In this article we will talk about the manufacturing technology of those tools that are extremely necessary to have in the house. They are used not only during various plumbing or carpentry work, but also for domestic purposes.
Industrial vices are a fairly simple design from an engineering point of view; the manufacturing technology is also not classified as complex. But companies sell them at a fairly high price, the only real explanation for this situation is the desire to make maximum profits.
We'll tell you how to make it at home functional tool With minimal losses time.
As for materials, the vast majority can be found at scrap metal collection points. Accordingly, their cost approaches zero.
Step 1. Clamp a piece of thick-walled pipe (thickness is not less thanits 4mm, diameter 150mm andlength 100mm) and a grinder with a discabout metal, cut it into two clear halves.
A little lower in this article we will tell you how to make a simple device for finding the center of round workpieces.This is very important point for the vices we manufacture, if this is not done, additional loads will occur during use.They reduce the compression force and increase risks of mechanical breakdowns vice
Step 2. Prepare reinforced curtains. In time squeezing the lips on them there are significant efforts, in stores T There are no such durable models. Veils are manufactured in several stages.
- Cut off the metal tube her the length should be equal to the length of the cut large one. Tube diameter not less than 10 mm, wall thickness≥ 1mm.
- Divide the tube into 5– 6 parts, each about a centimeter long, the specific quantity depends of the total width of the vice.Cut carefully, all planes must be made only at an angle of 90°, otherwise the hinges will not work correctly and the jaws will jam when opening/closing.Place the curtains on the metal axlerelevant sizes.
- Weld them to the pipe. For this then clamp the workpiece in a vice andaccurately align the position of the halves.
At first weights need to be fixed on each side ovate through one, the seams must be very strong, control the quality, eliminate gaps.
Sutures should be placed on both sides , after boiling the first, remove the workpiece, open it and secure the bushings on the back side.
- Clean workpieces from rust and prepare them for painting.
Step 3. Make sponges. To do this, from a piece of sheet steel should cut out the elements to the appropriate sizes.
Steel thickness is not mless than 10 mm – spongesthey must have enough private strength. To reduce the coefficientslip point buse a grinder to cut strips on them s in the form of a grid.
Step 4. Make two hinges for lips vice. What are they needed for? The fact is that in industrial with kah lips ki move in a straight line , their planes are always about with t are parallel, and in our case when tightenedwhen one of them moves with me in an arc, depending on the race until completely closed, the angle of inclination between them is mgetting married. To lips ki always at the moment of clamping relied in parallel, one of them was wife have the opportunity n Ability to adjust along the axis(swim) . The hinges are manufactured following blowing way.
- Select a strip of sheet th steel thickness ≈1 mm, length ≈ 50mm, width ≈ 20 mm.
- Installed in the center wite metal at x axis Ø 5mm, the same rods must be placed on both and m st about ronam.
- Insert into a vice and squeeze it until it stops. Behind With Even after such inserts the sheet will bend.
- Cut the strip in half and cut off two hinges.
Step 5. Attach the hinges to one of the jaws. To do this, first weld on both sides axis along the perimeter of the circle, clean the seams. Zat We need to install the axles on the GU bku vice and smooth weld the platforms to it. Again, remove metal stains, cut off excess pieces rods Collect together all the details and check their performance.
At this point, the preparation of the movable jaws is completed; we need to proceed to the clamping mechanism.
Prices for angle grinders (grinders)
Angle grinders (grinders)
MadeVltionmechanismclamp
This node is much more complex than the one described above. Done adaptation and3 sheets thickness ≈ 5mm, length 170mm, width 130 mm.
Step 1. On the plate, measure two points for drilling holes for the components.
They are located along the axis of symmetry, one at a distance of 70 mm from the edge, the second 25 mm. Take your time, mark with maximum accuracy, every mistake is considered critical th and is not corrected.There will have to be a foundation under mechanism completely redo.
Step 2. Carefully drill holes, drill diameter 4mm.
Between them cut a straight groove.Its width should be slightly larger than the thickness of the plate that subsequently slides in it.
Step 3. Drill two holes in a square, betweenwe also need to cut a groove, dThe length corresponds to the width of the inserted plate.Two such plates are required.
Sawing a through groove
Step 4. Put all the elements together.
Put it on flat surface square, the base of the clamping device on it and a second square on top. In the slots, place the prepared plate with a hole at the top end. Weldinggrab the parts, then assemble them in the vice in reverse order and firmly weld the protruding plate with the hole to the bottom square.
Turn the structure over again and apply welds on this side. You have a debtwives get a mobile unit:two squares slide along the base plate of the mechanism, and a part with a hole is welded to them.
Using a cylindrical grinder, thoroughly clean the seams and, if necessary, strengthen weak points.
Step 5. Prepare another part, the so-called thrust plate. The length is equal to the width of the base of the clamping mechanism, the width is approximately 3 cm. A hole must be made in the center for the clamping bolt.Now you should start assembling the elements.
Step 6. Prepare two ears with holes, each 25mm long, hole diameter 8mm.
Install them on the movable plate of the mechanism on both sides and connect with a bolt.Do not tighten the nut too much, elements must be able swing around an axis.
Step 7. Place the movable jaws close to the parts and weld the knots together.
Watch out so that all axes are parallel or perpendicular depending on the purpose and location of the elements. You should already have an idea of how a vice works, this will help you choose correct positions each element.Weld the parts tightly.After cleaning the seams, assemble the vice onto the bolt, again do not tighten too much.
Step 8. Now start making fixed vice assembly. It will require several details:
- two 40x20mm;
- two for the wall 25×20mm;
Metal thickness 2 mm, hole diameter is selecteddepending on the size of the bolt, in our case 6 mm.
WITH pick up the elements: first put on the bolt n b those short ear, then two long ones, and then another short one.
Step 9. Place the long ears at the edge of the clamping mechanism, placing them exactly along the axis of symmetry.Weld them firmly.
Step 10. Mark the location where the vice halves are secured to the short lugs. Fix the elements, disassemble the vice, strengthen all welds.
Step 11. Make a support platform for the screw. For these purposes, it is recommended to use a nut of appropriate thickness. It's welded to the movable square with back side . Weld seam, like Always , is applied around the entire perimeter of the parts. Check slave performance and smoothness, P When tightening/unscrewing the screw, the movement of the parts should be easy and without any jamming. If there are problems, then we need to find and fix them reason. It can be hangnails, metal leaks, slight nervousness.
The vice is completely ready. Paint their surfaces with special paint and after it dries, you can use the tool you made with your own hands.
Prices for popular brands of portable welding machines
Portable welding machine
Video - DIY channel vice
Center Determinant
The need to find The concept of round parts appears almost always, when for the manufacture of various crafts round blanks are used. To make a fixture school wooden triangle and metal triangle are used protractor.
But this is optional, You can use other blanks, the main thing is that one has a right angle, and the second an even strip.
Step 1. Using a pencil, continue the length of the legs along the hypotenuse.
Use a hacksaw to saw off excess pieces, and clean the cut areas with a file or sandpaper.
Important.Make sure that the inner lines of the legs are perfectly straight, otherwise the center is determined incorrectly.
The part may rest against a protrusion or fall into a recess,in this positionit is impossible to accurately draw diameters, and the center of the circle automatically shifts to one or another station O Ron. In the manufacture of some devices errors can be critical. It is strongly recommended to check the specified requirements with a new triangle after sawing.
Step 2. Cut a semicircular scale from the protractor; for further work you will only need an even strip.
The protractor is made from aluminum alloy 0.3 mm thick, it can be cut without problems with ordinary household scissors.Remove burrs with a file; they are very sharp and can injure your hands when using the device.
Step 3. Install aluminum stripe strictly along the bisector of the triangle.
Bisector – a line dividing an angle exactly in half.We have an angle of 90°, which means that the bisector should be located at an angle of 45°. It's easy to find.Insert the second isosceles right triangle into the workpiece so that its hypotenuse lies on the leg. In equilateral right triangles, the angle between the legs and the hypotenuse is 45°, and this is exactly what we needed to find.
Step 4. Closely attach the prepared aluminum strip to the leg of the inserted triangle, aligning it exactly. It is necessary to achieve such a position that one of its edges passes along the corner of the cut one. Thin pencil draw a line.
Step 5. Mark drilling points holes They are required at least three, two do not guarantee reliable fixation strength, which causes the element to move. As a result - errors in center definitions.
Holes can be drilled with a drill or a screwdriver with a drill bit up to 1mm in diameter. No electric tools- no problem. The aluminum alloy is so soft that holes can be poked with the tip of an ordinary nail. As always , after drilling with a file it is necessary take off sharp hangnails. Same holes need to be done in wooden parts as well devices
Step 6. Use small screws to connect the elements into one design Small screws required (great for desktop computer mounts), too large ones will split the thin strip of the triangle.
Practical advice.During connection, constantly monitor the position of the strip, place the second triangle and navigate along the planes.
First, it is recommended to tighten one screw a little, check the position, then second Roy. A little againcorrect. Everything is normal - you can tighten them all the way and install the third one. Use your fingers to press the aluminum strip very firmly against the wooden slats, when twisted, it can change its position. After fixing, you need to check the bisector again.
Assembling the fixture
Step7 . Using scissors, cut off the part protruding beyond the perimeter of the trianglestripes, hangnails grind it down.
Step 8. Remove sharp ones ends of the screws, work with a file carefully, do not allow the connections to loosen.
Step 9 For improvement appearance paint determinant center. Choose your paint carefully.The fact is that part of the device is wooden and part is metal; you need to use only wear-resistant universal paint. Before applying it, it is imperative to degrease the aluminum part. Wipe its surfaces with purified gasoline, acetone or another chemical solvent. Paint can be applied only after the liquid has completely dried.
This is the manufacturing process finished, ready to use device as intended. How exactly is this done?
- Paste There is a round piece between the legs of the device. Press it down, it should touch everyone at one point.
- Turn the device with the reverse side and along the bisector line draw a line.
- Turn the part a little and repeat follow the above steps. The center of the circle is located at the intersection of the two lines.
We explained the principle manufacturing of fixtures. If you intend to work with large diameter workpieces, t o length t ov should increase.It is not necessary to use factory triangles, you can make them any sizes with my own hands.
On our website you will find a lot of interesting things. For example, detailed manufacturing instructions, as well as answers to current issues: what types of boxes are divided into and what are their advantages? Tips for making a screen for a heating radiator from experienced craftsmen.
It's nice to see when a person made everything and other household items with his own hands. To simplify the process of cutting metal or sawing elements from wood, they build homemade machines and accessories for the home workshop. This solution saves not only time on manufacturing products, but also money on purchasing ready-made ones. Several practical and interesting options Let's look at it below.
DIY pipe bending machine
Read in the article
How to use homemade machines and tools for your home workshop
The use of homemade machines and devices for the home workshop is aimed at solving several problems:
- Simplifying the metal processing process. When creating household items, a metal cutter or press is often required.
- Improving wood processing. Even to build small shed or make it wooden, others are needed.
Buy ready-made tool quite expensive, so the use of homemade machines and devices for the garage is becoming more and more relevant every day. Among the most common options home tool highlight:
- carpentry workbench;
- device for quickly sharpening knives;
- device for sharpening metal drills;
- drilling machines;
- press;
- cutting disc machines.
Here are a few photos of do-it-yourself tools and devices from “homemade” people:
1 of 4
Practical DIY tool shelves
Before creating devices and with your own hands, determine the storage location of all devices, so that later you do not have to search throughout the workshop or where everything is. It’s not difficult to make a shelf for tools with your own hands; the main thing is to decide on its dimensions and material of manufacture.
The easiest way to make shelves is to assemble them from wood. Do not forget about the need to coat the finished structure with a protective varnish or to prevent rotting and swelling of the wood.
You can create a combined version from a metal support and wooden shelves. Here detailed instructions to create such a homemade model:
| Image | Sequencing |
 | Assembling the frame. To do this, prepare two side frames consisting of 4 corners. Connect the elements using . Then, tighten the 2 frames together using 4 corners. |
 | When the frame is completely assembled, proceed to making the shelves. They can be made from wood or metal, as well as from other dense materials at hand. It is enough to cut the canvases of a suitable size and attach them to a metal base. |
 | If desired, you can make the rack movable by attaching four small wheels. Or install it firmly in a designated space in the garage. |
You can find others interesting projects and drawings for making tool shelves. Watch the video on the topic:
And also make useful devices for yourself with your own hands. household:
1 of 4
We make a carpentry workbench with our own hands according to the drawings: video instructions and photo examples
Among the common do-it-yourself devices is a workbench. Durable and dimensional, allowing you to securely fasten the workpiece, useful for high-quality cutting of wood and creating various elements from it.
The device package includes:
- Working surface. Hard is used for it to increase the service life of the device. The thickness must be at least 6 cm.
- Supports. Collected from wooden beams or metal plates. The main task is to ensure the stability of the entire mechanism.
- Vise for securing the product. If the table is long, you can install two vices at once.
- Tool box. Useful recess or retractable design, providing quick access to necessary small parts.
To assemble a carpentry workbench for your workshop yourself, you should choose a drawing and purchase materials for the work.
DIY carpentry workbench drawings
Before purchasing materials to assemble your own workbench, you should think about a detailed drawing. It should include the dimensions of the machine itself; it is advisable to note the dimensions of the materials used and their quantity.
For example, finished drawing A DIY folding workbench may look like this:
Whatever model you choose to create, take into account several features of the workbench that ensure ease of cutting wood:
- height and length of the master’s arms: the height and width of the tabletop depend on these parameters;
- which hand is working: place the vice on the right or left;
- what blanks will be made: choosing the shape of the table;
- how much space in the room do you allocate for the workbench?
Taking into account all these parameters, it will be easier for you to decide on the drawings of the carpentry workbench and the dimensions of the machine. Here are a few interesting examples:
Instructions for assembling a wooden workbench with your own hands
You can buy a wooden workbench in a store or through online catalogs, but it’s cheaper to make it yourself. Let's take as a basis a simple option with standard sizes tabletops: length – 150-200 cm, width 70-120 cm.
The manufacturing work will include several stages:
| Image | What need to do |
 | Make the top cover from thick ones to make a shield with a width of 70 to 200 cm. Fasten the elements with long nails, and you need to drive them in from the outside and carefully bend them from the inside. The working surface of the workbench is made only of wood or. |
 | Sheathe the lid along the lower perimeter with a 5 by 5 cm beam. This will make it more convenient to attach the vertical supports. The location of the supports depends on the size of the tabletop. It is better to make them from thick rectangular timber at least 120 by 120 mm. |
 | The carpentry workbench must be installed correctly. Be sure to secure it firmly. If it will be mounted outdoors under a canopy, dig holes for supports. Indoors, use other fastening methods. |
When the structure is assembled, install a vice on it. To fully understand how to assemble a carpentry workbench with your own hands, watch the video:
Making a carpenter's vice for a workbench with your own hands
Professional “homemade workers” assemble not only tables for work, but also vices with their own hands according to drawings. Any design of such a clamp will include several elements:
- Supports, where each one has a sponge for clamping.
- Moving jaw.
- Metal guides. The sponge moves over them.
- Lead screw for moving elements.
- Collar. Necessary for rotating the screw.
When making a homemade vice with your own hands, you can use various available materials. For example, there is a design option from profile pipe. To do this, prepare several pieces of pipe different sizes, steel stud with coarse thread and double nuts.
Instructions for creating a bench vise from a profile pipe:
| Image | What need to do |
 | The largest pipe acts as a body. Supports are soldered to it from below. A 3-4 mm steel flange is put on the back side. A hole is drilled in the center for running nuts, and opposite the front support there is a rear sponge. |
 | There is a front steel flange on the internal moving part. A stud is mounted in it, with lock nuts attached to it. Thrust washers are placed on both sides of the flange. The last element is a movable tube attached to the front jaw. |
And also watch the video “do-it-yourself vice at home”:
DIY metal workbench drawings
A metal workbench does not differ much from a carpenter's workbench. The base is hard metal, not wooden frame. A vice is attached to it, and the entire workbench is designed to withstand the force of a sledgehammer.
Do-it-yourself metal workbenches can have one, two or three cabinets, and also not have shelves and drawers for small parts. In terms of strength for working in a garage, you can make regular table made of metal up to 5 mm thick and reinforced structure, where sheets from 10 to 30 mm are applicable.
Here are some useful drawings for making metal workbench for your workshop:
How to make a device for sharpening knives with your own hands: drawings and photo examples
No home is complete without a knife in the kitchen. It is quite difficult to do it correctly without special devices: it is necessary to comply desired angle and achieve perfect sharpness blades.
For each knife, a certain sharpening angle must be observed:
- A razor and scalpel require an angle of 10-15⁰.
- Knife for cutting bakery products – 15-20⁰.
- Classic multifunctional knives – 25-30⁰.
- For hunting and hiking, take a device with a blade angle from 25 to 30⁰.
- If you want to cut hard materials, then sharpen at an angle of 30-40⁰.
To ensure the desired angle, it is worth buying or making a sharpening device. For example, you can assemble a sharpener with your own hands.
A comment
Tool selection specialist at VseInstruments.ru
Ask a Question“If you don’t use sharpening every day, then 1000 rpm is enough for a high-quality result and a long service life of the device.
"To assemble such a machine, you will need a motor from a washing machine with a power of 200 W. Completely for creating a sharpener from an engine from the The progress of work on creating such a simple device will be as follows:
- Sand the wood blocks sandpaper, removing burrs. Make markings depending on the desired angle.
- Attach a stone to the drawn line to give the blade a sharp edge. To do this, attach it to the block and mark its width. Then, make cuts on the markings, up to 1.5 cm deep.
- Attach abrasive stones to the resulting recesses so that the grooves coincide. Then, install the sharpening stone by screwing it onto the bolts.
There are many ways to make a homemade knife sharpener. Choose the one that suits you and try to create a convenient and useful tool for your home.
How to make a device for sharpening a metal drill with your own hands
They make their own not only a sharpener for blades, but also a machine for sharpening drills for metal. Here are a few drawings useful for work:
Ready home machine The simplest and most common version of such equipment for a garage is a converted drill. To work you will need: - base frame;
- rotation mechanism;
- vertical stand.
For the rack, they usually use either boards. The drill is lightweight, so there is no need to use metal. In this case, the frame must be made massive in order to reduce vibrations during operation of the device.
To properly connect the frame and vertical stand, and also assemble all the equipment into one whole machine, pay attention to the video instructions:
DIY drawings with dimensions for a drilling machine
To correctly make any machine or practical device for private use, you should first make a drawing with dimensions. Only then begin preparing materials and assembling the device.
Here are some examples of do-it-yourself drilling machine drawings from a drill:
You can also make homemade vices for drilling machine. Below is a video instruction for assembling such a device:
Article
Living in your own country house You often notice that something needs to be repaired, something needs to be modernized to improve the comfort of living in it. This means that you need to do something with your own hands. Moreover, you have to solve different problems, then become a carpenter, now a mechanic, now a plumber, now a stove maker or a painter. The volume of work can be such that it is impossible to cope with it with bare hands. There is no doubt that the hands and head are the main tools, but they require convenient, reliable and silent assistants. Therefore, every master should have an arsenal of necessary tools to solve these problems. It should include the necessary set of tools without which it is impossible to do serious work and be replenished only with those that are needed to ensure more high performance work or increases its comfort. Let's define this minimum required For different types works
In my opinion, the minimum set of tools for carpentry includes the following tools:
1-metal plane; 2-small plane; 3-screwdrivers; 4-clamps; 5-hacksaw for wood; 6-hacksaw combination; 7-hammer; 8-hand drill; 9-chisel; 10-roulette; 11-miter box with saw; 12-glass cutter; 13-stapler; 14 construction knife; 15-Fclamp; 16-wood plane; 17-axe; 18-sledgehammer; 19-nail puller; Level 20.
The minimum set of tools for metalwork includes:
1-vise; 2-fold workbench; 3-metre assembly tool; 4-hacksaw for metal; 5-pincers; 6-metal scissors; 7-pliers; 8-pliers; 9-nippers; 10-files; 11-files.
The minimum set of tools for plumbing work includes:
1-lever key; 2-universal changeover key; 3-adjustable wrench; 4-knife for plastic pipes.
The set of stove-maker tools required for work includes:
1-hammer-pick; 2-trowels; 3-trowel; 4-level; 5-plumb; 6-laser level; 7-building cord; 8-mall; 9-rule.
A small comment — Until there were laser devices, all stove-makers used a level and a plumb line when working. Laser level allows you to quickly and clearly determine the vertical and horizontal, which is very convenient when laying a stove, but it tires the eyes. Therefore, I used it only during the initial installation and periodic monitoring.
The painting tools required for the job include:
Painting tool1-handbrake hands; 2-maklovitsa; 3-panel brushes; 4-flute brushes; 5-radiator brushes; 6-painting spatula; 7-plastic spatula; 8-spatula scraper; 9-rubber spatula; 10-tooth spatula; 11-angle spatula; 12-mini roller; 13-universal roller; 14-window roller.
A comment — hand painting brushes (handbrake brushes) - These are fairly small brushes, usually with a wooden handle. A brush with adhesive attachment of the beam is intended mainly for working with oil paints. Brush with metal fastening beam, you can work with almost any painting compositions. Maklovitsy Designed for large-scale painting work. File brushes intended for painting only hard to reach places, bringing out fine lines, or stretching out narrow stripes. Flute paint brushes are mainly intended for finishing, that is, to smooth out marks from the handbrake. This operation is called “fluting”, hence the name of the brush. It can also be used when painting surfaces if a high-quality, glossy surface is required. Radiator brushes Designed for hard-to-reach places, such as internal sides heating radiators. U notched trowel the main thing is the size of the teeth, which is determined based on the operation in which it is used. The largest teeth are for working with plasterboard or porcelain tiles, the smaller ones are for tiles, and the very small ones are for working with synthetic adhesives that are used for laying carpet, linoleum, etc.
Speaking of carpet. There are troubles and something dirty is poured onto the carpet or something sticky is spilled. In this case, carpet dry cleaning will help. Sometimes there is simply no other way to deal with contamination without dismantling the coating.
The remaining tools do not require any comments in my opinion.
Finally the necessary power tools:
Power tools1-electric jigsaw;; 2-electric planer; 3-impact drill; 4-punch; 5-screwdriver; 6-circular; 7 chain saw; 8-Bulgarian.
The given list of tools is not dogma. Everyone forms their own arsenal of assistants independently, based on their needs and capabilities.
- DIY gift for Valentine's Day. (0)
A book for your loved one - 55 reasons. Gift idea for February 14th. Anyone can give a gift on February 14 with their […]
To work around the house or in the garage, you need professional tools. But in some cases it is more expedient to make the equipment yourself. As a basis, you can take factory models adapted for performing a specific type of work in the workshop.
Metal processing machines
The most popular are machines and equipment for processing metal products. They are used not only for manufacturing and repair, but also during the maintenance of other tools.
Besides hand tools To complete the repair base of a private garage or workshop, you will need mini-machines various types made with your own hands. We are not talking about professional factory equipment, but about its analogue of lower productivity. However, despite this, it must have an optimal set of functions to carry out all types of work.
Grinding equipment
Grinding equipment is considered an essential machine tool. It is intended for processing metal surfaces- sharpening, grinding, polishing.
To make it yourself you will need a minimum of tools and components. The design consists of a power unit (electric motor) and grinding stones. The optimal option for the machine is to have a double-sided shaft. This will allow you to install two grinding wheels for different types of processing.
Components for the manufacture of mini-equipment for the garage:
- electric motor with power from 0.8 to 1.5 kW. The optimal speed is 800 rpm;
- base. This can be a factory-made frame or one made independently. It is important that it ensures the stability of the structure;
- emery fastening block. Grinding wheels can be mounted on the motor shaft or in a separate unit.
It is important to choose the right types of emery and other equipment. For sharpening tools made from special grades of steel, corundum or diamond wheels are most often used.
For stability, the homemade structure must have mounting elements with which the sharpening machine will be mounted on the work table.
Milling (drilling) machine for metal
Another type of work is drilling holes on the surface of metal products. To perform this you will need a milling machine. As a basis, you can take a drawing of a factory model, which is later adapted for manufacturing with your own hands in the workshop.
Since the device will perform a number of specific functions, it is recommended to think about the layout of the tool. Most often, an electric drill is chosen as the power unit. It is installed on a removable mounting element and, if necessary, can be quickly dismantled to perform other work.
- The steering rack can be used as a lifting mechanism. According to its dimensions, the remaining components of the equipment are calculated;
- do to increase functionality. After securing the part to it, it will be able to move relative to the cutting part;
- Additionally, you can install a corner milling drilling mechanism.
If you need to drill thick workpieces using the machine described above, it is best to use a powerful electric motor instead of a drill. Then a torque transmission unit must be installed.
Some manufacturers offer a router table with a support stand specifically designed for mounting a drill.
Homemade woodworking machines
Three types of machines are needed for woodworking: cutting, grinding and turning. If they are available, you can carry out all types of work at home. However, it should be taken into account design differences, characteristic for each type of equipment.
Before choosing the optimal model, you should decide on the type of work to be performed. The parameters of the future design are influenced by the size of the workpiece, the required degree of processing, and the type of wood. The best option the tool will be made universal tool with your own hands, based on the analysis performed and the dimensions of the space in the workshop.
Wood cutting machines
The most simple model mini-cutting equipment for wood processing - electric or chainsaw. With its help you can make cuts of varying precision and configuration. However, due to the relatively heavy physical exertion, work time will be limited. Therefore, for processing large volumes of wood, it is recommended to make sawmills with your own hands.
Such machines can be of several types:
- disk The simplest version of the device, consisting of a support table, a cutting disk and a power unit. Can be used for cutting sheet materials, bars and boards;
- . Designed for processing trunks. Used for forming boards and beams. They are distinguished by relatively low manufacturing complexity;
- band sawmill. Has the same functions as chainsaw designs. The difference lies in the speed of processing the log.
For curved cutting, you can use jigsaws. However, making this tool with your own hands will be problematic.
During production homemade sawmill should be considered maximum size logs - trunk diameter and length. Based on this it is calculated optimal size and characteristics of the device.
Sanding equipment for wood processing
To sand wood, you can use homemade machines similar to devices for processing metals. The difference will be in the abrasive material, as well as the processing area.
The simplest model of the device consists of a work table, a motor and a vertical grinding shaft. The latter may have a blade or mounting elements for installing an abrasive tape. Using this equipment, you can process the end edges of wooden workpieces and sand them.
The video shows the optimal set of tools for DIY housework:
Examples of machine drawings
DIY making various crafts, furniture, do-it-yourself repair cars are popular not only because of the innate ability of our people to create. This is also a good saving for the family budget.
However, such a hobby requires special equipment. Every home has basic hand tools, including electric ones. Drill, screwdriver, grinder, manual Circular Saw, jigsaw.
These devices make work easier home handyman, but with their help it is impossible to perform work professionally. The home workshop should be equipped with compact machines.
Review of homemade machines for the home workshop - video
Such equipment is offered in abundance by specialized stores.
Having equipped workplace With such an arsenal, you can make anything you want. But the high cost of the tool negates the savings in the production of crafts.
There is only one thing left - to make the machines yourself. Homemade equipment can work no worse than the factory one. In addition, constructive know-how can be contributed to expand capabilities.
Homemade machines for a home woodworking workshop
Wood lathe
It can be made from existing tools. Enough strong table, or just a massive board mounted on legs. This will be the stand.
A clamping spindle is not necessary for wooden workpieces. As well as a separate drive motor. There is a simple comprehensive solution- electric drill.
If there is a speed controller - generally great. Fixed in the cartridge feather drill on wood. It needs to be modified: sharpen the working edge in the form of a trident.
The next required element is the tailstock. In metal lathes, it is necessary to support long blanks. When processing wood on a machine without a clamping spindle, the tailstock is a locking element. She presses the blank against the trident and supports it on the axis of rotation.
Typical tailstock design in the illustration. 
The cutter in such a machine is not fixed in the support. Wooden blanks are processed with a hand chisel, which rests on a tool rest.
Homemade wood milling machines
The complexity of the tool depends on the type of work performed. For basic end processing, it is enough to simply install a hand router under a flat tabletop. The power tool is mounted upside down, the working attachment protrudes above the surface. Such homemade machines are widespread among home craftsmen.
Important! Industrial tools are designed and built with safety measures in mind. A rotating router can cause serious injury, so the mounting must be secure and the processing area must be protected from the operator's limbs.
If the bracket is for hand router equip it with a height change device, you will receive semi-professional equipment.
There are also more complex designs. If you install a reliable hanger for a hand router, you will be able to perform complex shaped processing, including using templates. 
Homemade drilling machines. Eat convenient devices for drills that turn hand tools into stationary equipment. But such racks again cost money. 
Such devices are easy to make with your own hands. One option is to use guides for furniture drawers. In a drilling machine, the main task is to ensure the rectilinear movement of the chuck along the axis of rotation.
The simplest machine is a guide device, and movement is carried out without additional levers.
With one hand, the machine is pressed against the workpiece, and with the other, the drill is lowered along the guides. These homemade machines are suitable for working with wood. To process thick metal, you will need heavier equipment.
How to make a homemade drilling machine, watch this video
Our “Kulibins” have learned to use steering racks from Zhiguli cars as a drilling machine mechanism. You can use a hand drill if you attach a clamp clamp to the steering arm mounting points.
If you need a truly powerful machine, you will have to use a separate electric motor. The same steering rack is taken as the basis, only instead of a clamp and a hand drill, a frame with a chuck, a belt drive, and powerful engine. The power plant can be taken from the old one washing machine, or a powerful fan. 
The base of the machine must be massive so that the heavy motor does not overturn the structure. By installing pulleys of several diameters on the chuck and electric motor, you can regulate the rotation speed.
Important! Changing the coefficient gear ratio pulleys, you not only reduce the speed. At the same time, the torque increases.
Using this secret, you will be able to use powerful drills with a medium motor.
In addition to working with application tools, there is often a need to perform mechanical work when servicing a vehicle. At the same time, it is not at all necessary to purchase equipment for a car service.
Homemade garage gadgets
Press from a hydraulic jack
Perhaps the most common machine for the garage is homemade press. This is more than necessary. There is a typical regulatory operation for which car services have to pay.
Pressing in (extracting) silent blocks. The procedure is simple, but requires hundreds of kilograms of effort. It is enough to weld a frame from an old profile, and you get a powerful press with a force equal to the lifting capacity of a jack. 
It is enough to acquire pieces of pipes of different diameters (bearing cages are excellent), and a professional remover for silent blocks is ready.
Simple and clear example jack press for garage work
Important! Such equipment can cause injury. The applied force is 2-10 tons, imperceptible by eye. If a crookedly placed part jumps out of the frame under pressure, trouble cannot be avoided.
Another simple helper is a support, or “fixed jack”. All car enthusiasts know that working under a car while it is supported by a jack is dangerous.
Therefore, you should substitute supports after first lifting the body with a jack. In order not to spend money on a purchase, you can make the device yourself. 
You need a high-quality square pipe and stud bolts with a strength of at least 8.0. Otherwise, they will be cut off under the weight of the car.
Ball joint remover
From a piece of pipe and scraps of steel sheet, you can make homemade puller ball joints This item is simply irreplaceable for the garage.
And for straightening drills, screwdrivers and knives, you can make homemade sharpening machines.
A ball joint remover is a much needed item in the garage. Manufacturing details in this video.
We just take a small electric motor (no power is needed for the sharpener), select a suitable bed, and attach the tool rest. The support must provide access to both the radial and end parts of the emery wheel.
You can attach any sharpening jig to the tool rest. For drills and screwdrivers, this is a guide groove. For knives – a plane with a fixed angle of inclination.
Result:
It doesn’t take much time to make any machine or device. Similar processing machines may be needed. You can rent them, or ask familiar craftsmen.
To keep your home comfortable and convenient, sophisticated technology is required. It greatly facilitates household work, but its maintenance requires certain skills and knowledge. Not everyone knows all the possibilities modern instruments and they are not used to their full potential. If you change them a little, you can get convenient homemade tools for the workshop.
If you gradually acquire models from popular brands, they will turn out to be durable and reliable assistants. In addition, devices are needed for positioning and securing workpieces during processing. It will be at the dacha
As the home craftsman's inventory accumulates, it should be sorted into groups:
- plumbing and carpentry tools;
- devices;
- electrical equipment.
Drawers and cabinets allow you to place everything. Keeping equipment clean and tidy makes it possible to create a comfortable working environment and ensure long-term preservation of tools.
Homemade tools for woodworking
Wood processing is most common in the household. Useful homemade tools for the workshop primarily include a workbench. It should be at a comfortable height. Its lid is located at the level of bent palms. If you need to raise it, bars of the required thickness are installed on the dowels below.
Making a modern workbench
The classic workbench consists of a lid with front and rear vices. This design is more suitable for manual work. It is poorly suited to working with power tools due to the fact that workpieces can be difficult to secure. You can buy a modern compact workbench MASTER cut 1000 worth 12 thousand rubles, which folds. You can install hand tools on it: a circular saw, a jigsaw and a router. But then it will have to be redone. Good characteristics has a Festool MFT 3 workbench. However, the price of 30 thousand rubles makes you think. The master will be able to make homemade devices for the home workshop that work just as well.
To make a workbench you will need flat plywood without knots. The thickness must be at least 20 mm. By installing a jigsaw on it from below, you can cut boards and small bars along, across, at an angle, as well as complex curved profiles. The tool performs additional functions of a circular and band saw.
First, the tabletop is made. An arc-shaped groove is cut into it to install a guide for workpieces, which can be mounted at any angle. A guide with a slot is also made under the jigsaw. Its width is selected to match the size of the tool sole.
The sides should be cut out of plywood and glued to the tabletop to give it rigidity. The legs of the workbench are made of timber. Can be made metal carcass, and then attach the tabletop to it with screws. Then the structure will be light and durable. The guides from below are attached to the tabletop with furniture nuts.
The jigsaw is installed from the bottom of the workbench lid - “upside down”. Only the file remains visible from above. For ease of use of the jigsaw, an additional switch is installed. The guide should also be easy to remove so that the tool blade can be easily replaced. For easy access to the underside, the tabletop can be made folding and hinged.
The workbench takes up little space and can be installed even at home. To do this, it is made foldable so that it can be easily disassembled and stored in a closet or pantry.
How to make a workbench for a summer house
To work in the country or in a country house, you need a powerful workbench. The table top is made from thick edged boards up to 2 m long. It will not be superfluous if it is additionally secured with self-tapping screws. The bottom perimeter of the table top is sheathed with timber. The table legs are made with a square section of 120x120 mm. They can be buried in the ground or attached to a reinforced concrete base. The entire structure is treated with an antiseptic and covered with drying oil.
When the workbench is installed, do-it-yourself devices are mounted on it: guides, devices for fastening workpieces and power tools.
How to make a pipe bender with your own hands
In a subsidiary farm it is necessary to have a bending device metal pipes and profiles. The simplest homemade tool for bending pipes with a diameter of up to 20 mm is a steel plate with welded pins. By inserting a workpiece between them, it can be bent to the desired curvature. Such simple devices the pipe is crushed at the bend. To prevent this from happening, you need to fill the pipe tightly with sand. Warming it up will also help. blowtorch, which any master has.
To improve the quality of bending, instead of pins, 2 profiled rollers and a locking element are used. You can also make a special profile from a steel angle and plate and fix it on a workbench that has solid foundation. In the picture, the structure is attached directly to the boards. You can make it portable by mounting it on a steel sheet and securing it to the bottom of the tabletop. Then the pipe bender, which has to be used quite rarely, will not interfere with carpentry work. The portable device, like other homemade workshop tools, can be used in the garage. It is convenient to secure it there, and it may be needed not only for pipes.
Homemade circular saw
Branded machines have high prices, but are quite suitable for a private user homemade instrument for the home workshop. It can be made on the basis of manual, cheaper models.
The workbench for the circular saw must be stable. A frame with a slot for a disk is attached to the tabletop. The best material is a sheet of metal or durable wood that can withstand heavy loads. It has a slight thickness, which makes it possible to use most disc and cut products of sufficient thickness. In addition, the tool itself and the attachment for the machines are attached to the frame. The guide bar is made to slide on a steel or aluminum slide, or fastened with clamps.
Installed from the bottom of the tabletop on the frame. You can also use a grinder or drill, but they are not as effective and do not allow you to use the entire working area of the disk. The fastening can be anything as long as it is reliable.
When working with circular saw It should be remembered that it has high speeds and safety rules must be followed.
Homemade bow saw
Homemade devices for wood processing can be very simple but effective. These include a bow saw. The thin blade makes it possible to quickly cut big log. It is easy to replace it with a new one when the saw becomes dull. You can make your own bow saw from 3 blocks of durable wood. Two handles with cuts at the ends are connected in the middle by a crossbar using a “tenon-socket” connection. The blade is inserted into the slots and secured with two nails. On the other hand, it is tensioned using a rope loop thrown over the handles and twisted with a knob.
How to sharpen a knife
Hand sharpening for knives is more effective because it produces a strong cutting edge. To facilitate the process, a homemade device is widely used. It consists of a bar with a clamp for the bar, a base for fixing the knife and a stand for adjusting the installation angle.
When the rod with a bar attached to it moves back and forth, the blade is sharpened. The abrasive surface is pressed against the blade only when moving from the heel to the tip. By slightly changing the design of the knife sharpening base, you can also straighten the blades of carpentry tools.
Homemade garage gadgets
A garage is not only a place to hide a car, but also a workshop where you can store tools and carry out repair work.
Shelves and racks
Do-it-yourself devices provide order in the garage. To do this, a rack is made, which is usually placed on top. Then it will not interfere with movement inside. A small workbench is installed below, in which tools are also stored. It is most convenient to place everything near the back wall of the garage. Then the side passages will be free.
The inspection pit is lined with bricks or concrete is cast, and then covered with a lid so that it does not interfere with the passage.
Making a puller
Normal work on a car is done using a standard set of tools. Craftsmen make special equipment. A puller is often required to pull bearings together. The most convenient is the three-valve design. A standard device may not be enough. If you make a puller with your own hands, it will last for many years.
Small devices are made from steel sheet 10 mm thick. A pattern is drawn on it and the legs are cut out with a gas cutter. They are processed on an emery machine, adjusting the dimensions. The core is turned out of round timber, the claw holders are welded, threads for the knob are cut and the necessary holes are drilled. The legs are held on by bolts with a diameter of 8-10 mm.
The job of making a puller requires skill with many tools. Helpers may be needed here. A convenient solution is to make removable feet required configurations, which can be changed on a product purchased in a store.
Conclusion
Homemade tools for the workshop allow you to solve many problems in the home and farmstead with minimal effort and expense.
It's nice to see when a person made all the furniture and other household items with his own hands. To simplify the process of cutting metal or sawing elements from wood, they build homemade machines and devices for the home workshop. This solution saves not only time on manufacturing products, but also money on the purchase of finished tools. Let's look at a few practical and interesting options below.
The use of homemade machines and devices for the home workshop is aimed at solving several problems:
- Simplifying the metal processing process. When creating household items, a metal cutter or press is often required.
- Improving wood processing. Even to build a small shed or make a wooden shelf for your home, you need a power saw and other woodworking tools.
Buying a ready-made tool is quite expensive, so the use of homemade machines and devices for the garage is becoming more and more relevant every day. Among the most common options for home tools are:
- carpentry workbench;
- device for quickly sharpening knives;
- device for sharpening metal drills;
- drilling machines;
- press;
- cutting disc machines.
Here are a few photos of do-it-yourself tools and devices from “homemade” people:
Practical DIY tool shelves
Before creating devices and tools for working with your own hands, determine the storage location for all the devices, so that later you don’t have to search throughout the workshop or garage to find out where everything is. It’s not difficult to make a shelf for tools with your own hands; the main thing is to decide on its dimensions and material of manufacture.
The easiest way to make shelves is to assemble them from wood. Do not forget about the need to coat the finished structure with a protective varnish or paint to prevent rotting and swelling of the wood.
You can create a combined version of the rack from a metal support and wooden shelves. Here are detailed instructions for creating such a homemade model:
| Image | Sequencing |
|
Assembling the frame. To do this, prepare two side frames consisting of 4 corners. Connect the elements using self-tapping screws. Then, tighten the 2 frames together using 4 corners. |
|
When the frame is completely assembled, proceed to making the shelves. They can be made from wood or metal, as well as from other dense materials at hand. It is enough to cut the canvases of a suitable size and attach them to a metal base. |
 |
If desired, you can make the rack movable by attaching four small wheels. Or install it firmly in a designated space in the garage. |
You can find other interesting projects and drawings for making tool shelves. Watch the video on the topic:
And also make useful household gadgets with your own hands:
We make a carpentry workbench with our own hands according to the drawings: video instructions and photo examples
Among the common tools for a do-it-yourself carpentry workshop is a workbench. A durable and dimensional table that allows you to securely fasten the workpiece is useful for high-quality cutting of wood and creating various elements from it.
The device package includes:
- Working surface. They use it for hard wood to increase the life of the device. The thickness must be at least 6 cm.
- Supports. Assembled from wooden beams or metal plates. The main task is to ensure the stability of the entire mechanism.
- Vise for securing the product. If the table is long, you can install two vices at once.
- Tool box. A useful recess or pull-out design that provides quick access to needed small parts.
To assemble a carpentry workbench for your workshop yourself, you should choose a drawing and purchase materials for the work.
DIY carpentry workbench drawings
Before purchasing materials to assemble your own workbench, you should think about a detailed drawing. It should include the dimensions of the machine itself; it is advisable to note the dimensions of the materials used and their quantity.
For example, a finished drawing of a folding workbench with your own hands may look like this:
Whatever model you choose to create, take into account several features of the workbench that ensure ease of cutting wood:
- height and length of the master’s arms: the height and width of the tabletop depend on these parameters;
- which hand is working: place the vice on the right or left;
- what blanks will be made: choosing the shape of the table;
- how much space in the room do you allocate for the workbench?
Taking into account all these parameters, it will be easier for you to decide on the drawings of the carpentry workbench and the dimensions of the machine. Here are some interesting examples:
Instructions for assembling a wooden workbench with your own hands
You can buy a wooden workbench in a store or through online catalogs, but it’s cheaper to make it yourself. Let's take as a basis a simple option with typical tabletop dimensions: length - 150-200 cm, width 70-120 cm.
The manufacturing work will include several stages:
| Image | What need to do |
|
Make the top cover from thick boards to create a shield with a width of 70 to 200 cm. You fasten the elements with long nails, and you need to drive them in from the outside and carefully bend them from the inside. The working surface of the workbench is made only of wood or chipboard. |
|
Sheathe the lid along the lower perimeter with a 5 by 5 cm beam. This will make it more convenient to attach the vertical supports. The location of the supports depends on the size of the tabletop. It is better to make them from thick rectangular timber at least 120 by 120 mm. |
|
The carpentry workbench must be installed correctly. Be sure to secure it firmly. If it will be mounted outdoors under a canopy, dig holes for supports. Indoors, use other fastening methods. |
When the structure is assembled, install a vice on it. To fully understand how to assemble a carpentry workbench with your own hands, watch the video:
Making a carpenter's vice for a workbench with your own hands
Professional “homemade craftsmen” assemble not only tables for work, but also handmade notes according to drawings. Any design of such a clamp will include several elements:
- Supports, where each one has a sponge for clamping.
- Moving jaw.
- Metal guides. The sponge moves over them.
- Lead screw for moving elements.
- Collar. Necessary for rotating the screw.
When making a homemade vice with your own hands, you can use various available materials. For example, there is a design option made from a profile pipe. To do this, prepare several pieces of pipe of different sizes, a steel stud with large threads and double nuts.
Instructions for creating a bench vise from a profile pipe:
| Image | What need to do |
|
The largest pipe acts as a body. Supports are soldered to it from below. A 3-4 mm steel flange is put on the back side. A hole for the running nut is drilled in the center, and a rear jaw is welded opposite the front support. |
|
A front steel flange is welded onto the internal moving part. A stud is mounted in it, with lock nuts attached to it. Thrust washers are placed on both sides of the flange. The last element is a movable tube attached to the front jaw. |
And also watch the video “do-it-yourself vice at home”:
DIY metal workbench drawings
A metal carpentry workbench is not much different from a metal workbench. It is based on a rigid metal rather than wooden frame. A vice is attached to it, and the entire workbench is designed to withstand the force of a sledgehammer.
Do-it-yourself metal workbenches can have one, two or three cabinets, and also not have shelves or drawers for small parts. In terms of strength for working in a garage, you can make a regular table made of metal up to 5 mm thick and a reinforced structure where sheets from 10 to 30 mm are applicable.
Here are some useful plans for making a metal workbench for your workshop:
How to make a device for sharpening knives with your own hands: drawings and photo examples
No home is complete without a knife in the kitchen. Correct sharpening It’s quite difficult to do without special tools: you need to maintain the right angle and achieve the ideal sharpness of the blade.
For each knife, a certain sharpening angle must be observed:
- A razor and scalpel require an angle of 10-15⁰.
- Knife for cutting bakery products – 15-20⁰.
- Classic multifunctional knives – 25-30⁰.
- For hunting and hiking, take a device with a blade angle from 25 to 30⁰.
- If you want to cut hard materials, then sharpen at an angle of 30-40⁰.
To ensure the desired angle, it is worth buying or making a sharpening device. For example, you can assemble a sharpener from washing machine motors with your own hands.
To assemble such a machine, you will need a motor from a washing machine with a power of 200 W. If you do not use sharpening every day, then 1000 rpm is enough for high-quality results and a long service life of the device.
To create a sharpener from a washing machine engine, prepare:
- the motor itself;
- metal for the casing with a thickness of 2 to 2.5 mm;
- flange tube;
- sharpening stone;
- nuts;
- trigger mechanism;
- cable for connecting to the electrical network;
- a metal corner or a wooden beam for the frame.
You can watch a step-by-step description of the manufacture of the machine in the video:
There are simple do-it-yourself sharpening machines without motors. For example, you can make a device from bars. To do this, prepare two abrasive stones of the same size and a sharpening stone.
The progress of work on creating such a simple device will be as follows:
- Sand the wood blocks with sandpaper, removing any burrs. Make markings depending on the desired angle.
- Attach a stone to the drawn line to give the blade a sharp edge. To do this, attach it to the block and mark its width. Then, make cuts on the markings, up to 1.5 cm deep.
- Attach abrasive stones to the resulting recesses so that the grooves coincide. Then, install the sharpening stone by screwing it onto the bolts.
There are many ways to make a homemade knife sharpener. Choose the one that suits you and try to create a convenient and useful tool for your home.
How to make a device for sharpening a metal drill with your own hands
They make their own not only a sharpener for blades, but also a machine for sharpening drills for metal. Here are a few drawings useful for work:
To understand how to assemble correctly according to the drawings own machine for sharpening drills, watch the video
The master is not distinguished by greed, which some masters suffer from, who do not want to share their finds with others and, like a dog in the manger, neither to themselves nor to people. And this self-taught inventor came up with a great device with which you will always be at your best and can even improve your standard of living. Why, you can put such a tool into production and sell it to everyone. Maybe this is too strong a word, but it’s worth thinking about automating and mechanizing all routine work at home.
8 tools for craftsmen.
You probably haven't seen many of them. Cool instruments are created by DIYers. These devices will help you work more comfortably in the workshop. The video was filmed on the “Hands from Shoulders” channel.
Folding table for the master
1. Let's start with a folding table, which will be an excellent assistant in a small workshop. Will help you save money too small area. The table has a compartment for all small things. Shelf that can be laid out necessary tool. Thanks to a large number holes using a clamp, you can conveniently and quickly fix the workpieces being processed. Stops are inserted into them. It is convenient to fix the parts in a vertical position. If we insert it into the guide bolts, we get additional stops. Having a set of clamps and such a table, you can comfortably perform a variety of jobs.
Homemade folding stand
2. Very original idea folding stand for hand tools. Everyone is in their place. It doesn't take up much space. The design is based on furniture guides. The stand is held in the upper position. Neodymium magnets prevent instruments from falling out of their stocks. Great idea for DIYers who love to do everything with their own hands.
Apple puller
3.Gardeners will be interested in the fruit puller. Its advantage over analogues is that it is absolutely free and easy to manufacture. Not hard to find at all plastic bottle, rope and cut the stick. 5 minutes and you can go for apples.
Homemade apple press
4. If the harvest is large, then the question arises, where to put it? Great option- Apple juice. For store-bought juicers, apples need to be cut and peeled, which is inconvenient. The grater shown below can handle whole apples. All that remains for Dali is to squeeze out the resulting mass under pressure. As a result, we get natural delicious juice and almost dry cake.
Tool trolley
5. The mobile tool cart is very convenient for the workshop. When, for example, the workbench is littered with parts. Or it doesn't exist at all. After loading everything you need into it, this moment, we get all the tools in one place at hand.
What can you make from an electric planer with your own hands?
6. Another interesting planer design is based on an electric planer. With the help of guides it moves in 2 planes. The movement takes place using an elevator. For precise adjustment, there are rulers on each side of the device.
Grinding device
7. Having a jigsaw, you can get a cool sanding tool. Interestingly, it is not the abrasive that moves, but the workpiece itself.
Cheap homemade grinder
8. The most budget version of the grinder, created by the Samodelkins. Plastic bottles are used as rollers. They are mounted on bearings. The belt on the rollers is adjusted using thumbwheels. The tension is adjusted with a bolt. The structure is driven by a drill. You can slightly improve Samodelkin’s design by replacing plastic bottles with polypropylene tubes.
The self-taught self-made man rocked the network with his video
The self-taught inventor captivated the online community of craftsmen with his video, in which he presented a fundamentally new utility model for improving the efficiency of work for craftsmen and those who like to work in the garage. The best part is that it doesn't require you to buy an idea. And what’s more, you can do all this yourself and even a novice master can handle it. All this is to the benefit of every resident of the cities in which the masters settled, because with such high level mastery, now you won’t want to hammer the walls at home on weekends or rattle some ultra-decibel grinder unknown purpose. With such a device, you can safely create your own separate workshop and live the rich life of a Russian craftsman.
Homemade tool rocks the internet
This video shook up the community of invention lovers on the world wide web. The master thought about this idea for years and finally brought to the public discussion an idea that was ingenious in its simplicity and radically profitable for those who used to chisel walls with a hammer drill, realize their inclinations as a woodpecker and a brilliant builder-grinder, and now can make themselves rich for free, working in silence a workshop in a garage or even in a separate building.
And at the same time, you don’t have to spend money and take money saved for beer out of your stash. All this is free - the master loves to show the whole world the useful things he comes up with.
Uprooting of seedlings and weeds from a square for homemade people
Good afternoon My long absence on the channel was not in vain, during this time I managed to do a lot of household chores. And of course, I stocked up on a bunch of homemade products that I will show you, my dear subscribers and guests! There is no point in posting everything at once, because this also takes a lot of time, but if possible I will try to post at least one per day. Not only am I sitting at the computer, I can’t leave my workshop. Messing around in the garden is another hobby of mine; I spent a lot of time there in the summer. Caring for plants and weeding, although a pleasant activity, however, also requires a lot of effort. And how I would like to make a lot easier. Wanting alone is not enough, so you need to make useful things yourself that will make your work easier and make it a pleasure, rather than hard labor with a farmhand.
Today I’ll show you a device that I successfully used almost all spring and summer and will, God willing, last for more than one season. Do-it-yourself uprooter To make it, I took a square with walls 40 by 40 mm, 220 mm long. I didn’t cut this length on purpose, I had a lot of such scraps left over from others construction work. 
I drew two oblique lines along the walls to the corner of the square. Having cut it out, it turned out to be such a spear. In inner part welded a pipe with a diameter of 25 mm using an angle. From the outside I welded a square right in the middle of the square. Instead of a square, you can weld a square, but it seemed to me that it would be more convenient. 
A metal handle was installed in the pipe so that it would not break under load, because the force falls mainly on the handle. When working with a flat cutter, some types of weeds still germinate after a certain time, especially after rains. And having ripped it out by the roots, I eliminated this possibility and my garden became well-groomed and beautiful. Without damaging the root system, they can also remove seedlings for replanting, which is what I did at the beginning of the season with strawberries and other plants. 
A simple cheap homemade device for picking berries
Gooseberries are a tasty and healthy berry. The plant itself is quite unpretentious and does not require any special care. The berries grow large and are quite convenient to pick. And everything would be fine if it weren’t for the prickly gooseberry branches. Because of these garden “cacti”, previously our hands were constantly in minor scratches. And several times you will think “do you need it - there are so many berries” before you climb deep into the bush for the harvest. But a few years ago my husband made my life easier. He spotted something very simple on the Internet, but useful device for picking berries. What is it used for and how is it useful? 
In fact, such a picker can be used not only for collecting gooseberries. I also use it to collect any other berries/fruits in hard-to-reach places that I can’t easily reach with my hand. For example, to remove plums, cherries or apples from high branches. How to make a device for picking gooseberries? Everything ingenious is simple! Take a plastic bottle and cut a droplet-shaped hole on the side. Depending on what berries/fruits your picker is intended for, this is the diameter of the drop. For gooseberries, 5-7 cm is enough, for apples and plums more, so that you don’t have to aim for a long time and try to hit the fruit. The volume of the bottle will also depend on what you are collecting. For berries would be better suited bottle 0.5 l. 
The droplet's nose should be directed towards the bottom of the bottle. You can also make a cut a couple of centimeters in continuation of the spout so that the branch can be better grasped. That's it, our device is ready! We will pick berries by holding it by the neck.
It really is much easier to do this with him. Not only do your hands remain scratch-free, but the work also goes faster. After all, the harvested crop will be poured into the top of the bottle. Accordingly, there is no need to “climb out” from the bush after each berry, put the harvest in a can or jar and climb again. Plus, we can get berries even from the most inaccessible places. And the most important thing is that such a device is made in 3 minutes, does not cost a penny, and makes life much easier. If it gets lost or gets dirty, no problem – we’ll do another one without any problems! So, gardeners, take action! If the article was useful to you, give it a “thumbs up” and subscribe to the channel for summer residents and gardeners “SADOёZH”.
