Do-it-yourself outdoor clothes hanger. DIY wall hanger How to assemble a clothes hanger

floor hanger- a mandatory attribute of any hallway room, whether it is an apartment or Vacation home. Its price depends on the originality of the execution and the quality of the materials. The easiest option is to purchase such a design at the nearest furniture store. But there is another way out of this situation, so as not to overpay - to make a floor clothes hanger with your own hands.

A little theory from the course of physics

To achieve this goal, you will need a little knowledge of physics, as well as improvised materials and tools. Let's start with the first one. The main requirements for a floor hanger are stability and the absence of sharp elements so as not to damage the floor, wall or clothes.

Sustainability is achieved in several ways. If the floor hanger rests on one base, usually in the form of a cross or a circle, then it is necessary to make sure that the center of gravity is as low as possible. This can be done using heavier materials - massive wooden blocks or metal.

If the space of the hallway of the room allows, then it is advisable to install the hanger on two, and even better - on three points of support. In the first case, you need wide bases so that your attribute does not fall on its side, since it is problematic to evenly place clothes. Therefore, if possible, you need to choose a support on three points.

To prevent the base of the floor hanger from scratching the floor, you will need to use materials as a “sole” that will be softer than the floor covering.

Tools and materials

Required Tools

So, here is a list of tools that you will need to make a floor hanger:

cross (curly) screwdriver;
self-tapping screws of different lengths and thicknesses;
sandpaper;
drill;
drills (set);
hacksaw;
axe.

Set of self-tapping screws

You will also need to stock up on the following materials:

dried tree (cherry, sea buckthorn, etc.) or several of these, if the hanger is planned with several support points. You can buy ready-made processed blanks;
bars (more massive, at least 60 cm long, the optimal cut is 7x7 cm);
metal wire (for hooks) or ready-made decorative hooks;
wood glue;
a piece of rubber (or silicone) no more than 3 mm thick.

Wooden blocks for work

Instructions for making a floor hanger with a cross and hooks

First you need to free the trunk of the tree from the bark, as well as coarse knots. Of course, it may seem that with the bark the hanger will look much more natural, but over time it will crumble, and the garbage will spread throughout the living quarters. In addition, the cortex may contain small insects. Yes, and clothes will cling to bumps.

You can get rid of the bark with an ax or a massive knife. Once this task is completed, you will need to go through the rest of the sandpaper first coarse, then fine. After sanding, the surface will become smooth, and the likelihood of catching clothing will be minimized.

The next task is to make the base. As in construction, only that structure will be stable and durable, which is given integrity. Therefore, the base and tripod of the hanger must be one.

The base and tripod of the hanger must be one piece

You should not first make a cross, and then attach the body of the hanger to it from above - such a design will loosen very quickly and may fall out of the base under the weight of the clothes.

Here's a rule to follow - the bottom edge of the tripod should be flush (that is, on the same plane) with the sole of the base.

We proceed to measure the diameter of the barrel. We need it in order to select a bar of the appropriate width. If the bars are wider, then you need to saw off with a hacksaw along to right size.

The standard height of the hanger is in the range of 180-200 cm. For them, you need to make a cross with overhangs from 25 to 35 cm. Therefore, we need 2 bars 60 cm long, which we will cut exactly in the middle to get 4 blanks of 30 cm each.

Now the difficulties begin. Even if you contrive and attach these 4 bars to a round trunk, the structure will be unstable, and after the first fall, due to unevenly hung clothes, it will simply fall apart.

Therefore, we will proceed as follows: put the trunk on the floor and attach the resulting blanks to it from four sides. It will not work to connect them in this form, so we will make inserts in the form of triangular wooden elements on the bars exactly in the part where the body of the hanger is located. Such "triangles" are attached to the bars with self-tapping screws, and also to the tree trunk - in exactly the same way.

To strengthen the structure, in those places where the "triangles" will be attached to the bars-departures and to the trunk, you must first drill holes with a drill with a diameter of 2-3 mm. less than the diameter of the fastener.

If you just screw the screws into the tree, then there is a possibility of cracks that weaken the structure.

After this procedure is completed, it is required to fill the resulting drilled spaces with glue, and only after that start screwing in the screws.

The resulting design of the floor hanger cannot be ideal in terms of stability - it often rolls over from one cross bar to another. To correct this shortcoming, you need to use pieces of rubber that should be glued to the bottom.

In order for the rubber to adhere perfectly to the surface of the wood, it is necessary to go over the surface of the wood with sandpaper and make several scratches in different directions.

The frame is ready, now you need to give the hanger functionality - add hooks for outerwear, which can be remote, that is, located at some distance from the trunk. There is one rule here: the center of gravity of the hanging clothes should not go beyond the cross, otherwise the structure will be unstable and fall.

It does not matter which hooks are used - homemade or decorative, you cannot attach them directly to the trunk, since the floor hanger will quickly become unusable. You can proceed as follows: cut out a square from the existing bars, the length of the sides of which will be several larger diameter trunk used as the body of the hanger. Before attaching the "square" to the top, you must first attach the hooks to it.

Decorative ones are more suitable, since it is very difficult to achieve a beautiful shape from wire. These hooks are attached to the tree, usually with one or two self-tapping screws.

If you have time and some skills in working with wood, then with the help of a chisel you can cut recesses in the squares attached to the top of the floor hanger in order to subsequently “drown” the base of the hook in them. This is a more aesthetic solution than just mounting on self-tapping screws.

After all the hooks are attached, you need a square wooden element connect to the top of the stem. This can be done with one or two screws using the technology described above.

The final stage of work is to give aesthetics to the resulting floor hanger. First of all, you need to close the lower part - the cross with all the fasteners. For this, it is allowed to use fabric, rattan, wooden or plastic slats. The hanger itself can be painted with a protective layer of paint or varnish - both natural color and any other, depending on the color scheme of the room. The layer must be applied at least 2 times.

Making a suit hanger

The scheme of the floor hanger for a suit

The floor hanger for men's suits has a slightly different design and is made of wooden blocks.

You can do it according to the following algorithm:

measure and cut blanks according to a pre-made project;
carefully process and polish them;
make mounting holes in the right places;
assemble the hanger according to the diagram below;
perform finishing;
screw roller wheels to the base or glue rubber gaskets.

25.11.2016 23:54

Not every home has a place for a full-fledged dressing room or a spacious closet. And even if there are any, it does not mean that there is no problem where to put on a bathrobe or handbag - a hanger at hand will never be superfluous.

The most simple, stylish and at the same time cheap idea is to make a hanger from a tree trunk or branch with your own hands. Rustic style is very fashionable today - residents of big cities tend to bring a small piece of wildlife into their interior. And even homeowners living outside the city prefer the atmosphere of country life both outside and inside the house.
Quite a few trade furniture brands turn their design into rustic shapes and textures, so is it worth spending a decent amount to purchase a stylish piece of furniture if you can make it yourself without much effort.
Below you will see hangers created by designers as replicas, trunk imitation natural wood and hangers made from a real tree trunk.

A floor hanger made from a tree trunk in a bedroom or hallway will not only solve the problem of where to hang clothes or accessories, but will also become a nice accent in interior design.
A suitable trunk can be found in the nearest park or forest. It is enough to cut unnecessary branches with secateurs, keeping their "hooks" at the base of the trunk of the desired size. You can peel the trunk from the bark or leave it in its natural form - it all depends on the intended design.
In addition, a wooden hanger can be painted in any color in the interior tones or played in contrast.
For a floor hanger, it’s enough to come up with solid foundation as a weighting agent - it can be heavy wood cut or a prop.

If you managed to find a sufficiently high trunk - the hanger can be installed in the entire height of the ceiling. Here you will need the accuracy of the calculation, but you will not need additional fasteners.

Several small cuts can be cut from a branched tree trunk. Mounted on a wall, on a board, or in an adorable frame, you get a cute and very functional multi-hook hanger. Such a suspension system does not take up space, is very convenient and at the same time has a surprisingly cute decorative effect. A hanger made of wooden hooks from a trunk will come in handy in the bathroom or in the hallway, and, of course, in the kitchen - there are always a lot of little things that need to be hung.

Another interesting way attract the tree trunk to the decoration of the house - it can be hung from the ceiling or in window opening. And this hanging Rustic decor can serve as a support for hangers.

You can use a pretty tree branch to store your favorite jewelry, costume jewelry, or simply decorate it with family photos, homemade hearts, pretty trinkets.

Tree trunk, branches, saw cuts and cuts are often used in decor. Scandinavian interiors or country houses, for example, a chalet - so actively use this rustic decor in the design of such interiors. Rustic accents are also added to cold industrial interiors, loft, simpunk to give the interior a little warm touch.

Below you will see many amazing examples of how to use a tree trunk in interior design and home decoration - DIY tree trunk or branch hanger! Get inspired!

Pay attention - what a zeal for nature among modern designers - we see in the decor: like wood, like moss and even dirty boots ... like)

DIY interior design ideas, interior design ideas, DIY decor ideas - BE INSPIRED!

What can be made from driftwood for the home Shelves showcase racks from stairs

You need to store clothes so that they do not lose their attractiveness, and finding the right outfit is always easy. But what will it be - a few nails driven into the wall, or a stylish and elegant floor hanger? A floor clothes hanger can become not only a functional item, but also a significant element of the interior, adding a touch of a certain style and charm to it.

Pros and cons of floor hangers

The main disadvantage floor structure is its dubious stability, especially for inexpensive products. But if you think in advance what kind of things the future hanger will be used for, you can choose a high-quality, fairly stable and safe model.

Advantages of floor hangers:

Mobility. This part is easy to move to another place. If you have rearranged, repaired, added a new interior element to the room, or vice versa - freed up space from unnecessary things, now the hanger will look more harmonious in another place.

No installation work. When installing a wall hanger, holes in the wall are often required, which damage decorative coating. When dismantling, the holes will be visible, and the wall fragment will have to be repaired. When you no longer need the floor clothes holder, simply hide it in utility room within minutes.

Wide model range. You can choose a floor hanger for any style of interior, for any type of clothing, accessories and even shoes. They differ in size, material of manufacture, external design.

Hanger for clothes floor wooden

A wooden hanger is the most popular option. The tree is strong and durable, therefore, such a hanger will be stable and reliable. On sale there are lacquered and painted products, carved models, as well as the most concise ones, which, by the way, you can do yourself. A wooden clothes stand will be appropriate in many styles - from traditional classics to fashionable ones. loft. Such a hanger will decorate a country-style room, as well as a room in a modern eco-style.

Clothes hanger outdoor metal

Such a hanger has an impressive weight, so there is no doubt about its stability. Most often, metal hangers are made of chrome-plated aluminum, which can be painted in a variety of colors. Separately, it is worth mentioning forged floor hangers. These are products that are not inferior in practical qualities to conventional metal ones, but have enhanced aesthetic properties. Wrought iron hanger is a unique and elegant decoration of your hallway or verandas.

Clothes hanger floor IKEA

Holders from various different materials can be found at IKEA. An IKEA hanger can also be a combination of materials. For example, plastic hangers are unstable due to their low weight, so manufacturers use a hybrid of plastic and metal. Also metal and wooden hangers they are equipped with rubber or plastic tips for hooks (so as not to spoil clothes) and legs (to protect the floor covering).

A huge number of offers of floor clothes hangers suggests: what if you do it yourself? At home, a suit hanger, hangers for outerwear and children's clothes, which are covered with a dust cover, are relevant and practical furniture. Such furniture fits perfectly into the interior, it can be easily moved around the room and apartment.

Clothes on such a hanger wrinkle less than in the closet. It is sometimes called a dressing room, because it allows you to partially unload clothes furniture cabinet and the costumes will be on display. It is also convenient to place children's things on such a design. Cover for a hanger, necessary as protection against dust.

The main difficulty in making with your own hands lies in the processing of surfaces and compliance with dimensions. The conjugation of parts should be maximum, which is not always possible to achieve. by hand. Therefore, in the manufacture of a floor clothes hanger, a combined method should be used: some of the parts and operations will have to be ordered by professionals.

Model selection

According to surveys and sales numbers, the most convenient model of a floor-mounted coat hanger for a suit with a cover is the hanger of the following design:

Dimensions can be changed as you wish. On the upper radius board on the back side, it is desirable to strengthen the hook for children's coat hangers. This will expand the range of applications for the hanger. Do not greatly reduce the thickness, as under load, deflections of parts are possible. Increasing the size within reasonable limits will make the hanger more stable.

You can choose any material: beech, ash, cedar, birch or pine. The latter is the most accessible. It is easier to process and finish. When choosing a material, its moisture content is especially important, since raw wood parts change their geometric shape when dried. Simply put, the part can be twisted or curled up like a propeller. After the model is selected, it is necessary to start preparing materials.

Material selection and preparation

For making at home, it is best to choose pine blanks. They are the most commercially available and easy to handle. Suitable for children's, wardrobe hangers. Do not electrify when covered with a synthetic cover. Their advantages in comparison with other types of wood:

Parts manufacturing

This is the main operation on which the quality depends. finished product. As can be seen from the drawing, you should prepare or buy wooden bars and pine boards. They should not have knots larger than 5 mm. The wood must be dry. Curvature of bars and boards is not allowed. When buying, be sure to take into account those changes that have been made taking into account the specifics and binding to the place. A few tips:

The bars should be with a small margin for processing. When buying, it is better to take two blanks for one part, taking into account possible marriage during work;
Correct geometric shape. This is checked visually. Curved products are immediately visible;
The length is taken with a margin of at least 3 cm. Carefully sawing off 5 mm at home with an electric jigsaw will not work;
Round bars with a diameter of 18 mm will have to be looked for. If there is no such size, then these parts will have to be ordered;
it is desirable to treat finished parts with antiseptic agents before varnishing;
the cover can be made of fabric or other material.

For manufacturing, a minimum set of manual and mechanized tools is required:

Required materials for the manufacture of a dressing room or children's clothes rack:

high-quality pine bars;
self-tapping screws for wood;
wood drills;
varnish for pine wood and stain;
hand carpentry tools;
case.

Modern power tools are equipped with nozzles for suction of sawdust and dust from working area with a vacuum cleaner. At home, this option is very useful.

We now have a set of blanks available. Prepare them in accordance with the dimensions according to the drawing. Symmetrical details compare. They must be the same. cut to size, flat surfaces grind with a grinder. Curvilinear to process with sandpaper. This is the most labor-intensive part of making a suit floor rack hanger. When sawing, it may be found that the wood is damp in the thickness of the massif. In this case, it will be difficult to sand the surfaces. Such parts must be dried at room temperature. Depending on the degree of humidity, the drying process may take several days.

Assembling a dressing room floor suit hanger

This is the final step in the process of making a floor-standing clothes hanger. All parts are made according to the drawing and the conformity of the dimensions is checked, since they are all already indicated on the manufactured parts. You should pay attention to the quality of fasteners. That is, the choice of screws and self-tapping screws. General recommendations choice of screws:

The length should not exceed two thicknesses of the fastened parts. Otherwise, the screw will break through the surface of the second part and everything will be ruined. On pine parts, you do not need to drill a hole in the second fastened part;
Choose the color of the screws in accordance with the color of the material coating;
Self-tapping screws must be used for woodworking. The use of self-tapping screws for metal will significantly reduce the strength of the connection.

An important procedure is marking for drilling holes for fasteners. It is absolutely mandatory to use the hole location designation. You need to mark the place of drilling in such a way that the drill does not go awry. In this case, the strength of the connection of parts will be insufficient.

The diameter of the hole to be drilled for the mounting screws should be half the diameter of the screws themselves. The lack of holes can lead to splitting of wood in the process of screwing the self-tapping screw and the work will be spoiled.

Tips for tightening self-tapping screws with a screwdriver:

Do not screw the screw all the way in. The screwdriver has a lot of torque and can turn the screw through the material.
The final tightening of the fasteners should be done manually with a screwdriver so as not to turn the screw in the hole, since in this case the connection will lose strength.

When the floor hanger is assembled, it is sometimes necessary to varnish the joints with self-tapping screws. Screw heads should be level with the surface. These places should be passed with sandpaper and varnished along with a self-tapping screw head.

Features of children's floor clothes hangers

In addition to size, children's floor hangers are no different from adults. Part thickness for children's version may be reduced. Accordingly, the weight will be less, which will enable the child to move his own children's hanger. The dimensions of the children's floor hanger should be selected taking into account the size of the child's clothes. Designs for girls and boys may vary. It is advisable to provide in the design for the possibility of hanging hangers with clothes on a hanger, followed by covering with a cover. To do this, you can adapt two metal hooks on which hangers will hang. You can place the hooks on the back side of the structure or on the sides.

Other options for floor hangers for suits and clothes

Figured dressing room suit floor clothes hanger

This option looks original, but when making at home, some difficulties may arise with the manufacture of curved parts. It is difficult to maintain symmetry when working with a jigsaw. Both parts must be cut out by combining and fastening the two workpieces. The total thickness should not exceed the cutting depth parameter of the jigsaw. Modern household models designed for a cutting depth of up to 70 mm, and this is quite enough. But this model is not suitable for shirts and blouses. That is, the possibilities of use are limited.

Mobile dressing rack on wheels

Another interesting model on wheels. The top of the design is crowned with regular hangers, which is very convenient for placing a jacket, shirts and blouses. And the pants are convenient to hang on the crossbars. Wheels are a good design find, since it is more convenient to roll a loaded hanger than to carry it. A cover made of film or fabric will conveniently cover the hanger.

This model is produced by IKEA in Russia as a suit and wardrobe floor hanger.

It's easy to make one with your own hands. Required special fasteners. As you can see in the picture, the uprights must be attached to the base with metal screws. During manufacture, it will be necessary to carefully and accurately drill holes for the screws in uprights. This is the only difficulty. Everything else is very easy to manufacture and assemble. The disadvantage is the need to disassemble the structure during transportation. You will have to unscrew the long bolts from the uprights.

Dismountable suit hanger rack floor in rustic style

This hanger is more suitable for a hallway or corridor. You can put shoes under it. In the manufacture of their own hands, this model is a significant difficulty. Need to make holes large diameter in crossed round racks. In general, drilling holes in round parts household tool very difficult. Better not to try. To get around this nasty technological nuance you can take non-circular square racks. Using a special drill, it is quite possible to make holes of the desired diameter in square bars. It is recommended to take a metal crossbar. The wood will bend.

Hanger-rack, hooks on the wall, coat hangers in cabinets are convenient and very optimal attributes in the house. To save space in the hallway, it is advisable to install these interior items instead of shelving. There are many original ideas with which you can create them yourself. Applying personal preference to color scheme, from any material, on any subject (which is close to you and you like, for example, Live nature) and, accordingly, any form. At the same time, the quality and characteristic properties will not yield to the option purchased in the store, if you approach the handwork wisely. The undoubted advantage will be that the hanger in the hallway with your own hands will be distinguished by individuality, originality, and will cost minimal material costs. It is also important that it will be possible to make options that are most suitable for the design of the entire room, which will be in harmony with it. Creating comfort in your home with your own hands is a truly exciting experience.

The main functions that this multifunctional interior item performs:

If there are built-in shelves, you can store items in them, there are also options with shelves for shoes and hats.

In addition, there are models that are used as an element of decor, to decorate and give a certain charm to the interior. They are not used for their intended purpose and are made of fragile, impractical materials.

Materials and tools

The choice of material depends on your imagination and desire. It can be:

You can also use glass, chipboard or cardboard. Each modification has its own advantages and features. Combinations of metal with wood are allowed, silicone coating to avoid slipping.

Since there is different types fabrics, it is advisable to make them yourself or purchase hangers from different materials to maintain their neat appearance. It is important to consider the size (for children, they have smaller parameters).

Tools sufficient for manufacturing: tape measure, hooks (from different raw materials), blowtorch (heater), jigsaw, needle with handle, sandpaper, hand saw, screws, screwdriver, pencil, fitting, screwdriver, measuring instruments, drill, drills , stain, self-tapping screws. In some designs, it is not necessary to use all of the listed tools.

Types of design and construction

There are 2 types of structures: designed to store wardrobe items inside the closet and outside it. The first type includes the so-called “standard model”, that is, a coat hanger with a hook. They fit in the closet, the hook is placed on the crossbar, things hang on hangers. In such a model, a crossbar is made between the sides so that trousers (skirt) can be hung through it, which makes it more multifunctional. Some are made with notches so that clothes with eyelets and straps can be hooked onto them.

The second type includes those on which coats, jackets, raincoats, fur coats are usually left:

Wooden hangers

Wall construction

A wooden structure will fit well into almost any interior. In order to get started, you need to decide what size and height of the hanger you need. Based on this, saw off a suitable piece of board. Use a jigsaw to cut rounded edges with smooth lines, after which they must be sanded with sandpaper, first large, and finally fine grit. Board needs to be processed blowtorch or over a gas burner. Attach the resulting blank to the wall, for this there are 2 tricks:

Attach metal ears on the back side. For fixing with long screws in fastener drill holes;
Fasten the workpiece immediately to the wall by drilling through holes.

The final step is to secure the hooks with screws.

If you want to make the wall hanger more spacious and fit more things, then triple hooks should be chosen. Antique made will look unusual and beautiful.

floor structure

The natural pattern present on the wood, thanks to the stain, will acquire clearer contours. Glue the rubber to the bottom part, made by yourself, so that it does not slip and scratch the parquet.

From a copper pipe

Copper products are always relevant and have a decent look. To do the work yourself you will need: copper pipes: 60 cm - 4 pcs.; 150 cm - 2 pcs.; 90 cm - 1 pc.; copper tees - 2 pcs.; epoxy adhesive; copper corners - 2 pcs.

To make the base, you need to connect 2 copper pipes (60 cm) with epoxy glue using a tee. Do the same for 2 other pipes of the same size.

Attach 2 corners to the pipe (90 cm) (later it will act as a crossbar on which you need to hang clothes). The next step is to insert 2 pipes (150 cm) into the tees and connect the upper part of the pipes to the corners.

After the glue dries, the product can be used for its intended purpose. Let's also add wooden stand, fixing legs on it and using it to store shoes.

From leather belts

The belt can serve not only as stylish accessory but also as a piece of furniture. To make a hanger from an old leather belt, you need to cut off its fasteners, giving the ends an oval shape. Then combine the 2 ends of the belt and at a distance of approximately 3-5 cm from the edge, make a hole with an awl. Make a wooden peg with a diameter less than the width of the belt. Fold the belt in half in the form of a loop and fasten it to the wall with a self-tapping screw or an ordinary nail. Glue the peg with reliable glue at the base of the loop (where the nail is located).

You can also make 2 such loops at a symmetrical distance from each other and thread the crossbar into the loops. Clothes can be hung both on the loops themselves, and on pegs or a crossbar. This hanger looks very stylish and you can improve it different ways by adding bright appliqués, embellishments, additional elements etc.

From branches and cuts

The simplest and most financially advantageous model is made from wood branches and trunks. Such a hanger will bring an element of wildlife to the design, give the atmosphere of a country cozy home, the work will not take much time and effort. Materials can be found in the park or forest. With the help of a pruner, it is enough to cut off the extra branches, the remaining ones will act as hooks. A massive wooden cut is suitable as a support for a floor hanger. The bark can be peeled, dyed any color, or left as is. A trunk with branches can be sawn into sections. Next, hang them on the wall on a board or frame. The result is a multifunctional comfortable interior element. The trunk can also be hung near a window or under the ceiling as a support and a kind of crossbar for hangers.

From a pallet

The main subject for such an idea is a wooden pallet. Before proceeding with the manufacture, it is necessary to remove all unnecessary elements (bottom, side wall) with a saw. You will need a piece consisting of 4 long planks fastened on the sides. The pallet must be thoroughly cleaned of odors, eliminate all irregularities with sandpaper. After the surface is even, the product must be painted with wood paint and varnished on top. Using a marker, mark the places where the hooks will be attached. The hanger from the pallet is quite massive, and the fastening must be chosen reliable. Attach the hooks to the pallet, then, using self-tapping screws and a drill, hang the pallet on the wall. Additionally, shelves and holders can be nailed.

From longitudinal and transverse boards

This roomy model will fit shoes, hats, jackets. To begin with, fix 2 longitudinal boards on the wall: from below and from above. The length is determined depending on how wide the shelves you are planning to make. With the help of self-tapping screws longitudinal boards attach cross bars. The interval should be sufficient to store clothes, the number can be any - choose at your discretion. In order to make an even fastening of the elements, use the level. To build a support, use the bars (in the future it will be a shelf for shoes). Fasten the connections with metal corners. Also, with their help, fasten a shelf on top (for hats, hats, gloves) perpendicular to the longitudinal boards. The final step will be attaching hooks and decorating.

hanger manufacturing process

Cut out a template from a sheet of plywood and transfer it to a beam with a marker. Drill 2 holes in the inside, cut out the circled template with a jigsaw. Mark the hole for the hook, then drill (diameter 5 mm). Cut a recess in the inside of the drilled hole (using a file with a large notch), place a nut in it. A recess is needed in the future so that no hooks form during operation. Saw off narrow hand saw 20 centimeters of wire, round off one end with a file, chamfer the second end and cut a thread with a metal-cutting die (length about 5 mm.). Drill a hole for the hook, which must be bent, then insert and securely fix with a nut.

decoration

Unusual design solutions can transform any, even unsightly hallway. For supporting classical style the hanger can be sheathed with leather (leather substitute) or preserve the natural beauty of wood, if it was used. Hooks painted with bronze or gold paint. Cover the shoulders with velvet, satin fabric. For country use additional accessories in the form of horns, it is permissible to cut them out of wood. For the retro style, the color can be artificially aged; the decoupage technique is used for Provence. In the role of prints, glue or draw flowers, images of birds, landscapes. IN modern interior experimentation allowed. unusual shapes, original accessories, silhouettes, complex intricate patterns. You can decorate and give originality with rhinestones, sequins, decor self made, drawings, bows. Apply images of your favorite cartoon characters, series, books.

To avoid cracks in the wood - before screwing in the screws, it is recommended to drill holes with a drill.
The diameter of the self-tapping screw must be larger than the drill. Fill the holes in advance with glue, and then screw in the self-tapping screw - so the product can carry a lot of weight of the clothes and will be more wear-resistant and strong.
For a metal hanger, use paints and coatings that resist corrosive processes.
At the planning stage, it is imperative to take into account the dimensions of the wall, to think about exactly how you will fix the workpieces, taking into account the material from which the wall is made (concrete, wood, plastic).
All wood blanks must be processed grinder or sandpaper, and at least 2 times: first coarse grit, and then fine grit.