In this article we will talk about the manufacturing technology of those tools that are essential to have in the house. They are used not only during the performance of various plumbing or carpentry work, but also for domestic purposes.
An industrial vice is a fairly simple design from an engineering point of view, the manufacturing technology also does not belong to the category of complex ones. But companies sell them at a fairly high price, the only real explanation for this situation is the desire to maximize profits.
We'll show you how to make it at home. functional tool With minimal losses time.
As for materials, the vast majority can be found at scrap metal collection points. Accordingly, their cost approaches zero.
Step 1. Clamp a piece of thick-walled pipe (thickness is notits 4mm, diameter 150mm andlength 100mm) and a grinder with a disk pabout metal, cut it into two ra open halves.
A little lower in this article we will tell you how to make the simplest device for finding the center of round blanks.This is very important point for vices manufactured by us, if it is not fulfilled, additional loads will occur during use.They reduce compressive strength and increase risk of mechanical failure vise .
Step 2. Prepare reinforced curtains. In time squeezing sponges on them significant effort, in stores T There are no solid models. Veils are made in several stages.
- Cut off the metal tube her the length should be equal to the length of the cut large. Tube diameter not less than 10 mm, wall thickness≥ 1mm.
- Divide the tube into 5– 6 parts, each about a centimeter long, the specific quantity depends from the total width of the vise.Cut carefully, all planes must be made only at an angle of 90 °, otherwise the hinges will not work correctly, when opening / closing the sponges wedge.Put curtains on a metal axisrelevant sizes.
- Weld them to the pipe. For it clamp the workpiece in a vise andAlign the halves exactly.
Starting from Aves must be fixed on each side ovate through one, the seams must be very strong, control the quality, eliminate gaps.
Sutures should be applied on both sides , after boiling the first, remove the workpiece, open it and fasten the bushings on the back side.
- Clean off rust and prepare them for painting.
Step 3 Make sponges. To do this, from a piece of sheet steel should cut out elements of the appropriate size.
Steel thickness not mless than 10 mm - spongesthey must have enough I know strength. To reduce the coefficientglide bgrinder cut strips on them s in the form of a grid.
Step 4. Make two hinges for lips vise. What are they needed for? The point is that in industrial with kah lips ki move in a straight line , their planes are always about with t are parallel, and in our case, when tighteningone of them moves c i in an arc, depending on the distance until fully closed, the angle of inclination between them is mgets married. To lips ki always at the moment of clamping relied in pairs a llelno, one of them before l woman to have the opportunity n axis adjustable(swim) . The hinges are made blowing way m.
- Pick up a strip of leaves th steel thickness ≈1 mm, length ≈ 50 mm, width ≈ 20 mm.
- Set in the center Vite metal at th axis Ø 5mm, the same bars must be placed on both and m st about ronam.
- Insert into a vise and squeeze it until it stops. Behind With even such inserts, the sheet will bend.
- Cut the strip in half and cut off two hinges.
Step 5. Attach the hinges to one of the jaws. To do this, first weld on both sides axes along the perimeter of the circle, clean the seams. Zat I need to set the axes to gu bku vise and smooth platforms to weld to it. Remove the metal streaks again, cut off excess pieces bars . Gather together all the details and check their performance.
This completes the preparation of the movable jaws, it is necessary to proceed to the clamping mechanism.
Prices for angle grinders (grinders)
Angle grinders (grinders)
MadeVleneniemechanismclamp
This knot is much more complicated than the one described above. Is being done adaptation andfrom a sheet ≈ 5mm thick, 170mm long, wide 130 mm.
Step 1. On the plate, measure two points for drilling holes for accessories.
They are located along the axis of symmetry, one at a distance of 70 mm from the edge, the second 25 mm. Do not rush, mark with maximum accuracy, each mistake is considered critical th and is not corrected.Will have a base under mechanism completely redo.
Step 2. Carefully drill holes, drill diameter 4mm.
Between them cut a straight groove.Its width should be slightly greater than the thickness of the plate, which later slides in it.
Step 3. Drill two holes in the square, between thewe also need to cut a groove, dThe length corresponds to the width of the inserted plate.Two such plates are required.
Cutting a through groove
Step 4. Gather all the elements together.
Put on flat surface square, on it the base of the clamping device and on top of the second square. In the slots, place the prepared plate with a hole at the top end. Weldinggrab the parts, then assemble them in a vice in reverse order and firmly weld the protruding plate with a hole to the lower square.
Turn the structure over again and apply welds on this side. Do you have a debtwives get a mobile unit:two squares slide along the base plate of the mechanism, a part with a hole is welded to them.
Thoroughly clean the seams with a circular grinder, if necessary, strengthen weak points.
Step 5. Prepare another part, the so-called thrust plate. The length is equal to the width of the base of the clamping mechanism, the width is about 3 cm.In the center, you need to make a hole for the clamping bolt.Now you should start assembling the elements.
Step 6. Prepare two ears with holes, each 25mm long, hole diameter 8mm.
Install them on the movable plate of the mechanism on both sides and connect with a bolt.Do not overtighten the nut elements must be able swing around the axis.
Step 7. Install movable jaws close to the parts and weld the knots together.
Watch out h So that all axes are parallel or perpendicular, depending on the purpose and arrangement of the elements. You should already understand the principle of the vise, this will help you choose correct positions each element.Weld the parts firmly.After cleaning the seams, assemble the vise on the bolt, again do not tighten it too much.
Step 8. Now start making fixed vise assembly. It will need a few details:
- two at the cabinet 40 × 20mm;
- two at shk a 25 × 20mm;
Metal thickness 2 mm, hole diameter is selecteddepending on bolt size in our case, 6 mm.
WITH collect the elements: first put on the bolt nb those short eye, then two long ones, and then one more short one.
Step 9. Install long ears at the edge of the clamping mechanism, place exactly along the axis of symmetry.Weld them firmly.
Step 10. Mark the place where the halves of the vise are fixed to the short lugs. Fix the elements, disassemble the vise, strengthen all welds.
Step 11. Make a stubborn platform for the screw. For this purpose, it is recommended to use a nut of the appropriate thickness. She is welded to a moving square with reverse side . Weld seam, like Always , superimposed around the entire perimeter of the parts. check slave resilience and smooth running, P When tightening / loosening the screw, the movement of the parts should be easy and without various jams. If there are problems, then you need to find and fix them. reason. It may be burrs, metal streaks, slight nervousness.
The vise is completely ready. Paint their surfaces with a special one and after it dries, you can use a hand-made tool.
Prices for popular brands of portable welding machines
Portable welding machine
Video - Do-it-yourself vice from a channel
Center qualifier
The need to find ntr round parts arises almost always when for the manufacture of various crafts round blanks are used. To make fixture used school wooden triangle and metal protractor.
But this is optional, you can use other blanks, the main thing is that one has a right angle, and the second has a flat strip.
Step 1. With a pencil, continue the length of the legs along the hypotenuse.
Saw off excess pieces with a hacksaw, clean the cuts with a file or sandpaper.
Important.Pay attention that the inner lines of the legs are perfectly even, otherwise the center is determined incorrectly.
The part may rest against a ledge or fall into a recess,in this positionit is impossible to accurately draw diameters, and the center of the circle automatically shifts to one or another st O ronu. When making some fixtures errors can be critical. It is strongly recommended that after sawing off, check the specified requirements with a new triangle.
Step 2. Cut off a semicircular scale from the protractor; for further work, you only need a flat strip.
The protractor is made from aluminum alloy 0.3 mm thick, it can be cut without problems with ordinary household scissors.Remove the burrs with a file, they are very sharp and can injure your hands while using the tool.
Step 3. install aluminum stripe strictly along the bisector of the triangle.
Bisector - a line dividing the angle exactly in half.We have an angle of 90 °, which means that the bisector should be located at an angle of 45 °. Finding it is easy.Insert the second isosceles right triangle into the workpiece so that its hypotenuse lies on the leg. In equilateral right triangles, the angle between the legs and the hypotenuse is 45°, which is exactly what we needed to find.
Step 4. Attach the prepared aluminum strip tightly to the leg of the inserted triangle, align it exactly. It is necessary to achieve such a position that one of its faces passes along the angle of the cut off. With a thin pencil draw a line.
Step 5. Mark drill points holes . They are required at least three, two do not guarantee reliable fixation strength, which causes the element to shift. As a result - errors in the definitions of the center.
Holes can be drilled with a drill or a screwdriver with a drill with a diameter of up to 1mm. No electric tools- no problem. Aluminum alloy is so soft that holes can be pierced with the tip of an ordinary nail. As always , after drilling with a file it is necessary take off sharp burrs. Same holes. must be done in wooden parts fixtures .
Step 6. Use small screws to connect the elements into a single construction . Small screws are required (great for a desktop mount), too large will split the thin rail of the triangle.
Practical advice.During connection, constantly control the location of the strip, put the second triangle and focus on planes.
First, it is recommended to tighten one screw a little, check the position, then wto Roy. Again a littlecorrect. Everything is normal - you can tighten them all the way and install a third. Use your fingers to press the aluminum strip very firmly against wooden slats, when twisting, it can change its position. After fixing, it is necessary to check the bisector again.
Fixture assembly
Step7 . Cut off the part protruding beyond the perimeter of the triangle with scissorsstripes, burrs grind off.
Step 8. Take away the sharp the ends of the screws, work carefully with a file, do not loosen the connections.
Step 9 For improvement appearance paint determinant center. Choose your paint carefully.The fact is that part of the fixture is wooden, and part is metal, you need to use only wear-resistant universal paint. Before applying it, it is imperative to degrease the aluminum part. Wipe its surfaces with refined gasoline, acetone, or other chemical solvent. The paint can be applied only after the liquid has completely dried.
On this manufacturing process finished, you can use adaptation by appointment. How exactly is this done?
- Paste between the legs of the device a round billet. Press it, it should touch everyone at one point.
- Turn the fixture back and along the bisector line draw a line.
- Turn the part a little and again do the above steps. The center of the circle is located at the point where the two lines intersect.
We explained the principle device manufacturing. If you intend to work with large diameter workpieces, t about the length of the cathe t ov should increase.It is not necessary to use factory triangles, they can be made any size with my own hands.
On our site you will find a lot of interesting things. For example, detailed instructions for making, as well as answers to topical issues: what types of boxes are divided into and what are their advantages? Tips for making a screen for a heating radiator from experienced craftsmen.
It's nice to see when a person made all and other household items with his own hands. To simplify the process of cutting metal or cutting wood elements, they construct homemade machines and accessories for the home workshop. This solution saves not only time for the manufacture of products, but also money for the purchase of finished products. Several practical and interesting options consider below.
DIY pipe bending machine
Read in the article
How to use homemade machines and fixtures for the home workshop
The use of home-made machines and devices for the home workshop is aimed at solving several problems:
- Simplification of the metal processing process. In the course of creating household items, a metal carver or a press is often required.
- Improvement in wood processing. Even to build small barn or make a wooden one, others are also needed.
Buy finished tool quite expensive, so the use of home-made machines and accessories for the garage is becoming more and more relevant every day. Among the most common options home instrument allocate:
- carpenter's workbench;
- device for quick sharpening of knives;
- device for sharpening metal drills;
- drilling machines;
- press;
- cutting disc machines.
Here are a few photos of do-it-yourself tools and fixtures from "homemade" ones:
1 of 4
Practical DIY tool shelves
Before creating devices, and with your own hands, determine the storage location for all devices, so that later you do not have to look throughout the workshop or where everything lies. It is not difficult to make a shelf for tools with your own hands, the main thing is to decide on its dimensions and material of manufacture.
The easiest way to make shelves is to assemble them from wood. Do not forget about the need to cover the finished structure with a protective varnish or to prevent rotting and swelling of the wood.
You can create a combined version of a metal support and wooden shelves. Here detailed instructions to create such a homemade model:
| Image | Sequencing |
 | Assemble the frame. To do this, prepare two side frames, consisting of 4 corners. Connect elements with . Then, tighten 2 frames together using 4 corners. |
 | When the frame is fully assembled, proceed to the manufacture of shelves. They can be made from wood or metal, as well as from other improvised dense materials. It is enough to cut the canvases of a suitable size and fix them on a metal base. |
 | If desired, you can make the rack movable by attaching four small wheels. Or firmly install it in the allotted place in the garage. |
You can find others interesting projects and drawings for the manufacture of shelves for tools. Watch a video on the topic:
And also to make useful devices for household:
1 of 4
We make a carpentry workbench with our own hands according to the drawings: video instructions and photo examples
Among the common do-it-yourself devices, a workbench is distinguished. Durable and dimensional, allowing you to securely fix the workpiece, it is useful for high-quality cutting of wood and creating various elements from it.
The device package includes:
- Working surface. For it, a solid one is used to increase the life of the device. The thickness must be at least 6 cm.
- Supports. Collected from wooden beams or metal plates. The main task is to ensure the stability of the entire mechanism.
- Vice for fixing the product. If the table is long, you can install two vices at once.
- Tool box. Useful recess or retractable design, providing quick access to the small parts you need.
To independently assemble a carpentry workbench for your workshop, you should choose a drawing, purchase material for work.
Do-it-yourself carpentry workbench drawings
Before buying materials to build your own workbench, you should think about a detailed drawing. It should include the dimensions of the machine itself, it is advisable to note the dimensions of the materials used and their quantity.
For example, finished drawing a folding workbench with your own hands may look like this:
Whatever model you choose to create, consider several features of the desktop that provide the convenience of cutting wood:
- the height and length of the hands of the master: the height and width of the countertop depend on these parameters;
- which hand is working: place the vise on the right or left;
- what blanks will be made: selection of the table shape;
- how much space in the room you allocate for a workbench.
Given all these parameters, it will be easier for you to decide on the drawings of the carpentry workbench and the dimensions of the machine. Here are a few interesting examples:
Instructions for assembling a wooden workbench with your own hands
You can buy a wooden workbench in a store or through online catalogs, but it's cheaper to make it yourself. Let's take as a basis a simple option with standard sizes countertops: length - 150-200 cm, width 70-120 cm.
Manufacturing work will include several stages:
| Image | What need to do |
 | Make the top cover from thick ones to make a shield with a width of 70 to 200 cm. Fasten the elements onto long nails, and you need to drive them in from the outside, and carefully bend them from the inside. The working surface of the workbench is made only of wood or. |
 | Sheathe the lid along the lower perimeter with a 5 by 5 cm timber. This will make it more convenient to mount the vertical supports. The location of the supports depends on the size of the countertop. It is better to make them from a thick rectangular bar at least 120 by 120 mm. |
 | The carpenter's workbench must be installed correctly. Be sure to fasten it firmly. If it will be mounted on the street under a canopy, then dig holes for the supports. Indoors, use other methods of fastening. |
When the structure is assembled, place a vise on it. To fully understand how to assemble a carpentry workbench with your own hands, watch the video:
Making a carpenter's vise for a workbench with your own hands
Professional "homemade" assemble not only tables for work, but also a vise with their own hands according to the drawings. Any design of such a clamp will include several elements:
- Supports where each has a sponge for clamping.
- Moving clamping jaw.
- Metal guides. A sponge moves over them.
- Lead screw, for moving elements.
- collar. Required to rotate the screw.
In the manufacture of homemade vise with your own hands, you can use various improvised materials. For example, there is a design option from profile pipe. To do this, prepare several pieces of pipe different sizes, steel stud with coarse thread and double nuts.
Instructions for creating a verstal vice from a profile pipe:
| Image | What need to do |
 | The largest pipe acts as a body. Supports are soldered to it from below. A 3-4 mm steel flange is put on the back side. A hole is drilled in the center for running nut, and opposite the front support, the back sponge. |
 | On the inner moving part, the front steel flange. A stud is mounted in it, with lock nuts fixed to it. Thrust washers are put on both sides of the flange. The last element is a movable tube attached to the front sponge. |
And also watch the video "do-it-yourself vise at home":
Do-it-yourself metal workbench drawings
A metal workbench does not differ much from a carpenter's workbench. Based on hard metal, not wooden frame. A vise is attached to it, and the entire workbench is designed to withstand the force of a blow from a sledgehammer.
Do-it-yourself metal workbenches can have one, two or three cabinets, and also not have shelves and drawers for small parts. For strength to work in the garage can be done regular table from metal up to 5 mm thick and reinforced structure where sheets from 10 to 30 mm are applicable.
Here are some useful drawings for making metal workbench for your workshop:
How to make a do-it-yourself knife sharpener: drawings and photo examples
No home is complete without a knife in the kitchen. It is rather difficult to make the correct one without special devices: it is necessary to observe desired angle and achieve perfect sharpness blades.
For each knife, a certain sharpening angle must be observed:
- Razor and scalpel require an angle of 10-15⁰.
- Knife for cutting bakery products - 15-20⁰.
- Classic multifunctional knives - 25-30⁰.
- For hunting and camping, they take a device with a blade angle from 25 to 30⁰.
- If you want to cut hard materials, then sharpen at an angle of 30-40⁰.
To ensure the desired angle, it is worth buying or making a sharpening device. For example, you can assemble a sharpener with your own hands.
A comment
Specialist in the selection of tools "VseInstrumenty.ru"
Ask a Question"If you use sharpening not every day, then 1000 rpm is enough for a quality result and a long service life of the device.
"To assemble such a machine, a motor from a “washer” with a power of 200 watts is useful. Completely to create a grindstone from an engine from the Workflow for creating such a simple device will be as follows:
- Sand the wood blocks sandpaper by removing the burrs. Make a markup depending on the desired angle.
- Attach a stone to the drawn line to sharpen the blade. To do this, attach it to the bar and mark its width. Then, on the markings, make cuts, up to 1.5 cm deep.
- In the resulting recesses, fix the abrasive bars so that the grooves match. Then, install the sharpening stone by screwing it onto the bolts.
There are many ways to make a homemade knife sharpener. Choose the right one and try to create a convenient and useful tool for the home.
How to make a do-it-yourself tool for sharpening a drill for metal
They independently make not only a sharpener for blades, but also a machine for sharpening drills for metal. Here are some drawings to help you get started:
Ready home machine The simplest and most common version of such equipment for the garage is a converted drill. For work you will need: - bed for the base;
- rotation mechanism;
- vertical stand.
For a rack, boards are usually used. The mass of the drill is small, so there is no need to use metal. In this case, the frame must be made massive in order to reduce vibration during the operation of the device.
To properly connect the frame and vertical rack, and also assemble all the equipment into one whole machine, pay attention to the video instruction:
Do-it-yourself drawings with dimensions for a drilling machine
To properly make any machine or practical device for private use, you first need to make a drawing with dimensions. Only then proceed to the preparation of materials and assembly of the device.
Here are some examples of do-it-yourself drilling machine drawings from a drill:
And you can also make homemade vise for drilling machine. Below is a video instruction for assembling such a device:
Article
Living in your own country house you often notice that something needs to be repaired, something needs to be modernized to increase the comfort of living in it. This means that you need to do something with your own hands. And you have to solve different problems, then become a carpenter, then a locksmith, then a plumber, then a stove-maker or a painter. The volume of work is such that it is impossible to cope with them with bare hands. There is no doubt that the hands and head are the main tools, but they need convenient, reliable and silent helpers. Therefore, each master should have an arsenal of necessary tools to solve these problems. It should include the necessary set of tools without which it is impossible to do serious work and be replenished only with those that are needed to ensure more high performance work or increase its comfort. Let's define this necessary minimum For different types works.
In my opinion, the minimum set of carpentry tools includes the following tools:
1-metal planer; 2-small planer; 3 screwdrivers; 4 clamps; 5-hacksaw for wood; 6-hacksaw combined; 7-hammer; 8-hand drill; 9-chisel; 10-roulette; 11-miter box with a saw; 12 glass cutter; 13-stapler; 14-building knife; 15-F clamp; 16-wooden planer; 17-axe; 18-sledgehammer; 19-nail puller; 20-level.
The minimum set of tools for metalwork includes:
1-vice; 2-folding workbench; 3-locksmith assembly tool; 4-hacksaw for metal; 5-pincers; 6 scissors for metal; 7-pliers; 8-pliers; 9-nippers; 10 files; 11-needle files.
The minimum set of tools for plumbing work includes:
1-lever key; 2-universal permutation key; 3-key adjustable; 4-knife for plastic pipes.
The set of oven tools required for the job includes:
1-hammer pickaxe; 2-trowels; 3-trowel; 4-level; 5 plumb; 6 laser level; 7-building cord; 8 mallet; 9-rule.
Small comment - until there were laser devices, all stove-makers used a level and a plumb line when working. Laser level allows you to quickly and clearly determine the vertical and horizontal, which is very convenient when laying the stove, but it tires the eyes. Therefore, I used it only for the initial installation and periodic control.
The painting tools required for the job include:
painting tool1-handbrake brushes; 2-maklovitsa; 3-panel brushes; 4-flute brushes; 5-radiator brushes; 6-paint spatula; 7-plastic spatula; 8-spatula scraper; 9-rubber spatula; 10-tooth trowel; 11-angle spatula; 12-mini roller; 13-universal roller; 14-window roller.
A comment — manual paint brushes (handbrakes) - These are rather small brushes, usually with a wooden handle. The brush with glue fastening of a beam is intended generally for works with oil paints. brush with metal mount beam, you can work with almost any painting composition. Maklovitsy Designed for large scale painting jobs. Panel brushes designed for coloring only. hard-to-reach places, drawing fine lines, or stretching narrow stripes. Flanged paint brushes intended mainly for finishing, that is, to smooth out traces of the handbrake. This operation is called "flaming", hence the name of the brush. It can also be used when painting the surface, if a high-quality, glossy surface is required. Radiator brushes Designed for hard to reach places such as inner sides heating radiators. At notched trowel the main thing is the size of the teeth, which is determined based on the operation in which it is applied. The largest teeth are for working with drywall or porcelain stoneware, the smaller ones are for tiles, very small ones are for working with synthetic adhesives that are used when laying carpet, linoleum, etc.
Speaking of carpet. There are troubles on the carpet either something dirty is poured or something sticky is spilled. This is where carpet cleaning can help. Sometimes there is simply no other way to deal with pollution without dismantling the coating.
The rest of the tools do not require comments in my opinion.
Finally, the necessary power tools:
power tools1-electric jigsaw;; 2-electric planer; 3-impact drill; 4-perforator; 5-screwdriver; 6-circular; 7 chain saw; 8 Bulgarian.
The above list of tools is not a dogma. Everyone forms their own arsenal of assistants on their own, based on their needs and capabilities.
- Handmade gift for Valentine's Day. (0)
Book for a loved one 55 reasons. Gift idea for February 14th. A gift for February 14 can make anyone […]
For work around the house or in the garage, professional tools are needed. But in some cases it is more expedient to make the equipment with your own hands. As a basis, you can take factory models adapted to perform a specific type of work in the workshop.
Machine tools for metal processing
The most demanded are machines and equipment for processing metal products. They are used not only for the manufacture and repair, but also during the maintenance of other tools.
Apart from hand tools to complete the repair base of a private garage or workshop, you will need mini-machines various types made by hand. This is not about professional factory equipment, but about its analogue of lower productivity. However, despite this, it must have an optimal set of functions for the implementation of all types of work.
Sharpening equipment
Grinding equipment is considered a machine of first necessity. It is designed to handle metal surfaces- sharpening, grinding, polishing.
To make it yourself, you will need a minimum of tools and components. The design consists of a power unit (electric motor) and grindstones. The best option for the machine is the presence of a double-sided shaft. This will allow you to install two grinding wheels for different types of processing.
Components for making mini garage equipment:
- electric motor with power from 0.8 to 1.5 kW. The optimal speed is 800 rpm;
- base. It can be a factory bed or made independently. It is important that it ensures the stability of the structure;
- emery attachment block. Grinding wheels can be mounted on the motor shaft or in a separate unit.
It is important to choose the right types of emery and other devices. For sharpening tools made of special grades of steel, corundum or diamond wheels are most often used.
For stability, a home-made design must have mounting elements with which the grinding machine will be attached to the desktop.
Milling (drilling) machine for metal
Another type of work is drilling holes on the surface of metal products. To perform, you will need a milling machine. As a basis, you can take a drawing of a factory model, which will later be adapted for making with your own hands in the workshop.
Since the device will perform a number of specific functions, it is recommended to consider the layout of the tool. Most often, an electric drill is chosen as a power unit. It is installed on a removable mounting element and, if necessary, can be quickly dismantled to perform other work.
- as a lifting mechanism, you can use the steering rack. According to its dimensions, the remaining components of the equipment are calculated;
- to increase functionality. After fixing the part on it, it will be able to move relative to the cutting part;
- in addition, you can install the mechanism of angular milling drilling.
If you need to drill thick workpieces using the above machine, it is best to use a powerful electric motor instead of a drill. Then a torque transmission unit must be installed.
Some manufacturers offer a router table with a support stand specifically designed for mounting a drill.
Homemade woodworking machines
Woodworking requires three types of machines: cutting, grinding and turning. With them, you can carry out all types of work at home. However, one should take into account design differences specific to each type of equipment.
Before choosing the optimal model, you should decide on the type of work performed. The parameters of the future design are influenced by the size of the workpiece, the required degree of its processing, and the type of wood. The best option tool will be manufactured universal tool with your own hands based on the analysis performed and the dimensions of the place in the workshop.
Cutting machines for wood
The most simple model mini cutting equipment for woodworking - electric or chainsaw. With its help, you can make cuts of various accuracy and configuration. However, due to the relatively high physical activity, the working time will be limited. Therefore, for processing large volumes of wood, it is recommended to make sawmills with your own hands.
Such machines can be of several types:
- disk. The simplest version of the device, consisting of a support table, a cutting disc and a power plant. Can be used for cutting sheet materials, bars and boards;
- . Designed for processing trunks. It is used for the formation of boards and beams. Differ in rather small complexity of production;
- band sawmill. It has the same functions as chainsaw designs. The difference lies in the speed of processing the log.
For curly cuts, you can use electric jigsaws. However, making this tool with your own hands will be problematic.
In the manufacture homemade sawmill should be considered maximum size logs - the diameter of the trunk and its length. Based on this, it is calculated optimal size and device characteristics.
Sanding equipment for woodworking
For grinding wood, you can use do-it-yourself machines similar to metal processing devices. The difference will be in the abrasive material as well as the processing area.
The simplest fixture model consists of a work table, a motor and a vertical grinding shaft. The latter may have a blade or mounting elements for installing an abrasive belt. With the help of this equipment, it is possible to process the end edges of wooden blanks, to perform their grinding.
The video shows the best set of tools for doing housework with your own hands:
Examples of machine drawings
DIY manufacturing various crafts, furniture, self repair cars are popular not only because of the innate ability of our people to create. This is also a good savings for the family budget.
However, such a hobby requires special equipment. Every home has basic hand tools, including electric ones. Drill, screwdriver, grinder, manual Circular Saw, jigsaw.
These tools make the job easier home master, but with their help it is impossible to perform the work professionally. The home workshop should be equipped with compact machines.
Overview of homemade machines for the home workshop - video
Such equipment is offered in abundance by specialized stores.
Equipping workplace with such an arsenal, you can make anything. But the high cost of the tool negates the savings in the production of crafts.
There is only one thing left - to make machines with your own hands. Homemade equipment can work just as good as the factory one. In addition, constructive know-how can be added to expand the possibilities.
Homemade machines for a home wood workshop
Wood lathe
It can be made from existing tools. Enough strong table, or just a massive board mounted on legs. This will be the bed.
A clamping spindle for wooden blanks is optional. As well as a separate drive motor. There is a simple complete solution- electric drill.
If there is a speed controller - generally great. It is fixed in the cartridge drill bit on wood. It needs to be finalized: sharpen the working edge in the form of a trident.
The next mandatory element is the tailstock. In metal lathes, it is necessary to support long blanks. When processing wood on a machine without a clamping spindle, the tailstock is a locking element. She presses the blank to the trident and supports it on the axis of rotation.
Typical design of the tailstock in the illustration. 
The cutter in such a machine is not fixed in the caliper. Wooden blanks are processed with a hand chisel, which rests on a handpiece.
Homemade wood milling machines
The complexity of the tool depends on the type of work performed. For elementary end processing, it is enough just to install a hand router under a flat tabletop. The power tool is mounted upside down, the working nozzle protrudes above the surface. Such homemade machines are widespread among home craftsmen.
Important! Industrial tools are designed and built with safety in mind. A rotary router can cause serious injury, so the attachment must be secure and the processing area must be protected from the operator's limbs.
If the bracket for manual router equip with a height adjustment device, you will get semi-professional equipment.
There are also more complex designs. If you install a reliable suspension for a manual router, you will be able to perform complex figured processing, including using templates. 
Homemade drilling machines. Eat convenient devices for drills that turn hand tools into stationary equipment. But such racks again cost money. 
Such devices are easy to do with your own hands. One option is to use furniture drawer guides. In a drilling machine, the main task is to ensure the rectilinear movement of the chuck along the axis of rotation.
The simplest machine is a guide device, and movement is carried out without additional levers.
With one hand, the machine is pressed against the workpiece, and with the second, the drill is lowered along the guides. For working with wood, such homemade machines are suitable. For processing thick metal, you will need more heavy equipment.
How to make a homemade drilling machine, see this video
Our "kulibins" have learned to use the steering racks from the "Zhiguli" as a mechanism for a drilling machine. You can use a hand drill if you attach the clamp clamp to the steering arm attachment points.
If you need a really powerful machine, you will have to use a separate electric motor. The same steering rack is taken as the basis, only instead of a clamp and a hand drill, a bed with a cartridge, a belt drive, and powerful engine. The power plant can be taken from the old washing machine, or a powerful fan. 
The base of the machine must be massive so that the heavy motor does not overturn the structure. By installing pulleys of several diameters on the chuck and electric motor, you can adjust the rotation speed.
Important! Changing the coefficient gear ratio pulleys, you are not only slowing down. At the same time, the torque is increased.
Using this secret, you can use powerful drills with a medium motor.
In addition to working with application tools, it is often necessary to perform mechanical work when servicing a car. At the same time, it is not at all necessary to purchase equipment for a car service.
Homemade garage fixtures
Press from a hydraulic jack
Perhaps the most common garage machine is homemade press. More than necessary thing. There is a typical routine operation for which car services have to be paid.
Pressing (extraction) silent blocks. The procedure is simple, but requires an effort of hundreds of kilograms. It is enough to weld a frame from the old profile, and you get a powerful press with a force equal to the load capacity of the jack. 
It is enough to get pieces of pipes of different diameters (bearing clips are great), and a professional puller for silent blocks is ready.
simple and good example jack press for garage work
Important! Such equipment can cause injury. The applied force is 2-10 tons, imperceptibly "by eye". If a crooked part pops out of the frame under pressure, trouble cannot be avoided.
Another simple helper is a support, or “fixed jack”. All motorists know that it is dangerous to work under a car when it is supported by a jack.
Therefore, it is necessary to substitute the supports, having previously raised the body with a jack. In order not to spend money on the purchase, the device can be made independently. 
A high-quality square-section pipe is required, and stud bolts with a strength of at least 8.0. Otherwise, they will be cut off under the weight of the car.
Ball joint puller
From a piece of pipe and scraps of steel sheet, you can make homemade puller ball bearings. The thing for the garage is simply irreplaceable.
And for editing drills, screwdrivers and knives, you can make homemade grinding machines.
A ball joint puller is a much-needed thing in the garage. Production details in this video.
We just take a small electric motor (no power is needed for the sharpener), select a suitable frame, and fasten the handguard. The support must provide access to both the radial and the end of the emery wheel.
Any jig for sharpening can be attached to the handpiece. For drills and screwdrivers, this is a guide chute. For knives - a plane with a fixed angle of inclination.
Outcome:
For the manufacture of any machine or fixture, it will not take much time. Similar processing machines may be needed. They can be rented, or asked from familiar masters.
To maintain a home comfortable and convenient, sophisticated equipment is required. It greatly facilitates household work, but certain skills and knowledge are required to maintain it. Not everyone knows all the possibilities modern instruments and are not fully utilized. If you change them a little, you can get convenient home-made fixtures for the workshop.
If you gradually acquire models of popular brands, they will turn out to be durable and reliable assistants. In addition, devices are needed to position and secure the workpieces during their processing. At the cottage it will be
As the inventory of the home master accumulates, it should be sorted into groups:
- metalwork and carpentry tools;
- appliances;
- electrical equipment.
All accommodation allow fixtures drawers and cabinets. Keeping inventory clean and tidy makes it possible to create a comfortable working environment and ensure the long-term preservation of tools.
Homemade tools for woodworking
Wood processing is most common in the household. Useful homemade tools for the workshop primarily include a workbench. It should be comfortable in height. Its cover is located at the level of bent palms. If you need to raise it, bars of the desired thickness are installed on the dowels from below.
Making a modern workbench
The classic workbench consists of a lid with a front and back vise. This design is more suitable for manual work. It is poorly adapted to work with power tools due to the fact that workpieces can be difficult to fix. You can buy a modern compact workbench MASTER cut 1000 worth 12 thousand rubles, which is folded. You can install hand tools on it: a circular saw, a jigsaw and a router. But then it will have to be redone. good performance has a Festool MFT 3 workbench. However, the price of 30 thousand rubles makes you wonder. The master will be able to make home-made fixtures for the home workshop that work just as well.
To make a workbench, you will need flat plywood without knots. The thickness must be at least 20 mm. By installing an electric jigsaw on it from below, it will be possible to cut boards and small bars along, across, at an angle, as well as complex curved profiles. The tool performs additional functions of circular and band saws.
First, the tabletop is made. An arcuate groove is cut in it to install a guide for blanks, which can be mounted at any angle. A guide with a slot is also made under the jigsaw. Its width is selected according to the size of the sole of the tool.
The sides should be cut out of plywood and glued to the countertop to give it rigidity. The legs of the workbench are made from a bar. Can be crafted metal carcass, and then attach the table top to it with screws. Then the design will be light and durable. The guides from below are attached to the countertop with furniture nuts.
The jigsaw is installed from the bottom of the workbench cover - “upside down”. From above, only the file remains visible. For the convenience of using a jigsaw, an additional switch is installed. The guide should also be easy to remove so that you can easily change the saw blade of the tool. For easy access to the underside, the tabletop can be made folding, on hinges.
The workbench takes up little space and can be installed even at home. To do this, it is made foldable so that it can be easily disassembled and put away in a closet or pantry.
How to make a workbench for a summer residence
To work in the country or in a country house, you need a powerful workbench. The tabletop is knocked together from a thick edged board up to 2 m long. It will not be superfluous if it is additionally fixed with self-tapping screws. From below, along the perimeter, the tabletop is sheathed with timber. Table legs are made of square section 120x120 mm. They can be buried in the ground or attached to a reinforced concrete base. The whole structure is treated with an antiseptic and covered with drying oil.
When the workbench is installed, do-it-yourself devices are mounted on it: guides, devices for fastening workpieces and power tools.
How to make a pipe bender with your own hands
In the subsidiary farm it is necessary to have a device for bending metal pipes and profiles. The simplest home-made tool for bending pipes up to 20 mm in diameter is a steel plate with welded pins. By inserting a workpiece between them, it can be bent to the desired curvature. Such simple devices the pipe is crushed at the bend. To avoid this, it is necessary to tightly fill the pipe with sand. Warming it up will help too. blowtorch that every master has.
To improve the quality of bending, instead of pins, 2 profiled rollers and a locking element are used. You can also make a special profile from a steel angle and a plate and fix it on a workbench that has solid foundation. In the picture, the structure is attached directly to the boards. You can make it portable by mounting it on a steel sheet and fixing it to the bottom of the tabletop. Then the pipe bender, which is rarely used, will not interfere with carpentry work. The portable device, like other homemade workshop tools, can be used in the garage. It is convenient to fix it there, and it may be needed not only for pipes.
Homemade circular saw
Branded machines have high prices, and it is quite suitable for a private user homemade tool for home workshop. It can be made on the basis of manual, cheaper models.
The workbench for the circular must be stable. A frame with a slot for the disk is attached to the tabletop. The best material is a sheet of metal or durable wood that can withstand heavy loads. It has a slight thickness, which makes it possible to use most blade and cut products of sufficient thickness. In addition, the tool itself and the fixture for machine tools are attached to the frame. The guide bar is made sliding on a steel or aluminum sled, or fastened with clamps.
Mounted on the bottom of the worktop on the bed. You can also use a grinder or drill, but they are not as effective and do not allow you to use the entire working area of \u200b\u200bthe disk. The mount can be anything, as long as it is reliable.
When working with circular saw it should be remembered that it has high speed and it is necessary to follow safety rules.
Homemade bow saw
Homemade fixtures for wood processing can be very simple, but effective. These include the bow saw. Thin blade for fast sawing big log. It is easy to replace with a new one when the saw becomes dull. A bow saw can be made independently from 3 blocks of durable wood. Two handles with cuts at the ends are connected in the middle by a crossbar using a “thorn-nest” connection. The canvas is inserted into the slots and fixed with two nails. On the other hand, it is stretched with a rope loop thrown over the handles and twisted with a collar.
How to sharpen a knife
Manual sharpening for knives is more effective because a strong cutting edge is obtained. To facilitate the process, a home-made device is widespread. It consists of a bar with a clamp for a bar, a base for fixing a knife and a rack for adjusting the installation angle.
With the reciprocating movement of the bar with the bar fixed on it, the blade is sharpened. The abrasive surface is pressed against the blade only when moving from the heel to the tip. By slightly changing the design of the knife sharpening base, you can also straighten the blades of carpentry tools.
Homemade garage fixtures
The garage is not only a place where to hide the car, but also a workshop where you can store tools and carry out repairs.
Shelves and racks
Do-it-yourself devices provide order in the garage. For this, a rack is made, which is usually placed on top. Then it will not interfere with movement inside. A small workbench is installed below for work, in which tools are also stored. It is most convenient to have everything near the back wall of the garage. Then the side passages will be free.
The inspection pit is laid out with bricks or cast concrete, and then covered with a lid so that it does not interfere with the passage.
Making a puller
Normal work with the car is carried out using a standard set of tools. Craftsmen make special equipment. A puller is often required to tighten bearings. The most convenient is the three-valve design. A standard device may not be enough. If you make a puller with your own hands, it will last for many years.
Small devices are made of steel sheet 10 mm thick. A pattern is made on it and paws are cut out with a gas cutter. They are processed on an emery machine, adjusting the dimensions. The core is machined from round timber, the foot holders are welded, the thread for the collar is cut and the necessary holes are drilled. The paws are held on bolts with a diameter of 8-10 mm.
The work of making a puller requires skills in working with many tools. Helpers may be needed here. A convenient solution is the manufacture of removable paws desired configurations, which can be changed on a store-bought product.
Conclusion
Homemade accessories for the workshop allow you to solve many problems in the household and subsidiary farms with minimal effort and cost.
It's nice to see when a person made all the furniture and other household items with his own hands. To simplify the process of cutting metal or cutting wood elements, they build home-made machines and fixtures for the home workshop. This solution saves not only time for the manufacture of products, but also money for the purchase of a finished tool. A few practical and interesting options are discussed below.
The use of home-made machines and devices for the home workshop is aimed at solving several problems:
- Simplification of the metal processing process. In the course of creating household items, a metal carver or a press is often required.
- Improvement in wood processing. Even to build a small shed or make a wooden shelf for the house, you need a power saw and other woodworking tools.
Buying a ready-made tool is quite expensive, so the use of home-made machines and accessories for the garage is becoming more and more relevant every day. Among the most common options for home tools are:
- carpentry workbench;
- device for quick sharpening of knives;
- device for sharpening metal drills;
- drilling machines;
- press;
- cutting disc machines.
Here are a few photos of do-it-yourself tools and fixtures from "homemade" ones:
Practical DIY tool shelves
Before creating devices and tools for do-it-yourself work, determine the storage location for all devices, so that later you don’t have to look all over the workshop or garage where everything is. It is not difficult to make a shelf for tools with your own hands, the main thing is to decide on its dimensions and material of manufacture.
The easiest way to make shelves is to assemble them from wood. Do not forget about the need to cover the finished structure with a protective varnish or paint to prevent rotting and swelling of the wood.
You can create a combined version of the rack from a metal support and wooden shelves. Here are detailed instructions for creating such a homemade model:
| Image | Sequencing |
|
Assemble the frame. To do this, prepare two side frames, consisting of 4 corners. Connect the elements with self-tapping screws. Then, tighten 2 frames together using 4 corners. |
|
When the frame is fully assembled, proceed to the manufacture of shelves. They can be made from wood or metal, as well as from other improvised dense materials. It is enough to cut the canvases of a suitable size and fix them on a metal base. |
 |
If desired, you can make the rack movable by attaching four small wheels. Or firmly install it in the allotted place in the garage. |
You can find other interesting projects and drawings for making tool shelves. Watch a video on the topic:
And also make useful household appliances with your own hands:
We make a carpentry workbench with our own hands according to the drawings: video instructions and photo examples
Among the common fixtures for a carpentry workshop, a workbench is distinguished with their own hands. A durable and dimensional table that allows you to securely fix the workpiece is useful for high-quality cutting of wood and creating various elements from it.
The device package includes:
- Working surface. For her use solid wood to extend the life of the device. The thickness must be at least 6 cm.
- Supports. Assembled from wooden beams or metal plates. The main task is to ensure the stability of the entire mechanism.
- Vice for fixing the product. If the table is long, you can install two vices at once.
- Tool box. A useful recess or pull-out design that provides quick access to the small parts you need.
To independently assemble a carpentry workbench for your workshop, you should choose a drawing, purchase material for work.
Do-it-yourself carpentry workbench drawings
Before buying materials to build your own workbench, you should think about a detailed drawing. It should include the dimensions of the machine itself, it is advisable to note the dimensions of the materials used and their quantity.
For example, a finished drawing of a folding workbench with your own hands may look like this:
Whatever model you choose to create, consider several features of the desktop that provide the convenience of cutting wood:
- the height and length of the hands of the master: the height and width of the countertop depend on these parameters;
- which hand is working: place the vise on the right or left;
- what blanks will be made: selection of the table shape;
- how much space in the room you allocate for a workbench.
Given all these parameters, it will be easier for you to decide on the drawings of the carpentry workbench and the dimensions of the machine. Here are some interesting examples:
Instructions for assembling a wooden workbench with your own hands
You can buy a wooden workbench in a store or through online catalogs, but it's cheaper to make it yourself. Let's take as a basis a simple version with typical tabletop dimensions: length - 150-200 cm, width 70-120 cm.
Manufacturing work will include several stages:
| Image | What need to do |
|
You make the top cover from thick boards to make a shield with a width of 70 to 200 cm. Fasten the elements onto long nails, and you need to drive them in from the outside, and carefully bend them from the inside. The working surface of the workbench is made only of wood or chipboard. |
|
Sheathe the lid along the lower perimeter with a 5 by 5 cm timber. This will make it more convenient to mount the vertical supports. The location of the supports depends on the size of the countertop. It is better to make them from a thick rectangular bar at least 120 by 120 mm. |
|
The carpenter's workbench must be installed correctly. Be sure to fasten it firmly. If it will be mounted on the street under a canopy, then dig holes for the supports. Indoors, use other methods of fastening. |
When the structure is assembled, place a vise on it. To fully understand how to assemble a carpentry workbench with your own hands, watch the video:
Making a carpenter's vise for a workbench with your own hands
Professional "homemade" assemble not only tables for work, notes with their own hands according to the drawings. Any design of such a clamp will include several elements:
- Supports where each has a sponge for clamping.
- Moving clamping jaw.
- Metal guides. A sponge moves over them.
- Lead screw, for moving elements.
- collar. Required to rotate the screw.
In the manufacture of homemade vise with your own hands, you can use various improvised materials. For example, there is a design option from a profile pipe. To do this, prepare several pieces of pipe of different sizes, a steel stud with a large thread and double nuts.
Instructions for creating a verstal vice from a profile pipe:
| Image | What need to do |
|
The largest pipe acts as a body. Supports are soldered to it from below. A 3-4 mm steel flange is put on the back side. A hole for the running nut is drilled in the center, and a rear sponge is welded opposite the front support. |
|
A front steel flange is welded onto the inner moving part. A stud is mounted in it, with lock nuts fixed to it. Thrust washers are put on both sides of the flange. The last element is a movable tube attached to the front sponge. |
And also watch the video "do-it-yourself vise at home":
Do-it-yourself metal workbench drawings
A carpenter's metal workbench does not have much difference from a metal workbench. At the heart of a rigid metal, not a wooden frame. A vise is attached to it, and the entire workbench is designed to withstand the force of a blow from a sledgehammer.
Do-it-yourself metal workbenches can have one, two or three cabinets, and also not have shelves and drawers for small parts. In terms of strength for working in a garage, you can make an ordinary table of metal up to 5 mm thick and a reinforced structure, where sheets from 10 to 30 mm are applicable.
Here are some useful blueprints for making a metal workbench for your workshop:
How to make a do-it-yourself knife sharpener: drawings and photo examples
No home is complete without a knife in the kitchen. Correct sharpening it is rather difficult to do without special devices: it is necessary to maintain the desired angle and achieve the ideal sharpness of the blade.
For each knife, a certain sharpening angle must be observed:
- Razor and scalpel require an angle of 10-15⁰.
- Knife for cutting bakery products - 15-20⁰.
- Classic multifunctional knives - 25-30⁰.
- For hunting and camping, they take a device with a blade angle from 25 to 30⁰.
- If you want to cut hard materials, then sharpen at an angle of 30-40⁰.
To ensure the desired angle, it is worth buying or making a sharpening device. For example, you can assemble a sharpener from engines from washing machines with your own hands.
To assemble such a machine, a motor from a “washer” with a power of 200 watts is useful. If you do not use sharpening every day, then 1000 rpm is enough for a high-quality result and a long service life of the device.
Completely to create a grindstone from the engine from the washing machine, prepare:
- the motor itself;
- metal for the casing with a thickness of 2 to 2.5 mm;
- tube for the flange;
- sharpening stone;
- nuts;
- starting mechanism;
- cable for connection to the mains;
- metal corner or wooden beam for the bed.
You can see a step-by-step description of the manufacture of the machine in the video:
There are simple do-it-yourself grinding machines without engines. For example, you can make a device from bars. To do this, prepare two abrasive bars of the same size and a sharpening stone.
The progress of work on the creation of such a simple device will be as follows:
- Sand the wood blocks with sandpaper to remove any burrs. Make a markup depending on the desired angle.
- Attach a stone to the drawn line to sharpen the blade. To do this, attach it to the bar and mark its width. Then, on the markings, make cuts, up to 1.5 cm deep.
- In the resulting recesses, fix the abrasive bars so that the grooves match. Then, install the sharpening stone by screwing it onto the bolts.
There are many ways to make a homemade knife sharpener. Choose the right one and try to create a convenient and useful tool for the home.
How to make a do-it-yourself tool for sharpening a drill for metal
They independently make not only a sharpener for blades, but also a machine for sharpening drills for metal. Here are some drawings to help you get started:
To understand how to properly assemble according to the drawings own machine for sharpening drills, watch the video
The master is not distinguished by the greed that some masters suffer from, who do not want to share their findings with others and, like a dog in the manger, neither to themselves nor to people. And this self-taught inventor came up with a great gadget with which you will always be on top and can even improve your standard of living. Why, you can put on stream the production of such an instrument and sell it to everyone. Maybe this is too loud, but you should think about automating and mechanizing all the routine work at home.
8 accessories for craftsmen.
You probably haven't seen many of them. Cool tools create DIYs. These devices will help you work more comfortably in the workshop. The video was filmed on the channel “Hands from Shoulders”.
Folding table for the master
1. Let's start with a folding table, which will be a great helper in a small workshop. Helps save money too small area. The table has a compartment for small things. Shelf that can be laid out essential tool. Thanks to a large number holes with a clamp, you can conveniently and quickly fix the workpieces being processed. Stops are inserted into them. It is convenient to fix the parts in a vertical position. If inserted into the guide bolts, we get additional emphasis. Having a set of clamps and such a table, you can comfortably perform a variety of jobs.
Folding stand homemade
2. Very original idea folding stand for hand tool. Everyone is in their place. It doesn't take up much space. The design is based on furniture guides. the stand is held in the upper position. Neodymium magnets prevent instruments from falling out of their stocks. Great idea for the Samodelkins, who love to do everything with their own hands.
Apple puller
3.Gardeners will be interested in the fruit puller. Its advantage over analogues is the absolute free of charge and ease of manufacture. Not at all hard to find plastic bottle, rope and cut the stick. 5 minutes and you can go for apples.
Handicraft apple press
4. If the harvest is large, then the question arises, where to put it? Great option- Apple juice. For purchased juicers, apples need to be cut and peeled, which is inconvenient. The grater below will handle whole apples. Dali only remains to squeeze the resulting mass under pressure. The result is a natural delicious juice and almost dry cake.
Tool trolley
5. The mobile tool cart is very convenient for the workshop. When, for example, the workbench is littered with parts. Or it doesn't exist at all. By downloading everything you need to this moment, we get the entire tool in one place at your fingertips.
What can be done from an electric planer with your own hands
6. Another interesting thickness gauge design is based on an electric planer. With the help of guides, it moves in 2 planes. The movement takes place with the help of an elevator. There are rulers on each side of the fixture for fine adjustment.
Grinding tool
7. Having a jigsaw, you can get a cool grinder. Interestingly, it is not the abrasive that moves, but the workpiece itself.
Cheap homemade grinder
8. The most budget version of the grinder, created by the Samodelkins. Plastic bottles are used as rollers. They are seated on bearings. Adjustment of the tape on the rollers occurs with the help of lambs. The tension is adjustable with a bolt. The structure is set in motion with a drill. You can slightly improve the design by Samodelkin by replacing plastic bottles with polypropylene tubes.
Homemade self-taught shook the network with his video
The self-taught inventor conquered the online community of craftsmen with his video, in which he presented a fundamentally new utility model to improve the efficiency of the work of craftsmen and those who like to work in the garage. The best part is that it doesn't require buying an idea. And moreover, all this can be done by yourself and even a novice master can handle it. All this is for the benefit of every resident of the cities in which the masters settled, because with such high level mastery, now you don’t want to hammer walls on weekends at home or rattle some kind of ultra-decibel grinder incomprehensible purpose. With such a device, you can safely make your own separate workshop and live the rich life of a Russian artisan.
DIY tool stirs up the web
This video stirred up the community of lovers of inventions in the global network. The master thought about this idea for years and finally brought to the public discussion a brilliant idea in terms of simplicity and a radically beneficial idea for those who used to hammer walls with a perforator, realize their inclinations of a woodpecker and a brilliant builder-grinder, and now can make themselves rich for free, working in silence workshop in the garage or even in a detached building.
And at the same time, you don’t have to spend money and take out the money saved for beer from the stash. All this is free - the master loves to show the whole world the useful things that he comes up with.
Uprooter of seedlings and weeds from a square for do-it-yourselfers
Good afternoon My prolonged absence on the channel was not in vain, during this time I managed to do a lot of household chores. And of course, stock up on a bunch of homemade products that I will show you, my dear subscribers and guests! It makes no sense to post everything at once, because it also takes a lot of time, but if possible I will try to post at least one a day. Not only am I sitting at the computer, I can’t leave my workshop. Fussing in the garden is another hobby of mine, I spent a lot of time there in the summer. Caring for plants, weeding, although a pleasant experience, however, also requires a lot of strength. And how I would like to make things easier. Wanting alone is not enough, so you have to make yourself useful, which will facilitate the work and make it a pleasure, and not hard labor with a farm laborer.
Today I will show you a device that I have successfully used for almost the entire spring and summer and will last, God forbid, more than one season. Do-it-yourself rooter For manufacturing, I took a square with walls 40 by 40 mm, 220 mm long. I didn’t cut off such a length on purpose, I had a lot of such trimmings from others construction works. 
I drew two oblique lines along the walls to the corner of the square. Cutting out, it turned out such a horn. In inner part square welded a pipe with a diameter of 25 mm. From the outside, I welded a square right in the middle of the square. Instead of a square, you can weld a square, but it seemed to me that it would be more convenient. 
I installed a metal handle in the pipe so that it would not break under load, because the force falls mainly on the handle. Working with a flat cutter, some types of weeds still germinate after a certain time, especially after rains. And tearing it out with roots, I ruled out such a possibility and my garden became well-groomed and beautiful. Without damaging the root system, they can still take out seedlings for transplanting, which I did at the beginning of the season with strawberries and other plants. 
A simple penny homemade device for picking berries
Gooseberries are a tasty and healthy berry. The plant itself is quite unpretentious, it does not require any special care. Berries grow large, it is quite convenient to collect them. And everything would be fine if it were not for the thorny gooseberry branches. Because of these garden "cacti" before, the hands were constantly in small scratches. And several times you will think “do you need it - so many berries” before you climb deep into the bush for the harvest. But a few years ago, my husband made my life easier. He spied on the Internet one very simple, but useful device for picking berries. What is it for and how is it useful? 
In fact, such a picker can be used not only for collecting gooseberries. I also use it to pick any other berries / fruits in hard-to-reach places where it’s so easy to reach with your hand. For example, to remove plums, cherries or apples from high branches. How to make a device for collecting gooseberries? Everything ingenious is simple! We take a plastic bottle and cut a hole in the side in the form of a droplet. Depending on what kind of berries / fruits you have a picker, we make this drop diameter. For gooseberries, 5-7 cm is enough, for apples and plums more, so that you do not have to aim for a long time and try to hit the fruit. The volume of the bottle will also depend on what you will be collecting. For berries better fit bottle 0.5 l. 
The spout of the droplet should point towards the bottom of the bottle. You can also make an incision a couple of centimeters in the continuation of the nose, so that the twig is better captured. Everything, our device is ready! We will collect berries by holding it by the neck.
It's actually much easier to do it with him. Not only do the hands remain scratch-free, but also the work goes faster. After all, the harvested crop will be poured into the top of the bottle. Accordingly, it is not necessary to “get out” of the bush after each berry, put the crop in a can or jar and climb again. Plus, we can get berries even from the most inaccessible places. And most importantly - that such a device is made in 3 minutes, does not cost a penny, and life simplifies at times. If it gets lost, gets dirty, it doesn't matter - we'll do another one without any problems! So, gardeners, take advantage! If the article was useful to you, put a "thumbs up" and subscribe to the channel for summer residents and gardeners "SADOEZH".
