials.
They will need a few:
- tire of the right size;
- PVC film or other covering material;
- gravel;
- sand;
- plants and decoration material;
- shovels - bayonet and shovel;
- hacksaw or electric jigsaw;
- level.
Then, proceed to the second stage - the preparation of the tire. Although it will have to be buried in the future, it is necessary to clean the tire of dirt and cut off the upper part.
Of course, you can use a sharp knife for this. But such pruning will require a lot of time and effort. It is better to do the work with a hacksaw or use an electric jigsaw, working with it at low speeds.
Having prepared the tire, they begin to dig a pit, having previously leveled the site. The tire can be deepened to any depth. The shape of the hole for the tire should correspond (with an allowance) to the diameter of the tire.
Having carefully leveled the bottom (check the level), it must be covered with sand by 15 centimeters. The sand is carefully compacted, after which the rubber blank is lowered. It remains to check the horizontal level of the installed tire.
It's time to move on to the next stage - waterproofing;
For her, it is more expedient to use a covering material designed specifically for reservoirs. It is sold in specialized outlets or where they sell goods for the garden.
You need to buy it based on the fact that it should protrude half a meter beyond the tire walls. In extreme cases, thick polyethylene is suitable. But it will last much less. Therefore, giving preference to it, it must be taken into account that a replacement will be required, which is impossible without dismantling the structure. Having distributed the selected material along the bottom of the dug hole, it is taken out beyond the edges of the chamber placed in the hole;
having carefully straightened the material, and having crushed the ends with sand, they proceed to decorating. For him, use a decorative stone.
A do-it-yourself tire pond with overflows, made from several tires with varying degrees of depth, looks bewitching. On the basis of such overflows, beautiful waterfalls are created. Why is a hose connected to the top tire, through which water is supplied under low pressure. It, overflowing the upper container, effectively flows into the container below, water, imitating a waterfall.
Video: Exclusive tire ponds
