How to hang an extension cord on a closet. How to secure wires: various ways to mount them on the wall. How to attach an extension cord to a wall. Influence of base material

The extension cord with chargers constantly gets in the way on the table or under your feet, collects a lot of dust, and also looks unaesthetic. Dealing with this problem is very simple: take a nice box, make a few holes in it and hide all the wires and cables there.

There are also ready-made solutions, such as Plug Hub from Quirky. This is a box made of hard plastic with a rubberized bottom. There are three holes on top for cables, and inside there are three fasteners that can be used to wrap cords that are too long. The Plug Hub can be placed on the floor or mounted on the wall.

amazon.com

2. Secure the wires under the tabletop

To secure the wires and extension cord under the table, you will need binders and screws (their length should be at least a quarter less than the thickness of the table top, otherwise they will go right through and the table will be damaged). First of all, attach an extension cord under the tabletop, preferably in the middle of the table or closer to the wall. Then secure the binders in the required places using screws. Connect everything you need to the extension cord and collect the wires with clamps. Visually the table has become much cleaner and neater.

There is a simpler option if you don’t need to hide a large number of wires. This will require construction stapler. To prevent the long wire from the lamp from dangling under your feet, carefully secure it with paper clips at the table leg. A small extension can also be secured with paper clips. For thicker wires, it is better to use special clamps (for example, these).

Stapler clips aren't your thing? Regular zip ties will do. Secure the wire to the table leg with zip ties. Wires that run along the floor can be covered with plastic or a board that matches the color of the floor. The extension can be secured under the tabletop using wide Velcro: secure it to the back side countertops, and then attach the extension. To prevent the wires from dangling under the table, run them through cable channels - they can be purchased at any hardware store. You can fix the channels themselves with electrical tape or a regular plaster.

3. Organize your cable storage

They will help you get rid of tangled wires. proper organization. First, collect cords from phones, players, game consoles, and tablets throughout the house. Then take boxes (preferably prettier ones), place cardboard dividers inside them, label the location for each cable (so you don’t get confused later) and lay everything out neatly. To prevent the wires themselves from getting tangled, use regular cable ties.

If you don't want to bother with boxes, buy a basket and accumulate more bushings from toilet paper.

If the wires don't bother you, you can simply attach a label to each one to make it easier to distinguish between them. For example, like this:

4. Keep all necessary wires at hand

We can’t hide all the cables in a box: we need some of them almost constantly. The solution is simple: secure them to the edge of your desktop so that you can reach out and connect the device to your desktop if needed. the right wire. Sugru will help us with this - plasticine-rubber and one of the most irreplaceable things in the household. Don't believe me? Then take a look.

Roll Sugru into small balls and secure them to a table support. Then use a utility knife to remove some of the plasticine (be careful, try not to deform the balls too much). Life hack: to prevent the plasticine from sticking to the blade, first rinse it with soapy water. Then adjust the shape a little with a sushi stick or toothpick to create neat hollows (they should be slightly wider than your wires). Everything is ready, you can fix the cables.

There is an option for those who know how to work with wood. A small block with holes will help organize all the wires on your desktop.

The simplest solution is to pass the wires through binders attached to the tabletop.

hexjam.com

5. Don't hide wires

Seriously, if you get creative, cables can become interesting element decor.

Hello to all DIYers!

In everyday life, we all often have to use various extension cords. Moreover, if for street conditions or summer cottage Basically, extension cords with a long cable are used, several tens of meters long, but for indoors (sheds, garages, workshops or at home), extension cords with a block of three or four sockets and a wire length of 3 to 5 are most often used. 7 meters.

From my own experience, I have found that when using such extension cords, it is best to hang them on the wall. In this case, neither the extension cord itself, nor its wire, as well as the wires of electrical tools connected to it, will interfere, as is the case if you simply place the extension cord on the floor.

However, the problem is that not all manufacturers make canopy holes on the back wall of their extension cords, thanks to which they can be hung on the wall.

For example, on this extension cord there are such canopies.

But this one doesn’t have them.

Of course, you can make canopies on the back wall of the block yourself by drilling holes in it. However, this is often dangerous because it can lead to damage electric shock, and sometimes not very convenient.

I found a simple way out of this situation by making wooden canopies from small planks on many of my extension cords.

Moreover, making such a canopy is quite simple.

To do this, you will need the following materials:

two small screws;
as well as a small board, 10-12 mm thick, one and a half to two times the length of the extension block and slightly wider.

Tools you will need:

jigsaw with file;
electric drill with a wood drill bit, 20-25 mm in diameter, and a metal drill, 4 mm in diameter;
and also a screwdriver.

The procedure for making a canopy

First, from one end of the blank board, in the center, you need to drill something like this through hole, feather drill for wood.

Then, stepping back a short distance from the edge of the circle, drill the previously drilled hole, drill another hole with a diameter of 4 mm.

The exact same hole needs to be drilled at the other end of the board.

In this case, the main thing is the distance from the edge of the circle to the top hole.

And from the end of the board to the bottom hole they were the same.

After this, using a jigsaw, you need to cut the grooves to the upper and lower holes.

And then you can round the ends of the board, although this is not necessary.

The canopy board itself can be slightly processed sandpaper and paint or varnish, although this is also not necessary. Well, after that, all that remains is to secure the extension cord to our canopy.
To do this, you need to disassemble the block into two parts by unscrewing the screws and removing the cover with sockets and terminals.

And at the ends of the rear wall of the block you need to drill two holes with a diameter of 4 mm, and screw it to the canopy with small screws.

After this, the block can be assembled.

And now our extension cord with a canopy is ready!

Using an extension cord canopy at work

After this, you can easily hang it on the wall by screwing two screws into it. Moreover, you can hang the extension cord either vertically.

Or horizontally, which seems more convenient to me, especially for an extension cord with a switch.

By the way, this extension cord constantly hangs on my porch wall, near the main outlet.
I must say that this is very convenient, since the main, quite powerful socket is used to connect a large load, for example, electric welding. And in the event that I need to connect several power tools, I just use this extension cord, connecting it to this outlet.

If this extension cord is needed in another place, it can be very quickly removed and then hung back.

So using extension cords with such awnings is very convenient!

Well, that's all for me! Goodbye everyone and good luck in the new year!

Modern housing consists of many communications, where electrical wires occupy a leading place. They connect not only numerous light sources, but also all equipment, from household to digital. Such an abundance of cable can create an unattractive picture, and if there are small children in the house, it can also be dangerous. To avoid any troubles, when planning a renovation, you must immediately determine where and how to hide the wires in the apartment. Let's look at the most common options that are very popular.

Internal placement

When it comes to major renovations, it is best to hide all communications so that they do not spoil the aesthetic appearance.

Wall

This technology can be used when wallpaper is already hung on the wall. To do this you need to follow simple algorithm actions:

The wallpaper is carefully cut with a sharp knife and bent to the sides, secured with needles.
By using construction tools make a groove where the wire will be hidden.
Place the cable in the resulting recess.
The groove is sealed with plasticine or covered with plaster.
When the solution dries, coat the wallpaper with glue and glue it in place.

Floor

No less popular is the placement of wires on the floor, or rather under it. So simple, but at the same time in an original way, you can quickly disguise the wires. Once you choose this option, you have several options.

Special plinth. When visiting a hardware store, pay attention to models of skirting boards with a special niche for cables. The central part will be easy to remove, and wires can be laid in the recess. This method is convenient and universal.
Disguise to the floor. During the repair work Using a hammer drill, a recess is made in the floor, in which communications are laid and then filled with cement.
Cement strainer. Leveling the floor is a mandatory process in almost every apartment. To do this, you need to stretch the wire in a corrugated structure, lay it on the floor and pour a regular cement screed on top.

Ceiling

You can even hide the wires on the ceiling, and this will be easier to do than with a wall. There are also several options here:

Installation of a decorative niche made of plasterboard, which runs along the entire perimeter of the ceiling. The resulting gap can accommodate a huge number of wires. Experts recommend connecting all communications into one common highway.
A stretch ceiling also allows you to hide the wires, but you just need to think about this before the canvas is stretched. The placement method will not make any difference.

Placement behind a suspended ceiling Please note! To give the ceiling with a niche aesthetic and original look, equip it with lighting.

External camouflage

If you don’t want to disturb the created interior and add more work to yourself, then you can use no less interesting ways camouflage.

Tree branch. Even a small but extra piece of cable can be easily decorated. To do this, a tree branch is formed, which is decorated with homemade leaves, flowers and birds. An original idea will update the interior and enliven the room.

Trees. If the length of the excess wire is too long, then do not rush and cut it. It will be enough to buy special fasteners, look on the Internet for a suitable silhouette and form it on the wall.

Scenery. More can be considered complex options. So you can “draw” on the wall original panel. The main thing is a clear contrast that will highlight the idea.

Art object. Since we are talking about electricity, we can do original design ceiling in the form of a giant light bulb. This design is fixed to the ceiling.

Power station. To decorative element performed several functions at the same time, you can depict a simple power plant on the wall, with the help of which parents can teach their children the basics and principle of operation of the power plant.

Highway. The process is more complex and painstaking, and will also require free time and desire. To create an interesting piece of furniture, you need to cut out all the components from cardboard and, if desired, paint them to create a colorful object. You can purchase special blanks. This way you can easily disguise the wires from the TV.

Fence. Any wires can be secured to the top of the baseboard. But in order to disguise them, you can cut out small blanks in the form of a fence, which is fixed to the baseboard using double-sided tape. This original idea for a children's room, while the fence can be painted in different colors or one specific one.

In addition, communications can be easily hidden behind the following items:

high houseplants;
properly positioned furniture;
door frames;
carpet covering.

Note! It is best to sketch out the wire placement plan on a piece of paper in order to think through and use several masking options.

Computer

The largest number of cords are located around the computer desk. Here, in addition to the computer itself, there may be other devices that require connection to the mains. All this leads to the presence of not only tangled wires, but also carriers. To decorate them, just use your imagination:

Using clips, screws, double-sided tape, all wires are secured under the table cover.
Any shoebox will contain a large number of wires that will come out of specially made holes.
The sewn cover for the extension cord is simply fixed to the cover desk and thus it will not get underfoot and disturb the user.
A simple cover is also made along the contour of the back of the table, along which the cords will run down to the sockets.
To keep the wires twisted into one whole, you can tighten them into a hose, which will quickly remove the chaos behind the wall.
To prevent device connectors from getting lost, you can use simple stationery paper clips that are attached to the side of the tabletop. When it comes to Internet cables, experts recommend switching to modern and innovative technologies, that is, use wireless network– Wi-Fi. This will allow everyone to connect to the Internet no matter what room they are in.

Extension cable box Please note! The shoebox idea can also be used to store chargers for phones, tablets and digital cameras. In this case, they will all be in their places and will no longer get lost.

During the masking process, each type of cable must be marked on both sides. Even after a few years you will not get confused in large quantities wires and quickly find what you need.
Wires that are used to transmit data or signal (computer, antenna, audio and Internet) must be connected separately from cables with alternating current networks. This will reduce the level of interference and noise.
The power cable should be short; the longer it is, the higher the risk of electric shock and injury. Even a child or animal can damage it while playing.
The fabric braid should not be bent, as the fabric can catch fire if there is a small tear and also quickly lose its attractiveness.
The specialty store offers a wide range of special decorative boxes, in which you can hide wires. Original design It will easily fit into any room interior and will not take up much space.

A device for neatly placing wires. Please note! Buy and cut required amount wires after the fact, so that later you don’t have to think about where to put the excess and how to decorate it.

If necessary, you can implement the most unusual and extraordinary ideas for masking wires in the apartment.

stroysvoimirukami.ru

How to hide wires

The equipment in the apartment greatly simplifies the life of its owner, but as it becomes more numerous, the problem of wires becomes more complicated. If you are already starting to panic, looking at the wires for your computer, charging your phone, laptop, tablet snaking across the floor and under the table - do not despair, in this article we have collected 7 for you the best ways how to hide wires beautifully and put an end to it!

1 Tie and immobilize!

Cables and wires, at least most of them, are located in approximately one corner and rarely move. Nevertheless, the computer wires gathered in thick balls under the table, the eternal “noodles” behind the TV, constantly get under your feet, make it difficult to clean, or even completely fall out of the connectors at the most inopportune moment.

How to hide the wires and secure them at the same time? Try using construction ties for this: they can be disposable, they cannot be removed without cutting them, and they can be reusable. They cost pennies, but they can be used to assemble wires into bundles and attach them to the wall.

**highlight: The soul strives for beauty even in the prosaic theme of seeing off? Buy decorative ties! Leaf Ties similar to leaves can be ordered online. Similar “Wire Blooms Cable Clips” will make it possible to fix the cable to the wall.

2 Binder to help with hiding wires!

The name of this large office clip is not familiar to everyone, nor is its other side. It can not only hold papers, but also become a good ally in the fight against wires.

Use them to secure wires to a table or wall, and remove them whenever you want in one motion. Secure them on the table and thread a USB cable or any other cable you use frequently through them, and they will never get lost or crawl away.

3 Velcro will help you hide wires: simple and creative.

It is convenient to tighten the wires with special Velcro, the same as on clothing. You can buy them or make them yourself; you can find materials for them in a craft store.

4 Hide, cannot be left.

There are many options for hiding wires that move one way or another, but what to do with those that lie in one place almost all the time?

In this case, you need to buy a cable channel, often in construction stores they are sold combined with baseboards. They will perfectly hide several wires, even if they are quite thick.

Although they also have a disadvantage - they must be installed after first getting rid of the old baseboards, and the wire installed in them cannot be easily removed. Fortunately, there are alternative solutions.

This decorative fence is convenient, looks great and is easy to make. All you need is plywood (thick cardboard or plastic will also work), double-sided tape and cutting tools.

5 Incubator... for charging.

Chargers and power supplies from various gadgets cause no less trouble in the house. Every year their number grows, and sometimes finding the right charger takes as much time as the process of charging the battery.

A charging box will help you forget about this and no longer meditate over a tangle of tangled wires while removing the necessary charger from it.

The field for creativity here is huge - only your imagination and... fire safety can limit you. Yes, you shouldn’t neglect this parameter and try to fit all 15 power supplies into a small box: they can overheat and cause a fire, so don’t skimp on space in the “charging incubator.”

Inside the box is an extension cord for several inputs. It takes a couple of minutes to do this, but then you can charge several devices at once without cluttering the table. A shoe box works well as a base.

There is another option - sew a holder for chargers. Design and quantity seats, again, only your imagination determines.

A “single” bag for charging a smartphone made of fabric and similar with increased rigidity (the shape of a lotion bottle, lined with fabric).

6 How to store wires.

When you bring in perfect order all the wires are on the table and nearby household appliances, it’s a good idea to know how to store wires. It could be a lawn mower cord, love. New Year's garland, or even headphones, which tend to get confused with phenomenal tenacity.

The wiring harness can be inserted into a cardboard tube from paper towels or toilet paper. Each one should be labeled and stored in a large box without fear of them getting tangled. Instead of such tubes, you can use pipe insulation (sold in hardware stores).

Headphones can be wound around an old bank card, and a garland can be wrapped around big piece cardboard

7 How to hide wires for a computer and more.

We deliberately placed this method of taming wires at the end, since it includes all the previous ones. How to connect wires so that you forget about them for a long time? Make them one with the furniture! Read how to fix bad smell ourselves.

For example, the order in the wires under computer desk can be aimed by fixing the extension cord, electrical and signal wires “upside down” or vertically. You don’t need any special skills for this, just self-tapping screws and a screwdriver are enough. And if you don’t want to spoil the furniture, pay attention to the various Velcro clips, of which there are many in hardware stores.

Following these simple tips, you can tidy up your wires in no time, while showing your creativity. Read: How to make it yourself decorative candles– 10 ideas.

How to attach a cable duct to a concrete wall

During the construction of a house, electrical wiring is installed in a hidden way, under the plaster. Complete replacement of electrical wiring is usually carried out during overhaul. In this case, grooves are made in the wall, into which the wire is laid.

But what to do when there is no opportunity or desire to engage in dusty wall slitting? Or do you need to connect a recently installed powerful electrical appliance, such as a water heater? In this case, many choose open method laying of electrical wiring, and fastening to the wall is carried out using a cable channel.

Types of cable channels

Several criteria are used to classify a cable channel:

Size. There are small products for laying one small-section wire or box large sizes, designed to mount up to eight conductors of various cross-sections on the wall;
Material of manufacture. They produce aluminum, steel and plastic structures. More popular for indoor installation plastic models, and fastening steel and aluminum boxes is more often used when laying electrical wiring along the facade of a house;
Location. The cable channel can be fastened in several places. The design of the product is maximally adaptable depending on the installation location. There are plinth, parapet, main and floor models.

Note! By color design The cable channel most often has a neutral White color, suitable for any finish. Models that imitate a wooden structure are also popular.

Installation technology

The main advantage of cable channel for open wiring– this is ease of installation. At the same time, the structure can be fixed on any surface: wall, floor or ceiling. The surface material is of greater importance: the method of best fastening depends on this. Let's consider the main installation options, as well as the types of surfaces to which the channel cable is attached.

Surface marking

Before you begin to attach the cable channel, you need to make markings on the surface: the location of the electrical wiring boxes is marked on the wall. This can be done using a pencil or chalk and building level. It is important to maintain horizontal and vertical lines, since after installation the unevenness of the gasket will be evident.

Self-tapping installation

To secure the box to a wooden wall, use ordinary self-tapping screws. The recommended length is 2-3 cm. This method is suitable for wooden houses, baths and other buildings. Self-tapping screws are also suitable for walls covered with wooden clapboard.

When performing installation, holes are pre-drilled in the bottom of the box, into which self-tapping screws are then screwed. In plastic structures, holes can be made directly with a self-tapping screw during fastening. The optimal distance between installation points is 30–50 cm, depending on the expected load on the cable channel (the number of electrical wires placed in the box).

Fastening with dowels

Installation of cable channels on concrete surface requires a more serious approach and additional tools. This will require plastic dowels and a hammer drill or impact drill to make the holes in concrete wall. This method is suitable for installing any profile: both metal and plastic, in interior spaces or outside the building. The order of work is as follows:

Holes for fastening are drilled at the bottom of the box. The distance between them, as in the previous version, is 30–50 cm;
Then the cable channel is applied to the wall along the previously marked line;
Using an awl or nail, the location of the fasteners is marked on the wall surface;
Then, using a puncher, holes of the required diameter are drilled along the marks in the wall, into which plastic dowels are driven;
After this, all that remains is to secure the profile using self-tapping screws.

To secure the electrical wiring box to a concrete surface, you can also use dowel nails, which are driven in with a hammer. But this option has a significant disadvantage - if it is necessary to move the structure, certain problems arise with dismantling such dowels.

Glue method

Another option for securing the cable channel is to use mounting adhesive for fixation. Most often, the adhesive composition “liquid nails”, produced under the Moment brand, is used for these purposes. This glue is available in tubes under mounting gun or in ordinary tubes for manual application.

The adhesive installation method is used for attaching cable channels to plasterboard, PVC wall cladding ( plastic lining or panels), as well as in bathrooms on ceramic tiles. It is worth noting that only plastic wiring boxes are suitable for this method, since their weight is minimal. It is also desirable that the number of wires laid in the cable channel be minimal and do not create significant loads on the structure.

The technology of the adhesive fixation method is as follows:

An adhesive is applied to the back of the profile. To ensure maximum adhesion area, the glue is distributed in waves;
Then the cable channel is carefully applied to the wall along the marking line and immediately removed;
After 2–3 minutes, when the glue has begun to dry, the strip is reapplied and pressed firmly for several minutes.

After the adhesive has completely set, additional fixation is performed in problem areas. For fastening, use small screws or hammer nails.

To facilitate profile connection, use those offered by the manufacturer additional elements: T-shaped and corner structures, strip connectors, various bends and other accessories.

To install sockets and switches, it is best to use overhead versions of these products or use box models with built-in structures.

Separately, we note that the installation of external electrical wiring is carried out last, after all finishing works.

voltland.ru

How to fix the wire to the wall?

Wires are laid in different ways. Or they make a groove in the wall and lay it there electrical wire. Can be placed on top of plaster, but not on top paper wallpaper. They secure it with special brackets bought in a store, or by cutting metal plates, nailing them, placing a wire on them and tightening the ends. Wiring is often placed in beautiful cable channels so that they do not spoil the appearance of the room.

If the wire is stationary and does not involve periodic movement, then it is better and safer in a cable channel. These are plastic boxes made of low-burning materials, having both a neutral white color and many others - wood, ivory, etc. In such a box, the cable does not break or get pressed, and the maintainability of the entire network increases.

They used to drive a nail, but those days are gone. In places where wire is sold, special fasteners for wires are available for sale. They are selected based on the thickness of the wire and look approximately as follows

Very easy - just stick it on! You can even use wallpaper glue! And if it is not available - your own saliva, after eating eggs or even oatmeal! Eat a bowl of oatmeal (or pearl barley - it doesn’t matter), then generously moisten the wire and the wall with your saliva and calmly stick the wire to the wall - if your saliva is not viscous enough, you can drive a nail or use a hammer drill, the main thing is to choose the right time to pin the wire to the wall! The most effective time is after midnight and certainly in the waxing Moon Phase! Calmly, without nervousness, turn on the hammer drill (you don’t have to slobber on it) and, having estimated the position of the wire, as you please, push it into the wall! The main thing is not to make a mistake in the Moon Phase! Otherwise, the wire may stick in fragments and fall off the next day! And this is a completely different story! 🙂

In addition to all these methods, you can use regular nails 20 millimeters long. Otherwise, hammer in half the path of nails along which you want to lay the cable. Using pliers, bend them 90 degrees. Hold the cable and drive the nails into the top one at a time. The result will be fastening in the form of staples.

Wires and cables can be attached to the wall with special wire fasteners, but this will not look very neat.

A more civilized way is to lay the wire in cable channels that are attached to the wall and only then the wire is laid in them.

There are several ways to secure the wire to the wall. It all depends on the purpose of this fastener, permanent or temporary, on the purpose of the wiring being laid, on the requirements for its appearance. If the wire is attached to a concrete or brick wall, it is best to use cable channels, the choice of which in the store is very large, of various sizes. They also have special corners, adapters or plugs, like for baseboards. It looks aesthetically pleasing and is quick to install. The cable channel is attached to the dowel-nails using a hammer drill, after about 40-50 centimeters. For wooden wall there are more options, these are the same cable channels, plastic clamps shown in the earlier answer, homemade clamps made of tin (they are first cut into thin strips, then nailed to the wall along the cable route, and then lay the cable and clamp the clamp on both sides), special retro porcelain insulators, which used to be found in every home, but now they have become a vintage piece of furniture. Often they try to hide the wire in plastic skirting boards, if they go along the wall.

info-4all.ru

How to remove wires in an apartment and hide them creatively. MASTER FROM GOD

Every person strives for perfection. Trying to create something beautiful around himself. Sets up his home. Tries to make it warm and cozy. Carrying out repair work, creating beautiful interior, arranges furniture and equips the room with equipment. The operation of modern technology is impossible without wires. Television, electrical and Internet wires often stretch along the perimeter of the entire room, thereby causing a lot of trouble. Owners often stumble over them. In addition to making life difficult, they also greatly spoil the design of the room. What to do in this situation and how to remove the wires in the apartment that get tangled under your feet?

An easy and common way to remove wires in an apartment is to hide them in the floor plinth. Its main feature is that it contains a space intended for laying wires. You can buy it at the market or at any construction supermarket. The plinth is attached to the wall using self-tapping screws and dowels.

Cables stretched along the wall are hidden in the plastic channels of the baseboard. Floor skirting boards come in different colors and sizes. Therefore, you can easily choose the right baseboard, which will allow you to hide all communications in it, and at the same time look nice.

After laying the existing wires, the channel cavity is closed with a special decorative strip. This method is distinguished by its reliability and cable protection is guaranteed from animals that like to scratch and chew everything.

Another method will help you hide wires in the floor. When conducting construction work leveling the floor using a screed. The wires are bundled into a special sleeve and filled cement mortar. When hardened, the cords are conveniently hidden underneath.

How to remove wires on the wall in an apartment

When carrying out repair work, the wires are deepened into the wall. This is done with a grinder. Two grooves are cut into the wall, after which a part of the plaster between them is knocked out with a hammer drill. This creates a groove. All communications are laid in it and covered with alabaster. It dries quickly and holds them in place. The same applies to the places where the sockets will be located.

How to remove the wires on the wall after completing the repair? Boxes will solve the problem. You need to attach them to the wall with glue or screw them, and then insert the cable into them and slam the lid.

If the socket is located close to the door or you do not know how to remove the wires lying in doorway, then door trims are used to disguise the cable. It is necessary to remove them and place the wires there and put them back.

You can easily remove wires in your apartment using hanging or stretch ceiling. A metal, wooden or plastic frame is specially made and fixed under the ceiling.

The cables are assembled into a bundle and laid inside the frame or on top of it.

To keep the wires together, you can use insulating tape or plastic clamps. If there are few wires, use a plastic sleeve. Then tension or suspended ceiling will hide everything. But if you cannot remove the wires yourself, you can contact trusted professionals and they will help you.

How to remove wires in an apartment using furniture

You can cover the wires in other simple ways. With the help of furniture. If there is a lot of furniture in the room, you can arrange it so as to hide the wires as much as possible. At the same time, nothing changes radically, and the room after such a rearrangement will look different.

Availability of a personal computer and org in the house. technology, also implies a large accumulation of wires at the table.

The right solution would be to purchase a special plastic box for cables. It fits wires and extension cords perfectly. When buying a simple box, you can hide it under the table, but if it is bright, use it as a decorative addition.

How to remove wires in an apartment - creative ways

If you wish, you don’t have to hide the wires at all. You just need to include a little imagination and ingenuity. And the interior design of the room will change beyond recognition.

Do not rush to cut the length of the wire. Its size can serve for creative ideas. Creating an ornament, pattern, bird, dragonfly. Cords can be hidden by using climbing plants. Throw a twig along the cable and the wire will turn into a decorative element. It will look beautiful, and the presence of fresh flowers will refresh and add coziness to the room.

Decorative staples are also sold. They are somewhat different from simple ones in their appearance. Decorated with birds, flowers and all kinds of figures. With their help, you can make a tree from ordinary wire, with a bird sitting on it, or a flower, with a beautiful butterfly.

If such staples cannot be found on sale, you can use them instead vinyl stickers. With their help, create a composition and the cable will become part of it.

Using the advice of the article on the site, everyone will be able to choose for themselves an acceptable method through which they can achieve results. And the problem of how to remove the wires in the apartment will disappear forever.

You are here now - home page - All about repairs:

When you are going to hang something on the wall, this is not a question at all!

You will need a hammer drill or impact drill. A couple of dowels. Level, hammer, tape measure.

If it is a shelf or a cabinet, then place it in that place and approximately mark the level of the hole. Well, then it’s quite simple, we measure the distance between the holes on the shelf or cabinet.

We mark the first hole, take a level and draw it, take a tape measure and set the distance. The intersection of the level line and the distance on the tape measure will be your second hole!

If there are several shelves or cabinets, then we do this:

We start either from the extreme right point or the extreme left point, drill, hammer in a dowel, tie a thread, and level it. In the place where a person holds the thread, it needs to be secured somehow. You can drill and attach it to a dowel only if the hole from the rough dowel is either hidden by a shelf or a cabinet.

An ordinary dowel 6 x 40 will withstand a minimum of 50 kg per cut in a concrete wall. I think that you won’t have more than 100 kg in one closet!

Why is all this, how to hang a shelf, or how to hang a closet, such a simple operation that it’s even somehow boring!

But here's what I wanted to tell you about.

How to hang it accurately the first time?

How to hang something whose holes are not directly accessible!?

Imagine a situation where you measured, hammered a nail, and didn’t hit the right size. various reasons, but it’s already impossible to drill nearby!?

Has such a situation ever occurred!?

Since I worked a lot both in construction and as a carpenter and joiner, I had to see a lot!

And often this very situation turned out to be practically unsolvable the first time!

But there is a way that is ingenious, like all the simplest things! And I remembered this method when the need arose to hang an extension cord!

Hang your computer extension cord on the back of your desk the first time and exactly where you need it! The top tabletop extends slightly beyond the backsplash, which is why we have a stopper!

We need to make a template.

1. Select self-tapping screws so that they fit freely into the hanger hole.

2. In this case, I had thin cardboard lying around.

ATTACHING THE EXTENSION

It is more convenient than a simple sheet, because the screws will hold better there.

3.Insert the screws and move them to the extreme point of the hanger,

4. Take the cardboard and, aligning it along one of the sides, press on the cardboard so that the screws appear on our side.

5. We take out the cardboard with self-tapping screws and place it in the place where our object should be located, in this case the extension cord.

6. We wrap the screws, tear out the cardboard, and adjust the screws to the height.

7. Attach the extension.

This is what we got, quickly, simply, accurately and right the first time! The story turned out to be 10 times longer than the process itself!!!

How to hang up a router.

Using absolutely the same technology, we will attach the router in the place where it is needed on the back panel, or on the wall, but the first time.

In this case, ordinary paper was used as a template!

Here is our router hanging on back cover table! Very simply cheap and cheerful!

Before installing electrical wiring in new apartment or before replacing the wiring during a major overhaul, any owner is faced with a choice of how many and what kind of sockets he needs to install in each room. IN modern apartments sockets are rarely installed one at a time; usually two, three, and in some cases even four electrical sockets are placed side by side. For example, at a workplace with a computer it is better to install 3-4 sockets, otherwise you will not be able to do without an extension cord.

Practice shows that there are never too many sockets. If we need to install two sockets side by side, then we have a choice - install two single electrical sockets in a two-post frame or one double electrical socket. The Florence series features double rosettes and multi-post frames, so both options can be implemented. What to choose?

Double sockets are designed to Instead of one old socket, one double socket could be installed into the existing socket box.
Ideas for the home: how to hide wires

This allows you to double the number of sockets when renovating an apartment. This is why double sockets were developed.
The price of a double socket is less, than the price of two single sockets in a double-post frame, let’s see this using the example of white or beige sockets from the Florence series.

1. Price calculation for two single sockets in a two-post frame

2. Price calculation for Alternative option– for double socket

You can install the wiring so that powerful electrical appliances are connected to each single socket, i.e. so that a current of up to 16 A flows through each. But for this, it is necessary that the sockets are either powered through two separate lines with cables of a standard cross-section for connecting sockets (2.5 mm2), or powered in series through a cable of a larger cross-section. As a result, it is possible to ensure that the total maximum current, which can flow through two single electrical outlets would be 32A. This cannot be done by installing a double electrical outlet.

To summarize, we can say that double sockets are indispensable if we are faced with the task of increasing the number of sockets in pre-installed socket boxes. This is mainly true when replacing sockets during cosmetic repairs, if the wiring is not replaced with the installation of new socket boxes. Single sockets under a multi-post frame look more aesthetically pleasing than double sockets and give greater freedom of choice. This option is suitable for a major renovation of an apartment with replacement of wiring or for furnishing an apartment without finishing in a new building.

All extension cords and surge protectors (I still don’t understand what their difference is, except for the treasured general shutdown button, which no one uses anyway) have one, very significant, in my opinion, disadvantage: they lie loose. And if sometimes this is still an advantage, for example, putting it aside when you vacuum, or moving the system unit away, then more often this is not the case. And at the most inopportune moment, when your hands are busy with something and your vision is limited by something oversized, you hook your foot on the extension cord and pull it out of the network. In the best case, the download of the file, which has already lasted 1.5 hours, is interrupted by 98%, or the transfer of music to the phone will have to start all over again. Well, in the worst case, if the plug of the electrical appliance does not fall out, but the wire breaks, it is simply unsafe.

So I, having suffered with all sorts of extension cords, wondered: what prevents it from being secured, not even on the floor, but higher up. After all, it’s both more convenient and safer. But here’s the thing: I didn’t find anything like this on sale (although maybe I was looking in the wrong place), but the preliminary outlines of this simple device have already begun to emerge:
Small, compact, but convenient;
On a clamp so that you can always rearrange it;
So as not to be conspicuous, but always at hand.

So, following the principle of car tuners: “if you can’t buy it, build it yourself,” I set to work. By the way, for reference: it took no more than 15 minutes, even taking into account the fact that I was a “pioneer.” Such a creation will take you much less time.
First of all, I bought two external sockets without grounding, single,

and double (I told you that the requirements for the extension cord began to emerge).

And definitely with back wall, otherwise it would have to be done.

But I simply found a clamp (plastic, for fastening the flexible shaft of a drill) in my stash. It’s like a “grand piano in the bushes,” so I didn’t have to buy it. Although, as practice later showed, it is not at all difficult to find and buy something similar, and there is an abundance of something similar in construction markets and supermarkets.