Swings from slats. Do-it-yourself children's swing for giving: photos, diagrams, useful tips. What functions can a swing perform

Everyone wants to have at their disposal a beautiful and comfortable corner for relaxation. For many, the dacha becomes such a paradise. How to arrange a summer cottage so that it always gives you a good mood? Let's fast forward to childhood for a moment. Remember how much pleasure you got from such a simple thing as a swing. They are fun for both kids and adults.

Making a swing for a summer residence with your own hands is not so difficult. If you have at least a little plumbing and installation skills, this task will not cause you much trouble.

Swing designs are very diverse. Here may be present as budget options concocted from the remnants of construction, and real masterpieces of architecture.

You can buy ready-made wooden swings for giving good quality at good prices at Kupistol.

Types of swing for a summer residence

swing-scales are a children's swing for a summer residence. The principle of the device is a board with two seats, in the middle there is a metal pipe on two racks;
a simple swing on two ropes is the most simple design.. Sitting board suspended at two points;
swing-sofa on four ropes - the most common type of country swing. They are a bench with a back, suspended at four corners.

Swings can also be divided into stationary and portable. In the second option, the swing can be removed for the winter indoors, moved around the site at your discretion.

Swings can also be divided into stationary and portable.

Material for manufacturing

For suspension components, the following materials are used:

rope;
cord (rope for mountaineering);
steel rope;
a chain with a medium-sized link;
steel bar;
steel pipe.

For the manufacture of the seat, you can use:

wood - boards, plywood;
wood laid on metal corners;
metal - rod, strips;
plastic - for child seats.

Swing supports

Simple swings can be hung almost anywhere. Most often choose a strong bough. You can also fit a crossbar between two trees.

For a swing sofa you will need strong supports. They can be:

wooden - two supports crosswise;
metal - two supports dug into the ground or with a square frame at the bottom;
metal - one pole, reinforced with a concrete screed.

How to make a simple swing in the country

The simplest option, which is perfect for children, is a simple wooden swing. If there are no suitable trees in the recreation area, you can build supports from four logs. We bury the ends of the support into the ground to a depth of about 70 cm, at the top we connect them with a stud or bolts with washers. Please note that the angle between the posts must be quite large for the stability of the structure. The fifth log will serve as the upper crossbar, we also fasten it with bolts. With the help of fasteners sold in any hardware store, attach a rope to the crossbar (strong cord, metal cable). We make a seat from a board 30-50 mm thick, with the help of hooks we fasten the cord. The cord can be tied or special clips can be used. You can hang such a swing on four ropes. In this case, at the top, the cable is threaded into a hook or ring so that it does not slip, under the ring it is intercepted with a clamp.

You can hang such a swing on four ropes.

Wooden beam option

For the manufacture of such a swing, you will need a wooden beam and slats. Supports made of timber can withstand a load of about 150 kg

A wooden beam measuring 10x10 cm will increase the strength of the swing, but will lead to a heavier structure. It is better to use material with a section size of 5x10 cm.

We assemble the support from the beams, starting from the bottom frame. We calculate its dimensions by adding 40-50 cm to the seat dimensions. vertical bars, forming a triangle. From above, the structure is fastened with a vertical crossbar. All main fasteners are made using metal corners and self-tapping screws. For reliability, we attach another horizontal bar between the two racks of one side.

We make a bench, starting with the frame. Separately from the bars we make a frame for the back and for the seat. We fasten the material from which we planned to make a swing onto the frames. It can be a board, slats or plywood.

From above, the structure is fastened with a vertical crossbar.

We connect the finished back and seat together using metal corners. Before that, we determine the comfortable seat angle, on average it will be about 120 degrees.

We make armrests for the bench from rails, we also fasten them with self-tapping screws.

TO upper crossbar we hang the swing on a chain or a metal cable. Metal brackets or hooks are used as fasteners, we fix the chain on the back and on the swing seat with them.

The swing for the dacha is ready. The height of the swing is adjusted so that the legs of the person sitting on it reach the ground. Such a design can be easily transferred. When standing on the ground, the lower beam must be treated with a protective solution.

Swing for summer cottages made of metal

Such swings are more durable, depending on the design, they are designed for a weight of 300 kg or more, but they will be stationary. Crafting requires skill. welding work. If desired, a small swing of this type can be made mobile by expanding the distance between the lower ends of the supports and welding the base frame onto them.

For racks, choose one of the following materials:

steel pipe with a diameter of at least 5 cm;
metal channel or profile;
steel corner.

Using welding, we connect the pipe, starting from the base of the structure. We get a rectangle, we put two triangles on it vertically, at the top we connect it with a horizontal crossbar. The cutoff angle of the pipe at the top junction of the sides of the triangle is 45 degrees. On the upper crossbar we weld loops from reinforcement.

For manufacturing, you must have the skill of welding.

A variant of the support design - without a lower rectangle. In this case, the racks must be buried 1 meter into the ground; if the swing is planned to be heavy, make a concrete screed.

We make the basis for the back and seat from a metal corner. We make two rectangles out of it, we connect them together at an angle of at least 100 degrees.

At the corners we weld loops for suspension. All metal parts are primed and painted oil paint. We impose on the finished base wooden board, for convenience, it can be sheathed on top soft material or linoleum.

We cover all metal parts with a primer and paint with oil paint.

Choosing a place to install a swing requires special attention. There should be enough space when swinging the swing. It is better to choose a shaded place, if you plan to build a gazebo, a swing can be installed inside it. Wooden crafts must be protected from moisture and precipitation. This can be done by treating the tree with special solutions, if the design of the swing allows it, paint it with paint.

Do-it-yourself swings will give your dacha a unique flavor, create an atmosphere of love and comfort. Have a nice holiday!

Today a large number of people have country houses or dachas - places where you can calmly take a break from everyday hustle and bustle and relax. Today we will tell you how to make a metal garden swing with your own hands for your summer cottage.

This material is conditionally divided into 3 parts.

In the first part: the use of metal to build a swing, and why country builders prefer it. We will talk about the advantages and disadvantages of such structures, calculate the mass of planned attractions, and also talk about the types of attachment for stationary and hanging swings.
In the second part: we will tell you how to make an outdoor metal swing for a summer residence in the form of a bench or a sofa with your own hands, we will also give recommendations on the installation of single structures. And you will also learn how to make a swing seat from a profile pipe with your own hands, as well as a frame.
In the third part: a little about decorating and caring for iron swings, as well as features of the choice in the store.

Advantages and disadvantages of a profile pipe

If you understand in detail the advantages of a profile pipe, you get the following list.

The shape of the pipe is optimized for fast production, which means it is very easy and convenient to work with.
Very economical material, especially when compared with reinforcing structures.
The stiffening ribs, which are located on the structure, greatly increase the upper limit of permissible loads.
The material perfectly resists mechanical damage - it is difficult to deform it with a blow.

However, along with the advantages, the swing from the profile pipe also has its drawbacks:

Most of the operations that can be done with the pipe do not require sophisticated equipment. Except one - bending. It is very difficult to bend it, and all because of those very stiffeners. For this you need a special machine.
Carbon steel rusts easily and is easily damaged by moisture. This shortcoming can be eliminated using the galvanizing procedure, but it also greatly increases the price of the final structure.

Calculation of a profile pipe to determine the mass of a swing

When calculating the size of a swing made of metal, it is necessary to calculate its mass. This will help in the future to determine whether a foundation is needed and what loads the swing will withstand.

When using a square profile pipe with dimensions of 20x20 and a thickness of 1 mm, the weight of one meter of the tube will be ~ 600 g (it all depends on the steel grade).
A 30x30 pipe with a thickness of 1 mm has a weight of 900 g, respectively.
A profile pipe 40x40 with a wall thickness of 2 mm per 1 meter of length will weigh ~ 2300 gr.

Using the data provided, it is easy to calculate the approximate mass of both pipes and the frame of a future garden swing from a profile pipe. We can do this in the following way.

For example, the design uses 8.5 meters of a pipe measuring 30x30x1mm and 3 meters of a pipe measuring 50x50x2mm. Calculate the structural weight:

8.5*900=7650 gr (total pipe weight 30x30x1mm);
Since the pipe 40x40x2mm weighs 2300 g, the pipe 50x50x2 has a weight, respectively, 2300 + 2300 * 0.25 = 2875 g.
3*2875=8625 gr (total pipe weight 50x50x2mm).

Appointment of a profile pipe for a swing

In order to correctly answer this question, it is necessary to explain what types of pipes are used for which parts of the swing.

Round (oval) pipes. Suitable for curved structures (e.g. seats, armrests, arches).
Square and rectangular pipes. They have good strength, suitable for parts that are placed on the surface (vertical racks, spacers).
Flat pipes - suitable for auxiliary elements(horizontal struts).

Swing attachment types and classification

Before choosing a scheme according to which we will assemble a metal swing with our own hands, we need to decide on the methods of attaching them to the supporting structure.

There are two main types of attachments for hanging swings:

on eye nuts;
to nodes.

In the first case, you do the following:

Make through holes in a horizontal beam with a drill (~ 5 mm);
Insert long bolts with washers, tighten the eye nuts;
Attach carabiners and chains or ropes to them.

In the second case, the sequence is:

Throw the ropes over the crossbar;
Making a sea knot
Attach the other ends of the rope to the seat.

Hanging metal swing

Homemade swings for summer cottages made of metal are often quite small in size. These are usually small seats for one person, mostly for children. They do not need a fixed base to hang them in the yard, they only need a tree with thick enough branches or a supporting structure.

Hanging swings are most often hung on a chain or strong ropes - depending on the desire and style. At the same time, you can fix them without damaging the branch itself: wrap the chain or rope with a sliding knot, which will provide a fairly strong grip. The main thing here is to correctly calculate the thickness of the suspension itself.

Chain attachment example.

Drill a large through hole along the width of the seat with a thickness of 7-9 mm (along the red line in the picture);
Pull the chain through drilled hole chain;
Screw the steel bolts along the edges of the seat in such a way as to fix the chain.

Stationary metal swing

Do-it-yourself stationary garden swing from a profile pipe is a more complex option, but no less popular. Great if you need to install seats for two or three people.

For a stationary swing, in addition to the seat itself, it is necessary to make a frame from a profile pipe. This is the supporting element of the entire structure, the heaviest loads will fall on it, so you need to do it with all the attention. Mounting to a stationary frame has several varieties.

Where to install a metal swing on the site

Before you weld a swing or buy it in a store, you need to choose a place on the site, we recommend that you adhere to the following rules:

The swing should be located on open space near the house. Perfect option– 10-20 meters so that you can watch your children play;
There should be no communications above the iron swing (water, power lines and other wires);
There should be no roads nearby (it is best to put a fence around).

Having decided on the place, it is necessary to prepare a drawing-project of your design. We recommend that you specify all dimensions in advance - this way you will save a lot of time and resources for revisions and alterations.

Swing in the form of a bench or sofa with a metal frame

This type of swing is common among manufacturers - today on the market you will find a large number of ready-made assembled models of this type. They are distinguished by practicality and relative cheapness. Such swings are suitable for joint gatherings in the evening after a hard day or on weekends with children and loved ones.

Before you buy materials and start making an iron swing yourself, familiarize yourself with the design features:

given type metal swing for giving can be both portable and stationary;
foundation portable design not required - the support is a square at the base. In case you decide to make a stationary swing, we recommend that you keep in mind the columnar foundation;
a canopy is often made to such structures - it can be either a polycarbonate roof or a stretched awning.

Materials and tools

To make a swing from a profile pipe with your own hands, you will need a whole list of tools and materials:

Round profile pipe for a frame with a diameter of 20 mm, 14170 mm (take a meter or two more with a margin);
4 steel corners;
2 steel arcs, each 250 mm long and 15 mm in diameter;
2 wooden canvases;
a cable, chain or any other suspension that can withstand a load of up to 250-300 kilograms;
welding machine;
pliers;
hammer;
vise;
grinder or hacksaw;
building level;
roulette;
special paint for metal against corrosion;
eye screws 5x80mm, 4 pieces.
shackle M5, 6 pieces;
bolt M6x30, 4 pieces;
nut M6, 4 pieces;
spring washer M6, 4 pieces.

Step-by-step instruction

	Cutting parts from profile pipes for iron street swings. For side racks, you will need pieces of 2500 mm, 4 pieces. On the crossbar you will need a piece of pipe, 2100 mm long.
	We cut off the edge of the pipe at 30 degrees at the end, after which we weld them into an isosceles triangle using a welding machine.
	We measure 2000 mm from the top of the uprights and weld a 1035 mm long horizontal bar to strengthen the frame. See the drawing of a garden swing made of metal, which we made for you with our own hands.
	We weld the horizontal bar at the ends uprights. After that, the seat will be attached to it. The distance between the A-posts is 2000 mm, the crossbar protrudes 50 mm on each side.
	Let's create a swing bench from a profile pipe with our own hands. We take several bars 30x30x6000 mm and shorten them. You should get segments of 1500 mm in the amount of 24 pieces. We clean them with sandpaper or a machine tool. Or you can take a bar 100x100 and fit it to the required dimensions. It is not necessary to cut 30x30, you can use 20x50 and 30x70, etc.
	We apply paint and varnish on the surface to prevent rotting of the wood.
	We make a frame from a pipe 15 mm in diameter. We weld the segments together and attach the bars with bolts. The distance between them is 20-25mm. Along the edges, we weld eye nuts for attaching the chain (two on one side, two on the other). You can also experiment with the distance between the bars (it all depends on their size). More details on the drawing of a swing from a profile pipe.
	We fasten the seat to the vertical posts of the metal swing frame. We drill through holes in the crossbar for bolts with eye nuts. We thread them and twist them. We connect the carabiners with all the eye nuts and attach the chain.
	We dig 4 holes with a depth of 450mm. To do this, we use a hand iron drill.
	Mixing concrete. Add cement, sand and water to the container in proportions of 1:2:3. It is best to use cement labeled as M400.
	At the bottom we fall asleep a pillow of sand 100mm, after which we install the racks in the pits. We throw a few large stones for the stability of the structure, after which we fill everything with concrete. We are waiting for 3-4 days until everything dries. The design is ready

Metal single swing

Do-it-yourself single swings from pipes can be welded both stationary and portable - it all depends on who will use them and how much free space you have on the site.

Stationary swings have the greatest stability of all the listed options: children will not be able to turn them over even during the most active game. However, because of this, they have a drawback - low mobility: they cannot be removed during bad weather. Portable, of course, are not as stable, but also much more convenient than stationary ones.

The main stages of installation

	To weld the swing frame from the profile, you need to take the pipe and cut it into two equal parts, each 3100 mm. Cut the edges of the vertical racks at an angle of 45 degrees. After that, it is necessary to form the letter P - weld the third to the ends of these two segments. Its edges should also be cut at an angle of 45 degrees.
	The second step is the formation of a do-it-yourself metal swing structure on bearings. We need two pieces 5 centimeters long from a pipe with a diameter of 90 millimeters. Bearings are inserted into them, after which they are scalded for fixing. On the other hand, for additional fixation, a small piece of metal is welded over the pipe. A piece of pipe with a diameter of 27 millimeters will be inserted into the bearings.
	Two plates are welded to a 27 mm pipe - this will be fasteners for carabiners. The bearing structure itself is fixed on the crossbar with the help of two pieces of metal. They are welded on the sides of the pipe into which they are inserted into the bearings. Important - before starting the assembly of this part, apply grease to the bearing and periodically moisten it with water. If this is not done, then the material will heat up from welding, the steel will expand and the structure will be damaged.
	After the assembly of the frame is over, it is necessary to dig two holes under it, insert the ends of the pipe there and carefully concrete everything. After the concrete has dried, it is necessary to weld stabilizing slopes from the remains of the pipes.
	A frame is welded under the seat of a garden metal swing from a prepared profile pipe. We use a welding machine. At the edges we fasten the eye nuts (marked with green dots).
	We fasten the carabiners to the eye nuts and connect everything with a steel chain.

How to make metal swing seats

Such double swings from a profile pipe can often be found on playgrounds. First, a few words about the advantages and disadvantages.

Large metal outdoor swing

Advantages:

strength is the most important advantage of such a swing. Stiffeners greatly increase the bending resistance of the structure;
profitability - profile pipes easy to manufacture, which helps to significantly reduce the cost of all materials;
durability.

Flaws:

careful care - if you do not galvanize the profile pipes and do not cover them protective compounds, then after a while rust will appear;
the complexity of bending pipes - this may require additional equipment.

How to weld a frame for a swing made of metal with your own hands to the country, prepare the foundation and hang the seats, we have repeatedly told, so now we will tell you which seat is suitable for such a design and its dimensions.

The following parts are needed: 3x1600m; 3x880mm; 2x200mm; 5x500mm. More details on the drawing.

A long segment of 1600 mm is installed, 3 short ones of 500 mm each are welded to it - the letter Sh is obtained. Another long segment is welded from the free ends. The back is formed in the same way. Everything is fixed with corners along the edges of each part of the structure and welded together at an angle of 90 degrees. Two pieces of board are attached to the structure with bolts.

To make the back more comfortable for sitting, you need to set it at an angle of 115 degrees. To do this, you need to make an appropriate section at the ends of 880 mm segments for the back.

How to make a garden swing frame - video

To independently create a garden swing frame from a professional pipe, we recommend that you follow the algorithm of actions, as in the video below.

Decorating and caring for metal swings

In order for the swing from the pipes that you made with your own hands to last as long as possible, we recommend that you pre-decorate them and, after every six months or a year, tint them with special paint for metal.

Here's what else you can cover the metal with:

rust solvent;
paint-enamel for metal;
primer for surface treatment;
paint with the addition of metal powder (yellow).

After the building is completed, you can decorate the structure:

Sew seat covers. For them, a dense fabric that is not afraid of contact with moisture is suitable.
Paint the side racks with patterns or drawings. To do this, you need a stencil with patterns or figures, paint for metal and a brush (or sponge). Attach the stencil to the walls. Take a sponge and wet it with paint. Blot the stencil and remove it. Repeat the procedure several times.
Decorate the area next to a homemade iron swing for the street. Plant flowers, build a small decorative fence, arrange sculptures.

How to choose a metal swing

When buying a metal swing for giving in a store, you should pay attention to:

size and dimensions. As a rule, the swing has a width of 2-2.5, which is universal and allows you to easily install it on any type of site. If you need unique dimensions, it is best to make to order.
Manufacturing material. Decide in advance what kind of material you want to see. The classic version is made of metal and wood, but there are also modern materials, such as high-strength plastic, steel bars.
Price. This is an important factor, since on the market you can find absolutely any model for a different budget.

We offer to consider several models of single and double metal swings, which are now popular on the market:

Price	Manufacturer	Main pros and features
8 990 rub	China	1.9x1.13x1.8m	up to 300 kg	● double swing; ● soft seat; ● fabric canopy.
3 710r	Russia	1.37×1.42×1.8m	up to 90 kg	● single swing; ● product bases are installed in concrete; ● wooden seat with chain attachment.
6 890 rub	Russia	3x1.2m	up to 100 kg	● double swing; ● wooden seat; ● fastening - steel chain; ● without foundation
12 990 rub	Russia	2.9x1.55x2m	up to 250kg in total	● double swing; ● seat material - plastic; ● suitable for children 3-10 years old; ● production material - steel

In conclusion, I would like to say that regardless of whether you want to assemble a metal swing yourself or purchase a finished product, you need to look first of all at their quality and ease of use, choose only the best. We hope that now you know how to do it. Good luck!

Today there are a huge number of accessories designed for the garden. One of them is a garden swing, which will not only become an attractive element of landscape design, but also a very useful design. Both children and adults love to swing on a swing, because this activity calms, cheers up and has a positive effect on human health.

What swing is better for giving?

For the construction of a swing, only 3 types of materials are used - wood, metal and plastic. Each person decides for himself which one to use in the production of a swing for his own garden. To do this, it is necessary to study the advantages and disadvantages of different models.

The main features of a wooden swing

practicality and versatility . Wood is a material from which you can build not only the usual single swing, but also cozy sofas with several seats;
ecological cleanliness . The tree has a natural origin, so the material is absolutely safe for human health;
harmony with the landscape . A swing made of wood fits perfectly into any garden design. This advantage favorably distinguishes structures from metal analogues, which require appropriate design of the entire site;
safety . Wood is considered a fairly soft material, which greatly reduces the number of injuries. This is especially important if children will swing on the swing;
ease of installation . Do-it-yourself wood swings can be made by absolutely anyone who is at least a little familiar with construction work;
economy . The cash costs will not be large, since the material itself is inexpensive.

Characteristics of a metal swing

durability - this is perhaps the main advantage of such products. Metal is an eternal material that will not rot or break;
reliability such a swing is undeniable. The material is characterized by hardness and resistance;
practicality . Metal is not afraid of the impact of negative factors environment, he is not afraid of rain, blizzards, or ultraviolet;
low cash costs . When compared with high quality wood, the metal will be cheaper;
variety of models . Swings made of metal can be collapsible, welded or forged. Each consumer can always choose suitable option specifically for your site;
metal swing able to decorate original view any plot or garden , however, the designs require appropriate stylistic design, otherwise they will not look very harmonious;
metal garden swing you can do it yourself , but this will require the appropriate skills and abilities.

Metal swings have many positive characteristics, but they also have some disadvantages. For example, the dense structure and hardness of the material is good, but only on the one hand, on the other hand, the possibility of receiving various blows and injuries increases significantly. In order for the metal not to rust, it is necessary to periodically cover it with a layer of special paint. In addition, many people believe that metal swings are inferior to wooden ones in terms of their aesthetic features.

Pros and cons of plastic swings

As for the plastic swing, experts find in them more minuses than pluses. Such children's swings for giving are distinguished by their low cost and a variety of colors. Among the disadvantages are:

plastic structures make all the design of the garden plot cheaper;
such swings are suitable only for kids, but teenagers and adults will not be able to use them;
harmful fumes - this is perhaps the most significant disadvantage of the material. In hot weather, the plastic heats up and releases toxic substances into the air, which can have a negative impact on the health of children. For this reason, it is better to refuse plastic structures altogether.

Types of garden swing

In addition to classification by material, garden swings can be conditionally divided according to the method of fastening the moving part of the product:

horizontal swing - such models are probably familiar to every person since childhood. The structures are long crossbars that have a fulcrum in the middle. In order to swing on such a swing, you need two kids with approximately the same weight;

swing with vertical suspension intended for individual use. Among such structures there are many different types: from simple "bungee" to solid original sofas and benches.

Swings also differ in location, and they can be placed either as part of a whole play complex for children, or stand or are suspended separately.

Having shown imagination, you can combine these two features as you like, as a result, amazing designs are obtained. For example, sofas suspended on chains, as well as circular swings resembling gazebos, are especially popular today.

No less important is the classification by size:

product for the whole family . As a rule, they look like a bench with a comfortable high back. Several people can swing on such a swing at the same time;
children's products with obligatory strap. Such swings can be different: include a seat and suspension or have seats in the form of chairs, etc.;
portable models are convenient and mobile, they can be located at will where it is necessary.

How to make a wooden swing with your own hands?

If desired, a wooden swing can be made with your own hands. It is necessary to decide in advance on the material, design and purpose. In order to decide which appearance will have a product, you can see on the Internet a photo of a swing made of wood.

For work you will need:

wooden bars 100x100 or 50x100 mm. It does not matter if the design turns out to be massive, but there is no doubt about its strength;
boards needed to build the seat. The footage of wooden parts is calculated in accordance with the drawing of a wooden swing;
a chain or strong ropes and a carabiner;
mortar from concrete;
nails and screws;
metal corners.

Scheme of the design of a wooden swing

Of the tools you will need a hacksaw, a hammer, a drill, a tape measure and a screwdriver. After everything is prepared, you can proceed to the main work process, which consists of the following steps:

Production of a bearing support

Initially, a lower frame is constructed, on which vertical bars are fixed. The dimensions of the bars are set in accordance with the dimensions of the seat of the future design. All these measurements are recorded in the drawing of a wooden swing. The following dimensions will be the most optimal: depth - 60 cm and length - 180 cm. The frame must necessarily be slightly wider than the seat, by about 50 cm. This condition is necessary for better stability and reliability of the entire structure.

After all the materials are measured and prepared, you can begin to fasten the bars with metal corners. When making and installing garden swings made of wood with your own hands, it is necessary to take into account the type of surface on which the structure will stand. If the swing is mounted on open ground without asphalt and concrete, then the bars from which the lower frame is made must be covered with bitumen. This composition will reliably protect the wood from decay.

'L' - shaped swing design

At the upper points, the side supports in the form of isosceles triangles are connected by a crossbar, to which the seat is suspended. We lay out the lower part of the support, the swing platform. The side supports are poured into pre-prepared pits at an angle to each other. concrete mortar Cross bars are installed. The ends of the bars are treated with resin or bituminous varnish. The crossbars are fixed with metal corners on self-tapping screws. A crossbar is installed between the side "L" - shaped racks and attached to them with large nails through clamps support structure ready

After the frame is ready for it, vertical bars are mounted, which will play the role of supporting pillars. Installation is carried out using self-tapping screws and metal corners. In the end, you will get a pair of triangles, a horizontal crossbar should be fixed on their vertices.

seat manufacturing

First you need to assemble a frame from the bars. In total, you will need two such frames: one for the seat, the second for the back. Plywood or slats are attached to these frames - it all depends on which option suits you best. Sitting connects to a back also corners.

Experts recommend leaving an angle of 120 degrees between the seat and the back - it is this slope that will be optimal and most comfortable for sitting. Another element for additional comfort will be armrests, but they are not required.

Seat construction diagram Swing seat mounting options Wooden seat

Fastening

Hooks or staples are attached to the top bar. A chain or cable is threaded through the holes in them. Their length is calculated so that a person sitting on a swing can reach the ground with his socks.

After that, the seat is attached. If desired, the design is complemented by an awning. To do this, build a frame of bars, and then pull any waterproof fabric over it.

All joints are fixed with metal corners. Powerful screws are screwed into the crossbar for attaching chains. Lastly, a seat is attached to the crossbar. Ready-made swing for a summer cottage

The wooden seat will be hard, so it is recommended to put a couple of pillows on it for comfort. For long-term use of such accessories, it is better to make covers that can be updated or removed at any time in order to clean them.

If you were worried about the question of how to make a reliable wooden swing with your own hands, then you already know the answer.

Video instruction

How to make a metal swing

Garden swings made of metal can be made with your own hands, without resorting to the help of specialists. For this you will need the following materials:

9 metal pipes with the same diameter;
8 corners;
two metal arcs with a diameter of 16 mm and a length of 25 cm;
2 wooden elements;
a couple of pieces of furniture foam rubber and 2 zippers;
cable.

Of the tools you will need a welding machine, as well as paint for metal.

Do-it-yourself metal swing - diagram

Stages of making a swing:

Preparatory work. This stage is very important, because it is at this moment that all calculations are carried out, and then a drawing of a metal swing is created.
Support manufacturing. Based on the calculations, a drawing is created that will help you make a garden swing from metal with your own hands. Pipes are prepared for welding: rust is removed from them, measured desired length, and on both sides at the joints at an angle of 45 degrees, a chamfer is removed.

Based on the planned swing scheme, it is necessary to weld the pipes. When the support is ready, arcs are attached to the upper part, on which the swing will then be mounted. The design is covered with a special paint for metal.

Poles are mounted in the ground. There are 2 bearings on the crossbar. The grooves in which the crossbar lies.

We must not forget that the practicality and aesthetic appearance of the future product will depend on the professionalism of the welder. For this reason, you should not start work if you are not confident in your abilities, entrust this matter to specialists.

Creating a seat. Segments of a metal corner are welded according to the previously planned scheme of a garden swing. The seat inserts are sawn from a wooden sheet, and then they are inserted into ready-made metal rectangles. For sitting, you can sew soft mattresses that will become a comfortable addition to the whole structure.

Seat parameters Back parameters Required places for welding metal parts Finished seat structure

Installation of swings on supports. For reliability, either special fasteners or a strong rope should be used. It is important to fasten the rope with high quality so that it stays in one place, this is done with the help of fasteners.

Mounting the seat on a support prepared in advance Mounting on a chain

Construction installation. It is best if the swing is under a canopy or in a shady place. The metal structure will be stationary, since its weight does not allow the swing to be moved.

Features of the manufacture of children's swings in the country

When building a structure that is intended for children, some important nuances should be taken into account:

the swing should be as strong and stable as possible;
without fail, seat belts and special fences must be present on the swing for children;
when making a swing, one should build on the height and weight of the child;
it is very important that the baby has the opportunity to reach the ground with his socks and get up on his own;
all materials that were used to create the structure must be environmentally friendly, safe and hygienic.

All these conditions must be taken into account when building a children's swing for a summer cottage with your own hands, because only in this case you can be completely sure of the safety of your child.

How to make a swing out of tires?

Swings can be made from wood or metal, however, if you want to simplify the task using improvised materials for this, ordinary tires are fine. You can fix such a product on a tree branch or place it near any body of water.

The advantages of such a design include ease of manufacture, cost-effectiveness, as well as new sensations that every person who uses such an invention will feel. In addition, to make a garden swing from tires with your own hands, you will not need any drawings and diagrams.

Stages of making a swing:

First you need to install two pillars, which can be wooden or metal. It is very important that the posts are strong enough to withstand all expected loads.
A crossbar is mounted in the upper part of the bars, and bolts with rings cut into it, into which a rope or chain is threaded.
At the bottom, the rope will be attached directly to the tire itself.

Take old tire without serious damage Wash the tire inside and out thoroughly with a cleaning agent Obtain three medium diameter U-bolts Drill six holes (two evenly spaced) for the selected fasteners Bolt holes Check in advance that the bolt holes are drilled correctly Paint the tire spray paint desired shade and let it dry properly Now put the bolts in the holes And fasten with washers from the inside The result is this design For the top of the swing you will need a strong chain with fasteners To create robust design you will need four U-mounts Each of the bolts in the tire needs to be attached with a chain mount. On the other side, connect the chains with one mount. Fix the two ends of a small chain intended for attaching a carabiner in the same place. You can hang the swing in any place convenient for you!

When creating a swing from a tire, it is necessary to take into account the mass of each element, since in the case of using wooden poles their tensile strength is important. In general, this design is more suitable for adults or older children, but not for babies. For greater reliability, it is recommended to use not a rope, but a metal chain as fasteners.

Now you know how to make a garden swing with your own hands, it remains only to choose the most suitable design, materials, and you can get to work.

Swings have always been in great demand. Yes, this is understandable, because children and adults love to ride them very much. In the article we will tell you how to make them in the country, consider various materials(metal, wood), as well as demonstrate photo and video instructions.

Today there are many constructive variations of these structures. We break them down into 3 categories:

Baby. This group includes a swing like a chair with pendants and original boats. The frame is always made in accordance with the safety scheme. For very young children, seat belts should be provided.

Family. Most often they are massive structures like a bench with a large back. On such structures the whole family can fit at once. They are fixed on a U-shaped frame, using cables or strong chains. If a roof is made over them, then you can swing even when it rains.
Mobile - easy and quick to carry, as well as install in convenient location, for example, on the veranda, in the gazebo or house.

Diversity

The hammock type of structures is hung on a crossbar, for example, on a tree. This design allows you to soar above the ground. They will appeal to people who are passionate about reading books. They can withstand weight up to 200 kg.
Suspended is a seat with several ropes attached to the sides. Today they are made light, comfortable and durable. The sizes and shapes of such structures are different.
Single - these are all variations that do not need additional crossbars. Such structures can be quickly installed anywhere. They are made from a wide variety of materials.
Swing chairs can accommodate two adults and one child. They can even be placed in a room, because they have only one point on which they are attached. They are made from a special metal alloy. Outwardly, the sun loungers are airy, but in fact they are very durable.

To do metal constructions, you need to prepare such a set of tools and materials:

Welding machine with electrodes.
Container for mixing solution.
File / skin for metal.
Ingredients for mixing the solution: water, cement, crushed stone, sand.
Bulgarian for cutting metal elements.
Fasteners: bolts and nuts.
Bolt wrenches.
Metal pipes.
Shovel.

First, cut the pipes:

Side racks 2 m long - 2 pcs.
Crossbar 1.5–2 m long - 1 pc.
For the base, 2 pipes on each side (arbitrary length).

After cutting the pipes, remove the burrs on them. This can be done with a sandpaper for metal / a file. The pipes forming the base of such a structure must be welded at an angle of 45º, as shown in the diagram. Then weld the crossbar at right angles to the uprights.

Dig 2 trenches with a depth of 80 cm and a width corresponding to the resulting tripod in our case. The distance between them should correspond to the width of the crossbar. Supports (tripods) will be inserted into these trenches. Before as supporting pillars will be laid in trenches, make a sand cushion 10-20 cm, compact the sand. Set up the tripods and fill them with concrete. It must be done on the basis of a ratio of 1: 2: 1 - cement - sand - crushed stone. Add water to this mixture. You should get a homogeneous, not too liquid mass.

The concrete should cure for a week.

After that, hooks can be welded to the crossbar, on which the seat will be fixed on cables / metal beams. Weld the seat to the metal beams, fix the seat. The finished structure can be painted.

Consider technological sequence manufacturing wooden structure on which several children can sit. Dimensions can be reduced / increased if necessary. Pine, spruce or birch wood can be used as starting material. So, you will need:

boards with a section of 100 × 25 mm, length 2.5 m - 15 pcs.;
board with a section of 150 × 50 mm, length 2 m - 1 pc.;
self-tapping screws 52 × 3.5 mm - 250 pcs.;
carbine - 6 pcs.;
welded chain 5 mm thick, length equal to height;
galvanized screws: 2 pcs. - 12 × 100 mm and 2 pcs. – 12×80 mm.

When choosing screws, pay attention to color. If you choose them to match the wood, then they will be invisible on the finished structure, and to give a special effect, it is better to choose self-tapping screws in contrast.

From the tools you need to stock up:

square;
drill with a set of drills;
tape measure;
circular saw;
pencil;
planer;
hacksaw;
hammer.

Following a plan makes it easier to get the job done right. Therefore, before starting to make a swing, prepare its project.

If you find it difficult to decide, then check out the drawings and diagrams at the end of the article. Remember that the design for children and adults is different.

Make blanks of 1.5 m, cut at an angle of 90º. For sitting, use a board having a thickness of 20 mm. In this case, the thickness of the board for the back can be in the range of 12–13 mm. For the design we proposed, you need to make a seat, for which you will need 17 planks 50 cm long and 15 planks 45 cm wide.

To prevent wood from cracking when tightening self-tapping screws, pre-drill thin holes in the parts to be joined.

If you want to make a more comfortable back, then make it curly. To do this, you will need to use a board of the largest thickness - 150 × 50 mm. You should have 6 blanks. With a pencil / marker, draw the outline of the shape of the workpiece.

Determine the angle of the backrest. Planks should be fastened with the same pitch. To screw them evenly, fasten the ends on both sides, and then in the middle. To swing more comfortably, make armrests. For these purposes, a beam of any width will fit. One end of it must be screwed to the back frame, and the other to the seat.

Then you can attach the chain to the frame. It is best to do this to the bottom of the armrest, where it connects to the seat. The other end of the chain is attached to the top of the frame base on the back. Secure the chain with nuts and washers. Otherwise, the nut may enter the wood, thereby ruining its integrity. A special element with a ring on one side and a thread on the other should be fixed to the seat frame and to the crossbar.

After, you can connect the rings with a chain. It is better to fix the swing of the bench on the A-shaped rack. For support, it is important to use strong logs or make metal carcass. It all depends on you.

Support manufacturing

The A-stand or support is quite reliable and able to withstand significant loads. For work, you will need the same set of tools as for making a seat, if we are talking about a wooden stand.

Make two identical racks that are the same size. Ultimately, they will be installed at the distance you need, which depends on the width of the seat. Racks / supports are connected by a crossbar.

Accurately calculate the angle of connection of the vertical parts of the racks. At the top, the posts must be securely connected. Over time, they should not begin to diverge. Set the crossbar to 1/3 of the height of the support posts. For these purposes, use metal corners and screws. The crossbar must be installed on racks at the same height.

A single bar is usually installed at the top of the rack, but if you want to strengthen the structure, you can make two bars.

The structure should be installed in the ground. Dig holes up to 80 cm deep. Make a 20 cm gravel bed of sand. Insert the posts and fill them with concrete. To prevent rotting of the racks, they must be insulated before pouring. This can be done by impregnating or wrapping the wood with a waterproofing material, for example, roofing material.

If you are making swings for children, then make them safe. sharp corners eliminate, and sand the wooden elements.

Simple

You have left a wooden pallet after delivery building materials why not use it as a base? Agree that it is not difficult, and it does not cost much! All you need is a pallet, a strong rope and a tree trunk to hang the structure. You can make supports from strong pillars. How to do this will be discussed a little later.

The swing can be made from a single pallet, fixed on the sides with four ropes. Everyone can ride. If you want more coziness, then put a mattress on the pallet and cover it with a sheet, and put a few pillows on top. Now you can start reading in the shade of a tree, in addition, here you can take a break from the midday heat, lie down and even sleep.

If you have 2 pallets at your disposal, then you can create cute designs with a back. To achieve greater aesthetics, pre-clean the parts and sand them, and then fasten and paint (cover with a moisture-resistant varnish) the finished structure. Now your nondescript pallets have turned into very attractive country swing!

"Boards" - this is the most simple idea. On the sides of the board, it is necessary to fix one more board so that the rope frays less, then drill 4 holes, put the ropes into them and tie them into strong knots. You can fix such a structure on a tree or a U-shaped support.

Another idea is with a rope. To do this, 4 grooves should be made in the board: 2 at the end and 2 along the edges closer to the corners. The board can be rectangular or semicircular. Although the grooves are open, the rope still does not jump out. The tension force only fixes the position of the rope, which makes the structure even more reliable.

Do you have an unsuitable snow board? Then use it instead of sitting! Drill holes in it and secure the ropes. Now it remains to hang the finished structure on a reliable support!

Do you have old tires? Do not rush to throw them away, because you can build a wonderful swing for children from them! To do this, you will need a tire and a rope. If you want to create some special shape, improve tire designs, then you will need a sharp cutting tool, for example, a construction knife. You can paint the tire to make it even more fun. For best results, you can draw a model of the structure on paper or mark the cut points on the tire itself. Below are the implementation ideas from tires.

If there are 2 small round logs lying around in your yard, then level them, clean and tie them together strong rope, and then tie with a sea knot to the support.

We select the material

The above-mentioned variations in the manufacture of the simplest swing implied the use of improvised materials. But, if you want to create a more sophisticated design, then you can use the right kind of wood and metal. It can be supplemented with a back and a crossbar placed in front, which will make it possible to secure operation.

The list of materials needed for manufacturing can be something like this:

Larch boards.
Self-tapping screws of different sizes.
Carabiners.
Chain for fastening.
Screws with rings.

To create a design, you will need a typical set of tools. It includes a drill with different sizes of drill bits. A hacksaw and a saw, a planer, a jigsaw, a hammer can be useful. For measurements, you will need a tape measure, a square, chalk, or, perhaps, a pencil, a marker.

It is better that the structures are installed in a shady place, under a roof or a tree. If a canopy is not provided, then in bad weather they must be covered with a protective film.

If you want to create a stable support, then you should definitely dig four pillars into the soil to a depth of about 80 cm. Subsequently, they will need to be concreted, then connect the racks and the crossbar. If you chose metal pipes as racks, then they need to be connected using a welding machine. If you are using wooden poles, then before installing them, the material should be treated with an antiseptic preparation. Connect them with bolts and nuts. To make the seat, prepare 2 frames that will serve as the back and seat. Attach the plywood, and then connect the frames at an angle of 120˚.

Now it is necessary to attach special hooks or staples to the seat, which will allow chains, cable or ropes to be passed through them. In this state, the swing can be suspended from the crossbar. Please note that the feet of a seated person should touch the ground with their toes. In fact, country swings can be very diverse, here, perhaps, it all depends on the power of your imagination.

The main thing is that when creating this garden item, you can ensure its safety, reliability and durability. Add some creativity to the product: decorate it, use it unusual item as a seat.

We mount the fastening mechanism

In order to hang the seat to the crossbar, you need to attach special hooks or brackets to it. If you decide to use cables as a suspension, then you will need clamps. Pull a cable, rope or chain through the holes. It is better to use chains with large links. This is due to the fact that they are more durable, not afraid of bad weather and temperature changes. Chains, among other things, perfectly decorate landscape design.

It is better, of course, that the seat be with a back, while the suspension plays a less important role.

The place where the suspension will be fixed should be especially reinforced. If your seat is wooden, then decorate it with pillows, pull up an awning or put a mattress. All these details will only improve your rest and rest of your children.

Swings are an integral part of leisure. You will never regret the effort spent, because your building will delight the family throughout the summer season!

Have you already worked on the creation of such a design? What ideas have you been able to bring to life? Maybe you had difficulties in the manufacturing process? What helped you deal with them? Write comments to the article, we appreciate your work and experience!

Video

You can see an example of making a wooden swing below:

Photo

Scheme

If you decide to make a swing for a summer residence on your own, then the presented drawings and diagrams will help you with this:

Do-it-yourself wooden swing: this is exactly what will be discussed in this article, on the site "". The shady garden on the backyard and summer cottage will be a great place for family vacation, especially if you make a little effort and make it comfortable with various accessories and small structures, for example, etc. Make do it yourself and place on site wooden swing: photos and drawings, dimensions and the main parameters for construction you can find in this article.

Swing- this is a great way to diversify your leisure time while relaxing in the country

Features of creating a wooden swing for a summer residence: characteristics and types of structures

For creating garden swing three main materials are most commonly used. This list includes wood, plastic and metal. Undoubtedly, each of these materials has its own advantages and disadvantages. But when it comes to do-it-yourself garden swing drawings, you will not find a more practical and convenient raw material than wood.

At wooden swing there is only one drawback, which concerns the operation of any products made of wood. Such structures without the application of appropriate protective measures can be severely affected by the influence of negative environmental factors.

Original swing round shape with soft mattress

These factors include the impact of:

rain;
snow;
direct sunlight;
fungi and mold;
insects;
sudden temperature changes;
decay processes.

DIY you can make different swing and turn your ideas into reality

The benefits of creating a wooden swing with your own hands

Wood has excellent technical and operational characteristics. Thanks to the properties this material, you can create a truly comfortable and beautiful design.

Photo: wicker swings in the form of spheres are quite roomy and comfortable

Features of hand-made from wood:

environmental friendliness. Since wood belongs to materials of natural origin, products made from it are completely safe for human health;
external aesthetics. Designs are able to fit into any, since the main part of the environment is natural materials(stone, wood) and vegetation. Compared with metal products, wooden structures greatly benefit in aesthetic terms and can support the exterior of any country house;

Pillows and blankets will do swing softer and more comfortable

safety. Due to its softness, wood is easy to use and operate, it can reduce the number of injuries. This advantage is most beneficial if you intend to design a children's swing;
simple mounting system. Any person who has the simplest skills in construction and handling wood can be engaged in the construction of a swing;

Canopy over the swing protect from the scorching rays of the sun in the summer

versatility. This type of material lends itself quite easily to various types of processing (grinding, cutting, cutting). Thanks to this, any of the wooden gardens, the photo of which you most like, can be done by you with your own hands without involving specialists in this process. Wood allows you to make single-seat structures or swings with a large capacity, made in the form of sofas.

Adults also do not mind relaxing and relaxing, imposingly swaying on a swing

Note! The cost of purchasing the material is not high. In addition to this, by creating products yourself, you save on the services of craftsmen.

Do-it-yourself garden swing made of wood: photos and drawings, dimensions and modifications

If you have made the decision to creating a swing at their summer cottage on their own, first of all, you should decide on the type of structure you want to install, and determine appropriate place for its placement. To facilitate and speed up the design and preparation phase, use do-it-yourself photo of a swing for a summer residence made of wood, drawings of which there are many on the Internet.

Drawing of a wooden swing optimal size for one person

Varieties of wooden swings

Classification of garden swing quite extensive. In this case, the main types of structures are presented:

family - have a high capacity. The design is based on a long bench, which plays the role of a large seat that can simultaneously accommodate up to 5 people. In most cases, this type of swing is equipped with its own canopy that protects from sunlight and bad weather;

On swing family type can comfortably accommodate 3-5 people

children's - designs can have a significant number of modifications. Most often, the main components of such a product are supports, a small seat and fasteners. It is important at the same time to ensure a full level of safety for the child. For these purposes, the design must provide protective elements to prevent the baby from falling. These elements include a comfortable backrest, handrails on the sides, a partition located in front, seat belts that fix the child inside the seat;

Original made of wood in the shape of a horse

portable - products with compact dimensions and light weight. These characteristics allow not only to move the swing around the site, but also to put it in a car for transportation to another place for the rest. As a rule, the fastening of such products is carried out on a tree branch or on a pre-made support.

Portable swing can be moved to any place on the site, depending on weather conditions

Choosing a place to place a children's swing

Any type of construction that is carried out on the territory of a suburban land plot, begins with the design phase and the selection of an appropriate location.

Note! The principle according to which the choice of a place for construction is carried out applies not only to children's swings made of wood. These requirements apply to other designs as well.

Simple children's swing made using wooden board and rope

As far as possible, a plot with a flat surface should be selected on the backyard territory. It is desirable that this area be sheltered from the sun and precipitation. Ideal place for swing building- an area under a tree where a thick shadow falls. It is allowed to perform installation on a porch protected by a canopy.

All these conditions directly affect the level of operating comfort, since sitting on a swing seat that is hot under the sun is unpleasant and inconvenient. And unhindered exposure to rain can damage the structure.

Placing in the garden children's swing, it is necessary to provide enough space for rocking

It is also worth taking into account the fact that as the sun moves across the sky, the shadow cast by a tree or other objects will move. For installation, you should select a place where the shadow will stand at noon. During this period of the day, the sun has the strongest and most aggressive influence.

Drawings and photos of wooden swings for summer cottages

If we talk about universal designs, then a suspension-type swing mounted on supports A-shape, will become a real object of recreation for the whole family. Moreover, you can install them both on large summer cottages, as well as in small gardens near the house. And the process itself is not expensive in terms of resources of time and effort.

Swing chair design with soft cushion cover

The list of required tools for work should include:

tape measure and pencil (tape measure can be replaced with a measuring tape);
jigsaw mechanical type or electric;
circular saw;
hacksaw;
square for measuring angles (combined type);
truss pins;

DIY swing bed

test square;
saw goats;
thickness gauge and planer;
hammer, screwdriver, clamps, wrenches;
chisel (25 mm);
electric drill with a set of drills (10, 8 and 4.5 mm);
grinding block.

Simple wooden swing for children's outdoor play

Note! Of course, buying a finished design in a store is much easier and faster. But in this case, it is unlikely that it will fully meet all your requirements in terms of design, size, etc. Creating a do-it-yourself garden swing made of wood according to your own drawings will allow you to endow the structure with all the necessary characteristics.

Swing in a quiet corner of the garden allow you to enjoy the aromas of greenery

Building a wooden swing for a garden with your own hands: drawings and selection of materials

On initial stage materials are being prepared to create a garden swing with your own hands, the photo of which you liked the most. Based on the drawings, you can easily understand how many blanks will be required to assemble the structure and what dimensions they should have.

Dimensional table for creating blanks:

Detail in construction	Dimensions of the transverse part of the workpiece, cm	Final length, cm	Required number of blanks, pcs.
Frame part of the structure
Strut (upper)	4.5x14	23	2
Strut (lower)	4.5x14	96	2
Leg	4.5x9	198,7	4
Rigel	4.5x14	210	1
Seat parts
rear pillar	3.5x7	60	2
Bar (reference)	3.5x7	95,5	2
Bar (for seat)	3.5x7	120	2
Armrest	3.5x7	60	2
Back plank	2.5x7	130	2
armrest support	3.5x7	27,5	2
seat bar	2.5x7	128,4	8
Top bar	2.5x9	130	1

In addition, in order to interconnect the above blanks into a single structure, it will be necessary to have fasteners with different parameters.

Additional materials for creating a family or children's suspended wooden swing

The final size of the structure is: 2.1 m (width), 1.235 m (depth) and 1.9 m (height). It is recommended to use impregnated pine as a raw material.

Dimensional table of fasteners:

Helpful advice! Prepare in advance an antiseptic suitable for wood processing, as well as materials for finishing. These points are thought out at the design and planning stage of the future structure.

In addition to fasteners, you will need a number of additional materials: Pair of wooden spacers for the corner area (length 38 cm), sandpaper with a grit level of 120, hooks with a fuse (6 pcs., 5 mm), chain 4.4 m long (link thickness 2 cm).

Do-it-yourself swing with a soft mattress and cozy pillows - perfect place for relax

Drawings of a garden swing: how to make a family structure with your own hands

For swing placement it is recommended to choose the back of the house. Even if your site is fenced off from a noisy street and neighbors, this area will still be the most comfortable and quiet. The backyard in most cases is equipped for relaxation, and you can safely use it for mounting family or children's street wooden swing for giving.

Wooden swing-bench, step 1: design sketch and preparation of parts for assembly

Marking the supporting part of the product

To make the support, you will need to cut the cross beam to the specified size using circular saw. At a distance of 15 cm from each end, marks are made and a straight line is drawn. It should go along all the faces on the beam. This line will be considered as the outer face for the A-shaped support.

Markings for oblique cuts should be applied to the end of the legs. To do this, the square is fastened with rafter pins. One of the pins is mounted on a larger leg (at a distance of 316 mm from the corner), and the other on a smaller one (at a distance of 97 mm from the corner). The leg is laid on the edge and marked with the positions of the square. You should have a bevel for the bottom cut.

Wooden swing bench, step 2: applying glue and fastening the parts together

After that, the positions of the square ruler on the edges of the legs are marked. To do this, you need to move the square in the direction along the leg to align it with the previous position of the ruler. Having outlined the length of the ruler, you can move the square further.

Note! This procedure is carried out until the square is set in length 6 times.

Wooden swing-bench, step 3: fixing the connected parts with self-tapping screws

The last marking line is designed for cross-cutting the beam. These positions are marked with straight lines leading to each of the leg faces. To make a pattern, you need to saw off the material on the side that is not processed.

Cutting the supporting part of the structure

To saw off the material with a hacksaw, you must first put it on the edge and clamp it in the sawhorses. The cutting is carried out strictly according to the markup. Don't forget to control the sides. This is especially true for the upper cut zone. Sometimes it becomes necessary to level the bevel. To do this, it is enough to process the end part of the cut with a planer.

Wooden swing-bench, step 4: mounting the backrest and seat structure

To form the second leg, you need to put the first one to it, joint to joint. After that, all marks along the bevels and length are transferred to the second leg and sawn off according to the markup.

Then both legs are laid on the edge in such a way that the end parts of the vertices are located on different sides. cross beam. The lower part of the legs is moved to the sides until a distance of 1.2 m is formed. The upper part of these parts must necessarily be adjacent to the crossbar. To check the bevels, use a ruler, applying it to the ends. Make adjustments if necessary.

Wooden swing-bench, step 5: attaching the armrests

A distance of 50 cm is measured from the base of the legs and the lower bar is applied. Next, the lines of the legs are transferred, as well as the upper and lower parts of the bar to the corresponding parts. After that, the upper bar is laid on the legs. This must be done so that it is located 15 cm lower than the cross beam runs, and is parallel to the first bar. The markup is carried out in exactly the same way as in the previous version.

After that, the bars are removed, and the markings are combined on the surface. At given points, these elements must be sawn to the required length.

Wooden swing-bench, step 6: hanging the structure

Drawings of a garden swing: assembly of the supporting part

Next stage do-it-yourself swing construction- Check fit. The marking is transferred using a square to the inside of the legs.

Helpful advice! You can use these 4 parts as templates for making the second side frame. It is assembled in the same way.

The template is set at a mark of 22 mm and markings are made between perpendicular lines on inside each of the legs.

Wooden swing bench, step 7: treatment of the product with protective compounds

a nail with a convex head (25x65 mm) is driven in from the outside of the leg;
fitting joints and driving nails into the frame;
the formation of a hole with a drill, the diameter of which is 8 mm. The hole should reach the central part of the end of each bar;
the formation of the mounting hole with a drill, the diameter of which is 4.5 mm. This should be done as deep as possible into the end part of the bars;

Drawing of the supporting part for a wooden garden swing

tightening parts through the mounting hole using square head screws, complete with washers 8x100 mm. You need to do this procedure with all the bars;
placing the cross beam in the appropriate place on the top of the frame;
alignment of the frame edges with perpendicular markings on the transverse beam;
formation of a hole with a diameter of 10 mm in the beam and in both legs;
fixing parts with a bolt with a semicircular head (125x10 mm) and a nut;
checking the angles between the beam and the leg;

A-shaped design - the most reliable in quality swing supports

formation of through holes in the leg with a diameter of 4.5 mm at a level of 30 mm from the bottom of the beam. Fixing parts with screws (65 mm). Similar actions are performed in the upper part of the leg. Only in this case, other screws (38 mm) are used for fastening.

Next, you need to connect the upper bar and the crossbar. The spacer is fixed with a through screw, the size of which is 65 mm. The upper part of this element is fixed to the lower edge of the beam in the end part with a 38 mm screw in a pre-made hole (4.5 mm).

Swing, installed on the terrace - a great place to spend time with family and friends

Making a wooden swing seat

The technology for creating a seat is carried out in stages based on an L-shaped frame made of boards (40-50 mm).

Note! Do-it-yourself drawings of a children's swing made of wood in many ways similar to conventional family-type structures. Only in this case, you can shorten the seat, making the swing single, or add a few safety belts to secure each child in a large seat.

Pallet swing, step 1: cutting pallets to the desired size

Step-by-step instructions for making a seat:

from the boards, 3 frame parts for the bench should be formed. They should be L-shaped. Fixation is carried out with self-tapping screws. To fit frame part under the curve of the spine, use carpentry tools. Thanks to this, you can achieve a comfortable posture for your back while riding;
frame elements should be placed along the length of the bench with the same step. Use a thin board to hold them together. The resulting design will become the basis for creating a bench. The part with the vertical type of placement will be the back, the horizontal one will be the seat;

Pallet swing, step 2: treatment of the wooden seat with a moisture-proof composition and varnishing

the remaining seating area is filled with boards. Pre-drill holes in them to facilitate the process of screwing in screws and prevent cracks. Make sure that the boards are spaced at the same distance and have the same length;
abrade the surface with a grinding tool. Thanks to this, you can eliminate bumps and burrs on the wood;
fasten the armrests.

Pallet swing, step 3: securing the swing with a cable or strong rope

Photo of a wooden swing for the garden and the process of hanging

In order to hang the seat in its side part (approximately in the middle), you should install screws equipped with rings. Two more rings are fixed at the bottom of the crossbar. These elements will be used to connect the support and the swing using hangers. In this case, chains are used.

The connecting elements between the main parts will be carabiners. The length of the hangers is set as desired. Optimal Height to accommodate the bench is 30 cm above the ground.

Drawing of a double swing suspended on metal chains

Helpful advice! Chains can be replaced with a rope or a strong rope. The feasibility of this substitution lies in the fact that the rope or rope creates much less noise than chains. But it is worth remembering that their service life is also reduced compared to metal elements. The rope stretches over time under the influence of weight loads, so periodically you will have to correct the height of the swing.

Swing hanging from a tree with a rope

The final stage of building construction

The next stage of construction will be final. In order to protect the finished structure, swing needs to be treated with varnish. It will provide a smooth surface, preserve the natural beauty of wood and extend the operational life of the product.

Depending on personal wishes, swing you can paint in any of your favorite colors or install a small canopy. Show a little imagination at this stage, and you will be able to create a unique product.

Finished designs can be decorated with pillows, blankets and other decorative elements.

For more comfort, you can put pillows on the bench or a small mattress to reduce the hardness of the landing. Its size should correspond to the size of the seat. Anyone who is familiar with the technology of making upholstery for furniture can be advised to apply these skills when creating a swing. Soften not only the seat, but also the back, as well as the armrests, if they are present in your design. Do not forget that soft upholstery is possible only if the product is located under a roof or canopy.

Wooden and metal parts of the swing must be periodically treated with protective compounds

Photo of a children's swing made of wood and how to create them

Children's design options are much easier to perform, since the requirements for weight loads for them are much lower. On the other hand, safety standards in this case should be strictly observed, since children are extremely mobile and can swing in various ways.

Baby swing from a skateboard, made by hand

Creating a kindergarten swing with your own hands: video and various manufacturing methods

The most popular designs for the garden are hanging type swing. There are several simple methods for creating products for children.

According to the first technology, a wooden seat is used in the form of a wide and thick board. Holes are made in it (a pair on each side) where the rope is threaded. This is done in such a way that the suspension is stretched into one hole, and out of another, located nearby.

Children's swing from a skateboard, step 1: prepare materials and tools

Helpful advice! In order to strengthen the structure, in order to prevent breakage of the board in the area where the holes are located, an additional board with through recesses can be installed under the seat on each side. These holes should be located exactly under those made in the seat. The rope will pass through all paired holes.

Children's swing from a skateboard, step 2: remove the rollers from the board and drill holes in it

The second technology involves the creation of a swing based on a frame-frame made of wood. This element is tied to a crossbar or a tree branch with ropes, and the free space is filled with small but strong boards.

Children's swing from a skateboard, step 3: preparation of wooden blocks of round section for armrests

As a seat for the structure created by the third method, half of the rounded log is used. It should be cut along. This option the seat is considered very durable, but requires careful processing. The surface of the log must be well sanded and polished to get rid of knots and burrs.

Baby swing from a skateboard, step 4: pulling the rope through the holes of the board and armrest bars

The fourth option for creating a structure involves the use of a board as a seat and through metal fasteners. A range of modern stores offer fixing fasteners various forms, so you will have a fairly large selection.

Children's swing from a skateboard, step 5: fastening the created structure to the tree using carabiners

In terms of design children's swing do not impose serious restrictions. To create them, you can use any improvised materials. For example, a rope can be replaced by a chain, a wooden board used as a seat can be replaced by a chair, after removing its legs. Be sure to use bright colors, because the abundance of colors is very popular with children.