Tool box: choosing and making your own. How to make a quality do-it-yourself tool box Do-it-yourself tool box drawings

The various designs of tool boxes discussed in the article are united by the ease of doing it yourself. Choose the right project and, guided by our drawings and photographs, make yourself a convenient portable storage for the tools and equipment used in your work.

simple open box

This box is good because the tools in it are located in their places and are in sight. You can’t put many devices in it, but there is a place for the main ones. An open box is useful in household use when you need to repair something outside the workshop: they reported to the box what was missing and went to work.

A wooden tool carrier comes out heavier than factory counterparts, so you should not plan it too bulky. The box will not beat the knees if you make it narrow. The high handle also adds convenience - you don't have to bend down low to pick it up.

Pick the right pieces of plywood and trim pine boards. Mark and cut out the details of the box. Select the grooves in the blanks with a hand router or make two cuts with a circular saw and clean the recess with a narrow chisel.

Details of the box body: 1 - wall (2 pcs.); 2 - sidewall (2 pcs.); 3 - bottom; 4 - groove along the thickness of the partition and a depth of 1/2-1/3 of the thickness of the material

Sand the surfaces and assemble a rectangular box from blanks. Lubricate the ends with carpentry glue and fasten the parts with small carnations.

Saw out a central partition from 5 mm plywood, the width of which should be 1 mm less than the distance between the grooves in the walls of the box. Mark the location of the cutout for the hand, drill the entry hole for the file, and cut the plywood with a jigsaw.

Partition drawing

Spread the grooves with glue and install the partition in place.

Make two pads for the handle from a block with a section of 20x45 mm, rounding the corners of the blanks with a planer. Prepare rail holders for hand tool: in one, cut out recesses for pliers and pliers with a jigsaw, and drill holes for screwdrivers in the other with a drill. Using glue and screws, fix the parts to the partition by placing them at different heights.

So that the surfaces do not get dirty for a long time, cover the box with varnish.

Toolbox in stool

In this upside down stool, you can move the tool to any place in the house or yard, and put it on its legs, reach for a shelf or hammer a nail where you almost lack your height.

Using plywood or OSB with a thickness of 10-15 mm, cut out the cover (item 1), longitudinal sides (item 2) and sidewalls (item 3) according to the dimensions indicated on the drawings.

Make a handle and four legs with bevels at the ends at an angle of 15 ° from bars with a section of 40x50 mm.

Assemble the stool by fastening the parts with screws.

Box assembly scheme: 1 - cover; 2 - tsarga; 3 - handle; 4 - leg; 5 - sidewall

Round the edges of the cover and the oblong cut in it, apply a finishing coat.

Box for the young master

If your child enjoys crafting or repairing, make a small box with him for his favorite tools.

Take planed 16mm boards and cut out the pieces according to the drawings. Prepare a round birch stick for the handle.

Drawings of the details of the box: 1 - sidewall; 2 - bottom; 3 - handle; 4 - handle stand; 5 - holder

Draw lines parallel to the edges on the sides corresponding to the positions of the handle posts, drill between them through holes under screws.

Remove the burrs with sandpaper and proceed to assemble the box. Connect the bottom and sides with glue and screws, then install the handle stand along the marking lines.

Now replace the second post while inserting the handle into the blind holes. Screw on the screwdriver holders.

Color the box in the color your child chooses.

Wooden box with lid

The necessary set of tools differs depending on the hobby or profession, respectively, and internal organization box may be different. The next tool carrying option is suitable for any equipment, it is distinguished by its solidity and reliability.

Use light wood for the box: pine, linden or poplar. Optimal Thickness planed boards - 12 mm, thinner ones are more difficult to fasten, and thick ones will increase the weight of the structure.

Required accessories:

Pen.
Corners - 8 pcs.
Latch — 2 pcs.
Loop - 2 pcs.

Mark the lumber according to the drawings and cut the blanks.

Cutting blanks for the box

Table. Parts list

Make sure the cutting is correct by folding the box out of the blanks. Sand down all the details one by one. sandpaper No. 220 and label them. Assemble the bottom and lid of the drawer using clamps, corner clamps, or mounting brackets to secure the blanks. Lubricate both joining surfaces with wood glue.

Drill pilot holes for the screws and countersink for the caps, and after fastening the parts, wipe off excess glue with a rag.

Fasten the blanks of the body of the portable part. Replace the dividing partitions by screwing them on the sides and bottom with screws.

Screw the carrying handle in the middle.

Install support rails inside the drawer at a distance of 30 mm from the top.

Clean out pencil marks and burrs near the screws with a fine sandpaper, blow dust off the surface.

Cover the box with a layer polyurethane varnish, after drying, remove the raised pile with a “zero” and repeat the finish.

Align the hinges with the gap between the body and the lid of the box. Mark and make pilot holes for screws 10 mm deep, fasten the hinges.

Screw on the corner pieces using small screws.

Install the handle and latches on the lid.

Fill the finished box with the tool.

If desired, place containers with dividers or cassettes for storing small items in the large compartment of the drawer.

If you decide to add partitions inside the box, make them removable so that you can change the free space for a new tool.

There are many professions in which different kinds tools. Most often, tool boxes are purchased for their storage, but sometimes high-quality storage is easier to do with your own hands.

If you are interested in this or that type of craft, and you are not sitting at home idly by, naturally, you have a fairly large number of tools. To ensure that your tools are always at hand and securely stored, they need to be provided with a storage system in the form of a separate enclosed space called a drawer. for storing tools. In addition to safety, the use of such a box will greatly help in the work, since the filling will be neatly sorted into compartments and in the future you can find necessary fixture"blindly". This device is also necessary for car owners, or rather owners trucks and gazelles. The box must be well secured in the car. And this means that when making it with your own hands, you need to think carefully about where it will be located in the car and how to fix it there.

Decide on two criteria:

Will you only store tools in it, or do you also need it for ease of transportation?
what sizes of tools do you intend to store in it?

Crate classification

Body material:

plastic - light in weight, convenient in everyday life and for transportation;
metal - much heavier than plastic, but at the same time much stronger, more stable, have a more rigid structure, cannot be large sizes due to the severity of the metal;
metal-plastic galvanized - light, durable and roomy, suitable for both storage and transportation of professional tools. But all these advantages determine the corresponding price - it can range from $150 to $500 and more.
wooden - the most available material to make a toolbox. Moreover, it is easier to do it with your own hands from this material, or rather from plywood 10 16 or 18 mm.

By type of stored instruments:

hand tools - as a rule, they are represented by one large compartment for large tools (screwdrivers, hammers, keys) and 2-3 small ones for smaller tools;

an electric tool is a case that is functionally designed to store and move a specific power tool. Most often it has one main compartment for the device itself and several recesses for equipment.
organizers - boxes designed to accommodate a large number tools of various sizes. They have many compartments, models with modular partitions deserve attention, which, for the convenience of the owner, can be rearranged from one place to another.
professional tool - a special kind of cases with certain seats for specific tools that are more resistant to drops and adverse environmental conditions.
non-professional tool - consists of boxes of both small and large enough sizes with many compartments and niches for various kinds of tools, often these are cases in the form of bags.

There are many tool box companies such as stanley, fit– american firms, keter- no less popular Israeli company, Spanish company tayg, german Kroft and many others, differing in quality and price of products.

As an alternative to all these firms - the opportunity to make a tool box with your own hands. You can thus save on cost and get a completely competitive option that meets exactly your requirements.

Types of boxes

Tool boxes made in home workshops are mostly made of wood and come in a variety of shapes. Popular and easy to make boxes classical form- "basket". in the second and third place - a box in the form of a chest - a container, and in the form of a case.

Materials for making a tool box

wooden boards 15-25 mm thick
round wooden rod of the desired length
self-tapping screws, wood glue, sandpaper for cleaning surfaces
set of tools - Sander, electric drill, jigsaw, screwdriver
measuring instruments - ruler
screwdriver, hammer

Manufacturing steps

Using this technology, it is possible to manufacture boxes of more complex designs, creating required amount compartments and niches.

Using the same technology, it is possible to manufacture a closed box, which is more reliable and convenient for transporting tools.

Additional steps in the manufacture of a box with a lid

For self-manufacturing popular now transformer boxes you will have to break your head more, but it is quite possible to implement this idea.

To do this, using computer programs you need to develop the design you want, but a set will help you to translate it into reality necessary elements, which can be purchased at specialty stores. The number and complexity of the selected elements depends on your requirements for the box. Assembly can be done on wooden base using aluminum strips and corners. Fasteners are made with rivets.

If you are a purposeful and creative person, then the process making a tool box will not be difficult, but by seeing the fruits of this work, you will increase your self-esteem and save budget funds.

This article is about how to wooden box for tools. If you have a lot of tools and want to keep them organized, the best thing you can do is to create a simple wooden box. From our experience, we find them very useful as they are lightweight, durable and provide plenty of storage space for tools. Don't forget that you can adjust the size and design to suit your needs.

The main components of the tool box are made from 20mm boards, as they have a beautiful appearance, and very durable. In addition, we recommend that you glue the joints and fasten everything with self-cuts. Try to screw in the screws as symmetrically as possible.

Upon completion of the assembly, it will be necessary to sand the entire surface of the box. Make sure all edges are smooth, otherwise you could hurt your hands on sharp edges. Also, be sure to check that the heads of all screws are flush with wooden surface. Get rid of dust and chips before painting.

In order to make a wooden tool box, you will need the following:

In order to get precise cuts, we recommend using an electric jigsaw or a good circular saw. Make sure the saw has smooth teeth or it may tear off the edges.

Smart Tip: Also, check that the blade will pass exactly along the cut line before sawing.

In the picture, all the components needed for the box. circular machine can make the job easier as many of the cuts need to be made at an angle.

You must use this blueprint when making components for the crate. Make sure you double check all measurements otherwise the components may not match.

After creation wooden parts you need to drill holes around the edges. As you can see in the picture, you need to plank wooden block to prevent damage to the surface. Drill three holes on the bottom and two holes on the sides.

Smart Tip: If you are not experienced in woodworking, you should draw guidelines for pilot lines. Indent from the edges to prevent splitting of the wood.

If the bottom edges are not smooth, you should carefully sand them with 120 grit sandpaper before assembling.

Coat the bottom ends with wood glue to strengthen the connection. Remove excess glue with a dry cloth, otherwise you will waste time cleaning it.

Press the components firmly and leave for half an hour. If you are using good glue, it will well fasten the joints.

However, screw the screws into the drilled holes anyway.

In order to receive solid construction We recommend using self cutters. Work carefully to prevent damage to wooden components.

Smart Tip: Align all parts before twisting. As you can see in the picture, the edges should be even.

After installing all the components together, the tool box should look like the one in the image.

Make a handle out of a cylindrical wooden rod. Handle diameter is approximately 20-25 mm.

Smart Tip: Use a ruler to cut the rod to the desired length.

Add some wood glue to both ends of the rod before pushing it back into place. Then, drill a hole and screw the cut itself. Hold the handle while twisting, otherwise it may move out of place.

Smart Tip: Leave about 15 mm from the top edge to the wooden handle.

Don't forget to smooth the edges of the wooden components with sandpaper.

Thanks for reading our article on how to make a wooden tool box. What kind of toolbox do you have. Tell in the comments below.

Home instruments have an amazing ability to get lost at the most inopportune moment. If hammers and screwdrivers are used periodically, they are stored anywhere: mezzanines, cabinet shelves, balcony.

Therefore, when the wife asks to hang a shelf, remembering exactly where the drill and self-tapping screws are located will be problematic. It is much more practical and efficient to store tools in a special box, which can be purchased ready-made or made by hand.

What to choose

We note right away that the tool box can be different, and the shape and dimensions directly depend on what is supposed to be stored inside the case.

For hand tools. Usually this is a rectangular design with a handle, where the interior space is delimited into one large compartment and 2-3 smaller compartments. It is convenient to store hammers, screwdrivers, fasteners here.

For power tools. Such cases are usually produced by the manufacturer of the instrument itself. Standard option: portable box, where one cell is reserved for a power tool and exactly repeats its shape, the rest are intended for equipment: drills, batteries and other things.

Organizers. This modular designs consisting of several drawers various forms and sizes. Such options are suitable for professionals and home craftsmen, they are easy to store and transport, help to quickly find any little thing.

When the problem of tool storage arises, the first thing that comes to mind is to purchase a ready-made box in the store. However, this is not the most the best option. The fact is that factory designs are focused on the average buyer, so they may not be suitable for specific model grinders or drills. In addition, the number of tools is usually added and the interior space becomes small.

To avoid these problems, you can make a tool box yourself with a little effort and creativity.

From the boards

If there are few tools, they are used periodically and only for home use, it makes no sense to engage in the manufacture of a complex structure. It is enough to make an ordinary wooden box from boards so that screwdrivers, hammers and self-tapping screws are simply in one place, and not lying around the whole apartment.

Given that we are talking about an elementary product, you can do without a preliminary drawing. The main thing is to decide on the size of the sides. For the material of manufacture, it is better to choose edged board conifers: this is the most affordable option which is easy to process.

Consists of homemade box 5 parts:

2 side walls;
2 end walls;

The elements are cut out in accordance with the planned dimensions, treated with sandpaper and fastened together with self-tapping screws. For greater reliability, the side parts can be fixed with metal corners.

Such a homemade wooden box is inconvenient to carry, but it will help to store tools in one place and not look for them all over the apartment. It can be put in the trunk of a car, on a storage shelf or in a garage. Sizes vary depending on what exactly is supposed to be stored inside.

From plywood

Handmade plywood tool boxes attract attention interesting design. They are easy to use and emphasize the professionalism and qualifications of the home master.

A convenient plywood box with a handle will consist of the following items:

bottom - dimensions 450 * 200 mm, a shallow groove is cut in the middle for a transverse partition;
walls - cut out in the amount of 4 pieces. A groove is also cut in the middle of the end elements;
transverse rack - recommended height 400 mm, length adjusted to the width of the bottom, taking into account the sidewalls. The upper corners of the rack are cut to form a trapezoidal shape.

The assembly is carried out according to this scheme. To begin with, the body elements are glued together, tightly pressed against each other. While the glue dries, a hole is cut in the transverse rack, which will act as a handle, wooden dies can be glued in the upper part for ease of grip. Next, the rack is installed in pre-prepared grooves, fixed with glue.

After completion of the work, a plywood box for tools is obtained, convenient for carrying. However, the design can be made more functional. To do this, wooden dies are glued to the transverse partition with pre- drilled holes where you can put screwdrivers, pliers, side cutters and other necessary to perform homework tools.

To prevent the box from drying out, it is covered with several layers of varnishes. For greater reliability, if desired, the bottom is fastened to the walls with corners.

Transformation into a stool

From plywood and wooden blocks, you can make a portable tool storage box, which, when turned upside down, will turn into a simple stool or stand for working at height. This universal design according to this scheme.

The bars are cut according to the given size. They will serve as legs and be tilted. To make the stool stable, the upper and lower ends are cut off at an angle of 15 degrees.

Sheets of plywood are nailed to the legs, which will become the end walls. The recommended width is 360 mm, the height is selected in such a way as to completely hide the legs without protruding beyond them.

The side walls are cut out of plywood, occupying about half the bar in width. The edges of the rectangle are cut at an angle to exactly match the angle of the legs.

The cover is made rectangular, attached to the ends of the racks with self-tapping screws.

After the work done, turn the resulting stool upside down, turning it into a deep box for storing tools. To make the structure convenient to carry, a wooden block is cut out, which in length will correspond to the distance between the walls. round off sharp corners, screw the bar with self-tapping screws and get a convenient handle, which additionally performs the function of a stiffener.

drawer organizer

It's over complex structure but it's perfect for storage big tool and additional little things: fasteners, corners, carnations and much more. At first glance, such boxes seem to be a complex mechanism, but in fact they can be made on your own, spending a little free time.

The manufacturing process is conditionally divided into 3 stages:

assemble the body. This is a deep plywood box with an open top, which is designed to store a large tool, such as a grinder, a screwdriver or an electric drill. However, you can do the opposite: delimit the interior space into several sections wooden dice and store bolts, nuts and self-tapping screws here;
additional boxes. There will be 4 of them, and they are installed on top of the main box, which must be taken into account when determining the dimensions. Additional drawers should not go beyond the boundaries of the base. To give the structure a complete look, the upper boxes are equipped with lids;
separate elements are combined into a single whole. To do this, the organizer is assembled in finished look, markings are made on the walls for installing metal plates: 3 pieces for a group of boxes on each side. Then, in accordance with the markings, holes are drilled where the bushings are installed.

To make the organizer easy to carry, the top drawers can be additionally equipped with handles.

Note that here are the most simple options. With a little effort, you can turn an ordinary toolbox into a work of art that will become a real decoration of the garage, country house and city apartments.

A box for storing various small things and products is considered an indispensable attribute in a modern economy. Thanks to this design, all things are in their place, while not forming a mess. For example, vegetables and fruits should be stored in a ventilated building where fresh air can freely enter.

For tools, monolithic products without any holes are suitable. For various little things, designs with additional doors and a folding mechanism are suitable.

We offer original variants handmade storage boxes Here you will find out what materials and tools will be needed for the manufacture of these products.

What materials are used to build structures?

Most often, boxes are made of wood and other materials. For tools, it is better to choose solid pine or maple. Alder or aspen is suitable for products. These tree species are distinguished by their durability and strength. They do not emit resinous secretions and do not dry out over time.

Plywood is suitable for the manufacture of decorative products. Here you can place every little thing. To fix the parts, a special adhesive composition is used.

Master class on creating a box with your own hands

We offer step by step instructions how to make a box at home. To do this, you will need the following tools and materials:

tape measure;
simple pencil;
board 25 mm thick;
wooden trimmings 15 mm thick;
thin plywood;
metal corners;
nails and screws;
hacksaw;
screwdriver;
metal hinges for opening the lid structure;
hammer.

The first step is to familiarize yourself with the diagrams and drawings of how to make a box. This will allow you to correctly match the dimensions finished product. Do not make structures too large, as they will take up a lot of free space.

When all the components are ready, you can proceed to the manufacture of a storage system for vegetables and fruits. The process includes several steps:

On the surface of the boards, we mark the size of the side parts of the product. Next, move on to the bottom of the box. We mark the size on the wooden trimmings. After that, using a hacksaw, we begin to cut the blanks.

We fix the boards together with small nails. We fasten the bottom details using the same method.

The cover of the product consists of plywood sheet. It is installed on special hinges, which allow you to control the closing process.

The do-it-yourself box photo shows the entire workflow.

Tool storage box

This type of design is considered best idea do-it-yourself box. This product will allow you to keep all the working tools in one place. Here you can make additional departments for storing screws, nails and nuts.

For this you need to prepare:

thin board;
thick plywood;
hacksaw;
electric jigsaw;
hammer;
screwdriver;
tape measure;
drawing of the finished product;
metal corners.

On sheets of thick plywood, we make markings for the details of the box. After that, we drill holes for fasteners metal hinges. Next, we connect the side parts to each other.

Let's start making the bottom for the storage system. To do this, we attach a thin board to the side of the box. So that it does not fall under the weight of the tools, it must be strengthened with thin boards. To do this, several wooden elements are stuffed on the bottom surface.

In the side parts of the plywood we draw the markings for the handles. They will be cut inside the main body of the product. Here you need an electric jigsaw. The cutting base is installed at the beginning of the markup.

In the process of cutting parts, do not make sudden movements. They can cause cracks on the surface of the product.

Now let's start installing partitions. For this from thin plywood cut out a small square. It is fixed with metal corners in the middle of the structure.