DIY coasters for plates using decoupage technique from Rimma Heavenly. How to make a stand for a decorative plate with your own hands How to make a stand for a decorative plate with your own hands

How to make a simple stand for decorative plates

Every housewife tries to make the kitchen more attractive and beautiful, while she dreams of having decorative elements that her friends do not have. We invite you to please your soul mate and make it for her with your own hands wooden stand under decorative plates. To make it you will need several pieces of pine boards and several hours of free time. We do not specifically give the dimensions of the stand; you must agree on them with the “customer”, and then making calculations and making a drawing of the parts will not result in a breakdown. The stand is simple in design; it has two vertical posts, several horizontal cross-sections of circular cross-section and several shelves. For the product, a board thickness of 25 millimeters is sufficient, from which you will cut out shelves and make round horizontal lintels.

Where to start

Start by agreeing on the sizes. Let the “customer” tell you approximately where he wants to install the stand and how many decorative plates he has. Based on these data, you will determine the height and width of the stand, you will specifically know the distances between the horizontal ties and their number. Now figure out what materials you have and how you can arrange them into a single structure. Pieces of lumber and slats, boards and pieces of plywood, etc. can be used. All selected lumber must be pre-prepared.

Manufacturing of parts

To work you must have an electric plane, manual frezer And Circular Saw or an electric jigsaw. The parts must be finally cleaned with sandpaper of various sizes; the connection is made with self-tapping screws or confirmatories; carpenter's glue may not be used. The load on the parts of the stand is small, you shouldn’t get it dirty and then clean the parts with wood glue; the self-tapping screws will do the job perfectly on their own. Check and adjust power tools, never work with faulty or unsharpened ones. How better tool- the faster and better quality the products are made and the safer it is to work with them. Both factors are so important that not paying attention to them is strictly prohibited by safety regulations.

First, process the boards with an electric plane, the movement of the plane should always be along the grain. Do not rush to remove large thickness of boards at once; it is better to make several passes with a small cutting depth than one pass with a large cutting depth. Our side posts only have curves at the top and bottom; choose the radius of the curves yourself, use any available objects of a suitable diameter for this. If you have time and desire, you can go along the edges with a figured cutter, this will improve the look somewhat. appearance stands. Round cross braces can be made using electric planer. Of course you have some lathe on wood, the stand will look more attractive; by hand you will never be able to make a perfectly round piece from a square piece. But modern designers recommend specifically focusing on handmade decorative elements, this emphasizes the uniqueness of the design and indicates its exclusivity. So the choice is yours, but we advise you to listen to the recommendations of professional designers, and not only when making this particular stand.

Horizontal shelves have a selected profile to support the edges of decorative plates; the profile is selected using a router. The sampling depth should ensure reliable fixation of objects and completely exclude the possibility of their spontaneous sliding. The lower part of the shelf is slightly wider than all the others and has a semicircular profile. You can attach hooks to it, on which decorative items will be hung. wooden spoons and other kitchen utensils. At the top there is a wide jumper that is attached to the wall. It is advisable to connect it with the side vertical posts in the spike/groin. If you don’t want to waste time on such a connection, then use self-tapping screws or confirmations for fixation, just increase their number and diameter.

Assembling the stand

Before starting assembly, be sure to check the dimensions of the parts. Due to the fact that you will be connecting them end-to-end, the length of the horizontal elements must be absolutely the same. How to adjust parts to length? Clamp them with clamps, while aligning them with an even bar on one side. On the opposite side, you need to accurately cut the parts to the shortest length. It is very important that the angle of all cuts is exactly 90°, otherwise gaps will appear at the joints, in addition, the joint itself will not have sufficient strength - the stand will not hold a rectangular shape.

On the vertical posts, mark the installation locations of the horizontal elements; the markings on both posts should be symmetrical. Then fix the parts one by one to one stand, do not rush to tighten them too much at once, let them still have a small backlash. Attach the second one to them in the same way. vertical stand, check the angles again separate elements and only after that tighten the fastening hardware until it stops.

Finishing

Today, products from natural wood, and if so, then you should not hide its structure with paints, for finishing use clear varnishes. Before varnishing, it is necessary to sand off all the pile very carefully, otherwise it may rise while the varnish is drying and the entire product will have to be sanded again. You need to apply varnish at least twice, choose only high-quality varnish. The fact is that wet decorative plates can be placed on the stand, the water will long time located on the lower supports of the plates. Cheap varnish will not withstand such operating conditions and will begin to peel off; you will have to do “unscheduled” repairs, remove the old coating and apply a new one. This is quite long and always unpleasant.

550 rub.

RUB 1,250

RUB 1,300

750 rub.

850 rub.

RUB 1,250

950 rub.

2,000 rub.

RUB 1,500

RUB 1,250

RUB 1,350

RUB 1,450

700 rub

Every person at least once in his life tried to collect a collection of some interesting things, for example, coins, figurines or painted plates, which, among other things, are effective decorative elements. The same coins can be collected in a box, but it is better to display beautiful dishes. If you like to collect something like this and always buy original and unusual things to decorate your home, then you will certainly need a stand for a decorative plate to store them. It’s not at all difficult to make it yourself; the main thing is to strictly follow the recommendations given in this article.

In order for you to get high-quality and reliable stands for decorative plates with your own hands, then first of all prepare the necessary materials:

For the manufacture of side walls, planks 1.5-2 cm thick and 8.5 cm wide are suitable.

Important! Their shape can be rectangular or curved, but in the second case you will need skills in working with wood and special tools.

In addition to the sides, you will also need a base, that is, a shelf, which can be made from thick material, for example, boards 2 cm thick and 6 cm wide.
Rods will be useful for supporting plates, which can be made from cuttings intended for garden tools.

You will need to perform these steps in a clear sequence:

Decide on the size of the shelves. Calculate everything so that their width allows you to mark required amount plates.
Saw off the shelves, make one recess in them in the middle.
Cut out the sides, and also make holes in them for installing shelves and rods.
Sand all the parts until the edges are rounded.
Assemble the structure, not forgetting the board for attaching the shelf to the wall.
Fix it at the level of the highest crossbar, opposite it. Before doing this, make two holes in it to attach the shelves to the wall.

Important! Such walls should be made for each crossbar so that the plates do not rest against a bare wall.

Cover the finished shelf with several layers of high-quality varnish and hang it on the wall.

Important! If you wish, you can decorate the stand with beautiful patterns or carvings.

A rather original and beautiful stand for a plate with your own hands can be made from cardboard and felt. In addition to the basic materials, you will also need a hot glue gun and tape.

Important! The shape of the product directly depends on your imagination; it can be ornate or simple. It's better to draw yourself a sketch on paper to use as a reference.

Perform the work according to the following scheme:

Draw a blank on cardboard, or better yet, transfer it from paper. Its dimensions directly depend on the size of your decorative plate.
Carefully transfer the design onto the felt, then cut out two such blanks.
By using glue gun Glue the felt on both sides of the resulting cardboard blank.
Use ribbon and a hot gun to decorate the edges.
Bend the workpiece in the center and glue a strip of braid corresponding to the length of the product.

It’s so easy to make an unusual but beautiful stand with your own hands, and you don’t need any special knowledge for this.

If you're just starting to collect dishes, you only have one great plate, but you want it to take its place in your kitchen, decorating it and adding some flair to it, then this next idea will definitely appeal to you. Your new DIY decorative plate stand is made from a very ordinary cutting board. Such work will not take more than two hours, but its results will delight you every day.

For work, prepare:

Board. You can take an old one or buy a new one, preferably wooden or bamboo. It should be slightly smaller or larger in size than the plate.
You will also need a wooden strip and a small piece to support the product.
A small piece of plywood or wood to cut out a sharp triangle.
Stain or paint of the desired shade - it is better if it matches the color of the facades, countertops or kitchen apron.
A rag for staining or a brush for painting.
Saw or jigsaw.
Strong hold adhesive.

Follow all steps indicated in these instructions:

Using a jigsaw or saw, shorten the fragment or plank to the required size (according to the width of the board), sand the edges sandpaper, glue it to the bottom of the cutting board.
Cut the support for the stand from a piece of wood so that it is shaped like a sharp triangle with a right angle. Then glue it to the back of the board as well. The angle of inclination of the holder directly depends on the inclination of the hypotenuse of this block.
Paint the workpiece and let it dry.
Decorate the handle of the stand with ribbon or jute rope if you want to hang the board on a hook.

Important! Such a stand can be decorated in an interesting way, for example, aged artificially or burn a design, draw something, cover it with slate paint.

You can make such wonderful stands for your collection of decorative plates from scrap materials without leaving your home.

Decorative ceramic plates on the wall are now gaining new popularity. This kind of decor is becoming more and more common among designers and in fashionable interiors!

How to beautifully place and hang souvenir plates on the wall:

5 ready-made layouts and rules for beautiful hanging!
6 ways to make a mount for ceramic plates DIY or how to use wall holders and hooks

You won’t need much effort to attach such a souvenir to the walls, but a spectacular and original result is guaranteed!

But no matter which of these decorating methods you choose, everyone will then have to complete the following process - attach the plates to the wall. Here, too, there are several methods for securing and attaching plates to the wall:

How to hang a plate on the wall without nails

The simplest fastening method that does not require nails, which does not even require you to know how to drill walls, is to buy it at a stationery store. special double-sided Velcro.

if the plate is small, just stick one piece of Velcro on it and attach it to the wall,
If bigger size- a few on a plate.

Remember that in this method you need to take into account the weight of the plate if you want it to remain intact.

The second method does not require nails:

We glue any base to the plate - it can be a block of wood or a piece of six tin can. There is only one condition: it must be solid, hold its shape and not become limp from the glue.
We are waiting for our base to dry on the plate.
And then we attach the base with the plate with glue directly to the wall.

The base in this case improves the adhesion of the smooth plate to the wall. In addition, many plates are not completely flat, which makes gluing them difficult. That's why they use the base.

What glue is better to use? Liquid nails or cold welding glue work well.

DIY wall plate holder

By using cold welding Glue a ribbon to the back of the plate and use it to hang the plate on a nail. If you don't like how the mount on the back of the plate looks, you can decorate it. Here, of course, you will have to make holes in the wall. But beauty requires sacrifice.

If you don’t have any special cold welding at home, you can use regular superglue.

Glue the ribbon to the plate, and stick a circle (square, or whatever you prefer) of paper on top to secure the ribbon and make the structure more reliable.

Fastening the plate using electrical tape or adhesive tape

If you have a light ceramic plate and have electrical tape or adhesive tape on hand, you can use that too. When you attach the tape, keep in mind that its end must be quite long in order to glue it generously along the entire length, in order to avoid the tape slipping out from under the tape.

Fastening with paper clip, wire and hairpin

You can also make a circle-mount from a regular olive lid, for example. Or take a wire or a hairpin

You can use a gun with silicone rods. The main thing is to warm it up well and quickly attach the wire or pin to the plate.
In all these ways for best result need with started degreasing the back surface of the plate, you can even scratch it a little so that the adhesive materials do not come off and hold the fasteners securely.

Ready-made hooks for ceramic plates on the wall

You can also use special stand mounts that are attached to the wall, and a plate or several are placed in them, depending on the size of the stand.

There are 2 types of such holders:

metal on a spring basis,
self-adhesive circles with loops.

In stores for handmade products or specialized painting workshops, they sell special self-adhesive circles with loops that can be attached to a plate. Or fastenings of the same type, but requiring the application of superglue to attach to the surface of the plate.

How to choose a purchased wall mount? Only by the weight of the plate: if the plate is massive, then the best option- on a spring, if the plate is small, then take a self-adhesive one.

The process of installing plates to the wall

Before attaching the plates to the wall, we highly recommend making a paper mockup first. This is especially true if you use nails for fastening. Yes, even without nail fastening - if the plates are not glued correctly, it will also leave an unsightly blemish on the wall.

Place the plates on the paper, trace them and cut them out. This will give you the exact diameter of the plate
We lay out the layouts on the wall.
We secure them assembly adhesive tape for painting— it leaves no marks on paint or wallpaper.
We outline with chalk or a pencil, which can be easily removed from the wall.

How to beautifully display a decorative plate

You can place and hang plates on the wall in different ways, and you need to take into account the interior of the room you want to decorate. We offer several ideas to help you make your choice:

Schemes for placing souvenir plates

There are already ready-made diagrams for hanging plates on the wall - look and repeat. Also if you have a large object in the center for example beautiful mirror or a painting, you can decorate it beautifully with the help of plates.

Rules for attaching ceramic plates

Chaotic order

If you like “creative chaos” and don’t like strict lines, then the easiest way is to hang plates different sizes in a chaotic order.

They can be one color scheme or with drawings(nature, for example).
The plates do not have to be round, you can also use oval or square.

Magnets

When we travel, we usually bring magnets for the refrigerator as memories of the cities and countries we visited. But this won’t surprise anyone. IN Lately I began to notice that in souvenir shops you can buy not only magnets and cups, but also plates with images of the sights of the city you are visiting. So you can start bringing them in and hanging them on the wall. This way, you can immerse yourself in pleasant memories without the temptation to eat something from the refrigerator.

"Plate puzzles"

There are special decorative plates, each individual plate shows a part of the design. Thus, by hanging all the plates on the wall, you get one complete picture - "plate puzzles"

Geometry

Those who like orderliness and symmetry can hang plates in lines or geometric shapes . Smooth lines of plates of the same size, or a gradual transition from the smallest plate to the largest. You can make a circle, oval or square from plates around a mirror or picture.

Can form shapes from plates: flower, sun, waves or something more abstract.

Ideas for placing plates in the kitchen and living room

Where would such plates look appropriate? First of all, this is an excellent decor for the kitchen or dining area. Also pay attention to how they look harmonious in the living room, for example above the sofa or near a large mirror. If allowed square meters, then you can also decorate the hallway or the wall in the bathroom with plates.

If you have a couple of free evenings, why not start making crafts for the kitchen and home? After all, with your own hands from improvised, natural and even waste materials you can create a bunch of useful or simply beautiful little things. In this material we presented 50 inspiring photos and 12 super ideas with step-by-step master classes for the production of decorative items, storage accessories, kitchen utensils and more.

Idea 1. Tablet stand made from a cutting board

Watching your favorite TV series on your tablet or peeking at a recipe book while cooking will become easier if you make a special stand for this from... an ordinary cutting board. Making this kitchen craft with your own hands will take no more than two hours, and it will be used every day.

To make a holder for a recipe book or tablet you will need:

You can use an old cutting board or buy a new one (wood is best, but bamboo will work). Its size should not be much larger or smaller than the tablet.
A small wooden plank, or better yet, a piece of molding (this is what will hold the tablet/book).

Another block of wood or plywood from which you can cut a sharp triangle;
Paint or stain in the desired color, for example, to match the countertop, facades or kitchen apron ;
Paint brush or staining rag;
Jigsaw or saw;
Wood glue or any other strong adhesive.

Instructions:

Using a saw or jigsaw, shorten your strip or molding to the right size(the width of the board), sand the edges with sandpaper, then simply glue to the bottom of the board.

Cut a support for a stand from a piece of wood in the form acute triangle with a right angle as in the photo below and glue it too.

The angle of inclination of the holder will depend on the inclination of the hypotenuse of the triangular bar

Paint the entire piece following the paint manufacturer's instructions and leave to dry.

If desired, the handle of the resulting stand can be decorated with jute rope or ribbon. This way, when the stand is not needed, you can hang it on a hook.

Also, the craft can be further decorated - for example, by artificially aging it as in this master class, by drawing inscriptions, by burning a design, or by covering it with slate paint. In the following selection of photos you can get ideas for decorating original cutting boards.

Idea 2. Jute coasters

If your kitchen (or, for example, a country or summer kitchen) is decorated in a rustic, Mediterranean, rustic or marine style, then you will probably like this kitchen craft idea. In just a couple of hours you can make coasters for plates for the whole family and guests with your own hands.

To make one substrate with a diameter of 33 cm you will need:

10 meters of jute rope 1 cm thick (sold in construction and hardware stores);
Hot glue gun;
Scissors.

Instructions:

Just start rolling the rope in a circle, applying glue to small sections one by one and fixing them for a while. Once the mat is formed, cut the end of the rope and glue it down.

Idea 3. Organizer for cutlery and kitchen utensils made from cans

Tin cans cost nothing, but they are durable, easy to clean, and their shape is just right for storing all kinds of spatulas, ladle, forks, spoons and other utensils. If you put in a little effort and creativity, you can make a convenient and cute organizer out of them, which, even if it doesn’t fit into the interior of a city kitchen, will definitely fit in at the dacha. You can also use an organizer made with your own hands from cans to store tools, brushes, felt-tip pens and other small items.

Stand for spoons and forks made from cans

To make such a stand for spoons and forks, you will need:

4 or 6 clean and dried cans, without lids or burrs;
Acrylic paint for metal or enamel paint (it will protect the cans from rust);
Several wood screws and a screwdriver;
Thick nail and hammer;
Furniture handle or leather strap with fittings;
A small wooden plank.

Instructions:

Paint the jars inside and out and let them dry for one day.
If necessary, saw the wood to the desired size, sand it, clean it and finally paint it (not necessarily to match the cans).
Take a nail and a hammer and make a hole for the screw in all the cans.

Tip: To make this process easier and not damage the paint layer, place a small block on the table using a clamp, then wrap the block in felt and only then put a jar on the block (see the picture in the lower left corner in the next photo collage)

Place the cans against the board and align them the way they will be mounted later. Mark the location of the holes on the board with a pencil.
Make small holes in the board where the marks were marked, using a hammer and nail.

Screw a screw into the hole of the first can to attach it to the board. Repeat the procedure with all remaining jars.
Finally, install on the end wooden board furniture handle or leather strap using the same self-tapping screws. Ready!

Here are a few other deco ideas and modifications to the design of cutlery stands made from cans.

Idea 4. Topiary for kitchen or home decor

Topiary is a small decorative tree that decorates a dining room or coffee table, chest of drawers or mantelpiece. And topiary is an excellent addition to a gift, especially if you decorate its crown, say, with candies or flowers. Making such a craft with your own hands does not take much time, does not require the use of expensive materials, and even beginners can do it. Once you master the basic principle, you will be able to create topiary for any occasion, any shape and design. Take a look at our selection of DIY home decor photo ideas, you're sure to find something you'll like!

Kitchen Decor Idea for Halloween

To make this craft you will need:

Base made of polystyrene foam, plastic or floral foam in the shape of a ball or other desired shape;
A trunk (a straight tree branch, a pencil or any other small stick);
Decorative elements for creating a crown: coffee beans, artificial flowers, pine cones, colored beans, etc.;
Decor to disguise the pot filler, for example, moss, pebbles or sisal fiber;
Flower pot;
Filler for a pot that will fix the trunk. For example, it will do cement mortar, still the same polystyrene foam or alabaster (the best option);
Thermal glue in a gun;
If necessary, you will need paint to decorate the trunk, base or pot. The trunk can also be decorated with ribbon or twine.

Basic instructions:

To begin with, it is advisable to paint the base in the color of the crown elements so that possible bald spots are not noticeable. You can also paint the trunk and pot and leave them to dry.
Cut a hole at the base of the crown, a couple of centimeters deep, for the trunk, fill it with glue and secure the trunk.
Take the base of the crown and start gluing the decorative parts one by one. The principle of action at this stage is simple: first, large parts are glued, then medium-sized and, finally, small elements fill in the bald spots. You need to glue the decor quickly, before the glue is absorbed into the base.
Dilute the mixture to fix the trunk in the pot according to the manufacturer's instructions and fill the pot with it, not reaching a couple of centimeters to the edge. Next, insert the barrel, hold it for a while and then leave it to dry for a day.
Disguise the filling of the pot with a decorative “cover” (you can fix it with a little glue).

Idea 5. Serving board-tray

But the idea of an unusual serving board-tray, which, although not a cutting board (intended for displaying food only in dishes), can nevertheless be very functional. For example, it can be used to beautifully serve snacks, drinks (olives, pistachios, nuts, chips, etc.), sauces, honey, sour cream, jam. Thanks to the slate part, while the board is not being used for its intended purpose, it can simply be hung on the wall and used for writing.

To make this DIY kitchen craft you will need:

Wooden board 5 cm thick;
Stain of the desired color (for example, to match the countertop);
Sponge, rag or brush;
Chalkboard paint;
Two furniture handles and wood screws for fastening them;
Jigsaw or saw;
Screwdriver or screwdriver;
Ruler, pencil.

Instructions:

Cut your board to the desired size using a hand/power saw or jigsaw. In this master class, the board is 60 cm long, but you can make it shorter or longer.
Stain your board according to the manufacturer's instructions and let dry.

It's time to paint inner part. To do this, first apply masking tape along the edges of the board to limit the painting area. Next, apply slate paint (in this case, you use paint in a can) and let it dry.

Screw the handles to the edges of the board.

You can replace furniture handles with leather straps, paint the board a bright color, burn a design onto it, or attach two “legs” to the back of it.

Idea 6. Stand for mugs and glasses

If you're the type of person who collects wine corks (either for fun or in the hopes of one day making something useful out of them), then you'll love this craft idea.

To make one mug stand you will need:

8 corks (accordingly, to make a set of 4 stands you will need 32 corks);
A roll of cork board, mat or coaster (for cutting out the base of the coasters);
Hot glue;
Leg-split.

Step 1: Lay out your corks in pairs in a square format as shown in the photo below. Using hot glue, apply a bead of glue between the two corks and press them together for 30 seconds. Repeat the procedure with all other pairs.

Step 2. Cut a square from sheet cork (board, rug) corresponding to the size of the future stand. Next, apply thermal glue on it, wait 15-20 seconds. and glue your blanks.

Step 3: Fill the gaps between the corks with glue and let it dry. For better adhesion of the glue to the corks, you can put some kind of press on the workpiece.

Step 4. Wrap the craft with twine and tie a knot.

Handmade coasters for mugs, glasses and glasses can be beautifully packaged and given to a friend

If desired, the stands can be made round, triangular or hexagonal by cutting off the excess with a knife.

Using the described principle, you can make such a hot stand with your own hands. By the way, an old CD will work as a basis in this case.

Idea 7. Wall panel

Another craft idea for the home and kitchen that you can make with your own hands from wine corks— a wall panel for decorating the interior and storing notes, memorable photos and postcards.

Framed cork panel from Ikea

To work, you will only need a beautiful frame (from a picture or a mirror), paint of the desired color, hot glue and a large pile of corks. Corks can be laid out in a herringbone pattern, in a checkerboard pattern, in even rows, and in other ways that you like. If necessary, for example, if there are not enough corks, they can be cut lengthwise or crosswise. To make the corks easier to cut, you need to soak them in hot water for 10 minutes.

Other interesting ideas manufacturing wall panels with your own hands.

Idea 8. Universal knife holder

Knife holder - very useful device for the kitchen, which helps to maintain working space in order to maintain the sharpness of knife blades longer.

Making a knife holder with your own hands is very easy - just pick up a small vase and fill it tightly with bamboo/wooden skewers, colored beans or... colored spaghetti, as in our master class.

To make a knife stand, prepare:

A container or vase is the height of the blade of your largest knife. The shape of the container can be any, but without any bends;
Spaghetti, lots and lots of spaghetti;
Several large ziplock bags (or just large bags that can be tightly tied in a knot);
Alcohol (for example, vodka);
Liquid food coloring in the desired color (or several colors if you want to make a multi-color filling);
Baking trays;
Aluminum foil or old oilcloth tablecloth;
Paper towels;
Kitchen scissors.

Instructions:

Make sure your container is clean and dry, then fill it tightly with spaghetti. When the container is full, remove the spaghetti and add a couple more bunches of pasta to the pile as a reserve (in case you make up for broken sticks).
Divide the spaghetti evenly between the bags and pour enough alcohol into the bags to wet all the sticks. Next, add 10-40 drops of food coloring to each bag.

Seal or tie your bags, then place them in additional bags to avoid leaks. Slowly shake and turn the bags to mix the coloring into the alcohol and pasta. Next, place the bag on one side and leave for 30 minutes, then turn the bag over again and leave it for another half hour. Continue soaking the spaghetti in this manner (no more than 3 hours) until it reaches the desired shade.
Cover your baking sheet aluminum foil, then layer paper towels(or oilcloth). To protect your hands from staining, it is advisable to wear gloves. Remove the spaghetti from the bags, after draining all the liquid, place them on a baking sheet in a single layer and leave to dry. From time to time, the spaghetti needs to be sorted to dry evenly.

Once your spaghetti is COMPLETELY dry, start placing it in the container.
Shake the filled container and smooth out the spaghetti. Insert your knives to determine the optimal filling density, adding pasta or removing excess if necessary.
Now, using kitchen scissors or other very sharp scissors, trim the spaghetti to required length without removing them from the container (it's best to do this over the sink). It is important that the spaghetti does not exceed the height of the container by more than 2-3 cm, otherwise it will break quickly.

Idea 9. Jars for storing spices and bulk products

Today we will talk about an express technique for making a paper basket that can be used to store small items (keys, stationery), yarn, as well as for unusual presentation of fruits, Easter eggs, bread or pastries for festive table or as a gift.

Even a child can weave such baskets quickly and easily

You will need:

About 15 sheets of thin A3 paper, cut in half lengthwise (this can be printer paper, a full sheet of newspaper, or even baking paper);
A container of suitable size with straight sides (for example, a jam jar);
Glue in stick;
One skewer;
Spray paint (optional).

Instructions:

Starting at one corner, begin to roll the sheet of paper tightly around the skewer to the diagonally opposite corner to create an even and long tube. Once the tube is ready, add a few dabs of glue to the corner of the paper to hold it in place and remove the skewer. Do the same with all the remaining sheets. In this master class, 30 tubes were required to weave 2 baskets.
If necessary (for example, if you used newspaper sheets) or if desired, paint the tubes with acrylic paint.
Take an even number of tubes and connect them together as shown in the photo in the upper left corner. In this master class, for a basket the size of a jam jar, 6 tubes were required, for a larger basket - 8 tubes.

Start braiding: Take one of the outer tubes (which is under the grate) and lay it over the adjacent tube, then pass it under the next tube, then run the tube again over the next tube, etc. Continue weaving by lifting the already entwined tubes vertically (from now on we will call these tubes stands).
When 2-3 cm remains from the first working tube, increase its length. To do this, apply glue to the new tube and insert it into the remaining “tail”. Continue weaving over and over again, adding paper tubes as needed.
Once you have weaved a base of the desired diameter (the same size as the container), place the container on it and begin weaving around it, pulling the stand tubes close to the walls.
Having weaved the basket to the end, remove the jar and carefully wrap the end of the working tube into the weave.
Tuck the ends of the posts inside the weave and trim if necessary. Next, you can spray paint from a can as in our master class.

Idea 11. Wall holder for towels and kitchen utensils

From an ordinary grater you can make such a convenient and beautiful holder for a towel and storage of kitchen utensils or even live or artificial plants.

From a flat grater you can make your own kitchen decor in a country, Provence or shabby chic style

To make a heated towel rail and a tray for small items you will need:

A grater (preferably an old one, but a regular new grater will do, as long as it is metal);
Patina for metal (for artificial aging of the grater);
Small cutting board or just a wooden board;
Wooden die (for the bottom of the grater);
Glue.

Instructions:

Following the manufacturer's instructions, cover the grater with a metal patina, for example, green as in this master class.

Install a wooden bottom in the inside. It must first be cut to the size of the upper part of the grater. As a rule, at the top of the grater there are protrusions from metal handles; it is on them that the bottom will be attached.
Screw the grater to the board using self-tapping screws, after making holes in it with a nail and hammer.
Place the board on the wall near the sink, hang a towel on the handle, and put your spatulas, ladles or flowers inside.

Idea 12. Flower vase

Glass bottles for wine, milk or other drinks are almost ready-made vases that are just waiting to be painted acrylic paints and/or trimmings.

Decorative plates can decorate any home. They are often brought back from long trips as souvenirs. Typically, such products are small works of art or folk art that preserve traditions different countries. After the trip, I want to display the souvenirs I brought in a prominent place so that they remind the owner of the pleasant time spent on vacation. But in order to display such a souvenir on a shelf or under glass in a closet, you need reliable support.

In this article we will look at how to make a stand for a decorative plate with your own hands. It can be created from various materials. These are wire and plywood, pieces of wood and corrugated cardboard. For small specimens, you can use cardboard napkin rolls or even an old plastic bank card. This is not difficult to do, just draw a sketch separately and transfer it to the selected material using a template.

Textured paper stand

This is one of the most simple ways making a stand for a decorative plate with your own hands. It has a beautiful structure, can be in a variety of colors and have all sorts of designs. Choose a material that matches the color scheme of the plate itself. IN as a last resort You can make the product in neutral colors - black or white.

Usually, do-it-yourself stands for decorative plates are made according to a standard drawing. The bottom edge is left smooth or with small legs. Supports for the souvenir are raised in front, which keep the plate from falling. The craft has a bias towards reverse side. This also contributes to the strength of the installation.

So, let's start making. Fold thick paper with a print or a plain version of the material in half. Separately, make a template of the shape described above on cardboard and transfer its contours to paper. Then use scissors to cut out the finished stand. The fold line must be carefully smoothed with your fingers so that the stand does not unfold.

Stand for decorative plate made of cardboard

It’s easy to make a support for a souvenir with your own hands from corrugated cardboard. In any home there is old box from equipment or postal parcels. We will need a very small piece of cardboard for work.

Take a close look at the carved shape of the craft in the photo above. You can vary it in every possible way and come up with the most exquisite openwork forms. The main thing is that the stand stands level on the table surface. It is also important to maintain the angle of inclination for the stability of the product.

You can make such a stand for a decorative plate with your own hands in two ways:

Simply bend the cardboard rectangle in half and smooth the fold line well.
Cut out two identical halves of the craft, and then make slits on opposite sides on the straight edges at the back. One part is inserted into another by pressing the hand from above.

Wooden support

To make such a high-quality stand for a decorative plate with your own hands, you will need to purchase wood, as well as have tools for the work - an electric jigsaw, a jointer and sandpaper. Draw a template for two parts. Their main difference is in the place where the elements of the stand are connected to each other. At the joint you need to cut a hole up to half of the piece of wood, on one piece it is in the front, and on the other it is in the back.

Plane the block with a jointer until flat surface and use the template to cut out the required shape electric jigsaw. All that remains is to thoroughly clean everything with sandpaper several times and cover the craft acrylic varnish.