On a stand in a plumbing store or in a photograph in an online store, an acrylic bathtub, as a rule, appears assembled. Meanwhile, products produced by Aquanet arrive in the regions in a disassembled state, and chain stores often supply them in the form of a kind of “Assemble it yourself” construction kit. As a result, the question arises of how to install an acrylic bathtub .
Task one. How to assemble a frame for an acrylic bathtub
Acrylic bathtubs ordered from the Aquanet online store are delivered to the customer with an assembled frame. All that remains is to install it and, if necessary, fix it against the wall using fastening materials. Insulate the junction of the bathtub with the wall using a special self-adhesive plinth or plastic corner, which is attached to sanitary silicone. If the faucet is already installed, you can immediately use the bathroom. To help those who received the bath disassembled, that is, the bowl is separate from the frame, instructions are given. And here you already need to use your abilities as a home craftsman.
To make the task of assembling the frame easier for yourself, the most win-win way to quickly and efficiently install an acrylic bathtub is to contact the service department. At Aquanet, this also allows us to automatically double the equipment warranty. By the way, service specialists can also help if the bathtub arrived at its destination with the frame already assembled. In this case, the craftsmen will level the product, connect the drain and overflow, install the front panel if required, and treat the joints with sealant. That is, they will prepare a turnkey bathtub, taking into account all the nuances, since they know the specifics of each model very well. In this case, operation of the acrylic bathtub is possible immediately after the service technicians leave.
If you decide to assemble the frame yourself, you should keep in mind that for different models Acrylic bathtub frames are individual. Moreover, the frame designs are different not only for asymmetrical or corner products With individual form, but also for rectangular ones. Therefore, for the installation of each acrylic bathtub model, a manual has been developed that will help you understand the intricacies of the assembly. It is included with every product purchased from Aquanet.
However, there is a general procedure that is unified for all models. For example, let's take a step-by-step look at how to assemble the frame of a corner acrylic bathtub .
Step 1. Turn the bathtub upside down and place it on a flat surface that will not damage or scratch the bathtub. In the corners of the bathtub, measure a distance of 40 mm from each side to determine the position of the center of the vertical stand.
Step 2. Screw the racks into the MDF inserts located in the corners of the bathtub, using two 3.5*16 self-tapping screws in each rack.
Step 3. Place the frame on the bottom of the bath so that it does not protrude beyond the dimensions of the bath, and connect it with three vertical posts bolt and nut M10 through holes with a diameter of 13 mm.
Step 4. Screw the frame with 3.5x40 self-tapping screws to the mortgage on the bottom of the bathtub in five places.
Step 5. Screw the corners into the MDF inserts, which are located around the perimeter on the front side, to support the front panel.
Step 6. Insert supports (flags) for fastening the front panel into holes with a diameter of 13 mm on the posts and secure with M10 locknuts.
Step 7 To open parts profile pipe insert plastic plugs 25x25.
Step 8 Install the legs into the holes on the frame with a diameter of 13 mm and secure them with nuts. Adjust the legs using a level. The height of the leg should be 640 mm.
Step 9 Install the front panel between the corners and the side of the bathtub so that there is an angle of 90 degrees between the panel and the bathtub. At the same distance from the side of the bath, you need to drill holes in the panel with a diameter of 8 mm opposite the flags.
Step 10 Screw the panel with 3.5x40 self-tapping screws, then screw in the decorative part of the plug.
Attention! According to SNiP (Building Norms and Rules), the height of an acrylic bathtub from the floor to the top of the bathtub should be 60 centimeters. If the bathtub is used by children, disabled people and the elderly, then this figure is less - 50 cm.
Task two. How to install an acrylic clawfoot bathtub
Budget bathtub models, as a rule, are installed on so-called eco-legs, and not on a frame. They come with the bathtub. You need to install them yourself. Each model comes with instructions. But let's take a look at all the nuances of installing a bathtub on legs:
Step 1. Screw M12 nuts (lock nuts) onto M12 studs L = 200 mm on both sides at a distance of 3-4 cm. Then screw on the M12 legs made of black plastic on one side and secure them with locknuts.
Step 2. Place the bathtub upside down on a clean, flat surface. Measure the protruding part of the bathtub and mark the middle. 
Step 3. Place the first load-bearing profile of the frame on the bottom of the bathtub, 50 mm away from the edge of the embed. Connect the middle of the supporting profile with the middle of the mortgage and screw it in four places with 4.0*20 self-tapping screws, as in rice. 1.
Step 4. Measure 10 mm from the drain side and install a second supporting profile
Connect the middle of the profile with the middle of the mortgage and screw it in four places with 4.0*20 self-tapping screws.
Step 5. Install the legs into the 13 mm diameter holes of the supporting profile. On the side where the front panel will be installed, install a fastening flag with an M12 washer and an M12 nut. On the other side, install the legs and secure with an M12 nut, as on rice. 2.
Step 6. Adjust the height of the legs. The recommended height of the leg is 160 mm from the frame.
Attention! When installing a bathtub, the front panel, if it is already installed, must be removed. It must be attached to the product last.
Task three. How to fix an acrylic bathtub
Perhaps the simplest of tasks. If there is a reliable frame for installing a bathtub, it is usually not attached to the wall. But for inner peace, and especially if you place the bathtub on eco-legs, it is better to provide reliable fastening. To do this, you need to perform a number of actions.
Step 1. Measure the height from the floor to the edge of the bathtub side and mark the places where the corners are attached (see Fig. rice. 3).
Step 2. Using a drill with a diameter of 6 mm, make holes in the marked places and install dowels where the fastening corners should be screwed.
Attention! The bathtub should not hang on the mounting angles. To prevent this, you can adjust the height of the bathtub using the legs.
Task four. How to install the front panel
If you are not covering the bathtub with plasterboard and do not plan to mount it on a podium, then it is best to cover the front part with a front panel.
Step 1. To attach the front panel to the top (if provided), screw the mounting corners (4 pieces) with 4*16 self-tapping screws into the inserts located around the perimeter on the front side of the bathtub. When installing the mounting bracket, provide a distance to the side of the bath that is equal to the thickness of the front panel.
Step 2. Screw an M10 nut onto the front panel fastening flags (M10 stud with a welded perforated plate). Insert into the holes in the corners of the frame and fix it so that when installing the panel there is a 90 degree angle between the panel and the side of the bath.
Step 3. Install the front panel between the mounting brackets and the front of the bathtub edge. Align the panel. At the level of the flags and at the same distance from the edge of the front panel, drill two 8 mm holes. Screw the front panel with 4*16 self-tapping screws with the threaded part of the plug to the fastening flags and screw on the decorative part of the plug.
Attention! If you ordered a model with hydromassage equipment, then you need to take care to make grounding an acrylic bathtub.
The advantage of acrylic bathtubs is their lightness, but this point is also their disadvantage, since a rather fragile and thin structure may not withstand and burst upon impact or be damaged by the fall of a heavy object.
Agree, I wouldn’t want to spoil the new plumbing during installation. In general, installing an acrylic bathtub yourself is not a difficult task. The main thing is to understand the principle of operation and adhere to the technology.
Below are various ways installation of the bathtub, the procedure for connecting the siphon and sewerage supply is described. All instructions are accompanied by visual photographs and video materials.
Bathtubs made of acrylic are very beautiful, they have original design and various color solutions. At the same time they have their own weak sides and vulnerabilities.
Therefore, it would be a good idea to find out what problems you may encounter during installation and subsequent operation, and how to prevent them.
Colored acrylic bathtub unusual shape will become a bright and original element that can decorate the interior of any bathroom
Among the advantages are:
- Plastic. Acrylic lends itself well to molding and subsequent processing. This property of the material determines the presence of a huge variety of shapes of acrylic bowls.
- Lightness. The acrylic bathtub is light in weight (15-25 kg), so its installation can be easily handled by one adult man.
- Priority heating technology. Acrylic itself is warm material. In addition, it has low thermal conductivity; bathtubs made of acrylic can retain heat for a long time; the water in them cools much more slowly than in cast iron structures.
- Maintainability. Plumbing fixtures and acrylic products in general lend themselves well to repair and restoration. If the damage is significant, then you can restore the bathtub using an acrylic liner, which is made for a specific design and then simply inserted into the old container.
As for the disadvantages, they are also present. We must not forget about the disadvantages. Following the recommendations below will help you avoid possible problems and extend the life of the acrylic bathtub.
To the disadvantages acrylic sanitary ware include:
- Sensitivity to high tº. Acrylic doesn't hold up very well high temperature. When heated above 60 degrees, it may become deformed, so you should not pour too hot water into the bath.
- Fragility. If you accidentally drop a heavy metal object, a step like uneven surface, its bottom can be pierced through.
- Vulnerability. Acrylic bathtubs are capricious - they cannot be rubbed with hard brushes or washed with powders containing abrasives, since the enamel is very sensitive and can be easily scratched by exposure to hard particles.
And it should also be noted, if not a disadvantage, then the inconvenience faced by those who first plunged into an acrylic bathtub. Due to the thinness of the material, the bottom may bend slightly under the weight of a person. However, you get used to this feature of an acrylic bathtub quite quickly.
Image gallery
Conclusions and useful video on the topic
Assembly of the frame and installation of a bathtub with a plastic screen is described in the following video:
Video instructions on how to properly assemble a factory metal frame for an acrylic bathtub:
Acrylic bathtubs angular, round or asymmetrical shapes are installed only on a factory metal frame. Manufacturers are making detailed instructions, according to which any man can cope with this work on his own. However, it is better to entrust the installation of a hot tub to specialists, since it requires the connection of complex electrical equipment.
Do you have anything to add or have questions about installing a bathtub? Share personal experience plumbing installation and please leave comments on the publication.
Instructions for acrylic bathtubs from Bas
Thank you for purchasing this bathtub. trademark"BAS".
- Preface
Baths "BAS" are modern technologies and original lines that provide comfort during water procedures.
This manual describes the bathtubs' functions, installation requirements, maintenance and operating methods.
Attention: In order for the bath to benefit you and work for a long time and reliably, a number of conditions must be met:
1) Consult your doctor to what extent taking a bath is beneficial for you.
2) Consider installing filters for water purification.
3) Do not turn on the hydromassage without filling the bath with water!
4) It is forbidden to seal the seams between the wall and the bathtub with rigid building materials (ceramic tile, curbs, mortar, etc.)
- Technical description
Standard equipment for a hydromassage bath:
1. Acrylic bathtub - 1 pc.
2. Metal frame - 1 pc.
3. Legs - 4-8 pcs. (depending on model)
4. Panel clamp - 2-4 pcs.
5. Self-tapping screws for fastening the acrylic panel - 5-12 pcs.
6. Additional equipment: acrylic panel (screen), drain-overflow device, back massage, aeromassage, etc. (at the buyer’s request)
Transporting bathtubs When transporting and installing a bathtub, care must be taken not to damage the piping systems and electrical equipment. DO NOT: carry the bathtub by the piping and electrical wiring. It is necessary to avoid mechanical damage to the bath body and screen, and also to exclude the effect of chemically active reagents on the surface of the product.
Instructions for preparing a site for installing bathtubs:
1. A plumber performing work on the removal of hot and cold pipes cold water, must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may rest against the stiffeners, units and fittings of the bathtub. This means that the bathtub cannot be installed close to the walls.
2. The bathroom drain pipe should not rise above the floor by more than 10 cm. If this cannot be ensured, then a podium must be made.
3. The legs serve to level the bathtub, so additional supports must be installed under the supporting structure of the bathtub.
4. Electrical wiring for the bathtub equipment must be made with a double-insulated cable with a cross-section of 2.5 mm2.
System protection should be based on differential (multiple) shutdown (1fn=30 mA). The power cable must comply with EEC regulations and standards
- Electrical system
The installation of the electrical system must be carried out by a professional electrician with an electrical safety clearance group of at least group 3. The power supply wiring for the lighting and hydro-air massage system of the bathtub must have a “Residual Disconnection Device” (RCD) with a rating of 30 mA.
- Attention:
Connect the electrical cable in the following order: blue wire— “zero” brown wire — “phase” yellow-green wire — “grounding” The power supply for the lighting and hydro-air massage system of the bathtub must be connected only through a separate RCD with a rating of 30 mA. The RCD must be located outside the bathroom. It is strictly prohibited to connect the power supply to the lighting or the hydro-air massage system of the bathtub through a plug and socket.
Using the lighting system without water in the bath is strictly prohibited.
- Name V Hz kW
- Hydromassage 220/240 50 0.9-1.5
- Air massage 220/240 50 0.7-0.9
Power is indicated depending on the bath model.
- Equipment for hydro and aeromassage includes:
1. hydraulic pump
2. compressor for air massage
3. function activation buttons and hydromassage power control
4. hydromassage jets (back side)
5. piping system
- Optional equipment
aeromassage (the jets are at the bottom of the bath)
hand shower, cascade, mixer
backlight
back massage
headrest
pen
- Bathtub Installation Guide.
1. Before installing the screen, first mark the location of the centers of the screen mounting plates on the front side of the bath with a pencil or felt-tip pen.
2-5. Next, you need to screw 4 M 12 nuts onto the mounting legs, use two M 12 nuts to screw the mounting legs to the bathtub frame, and use the remaining two M 12 nuts and two M 12 washers to secure the screen mounting corner on the mounting leg so that it reaches the edge of the screen . Attach the screen to the bath and use a drill dia. Make 3.5 mm holes in the corners of the screen mounting (it is recommended to perform this operation after first removing the screen).
6-7. Mark on the top of the screen the points with the centers of the screen mounting plates already marked on the front side of the bathtub, placing them at a distance of 1.5-2 cm from the lower edge of the front side of the bathtub. In the marked areas of the screen, use a drill with a diameter of 3.5 mm to drill holes for self-tapping screws. Next, use the same drill to make holes in the mounting plates of the screen (it is recommended to perform this operation after first removing the screen).
8. Using the legs, adjust the bathtub to the height of the acrylic panel, taking into account the zero level of the upper plane of the bathtub.
9. Install the drain and overflow device on the bathtub, screw on the siphon (not included in the kit) and connect to drain pipe bathroom
10-11. Having aligned the screen with the bathtub embedded parts, it is necessary to screw self-tapping screws into the holes, and then put plugs on them.
12. After installing the bathtub, remove the protective film.
13. Install the bathtub wall bracket. A wall fixing is offered to enhance the rigidity of the bathtub.
- ATTENTION:
It is prohibited to seal the seams between the wall and the bathroom with hard building materials (ceramic tiles, curbs, mortar, etc.) If the above is not observed, warranty repairs will not be carried out
Instructions for using hydro-, aero-massage, back massage, water illumination (mechanical activation of functions).
- Buttons for turning on hydro-, aero-massage, water lighting. (on and off - by pressing your finger inward)
- Switch for hydromassage and back massage. (simultaneous operation of functions is possible)
- Power regulator for hydromassage and back massage. (turn the knob clockwise)
Electronic (touch) control of hydro-, aero-massage, chromotherapy functions. (1, 2 — air massage power control; 3 — on/off air massage function; 4 — on/off hydromassage function; 5 — on/off chromotherapy function)
- The hydromassage and chromotherapy functions are automatically turned off if there is no water in the bathroom. The air massage is turned off manually after the jets have been purged.
Bathroom care
When cleaning the bathtub, use a liquid cleaner that is harmless to acrylic and plastic surfaces(see cleaning product instructions). The manufacturer offers you a specialized cleaning agent “TIM-PROFI”, adapted to our products. Clean stains with a napkin made of soft fabric.
Scratches or burn marks from cigarettes that appear on the surface can be removed with light scrubbing. sandpaper(No. 1000/2000) with water. You can restore the shine of the surface with a liquid polish.
- Cleaning hydraulic system baths
This type of cleaning is performed using hard water (more than 15 salt deposits per cubic meter water). It is recommended to clean the bathtub hydraulic system at least 2 times a year as follows:
1. Fill the bathtub hot water(40C).
2. Pour in liquid detergent at the rate of 2g per 1 liter of water and run the hydromassage for about 5 minutes.
3. After this, turn off the electric pump and drain the water from the bath.
4. Refill the bathtub cold water and turn on the hydromassage for 2 minutes.
5. Drain the water and wash the bathtub (see “Bathtub Care”).
The manufacturer offers you a specialized cleaning product for the hydraulic system, adapted to our products.
WARNING: Never use a metal brushes or tools, as well as solvents and detergents with abrasive additives. Also avoid contact of ammonia or chlorine with brass and chrome parts of the bathtub.
- How to use hot tubs
It is forbidden to turn on hot tub with closed hydromassage jets and the water level is 5-6 cm below the jet opening. Never use the bathroom after taking alcohol or taking medications. Hydromassage in medicinal purposes can be carried out only on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should only be performed in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel drowsy while taking a bath, turn off the hydromassage device for a while and cool the water.
For overweight people, hydromassage baths at water temperatures exceeding 38 C are contraindicated.
Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upward.
- The simplest malfunctions, their possible reasons and solutions.
| Occurring fault | Possible reason | Remedy |
| There is no voltage in the network. | Call a specialist (electrician). | |
| The hydraulic pump does not turn on. | The plastic tube connecting the button and the pump came off the hydromassage button. | Turn off the voltage. Attach layer. tube to the base of the button and turn the system back on. |
| Jet nozzles are closed. | Turn counterclockwise to open the nozzles. | |
| The hydraulic pump works, but no water flows from the jets. | The piping system is clogged. | See the "Bathroom Care" section. |
| Increased vibration in the operation of the hydraulic pump. | The engine mount is loose metal frame baths. | Turn off the voltage. Tighten the engine mounting bolts. |
The manufacturer reserves the right to make changes to the design and configuration of bathtubs.
In winter, the product is installed in a warm room after 6 hours from the moment the bath is delivered to the client
If a drain or overflow is installed in a manner not provided by the manufacturer, the bath will be void of warranty.
Active substances must not come into contact with the surface of the product. chemical substances that can damage the acrylic layer.
High (above 80C) thermal effects on the surface of the product are prohibited.
Installation (installation) of the bathtub (shower curtain) and the equipment included in the kit is carried out by the buyer with the involvement of specialists licensed to carry out this type of work. The installation warranty is provided by the installer with a note in the warranty card.
Installation of products must allow easy access to components and assemblies attachments, as well as to connecting hoses supply of water and air.
Dear buyer! The manufacturer sets the warranty period for bathtubs to 10 years. This warranty period covers all equipment, except for: drainage and overflow devices, hydromassage, air massage and any other additional equipment (see clause 7, page 1 of this manual), for which the warranty period is 2 years.
- Warranty service is not provided in the following cases:
– non-compliance with installation rules and operating conditions;
– loss of a receipt or warranty card;
– negligent storage or transportation by the owner, trade or transport organization;
– attempts at unqualified repairs;
– mechanical damage, traces of exposure to chemical and abrasive substances during improper care for the product;
– making corrections to the text of the warranty card;
– the RCD (residual current device) is not installed, if there is electrical equipment on the bathtub;
– use of the product for business activities.
The company does not assume responsibility for damage caused during transportation and delivery.
Warranty service does not include reimbursement of installation and disassembly costs.
- Video instructions for assembling the frame of an acrylic bathtub Bas
BAS brand products are fully certified and labeled. Acrylic and hydromassage bathtubs and shower cabins BAS have proven themselves excellent in Russia and the CIS countries. The reason for this is the impeccable quality and reasonable price. Today this is the best offer in terms of price/quality ratio.
BAS brand products are fully certified and labeled. Acrylic and hydromassage shower cabins BAS have proven themselves excellent in Russia and the CIS countries. The reason for this is the impeccable quality and reasonable price. Today this is the best offer in terms of price/quality ratio.
All products are manufactured on Italian equipment from sheets of Sanitary Acrylic/ABS multilayer polymer material from the Austrian company "Senoplast" on Italian vacuum forming equipment. Bathtubs and shower cabins of the world famous brands “Jacuzzi”, “Teuco”, “Albatros”, “Villeroy&Boch” are made of the same material.
In Europe and other Western countries, BAS have long earned consumer trust. Cast iron and steel baths have become a thing of the past because they are inferior in many characteristics. Acrylic bathtubs are more resistant to mechanical damage, are much easier to clean and do not lose their color over the years. In addition, they are very pleasant to use and retain heat well while taking a bath.
Acrylic baths BAS They come in different colors, which helps you choose what best fits into the design of your bathroom.
If you want more than just a bath, BAS hot tubs are available. By purchasing a hot tub, you will have a personal medical office. Hydromassage relaxes, improves blood circulation, and even improves immunity. It is used for both medicinal and cosmetic purposes. The BAS hot tub is not only useful, but also brings a lot of pleasure.
So, you have decided to purchase an acrylic bathtub. Perfect solution! In this article we will give you the 5 most important advice that will help you do right choice so that your bath will give you only pleasure and benefit for many years to come.
When choosing an acrylic bathtub, everything depends only on your desires and financial capabilities. In order not to get lost in all the variety of bathtubs that currently exist, it is worth understanding a few key points that will make your further search easier.
Tip 1: Prices vary
Like any product, acrylic bathtubs vary in price. Now on Russian market presented a large number of manufacturers of acrylic bathtubs, offering from the cheapest to the most expensive models. The price of a bathtub is influenced by the quality, size of the bathtub, and its design. The lower price limit for an acrylic bathtub is now about 8 thousand rubles. The upper one has practically no limit.
Tip 2: Make your design dreams come true
One of the main advantages of acrylic bathtubs is the wide variety of designs. Your acrylic bathtub can be of almost any shape, from the classic rectangular to the unusual asymmetrical one. This variability allows the buyer to install a bathtub even in the smallest room, as well as to implement any design ideas. If you dream of a sophisticated and stylish acrylic bathtub, pay attention to the bathtub designs from Italian manufacturers.
When choosing an acrylic bathtub, decide what space in your bathroom it will occupy; the size of the bathtub depends on this. For small room An ergonomic bathtub measuring 120x70 is suitable, and for a more impressive space you can choose a more impressive size, for example 190x120.
Tip 3: Special attention quality
When choosing a bathtub, first of all check the availability of all certificates, and also find out what polymer the bathtub you like is made from. There are two types of polymers that are used to make acrylic bathtubs. 
The first - ABS/PMMA - is a combination of two types of polymers - acrylonetrile butadiene styrene and polymethyl methacrylate, combined by co-extrusion, that is, combining materials with different properties. The thickness of the acrylic layer in such baths is only 5-10%, everything else is ABS polymer, which has a number of disadvantages - relatively low density, tendency to absorb moisture, roughness and porosity of the structure. Such baths are usually cheaper, but be prepared for the rapid appearance of microcracks, chips, and loss of appearance. The service life of such baths is only 3 years.
The second type of material is 100% cast homogeneous acrylic, that is, polymethyl methacrylate. Bathtubs made from such a polymer have all the qualities necessary for a bathtub - wear resistance, high strength, good appearance, maintainability. The service life of bathtubs made of cast homogeneous acrylic can be 10 years.
How to distinguish a bathtub made of 100% cast homogeneous acrylic from an ABS/PMMA bathtub? Look at the cut edge of the bathtub. If the bathtub is made of homogeneous acrylic, there should be only two layers - acrylic and resin. ABS/PMMA bathtubs have three layers - a thin layer of acrylic, a large layer of ABS plastic and a third layer of reinforcement. So if the cut of the bathtub is more than 8 mm thick, and the seller tells you that the acrylic here is 6-8 mm thick, then most likely you can say that he is lying. There is 1 mm of acrylic as such, followed by a layer of plastic - ABS.
The quality characteristics of an acrylic bathtub that are worth paying attention to also include its rigidity and shape stability. These qualities are given to an acrylic bathtub by the reinforcement procedure that the bathtub undergoes during manufacture. The reinforcing layer consists of glass fiber and epoxy resin. And the reinforcement process, accordingly, is the application of such a layer to the bathtub. The more layers, the stronger the bathtub. The number of layers with which the bathtub was strengthened at the factory can be easily determined by carefully examining the edge of the side. The layers are clearly visible, like annual rings on wood. Therefore, the walls of the bathtub should not sag; this must be checked when choosing a bathtub.
Obviously, what better quality, the higher the price. A compromise allows you to find bathtubs from Polish manufacturers that offer a very reasonable price-quality ratio.
Tip 4: Tuning your bath
For an acrylic bathtub, you can purchase additional equipment. This includes mixers, hydromassage systems, decorative panels, end\front curtains, headrests, handles, mats, etc.
Of all the above, to necessary equipment, which will definitely need to be purchased along with the bathtub, is a faucet. And here is another advantage of an acrylic bathtub - the mixer can be placed on the side of the bathtub in any place where it is more convenient for you. You can even make several mixers. An acrylic bathtub allows you to realize all your ideas. 
Faucets, like all plumbing fixtures, vary in price and quality. When choosing, for example, Italian manufacturers, you can be sure that the money was not paid in vain. Take the cheaper one, made in China - it's up to you, but don't wait long term services.
Tip 5: Buy a bath without leaving home
Now there are many places where you can buy an acrylic bathtub: plumbing stores and showrooms, construction markets, specialized shopping centers. But all this requires a lot of time, effort and nerves. Recently, it has become possible to purchase acrylic bathtubs online. It is much more convenient and profitable. You can choose the option that suits your price and design, which will be delivered to you directly to the specified address.
OPERATION OF BAS BATHTUBS
Thank you for purchasing a “BAS” brand bathtub. “BAS” hydromassage baths are modern technologies and original lines that provide the comfort of hydromassage, which will improve your health and give you many pleasant moments. This manual describes the bathtubs' functions, installation requirements, care and operating methods.
ATTENTION:
In order for the bath to be beneficial for you, to work for a long time and reliably, a number of conditions must be met:
If your body has problems with the functioning of the cardiovascular system, then consult a doctor (to what extent is hydromassage beneficial for you).
Consider installing filters (for water purification) - this will increase the service life of your faucets and hydromassage bath equipment.
Do not turn on the hydromassage without filling the bathtub with water.
TECHNICAL DESCRIPTION
Standard equipment for a hydromassage bath:
Acrylic bathtub – hydromassage – 1 pc.
Acrylic panel – 1 pc.
Drain and overflow device – 1 pc.
Legs – 3 - 5 pcs. (depending on model).
Panel clamp – 4 pcs.
Self-tapping screws for attaching acrylic panels – 1 or 4 pcs. (depending on model).
TRANSPORTATION OF BATHTUBS
When transporting and installing the bathtub, care must be taken not to damage the piping and electrical systems. DO NOT carry the bath by the pipes and nozzles.
INSTRUCTIONS FOR PREPARING A SITE FOR INSTALLING BATHTUBS: 
A plumber who carries out work on hot and cold water pipes must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may rest against the stiffeners, units and fittings of the bathtub. This means that the bathtub cannot be installed close to the walls.
The bathroom drain pipe should not rise above the floor by more than 10 cm. If this cannot be ensured, then a podium must be made.
The legs serve to level the bathtub, so additional supports must be installed under the supporting structure of the bathtub.
Electrical wiring must have multiple insulation access to exposed contacts, at least 3 mm thick. System protection must be based on differential (multiple) shutdown (1 fn =30 mA). The supply cable must comply with EEC standards or be type H07 RN-F, according to VDE 0250. Near the bathtub and in a place protected from water (recommended minimum height from the floor 25 cm), a socket should be installed with (make sure that the grounding cable is correctly installed). The baths are delivered ready to be connected to the electrical network. Do not under any circumstances swap installed terminals.
ELECTRICAL SYSTEM
The installation of the electrical system must be carried out by a professional electrician. must have a differential switch 3 0mA, magnetothermo 2.4 - 4A, and another common connection (CEI 64-8). If it does not exist, install one in the apartment’s common panel.
DO NOT INSTALL UNDER THE BATH.
The procedure for connecting hydromassage baths to the electrical network:
Yellow-green wire - grounding;
Brown wire - phase;
Blue wire - 0.
V
220 / 240 Hz
50 W
0.7 – 0,9
depending on the bath model
HYDROMASSAGE EQUIPMENT 
BATH CARE
For daily cleaning of the bathtub, use a liquid cleaner and a soft cloth. To maintain the shine of the bathtub, you can wipe it with a cloth with a polishing agent. Stubborn stains in the bathtub can be removed with conventional household cleaning products. smooth surfaces. To clean the bathtub, use only soft cloth napkins.
Deposits on the surface in the form of scale are removed with a soft cloth moistened with lemon juice or wine vinegar.
Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly sanding with fine-grained sandpaper (No. 1000/2000) and water. You can restore the shine of the surface with a liquid polish.
CLEANING THE BATH HYDRAULIC SYSTEM
This type of cleaning is performed using hard water (over 15 salt deposits per cubic meter of water). It is recommended to clean the bathtub hydraulic system twice a year as follows:
Fill the bath with hot water (40 C).
Pour in liquid detergent at the rate of 2 g per 1 liter of water and run the hydromassage unit for about 5 minutes.
After this, turn off the electric pump and drain the water from the bath.
Fill the bathtub with cold water again and turn on the hydromassage for 2 minutes.
Drain the water and wash the bathtub (see “Washing the bathtub”).
IMPORTANT NOTE
WARNING: Never use metal brushes or tools, or use solvents or detergents containing abrasives to remove dirt from the surface of the spa. Also avoid contact of ammonia or chlorine with brass and chrome parts of the bathtub.
HOW TO USE HYDROMASSAGE BATHS
Never turn on the hot tub until the water reaches 5-6 cm above the jet opening. Never use the bathroom after taking alcohol or taking medications. Hydromassage for medicinal purposes can only be performed on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel drowsy while taking a bath, turn off the hydromassage device for a while and cool the water.
For overweight people, hydromassage baths at water temperatures exceeding 38 C are contraindicated.
Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upward.
SIMPLE MALFUNCTIONS, THEIR POSSIBLE CAUSES AND REMEDIES
| Occurring fault | Possible reason | Remedy |
| No mains voltage | Call a specialist (electrician) | |
| Hydraulic pump does not turn on | The plastic tube connecting the button and the pump has come off the hydromassage button. | Attach the plastic tube to the base of the button and restart the system |
| Jet nozzles are closed | Rotate counterclockwise to open nozzles | |
| The hydraulic pump works, but no water flows from the jets | The piping system is clogged | See paragraph “Bathroom care” |
| Increased vibration in the hydraulic pump | The motor is loosely attached to the metal frame of the bathtub | Tighten the engine mounting bolts |
Processed
REQUIREMENTS FOR THE BATH INSTALLATION LOCATION
Installation of the bathtub should be carried out only by qualified specialists, in compliance with the following requirements:
- Before starting work, it is necessary to check the completeness of the product, cocoa, and screen.
Installation of a bathtub without a frame, as well as with a modified frame, is not allowed. The legs are used to level the bathtub and adjust the gap between the bathtub panel and the floor. The bathtub must rest on all support points to prevent uneven distribution of the load and, as a result, the appearance of microcracks in the bathtub body;
It is not allowed to embed the bathtub in tiles, panels or hard mortars. To avoid moisture getting under the bathtub or on the hydromassage equipment, the seams between the bathtub and the wall must be sealed with plumbing silicone.
Avoid contact with dirt and construction dust onto the surface of the bath. This may cause clogging and failure of the hydromassage equipment or lead to scratches on the surface of the bathtub during subsequent unprofessional cleaning.
When carrying out work on the removal of water supply and sewerage pipes, it is necessary to take into account the linear dimensions of the bathtub. Otherwise, the connection may be difficult, since the pipe outlets may rest against the stiffeners, units and fittings of the bathtub, and the bathtub cannot be installed close to the walls. Structural changes in the arrangement of equipment and pipelines of the bath, cutting of mounting clamps, and so on are strictly prohibited.
The electrical wiring of the room must have an individual differential switch 30mA, magnetothermo 2.4-4A or another common connection (CEI-64-8) and installed in the common switchboard of the room. It is strictly forbidden to install this switch under the bathtub!
ATTENTION! Failure to comply or not to fully comply with the above requirements does not provide for the preservation of warranty conditions for service or repair for such a bathtub.
BATH INSTALLATION
Install the bathtub on the legs (Fig. 1). The manufacturing company allows the legs to be equipped with an M12 bolt, instead of the corresponding threaded rods. Legs of configuration A (Fig. 1) (2 pcs.) - installed on the front (front) side of the bathtub, along the edges, left and right (for the RIVIERA bathtub - 4 pcs., all in front). Legs of configuration B (Fig. 1) - other remaining front and rear legs. The legs are connected to the frame using the upper pair of M12 nuts, which also serve to adjust the height of the bath. Install a drain-overflow device on the bathtub (Fig. 2), a siphon (may not be included in the kit), and adjust the bathtub in height. The distance from the floor level to the bottom point of the siphon must be at least 15 mm. Make sure that the bathtub is adjusted and rests on all points of support. Install the panel onto the bathtub by snapping it onto the upper fasteners (Fig. 6 and 7). On some models of symmetrical and asymmetrical “BAS” bathtubs, it is possible to trim the panels to length (no more than 2 cm per side). In addition, if you plan to install a side panel on your bathtub, then first install the top fasteners under it that come with the side panel. Adjust the verticality of the panel. The bottom of the panel should be adjacent to the plane of the corner corner installed on the outer legs. The seating depth of the angle is adjusted by the lower pair of M12 nuts. The corners should be equally adjusted in height and be symmetrical relative to the panel. Using a drill with a diameter of 3.5 mm (the size indicated is for a 4.2x25 mm self-tapping screw), drill in the lower corners and panels through holes(Fig. 4 and 5). Remove the panel from the bathtub and connect it to the sewerage and water supply systems (see Connecting the bathtub to the water supply and sewerage network), as well as to electrical network 220 V (see Connecting the bath to the electrical network). After this, carefully move the bathtub tightly against the wall, and once again make sure that it is stable at all points of support, and all connections are made correctly. Place the panel on the bathtub and fix its bottom in drilled holes self-tapping screw with a press washer (Fig. 8).Close the head of the screw with a decorative plug (Fig. 9).
ATTENTION! TO AVOID MOISTURE GETTING BEHIND THE BATH, MUST TREAT THE SEAM WITH PLUMBING SILICONE AROUND THE ENTIRE PERIMETER OF THE BATH!
CONNECTING THE BATHROOM TO THE WATER SUPPLY AND SEWERAGE NETWORK
The connection of the bathtub to the water supply and sewerage network must be carried out by a qualified plumber. The bathtub kit includes a semi-automatic drainage device, which, after installing it on the bathtub, is connected to sewer network stationary, through flexible corrugated or rigid PVC pipe(not included). A sewer drain with a diameter of 40-50 mm is installed at the bathtub installation site in the floor or wall, taking into account the linear dimensions of the bathtub. When placing the drain pipe in the wall optimal height the distance is considered to be no more than 2 cm from the floor level to the bottom edge of the pipe. Connecting the bathtub to the water supply network if it is equipped with a mortise mixer. The network pressure should be 3-5 atm. At pressures above 5 atm, pressure reducers should be installed and adjusted to the specified standards.
Places for connection to the water supply system must be placed taking into account the linear dimensions of the bathtub and its units and equipped with taps disconnecting from the main line. Connection to the system is made through a flexible plumbing line ( water hoses). The length of the hoses must allow the bath to be moved from the walls and a distance of at least 0.5 m. It is recommended to use water purification filters. The absence of filters can lead to clogging of hydromassage nozzles and metal scale entering the ceramic mixer cartridge, which will lead to their failure.
