DIY door decor ideas: photos, tips, master classes. Front door decor in a modern hallway: interesting ideas (20 photos)

Just as a person is judged by their clothes, so any living space is judged by the doors. Therefore, sometimes in order to update the design of a room you do not need to carry out expensive repairs, but you can do original decor doors with your own hands.

Doors perform two complementary functions: firstly, they limit and separate the spaces of one room from another and, secondly, they are elements of the general interior of neighboring rooms or even the entire apartment, which form the visual and functional space of the rooms limited by doors. However, decorating a door can be done not only due to the aesthetic renewal of the living space, but also for trivial reasons, such as the appearance of scratches or cracks, as well as chips on the canvas. In these cases, the main purpose of decoration may be to hide various defects door leaf, but this could be an opportunity to update the design of the entire living space.

So, there are a huge number of ways to decorate interior doors with your own hands, as well as decor front door, and the simplest and most accessible of them are related to decorating door panels using wallpaper.

Wallpapering the door

To carry out such decoration, doors are used both paper and on another basis, as well as fabric and different kinds liquid wallpaper. Any method of updating doors using decoration involves preparing the door leaf for this procedure. Decorating is no exception to this rule. interior door. In the process of preparing for decoration, they not only get rid of the previous coating - this makes it possible to identify and also eliminate previously unnoticed hidden defects of the product.

Preparation for door decor is as follows:

1. In removing old paint. To do this, use a hair dryer to heat up the old paint and scrape it off the canvas with a spatula.
2. In sealing with putty, detected defects, as well as eliminating irregularities. Then all problem areas leveled with putty should be treated with fine-grained sandpaper.
3. In carrying out puttying the entire surface of the canvas. This makes it possible not only to level its entire surface, but to additionally fasten it individual elements, which is very important especially for paneled canvases. After applying the putty and letting it dry, you can go over it again with fine sandpaper.
4. In painting doors with a primer.

The choice of wallpaper and how to paste it, for example, use either the same type or panel pasting different types wallpaper depends on the individual preferences of the one who will do it himself. In this process, the main thing is to correctly select the most suitable glue for certain types of wallpaper, and also dilute it strictly following the instructions included with it. In addition, you need to make sure that there are no missing areas left on the surface that is spread with glue, and you also need to carefully smooth the just pasted wallpaper with a damp cloth or roller to prevent wrinkles and air bubbles from forming.

When drying the pasted surfaces, it is necessary to prevent the presence of drafts. Otherwise, all the work of such door decoration will go down the drain.

Door decor with photo wallpaper, fabric

The decor looks original with fabric wallpaper, as well as with the help of photo wallpaper. However, in the process of decorating the door with fabrics other than the standard one described above pre-training door leaf, it is necessary to take into account the degree of shrinkage of the fabric. To do this, you need to test the fabric, measure a small piece of it and wet it with water until it dries. After this, measure its dimensions again and compare to obtain the shrinkage result. Moreover, if the degree of shrinkage of the fabric is high, it must be completely wetted and allowed to dry, and then you can begin the gluing process.

It is necessary to take into account that you can use both solid fabric and its fragments of different textures, as well as different colors. Now this technique of decorating doors and other surfaces is quite widely used by professional designers, who call it “patchwork”.

Decorating doors using liquid wallpaper

Liquid wallpaper is good because it has versatility, that is, it can cover absolutely any surface, creating very original and varied compositions and patterns. However, they have significant drawbacks - they are afraid of moisture (which means they cannot be used for decorating bathtubs and kitchen doors), and, unfortunately, they are short-lived.

In order to decorate yourself, you will need the following materials, as well as tools:

• the mixture you selected for decoration in dry or diluted form;
• several sized types of spatulas;
• the so-called hopper gun, which is a device for applying liquid mixtures;
• roller;
• the color you have chosen;
• clear nail polish.

For decoration using liquid wallpaper, standard preparatory work have a slightly different appearance in terms of coating the door leaf with an alkyd-based primer and white oil type putty.

Preparing wallpaper mixture for decoration

The process of decorating the door itself consists of diluting the wallpaper mixture with warm water, and it needs to be mixed thoroughly - this can be done absolutely safely by hand. After a quarter of an hour, the mixture needs to be mixed again, but now adding the color you have chosen to it. Moreover, as for the color saturation of the mixture, the more color is added, the more saturated the color will be. For example, for moderate tones, it is enough to dilute one measuring cap of color per five liters of mixture. To realize an idea color composition when decorating, you need to dilute mixtures with different color design in various containers.

When working with wallpaper mixtures, it should be noted that their instructions for use indicate the need to infuse them for 12 hours before using them.

In order to apply the mixture, you need to take it in small portions on a spatula and apply it to the surface, smoothing it and stretching it to the sides. In the process of applying the mixture to the door, you need to ensure that the drawings are followed, and that its layer should be of the same thickness. To give a relief surface, you can use textured roller. After the decor has dried, which will take up to three days, you will need to cover it with clear varnish.

The advantage of working with mixtures is that if you didn’t like the first version of the door decor, as they say, the first thing happened, then the coating can be easily washed off with warm water and then reapplied.

How to decorate a door with a mirror

As for the use of a mirror for decoration, this method is, first of all, preferable for small and dark rooms, as it allows you to visually increase the space of the room, adding light to it.

It is problematic to use classic mirrors for decoration due to the fact that they cannot be adjusted to the size of the door itself or its individual elements. So-called acrylic panels with an amalgam surface, which, in fact, are the real thing, are ideal for this. mirror surface. Moreover, plastic mirrors can be easily cut; they are available in a wide variety color shades, ones that will help you easily realize the most daring original ideas, as well as plans. They cannot be broken, they are light, they attach well to any surface, but they have one drawback - their high price.

But as they say, a good thing a priori, it cannot be cheap, so you have to pay dearly for high quality, practicality, and aesthetics. However, with regard to acrylic mirrors, these are justifiable costs.

To mount these mirrors on itself door leaf, as well as on reverse side acrylic, you need to apply a special deep-penetrating primer, and to fix the elements of a cut or solid mirror, you can use double-sided tape or mounting adhesive.

Decorating the door in vintage style

This style involves the implementation artificial aging products and things, which should contrast with the brilliance of their individual decorative parts for greater sophistication and sophistication. As a rule, products decorated in vintage style are a kind of work of decorative art and are therefore exclusive, that is, they are not similar to any other things.

To decorate a door in vintage style, using the so-called decoupage technique, you need, for example, to have:

1. Acrylic paint, usually white.
2. Various rollers and brushes.
3. Coarse sandpaper.
4. Any mounting adhesive.
5. In addition to assembly glue, there is also PVA glue.
6. Old newspaper paper, as well as old music notebooks.
7. Baguette black or any other dark color.
8. Clear nail polish

In order to paint a door to match the decor of the door using decoupage techniques, it must be removed from the awnings and laid horizontally. Then you need to remove the old paint and you can sand it with coarse sandpaper.

The decoupage algorithm may look like this:

1. Painting is done with a thin layer of white paint. Moreover, this is done with a wide brush in one direction.
2. After the paint has dried, it is sanded to an “antique” state with coarse sandpaper.
3. Then they begin to decorate the central part or its paneled parts of the canvas, having previously torn old newspapers, as well as music notebooks into random pieces of paper and randomly laid them out on areas of the door leaf smeared with glue. You can smooth the paper either with your hands or with a roller. And then you can apply two layers of transparent glue.
4. The perimeter of the paper decor is pasted over with a black baguette or any other dark color using mounting adhesive.

A door decorated with decoupage can be decorated with any other decorative elements, from lace, various bows and ending with multi-colored ribbons.

You can create original decor with your own hands in other ways, using home material, connecting both your own irrepressible imagination, as well as realizing the ideas of your family and friends.

As you know, doors do not last forever, and anything can happen. For example, scratches, chips, and cracks often appear on the door leaf. In this case, you can repair, replace, or carefully decorate the door, hiding all defects.

To decorate a door, you can use not only paper, vinyl and non-woven wallpaper, but also fabric or liquid.

In this case, the canvas should be prepared by removing a layer of paint in advance, filling up uneven areas, cracks and sanding the surface. A layer of applied primer will provide additional adhesion of the wallpaper to the surface of the door.

You can wallpaper both the entire canvas and the panels by cutting out pieces of wallpaper of a suitable size. Don't forget to choose an adhesive that matches the type of wallpaper and dilute it according to the instructions.

Wallpaper classic

Lubricate the cut wallpaper with glue and apply it to the door, making sure that there are no jams or distortions. Smoothing out the wallpaper soft cloth, roller or wide plastic spatula. Carefully trim off the excess with a utility knife. Additionally, you can decorate the door by gluing a frame made of foam plinth on top of the wallpaper.

While the wallpaper is drying, it is advisable to close the windows in the house and prevent the appearance of drafts and sudden temperature changes.

Textile

A door decorated with fabric looks very unusual and attractive. In addition to standard surface preparation, attention should be paid to the fabric itself, determining the degree of shrinkage.

We cut off a small piece of fabric, measure its dimensions, moisten it with water and dry it. After drying, we take measurements again, comparing the readings and finding out the degree of shrinkage. If the value is large, then the entire piece of fabric is also moistened and left to dry before decorating.

Note! You can use not only a single piece of fabric, but also cut pieces of different colors and textures. This technique is called “patchwork” and is often used by designers in interior design.

For fabric, casein glue, a composition based on CMC, as well as Bustilat or Gumilax mastics are best suited. Apply the adhesive to the fabric and apply it to the door, smoothing it with a spatula. When covering a door with fragments, it is important to ensure that they are geometric, otherwise the work will look sloppy.

Additionally, you can decorate the door with beautiful furniture nails, shiny nylon or leather cords, fabric paint, and baguette frames.

Liquid wallpaper is universal. They cover not only walls, but also doors, creating unimaginable patterns and compositions. In this case, you don’t have to bother with cutting the canvases. However, the door cannot be exposed to moisture. Therefore, this method is unacceptable for decorating a door in a bathroom or kitchen.

To work you will need a dry wallpaper mixture and several spatulas. different sizes, hopper gun, roller, clear varnish, color.

Decorate the door with a mirror

Very unusual decoration doors can be made using mirrors. Such decor will not only attract everyone’s attention, but will also visually expand the space of the room and add light. However, cutting and attaching a classic glass mirror is very inconvenient, fortunately there is an alternative - acrylic panels with amalgam, which has excellent reflectivity.

Acrylic mirrors are available in a wide range color scheme. You can choose any shade you like or several to make mirror panel. Plastic panels do not break, are easy to process and attach to the door, and are light in weight. The cost of mirrored plexiglass is not the lowest, but the quality and aesthetic qualities fully correspond to the stated prices.

Before attaching the mirror plastic to the door, you should carefully level the surface by deepening the heads of the nails, sanding off and covering with putty all the irregularities/recesses.

A deep penetration primer must be applied to the door and the back side of the acrylic sheet. After it dries, the cut panels are secured with double-sided tape and assembly adhesive. For convenience, use mounting suction cups; with their help, it is much easier to carefully glue the panels to the door leaf.

As one of the decoration options, you can consider shaped acrylic mirrors. Such a mirror can be attached in the center of the door or you can purchase several elements and arrange them beautifully. Usually small parts are produced with an adhesive layer already applied.

Even from such a simple material as buckwheat husk, excellent work is obtained. The cost of the material is minimal, but the service life of such a coating, unfortunately, cannot be called too long.

Step 1. Remove the layer of old paint and existing vinyl coating from the door, and eliminate all unevenness with putty.

Step 2. Remove the door from its hinges and place it on the floor/stools/table. We paint the door leaf with dark brown paint. If the door has glass inserts, protect them with masking tape.

Step 3. Thickly coat the dried door with PVA glue, lay out the husks, distributing them with your hands. If necessary, add small gold sparkles.

Step 4. Cover the door with transparent varnish (glossy or matte). It is advisable to apply three layers in order to properly fix the buckwheat on the door leaf.

The beautiful door is ready. To prevent the door from being knocked out general design room, decorate the picture frame in the same way and place the creation on one of the walls.

Decorating the door in vintage style

Vintage is sophistication and sophistication, the beauty of artificially aged things, in harmony with the chic of individual decorative elements. A door in vintage style will become a work of art, an exclusive element of the interior.

For decoration you will need:

We will combine painting the door with the decoupage technique and in addition we will add decorative elements. We will carry out the work on a door that has already been removed from its hinges, puttied and carefully sanded, and laid horizontally.

Step 1. Paint the door with white acrylic paint. Apply the paint with a wide brush with stiff bristles in one direction, in a thin layer.

Step 2. When the paint has dried, carefully sand it with coarse sandpaper, achieving an “antique” effect.

Step 3. We begin decorating the panels or the central part of the door. We tear music books and old newspapers into small pieces with our hands. Draw a rectangular or square activity field on the door with a pencil. Lubricate the outlined areas with PVA glue. Immediately lay out the paper chaotically, smoothing it with your hands. Apply clear varnish in two layers on top.

Step 4. Along the perimeter of the areas covered with paper, we attach a black baguette with mounting glue.

Additionally, the door can be decorated with a beautiful wreath, a large lace bow or plastic beads imitating pearls (adhesive-based).

There are many other ways to decorate doors. Operate with what is available in your home arsenal materials, use your imagination and create your own masterpieces.

Video - A variety of ideas for decorating doors

Video - Applying patina to a door

Video - Decorating the door yourself

When conducting repair work In a home, owners are often faced with the need to update many products and systems. First of all, this applies to entrance and interior doors.

For some things, only a replacement is suitable, while for others, it is possible to give new life. They can be restored to their previous appearance if you have the desire and skills to work with them. various instruments. Finishing old or defective surfaces will hide door imperfections and update the interior.

How to decorate a door?

The entrance to the apartment is the hallmark of the home, so it is very important to install a good-quality and beautiful entrance door. It is the first thing that guests who come to the house pay attention to. It is necessary to refine not only the surface of the canvas, but also the frame and fittings. To do this, there are several ways that can quickly and efficiently update the product.

Coloring

This is the most economical option decorating the door structure. In the modern world, it is not at all difficult to find a suitable tone, because there are many different shades produced by many well-known companies. In addition, it is possible to get perfect color by mixing the coloring composition with the color, observing certain proportions.

Acrylic water-based, oil and nitro paints are best suited for painting door structures. Acrylic paints are made using water based, and therefore dry easily and do not have a specific odor. They are absolutely safe for health and have a long-lasting bright color. But nitro paint has a pungent odor, so it is suitable for painting external structures.

Oil paints are used less frequently than the previous ones, since they do not have such high performance qualities, but they can quite cope with painting wooden and metal sheets.

The coloring composition must be applied using a special roller in several layers. Before applying the next layer, be sure to wait until the previous one has dried. You can also paint a pattern on the surface of the door using templates and brushes. This method is suitable for processing doors both outside and inside the apartment.

Pasting

This method is suitable for people who do not want to wait for the canvas to dry. Adhesive film is well used in many areas and helps to decorate almost any product in a short time. It consists of a colored film, an adhesive surface and protective paper, which must be removed before pasting.

Before pasting the door with self-adhesive, it is necessary to prepare the surface. It must be cleaned so that there are no protrusions left on it. It is better to fill various cracks and chips with putty. And just before pasting, dirt is removed from the structure and degreased.

Wood and MDF paneling

Suitable for handmade decoration doorways. Most often, this method uses thin wooden planks, which are attached to the canvas with glue. Subsequently, the tree must be processed. And in order for it to retain its appearance for a long time and not deteriorate after some time, it must be treated with a moisture-repellent composition.

In addition to wood, MDF overlays can be used to decorate the structure. They are also attached with adhesive. Thanks to diversity color solutions material, you can update the door in any style. In addition, such refining looks very impressive.

Facing

For this method, it is possible to use veneer, plastic, laminate and PVC. These materials are applied only when exposed to warm air. At the same time, you need to work very quickly to do everything smoothly and efficiently.

Padding

The least common solution for upgrading door structures. But this way you can achieve a luxurious and attractive look. If you apply upholstery to an old, worn door, you can hide all its defects. In addition, this option helps to insulate the canvas.

Slopes and doorways can be leveled with plaster, tiles, mosaics, upholstery, plastic and wood panels. But the thickness of the lining must be sufficient for the door to open and close freely. Framing the box will allow you to get a new design.

How can you decorate doors beautifully?

You can use many methods and materials to update an old door. For example, it can be sheathed PVC panels, plastic, iron sheet, MDF, wood, laminate, lining, plasterboard, linoleum, eurolining and chipboard. You can cover the box with veneer and update the canvas itself decorative stone, leather or leatherette and even carpet.

All these types of finishes allow you to choose the most suitable material, which will suit both price and performance indicators:

• Door decoration MDF or PVC panels suitable for wooden entrances and metal products. The main advantage of these materials is their low price and lightness. installation work, thanks to which you can update the design in a short time. MDF and PVC panels are good because they are quite durable, safe and easy to maintain. The panels can be covered with natural veneer, a layer of lamination or plastic.

• Door renovation is much easier plasterboard, plastic or metal. Sheets of plasterboard, chipboard and lining are most suitable for covering the slopes of a doorway. Of course, the most available material in this case it is plastic, and the most expensive is natural stone.

Eurolining and PVC lining are available in a wide range of colors and can have any design, which allows you to eliminate finishing. But these materials are extremely unstable to mechanical influences, which cannot be hidden with your own hands.

• The most expensive, but at the same time the most effective material is leather or leatherette, which is also called dermatin. Faux leather can have different characteristics and appearance. For example, it can be smooth, porous and structured, and its wide range of colors allows you to decorate almost any interior. But you need to be extremely careful with such materials and you need to know how to properly upholster a door with them.

• Door trim has become increasingly used siding, since it is suitable for both internal and external works. Siding is practical, durable, fire-resistant and easy to maintain. Installation of siding is carried out in the same way as installation of lining.
• More recently, it began to be used to decorate an apartment. clinker tiles, which simulates brickwork. To install it, you must level the surface near it and moisten it. doorway water to seal the cement.

• Finishing laminate used when you want to achieve the look natural massif tree, but this is not possible. This material can imitate solid oak, pine, cedar and others tree species. It is easy to work with, but it is best to use it only for decoration. inside doors, as it exfoliates under the influence of moisture.
• Save cash and achieve extraordinary results Decoupage technique. They resort to it when they want to decorate the design and individualize the apartment. For decoupage, materials such as fabric, newspapers, photographs, appliqués and napkins can be suitable.

Upholstery of metal doors

Facing an iron door can be done in two ways: cheap materials (leatherette, leatherette) and expensive decorative panels:

• For product restoration with dermatin or vinyl leather you only need to use glue. To do this, the edges of the structure are lubricated with an adhesive and foam strips are attached to them. Excess parts can be cut with a special knife. Then the end of the upper part of the door is smeared with glue and the upholstery is glued starting from the top. During operation, be sure to smooth the canvas to avoid the formation of wrinkles.

• To upholster iron door decorative panels First you need to measure it. It is important to know the exact dimensions of the canvas and the width of the inner corners, which will subsequently be covered with sheet foam and wooden beam. Then, on the upper and lower parts of the structure, it is necessary to make a mark on the attached bar. Using a drill, 16 holes for fasteners are made in the canvas, the diameter of which should be identical to the diameter of the self-tapping screws. The bars are fixed on the canvas, after which holes are drilled for attaching a decorative panel.

At the end finishing works you need to make holes in the panel for peephole, locks and handles. Inside metal door We cover it with polystyrene foam, and then attach MDF panels on top.

How to decorate the front door from the inside?

Door design from the side of the apartment it can be decorated differently. The best option is painting, for which you do not have to remove the canvas from its hinges. Surfaces adjacent to the product must be covered with newspapers so as not to stain during staining. All fittings are removed or sealed with tape. The surface of the door is preliminarily sanded, and then treated with a protective impregnation that will protect the wood from moisture. And after complete drying, the structure is covered with a paint and varnish agent in 2-3 layers.

To decorate the veneer, you will have to prepare an iron and a paper sheet. Repair of the canvas begins with removing it from the hinges and taking measurements. Veneer strips are superimposed on the surface of the product so that the pattern matches. It is advisable to number each piece so that there is no confusion in the future.

It is better to glue the veneer from the top, gradually moving down. To do this, remove the protective paper from it and glue it to the canvas. To get rid of the resulting bubbles and folds, a sheet of paper is placed on top of the veneered strips and ironed.

These methods of lining the inside of the product are performed without difficulty. The main thing is to take measurements correctly and do everything carefully.

How to sheathe a street door from the outside?

To finish the door from the outside, it is important to take into account the features of all possible materials. It is important to ensure their strength and durability so that their properties do not change under the influence of the external environment. Moreover, it must be understood that not every material can be used to process the outer or inner part of the structure.

To manually update a box located from the street, you can use:

• Steel sheets. Their structure can be smooth or embossed with an imitation of an interesting pattern. Good steel sheets will protect the room from drafts, but they must have a polymer or cork backing.
• Viniplast. It may consist of fiberboard or PVC. This material is not resistant to sun rays, and therefore it must be coated with a special varnish with an ultraviolet filter.

• Marine plywood looks like natural wood. After installation, it is covered with stain and frost-resistant varnish. If you need to change old plywood, then this process will not take much time and effort.
• Leatherette is a material that is equally suitable for interior and exterior finishing. It is quite easy to install, and it comes in a variety of designs. And its soft structure can hide sharp corners.
• Fake diamond Available in thin panels that are fixed to the outside of the door using construction resin. The structure, lined with stone, looks very impressive.

To reconstruct the street side of the door, it is necessary to use insulation - isolon. The thickness of the isolon can be any - it all depends on personal preference. And for fixing the insulation, staples, sealant or nails are suitable. After that, the canvas itself needs to be decorated.

How to decorate the door with your own hands?

You can clad the door yourself different ways. The most common is wallpapering. Any type of wallpaper, from paper to liquid, is suitable for this method. Before processing with this material, it is necessary to prepare the canvas: remove the paint, putty all the imperfections and sand it. You can cover the entire canvas or just the paneled part with a wallpaper sheet, cutting out parts of suitable size.

The decor can be fabric, which, due to its structure, will make the product unique. But it is necessary to choose a fabric, taking into account the degree of its shrinkage. Multiple fabric sheets can be used different designs.Patchwork technique quite popular among designers: you can cover the entire canvas or just the central part with fabric. The product can be covered with unusual nails, beautiful laces, and baguette frames.

An unusual finishing method is mirror acrylic. Using mirrors you can visually enlarge the space and improve lighting. How to cut it yourself the required part It is not always possible to make it from a mirror; you can purchase a ready-made panel with amalgam. The simplest option is shaped acrylic mirrors. They can be arranged into one whole and cover the entire canvas, or they can be placed in the center, leaving the rest of the space free.

Attach acrylic mirrors to a previously cleaned surface. You need to apply a primer to the back of the mirror sheet and to the door itself, and only then secure the panels using glue. You can resort to mounting suction cups, which will greatly speed up the process.

How to make cash for front doors yourself?

Cashing is an element of decor that completes the design of the entire building. Its purpose is to hide irregularities after installation. entrance structure. With its help, noise insulation is improved and thermal conductivity is reduced.

The cash box should be in the same style as the house, so when choosing it you need to take into account some rules:

• it must be combined with the walls of the building;
• its performance should be top level so that in spite of atmospheric influences it appearance remained unchanged;
• the dimensions of the platbands should be such that they do not get lost against the rest of the background;
• internal cashing may be flat or rounded, and sometimes threaded.

For inter-door space it is better to purchase wooden frames. But they can be replaced with plastic or metal elements. To prevent structural shrinkage, wooden house install a pigtail. The oscillator can be made in four ways: in an embedded block, in a shim monolith, in a tenon with ready-made slope and into the deck.

In order not to select the platbands yourself, you can buy a ready-made kit consisting of canvas, boxes, cash, extensions, hinges and handles. This set will make your job a lot easier.

Dimensions

Regardless of the type of construction, doors have standard sizes that were established by GOST:

• Height standard opening varies from 2.07 m to 2.37 m. The exact parameters are set taking into account the ceiling height and door width.
• The width of the standard design is 90 cm, but this figure may vary depending on the individual parameters of the canvas.
• But the thickness of the doorway can be anything - there are no standards set for it. The thickness of the box is selected taking into account other indicators.
• Not always the dimensions of the doorway meet the standards. In a cottage or private house they can be anything, but within 2 by 2.4 m. It is better not to widen the opening beyond these figures, otherwise it will be very difficult to choose the right door.

By showing your imagination and devoting a little free time, you can create a work of art. Many decorating ideas old door amaze with their originality:

• For example, to create an atmosphere of bohemian celebration, you can use rivets and various beads, which very often lie idle in a box of small items.
• Holes that form unusual patterns can decorate products.
• You can arrange it quite unusually door frame buckwheat This process will take a lot of time, but it will allow you to decorate the room.
• In addition to the door itself, you can decorate the space around it. For this you can use bows, artificial flowers, ribbons and laces.

• A design decorated with wreaths, bouquets, glass inserts and others will give you an unusual sensation. original things. From the entrance side, you can glue a large horseshoe or an improvised nest onto the canvas.
• A door with painted butterflies, flowers, trees or clouds will look quite gentle. It is not necessary to draw out every detail; you can make the drawing in the form of an abstraction.
• You can also draw patterns near the doorway that smoothly flow onto the canvas itself.
• If on own ideas If you don’t have enough imagination, you can watch video lessons and choose a suitable master class.

When restoring an old door, it is important not only to think over its design, but also to update the insulation. Thus, you can get not only a beautiful, but also a warm product.

To learn how to cover a metal door from the inside, see the following video.

Doors age and their appearance becomes less satisfying over time. In most cases, they are replaced or repaired, but few people resort to decoration - effective way make a new one out of an old door.

Let's get started - start with surface preparation

Any door decor begins with preparing the surface; as a rule, old painted doors are decorated with your own hands, on which many defects in painting and material are noticeable. For convenience, the door is removed and laid horizontally. We heat up a layer of old paint with a building hair dryer and remove it with a spatula. If you don't have a hair dryer, you can use chemicals to remove old paint.

Next, apply wood putty, apply it in a thin layer, covering all cracks, depressions, and chips. Let's start sanding the door leaf, for which you will need coarse-grained and fine-grained sandpaper. Hand sanding takes a lot of time and requires a lot of effort. The grinder will help out, the work with which will go much faster. After rough sanding, fill the cavities with putty and repeat sanding.

If you plan to paint the door, you should achieve a perfectly flat surface, otherwise the paint will only highlight all the defects. Other methods of decoration require a flat surface, but not necessarily an ideal one.

Then we remove the dust, wash the door leaf, applying detergent for dishes, diluted with water. The next steps depend on the method chosen for the update. If you plan to use fabric or wallpaper, prime the surface using a special primer or glue diluted to a liquid state. When the primer dries, we proceed to the next stage of work - we apply paint or use another type of decor on the doors.

Decorating with paints - pictures using stencils

A plainly painted door is not very presentable. You can give it a look that is in harmony with the overall interior by performing decorative staining. Drawings are applied to a plain base layer using stencils. It is important that the background comes out evenly colored, without gaps and sagging. Let the paint dry. Only after the base layer has completely dried, we proceed to apply the second. Using a stencil, apply a second coat of paint of a different color.

You can create the drawing yourself, but it’s better to buy a stencil with an ornament or in pictures at a construction hypermarket. The choice should be made on a drawing or ornament that will be in harmony with common style rooms. We apply the paints with a roller or sponge, each subsequent layer after the previous one has completely dried, then they will not mix. The same technique can be used on a door with a large glass insert.

The classic method is wallpapering

To decorate the door you can use the most different wallpapers: regular paper, vinyl, non-woven. The market offers material in a variety of shades and patterns, plus high-quality glue. You can use canvas, or you can decorate individual places with them. If you plan to cover the entire surface, first remove the fittings. In any case, follow some rules.

We apply glue only to the wallpaper, although some people think that by covering both surfaces with glue, we can provide more strong connection. In fact, there will be a lot of excess glue that will have to be removed, which can ruin the wallpaper. To smooth the surface and remove bubbles, we do not use hard objects; we take a special spatula, roller, sponge, rag, and finally, so as not to damage the paper. We cut off the excess from the glued wallpaper with a stationery knife.

It is very beautiful to cover the door in an apartment with photo wallpaper, but not with standard store-bought ones, but made to order. We select any drawing and transfer it to a flash drive, then contact an agency that does photo printing. We indicate the dimensions and print photo wallpapers, including 3D ones. Additionally, we decorate the wallpapered door with moldings, which are foam baseboards or self-adhesive cord.

Liquid wallpaper - creating an exclusive decoration

Liquid wallpaper is a universal material not only for walls, but also for decorating doors, their design and decoration, creating unimaginable patterns and compositions. They are afraid of moisture, so this method is not used for decorating in the kitchen or bathroom. Be sure to thoroughly prepare the surface - treat it with alkyd primer and oil putty. We use a white color so that the base does not show up too much through the wallpaper layer.

Add a little to the dry wallpaper mixture warm water, mix with your hands (it is completely safe for health). After 15 minutes, mix the wallpaper again, add color and mix again until a mixture with a uniform color is formed. 1 cap per 5 liters of wallpaper will give the mixture a pastel shade. The intensity of the color depends on the amount of color. If you want to create a multi-color pattern, prepare wallpaper of different colors in different dishes.

Let the wallpaper mix stand for 12 hours. We take some wallpaper on a spatula, apply it to the door leaf, carefully stretch and smooth it until a thin layer of equal thickness is formed. After a maximum of 3 days, the composition will dry out. We cover it with a transparent varnish, which will prevent rapid abrasion. If something didn’t work out, there is an opportunity to correct the unsatisfactory work and decorate the door in a new way. We wash off the wallpaper layer with warm water and repeat the process.

Fabric decoration - attractive and unusual

A door in a room decorated with fabric looks very attractive and unusual. We pay special attention to the fabric - it is important to find out the degree of its shrinkage. Cut a small rectangular piece, measure its length and width, soak it well in water and dry it. We measure the dried piece again and compare the indicators before and after wetting. If the difference is large, then before using the fabric for decoration, moisten and dry the cut.

Masters use in their work not only a single piece, but also individual fragments having different colors and textures. This method is called “patchwork”; it is often used by designers to decorate not only doors, but also entire rooms. The technique is much more complicated than pasting a whole piece, because the pieces can have different degrees of shrinkage. Glue is better to use casein or CMC, mastics are suitable Gumilax, Bustilat.

We treat the surface of the fabric with an adhesive, apply it to the door leaf, and smooth it with a spatula. When using different pieces in your work, it is important to monitor the joints between them so that they are neat, otherwise the door will look ugly and unkempt. Additionally, but not necessarily, we decorate our masterpiece with foam frames, furniture nails, various laces - leather or shiny nylon.

Restoring a wooden door - vintage style

An old wooden surface has a luxurious look if it is brought into proper condition. This design element belongs to the now very popular vintage style, which is used on any surface. Decoupage doors will revive an old product and breathe new life into it. The picture is combined with wooden elements, and a stylish harmonious design comes out.

Let's give an example of how to restore an entrance door made of natural solid wood in vintage style using decoupage techniques and the use of decorative elements. We carry out the work on a door that has been removed from its hinges, thoroughly puttied, with a perfectly flat surface:

1. 1. Paint the door laid horizontally with acrylic paint white. Apply it with a wide brush in a thin layer in one direction.
2. 2. Let the paint dry completely. We start sanding with coarse sandpaper, as a result of which we achieve the “antique” effect.
3. 3. Using our hands, we tear old newspapers and other paper into pieces. We select and outline the field for decoupage and grease it with PVA glue. Immediately, in no particular order, glue the paper and apply two layers of transparent varnish.
4. 4. For final finishing plot with decorative elements We fence the perimeter with black baguette. Additionally, we decorate with a lace bow, a wreath of artificial flowers, and beads.

Doors can also be decoupaged using special paper, a printed design, or a beautiful paper napkin.

Designer decor - turning a thing into an art object

This is the only way when there is no need for thorough surface preparation, because all defects will be hidden by a unique design. We begin decorating the door by purchasing an egg tray, which will serve as material for papier-mâché. Sprinkle the tray with water and knead it with your fist with the intention of leveling the surface. If the material tears, this is normal, because small pieces are needed.

We glue almost flat pieces absolutely chaotically onto the door leaf to be decorated, using hot melt glue or liquid nails. Then all sorts of unnecessary things are used, preferably unusual ones, original form, but it is possible to use things that are familiar to everyone. We use everything that catches our eye: lids of cans and bottles, keychains, rings, chains, elements children's construction set etc. We paint the finished surface from a spray can with high-quality acrylic silver paint.

Decorating entrance and interior doors with your own hands is an interesting activity that will change the design of your room!

Sections of the article:

Over time, old doors become less attractive and require updating. Not every person can afford to replace old doors with new ones, especially if such a step cannot be justified by urgent need. In most cases, all that is required is repainting or decorating the door, after which the door can begin a new life.

Preparing the door

Even a cracked door leaf can be updated. Do-it-yourself door decor will allow you to update an old door beyond recognition with a minimal investment of money and often using only improvised means. However, before making decoration wooden door, it must be thoroughly prepared.

Sequence of work

The first step is to remove the old coating. This is a prerequisite to ensure maximum strength of the new coating and the removal of many microbes that the old paint has absorbed. After you have removed the door leaf from the hinges, you need to place the door on flat surface and remove the fittings. If there are glass inserts, they must be removed during decoration. To remove old paint, sandpaper or a solvent designed for this purpose can be used. To work with solvent you will need gloves and a respirator. A hair dryer can also be used.

Once the paint is removed, it is necessary to assess the condition of the canvas. If there are cracks or chips, you need to fill them with wood putty. To ensure an even, smooth surface, you need to process it manually using sandpaper or grinder. Wood should not be wetted! You need to wipe the surface of the door with a slightly damp cloth and treat it with an antiseptic.

In order to preserve the natural texture of the wood, it is necessary to apply several layers of varnish. If you cover the canvas with stain, the tone will be a little darker. Thus, you can turn pine into cherry (a kind of imitation of noble species), while the natural beauty and naturalness of the material are preserved. If the door is not repainted, as soon as the antiseptic has dried, the surface will need to be covered with two layers of primer.

Selection of decor options

There are many ways to decorate and update a door. Even without any artistic skills, you can turn some of your ideas into reality.

The easiest way to decorate an old door is to repaint the door new paint. In today's market building materials In addition to the usual enamel, there is a large selection of various colors.

The most optimal one given time an option on how to decorate an old door yourself - application acrylic paints. When using them, you will definitely be convinced of the convenience of working with them, the absence of smell, wide color palette. For painting doors, you can use not one color, but several - the main thing is to combine them correctly so that the result is only pleasing.

Alternatively, you can use latex paint that is resistant to water to decorate the door. This option is more suitable for doors to the bathroom and nursery. Latex paint odorless, the drying speed is very fast, as a result, the whole job can be done in about an hour. By painting the door to the children's room, you can attract the children themselves and come up with a unique design with them.

Using stencils

Even if you are not a professional artist, you can use a variety of stencils to create a beautiful interior door. Using them is quite simple: you just need to attach the stencil to the door and apply paint. As soon as the paint has dried, the stencil should be carefully peeled off from the door leaf.

And if you have the skills of a painter and artist, you can get an incredibly attractive drawing. If the resulting pattern does not suit you in some way, you can always fix it - repaint it again.

If you want to get the effect of wood or an antique object, you can use some available tools: a sponge to create stains on the surface, steel wool to imitate an antique surface, a stiff brush for a jeans effect. There are also special paints on sale that can be used to imitate denim.

Using Film

An equally simple way to decorate doors with your own hands is to use vinyl film. However, this method is only applicable to canvases that are in good condition. It will help complement the interior of the room bright colors. Simply select the desired option and transfer self-adhesive film on the door. Despite the minimum time spent, the result will please you for a long time.

Ready-made stickers are commercially available in many construction stores. If you want to make some kind of pattern from films, you can purchase self-adhesive PVC film after making a cardboard template. Now you need to transfer the contours of the template onto the film, cut out the decorative elements and glue them to the door.

Application of moldings

Get original decorative finishing moldings will help. Using them, you can create an imitation of stucco - great option, combined with classic interior, antiquity. Moldings are special elements made of polyurethane or foam. Fixation on the doors is carried out with glue, which is liquid nails. With the help of moldings, any composition of door decor is possible, but it is necessary to take into account the limitations of its shape. For sliding doors This decor option is not suitable.

Mosaic decor

Do-it-yourself door decor using mosaics is quite rare and unusual. Due to its heaviness, ceramics are not suitable for every door, so mosaics are used much more often.

To decorate a door, it is better to insert mosaics in fragments. This method will provide an original and bright look. Such finishing will not lead to a significant increase in the weight and thickness of the canvas. If the products are made of glass, you must purchase tile adhesive of a special white color. Better yet, use transparent resin or liquid glass.

Stained glass for decorating doors

Decorating doors with glass inserts is an excellent option for decoration. Best option– decorate the canvas with your own hands; stores offer ready-made glass covered with film, metal inserts or glass with a pattern. Currently, the most popular method of painting glass is using acrylic paints, as well as creating stained glass yourself.

If you choose the latter option, you will need to acquire a decorative mastic-contour to create an imitation metal frame. To ensure uniform distribution of paint over the surface of the glass, work with stained glass windows must be done in the “horizontal” position. As soon as the stained glass window is dry, we insert it into the panel and secure it with glazing beads.

Decoupage

Thanks to decoupage, it is possible to create an attractive door design without much investment. To decorate an old door using a similar technique, you only need napkins with the desired pattern, 200 ml PVA glue, a brush (preferably made of natural bristles) and acrylic varnish.

The canvas must be prepared - primed and painted in the desired color. Once the paint has dried, you can start decorating. From the napkins, we separate the layer on which the design is depicted and tear it lengthwise into two parts.

We tear the napkins with the image lengthwise into three strips. The edge should be slightly uneven. We put aside the strips with smooth edges for now. We tear the middle part of the napkin into squares with sides of about 3-4 centimeters.

In a small container, dilute PVA glue in water. The proportions should be approximately 50/50. Let's start decorating.

Apply a strip with one straight edge to the area to be decorated. Using a brush dipped in glue, smooth out the fragments. The resulting folds provide the texture of the finish. When working, it is necessary to take into account that wet wipes are quite elastic and delicate.

You need to work carefully with a brush dipped in glue. Step by step we create a frame with one straight edge and the other with a torn edge. We fill the middle of the frame with squares from napkins in the same way.

DIY door decor is almost complete. If you have any difficulties, refer to the photo in our article. Leave the finished surface to dry. After about a day we cover the decor acrylic varnish. The varnish must be water-based, then it has no odor. With a minimum cost of materials, we get a beautiful door surface.