The advantage of acrylic bathtubs is their lightness, but this moment is also their disadvantage, since a rather fragile and thin construction may not withstand and burst upon impact or be damaged by a heavy object falling.
Agree, I would not want to spoil the new plumbing during installation. In general, the installation acrylic bath and with your own hands is an easy task. The main thing is to understand the principle of work and adhere to technology.
Below are various ways installation of the bath, the procedure for connecting the siphon and sewer supply is described. All instructions are accompanied by visual photos and videos.
Acrylic bathtubs are very beautiful, have original design and varied color solutions. At the same time they have their weak sides and vulnerabilities.
Therefore, it will not be superfluous to find out what problems you may encounter during installation and subsequent operation, and how to prevent them.
Colored acrylic bathtub unusual shape will become a bright and original element that can decorate the interior of any bathroom
Among the advantages are:
- Plastic. Acrylic lends itself well to molding and subsequent processing. This property of the material determines the presence of a huge variety of forms of acrylic bowls.
- Lightness. The acrylic bathtub is lightweight (15-25 kg), so one adult man can easily handle its installation.
- Priority heating technology. Acrylic itself is warm material. In addition, it has low thermal conductivity, acrylic bathtubs are able to retain heat for a long time, the water in them cools down much more slowly than in cast iron structures.
- maintainability. Plumbing and acrylic products in general lend themselves well to repair and restoration. If the damage is significant, then you can restore the bath using an acrylic liner, which is made for a specific design, and then simply inserted into the old container.
As for the shortcomings, they are also present. We must not forget about the disadvantages. Following the guidelines below will help you avoid possible problems and extend the life of the acrylic bath.
To disadvantages acrylic sanitary ware include:
- sensitivity to high tº. Acrylic does not hold up very well high temperature. When heated above 60 degrees, it can be deformed, so you should not pour too much into the bath. hot water.
- Fragility. If you accidentally drop a heavy metal object into the bathtub, a step like uneven surface, its bottom can be pierced through.
- Vulnerability. Acrylic bathtub is capricious in - it cannot be rubbed with hard brushes, washed with powders containing abrasives, since the enamel is very susceptible and can be easily scratched from exposure to solid particles.
And it should also be noted, if not a drawback, then the inconvenience that the one who first sank into an acrylic bathtub faces. Due to the thinness of the material, the bottom may sag slightly under the weight of a person. However, you get used to this feature of an acrylic bath quite quickly.
Image Gallery
Conclusions and useful video on the topic
The assembly of the frame and the installation of a bathtub with a plastic screen are described in the following video:
Video instruction on how to properly assemble a factory metal frame for an acrylic bath:
Acrylic bathtubs of angular, round or asymmetrical shape are installed only on the factory metal frame. Manufacturers apply detailed instructions, according to which any man can cope with this work on his own. However, it is better to entrust the installation of a hydromassage bathtub to specialists, since it requires the connection of complex electrical equipment.
Have something to add or have questions about installing a bathtub? Share personal experience installation of plumbing and please leave comments on the publication.
First of all, of course, a few words should be said about the manufacturer acrylic bathtubs B.A.S. This company continues to amaze its customers and partners by proving that bathtubs made in Russia are no worse than their foreign analogues.
The main products of this company are hydro and air massage acrylic bathtubs.. Among the obvious positive aspects of acrylic bathtubs produced by BAS, the following can be distinguished:
- bas acrylic bathtubs are made using multilayer polymer plastic from the company senoplast - a combination of acrylic and ABS plastic gives strength and reliability to the bath;
- the same plastic from senoplast also has an antibacterial effect, which protects the bathtub from the growth of various bacteria
- bas bathtubs are manufactured using high-quality Italian equipment, so the products can compete with European products
- acrylic bathtubs are reinforced with a steel frame that is well protected from water
- products are manufactured in Russia and therefore its features take into account the arrangement of Russian bathrooms
Buyers about BAS bathtubs
It is interesting what the buyers themselves say about bas acrylic bathtubs, it is quite easy to find reviews on the Internet. It turns out that most of the buyers were very satisfied, saying that the bas acrylic bathtub works great. Buyers happily share their impressions that the bath of this company:
- does not scratch, despite the fact that the shower periodically falls into it
- the side is very thick and you can sit on it
- the bath retains heat perfectly, and therefore you can bathe in it for a long time, even if hot water is in limited quantity
- the bath is equipped with beautiful comfortable armrests
- takes up little space, all models are well thought out
- the only detail that earned a few negative reviews was the hydro and air massage system - they say that it does not last very long, and repairs are quite expensive
It was also interesting that many buyers installed and assembled both an acrylic bathtub and a bathroom curtain on their own. Of course, not everyone can do this, but still we can assume that this indicates the quality of the product, since even a non-professional assembler will do everything with high quality. However, the installation of a bas acrylic bathtub can be done by professionals - it all depends on the capabilities of the client. The instruction that comes with the bathtub is quite clear and simple, so the assembly of the bas acrylic bathtub does not present any difficulty.
Three great examples of BAS products: Atlanta, Florida and Laguna
One great example is the acrylic bathtub. bas atlanta which has certain advantages. So, the dimensions of this bath model are quite modest, it is suitable even for a small bathroom - 170 by 70 cm. However, the capacity is very good - 205 liters. Since the baths from BAS are mostly hydromassage, Atlanta is no exception - it is equipped with six jets - three on each side.
The mandatory set includes a standard set:
- metal frame that guarantees the strength of the bath
- bathtub legs that allow you to adjust the height of the bathtub and make sure it is stable
- front panel that will close the space under the bathroom and give the interior a complete look
- the necessary device for draining and overflowing
In terms of design and space optimization, this is a very simple medium-sized rectangular bathtub that is comfortable enough, but does not take up too much space and does not distract too much attention, so it will easily fit into almost any modern design.
Another example of a great bathtub is the acrylic bathtub, which is a corner asymmetrical bathtub. It is quite compact on its own - 160 cm long and 88 cm wide, and yet has a beveled corner, so it will become ideal option for a small space. Although her style is quite simple and elegant, if desired, she can be distinguished - for example, create a visually separate space for her, with the help of decor elements, tiles of a different color or shade, additional shelves, etc. This bath, in addition to its ergonomic design, also has an interesting shelf for hygiene items, or even to sit on it.
The equipment here is standard - the same as in Atlanta. Capacity is also 205 liters. But there are more hydromassage jets - there are eight of them.
The last one should, of course, consider such a model as an acrylic bath bas lagoon, which is somewhat similar to the Florida model. However, the Laguna is larger in size - 170 by 110 cm. The capacity is also much larger - 295 liters. And the number of hydromassage nozzles is the same - eight pieces. The package is standard.
This bath is suitable for a medium-sized room, due to the fact that, although it is asymmetrical, it is still quite large and is unlikely to fit well in a small room. This model is also very conveniently equipped with a shelf for bathroom accessories and has ergonomic design. At the same time, it will most likely be one of the main elements in the design of the room, this is facilitated by its rather large size. Therefore, it can be distinguished by directional colored lighting, or other decor options. Also, great idea will hang large mirror next to the bath, so that it expands the space, and the bath no longer seems to be something bulky.
In addition to the standard equipment, BAS offers its customers a fairly large selection additional options. These additional features can be divided into several groups:
- Aero and hydromassage lotions: various types of massage - dorsal, shiatsu, foot; air massage from 6 to 12 nozzles, hydro-aero-pipe massage.
- Faucets: cascade mixer or even the whole set: spout, mixer, shower holder.
- Backlight: different kind lighting and chromotherapy.
- Pleasant little things: a headrest, armrests, products for cleaning the massage system or the bath itself, a pillow for the on and off buttons.
BAS provides its customers with really very wide opportunities according to the choice of model and set of bath equipment, plus you can choose a design curtain.
OPERATION OF BATHS "BAS"
Thank you for purchasing a bathtub. trademark"BAS". Whirlpool baths "BAS" are modern technologies and original lines that provide the comfort of hydromassage, which will strengthen your health and give you many pleasant moments.
This manual describes the functions of the baths, installation requirements, care and use.
PRECAUTIONS
In order for the bath to bring you benefits, to work for a long time and reliably, a number of conditions must be met:
1. If your body has disorders of the cardiovascular system, then consult a doctor (how much hydromassage is useful for you).
2. Consider installing filters (for water purification) - this will increase the life of your faucets and hydromassage bath equipment.
3. Do not turn on the hydromassage without filling the tub with water.
4. Do not allow the tub to be walled up in tiles, panels or hard mortars, restrict access to hydromassage equipment that prevents the tub from extending at least 0.5 m from the wall.
5. The bath is connected to a single-phase alternating current with a voltage of 220V. To avoid defeat electric shock, the bath must be earthed through a socket with a connected earthing contact.
TECHNICAL DESCRIPTION AND EQUIPMENT
Standard equipment of bathtubs is shown in the following table
| №n/n | Type of components | Picking lists and quantity, pcs | ||||||
| A | B | C | D | E | F | G | ||
| 1 | Acrylic bathtub (with frame, upper panel clamps and additional equipment) | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| 2 | Bath piping (drain-overflow) with siphon \ without siphon | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| 3 | Threaded stud M12 | 4 | 6 | 6 | 8 | 7 | 5 | 7 |
| 4 | Leg PVC bathtubs M12 | 4 | 6 | 6 | 8 | 7 | 5 | 7 |
| 5 | Panel fixing bracket | 2 | 2 | 3 | 2 | 2 | 2 | 4 |
| 6 | Decorative clip (with press washer) | 4 | 4 | 6 | 4 | 4 | 6 | 8 |
| 7 | Washer M12x36x3.4 | 4 | 4 | 6 | 4 | 4 | 4 | 8 |
| 8 | Nut M12 | 12 | 16 | 18 | 20 | 18 | 14 | 22 |
| 9 | Mounting screw 4.2x25 | 4 | 4 | 6 | 4 | 4 | 6 | 8 |
| 10 | Manual | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
Equipment list A- for baths of the models "CAMERON", "LIMA", "TESSA", "VERONA", "IBIZA", "BREEZE", "ALEGRA", "VECTRA", "MALDIVE", "STYLE", "SAGRA", "ATLANTA" ", "NEPTUNE", "MALTA", "AKHIN", "FLORIDA", "FANTASY";
Equipment list B- for bathtubs of the INDICA, JAMAICA, LAGUNA models;
Equipment list C- for bathtubs of the CAPRI models;
Equipment list D- for bathtubs of the FIESTA models;
Equipment list E- for bathtubs of the NICOLE models;
Equipment list F- for bathtubs of the models "RIOLA", "KHATIVA", "IRIS", "IMPERIAL", "MEGA", "FIREWOOD";
Equipment list G- for bathtubs of the RIVIERA models;
Additional equipment includes: hydromassage, back massage, Shiatsu massage, air massage, lighting, chromotherapy, control panel, mortise mixers and handles.
Depending on the bathtub model, the manufacturer provides panels (screens) for bathtubs (front, side), shower curtains and headrests, which are not additional equipment and are not included in the kit. The manufacturing company reserves the right to make changes to the design and equipment of bathtubs.
TRANSPORTATION OF BATHTUBS
The bath must only be transported in a horizontal position. When transporting and installing the bath, care must be taken not to damage the piping systems and electrical equipment. Bath should be moved only for the body or frame. Must be avoided mechanical damage bath body, panels, as well as to exclude the possibility of exposure to chemically active reagents on the surface of the product. When transporting in the cold season, before installation, the bath must be kept at room temperature at least 6 hours.
ATTENTION! It is strictly forbidden to move the bath by pipelines, nozzles, handles and other equipment! Inspect the goods for compliance with the order, the absence of mechanical damage, completeness, the availability of accompanying and warranty documentation.
REQUIREMENTS FOR THE INSTALLATION OF THE BATH
The room in which the bath is installed must meet the following requirements:
Tiled and Finishing work must be completed;
The possibility of easy access to the components and assemblies of the bath for its preventive warranty maintenance and repair should be provided;
The presence of a power line with the required parameters and a socket with a connected ground contact. The power supply of the bathtub connection point must be provided by a double-insulated electric cable with a cross section of at least 2.5 mm2 and is in accordance with the norms and standards of the EU;
Availability of water supply and sewerage. Sewage pipe the bathroom should not rise above the floor at the connection point by more than 10 cm. If this is not possible, then a podium must be provided under the bath;
BATH INSTALLATION REQUIREMENTS
The installation of the bathtub must be carried out only by qualified specialists, in compliance with the following requirements:
Installation of a bathtub without a frame, as well as with a modified frame, is not allowed. Legs are used to level the bathtub and to adjust the gap between the bathtub panel and the floor. The bath must rest on all points of support in order to exclude uneven distribution of the load and, as a result, the appearance of microcracks in the bath body;
The bathtub must not be walled up in tiles, panels or hard mortars. To prevent moisture from getting under the bathtub or on the hydromassage equipment, the seams between the bathtub and the wall must be sealed with sanitary silicone.
Avoid dirt and construction dust on the surface of the bath. This can cause clogging and failure of the whirlpool equipment or lead to scratches on the surface of the tub, during subsequent unprofessional cleaning.
When performing work on the withdrawal of water supply and sewage pipes, it is necessary to take into account the linear dimensions of the bath. Otherwise, the connection may be difficult, since the pipe outlets may abut against the stiffeners, aggregates and fittings of the bath, and the bath cannot be installed close to the walls. Structural changes in the arrangement of equipment and pipelines of the bath, cutting of mounting clamps, and so on are strictly prohibited.
The electrical wiring of the room must have an individual differential switch 30mA, a magnetothermo 2.4-4A or another common connection (CEI-64-8) and installed in the common switchboard of the room. It is strictly forbidden to install the specified knife switch under the bathtub!
ATTENTION! Failure or incomplete fulfillment of the above requirements does not provide for the preservation of the warranty conditions for service or repair for such a bath.
BATH INSTALLATION
Install the bathtub on legs (Fig. 1) The manufacturer allows the legs to be equipped with an M12 bolt, instead of the corresponding threaded studs. Equipment legs A(fig. 1) (2 pcs.) - are installed on the front (front) side of the bath, along the edges, on the left and right (for the bath " RIVIERA"- 4 pieces, all in front). Equipment legs B(Fig. 1) - other remaining front and rear legs. The legs are attached to the frame with the upper pair of M12 nuts, which also serve to adjust the height of the bathtub.
Install a drain-overflow device (Fig. 2), a siphon (may not be included in the kit) on the bathtub, and adjust the height of the bathtub. The distance from the floor level to the lowest point of the siphon must be at least 15 mm. Make sure the bathtub is adjusted and rests on all points of support.
Install the panel onto the bathtub by snapping it onto the top fixings (fig. 6 and 7). On some models of symmetrical and asymmetric bathtubs "BAS" it is possible to cut the panels along the length (no more than 2 cm per side). In addition, if you plan to install a side panel on your bathtub, then first install the top fasteners under it that come with the side panel in the kit. Adjust the verticality of the panel. The bottom of the panel should be adjacent to the plane of the corner, installed on the extreme legs. Depth of landing of a corner is regulated by the bottom pair of nuts M12. The corners must be equally adjusted to each other in height, and be symmetrical with respect to the panel.
Using a 3.5 mm drill (the size is indicated for a 4.2x25 mm self-tapping screw), drill in the lower corners and panels through holes(Fig. 4 and 5).
Remove the panel from the bathtub and connect it to the sewerage and water supply systems (see Connecting the bathtub to the water supply and sewerage network), as well as to electrical network 220 V (see Connecting the bath to the electrical network). After that, carefully push the bath firmly against the wall, and once again make sure that it is stable on all points of support, and all connections are made correctly.
6. Install the panel on the bathtub and fix its bottom in drilled holes self-tapping screw with a press washer (Fig. 8).
7. Close the head of the self-tapping screw with a decorative cap (Fig. 9).
ATTENTION! IN ORDER TO AVOID MOISTURE GETTING OUT OF THE BATH, PRODUCE MANDATORY PROCESSING OF THE SEAMS WITH SANITARY SILICONE AROUND THE ENTIRE PERIMETER OF THE BATH!
CONNECTING THE BATH TO THE WATER SUPPLY AND SEWER NETWORK
The connection of the bath to the water supply and sewerage network must be carried out by a qualified plumber.
The bath kit includes a semi-automatic drain device, which, after being installed on the bath, is connected to sewer network stationary, through flexible corrugated or rigid pvc pipe(not included). A sewer drain with a diameter of 40-50 mm is removed at the site of installation of the bath into the floor or wall, taking into account the linear dimensions of the bath. When the drain pipe is located in the wall optimal height a distance of no more than 2 cm from the floor level to the lower edge of the pipe is considered.
Connecting the bath to the water supply network if it is equipped with a mortise mixer. The pressure in the network should be 3-5 atm. At pressures above 5 atm., pressure reducers should be installed and adjusted to the specified standards.
Places for connection to the water supply system should be placed taking into account the linear dimensions of the bath and its units and equipped with taps that are disconnected from the main line. Connection to the system is carried out through a flexible plumbing connection ( water hoses). The length of the hoses must allow the bathtub to be moved away from the walls, and the distance must not be less than 0.5 m. Recommended use of water filters. The absence of filters can lead to clogging of the whirlpool jets and the ingress of metal scale into the ceramic cartridge of the mixer, which will lead to their failure.
ATTENTION! Mortise mixers are completed with a set flexible hoses standard sample. If the length of the flexible hose is not enough to connect to the system or connect between the elements of the mixer, then it is purchased separately, taking into account your dimensions for connection. The bathtub manufacturer is not responsible for the nature of the set of in-line faucets, for damage to the elements of the hydromassage system caused by their contamination when using unfiltered water containing rust, sand, chemically active impurities, as well as for breakdowns or incorrect operation of the bath equipment connected to the system water supply with non-standard pressure in it.
Leave the tub unattended while filling it with water. Overfilling the bathtub with water can lead to failure of the air massage system, without preserving the warranty conditions for the operation of the product.
Rotate the drain-overflow cover around its axis or with a load on the bath plug.
CONNECTING THE BATH TO THE ELECTRIC NETWORK
The electrical equipment of the bath is powered from a single-phase alternating current network, in accordance with the table below.
| Function | Voltage, V | Frequency, Hz | Power, kWt* |
| Hydromassage | 220/240 | 50 | 0,9-1,5 |
| Air massage | 220/240 | 50 | 0,7-0,9 |
*power is indicated depending on the bathtub model
The connection of the bath to the electrical network must be carried out by a qualified specialist with the 3rd and higher tolerance group. How to connect hot tubs to the network:
Yellow-green wire - "ground";
Brown wire - "phase";
Blue wire - "zero";
The bath must only be connected to a separate residual current circuit breaker (RCD) with a rating of 30 mA and located outside the bathroom.
It is allowed to connect the bathtub to a 220 V network. In this case, they are purchased separately and installed independently. Each unit of equipment intended for connection to the network must have an individual connection to the electrical network.
Connect the units together, in one plug, etc.
Use a bathtub with a socket or plug without a good grounding contact.
Ground the bath through heating, plumbing and sewer equipment.
Operating the bath with a damaged power cord, or with a faulty or unconnected ground.
Conduct engineering works with the bathtub plugged in.
HYDROMASSAGE AND OPTIONAL EQUIPMENT
The following elements of hydromassage equipment can be located on the bathtub (see View A):
Email Hydromassage motor with hydraulic pump
Air massage compressor
bathroom controls and knobs
hydromassage nozzles (jets) (reverse side)
piping system
Additionally, the bath can be installed
air massage (installed in the bottom of the bath, see Fig. 1)
Mortise mixer (see fig. 2)
Back massage (see pic 3)
Shiatsu massage (back massage or back massage + foot massage) (see Fig. 4)
Chromotherapy (see figure 5)
Backlight (See Figure 6)
Head restraints (see fig. 8)
BATH CONTROL
Bath functions are controlled by the following equipment:
A) Jets (jets) for hydromassage.
Provide adjustment of the direction and strength of hydromassage jets. The direction of the jet can be easily changed by turning the nozzle nozzle within a 30 degree angle. The power of the water jet is regulated by turning the nozzle of the nozzle around its axis. The maximum jet flow is achieved by fully opening the jet nozzle counterclockwise (open nozzle).
B) Button on / off. Functions of a hydromassage with the regulator of supply of air (RPV). Provides on/off hydromassage system by pressing in the center. The RPV controls the amount of air mixed with the water jet during the operation of the hydromassage system, due to the injection process. By turning the knob, you can change the amount of air flowing with the jet of water from the hydromassage jets. The power of the jet increases with the supply of air into it.
IN) Button on / off. Aeromassage functions (chromotherapy illumination). Provides on / off aeromassage system. When switched on, the compressor pumps air under pressure through air nozzles installed at the bottom of the bath. At the same time, small air bubbles break out to the surface, massage and enrich the skin with oxygen. Can be used to turn on/off. Chromotherapy highlights.
G) Crane-balance (turbopool).
Switches the operating modes of the hydromassage system between the general hydromassage function and the back massage function (Shiatsu massage). Adjust the desired distribution of water supply by the indicated functions by turning the “flag” of the switch.
D) Electronic control panel for bath functions (No. 2).
Buttons for adjusting the power of the air massage function
Button on / off. air massage functions
Button on / off. Functions of chromotherapy (backlight)
Button on / off. Hydromassage functions
E) Electronic (touch) control panel for bath functions (No. 3).
Remote control power on/off button
Button for turning on / off the hydromassage function
On / off button for backlight / chromotherapy function
Multifunctional button for switching operating modes: radio station frequency ( MHz) / station channel number ( ch) / radio frequency tuning mode (flashing inscription TUNE) / volume control mode ( d) / air massage power level adjustment mode (number from 1-10 ). Also used as a selection confirmation button when memorizing radio stations. Up to 10 tuned channels can be stored in memory ( CH).
Mode setting buttons: volume level / radio station frequency / radio station channel number / air massage power level. The setting is carried out depending on the mode selected by button 5 ( SET).
Radio on/off button.
Button for turning on / off the air massage function.
ATTENTION! If your bathtub is equipped with a control panel, then if the water level is lower than it should be in the bath, all functions are turned off, except for radio and air massage.
HOW TO USE THE WHITE BATH
ATTENTION! Never turn on the hot tub until the water reaches a level 5-6 cm above the opening of the main whirlpool jets. Avoid high thermal impact (above 65 degrees Celsius) on the surface of the product - this can lead to its damage! It is forbidden to turn on the hydromassage function with closed jet nozzles. Before turning on the hydromassage system, make sure that the jet nozzles are not directed upwards and that the balance tap is not in the back massage (Shiatsu massage) position. During the operation of the hydromassage, it is forbidden to block the grate of the water intake valve, preventing the flow of water into it. After using the bath and draining the water, it is recommended to blow the air massage jets by turning on the air massage function for 1 minute.
Never use the bathroom after taking alcohol or medicine. Hydromassage in medicinal purposes can only be carried out on the advice of a doctor who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath strengthens your health, a warm or slightly hot bath relieves stress. To relax muscles and relieve pain, take a bath up to 40 degrees Celsius. The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes
The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And, if you feel sleepy while taking a bath, turn off the hydromassage device for a while and cool the water.
Contraindicated for overweight people hot tubs when the water temperature exceeds 38 degrees Celsius.
BATH CARE
For daily bath cleaning, use a liquid cleaner that is harmless to acrylic and plastic surfaces(see cleaning agent instructions) and a cloth made of soft tissue. The manufacturing company offers you a specialized cleaning agent "TIM-PROFI" adapted to our products. To maintain the shine of the bath, you can wipe it with a cloth with a polishing agent. To wash the bath, use only soft cloth napkins.
Deposits on the surface in the form of scale are removed with a soft cloth moistened with lemon juice or wine vinegar.
Surface scratches or burn marks from cigarettes can be removed by lightly sanding with a fine-grained sandpaper(No. 1000/2000) with water. You can restore the shine of the surface with a liquid polishing agent.
ATTENTION! To remove dirt from the surface of the hot tub, never use metal brushes or tools, as well as solvents or detergents with abrasive additives. Also avoid contact with ammonia or chlorine on brass and chrome parts.
CLEANING THE BATH HYDRAULIC SYSTEM
This type of cleaning when using hard water (over 15 salt deposits per 1 cubic meter water). In addition, it is recommended to clean the bath hydraulic system. Twice a year in the following way:
Fill up the bath hot water(40 degrees Celsius).
Pour in liquid detergent at the rate of 2 g per 1 liter of water and run the hydromassage system for about 5 minutes.
After that, turn off the hydraulic pump and drain the water from the bath.
Refill the bath cold water and turn on the hydromassage for 2 minutes.
Drain and wash the bath (see "Care of the bath").
SIMPLE FAULTS, CAUSES AND WAYS TO ELIMINATE THEM
| Fault occurring | Possible reason | Remedy |
| Hydraulic pump does not turn on | No voltage in the power circuit (mains 220 V) | Call a specialist (electrician) |
| The hydromassage button (aeromassage, backlight, chromotherapy) does not turn on | The plastic tube connecting the button and the electro-pneumatic valve jumped off the function enable button | Attach the plastic tube to the base of the button and restart the system |
| Jet nozzles closed | Turn counterclockwise to open the nozzles | |
| Hydraulic pump works but no water comes out of jets | The formation of an "air lock" in the hydromassage system | Disconnect the bathtub from the 220V network, fill it with water and loosen (no more than 1 turn!) the upper nut of the hydraulic pump tee to bleed air from the system. After that, tighten the nut tightly and restart the system. |
| Increased vibration in the operation of the hydraulic pump | Loose motor mount metal frame baths | Tighten the engine mounting bolts. |
Technical features
IN Lately Acrylic bathtubs are very popular among buyers. A wide range of sanitary products offers options for various bathtubs. Many modern companies demonstrate high-quality products that will be easy to use. Among them, the domestic brand Bas stands out, which produces interesting models hot tubs. With their help, you can take the quality of rest to a new level.
Technical Features
Russian company Bas has been delighting its customers with bathtubs, showers and bathroom accessories for over 15 years. Products are manufactured using high-quality Italian equipment in strict accordance with technological parameters and international standards. Products are sold not only in Russia, but also in Kazakhstan and Belarus.
Bas bathtubs are made of high quality acrylic, thanks to which the product is resistant to corrosion and other types of chemical attack. This material is characterized by its plasticity, so the manufacture of bathtubs with its help is an easy process, the result of which is characterized high level quality.
Bas brand's wide range showcases classic and modern models baths white color, among which you can definitely choose the most suitable option for small and large bathrooms. The production of bathtubs is carried out using two different technologies.
- The traditional way - "SprayGan". With it, the acrylic base is strengthened polyester resin and fiberglass.
- The method developed Italian company SIRTEK. In the manufacture of the frame, a complex two-component composition of high-strength polyurethane foam is used.
The manufacturing process itself includes the formation of the shape of bathtubs from a polymeric multilayer material - ABS sheets. With the help of high-end equipment, it is given the necessary shape of the future product and acrylic is applied, which will be 10% of the sheet thickness. This product has a high degree of strength and impact resistance.
The manufacturer Bas also offers its customers a range with a hydromassage function. The set of such products includes jets that, with the help of a directed movement of water jets, help to achieve complete relaxation and help to get the maximum health benefits.
Advantages and disadvantages
Bas products are characterized by a number of advantages.
- High quality materials. In the manufacture of products, raw materials are used from large European manufacturers that have a positive reputation. The color of the products does not fade with age, the surface remains smooth, and the frame does not sag under heavy weight.
- Impact resistance. Production technologies make the surface of the baths resistant to mechanical damage, significantly increasing their service life.
- Antibacterial surface effect. It prevents bacteria from multiplying in a humid environment, making bath operation even more comfortable and safe.
- Easy installation. The product manual contains complete installation information. You can easily and quickly install a bathtub yourself or use the assembly service of professionals from the company.
- Convenient operation. The product form provides for all the necessary nuances of its use. Smooth lines and the necessary recesses for a comfortable pastime and quality rest attract the attention of buyers who value comfort.
- Hydromassage function. Models with this function make the process even more enjoyable, positively affecting the blood circulation in the body and allowing you to reduce the intensity of cellulite and increase stress resistance.
The disadvantages of products from the Bas brand include some characteristics.
- Insufficient points of support. When installing baths of complex shapes, you may encounter the problem of a lack of support points for comfortable use of the product. This problem can be solved by contacting the service center of the company or independently using improvised means.
- Plastic nozzles. Customers may have problems with leaking nozzles that will have to be replaced.
- Price. For many buyers, the price category for acrylic products seems overpriced, although the manufacturer claims the availability of its products and the ability to choose a model for any budget.
The manufacturer's products have a significant list of advantages, but no one is immune from unpleasant incidents. In any case, Bas consultants are patient with their clients and are ready to delicately solve any problem that arises.
Criterias of choice
The lineup sanitary products from the Bas brand is quite large. Among it, you can easily find a bath that will meet all the needs of customers. Choosing suitable product, the first thing the buyer relies on is the size of his bathroom. Especially for this, the range of the manufacturer includes products of different sizes. Dimensions on average vary from 1300x700 to 1800x1500 mm. For very small bathrooms, you can choose corner products which save a lot of space.
Models "Nicole" 170x102 cm and "Fantasy" 150x88 cm have similar characteristics.
Depending on the functionality, ordinary acrylic bathtubs and hydromassage models are distinguished. In fact, each model provided in the catalog can be equipped with a hydromassage function, the difference will be only in price.
Another important parameter is the shape of the product. The assortment of the Bas brand includes such bathtubs of such a form as:
- oval;
- rectangular;
- angular;
- asymmetric;
- non-standard.
When choosing, it should be borne in mind that the more complex the product, the more support points it requires, and the more it is prone to deformation.
It is better to stay on more traditional oval or rectangular models. Products are attractive to buyers not only for their appearance and quality. Bas bathtubs are ergonomically designed to fit the human body and its curves. In such models, it will be pleasant and comfortable to take water procedures.
The weight parameter for acrylic bathtubs does not play a special role, since such products weigh much less than cast-iron options and do not cause difficulties with climbing to the floor and during the installation process.
Range overview
In the manufacturer's catalog, products are divided according to the shape of the product for a comfortable search for a suitable product.
Rectangular baths
standard model "Ibiza" has dimensions of 1500x700 mm. It is ideal for a small bathroom, and due to the depth of 430 mm it will allow you to cover with water most body. Bath screen height - 530 mm, holds 175 liters.
The ergonomic shape will allow you to enjoy water procedures, feeling comfortable. With the hydromassage function, it will include 6 nozzles - 2 large and 4 small. It can also include a shiatsu back massage function complete with a regulator faucet for balance control of water flows.
The kit includes several lighting options, LEDs, and an electronic control panel. There are several faucets to choose from: 2-position with switching to a shower or a cascade spout.
Models will have similar characteristics "Verona" 150x70 cm, "Malta" 170x75 cm and "Rio" 170x70 cm.
Product "Jamaica" with dimensions of 180x80 cm will be an excellent tool for quality rest. Thanks to its large size and depth of 430 mm, it will allow the body to be completely immersed in hot water. Smooth curves of the bath will make you feel comfortable. The presence of 8 or 12 jets for air massage will help you quickly relax and relieve stress.
Water volume - 230 l, screen height - 630 mm. Like the previous model, it includes backlighting and LEDs, an electronic remote control. Also included is the possibility of back massage "shiatsu" and cascading 2-position mixers.
It is also worth paying attention to the Fiesta model 194x90 cm.
Rectangular bath "Lima" size 130x70 cm is suitable for a small bathroom or for a children's bathroom due to its small dimensions. It holds only 95 liters and is characterized by a depth of 420 mm. It can include the function of hydro (6 jets) or air massage (8 or 12 jets). The height of the screen is 540 mm. It is possible to install back massage and LEDs. Backlight and other functions are adjustable with electronic remote control. In addition to the options considered, the actual products of a rectangular shape are models "Atlanta" 170x70 cm and "Indica" 170x80 cm.
Asymmetric bathtubs
Product "Lagoon" 1700x1100 mm - corner option bath, which is popular with customers due to its ergonomics and stylish appearance. Despite its compactness, it has sufficient dimensions so that the owner can comfortably enjoy water procedures. It holds up to 295 liters, and the depth in the center is 440 mm. Screen height - 550 mm. Includes the possibility of installing hydromassage in 6 jets or air massage (8, 12 jets). It has a special recess for the convenience of foot massage.
Model "Alegra" has dimensions of 1500x900 mm. Unlike the previous model, it does not have a side, due to which it receives a large area for water procedures with the ability to save space in the bathroom. Depth in the center - 450 mm, holds 220 liters of water. The simple design features smooth lines and comfortable operation. Massage nozzles are scattered along the walls of the bathroom for better relaxation.
Also popular are such models of asymmetric baths as: "Capri" 170x80 cm, "Sagra" 160x100 cm, "Florida" 160x88 cm.
Symmetrical baths
For those who want to buy a "mini-jacuzzi" you should pay attention to the product "Mega" 1600x1600 mm. It has positive reviews due to ease of use and the possibility of obtaining quality rest due to the successful dispersal of nozzles: for hydromassage - 6, for air massage - 8 and 12. It is possible to backlight and turn on LEDs in the kit to create an atmosphere and mood. The capacity is 450 l, the depth of the tub is 480 mm and the height of the screen is 610 mm. There is a compartment for the possibility of receiving a foot massage without filling the tub with water completely.
Instructions for Bas Acrylic Bathtubs
Thank you for purchasing a BAS bathtub.
- Foreword
Bathtubs "BAS" are modern technologies and original lines that provide the comfort of taking water procedures.
This manual describes the functions of the baths, installation requirements, care and use.
Attention: In order for the bath to benefit you, work for a long time and reliably, a number of conditions must be met:
1) Ask your doctor how much bathing is useful for you.
2) Provide for the installation of filters for water purification.
3) Do not turn on the hydromassage without filling the tub with water!
4) It is forbidden to seal the seams between the wall and the bathroom with hard building materials (ceramic tile, curbs, mortar, etc.)
- Technical description
Whirlpool bath standard equipment:
1. Acrylic bath - 1 pc.
2. Metal frame - 1 pc.
3. Legs - 4-8 pcs. (depending on model)
4. Panel clamp - 2-4 pcs.
5. Self-tapping screws for fixing the acrylic panel - 5-12 pcs.
6. Additional equipment: acrylic panel (screen), drain-overflow device, back massage, air massage, etc. (at the request of the buyer)
Transportation of bathtubs When transporting and installing the bathtub, care must be taken not to damage the piping systems and electrical equipment. It is necessary to avoid mechanical damage to the body of the bath and the screen, as well as to exclude the effect of chemically active reagents on the surface of the product.
Instructions for preparing a place for installing bathtubs:
1. A plumber performing work on the removal of hot and cold water, must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may abut against the stiffeners, aggregates and fittings of the bath. This means that the bath cannot be installed close to the walls.
2. The drain pipe of the bathroom should not rise more than 10 cm above the floor. If this is not possible, then a podium must be made.
3. The legs are used to level the bathtub, so it is necessary to install additional stops under the supporting structure of the bathtub.
4. Wiring for the bath equipment must be double insulated cable with a cross section of 2.5 mm2.
System protection must be based on differential (multiple) tripping (1fn=30mA). The supply cable must comply with EU regulations and standards.
- electrical system
Installation of the electrical system must be carried out by a professional electrician, with an electrical safety approval group of at least group 3. The power supply wiring for the backlight, the hydro-air massage system of the bath must have a “Residual Cutout Device” (RCD) with a rating of 30 mA.
- Attention:
Connect the electrical cable in the following order: blue wire- "zero" brown wire - "phase" yellow-green wire - "ground" The RCD must be located outside the bathroom. It is strictly forbidden to connect the power supply of the backlight, the hydro-aeromassage system of the bath through the plug and socket.
The use of the lighting system without water in the bath is strictly prohibited.
- Description V Hz kW
- Hydromassage 220/240 50 0.9-1.5
- Air massage 220/240 50 0.7-0.9
The power is indicated depending on the model of the bath.
- Equipment for hydro and air massage includes:
1. hydraulic pump
2. air massage compressor
3. function buttons and whirlpool power control
4. whirlpool jets (back side)
5. piping system
- Optional equipment
air massage (jets are at the bottom of the bath)
hand shower, cascade, mixer
backlight
back massage
headrest
pen
- Bath installation guide.
1. Before installing the screen, mark with a pencil or felt-tip pen the location of the centers of the screen fastening plates on the front side of the bath.
2-5. Next, it is necessary to screw 4 M 12 nuts onto the mounting legs, use two M 12 nuts to fasten the mounting legs to the bathtub frame, and with the remaining two M 12 nuts and two M 12 washers, fix the corner of the screen attachment on the mounting leg so that it reaches the edge of the screen . Attach the screen to the tub and drill dia. 3.5 mm to make holes in the corners of the screen attachment (this operation is recommended to be done after removing the screen).
6-7. Mark on the upper part of the screen the points with the centers of the embedded plates for fixing the screen already marked on the front side of the bath, placing them at a distance of 1.5-2 cm from the lower edge of the front side of the bath. In the marked areas of the screen, drill holes for self-tapping screws with a drill with a diameter of 3.5 mm. Next, use the same drill to make holes in the embedded plates of the screen (this operation is recommended to be performed after removing the screen).
8. Using the legs, adjust the bathtub to the height of the acrylic panel, while taking into account the zero level of the upper plane of the bathtub.
9. Install a drain-overflow device on the bathtub, screw on the siphon (not included) and connect to drain pipe bathroom
10-11. Aligning the screen with the embedded baths, it is necessary to screw self-tapping screws into the holes, after which put the plugs on them.
12. After installing the tub, remove the protective film.
13. Install the bathtub wall bracket. A wall bracket is offered to reinforce the rigidity of the tub.
- ATTENTION:
It is forbidden to close the seams between the wall and the bathroom with rigid building materials (ceramic tiles, curbs, mortar, etc.) If the above is not observed, the warranty repair will not be carried out
Instructions for using hydro-, air massage, back massage, water lighting (mechanical activation of functions).
- Buttons for turning on hydro-, air massage, water illumination. (on and off - by pressing your finger inward)
- Switch for hydromassage and back massage. (simultaneous operation of functions is possible)
- Hydromassage and back massage power regulator. (turn knob clockwise)
Electronic (touch) control of the functions of hydro-, air massage, chromotherapy. (1, 2 - air massage power control; 3 - on / off air massage function; 4 - on / off hydro massage function; 5 - on / off chromotherapy function)
- There is an automatic shutdown of the hydromassage and chromotherapy functions, in case of lack of water in the bathroom. Aeromassage is turned off manually after blowing the jets.
Bath care
When washing the tub, use a liquid cleaner that is harmless to acrylic and plastic surfaces (see cleaner instructions). The manufacturer offers you a specialized cleaning agent "TIM-PROFI" adapted to our products. Remove stains with a soft cloth.
Surface scratches or burn marks from cigarettes can be removed by light sanding with sandpaper (#1000/2000) and water. You can restore the shine of the surface with a liquid polishing agent.
- cleaning hydraulic system baths
This type of cleaning is carried out using hard water (over 15 salt deposits per cubic meter of water). It is recommended to clean the bath hydraulic system at least 2 times a year as follows:
1. Fill the tub with hot water (40C).
2. Pour in liquid detergent at the rate of 2 g per 1 liter of water and start hydromassage for about 5 minutes.
3. After that, turn off the electric pump and drain the water from the bath.
4. Refill the tub with cold water and turn on the hydromassage for 2 minutes.
5. Drain and clean the bath (see "Care of the bath").
The manufacturer offers you a specialized hydraulic system cleaner adapted to our products.
WARNING: Never use metal brushes or tools, solvents or detergents with abrasive additives to remove dirt from the surface of the hot tub. Also avoid getting ammonia or chlorine on the brass and chrome parts of the tub.
- How to use the hot tubs
It is forbidden to turn on the whirlpool bath when the hydromassage jets are closed and the water level is 5-6 cm below the jet opening. Never use the bathroom after taking alcohol or medicine. Hydromassage for medicinal purposes can only be carried out on the advice of a doctor who will select the appropriate duration of sessions and water temperature for you.
Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel sleepy while taking a bath, turn off the hydromassage device for a while and cool the water.
Overweight people are contraindicated in hot tubs with a water temperature exceeding 38 C.
Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upwards.
- The simplest faults possible reasons and ways of elimination.
| Fault occurring | Possible reason | Remedy |
| There is no mains voltage. | Call a specialist (electrician). | |
| The hydraulic pump does not turn on. | The plastic tube that connected the button and the pump jumped off the hydromassage button. | Turn off the voltage. Attach layer. handset to the base of the button and restart the system. |
| Jet nozzles closed. | Turn counterclockwise to open the nozzles. | |
| The hydraulic pump is working, but no water is coming from the jets. | Clogged piping system. | See the paragraph "Care of the bathroom". |
| Increased vibration in the operation of the hydraulic pump. | The fastening of the engine to the metal frame of the bath has loosened. | Turn off the voltage. Tighten the engine mounting bolts. |
The manufacturer reserves the right to make changes to the design and equipment of bathtubs..
In winter, the installation of the product is carried out in a warm room after 6 hours from the moment the bath is delivered to the client.
When installing a drain-overflow not provided by the manufacturer, the bathtub is removed from the guarantee.
It is not allowed to get on the surface of the product active chemical substances capable of damaging the acrylic layer.
High (above 80C) thermal impact on the surface of the product is prohibited.
Installation (installation) of the bathtub (shower curtain) and equipment included in the kit is carried out by the buyer with the involvement of specialists licensed to carry out this type of work. The installation is guaranteed by the installer with a note in the warranty card.
Installation of products should allow free access to components and assemblies attachments, as well as to connecting hoses water and air supply.
Dear buyer! The manufacturer sets the warranty period for bathtubs up to 10 years. All equipment falls under this warranty period, except for: a drain-overflow device, hydromassage, aeromassage and any other additional equipment (see clause 7, p. 1 of this manual), for which a 2-year warranty service period is set.
- Warranty service is not provided in the following cases:
– non-observance of installation rules and operating conditions;
– loss of the receipt or warranty card;
– careless storage or transportation by the owner, trade or transport organization;
– attempts of unskilled repair;
– mechanical damage, traces of exposure to chemical and abrasive substances during improper care for the product;
– making corrections to the text of the warranty card;
- RCD (residual current device) is not installed, if there is electrical equipment on the bath;
– use of the product for business purposes.
The company does not take responsibility for damage caused during transportation and delivery.
Warranty service does not cover installation and disassembly costs.
- Video instructions for assembling the frame of the acrylic bathtub Bas
