What is the name of the thing where the wires are hidden? How to hide wires in an apartment: basic tricks (51 photos). Hiding wiring and low-current wires

Before repairs, they usually think through work with electrical wiring, solving two interrelated problems: how and where to hide wires in an apartment and how many sockets are needed ? The preparation of this plan depends on many reasons, but without an idea of what, where and how the furniture will be placed, it cannot be solved. Finland has very strict rules fire safety, therefore, at the request of friends who asked where our wires are, if they are not visible in the photographs after the repair, showing those electric installation work, which we spent at home, it must be said that we did everything possible to ensure that, while observing the rules, our electrical wiring was laid in accordance with our personal ideas about comfort.

During the renovation process, we partially replaced the electrical wiring, and hid the wires in special plinths for electrical wiring. And if you click on this photo, you can go to the post where I tell you how they built it in Finland 50 years ago, what we encountered during the renovation process, and specifically about the state of the electrical wiring before it.
And in this post I show all the wires and sockets in our apartment, and how they are hidden.

In the previous photo in the living room, the large flower is covering the baseboard for the electrical wiring and antenna and outlet, so we'll move it over and see how it's done.

Directly from the TV there is a single plinth, inside of which there is not only electrical wiring, but also an antenna, and from the outlet there is a thinner plinth just for the antenna. The electrical cord from the TV is plugged into a socket using a regular plug.

We had to cut off the regular outlet from the extension cord and install a smaller, flat one so that it would fit behind the TV, because we couldn’t find a long cord for it. I already told you about it, the distance from it to the wall is 2.5 cm.

The terrarium, because it stands sideways, could not be connected via the plinth, so the wire for it is an ordinary white one from an extension cord, but the plinth for the antenna ends and a piece of wire also sticks out, because we didn’t want to glue the plinth onto the wallpaper, it’s ugly. And internal wiring in the wall is prohibited due to local safety regulations.

In the bedroom, I managed to twist the bottom around the mechanism so that they are no longer lying on the floor, which I complained about in the post that they were too long.

There is a second outlet in the bedroom that we don’t use, but I didn’t bother to remove it because the curtain is constantly covering it.

Inside the kitchen cabinet there is a socket for the hood and with it light bulbs for light above the stove.

The main outlet in the kitchen above the desktop looks like this: for a kettle, coffee pot, tablet and basically anything that needs to be charged.

I call the additional outlet in the kitchen a guest outlet, because friends and relatives who stay with me plug in their computers and work in the kitchen. Also, a Christmas sixteen-candlestick sticks into it when it stands on the window on New Year's holidays. It was also impossible to install my favorite flat sockets in the kitchen due to safety precautions.

In the bathroom, the main socket is above the lamp, it is connected to an electric toothbrush, and it is also used for a hair dryer.

It would have been impossible to remove the additional outlet in the bathroom anyway, so I left it just in case: you never know, maybe when we buy a washing machine and dryer.

A plinth for electrical wiring stretches from the distribution board in the hallway washing machine and ovens.

It runs along the corner along the mirror and ends at a regular baseboard. A hole is drilled from there and then it is laid behind kitchen cabinet before dishwasher And electric oven.

I don’t like modern sockets because they are convex and collect dust, so I didn’t replace the flat ones that were in the apartment.

This is the only outlet in the office, and the computer wires, unfortunately, lie on the table, and I still can’t imagine how to hide them. They collect dust, but I wipe them regularly when cleaning as necessary.
The conclusion that I made for myself in the process of organizing and planning renovations: the main thing is not the number of sockets in the apartment, but their thoughtful use for connecting the necessary household appliances, because electric wires They collect dust in the apartment and need to be hidden .
What do you think, friends?

We choose wallpaper with a cute flower or a fashionable snow-white finish, shabby or, on the contrary, ultra-modern furniture, napkins that match curtains and cushions on chairs - in a word, we create a special small world with a unique style. But there are things that cannot be avoided in our age of progress and which, taking advantage of this, impudently spoil the entire idyll we have carefully created. These include, for example, electronics and Appliances. However, manufacturers began to produce equipment in a large assortment suitable for different styles, and in embedded versions. Another enemy is the wires stretching from this very equipment along the walls and floor. For those for whom they are an unbearable eyesore, we offer several ideas for disguising them.

We all know that most often the wires are hidden under the baseboard, and they try to match the sockets to the color of the finish and buy them with special lids that ensure safety for children and a more attractive appearance. But what to do if, for example, a new Internet operator came to you and installed new wires? Or have you decided to move the TV to that corner of the room where there is no outlet? Why not redo all the repairs because of this? You can always be creative and block off the wires, for example, with a decorative fence. And block the outlet or new Internet router with some kind of homemade barrier, turning the unsavory element into an art object. The example below shows an easy-to-create geometric iceberg.

To ensure that the wires lie behind such fences without bristling, another well-known way to make the appearance of the wires more neat will help us - zip ties.

You can make these clamps yourself from regular Velcro. Velcro clamps are also quite easy to find on sale; their significant advantage is their reusability.

You can also make homemade fasteners for wires from office clips. Clips as clamps can also ensure their fixation to the wall. From the same clothespins you can make a separator for the charger inputs.

While the idea of using wire clamps is obvious, not all of us realize how useful they can be in ordinary life. Here's an example of how the look of your desktop changes thanks to these simple things.

Now on sale you can find very nice versions of clamps, for example, in the form of leaves.

There are also camouflage covers for wires based on the same plant theme.

You can play up the look of wires stretching across the room with the help of improvised means, stickers and your own drawings.

If the insulators on your wires are at least a little similar to aesthetic ones, you can not disguise them at all, but, on the contrary, make them an object of design art and general attention. Here are some examples for inspiration. This idea is especially suitable for loft-style interiors.

Wires hanging from the desktop, if your desk is against the wall, can simply be curtained.

Or reason with the help of special hanging hammocks.

Such a device can be ordered from, where there is another gadget for pacifying tangled wires.

You can find similar separators for wires and charging inputs on sale in the form of boxes.

However, it is not at all difficult to make such a separator yourself, for example, from a shoe box. Your new desktop device will look especially beautiful if you wrap the box beautiful paper or cloth.

Completing renovations in a home or office, as well as carefully masking existing wires, should not relax the owners. Mounting a new TV on the wall, replacing a computer, installation burglar alarm or additional wiring to power electrical appliances leads to the appearance of new switching. All this carries additional risks for children, animals and the appearance of the interior. What methods of camouflage are most effective? How to hide wires in an apartment in compliance with safety regulations and preserving design? Let's consider these points in more detail.

Internal disguise

The best option is to hide the cables at the stage of major repairs. There are several ways here.

Conceal the wires in the wall. This technology can be used before or after wallpapering. To begin with, the paper is cut with a sharp knife, after which the edges are moved apart and fixed with needles. Next, using a puncher or manually, a groove is made for masking. After completing this work, the cable is laid in the prepared recess , and the groove is closed with alabaster or plasticine. The final stage involves applying glue to the wallpaper and fixing it in place.

How to hide wires under wallpaper is shown here:

Hide wires in the floor. There are several options here.

Conceal the wires in the floor plinth, where there is a cell for wires. When purchasing, it is important to pay attention to the design of the product, in the central part of which there should be a special recess. This is where the wires are laid. This method is distinguished by its versatility and ease of execution.
Hide the wiring in the groove. The principle here is the same as in the case of wall mounting. Using a hammer drill, a recess is made into which the excess commutation is placed. After this, the groove is filled with cement and leveled to the floor level.
Fill with cement. If the quality of the flooring in the room leaves much to be desired, you can make a new screed by hiding the wires in it. The latter should be corrugated.

Remove wiring from the ceiling. Option two:

Hide the wires in a plasterboard niche installed around the perimeter.
Hide the wires in the gap between the tension fabric and the main ceiling. In the latter case, it is worth warning the craftsmen in advance about your decision, otherwise you will have to use other options.

External camouflage

If the methods discussed above are not available for implementation, do not despair. To beautifully and wisely hide numerous cords, you can use the opposite method, which involves external camouflage. If you approach the issue wisely, numerous wires will in no way spoil the interior, but, on the contrary, will give it exclusivity and an unusual appearance.

Let's look at how to hide the wires outside. The options are as follows:

Imitate a tree branch. You can easily decorate a computer or television cable by using it to create a small branch decorated with homemade flowers, leaves or birds. This solution will transform the interior, giving it uniqueness and brightness.
Make a tree. If the wire is one and a half meters long or more, there is no need to cut it - it will turn into a nice “tree”. Used to secure the cord special fastenings, with the help of which the necessary outlines are set.
Power station. Lovers original design can imitate supports on which the wires will be attached. This method allows you to solve two problems - make the wires invisible to the eye and create a basis for teaching your children.
Complex drawings. If you have free time and imagination, you can hide the wires on the wall by creating an original landscape. Here the main emphasis is on the contrast between the shade of the wallpaper (paint) and the cable. Separately, it is worth considering elements that allow you to highlight the wiring.
Fence. One of best options- fastening the wires in the upper part of the baseboard. But to hide them from view, you should make wooden blanks shaped like a fence, and then secure them with double-sided tape. This method is suitable for a corridor or a child’s bedroom. For greater originality, each element of the “fence” can be painted in a different color.
Car track. This option is the most labor-intensive, because its implementation requires time. To create a road, cardboard is used, from which the required object is cut out. Next, the paper is painted in a color that matches the interior.
Other methods. In addition to the options listed above, wires can be hidden under door frames, behind indoor plants, under the carpet or behind furniture.

Remember that it is better to develop a plan for masking wires in advance, and then strictly adhere to it.

Lots of creative ways to hide wires are shown in this video:

Hiding cords from the computer

Despite the popularity and availability of wireless technologies, many devices still require a wired connection. One of them is a computer, after installation of which a whole “web” of cords is assembled connecting the system unit with the monitor, power supply, printer and other devices.

How to remove all cables from under your feet without disturbing overall design rooms. There are several options:

Hide the wires and extension cord in a special box. To implement your plan, it is enough to find a box of a suitable size, make several holes in it, and then disguise all the switching in it. As an example, it is possible to use a Plug Hub box made of special plastic. Its peculiarity is the absence of a bottom and holes provided in the upper part. This “box” can be attached to the floor or to the wall.
Fixing cables under the tabletop. To the most simple options This includes masking the switching under the table, which will require binders and short screws. Make sure that the length of the latter is 20-30 percent shorter than the thickness of the top of the table. First, an extension cord is attached under the tabletop, after which the wires are collected into a bundle and clamped using binders secured with screws. There are other options - fastening the power cables using construction stapler(special clamps are used) or regular ties. In the latter case, the wires are pulled together into a common bundle and fixed to the table leg. The part of the switching that comes from the baseboard can be covered with plastic, matched to the color of the flooring. The filter outlet should be hidden under the tabletop, secured with wide Velcro (the latter is secured with screws). To prevent wires from dangling, the switching is placed in small cable channels, which are fixed using insulating tape or a simple plaster.
Creativity. As discussed above, the cable does not have to be hidden somewhere. One option is to fix it to the wall using clamps and then “attach” a bird cut out of a magazine. If you have available funds, ugly chargers should be replaced with products of a more original design.

Fixing wires under the table using binders is shown in this video:

and one more option:

Properly hidden wires are a chance to improve interior design and eliminate the risk of damage electric shock children and pets, as well as get rid of the “cobwebs” from under your feet. But, in addition to the secrets already discussed, it is worth considering a number of recommendations:

It is important to store numerous cords correctly. To do this, all switching from the set-top box, phones, computer and other equipment is put into a special box. To avoid future confusion, the purpose of each cable is signed. To avoid intertwining wires, you should use zip ties.
If the wire is needed regularly, you can fix it around the perimeter of the table on the underside of the tabletop. With this fastening, the cord is easy to remove and connect to the device at any time.
During the masking process, it is important to mark each cable on one side and the other. This precaution allows you to avoid confusion in the future, when the purpose of each switching element is already forgotten.
IN construction stores a wide range of special boxes made in different style and capable of completing the assigned task. You can easily hide wires in them and not worry about interior design.
When using fabric braiding, it is important to ensure that it does not sag. Otherwise, the risk of fire increases, and appearance This product leaves much to be desired.
The power cable should be as short as possible. In this case, the risk of injury from electric shock is reduced and the masking process is simplified. If small children live in an apartment (house), it is worth remembering the danger posed by power cords. That is why it is advisable to hide the wires immediately after installing the equipment.
Cables performing different functions must be separated from each other. Thus, the wires for powering a computer, printer, music center and other devices are connected separately from the power cords through which voltage is supplied. Thanks to such forethought, it is possible to minimize the interference that causes noise and interference.

Results

It’s not difficult to tidy up your interior and protect your loved ones by masking wires, because there are many ways to do this. effective ways. The main thing is to decide on a suitable option, think through the switching layout in advance, and purchase necessary materials and follow the advice outlined in the article.

It is important to understand that TV is not only a screen. A huge number of different devices are connected to the TV device: speakers, subwoofer, laptop, receiver, etc. Add to this the power cord and antenna cable. It is not surprising that all users have a question: how to hide the wires from the TV on the wall, in the floor, or decorate them?

Now let's look at 5 main ways to disguise all cords. Let's determine where it is better to hide the wires. Let's give real examples with photographs that confirm that it is indeed possible to hide all communications.

into the wall

Hiding the cables is not difficult. Especially considering the fact that masking various communications is a real trend in the world of interior design. Very often you have to run the antenna cable across the entire apartment. This violates the aesthetic picture. Therefore, new ideas on how to hide wires from the TV will be more useful than ever.

Remember that the antenna cable is not the only wire that connects to the TV device. Keep in mind that you also need to disguise the power cord. Many owners of modern equipment connect an Ethernet cable to a LAN connector. Add to this an HDMI cable, which is used to connect additional devices.

To solve this problem use floor skirting boards with cable channels. They allow you to hide the wires. What to do if the TV is hanging on the wall? You will have to pull the cables out of the baseboard to connect them to the TV. It is clear that such a solution can hardly be called optimal. Therefore, it is wiser to hide communications in the wall.

What is the easiest way out of this situation? Twist the wires into a bundle using nylon ties. Try to disguise the cords somehow. This method absolutely cannot be called ideal, but it has the right to life.

A fundamental, but very labor-intensive solution is laying wires in grooves. Special holes need to be made during repairs. Don't forget to install a TV outlet on the wall. This is the most accurate and technologically advanced way. None of the guests will accidentally touch the wires. Also, the cords will be kept out of reach of pets. All wires are output to a single console, which contains the necessary connectors.

To route wires along grooves, it is absolutely not necessary to chisel the entire wall. Stretch them all the way to the baseboard, and then hide them in it. The main disadvantage of this method is that it is suitable only for those owners of TV equipment who are renovating their house or apartment.

How to hide wires in the wall under the TV if you have just recently finished finishing? The optimal solution is to decorate the cords, but we’ll talk about that a little later. Now let’s analyze how to hide communications for a TV on the wall.

First, think carefully about where exactly the TV will be located. Mark the location of the device on the wall. The second stage is the choice of bracket. This aspect is of enormous importance. Despite the global VESA standard, which includes the most popular mounting points, the brackets themselves come in different shapes and sizes.

Think carefully about the best type of bracket to choose. If the mount is too massive, it will interfere with commutation. An incorrectly selected bracket size will cause wires to fall out from behind the TV screen.

To make accurate measurements, you must first buy a TV. When the device is at your home, measure the dimensions, and then buy a special bracket. Try on the TV mount, measure the distance that remains to the edges - at this distance you need to make sockets.

The measurements taken need to be transferred to the wall, and then you can start working. Using a grinder, cut 2 vertical strips in the wall. Their depth should be literally a few centimeters. The distance between the stripes is no more than three centimeters.

Hollowed out using a hammer drill inner part. This allows you to form full-fledged grooves. Make several holes using diamond crowns. Sockets will be placed in them. All necessary outputs should be located here: power supply, antenna cable. Consider how many power points you will need. This depends on the number of equipment connected to the TV.

That's it hard work completed. Place all the cords in the grooves made. All wires are first secured with plastic staples. If this is not done, then they will constantly fall out, interfering with subsequent wall finishing.

The ends of the wires must be connected according to the appropriate diagram with the socket. Then it needs to be installed in a specially designated place. The grooves should be sealed gypsum plaster. Final stage – finishing. Install the bracket and fix the TV on it. Connect all wires to the TV.

To the floor

The second way is to hide the cords under the floor. Today in construction stores you can easily buy special skirting boards equipped with a niche for masking the cable. You just need to remove the outer panel, and then remove the wires into this space. Then install the panel back.

The main advantage of this option is efficiency, cleanliness, and simplicity. Work takes up minimal free time. To cover the cords under the baseboard, you don't have to hammer anything. No dirt, etc. Antenna and Internet cables can be placed under the baseboard. With their help, other communications are also masked.

The antenna cable of the TV can also be hidden on the floor, or rather under it. How can I do that? Take a hammer drill, and then make holes in the floor, which will actually be intended for the wires. Use corrugation to create a protective layer, and then you can lay the cords.

When installation is complete, level the floor using a mixture of sand and cement. If the apartment has a wooden floor, then you will need to dismantle the boards and place the wires in a metal tube.

In cable channel

A special box also allows you to hide the wires. However, this is a less aesthetic option. The user can make a cable channel independently or buy a ready-made one in a store. Hiding wiring in a box is much easier and faster than making special holes in the floor.

Having carefully studied the assortment of special stores, we come to the conclusion that users are offered several types of cable channels. The simplest option is PVC boxes. Absolutely everyone saw them. This is an ordinary cable channel made of plastic. Most often they occur white. The removable cover is held in place by latches.

Is it possible to fit a PVC box harmoniously into the interior? This is possible, but only on condition that the color of the cable channel matches the palette of the room's interior. It is important that it does not blend into the interior, but at the same time does not look too catchy.

Perhaps the rarest option is models made from MDF. Such boxes will fit harmoniously into classic interior, which contains wooden furniture and various interior items.

Metal cable channels are made primarily of aluminum. This product looks really very impressive. The box will fit harmoniously into a futuristic interior.

In structure, all the models listed above are very similar. They are fixed to the wall using special dowels or glue. The connections along with the cords are hidden under a decorative cover.

Sometimes it is much easier to make a cable channel yourself than to look for suitable option in shops. The quality of the product and its appearance directly depend on your skills and abilities. The type of material used is also important. Working with PVC is much easier than working with metals.

Do you want something original and non-standard? You can make a cable channel from planed boards. The wires will be located between them. The wires will be covered with a decorative cover on top. As for the boards, they can also be painted in any color. Which will make them not stand out from the overall picture of the interior.

Under furniture

Mostly we hide the wires behind the TV. It is clear that if you look closely, all the cords will be visible. However, today you can buy special furniture that allows you to hide all communications.

To a greater extent we are talking about TV stands. They are equipped with special holes in which wires can be placed. It is very comfortable. Not to mention the fact that the cables will not be visible and therefore will not disrupt the interior design. Special headsets, which have an area intended for installing a TV, also allow you to hide the wires.

Cable as an interior detail

Perhaps the easiest way is to decorate the wires beautifully. You can hide the cords behind live or artificial plants, original driftwood, and curtains. To disguise wires, it is not necessary to make them invisible. Communications can be turned into a decorative element.

To decorate the cables, you need to take into account the style of the interior. Let's consider the most popular trends in design, as well as specific recommendations from professionals:

Loft - use special channels presented in the form of a layout of small bricks;
Classic interior - use additional wooden panels for masking wires;
Hi-tech – you can hide the cords in metal pipes; secure them to the wall with screws.

To achieve an impressive result, entrust this work to professionals. Not everyone has the appropriate skills. Specialists with experience in carrying out such work will be able to do everything efficiently and quickly.

If creative thinking is developed at the proper level, then you can do the decorating yourself. There is absolutely no need to buy additional expensive materials. The means at hand will be more than enough. The chosen method must match the decor.

For example, if the length of the wires allows, then you can make a drawing from them on the wall or geometric figure. The main thing is that your composition fits harmoniously into the design of the room. First you need with a simple pencil make a sketch of the future drawing. Once the pattern is applied to the surface, you can decorate the wall with cables.

The method of fixing the wires is another very important point which needs to be thought through in advance. For example, nails are absolutely not suitable for us, since they will damage the cord. It is better to choose tape or glue. This method of decoration is a very simple disguise of cables.

What to do if patterns and all kinds of ornaments do not fit into the interior or the wires are too short? Use additional edging to turn a regular cord into decorative element. This method is especially relevant when it comes to children's rooms. You can use all kinds of stickers to hide cables and maintain the integrity of the interior.

Sometimes, when purchasing new equipment or after repairs, the wires in the apartment remain lying on the floor or hanging on the wall. They seriously spoil the appearance of a home, and can also cause a person or electronics to fall. You need to clarify in advance how to hide the wires so as not to spoil the design and make the house safe.

Internal placement

When in the apartment, the house begins major renovation, the wiring is most often recessed into the walls. First, using a wall chaser, drill, or hammer drill, grooves are made in the wall, into which the cables are then hidden. Posting to wooden house be sure to be placed in a protective corrugation - a shell that will protect them from adverse effects and prevent damage.

Communications remain open when cosmetic update home or when installing new sockets and switches. If you wish, you can always correct the situation without extra costs. There are several methods to hide wires with your own hands.

On the walls

It happens that the wallpaper is already pasted, and you don’t want to violate its integrity. There is an option to eliminate protruding cables without causing serious damage:

carefully cut the wallpaper or bend it away from the wall close to the floor;
take a convenient one construction tool, make a neat shallow channel in the wall;
lay the wires in the resulting hole;
close the channel with a thin layer of plaster or putty;
let the solution dry;
glue the wallpaper in its place.

If this method is not suitable, you can proceed without gating - use a decorative box for wires. It is especially common to cover power wires with boxes: they have large diameter, therefore, without repeated repairs, it will not be possible to recess them into the wall. It is necessary to buy a cable channel suitable in color, width, length, which will serve additional element decor and will reliably protect the wiring.

In a wooden house, the box will enhance fire safety measures. This option is also ideal for the bathroom, because it is very difficult to lay wires under the tiles. It is only important to remember that all lighting elements, electrical wiring, and cable ducts must be waterproof.

How else to beautifully hide wiring on the walls? If desired, it can be covered with the following finishing elements:

door frames;
various moldings, baguettes;
window slopes.

It should be noted that only low-current wires (for example, for the Internet, telephone) can be covered with such materials, and high-voltage cables can only be hidden in accordance with fire safety standards.

On the floor

Wiring is often routed along the floor, and here it is even easier to hide it than on the wall. During repairs when laying the screed, you can stretch the cables in corrugation and fill them with cement on top - the communications will be reliable and durable. If flooring is already there, it’s easy to carefully remove it, punch out the recesses with a hammer drill, then drown the wires in them and cement them. Under wooden floors you will have to lay the cables in metal pipe, after removing the boards.

The stores offer a wide range of floor skirting boards with a hole for wires (with a cable channel). The central part of such a plinth is removed, the cables are laid in the niche, and then the removable element is returned to its place. Working with such skirting boards is convenient, quick, there is no dust, dirt, and the floor material does not deteriorate.

The procedure for laying wires under the most popular coating - laminate - is as follows:

remove part of the lamellas under which the cable will pass, right down to the construction logs (bars);
place the cables in the corrugated pipe along or across the joists, if necessary, cutting out space in the wood for the crossing of the wires;
return the soundproofing pads and lamellas to their original place.

On the ceiling

It is also possible to hide wiring on the ceiling, but the method will depend on the type of coating. Often used in homes and offices stretch ceiling, which take up extra space, but provide the opportunity to route wires as users need. There are practically no obstacles for the cables, so it is possible to route them along the shortest path. This has a number of advantages:

cost reduction;
reduction of work time;
reducing the overall circuit resistance;
strengthening fire safety;
possibility of easy wiring replacement.

According to fire safety rules, it is necessary to cover wires and bundles of them. corrugated pipes. Do the same with wiring under suspended ceilings, niches or complex structures from plasterboard. It is best to connect communications into a single highway, which will facilitate repairs in the future. If the ceiling is concrete, you will have to drill grooves in it and lay wires in the same way as is done on the walls. This method is very labor-intensive and is rarely practiced.

External camouflage

If they have an artistic taste, many people prefer to decorate rather than hide the wires. From standard wiring it is quite possible to make a real art object, painting, panel with your own hands. Typically, cables come in black or white, but if desired, you can find a material of a brighter shade.

Next, you should choose a drawing that suits the style of the interior, sketch it with a non-greasy pencil directly on the wall. Afterwards, you need to measure the length of the circuit using a thread in order to purchase the missing amount of cable (part of it will only serve a decorative role).

You can make any wall pattern out of wires. Often the following are taken as a basis:

branch with leaves, sitting birds;
one or more trees;
giant light bulb;
power station;
highway (in the nursery);
decorative fence.

The wires are attached to the wall with special fasteners, which can then be decorated with any suitable material– fabric, special paper, designer decorations. Also, ugly protruding wires are hidden behind high indoor plants, well-placed furniture, carpeting, door and window frames.

Hiding wires from TV and computer

Usually the TV is placed in plain sight, so the long cable from the equipment will also be visible to everyone. Most often, during repairs, they immediately determine a place for the TV, installing sockets behind it, and leading the wire out of the wall. It is recommended to carefully peel off the wallpaper, make a groove for the wiring, place it in the hole, drowning it in the corrugation. The wires are fastened using brackets.

Near computer desk There are almost always a lot of cables, because printers, modems, routers and other devices are connected to the system unit. To hide the “tangle”, you can do the following:

attach the wires to inner surface table with self-tapping screws, reliable tape, construction staplers;
beautifully decorate a shoe box, a plastic box, cut holes and release wiring;
sew a fabric cover, attach it to the table top or to the back of the furniture from the inside;
connect the cables with office clips to the furniture;
hide the wiring in a single “hose” that will prevent confusion.

In order not to get confused when masking the wires and not to get into trouble during repairs, they must be marked in advance. This will help you immediately find the right cable later. It is better to separate low-power wiring from power wiring, without connecting it into a single bundle. Wires from the antenna and the Internet should be placed separately from others so as not to spoil the signal quality.

Cables should be as short as possible and minimal amount connections: this increases their safety and reduces the risk of injury. It happens that the braid of hidden cables frays due to poor placement, so in dangerous places the wiring must be checked more often. If you need to mask wiring, you can use any ideas, especially since the range of tools and materials for decoration is now huge!