Zoning of the space of the premises is often performed by the device of floor coverings with dissimilar materials. The surface of the kitchen area is covered with ceramic tiles, the floor in the dining room or living room adjacent to the kitchen is finished with laminate. The materials belong to completely different groups of facing products, but they perfectly coexist side by side. To decorate the connecting lines between them, there are sills for laminate and tiles, which can divide the space, at the same time making it whole. They frame stair steps, podiums, exits, transitions between rooms from laminate to tiles.
Since it is no longer customary to equip door frames with a threshold, the joints of the floors of neighboring rooms are also joined with an additional profile, hiding the gaps. It does not matter if they are made only with laminate or its combinations with ceramic tiles. Docking lines are straight, curvilinear, complex. Floor surfaces can be in the same horizontal plane, with a slight difference in height. There are many strips, profiles that help hide all the transitions, bumps. They can be found on the shelves of almost any building materials store.
In addition to thresholds, there are other ways of joining inhomogeneous elements. It is impossible to accurately determine their effectiveness, but it is necessary to get to know each other better. The transition from tile to laminate can be done using:
- sealants (foams, pastes, mastics) - they can seal seams of any configuration. It is important to choose a sealant that will have good adhesion to tiles and laminate. The connection is almost permanent. This is both an advantage of the method and its disadvantage. If it is necessary to carry out repair work, you will have to dismantle all the floors entirely. Since sealants tightly grow together with laminated surfaces, tiles. They can only be used with absolutely the same height of both coatings;
- cork compensators are completely new products that are already popular. If the work is done exactly according to the technology, the transition is neat and beautiful. The installation process is quite simple, the compensator is laid with a conventional screwdriver. Preparatory actions take a lot of time, require special care, since the seam must be obtained along the entire length of the same depth and width. No damage to the edges of the coatings is allowed. This is especially true for laminate.
Sealants 
Cork expansion joints Of all the ways, the most convenient option docking of different quality materials is the threshold between the tile and the laminate. A large number of market offers building structures give the floor surface a neat, finished look.
Types of thresholds for laminate and tiles
Classification connecting elements The joining of ceramic tiles and laminate can be performed based on several criteria: materials, purpose, connection methods. The most commonly used raw material is aluminum, plastic, wood, cork, a combination of metal plus rubber are also used. According to its intended purpose, the threshold (this is how even a completely flat element is called) happens:
- traditional, classic, if it is a frame for steps, external corners of the same quality or two different materials. It has the shape of an inner or outer corner. The threshold is usually made of metal, since wood or plastic is not strong enough, stairs need strong profiles. A sufficiently large load from the movement of people and goods falls on the steps, therefore, increased requirements are imposed on the upper coatings;
- edging or leveling - with a small difference in levels for tiles and laminate, the sills are made of metal, equipped with an elastic rubber gasket. It is the rubber layer that compensates for height differences during installation. The result will make itself felt - a fairly flat surface is obtained. If there is a height difference bigger size, it makes sense to choose a solid plastic nut that is suitable for the size of the section;
- decorative overlays that trim the threshold during transitions between rooms. The material is used in the case of joining homogeneous and dissimilar parts. Covers are made from almost any material. If metal is taken, then it can be decorated with a finishing film for the main type of floor, plastic strips are produced in any color, for any texture;
- curvilinear sills - are used when it is necessary to connect dissimilar surfaces with unusual design decision. The joint can turn out to be beautiful, even only when both floor surfaces are laid on the same level. Aluminum is not useful here, since it is not malleable enough, it is impossible to make arbitrary bends. Therefore, durable plastic, cork, is used. It is not easy to set such a threshold, but it looks very beautiful;
- final ones - they are used when they frame the edges of the hallway covering, at the exit to the balcony, loggia, at the podium. The threshold of this type is very often used as a multi-level one when making a connection between a laminate and a ceramic product.
final 
Decorative 
Classical 
Curvilinear 
Docking There remains one more option for dividing the thresholds into types - the method of connection. According to the cross section, the product can be an integral letter H, a flat bar, as well as a composite letter H, consisting of two T-shaped bars. A profile in the form of a solid letter H, laid on its side, is applied by laying the coating on both sides of the plank. Fastening to the floor is carried out with self-tapping screws. In the latter version, one of the strips is installed from the bottom of the seam, leg up. The second one, which has decorative surface, is mounted from above, then connected by the bottom clamp.
Which is better to choose
It is impossible to unequivocally determine which threshold, from which material to choose. For the simple reason that for different conditions connections require their products. According to the constructive solution, the thresholds must be purchased according to the purpose, as well as the intended installation method. Sometimes you need flat pads, corners, sometimes you can’t do without a special profile, sometimes only a cork product can help. If we are talking about the material that is used in the manufacture of thresholds, it is chosen based on the intensity of operation of the floor elements. It should be borne in mind that wooden products, soft plastic moldings are highly susceptible to abrasion, and will quickly cease to serve. metal profiles not suitable for creating complex curved joints. Then you need to opt for plastic products, supplemented with rubber material, designed to warm up, bend, take the desired configuration.
texture, color solutions no problems, everything is much simpler. There are no restrictions here. Plastic sills are available in such a wide range of colors that they can satisfy the needs of any design option decoration of the floor, the general interior of the room. Hardware the question is solved in a different way. Designers came up with special film decorations with high wear resistance. They can be matched to the color, texture of the used laminated, tiled surface.
Installation rules
There are two ways of mounting connecting products: open and closed. The first option is used to install metal elements. They call it open because the caps of the fasteners remain in sight, which subsequently need to be painted with the color of the threshold. Fastening is carried out using ordinary plastic dowels, equipped with self-tapping screws. The metal plane for this has holes made at the factory. With a hidden method of fastening the thresholds, the lower part of the profile is first installed, screwing it to the ceiling with self-tapping screws or planting it on strong glue. On this part of the profile there are special clamps for top bar. The decorative part of the molding snaps into place securely, resulting in a very strong connection.
The floor covering must not completely occupy the gap of the threshold. It is necessary to create an expansion gap that will not allow linear changes in the coating due to temperature changes. Installation steps
Features of the installation of flexible sills
If framing straight thresholds with a corner practically does not cause problems, then the installation of curved joints has some features. They should be considered in more detail. Neither wood nor metal is suitable for these cases because of their inability to bend under any degree. There are two possibilities to connect laminate flooring and tiles: use cork inserts or complex plastic profile. The cork is easy to install, but its arrangement requires thorough, thorough preparation. Cork wood compensator cannot close flaws in uneven trimming of laminate or tile edges. In order for the joint to turn out to be neat and beautiful, the gap between different coatings should be no more than two millimeters.
Abutting surfaces of laminate and tiles are located strictly in the same plane. Their edges are carefully aligned, polished, very precisely adjusted to one another.
If ceramic tiles do not cause problems, then laminated boards are difficult to process, they will require additional labor and time. The result is worth it - high-quality cork joints look very beautiful. 
Mount options
For a curved connection, a plastic molding also needs a curved one. With ready-made radii, it is impossible to purchase one. Usually products are sold that have a relatively small bend. To obtain a rail of the required configuration, it must be softened before installation work. This can be done with a building hair dryer or by simply dipping into hot water. After such actions, the material becomes pliable, easily bends according to the specified parameters. This profile has two parts.
The lower part is attached to the floor along the contour of the seam. It is mounted in parallel with the main cover. On the side of the laminated surface, it is necessary to provide a small clearance to create expansion joint. Since the boards can shrink and expand with changes in temperature. Let it be insignificant, but, in order to avoid deformations, this must be done. The upper part is carefully connected to the mounting clips located on the lower element. In order not to damage the surface of the decorative profile and the floor covering, it is necessary to use not an ordinary hammer, but wooden mallet. Plastic strips are convenient because they can hide a fairly large height difference between the coatings. There are profiles that can bridge the vertical difference between laminate and tile up to 18mm.
Video of installing the threshold between tiles and laminate
In the video you can see how to correctly arrange the joint between the tile and the laminate.
The main question that arises when choosing several floor coverings, is how to install the threshold between the tile and the laminate. Laminate is a very popular and popular type of flooring. It can be used in almost every room. However, in some rooms, for example, in kitchens and hallways, installing a laminate is not the most rational decision. Ceramic tiles are the best. Designers found interesting solution- part of the room is covered with laminate, the second part - with tiles.
What are the sills - straight or transitional?
If you install such an interesting design as a threshold, you can hide the joint between different coatings, compensate for height differences and make the transition from one surface to another in an original way. To date, there are a huge number of a wide variety of thresholds connecting laminate and tile. They differ in shape, connecting seam, material, as well as cost. Depending on the functional purpose, the following categories of sills are distinguished:
- Direct. Thresholds of this type are best suited for, as well as for single-level linoleum joints. They can be used not only between different zones but also between entire rooms.
- Transitional. Thresholds of this category are designed for joining materials with relatively large height differences (up to 20 mm). Thanks to them, you can join tiles with laminate, linoleum or carpet.
- Final. They are used when it is necessary to cover the edge of one of the materials, for example, on a podium element or at the entrance to a balcony.
- Leveling. Today they are the most popular. The installation of such thresholds will allow you to hide small differences in heights between materials (from 3 to 5 mm).
Transitional thresholds deserve special attention, because, in turn, they are classified into several additional subspecies. Allocate angular, used when connecting various floor coverings: tiles and linoleum, tiles and laminate, laminate between rooms. Another type is round thresholds, at which the difference between the levels of the surfaces reaches 20 mm. However, flexible options of complex shape are considered the most popular. In addition to hiding height differences, they prevent water from flowing inside, and also look very stylish and beautiful.
Depending on the connection method, thresholds for laminate and tiles are:
- 1. Profile with through fixation. This is a special strip that covers the joint between the coatings and presses it to the floor. Countersunk head self-tapping screws should be used as the main fixing method. This profile can also be used if cutting wood fiber boards or ceramics is not done very neatly. To seal the edges of the plank, we recommend using silicone hermetic adhesives.
- 2. H-shaped profile. His appearance resembles the letter H laid on its side. The lower part of the profile is brought under installed panels, after which the tile is inserted into the opposite groove and impregnated with glue. As a rule, after this a small gap remains, filled with a special mortar for tiles and sealant from the side of the laminate. Silicone and acrylic compounds are also great for these purposes.
- 3. H-shaped collapsible profile. His distinguishing feature- this is the presence of two T-shaped structures interconnected by legs. This design is installed at the boundary of the gap and fixes it. Upon completion of all installation operations, you will need to insert the decorative upper part into a special clip located at the bottom and snap it into place.
Structures that cover the transition between different floor surfaces are made of various materials. When choosing a nut, be sure to consider the basis on which it is produced. After all, certain materials differ from each other in various parameters, including strength, reliability, durability. The financial component also plays an important role.
Wooden sills are the most in demand and popular, including because they are very beautiful and environmentally friendly. For the transition between ceramic and laminate, it is best to use exactly wooden options. However, they require special care, and also quite whimsical in operation. In addition, they will not work in the case of wavy connections.
Wooden sills are environmentally friendly
Relatively the new kind thresholds in the construction market - plastic. Despite this, they are already very popular, mainly due to the possibility of application in undulating joints. They flex great and hold up great. desired shape while preventing dirt and dust from entering the gap.
Metal sills are another very popular type of structure for hiding the transitions between laminate and tile. They are distinguished by greater strength, reliability and durability compared to other types. They fit perfectly into any interior and are able to emphasize strengths design of the room, as they are presented in a very extensive range of colors. There are also multi-level strips on the market that will hide the height differences between the laminate and the tile.
Aluminum sills are among the most budgetary. This type has found application in straight even joints, while in wavy joints, of course, it cannot be used. The installation process of aluminum thresholds is very simple even for beginners in this business. The main thing is to drill several holes between the materials with and tiles, into which the screws will be inserted. It is on these screws that the threshold will be attached. The process is as simple as possible, does not require time and money.
If it is necessary to perform a wave-like joint, we recommend that you pay attention to flexible rubber sills. Designs made of rubber are unpretentious in maintenance and operation, it is enough just to wipe them with a damp cloth from time to time so that the appearance does not cease to please you. They have found application in hallways and kitchens. It is an indispensable element for decorative design joints. The installation process is somewhat more complicated. However, with big problems you will not encounter. So, flexible thresholds are mounted at the stage of laying the flooring. They must be cut in the same way as the joint. After setting them in the right place, use the help of a building hair dryer to heat and shape the rubber.
Installation features - what you need to know
There are two main methods of general installation - open and hidden. The hidden method is more preferable because of the beautiful aesthetic appearance, since the fasteners are hidden and not visible from the side. However, the hidden method is much more complicated, therefore, most often they resort to the help of open installation.
Any threshold, with the exception of metal, consists of two profiles - working (lower) and decorative (upper). In the case of the open method, the self-tapping screws penetrate through the decorative layer. Naturally, the appearance suffers somewhat at the same time, in addition, self-tapping screws can be felt if you step on them with your foot. In some cases, they protrude quite strongly above the surface, which can cause damage to skin, clothes and even shoes. . Therefore, we recommend that you screw in the screws as much as possible in order to avoid any problems.
If you decide to install laminate thresholds in an open way, you need to mark the holes, which will then be drilled. However, the first step is to prepare the subfloor, including the removal of the foam padding, as well as the application of plywood or hard plastic. The installation of these materials is required to protect the plugs and self-tapping screws used in assembly from loosening.
As you can see, the open method is not particularly difficult to install. In addition, the financial costs are also not the biggest. For this reason, most hide the transitions from one type of surface to another in this way. The disadvantages are obvious to the naked eye - not the most beautiful appearance due to the protruding caps of the self-tapping screws. In addition, the destruction of the holes over time is observed, especially if the threshold between the tile and the laminate is constantly subjected to loads.
Hidden method - installation nuances
Setting thresholds in this way avoids the presence of visible fastener parts. Therefore, in fact, the method is called hidden. The main advantage is the appearance, since self-tapping screws and other fasteners do not distract attention from the nut itself and the transition between the laminate and the tile. A line is preliminarily drawn, in accordance with which the markings for the holes will be located. The distance between them does not matter, only the fact that they are on the same line is important.
Thresholds for laminate with hidden fastening, with due attention and accuracy of work, look just great. In the prepared nut, we install dowels from the end side, in which there is a groove allocated for this. After that, we combine the dowels with the plugs, which must be pre-installed. With the help of a wooden tip and a hammer, carefully hammer the threshold inward. A very crucial moment, since an inaccurate or too strong blow can cause the nut to bend.
There is a threshold with a latch, which is also installed in a hidden way. Its advantage lies in the simplicity and speed of execution of all installation work. To install it, it is only necessary to lay the snap-on profile into the seam, and then cover it with a decorative element from above, hitting exactly all the grooves. The price of such a nut is slightly higher, but the installation proceeds as quickly as possible and without any questions.
Corner connection - how not to harm the tile
In some cases, it is necessary to install a corner for laminate and ceramic tiles, for example, if it is required to install a seam between surfaces of different levels, the difference of which reaches 50 mm. However, this method is not very common. The reason is that the threshold is mounted along the edge of the tile. But given the fact that ceramics is a rather fragile material, an impact drill or puncher can cause irreparable damage to the tile. So corner sills are usually installed using silicone sealants and liquid nails.
Thus, there are a huge number of different thresholds between laminate and tile, which differ from each other in the material from which they are made, texture, colors. The installation process is within the power of absolutely anyone. The main factor here is the choice of the right nut, based on its shape, purpose, and installation method. Laminate thresholds perfectly protect joints from dirt and moisture, increasing the life of floor coverings, and also emphasize the design of the floor, decorating the premises and making them more beautiful and original.
Now designers have a lot of new ones, original ideas for interior design. They combine many different materials, including floor coverings that have a variety of textures and structures. The most favorite combination option is tile and laminate. This is one of the acceptable ways of delimiting living quarters. Interior designers like to apply this method in any one room - in the kitchen, in the hallway, in the living room.
The combination of ceramic tiles with laminate divides the room into zones, visually enlarges it. Usually, tiles are applied to heavily polluted areas, and laminate to cleaner places. But how can you combine these two materials in a room? When joining these floor coverings, a gap is formed, which is not aesthetically pleasing. To cover it, they invented specially designed sills. They are used when the laminate and tiles are laid on the same surface, the height difference should not exceed 10 mm.
When joining laminate and tiles, a flexible threshold is used
Features of joining tiles with laminate
The separation boundary should be in harmony with the general atmosphere of the room and visually and geometrically not differ from the general background of the floor material. Therefore, they use such thresholds to decorate and fasten laminate and tile. Before starting work, be sure to imagine how the floor will look like in the end. It is important that when connecting, the coating is perfectly even, so that the threshold does not stick out, and no one stumbles on it, and the structure serves for a long time.
The main thing before flooring is to perfectly prepare the floor, equip smooth screed. The discrepancy between the tile and the laminate is leveled with a substrate laid under the laminated board. To make the seam even, the coating is cut using a pattern. A small distance must be left between the material so that the coating can expand freely - this will help to avoid deformation. First of all, we lay the tile, let it dry well, lay the laminate. If you do the opposite, then the board will deform due to the ingress of liquid under it. A competent combination of floor coverings will visually enlarge the room and make the atmosphere ultra-modern.
The threshold should harmoniously complement the overall picture of the floor Assigning a threshold between tiles and laminate
Combination of laminated board and ceramic tiles in modern interiors is becoming more and more widely used. These materials look great and are easy to care for. But here you will have to work hard to close the gaps. The boundary between floor coverings can be anywhere - on the threshold between the room and the corridor, the hallway and the kitchen, to separate the living room and kitchen in studio apartments. The gap in this case is decorated with a threshold. The first thing to notice when making a threshold between floor coverings is whether the height will be the same. If there is a difference, a curved joint will be needed, but it can be used as a decoration element.
An important reason for making a gap is to protect this place from dust and debris. Otherwise, at least, it will look ugly, as a maximum, the life of the floor covering will be significantly reduced. If you are making a joint at the border of two rooms, use a low threshold for installation, and if the gap is located between the hallway and the bathroom, install a high wooden threshold.
To join the laminate and tiles you need to use a flexible threshold Junction options
Before you start making out the gap, you need to know what material the sills are made of. Nowadays, several methods are used to cover the joint with or without a threshold.
PVC threshold | Consists of a base and a decoration element. Mainly used for sealing curved joints. |
Metal | Ideal for sealing straight joints, it is also possible for curved ones. A special coating is applied to the material, which increases resistance to various kinds of damage. |
Aluminum | Perfect for sealing joints under doors. Covers seams and evens out imperfections. It can be of several types: with hidden and open fasteners, on an adhesive basis. |
boxed | Possesses the increased sound insulation, protects from blowing. The best option for the bathroom. He has one minus - he is tall (3 cm), you can easily stumble on him. It is important to remember that the norm for the height of the threshold under the doors is 2 cm so that the air masses move freely. |
T-shaped | Outwardly, it looks very beautiful, but the price equivalent is very high - from 600 rubles. per meter, suitable for sealing joints between parquet and tiles, has an adhesive base, and installation is carried out on it. |
Suberic | The most common option, the seam between the laminate and the tile is perfectly even. It costs about 200 rubles. behind running meter, but in everyday life it causes problems - dirt is easily clogged there, which is very problematic to remove. |
PVC transition | Covers major imperfections. First fix the fasteners, then mount the plug. |
Thresholds are made from different materials Types of thresholds for laminate and tiles
To date, the stores offer a wide range of materials for construction and decoration, you can purchase any sills that meet your requirements, including financial ones. They differ in many ways.
There are a lot of sills on the market, choosing the right one is not difficult. Production material
Wooden - made from high-quality breeds and are very expensive. Outwardly look luxurious, suitable for many wood flooring, but it is extremely problematic to take care of us. They need to be polished from time to time, otherwise many flaws will be clearly visible.
Metal (moldings) - much cheaper, strong, have long term operation.
Plastic - cheap, elastic, can be used when making a joint of various floor coverings. A variety of colors, but they quickly become unusable, so they need to be changed often.
The most expensive and high quality thresholds are made of wood. Laminated - their component is a dense fiberboard, texture paper is glued to the surface, a film is applied on top. Drawing can be under a stone, a tree, etc.
Rubber - made from strong artificial rubber or aluminum profile having pieces of rubber. Basically they have the shape of "L" and are mounted on the edge of the steps.
Cork - outwardly they look like a strip made of this material, or it is a wooden lath covered with a cork strip.
Combined - they are mounted between a movable and hard floor covering.
It is not difficult to choose a threshold by color and material Type and structure
Straight lines - used to form a joint between separate sections of the coating, located on the same surface and having the same height.
Corner - are installed along the edges of the steps so as not to slip.
Transitional - suitable for the design of the joint between different coatings, where the unevenness is 1.8 cm.
Leveling.
Final - in their qualities they are similar to corner ones, they are used in the design of joints of coatings that differ in height.
The sills can be of any shape and material. Installation method
Hidden - first, a lower bar is installed between the tile and the laminate, which is fixed on self-tapping screws or glued to the floor. Then a rail is installed on this bar and snapped into place.
Open - with this method, all fasteners remain in sight, but when the need arises, it can be easily disassembled and replaced. Here it is mainly used metal sills because they have mounting holes. Mounted quite simply.
Installation method may vary Which is better to choose
There is no way to specifically answer this question, because the material is selected on the basis of certain conditions. To choose a threshold, you need to know what function it will perform and how to mount it. Situations are different - you may need lining, corners, maybe a special profile, or nothing but cork material will be needed.
If you choose a threshold from a particular material, it is important to know how often it will be used floor element. Wood and plastic sills are the most prone to wear and need to be replaced frequently. Metal products are not suitable for curved joints. In this case the best option, like plastic sills to which rubber material is added, you will not find. They must be heated, be flexible, take the necessary shape.
You need to select the threshold individually Features of the installation of flexible sills
When planning an interior, designers can combine floor coverings, creating original patterns - snakes, paths, bends. Such gaps are difficult to disguise, but there are flexible sills that allow you to beautifully decorate a winding joint and not spoil the overall interior. With straight thresholds, the situation is simple, but with curvilinear ones you will have to tinker. Metal and wooden sills are not suitable for such work, as they are not flexible. There are two options for connecting tiles and laminate - using a cork insert or a complex plastic threshold.
It is easy to work with a cork, but you will have to carefully prepare before installation. Uneven cutting of these floor coverings may affect the quality of the work. In order for the joint to be smooth and have an attractive appearance, the gap between the laminate and the tile should not exceed 2 mm. The surfaces of the coating must be on the same level, the edge carefully aligned, sanded and adjusted to each other. According to experts, laminate is more difficult to process. This will take a lot of effort and time.
Each nut has its own installation method The plastic threshold will also need to be curvilinear. They are commercially available, but have a slight bend. To fit it to the desired shape, it is first softened using a building hair dryer, you can simply lower it into hot water for 20 minutes, the temperature should be 70 degrees. After such procedures, it can be easily bent as you need. The threshold has two parts. The first is fixed to the floor along the joint line. On the side where the laminate is laid, it is imperative to leave a gap for the formation of an expansion joint - this will avoid deformation. The second part is attached to the first with clips.
Plastic threshold can be bent to desired shape How to make a technological joint between tiles and laminate
No matter how beautiful the combination of laminate and tile looks, it is not so easy to realize it, but it is possible. To make a technological joint between these two coatings, there are several options.
- Installing an elastic PVC threshold. The floor coverings are laid so that a small gap is formed between them, where the fixing profile should fit + another 0.5 cm for the expansion joint. In this gap, we make holes for the dowels with a puncher. Then we cut the profile to the desired length and fasten it to the screws. Before installation, we soften it - how to do this is described above. The nozzle is placed in the installed profile, then it snaps into place.
- Installing a flexible metal threshold. First you need to measure what will be the thickness of the tile and laminate together with the substrate and adhesive. The data must be the same. Shape the profile manually. desired length cut off. Its installation is carried out in parallel with the tile flooring. The profile is held together by ceramic adhesive and a wooden surface substrate.
- Installation of an aluminum threshold. Installation is carried out according to several points: the length of the nut is determined by the width of the doorway, then markings are made for the holes, we make them, mount the threshold and fix it with self-tapping screws.
- Adhesive threshold installation. All work is done fairly quickly. We apply a threshold to the junction, draw the borders with a pencil. Then we remove the protective film and fix it along certain boundaries, press it to the base and hold it for several minutes.
- Installation of cork compensator. First of all, we measure the width, length and depth of the gap, select the material according to the data obtained. We mount the compensator in the following way: the height of the floor covering must be the same size, the distance between the laminate and the tile is 1 cm, the edges must be very even and well sanded, we apply sealant to the base between the coating, mount the cork and press it. Cut off the excess, grind the edge.
At the junction of laminate and tiles, it is better to use thresholds Docking laminate and tiles without a threshold
You can make a joint without a threshold. Here you need to apply all the professionalism and skill. The floor covering should not have any irregularities and drops, if they are, then no more than 1-2 mm. The edges are smooth and polished. After the coatings are laid, the gap is filled with a special polymer composition. It has a long service life and does not lose its properties for many years.
Video: Setting different types of thresholds
Beautiful and comfortable laminate is becoming more and more popular. It is durable and does not require much effort in laying, except for the design of joints with other materials. Thresholds for laminate between rooms allow
Quantity Calculator
Connect two different coatings, compensate for small height differences and create an aesthetically pleasing transition.
Nut types
One or another type of threshold is selected depending on the quality of the material, combination with the interior and the shape of the connecting seam. The price category is no less important and must correspond to the quality of the product. Thresholds for laminate are divided into several varieties regarding their functional application:
- Straight, which are ideal for single-level joints of linoleum or tiles with laminate. These can be connections between rooms or between different zones;
- Transitional, connecting materials of different levels, permissible from 3 to 20 mm. Often such a connection is used to combine the laminate with carpet, linoleum or tiles;
- Finishing, used to close the edge of one of the materials, for example, at the thresholds, at the entrance to the balcony or on the podium element;
- Leveling, which are the most in demand, as they hide a small difference in levels, from 3 to 5 mm.
Separately, it is worth mentioning transitional structures. They are further subdivided into several types. The most popular are the corner thresholds, which can be used for different combinations coverings: threshold for laminate between rooms, laminate with tiles or linoleum. Another type is round, also used for several types of multi-level materials. The difference in height is allowed from 10 to 20 mm. The most popular are flexible thresholds of complex shape. They resist water intrusion well. They mask joints near niches and arches, between rooms or different areas of the room.
Flexible designs
Curved or curved seams can be formed with flexible thresholds. They are also able to hide the threshold between tiles and laminate or linoleum in 10-15 mm. An indispensable element of a flexible threshold is the decorative design of joints, often found in the kitchen, when the working area is made in tiles, and the dining room - in the laminate. The basis for the production of flexible thresholds is plastic or rubber.
Laying is done even when installing the flooring. To do this, as shown in the video, they are cut in accordance with the geometry of the joint, set in place and heated with a building hair dryer to create the desired shape. In this case, the bending radius in the cold form is 30 cm, and when heated - 60 cm.
After these actions, the threshold completely fills the gap space - the threshold between the laminate and linoleum. The profile of flexible thresholds with concealed fastening consists of two parts. One is in contact with the subfloor and is equipped with a special groove, the other is a decorative strip, which, after heating, is inserted into the first part of the nut. After cooling, the junction becomes more rigid and reliable.
Mounting technique
Thresholds can be fixed in two ways - open and hidden. The latter is most preferable, since the fasteners are invisible, which improves the aesthetic appearance of the floor covering. The design consists of two profiles - working and decorative. Metal thresholds have a difference, the design of which does not have a lower profile.
An open mount looks less aesthetically pleasing, since the fastening components are mounted through, when the self-tapping screws cut through the decorative layer. To fix the nut in an open way, holes are marked, which are then drilled. But before that, it is necessary to prepare the base: remove the foam pad and put hard plastic or plywood that will protect the screws and plugs inserted into the holes from loosening. Of course, this method is cheaper and easier, but the appearance of the threshold is not the best. In addition, the holes will begin to collapse over time and the nut will no longer stay in place.
Hidden way
The advantage of concealed fastening thresholds, as seen in the photo, is their appearance, since the fasteners are hidden. At the same time, the distance between the fasteners is essentially unimportant, the main thing is that they are located on the same pre-drawn line. The actions are very simple - holes are drilled along the marked line into which plugs are inserted.
We load the dowels into the trimmed nut (there is a special groove at the end of the nut) and combine them with the already installed plugs. With the help of a hammer and a wooden tip, we evenly hammer the nut inward, as the nut can bend. Another method of flush mounting is a snap-on nut. It is much simpler than the above method. It is enough just to lay the snap-on bar, and then install the decorative element.
Gusset
For tiles and laminate, there is a connection method using corner thresholds, when it becomes necessary to arrange a multi-level seam in the form of a step about 50 mm high. Such a threshold is usually installed along the edge of the tile, which creates some installation problems, since the tile is a fragile material. A puncher or drill may damage its edge. The corner threshold is best installed by gluing on liquid nails or silicone.
The nuances of choosing a nut are the color scheme, texture and material. For example, wide sills look better in door frame the same dimensions. The tone of the nut should match the color of the laminate, linoleum or tile, depending on what materials are to be joined. It is also important that the threshold does not create obstacles when walking.
If all the recommendations are followed, the threshold of the correct texture and color will perfectly emphasize the design of the floor, giving it a finished look, and also protect the joint of the floor coverings from moisture and dirt, thereby extending the service life of the materials being joined.
IN modern renovation the arrangement of the floor is provided, with the use of various floor coverings. For example, for each room, if necessary, you need individual approach and an option, to select the floor and cover.
IN different rooms can be different coatings, in certain cases, in the corridor and kitchen, the floor is tiled, and in some rooms, laminate is chosen as the material for the floor. Laying sills for laminate flooring is the last stage of finishing the floor. They perfectly cover all the bumps and mounting surfaces, they will help to mark the boundary of the room.
Based on the fact that the coverage in the rooms is different, a case of uneven level arises, that is, in one of the rooms the floor level will be higher or lower.
If the junction of the materials of the laminate and tiles is not covered, and this looks completely ugly. A good and high-quality threshold for laminate flooring, which has a diverse appearance and method of attachment, will help in this problem.
Terms of use for laminate flooring
For a long service life of the flooring, you need to properly care for the coating and thresholds. Caring for sills is quite simple. They are absolutely not afraid of water, moisture and detergents. The main thing during installation is to do everything carefully so as not to damage or break them.
Appointment of thresholds for laminate
Comfortable and constructive laminate thresholds are used in the final stages of flooring installation. First of all, these elements have an important function:
- Reliably serve to cover the edge, thereby providing safety for relatives and friends.
- The possibilities of the nut are provided in creating an aesthetic completion of a single coating.
- The threshold has warning functions, protects the floor from dirt and water, which without this element can get under the laminate flooring. It is important to understand that if debris or water gets under the laminate, there is a risk of damage, ultimately the material becomes unusable.
- With the help of the threshold, you can hide the unevenness of the laminate, which were formed during the installation process.
Types of thresholds for laminate transitional thresholds
Their main purpose is as an addition in the connection of coatings. In turn, the coating is located at different heights. The height can vary from three millimeters to 20 millimeters.
Helpful information ! Powders of this type are used only when it is necessary to connect tiles and laminate together.
In addition, such an application is necessary for docking these materials with carpet or linoleum, as well as tiles. Straight sills
Such sills are intended for the design and joining of floor coverings located at the same height. For example, in the case in which we connect different types laminate between the room and the corridor, the basis is that the level of connected materials should be one plane.
Corner threshold for laminate
The threshold for this type of laminate is often called a staircase. It is used in those cases in which it is necessary to fix the edges of the floor covering in the areas of steps. The type of such thresholds is made of rubber; this will prevent the sole from slipping from the steps and thresholds.
Nuts
Such sills are used when it is necessary to overlap the edges of one coating on the floor of two, which have different heights. They are also used to decorate raised edges of floors and thresholds, balconies, hallways.
What are laminate sills
The difference between the thresholds from each other lies in the color, size, materials of manufacture, methods of fastening. Thresholds are fixed in two ways: open and closed.
open way simpler, but not with an aesthetic appearance due to the fact that self-tapping screws are visible, with which the thresholds are attached. With the second option, the thresholds have a much more beautiful mount, in addition, they are often used.
The sills are made from different materials:
- Wooden sills. They are the most harmonious. They are mounted using mounting rails. A wonderful option for laminate flooring is wood. But still, you will have to sand it and varnish it.
- Throws from metal. The most durable. They have gained popularity due to their reasonable price. Such sills are made of aluminum, steel, brass, and are used more often. From the outside they are covered with gold, silver and wood.
- Cork sills. The price is the same as for wooden ones - these are very flexible thresholds for laminate. It is this quality that allows them to quickly take the desired shape.
- Plastic sills are the cheapest sills, their quality corresponds to the price. You should not think that such a product will last a long time.
- Quite often, a laminate coating is combined with an MDF profile. This product is cheap, the main disadvantage of which is exposure to moisture.
Selection of thresholds for laminate
Correct selection The threshold for a laminate is determined by the assessment of many factors, among them it would be unreasonable to underestimate the importance functional purposes premises. Since the threshold will be between the tile and the laminate, it will be heavily affected by moisture.
Eg, the threshold between the laminate and the tile is very important to protect against moisture. In this regard, the material from which it is made must be of high quality and resistant to moisture.
The threshold that separates the tile and the laminate must be able to compensate for differences in height due to the fact that the difference in flooring levels cannot be predicted in advance. If we take into account the dimensions that the Quick Step laminate thresholds have, their selection will depend on the space in which these products will be used.
At the present time, a flexible threshold for laminate has become very popular; it is made in the form of a roll. These thresholds are perfect for surface finishes that have a curvilinear shape.
Installation and its features
In all cases, thresholds are used in places where rooms meet, since it is often not always possible to maintain equally directed laminate panels throughout the house. During installation, the nut is cut to length. This length, together with the distance between the skirting boards, must be the same.
note! The threshold mounts flush with the surface of the skirting board.
Even the existing difference between the tile and the laminate of no more than five millimeters will perfectly hide thanks to the wide threshold. And also two planes with different levels are connected to each other.
Conditions for the right choice
- When choosing a threshold for a laminate, pay attention to the color, material and surface texture. Also look at the strength, moisture resistance, and intended purpose of the product.
- Choose the color depending on the coating to be joined or on the match decorative elements.
- Keep an eye on the pricing policy when buying a used sill and floor covering. Don't supplement expensive coverage plastic, its cost is very small and it is of poor quality.
There you are good advice : Make the selection of thresholds only after you decide on the flooring, its color, material.
Installation of thresholds is not at all difficult, you can easily perform it with my own hands. It only requires that you perform the work consistently in this you will be able to help the video - instructions, as well as the photographs that we have provided you. The main thing before choosing a threshold is to decide on the choice of flooring - this is the most important thing. The choice and decision to carry out the work depends only on you.
In any case, you will succeed, the main thing is to act correctly and confidently. Good luck with your work!
