DIY plaster figures for the garden. DIY solution for garden sculptures

To realize this truly amazing design idea You will need very little: desire, effort and, of course, imagination. And if the master has the talent of a sculptor, then real works of art can come out of his hands.

Preparation of solution for sculptures

For using gypsum or concrete. Concrete is made like this: mix cement and sand in a ratio of 1 to 3. Then water is added in small portions, making up about half the volume of cement. The kneading process is similar to making dough.

To make the plasticity of concrete higher, PVA is added to the usual composition. Moisture resistance finished product increase by adding liquid nails to the mixture.

The readiness of the solution is checked as follows: squeeze a little mixture in your fist, open your palm and make an indentation with something. If water appears in the hole, it means there is excess water in the concrete. In this case, add cement to the mixture.

Sometimes the piece immediately begins to crumble. This means what needs to be added to the water solution.

Molding method for making figurines

Even the most inexperienced people in modeling can make a mushroom clearing or a cheerful forester in a mushroom hat out of concrete or plaster, ladybug or a turtle walking along. Using the molding method, it is easy to make a concrete hemisphere. After a short extra work over the blank, adding details and coloring, the master will receive a cute figurine to decorate his area.

You can use half a rubber ball as a mold to create a hemisphere. To do this, cut it in half and put it in a bowl of sand. Only then can you begin to fill the form with concrete or plaster. If you place the rubber hemisphere on the floor or ground, you will get a recess on the bottom of the dried part.

A basin can be used to form turtle shells and some types of mushrooms. But to make it easier to remove the part, it is best to put polyethylene on the bottom of the mold.

Making mushroom

After filling the hemispherical mold for the mushroom, you need to place and slightly drown a plastic bottle with the neck cut off into the concrete.

The eggplant is also filled with the mixture. But first, a metal rod should be installed in it so that it protrudes slightly above the cut. Then it will be convenient to install the figure vertically, sticking it into the ground.

After some time, when the concrete in a semicircular shape sets, the bottle must be removed - there should be a recess. The ball is removed from the concrete cap part. If cracks or voids appear on the surface of the future cap, they can be covered with mortar or putty. The part is dried a little more until it is absolutely hard.

You also need to remove the bottle from the leg. It can be cut with a sharp knife. Cracks and voids should also be filled with putty.

Since mushrooms usually grow in families, you can make several fillings at once. different sizes. You will need balls of slightly smaller diameter. Or you will need to pour concrete into the other half just below the previous level. You can use disposable half-liter glasses as a mold for the stem.

When the parts have acquired the necessary hardness, they are coated with a primer and joined into a common shape. Then, after about an hour, you can start coloring. To give the figurine shine, the craftsman can coat it with varnish.

Making a turtle

After removing it from the mold, you need to draw a design on the turtle shell with a stick. As long as the part is not completely dry, this can be done. If the drawing turns out to be of poor quality, you can apply a thin layer of mortar or putty and apply hexagons to the shell freshly, or lay it out with pebbles, and make a mosaic from pieces of glass.

If you wish, you can add more paws, a tail, and a head to it. But then, already during pouring, metal pins are inserted into the solution. Later, limbs and a neck with a head will be stuck on them.

Frame sculpture

Casting large figures is quite difficult. The more difficult it is to find the required form. Therefore, frames are used to create such sculptures.

Materials needed to create a frame sculpture

If you decide to make your own concrete figures, the master needs to stock up

concrete;
aluminum wire or mesh for the frame;
plastic film;
foam plastic, old buckets, bathtubs, metal barrels to lighten the weight of the figure and reduce the volume of concrete used;
spatula;
spray with water;
paint used for exterior use;
thin rubber gloves;
a mask that protects the respiratory tract from cement dust and paint fumes;
saw with diamond wheels for processing the finished figurine.

Man-made boulder stone

Almost anyone can make such a decoration for a site. And the boulder on the site looks quite exotic. The stone looks especially beautiful near a body of water, a swimming pool, in, along paths.

Seats for benches can also be attached to boulders. It can serve as the foot of a table with a tabletop that seems to intersect its upper part.

Wire frame manufacturing process

The frame of the stone is made from wire.

The inside of the frame is filled with bags and foam. You can also use construction waste, empty glass bottles, empty buckets, basins, barrels. This will reduce consumption cement mortar and will delay the process of its “falling through” into the frame.

Prepare a cement solution.

Concrete is placed on the frame using small cakes.

After some time, the first layer of cement will set. Then you need to make the solution thinner and coat the stone again, smoothing out the unevenness with a spatula.

Then the top of the stone is wrapped in polyethylene and left to dry a little.

When the top of the stone has set, the workpiece is turned over and the base of the boulder is coated with the solution.

Making a boulder using burlap

Burlap is dipped into the liquid concrete solution and squeezed out. Then it is placed on the frame.

The workpiece is coated with thick concrete. The algorithm for applying the solution is repeated - the figure is stuck on top with small cakes, just like on a wire frame.

The edges of the burlap are folded inward.

After drying, the stone is painted and varnished.

Video tutorial on making a frame vase from concrete

More complex sculptures are made using the same technology. Just to work, the master will need the talent of sculpture.

Even inexperienced gardeners who want to put their soul into their cozy home and yard can make beautiful garden figures from plaster with their own hands; the master class will help you understand all the intricacies. The manufacturing procedure itself is simple. Before starting manipulations, you need to clearly define the idea and character in order to make the garden more comfortable.

Show all

Learning to create a master class

A master class on making stylish figurines will help you realize exclusive ideas and create a garden sculpture with your own hands. Without special education or skills, you will not be able to create a truly exquisite antique sculpture, but anyone can make a miniature plaster figure.

Original compositions are suitable for creating decorative dacha specimens. The cat looks cute when it sits near the flowerpots. This animal can carefully watch its favorite mouse walking along the bright summer grass. An extravagant mixborder filled with flowers can also be an option for a garden craft. It will be perfectly complemented by a snow-white marble angel. Such sculptures can recreate a romantic or ancient atmosphere and add style to a summer cottage and garden. Using the master class, you will be able to get a garden beacon.

To make a decorative and original craft, you will need to prepare plaster or ceramic containers. There should be 3 of them, all of different diameters and volumes (small, medium, large). They definitely need to have pallets. You also need to use liquid nails and paint. white as a basis. A red tint is needed for the windows, and a blue tint for the frame. In addition, the following materials are required:

tassels;
masking tape;
measuring tape;
simple pencil.

To make the beacon look as natural as possible, a flashlight is attached to it at the top. In inner part Each container should have a tray attached. All pots due to use liquid nails put on one another in a certain sequence. Most small vessel is located at the top, and the bottom will be a large pot.

Next you need to fill a plastic cup with paint. of blue color(A little). This will allow you to thin the white paint. The result should be a heavenly color in which the borders of the product will be painted. The connected pots are painted. Next, attach a miniature lantern. It will become an imitation of an observation cabin. The created craft is best placed in a spring green meadow or in a garden among ornamental shrubs, near the lawns.

Original bath made of plaster or cement

If you want to see unusual garden figures on your site, you can make a bird bath. Externally, it looks like a colorful rhubarb leaf. Multi-colored gypsum leaves are best placed near shrubs, trees, and along garden paths. If available in the garden or on personal plot growing rhubarb, burdock with large leaves, all that remains is to make the following preparations:

A leaf of any of the above plants should be placed front side, and pour liquid cement mortar on top of it. After the solution dries, the sheet with sand is removed. It will turn out to be a bathhouse.

For greater beauty, you need to lay out newspaper pages on the tabletop, prepare a large leaf of a plant, cement and sand. Pour sand onto newspapers and place the sheet on top, wrong side up. The sheet should be neatly straightened, its position should be well fixed; to do this, you need to press it with your fingers.

Such cement crafts can be made more perfect in appearance by creating decor from pebbles. Bird baths made in bronze and gold shades look stylish and elaborate.

To create a product from cement with your own hands, you need to dilute the dry material with water so that the mixture has the consistency of thick sour cream. The cement is poured onto the rhubarb leaf carefully; it should be covered over the entire area with the solution. The workpiece should harden.

You can do the following with a cement sheet:

decorate with bright colors;
cover with lime;
leave in natural form.

The finished sculpture needs to be strengthened. To prevent the cement from being washed away by water, the top of the bathhouse is covered with a thin layer of soil and a mixture that repels liquid.

Irresistible blooming hand made of plaster

The next master class will help you make a popular homemade garden figure in the form of a compact flower bed. It looks unusual because it is shaped like a hand and is made of plaster.

To make a hand you will need the following:

gypsum;
several flower pots;
rubber gloves.

At the first stage of manipulation, the rubber glove is filled with a solution of plaster and water. The mixture should be thick. The glove is placed in a flower pot, where it should harden thoroughly. The fingers of the rubber product are placed so that there is space between them inside. Then a small amount of soil for the plant is poured there. When the solution has completely hardened, cut off the glove. The result is a sculpture in the shape of a hand, which will stand not only for beauty, but also serve as a pot. Similarly, the desired number of exclusive flowerpots is created.

You are allowed to decorate your hand with paints different shades, you can leave the natural color.

Only dwarf crops are planted in such a flowerpot, preferably with a long flowering period, so that they delight with their beauty throughout the summer months. Such garden figures are usually installed in flower beds, where they look very appropriate.

Sculptures in which young and tenacious plants are planted have a decorative appearance. They are placed directly on the ground in the garden along the path, on hanging shelves made of wood, window sill, porch.

Making a miracle mushroom

This master class will give you the opportunity to make gypsum mushrooms. The materials and tools are as follows:

gypsum;
construction adhesive;
pencil;
compass;
acrylic paints;
beads for decoration;
waterproof glue;
thick needle or wood cutter;
soap;
brush;
sunflower oil;
water;
cling film;
unnecessary dishes or plastic containers for molds.

The fungus will consist of a base, a stem and a cap. Before starting manipulations, you should prepare the mixture:

sunflower oil (1 part);
grated soap (2 parts);
water (7 parts).

The mass is spread on a film that is used to wrap the mold container.

The plaster is not diluted immediately. It hardens quickly, so you first need to prepare the mold. The packaging with the material contains instructions that should be followed. A cut plastic neck would be an excellent shape for the mushroom stem. The mold is well lubricated with the mixture. A smaller container is placed in the center. It will help make the leg empty inside.

The plaster is poured into the mold, the smaller vessel is placed in the desired position using a stone or other object. Using a knife, after the material has hardened, take out a small bottle. A deep plate is used as a shape for the hat. The steps are repeated similarly to the procedure for creating a leg. When the plaster begins to dry, a leg is inserted into the middle. After the material has hardened, the mushroom is removed from the mold and the film is removed.

When making a base, it is better to give preference to a removable option. The form must be larger for this. Manipulations with plaster are similar to those described. The stem of the mushroom is wrapped in film to make it easier to pull out. It is installed at the moment the mixture begins to set. The product will be ready after final drying. For decoration, various beads and flowers are glued on.

The fungus is primed. Use glue that is diluted in water. You can use special construction soil. It hardens in 2 hours. Next, you can decorate the product, and after the paint has dried, apply varnish.

Fairytale plaster caterpillar

Garden sculptures can be magical. A caterpillar in a reduced form will perfectly complement the gypsum mushroom. You can make such figures with your own hands separately.

For the process of creating a caterpillar, use the following:

gypsum;
waterproof glue;
acrylic paints;
brush;
priming.

The plaster must be diluted to such a consistency that it resembles a liquid cream. First you need to fashion 10 circles of different sizes, which you slightly flatten with your fingers. Separately make 2 balls of the desired size (if the caterpillar is funny, you can make them larger). These will be her eyes. The constituent elements of the fairy-tale heroine must dry well.

Then the parts are glued together with glue. The sequence can be any, it is not necessary to follow a geometric sequence from large ball to small one. Having made the body, eyes are glued onto the large head.

The track needs to be completely primed. It should dry within 1.5-2 hours. It is best to decorate the product acrylic paints bright colors and again wait for them to dry completely. The finished caterpillar is carefully varnished. You can cover it with several layers of varnish. Between manipulations you need to wait a little so that the first layer dries. The completed figurine should be placed on the fungus, next to it, or on its own among flowerpots.

Gypsum as the best material for crafts

The use of gypsum is quite common when decorating a cement garden. The main requirement for gypsum products is their resistance and strength to environmental factors, and, in particular, to rain, snow, and hail. In most cases, it is not necessary to maintain absolute accuracy in the depiction of any figure. Garden figures small sizes sculpted without creating a base.

If you want to make an impressive sculpture that will have upper and lower limbs or other parts of the body, clothing, a metal frame should be created. For this purpose, metal rods are cut into pieces required length. They are then welded to create a single frame. It should visually recreate the skeleton of the potential statue.

During the manipulations of making the figure, one cannot forget about the details - the protrusions at the foot. Thanks to them, the sculpture can be firmly fixed to the prepared foundation. A plaster figurine can easily lift your spirits if done in a humorous style. If you don’t want to create a pompous product, you can make a funny animal, for example, a cat, a dog, a dolphin.

To obtain a gypsum product, glue is added to the diluted material. Its amount is determined by the volume of the figure - take 1%. To make the finished product as durable and beautiful as possible, plaster is applied gradually and in layers. After applying a layer, you need to let it dry, then the next one.

Plaster products can carry meaning and act as amulets. You can create guardians of garden flowers and other plants; for this it is worth making gnomes. With their brightness, good-natured look and cheerful appearance, they will cheer up guests even on cloudy days.

There is no need to make too many sculptures for your garden with your own hands. Everything should look natural, it is important not to overdo it, since nature itself is fabulous. It just needs to be improved a little. After making a simple plaster figure, you can get inspired and create something else. Several unique pieces will complement each other, especially if they harmonize stylistically.

Landscape designers love to decorate suburban areas with products made of stone, concrete and cement. Although these words sound very loud and intimidating, in fact, crafts made from cement or pebbles look very cute. A big plus is that making crafts from cement for the garden with your own hands is very simple. Therefore, if you want to add some zest to your garden, then take a closer look at these. Anyone can decorate a garden with such homemade sculptures, flowerpots and candlesticks! See what you can do with concrete.

15 GREAT GARDEN DECORATING IDEAS

Make a leaf-shaped birdbath. For this you will need a large concrete solution. Just lay a layer of cement on top of the sheet and wait until it dries completely.

Original garden flowerpots for growing annuals are made from boots. Just pour a cement solution into old rubber boots, place a mayonnaise bucket on top (so that there is a recess) and dry. Everyone will be surprised by cute boots. You can color them later.

Stylish lamps that are not afraid of rain can be hung on the terrace or in the gazebo. The principle of making crafts from cement with your own hands is the same - fill the mold with cement solution, insert a straw for juice where the wire will pass and dry it.

The heart-shaped mini flower beds are absolutely adorable!

Now garden flowerpots made of cement can be made to suit every taste.

Wow, decorative legs look really fun!

If you fill such a concrete structure with ice, you will get an excellent outdoor refrigerator. A necessary thing for!

You can make flowerpots for flowers of any size and shape. Such cement crafts for the garden will always find a place.

To get such graceful hands, you need to fill the glove with concrete, wait until it hardens completely, and then remove it from the product. How beautiful it is! This is a decorative fence for flowers.

Concrete cups can last for more than one year.

Cement country candlesticks will create a romantic atmosphere on a summer evening.

Now you are not afraid that the vase will break.

And these DIY cement dacha crafts are perfect for landscaping.

The small pond was made with a lot of love.

Rest assured, these DIY garden cement projects will transform it. Try to do something interesting.

How to properly mix cement for country crafts.

To ensure that the mold of the craft is completely filled, there are no bubbles on the surface of the casting, the resulting product does not crack after drying, or burst in the event of exposure to fire, you need to mix the cement (or concrete) correctly.

For small projects, 30 kg or less, cement can be mixed by hand. If you are planning something on a larger scale, you will need a concrete mixer.

Mixing cement can be mixed in a bucket, trough, or on plastic sheet or tarpaulin. Whenever you need to handle concrete, be sure to wear thick gloves. Concrete is caustic and thin gloves will tear too quickly. This will help as you work with a putty knife or small shovel to scrape down the sides and bottom of the bucket.

To mix cement mortar with your own hands you will need:

Thick rubber gloves
Respirator
5 - 8 gallon bucket/trough/similar
Master OK
Ladle/Clean Water.
Mechanical mixer (optional)
Using a 1/2″ corded or cordless drill with a paddle mixer is one way to mix dry material. Once water is added, the concrete will be more difficult to mix unless you have a very powerful drill.

The process of preparing the solution

1. Weigh all dry materials and add them to the bucket ( concrete mixture, pigment, fiber, or any all-in-one composition).

2. Stir the dry material together until it becomes a uniform color. Always wear a face mask when mixing dry concrete.

3. Break up any clumps of concrete or throw them away if they do not disintegrate.

5. Add water to dry material and mix. Scrape down the sides and bottom of the container where you mix, making sure you don't leave behind any dry material.

6. Add the remaining water gradually, as needed, until the mixture reaches a workable consistency. If the mixture is too hard, you may need to add a little water. There should be no dry pockets at this point. Mix thoroughly before pouring.

7. Clean the container after mixing with water. Do not pour it down the drain as it contains active cement components and it will clog the drain.

The need for fresh air and silence is common to most residents of megacities. People tend to go to their dachas, many move to live outside the city. Of course, one of the main issues is hygiene. But far...

There is a whole problem of how to keep a child occupied at the dacha or in the village when all the games have been played out and they are tired of messing around in the garden beds. So that the child does not hang out in front of the TV in the summer, but plays in the fresh air...

I admire gardeners who not only grow vegetables and flowers on their suburban area, but also create a magnificent stunning design of flower beds. Come up with an idea, find the time and create...

Having country cottage area, you always want to arrange it, and in some special way. However, garden decorative elements They are not cheap, and they are not durable.

People with developed imagination can do original crafts for a garden made of cement, which is not only highly resistant to various types of influence (frost, hail, sun, water), but also accessible (you can buy it at any hardware store for a reasonable price).

Can be used for decoration and design addition flower pots, flowerpots, figurines of fairy-tale characters or objects of the plant world, made with your own hands from cement. This material cannot be called capricious, and most people have a lot or little experience working with it. Still there are a few important rules that must be observed in order for crafts made from cement mortar to be of high quality and durable.

The technology for preparing the mixture is as follows:. The main components are prepared: cement, construction sand, water and tile adhesive (for better ductility and reducing the risk of microcracks). For 1 part of cement, take 2 parts of sand (for greater strength, you can take 1 part) and 1 part of glue. Lastly, add water in small portions to the consistency of thick sour cream. It is convenient to work with such a mixture: it does not flow and at the same time is quite plastic.

All cement products require prolonged drying. Hardening can last up to 7 days. To prevent the surface from cracking, the finished creation is covered with polyethylene. To give the product a beautiful and correct form, the base is placed on a hill of sand or buried in it (depending on the idea), but not on a flat surface.

After complete hardening, the figure must be coated with a primer and only after that can paint or varnish be applied. If the craft has roughness and other irregularities, it is modified before priming sandpaper and a file.

In addition to cement mortar, concrete is sometimes used, which is characterized by the presence of large fractions (pebbles or crushed stone) and increased strength. Crafts made from concrete for a summer residence can be represented by large monolithic boulders, and this material is also convenient to use to create the basis for various compositions (a platform for a fountain, a pedestal for a sculpture, a terrace for flower pots And so on).

Another material similar in its application is gypsum. It is not as strong as cement, but more plastic and decorative. It can be used to create hollow shapes. For garden creativity, molding (sculptural), acrylic and architectural types are used. When working with this material, you need to take into account its rapid hardening. It is often recommended to add it to cement mortar when creating sculptures.

Having no experience using cement in decorative purposes, it is better to start with something simple that does not require modeling skills and obtaining the desired consistency. The first exhibits in your garden can be cute mushrooms, colorful balls or original flower pots.

To make a mushroom you will need an old rubber ball (the size of the cap will depend on its size), a plastic bottle (it will become the basis for the stem, its size should be proportional to the cap), a metal rod to attach the cap to the stem. The ball is cut into two halves, one of which is placed in a bucket of sand and pressed evenly. Next, cement mortar is poured into the resulting form and leveled.

U plastic bottle cut off the bottom and neck and insert it into the filled form in the center, immersing it by 1 - 2 cm. Then, using a long iron rod, connect the future stem and cap of the mushroom and fill the cavity inside the bottle with the solution. The product should harden for several days, after which you need to remove the piece of the ball and the plastic cylinder.

After a few more days, the product can be coated with paint and decorated. different elements. Mushrooms of different sizes look impressive on the plot in the form of a small clearing. It is also worth noting that your imagination may tell you to use other containers (bowls, jars) and methods for making garden mushrooms.

It’s enough to just make an openwork ball that seems so light and airy. For the base, use a balloon (the size of the future shapes depends on how much you inflate the balloon). Next, any rope is placed in the prepared solution and then the ball is wrapped around it.

Do not wrap the base too tightly; you need to leave enough holes for further removal of pieces of the burst ball. When the product is dry, you can begin decorative coating.

If you cover the balloons with cement mortar with a small amount of gypsum added for faster hardening, you can get original garden lanterns or flower pots.

Using this technique you can also make vases for dried flowers. In this case, not only the outer side, but also the inner side is subjected to decorative painting.

If you pour the solution into a small hole in rubber balls, you can get monolithic balls of different sizes. Painted in different bright colors and randomly scattered around the garden, they will become a laconic and stylish decoration.

Using plastic containers, you can make a flower pot for Crassula and Crassula Ovata cacti. The container is wrapped plastic bag, and a bag of clay or sand is placed inside so that the container holds its shape. Next, it is covered with cement mortar. After complete drying, all auxiliary materials are removed, drainage holes are made in the bottom using a drill, the product is primed and painted.

It's very easy to make a flowerpot using a plastic bucket or vase and another suitable container.

One container is inserted into another, and the solution is poured into the space between them. The result is a high-quality product that can be further decorated by showing your imagination to the fullest.

Flowers planted in flowerpots made from crossed palms look attractive. To create such a masterpiece, use ordinary rubber gloves, which are evenly filled with the solution. For rigidity, you need to insert a thick wire rod into each finger. To ensure a high-quality product, air bubbles must not be allowed to form.

When the gloves are filled, they are given the desired shape and fixed. After a few days, the rubber is cut and removed. If you need to connect two palms, then use the same solution. At the final stage, the surface is polished with sandpaper, primed and painted.

Complex figures with a frame

It's more fun to decorate your Vacation home sculptures of animals and mythical characters. Such creations involve the preliminary production of a durable frame and layer-by-layer application of cement mortar.

Interesting flowerpots can be made using buckets from construction mixtures. At the first stage, a container of suitable size is wrapped with a plaster mesh and covered with a thick layer of cement. At the second stage, until complete hardening, decorative adjustments are made, making an imitation of an old stump with natural wrinkles on the bark.

A monolithic figure of a hippopotamus would look appropriate near artificial reservoirs. The place for it must be determined immediately and carefully aligned, since in the future the figure will be stationary.

Two elongated plastic basins, which must be fastened with wire, are suitable as a frame. Another option is also possible: a thick cement solution is covered on top of the heap broken bricks or crushed stones.

The figure itself does not contain complex elements and easy to perform. After hardening, the product is treated with fixing impregnation and dry pigment for concrete, rubbing the powder with a hard sponge.

More complex sculptures are made in several stages: 1) making a frame from wire and foam plastic or containers; 2) covering the workpiece with a plaster mesh; 3) applying the mixture in several layers; 4) formation small parts(facial features, special texture, folds of clothing, etc.); 5) priming and painting the finished work.

Flowerpots in the shape of swans will become an elegant decoration of the garden. The body frame is an old plastic basin, the neck is woven wire. The head, wings and imitation plumage will have to be made from cement mixture, demonstrating the skills of a sculptor.

Monolithic figures have a significant weight, so as an alternative there is a way to create lightweight large objects. You can decorate your garden with boulders of different sizes.

To make them, any unnecessary and light material (trimmings) is tied into a tight lump with wire polyurethane foam, plastic bottles, foam).

The resulting base is wrapped in a plaster mesh and covered with thick cement mortar. The more irregularities and protrusions there are, the more natural the “stone” will look.

Small garden figurines made from a mixture of cement with the addition of gypsum or Portland cement.

Here you can use the manufacturing methods described above, as well as any basics: old toys, items of clothing, household utensils.

Step-by-step manufacturing instructions: 3 master classes

To take a closer look at the nuances of the creativity presented in the article, let’s look at best master classes with a step-by-step explanation of the work being carried out.

1. Spectacular flowerpots made of cement and fabric

To make flowerpots for the garden from cement and fabric, use either pure cement or Portland cement. In this case, the mixture with water should be quite liquid. You will also need a bucket or other container for the frame, a piece of polyethylene and a piece of fabric.

The material must be dense enough and absorb liquids well, i.e. synthetics will not work here. It is better to use cotton fabric.

Cutting off a piece the right size. If you need smooth edges, then round them;
We wet the material generously in the solution;
We attach polyethylene to the prepared bucket;
Lay the fabric soaked in the solution on top and smooth it out;
After 2 days, the cement will set and the bucket can be removed;
The product is lightly moistened with water and left to dry completely for another 5 days.

Even large-sized plants can be planted in a ready-made flowerpot.

Experiment with the shape and coloring of flowerpots and create your own unique compositions.

2. Funny cat for the garden

First, we prepare a frame from a cut plastic bottle and wooden slats which are fastened with wire.

The solution is prepared from cement and sand in a 1:1 ratio; additionally (directly into the hand) gypsum is added during the work. By gradually applying the solution, all the details of the sculpture are created.

The finished figure is polished with a damp hand and left to dry for 4 days. The final touch is painting with water-based emulsion or enamel.

3. Large leaf drinker for birds and pets

No less successful and universal decoration the garden will have a sheet of cement. A plastic film is placed on a mound of sand, and then a large sheet (the mound will allow you to get a shape with a depression, rather than a flat one). If there are small holes in the sheet, they should be covered with small leaves so that the cement mortar does not leak.

Cover the workpiece with film for several days until it dries. Then the sheet is removed, primed and painted.

If desired, you can make a fabulous fountain from several similar blanks.

Cement is not only unique construction material for the construction of buildings and structures. Cement is also an excellent substance for making all kinds of household items: flowerpots, tables, stools, garden paths, sculptures, etc.

What can you make from cement on your own?

Considering the low cost and excellent plasticity of cement-based mortar, options for crafts from of this material limited only by the imagination of the master. Moreover, all crafts are not “dust collector trinkets”, but have one hundred percent practical use. Below are a number of options that, without a doubt, will certainly interest everyone. home handyman"with hands and head."

Cement garden path

The following tools and materials will be required:

Special forms (can be purchased at any hardware store);
Cement mortar prepared according to the following recipe: 3 parts sand, 3 parts gravel, 2 parts M400 cement, water - approximately 0.5 of the amount of cement;
Curb stones;
Polyethylene film;
Reinforcing mesh. A steel mesh cut to shape for plastering is suitable;
Color for concrete (if necessary, get a colored track);
Equipment for preparation and leveling concrete mortar: container, shovels, buckets, trowel, spatula, building level.
Materials for marking the path: twine and metal or wooden pegs.

The main stages of pouring a garden path:

Marking and digging trenches;
Installing curbs and adding sand or gravel to the cushion;
Setting forms by level. The molds are pre-lubricated with machine oil or a special release solution;
Preparation of cement mortar. If necessary, a concrete color is added to the solution (proportions according to the manufacturer's instructions);
Filling the mold up to half, laying the reinforcing mesh, final filling, compacting and leveling the surface;
Cover the filled molds with plastic wrap for 72 hours. In hot weather, the surface of the path must be regularly moistened with water by spraying;
Dismantling the molds, filling the seams with sand.

From cement, or rather their cement mortar, you can make a designer tabletop, a stool, and even a sconce lamp.

Designer cement countertop

The solution for pouring the product is prepared according to the previous recipe. Reinforcement is also according to the previous recipe. The dimensions of the craft in the plan are taken either according to the existing table frame, or first the table top is made, and then, according to its dimensions, the frame with legs is made.

You will also need to make a mold for filling. As the mold material, you can use moisture-resistant plywood for the bottom of the mold and wooden slats 40x40 or 50x50 for edging and ensuring the thickness of the product: 40 or 50 mm, respectively. Let's consider the main stages of pouring:

Lubricating the inner surface of the mold with a release agent and setting it level on bricks or a flat surface;
Preparation of the solution;
Fill to the middle of the border;
Laying reinforcing mesh;
Final pouring, vibrating, leveling and covering with plastic wrap for 72 hours;
Carefully disassemble the mold, clean it, chamfer it, place it in a cool, shaded place until it dries completely.

Designer cement stool

You will need a conical shape. A round plastic bucket, which is sold in, will do. water-based paint, glue, etc. In addition, you need to select three legs. A wooden circle with a diameter of 35-40 mm is suitable.

The length of the leg is taken with a margin for finishing trimming: 450 mm (height of the stool), 0.5 times the thickness of the concrete seat - 50 mm, tolerance for finishing trimming - 25-30 mm. Total 525-530 mm. The stages of manufacturing a designer stool are as follows:

Preparation of the mold - lubrication with a release agent;
Preparation of concrete solution. Similar to previous options;
Filling the seat with a thickness of 100 mm;
Introduce the legs into the uncured solution to a depth of 50 mm, with an inclination of several degrees from the center in different directions;
Aging for 72 hours;
Stool recess;
Trimming legs to size. Chamfering;
Seat finishing – sanding and chamfering.

Designer sconce lamp made of cement

The following materials will be required:

The cement mortar is similar to the previous options;
Lamp holder, lamp, electrical plug, electric switch and electrical cord;
Plastic bottle with a capacity of 2.5 and 1.5 liters;
Emery cloth;
White paint on concrete;
2 self-tapping screws for wood or metal, 50-60 mm long;
Steel tube 120 mm long, with 3/8" thread on both ends and 4 3/8" nuts to it;
Scissors, drill with a diameter of 10-10.5 mm, hand or electric drill, spanners, tool for preparing solution, screwdriver.

Where to start to make a lamp:

Use a knife or scissors to cut off the bottom of the bottles;
We drill holes with a diameter of 10 or 10.5 mm in the necks of the bottles;
We attach a threaded tube to the lids so that there is a distance of approximately 80 mm between the lids, and the ends of the tube protrude from the top of the 2.5 liter bottle cap and the bottom of the 1.5 liter bottle cap by approximately 20 mm;
We screw onto bottle caps in the format - “1.5 liter bottle inside a 2.5 liter bottle;
Stepping back 2.5-3 centimeters from the edge of the bottom of the large bottle, we connect both containers with self-tapping screws in the “one opposite the other” format;
Mix the solution and fill the space between the containers;
Leave for 72 hours. We heat it with a hairdryer, cut and remove the bottles, treat the “shade” with sandpaper, paint inner surface lampshade with white paint.

Next you should collect electrical diagram, consisting of: a plug, an electrical cord, a switch and a socket, make a simple cantilever bracket from wooden slats, paint it with white paint, hang a lamp on it and fix the resulting exclusive structure on the wall.

In addition, you can make it from cement, as well. Use your imagination and you will succeed.